ATEN PN0108 Manuel utilisateur

Power over the NET™

PN0108

User Manual

www.aten.com

PN0108 User Manual

ii

FCC, CE Information

FEDERAL COMMUNICATIONS COMMISSION INTERFERENCE

STATEMENT: This equipment has been tested and found to comply with the

limits for a Class A digital device, pursuant to Part 15 of the FCC Rules. These

limits are designed to provide reasonable protection against harmful

interference when the equipment is operated in a commercial environment.

This equipment generates, uses, and can radiate radio frequency energy and, if

not installed and used in accordance with the instruction manual, may cause

harmful interference to radio communications. Operation of this equipment in

a residential area is likely to cause harmful interference in which case the user

will be required to correct the interference at his own expense.

FCC Caution: Any changes or modifications not expressly approved by the

party responsible for compliance could void the user's authority to operate this

equipment.

CE Warning: This is a class A product. In a domestic environment this product

may cause radio interference in which case the user may be required to take

adequate measures.

RoHS

This product is RoHS compliant.

SJ/T 11364-2006

The following contains information that relates to China.

PN0108 User Manual

iii

User Information

Online Registration

Be sure to register your product at our online support center:

Telephone Support

For telephone support, call this number:

User Notice

All information, documentation, and specifications contained in this manual

are subject to change without prior notification by the manufacturer. The

manufacturer makes no representations or warranties, either expressed or

implied, with respect to the contents hereof and specifically disclaims any

warranties as to merchantability or fitness for any particular purpose. Any of

the manufacturer's software described in this manual is sold or licensed as is.

Should the programs prove defective following their purchase, the buyer (and

not the manufacturer, its distributor, or its dealer), assumes the entire cost of all

necessary servicing, repair and any incidental or consequential damages

resulting from any defect in the software.

The manufacturer of this system is not responsible for any radio and/or TV

interference caused by unauthorized modifications to this device. It is the

responsibility of the user to correct such interference.

The manufacturer is not responsible for any damage incurred in the operation

of this system if the correct operational voltage setting was not selected prior

to operation. PLEASE VERIFY THAT THE VOLTAGE SETTING IS

CORRECT BEFORE USE.

International http://eservice.aten.com

International 886-2-8692-6959

China 86-10-5255-0110

Japan 81-3-5615-5811

Korea 82-2-467-6789

North America 1-888-999-ATEN ext 4988

United Kingdom 44-8-4481-58923

PN0108 User Manual

iv

Package Contents

The PN0108 package consists of:

1 PN0108 Station

1 AC Source Power Cord

8 Power Outlet Power Cords

8 Safe Shutdown Cables

1PON Cable (DB9 F to DB9 M)

1 Rack Mount Kit

1 Foot Pad Set (4 pcs.)

1 Software CD

1 User Manual*

1 Quick Start Guide

Check to make sure that all of the components are present and in good order.

If anything is missing, or was damaged in shipping, contact your dealer.

Read this manual thoroughly and follow the installation and operation

procedures carefully to prevent any damage to the switch or to any other

devices on the PN0108 installation.

*Features may have been added to the PN0108 since this manual was

published. Please visit our website to download the most up-to-date version

of the manual.

Manual Part No. PAPE-0239-3AXG

Manual Date: 2014-04-28

All other brand names and trademarks are the registered property of their respective owners.

PN0108 User Manual

v

Contents

FCC, CE Information. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ii

SJ/T 11364-2006. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ii

User Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .iii

Online Registration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .iii

Telephone Support . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .iii

User Notice . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .iii

Package Contents. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . iv

About This Manual . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .viii

Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .viii

Conventions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ix

Product Information. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ix

Chapter 1.

Introduction

Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1

Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3

Requirements . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4

Components . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5

Front View . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5

Rear View . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7

Chapter 2.

Hardware Setup

Before You Begin . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9

Stacking and Rack Mounting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9

Stacking. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9

Rack Mounting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10

Single Stage Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .11

Single Stage Installation Diagram . . . . . . . . . . . . . . . . . . . . . . . . .12

Daisy Chaining . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .13

Daisy Chain Installation Diagram. . . . . . . . . . . . . . . . . . . . . . . . . . 13

Chapter 3.

Logging In

Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .15

CN-6000 Browser Login . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15

Logging In . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15

PN9108 Browser Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18

Logging In . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18

The PN9108 Main Screen . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .19

SN0108 / SN0116 Browser Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . 20

Logging In . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20

The SN0108 / SN0116 Main Screen . . . . . . . . . . . . . . . . . . . . . . . . . . 21

Local Console Operation. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25

PN0108 User Manual

vi

Hyperterminal . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25

Logging In:. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28

Java Application . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29

Windows Setup: . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29

Running the Application: . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30

Chapter 4.

Operation

The PN0108 Main Screen . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31

Device Selector. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32

Device Control. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32

The Power Status Screen . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33

Power Sockets: . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33

The Information Panel: . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34

Chapter 5.

Administration

System Setup . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37

Administrator . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37

Connection Control . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37

Device Control . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 38

Configuration. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 38

Outlet Configuration: . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 39

Outlet Groups: . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 41

Finishing Up . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 41

Schedule . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 42

Finishing Up . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 42

User Management. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 43

Finishing Up . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 43

Monitor . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 44

Log . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 45

Chapter 6.

Safe Shutdown and Reboot

Overview. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 47

BIOS Power Management Settings . . . . . . . . . . . . . . . . . . . . . . . . . . 47

Automated Setup . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 48

Installation. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 48

Uninstalling . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 49

Manual Setup . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 50

Windows 2000 / XP / Server 2003: . . . . . . . . . . . . . . . . . . . . . . . . . . . 50

NT: . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 52

Chapter 7.

Upgrading The Firmware

Preparation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 53

PN0108 User Manual

vii

Starting the Upgrade. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 55

Upgrade Succeeded . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .58

Upgrade Failed . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 59

Firmware Upgrade Recovery . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .60

Single Station Recovery . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .60

Daisy Chained Station Recovery. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 60

Appendix

Safety Instructions. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 61

General . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 61

Rack Mounting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 63

Consignes de sécurité. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 64

Général . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 64

Montage sur bâti . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 67

Power Cords . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .68

Power Cord:. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .68

Power Outlet Cords: . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 68

Technical Support . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 69

International. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 69

North America . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 69

Troubleshooting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 70

Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .70

Problem 1: . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .70

Solution:. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 70

Problem 2: . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .71

Solution:. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 71

Problem 3: . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .71

Solution:. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 71

Problem 5: . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .72

Solution:. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 72

Problem 6: . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .72

Solution:. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 72

Problem 7: . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .72

Solution:. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 72

Supported Devices . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 73

Administrator Login Failure . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 74

Trusted Certificates. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .75

Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .75

Installing the Certificate . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 76

Certificate Trusted . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 77

Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 78

Limited Warranty . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 79

PN0108 User Manual

viii

About This Manual

This User Manual is provided to help you get the most from your PN0108

system. It covers all aspects of installation, configuration and operation. An

overview of the information found in the manual is provided below.

Overview

Chapter 1, Introduction, introduces you to the PN0108 system. Its

purpose, features and benefits are presented, and its front and back panel

components are described.

Chapter 2, Hardware Setup, provides step-by-step instructions for setting

up your installation.

Chapter 3, Logging In, describes the various methods that can be used to

access the PN0108.

Chapter 4, Operation, explains how to set up and operate the PN0108 once

you are logged in.

Chapter 5, Administration, describes the administrative procedures that

are employed to configure the PN0108's working environment.

Chapter 6, Safe Shutdown and Reboot, shows you how to safely close

a system down and reboot your devices without involving the danger to the file

systems that simply killing the power supply does.

Chapter 7, Upgrading The Firmware, explains how to upgrade the

PN0108's firmware with the latest available versions.

An Appendix, provides specifications and other technical information

regarding the PN0108.

PN0108 User Manual

ix

Conventions

This manual uses the following conventions:

Product Information

For information about all ALTUSEN products and how they can help you

connect without limits, visit ALTUSEN on the Web or contact an ALTUSEN

Authorized Reseller. Visit ALTUSEN on the Web for a list of locations and

telephone numbers:

Monospaced Indicates text that you should key in.

[ ] Indicates keys you should press. For example, [Enter] means

to press the Enter key. If keys need to be chorded, they

appear together in the same bracket with a plus sign

between them: [Ctrl+Alt].

1. Numbered lists represent procedures with sequential steps.

♦Bullet lists provide information, but do not involve sequential

steps.

→Indicates selecting the option (on a menu or dialog box, for

example), that comes next. For example, Start → Run

means to open the Start menu, and then select Run.

Indicates critical information.

International http://www.aten.com

North America http://www.aten-usa.com

PN0108 User Manual

x

This Page Intentionally Left Blank

1

Chapter 1

Introduction

Overview

The PN0108 Power Over the NET™ is a control unit that offers remote power

management for up to eight devices (computers, hubs, routers, etc.). When

connected to an ATEN or Altusen TCP/IP accessible module via its PON

(RS232) port – see the diagram below – it allows administrators from any

computer connected to the internet, whether down the hall, or half way around

the world – to control the power off, power on, and reboot status for each

attached device. See Supported Devices, page 73 for a list of compatible

ATEN/ALTUSEN devices.

PN0108

Remote

Administrator

TCP/IP

Local Terminal

Connection

PON (RS232)

Port

ATEN/ALTUSEN

Over IP

Device

PN0108 User Manual

2

For flexibility, the PON port can also be used to administer the PN0108 locally

via a serial terminal session.

Up to 15 additional PN0108 units can be daisy chained down from the original

unit, providing remote power management for up to 128 devices. Installation

is fast and easy: plugging cables into their appropriate ports and a simple setup

is all that is entailed.

Since the PN0108's firmware is upgradeable, you can stay current with the

latest functionality improvements simply by downloading firmware updates

from our website as they become available.

With its advanced features and ease of operation, the PN0108 is the most

convenient, most reliable, and most cost effective way to remotely manage

power access for multiple computer installations.

PN0108

Local Terminal

Connection

PON (RS232)

Port

Chapter 1. Introduction

3

Features

Remote power on/off/reboot control for eight outlets via TCP/IP and a

built in RS-232 PON (Power over the Net™) port

Local power on/off/reboot control via the PN0108's PON port to the

computer's RS-232 port

Daisy chain up to 15 additional stations to control up to 128 outlets

Manual switching between Local and Remote access for each port via

front panel push button switches

Individual control of each port – users can set the power on sequence and

delay time for each port to allow equipment to be turned on in the proper

order

Easy setup and operation via a GUI interface

Provides three configuration/management methods: Browser; Telnet; or

Console Terminal

Safe shutdown and rebooting for Windows systems*

Overcurrent protection and recovery for each AC port (110 V model only);

total port overcurrent protection (both models) – remote users can monitor

the current status via the GUI interface

Separate circuits for the unit's power and the power to the devices – the

power control status menu is still accessible even when an overcurrent

condition trips the devices' circuit breaker

On/Off scheduling – allows everything from a one-time start/shutdown, to

daily, weekly, etc. starts/shutdowns at user-specified times

Port grouping – perform the same action on a specified group of ports

LEDs for easy status monitoring

Two level (Administrator and User) security

Configuration can be reset

Firmware upgradeable – daisy chained stations receive the upgrade via the

daisy chain bus

*Safe shutdown and rebooting is supported if the Power Monitor utility has

been installed (see Automated Setup, page 48).

PN0108 User Manual

4

Requirements

Browsers accessing the PN0108 must support SSL 128 bit encryption.

For the Java access, you must have Java J2RE (1.4 or higher) installed on

your computer. Java is available for free download from the Sun Java

website: http://java.sun.com

For cold booting of attached computers, the computer's BIOS must

support this feature.

For Safe Shutdown:

The computer must be running Windows (Windows 98 or higher).

The computer's BIOS must support Safe Shutdown – see Overview,

page 47, for detailed information.

There must be an available COM port on the computer for the Safe

Shutdown cable to plug into.

Chapter 1. Introduction

5

Components

Front View

(Continues on next page.)

No. Item Description

1 Port LEDs The Port LEDs provide status information about their

corresponding AC outlet ports. There is one pair of LEDs for each

port. The one on the left is the Remote Access LED; the one on

the right is the Power LED:

A Remote Access LED lights GREEN to indicate that the device

attached to its corresponding port is capable of being controlled

remotely.

A Power LED lights ORANGE to indicate that there is electricity

going to its corresponding outlet. The LED flashes under the

following conditions:

If Modem Ring Resume is enabled (see Modem Ring

Resume*, page 39), an outlet still receives electricity even

when its corresponding computer has been powered OFF.

The Power LED blinks OFF, then ON for 8 seconds, then

OFF, then ON for 8 seconds, etc., to indicate this situation.

When a power status change is pending, the LED flashes

until the change has taken place.

If both LEDs flash it indicates that there is either an overcurrent

situation, or the relay has failed. See Flashing Lightbulb,

page 33, for more details.

2 Firmware

Upgrade

Switch

During normal operation this switch is in the NORMAL position.

The RECOVER position is used when performing a firmware

upgrade. See Upgrading The Firmware, page 53, for upgrading

details.

2 4 5 63

1

PN0108 User Manual

6

(Continued from previous page.)

No. Item Description

3 Power

Control

Buttons

Each button (A to H), controls the power status of its

corresponding AC output port as follows:

Pressing the button for less than 3 seconds toggles the port

between Remote Access enabled and Remote Access disabled

(Local Mode). If Remote Access is disabled, the switch does not

allow the port to be managed from a remote connection. (The

Remote Access LED is off when Remote Access Mode has

been disabled for its corresponding port.)

Under Local Mode, pressing and holding the button in for more

than 3 seconds switches the power to its corresponding port On

or Off.

4 Reset

Switch

Pressing and holding this switch in for more that three seconds

resets the PN9108 to its factory default settings. This switch is

recessed and must be pushed with a thin object, such as the end

of a paper clip, or a ballpoint pen.

5 Station ID

LED

The PN0108's Station ID displays here. If this is a Single Station

installation (See Single Stage Installation, page 11, or the First

Station on a Daisy Chained installation (see Daisy Chaining,

page 13), the PN0108 has a Station ID of 01.

6 Power

Switch

This standard rocker switch powers the PN0108 On and Off.

Chapter 1. Introduction

7

Rear View

No. Item Description

1 Power

Socket

The power cable from the AC source plugs in here.

2Circuit

Breaker

Press to reset the circuit.

3 AC Power

Outlets

The power cables that connect to the computers plug in here.

4 Safe

Shutdown

Ports

Provides safe shutdown and rebooting for Windows 98SE, ME,

NT, 2000, XP and 2003 Server systems.

5PON

(Power

over the

NET™)

Output Port

When daisy chaining PN9108 Stations, this is the Chain Out port.

See p. 13 for daisy chaining details.

6 PON Input

Port

For a single unit installation, or for the first station of a daisy

chained installation, the PON cable that connects to the CN-

6000 (or other compatible device - see Supported Devices,

page 73), plugs in here.

In a daisy chained installation, the PON cable from the Chain

Out port of the parent unit plugs in here.

When performing a firmware upgrade, the PON cable that

connects the PN0108 to the computer that will transfer the

upgraded firmware (see Preparation, page 53), plugs in here.

6

3 41 2 5

PN0108 User Manual

8

This Page Intentionally Left Blank

9

Chapter 2

Hardware Setup

Before You Begin

Stacking and Rack Mounting

Stacking

The PN0108can be placed on any appropriate level surface that can safely

support its weight plus the weight of its attached cables. To place or stack the

PN0108, remove the backing material from the bottom of the rubber feet that

came with this package, and stick them onto the switch's bottom panel at the

corners, as shown in the diagram, below

Note: To ensure adequate ventilation, allow at least 5.1 cm on each side, and

12.7cm at the back for power cord and cable clearance.

1. Important safety information regarding the placement of this

device is provided on page 61. Please review it before

proceeding.

2. Make sure that power to all the devices you will be connecting

up have been turned off. You must unplug the power cords of

any computers that have the Keyboard Power On function.

PN0108 User Manual

10

Rack Mounting

The PN0108 can be installed in most standard 19" (1U) racks. To rack mount

the unit do the following:

1. Use the screws supplied with your rack mounting kit to attach the rack

mounting brackets to each side of the device:

Note: The unit can be installed either at the front or the back of the rack.

To install it at the back, simply screw the brackets into the holes at

the rear of the unit.

2. Position the device in the rack and align the holes in the mounting brackets

with the hole in the rack.

3. Screw the mounting brackets to the rack.

Note: Cage nuts are provided for racks that are not prethreaded.

Phillips Hex Head

M3 x 8

La page charge ...

ATEN PN0108 Manuel utilisateur

Ce manuel convient également à

ATEN PN0108 Manuel utilisateur

dans d''autres langues

Documents connexes