RIDGID เครื่องมือทำความสะอาดท่อระบายน้ำรอบผนังท่อ FlexShaft รุ่น K9-12 Manuel utilisateur

Model K9-12 FlexShaft™

Drain Cleaning Machine

• Français – 19

• Deutsch – 41

• KO – 63

• JA – 83

K9-12 Manual

RIDGID.com/qr/k9-12

999-995-413.08_REV. E

ii

K9-12 FlexShaft™ Drain Cleaning Machine

Table of Contents

Safety Symbols .................................................................................................................... 2

General Safety Rules

Work Area Safety .............................................................................................................. 2

Electrical Safety ................................................................................................................ 2

Personal Safety ................................................................................................................. 2

Tool Use and Care ............................................................................................................ 3

Service .............................................................................................................................. 3

Specific Safety Information ................................................................................................ 3

FlexShaft Drain Cleaning Machine Safety ........................................................................ 3

RIDGID Contact Information ............................................................................................... 4

Description ........................................................................................................................... 4

Specifications ...................................................................................................................... 5

Specifications - Acceptable Battery Powered Drills .......................................................... 5

Standard Equipment ......................................................................................................... 5

Pre-Operation Inspection .................................................................................................... 5

Machine and Work Area Set-up .......................................................................................... 6

Battery Powered Drill Set-up and Operation ..................................................................... 8

Drill Switch ........................................................................................................................ 8

Drill Speed ........................................................................................................................ 8

Drill Adjustable Clutch Setting ........................................................................................... 8

Installing/Adjusting Chain Knocker ................................................................................... 9

Installing Brushes ........................................................................................................... 12

Installing Penetrating Head ............................................................................................. 13

Operating Instructions ...................................................................................................... 13

Using Machine With Brushes .......................................................................................... 16

Draining the Drum .......................................................................................................... 17

Transportation and Storage .............................................................................................. 17

Maintenance Instructions ................................................................................................. 17

Cleaning ......................................................................................................................... 17

Lubrication ...................................................................................................................... 17

Cable Assembly Replacement ........................................................................................ 17

Troubleshooting .............................................................................................................. 18

Service And Repair ......................................................................................................... 18

Optional Equipment .......................................................................................................... 18

Disposal.............................................................................................................................. 18

EC Declaration of Conformity .................................................................. Inside Back Cover

Lifetime Warranty ................................................................................................. Back Cover

*Original Instructions - English

Model K9-12 FlexShaft™

Drain Cleaning Machine

WARNING!

Read this Operator’s Man ual

carefully before using this

tool. Failure to understand

and follow the contents of

this manual may result in

electrical shock, fire and/or

serious person al injury.

Drain Cleaning Machine

K9-12 FlexShaft™ Drain Cleaning Machine

999-995-413.08_REV. E

2

This symbol indicates the risk of hands,

fingers or other body parts being caught,

wrapped or crushed in the drain cleaning

FlexShaft.

Safety Symbols

In this operator’s manual and on the product, safety symbols and signal words are used to

communicate important safety information. This section is provided to improve understand-

ing of these signal words and symbols.

This is the safety alert symbol. It is used to alert you to potential personal injury hazards. Obey

all safety messages that follow this symbol to avoid possible injury or death.

DANGER indicates a hazardous situation which, if not avoided, will result in death

or serious injury.

WARNING indicates a hazardous situation which, if not avoided, could result in death

or serious injury.

CAUTION indicates a hazardous situation which, if not avoided, could result in minor

or moderate injury.

NOTICE indicates information that relates to the protection of property.

Electrical Safety

• Avoid body contact with earthed or

grounded surfaces such as pipes, ra-

diators, ranges and refrigerators. There

is an increased risk of electrical shock if

your body is earthed or grounded.

• Do not expose power tools to rain or

wet conditions. Water entering a power

tool will increase the risk of electrical

shock.

• If operating a power tool in a damp lo-

cation is unavoidable, use a ground

fault circuit interrupter (GFCI) protected

supply. Use of a GFCI reduces the risk of

electric shock.

Personal Safety

• Stay alert, watch what you are doing

and use common sense when oper-

ating tools. Do not use tools while

you are tired or under the influence of

drugs, alcohol, or medication. A mo-

ment of inattention while operating tools

may result in serious personal injury.

General Safety Rules

WARNING

Read and understand all warnings and

instructions. Failure to follow all warn-

ings and instructions may result in elec-

tric shock, fire, and/or serious injury.

SAVE THESE INSTRUCTIONS!

Work Area Safety

• Keep work area clean and well lit. Clut-

tered or dark areas invite accidents.

• Do not operate tools in explosive at-

mospheres, such as in the presence

of flammable liquids, gases, or dust.

Tools create sparks which may ignite the

dust or fumes.

• Keep children and by-standers away

while operating tools. Distractions can

cause you to lose control.

• Keep floors dry and free of slippery

materials such as oil. Slippery floors

invite accidents.

NOTICE

DANGER

WARNING

CAUTION

This symbol means read the operator’s

manual carefully before using the equip-

ment. The operator’s manual contains im-

portant information on the safe and proper opera-

tion of the equipment.

This symbol means always wear safety

glasses with side shields or goggles while

using this equipment to reduce the risk of

eye injury.

This symbol indicates the risk of the elec-

trical shock.

This symbol indicates the risk of fingers or

other body parts being caught, wrapped,

crushed or struck by the chain knocker.

Do not operate tool with the cable end outside

of the drain.

This symbol means always wear gloves

when handling or using this equipment to

reduce the risk of infections, burns or other

serious personal injury from the drain contents.

K9-12 FlexShaft™ Drain Cleaning Machine

999-995-413.08_REV. E 3

FlexShaft Drain Cleaning

Machine Safety

• Always use safety glasses and gloves

in good condition while handling or

using. Use latex or rubber gloves, face

shields, protective clothing, respirators or

other appropriate protective equipment

when chemicals, bacteria or other toxic

or infectious substances are suspected to

be present to reduce the risk of infections,

burns or other serious personal injury.

• Do not use with a corded drill. Opera-

ting with a corded drill increases the risk

of electrical shock and other injuries.

• Do not allow the chain knocker/end of

cable to stop turning while drill switch

is depressed. This can over-stress the

cable and may cause twisting, kinking or

breaking of the cable assembly and may

result in serious personal injury.

• Practice good hygiene. Do not eat or

smoke while handling or operating the

tool. After handling or operating drain

cleaning equipment, use hot, soapy

water to wash hands and other body

parts exposed to drain contents. This

will help reduce the risk of health hazards

due to exposure to toxic or infectious ma-

terial.

• Only use the FlexShaft Drain Clean-

ing Machine for the recommended

drain sizes. Using the wrong size drain

cleaner can lead to twisting, kinking or

breaking of the cable and may result in

personal injury.

• Keep hand on the cable assembly

whenever the FlexShaft Machine is run-

ning. This provides better control of the

cable and helps prevent twisting, kinking

and breaking of the cable and reduces the

risk of injury.

• Position machine cable outlet within

3' (1 m) of the drain inlet or properly

support exposed cable assembly when

the distance exceeds 3' (1 m). Greater

distances can cause control problems lead-

ing to twisting, kinking or breaking of the

cable. Twisting, kinking or breaking cable

may cause striking or crushing injuries.

• One person must control both the

cable assembly and cordless drill. Do

not lock drill switch in the ON position

during operation. If the cable stops rotat-

ing, the operator must be able to release

the drill switch to prevent twisting, kinking

• Use personal protective equipment.

Always wear eye protection. Protective

equipment such as dust mask, non-skid

safety shoes, hard hat, or hearing protec-

tion used for appropriate conditions will

reduce personal injuries.

• Do not overreach. Keep proper footing

and balance at all times. Proper footing

and balance enables better control of the

tool in unexpected situations.

Tool Use and Care

• Do not force tool. Use the correct tool

for your application. The correct tool will

do the job better and safer at the rate for

which it is designed.

• Store idle tools out of the reach of chil-

dren and do not allow persons unfamil-

iar with the tool or these instructions to

operate the tool. Tools can be dangerous

in the hands of untrained users.

• Maintain tools. Check for misalignment

or binding of moving parts, breakage

of parts and any other condition that

may affect the tool’s op er ation. If dam-

aged, have the tool repaired before use.

Many accidents are caused by poorly

maintained tools.

• Keep handles dry, clean and free from

oil and grease. Allows for better control

of the tool.

Service

• Have your tool serviced by a qualified

repair person using only identical re-

placement parts. This will ensure that

the safety of the tool is maintained.

Specific Safety

Information

WARNING

This section contains important safety

information that is specific to this tool.

Read these precautions carefully be-

fore using the FlexShaft™ Drain Cleaning

Machine to reduce the risk of electrical

shock or other serious injury.

SAVE ALL WARNINGS

AND INSTRUCTIONS FOR

FUTURE REFERENCE!

Keep this manual with machine for use by

the operator.

K9-12 FlexShaft™ Drain Cleaning Machine

999-995-413.08_REV. E

4

blockage and clean the walls of the pipe. The

K9-12 Drain Cleaning Machine contains an

integral clutch that serves as a cable protection

system. This system reduces the likelihood of

cable damage if the chain knockers become

locked or lodged in a blockage.

FlexShaft Drain Cleaner is well suited to use

with inspection cameras during the drain

cleaning process. The FlexShaft Machine is

lightweight and compact for ease of trans-

port.

Figure 1A – RIDGID® K9-12 FlexShaft Drain

Cleaning Machine

Figure 1B – RIDGID® K9-12 FlexShaft Drain

Cleaning Machine

and breaking of the cable and reduce the

risk of injury.

• Do not wear loose clothing or jewelry.

Keep your hair and clothing away from

moving parts. Loose clothing, jewelry or

hair can be caught in moving parts.

• Do not operate this machine if oper-

ator or machine is standing in water.

Operating machine while in water in-

creases the risk of electrical shock.

• Do not use if there is the risk of con-

tact with other utilities (such as natural

gas or electric) during operation. Visual

inspection of the drain with a camera is

a good practice. Crossbores, improperly

placed utilities and damaged drains could

allow the cutter to contact and damage

the utility. This could cause electrical

shock, gas leaks, fire, explosion or other

serious damage or injury.

• Read and understand these instruc-

tions, the battery drill instructions and

the instructions for any other equip-

ment used with this tool before oper-

ating. Failure to follow all instructions may

result in property damage and/or serious

injury.

RIDGID Contact

Information

If you have any question concerning this

RIDGID® product:

– Contact your local RIDGID distributor.

– Visit RIDGID.com to find your local

RIDGID contact point.

– Contact Ridge Tool Technical Service De-

part ment at ProToolsTechService@

Emerson.com, or in the U.S. and Canada

call 844-789-8665.

Description

The RIDGID® Model K9-12 FlexShaft™ Drain

Cleaning Machine, with proper attachments,

is designed to clean and descale 11/4" to 2"

pipes and drain lines for kitchen and bath

sinks, tub/shower drains, laundry and HVAC

lines.

A user supplied battery powered drill is used

to drive the FlexShaft Drain Cleaning Machine.

The K9-12 FlexShaft Drain Cleaning Machine

cable assembly is manually fed in and out of

the drain. A chain knocker that expands to the

pipe inside diameter is used to break up the

Carry Handle

Cable

Cap

Cable

Assembly

Hex Key

Feet

Input

Shaft

Warning &

Operation

Label

Chain

Knocker

Feet

(Horizontal-

Use Position)

QR Code

Weight/Date

Code Label

(European

Units)

K9-12 FlexShaft™ Drain Cleaning Machine

999-995-413.08_REV. E 5

This machine is made to clean

drains. If properly used, it will not damage a

drain that is in good condition and properly

designed, constructed and maintained. If the

drain is in poor condition, or has not been

properly designed, constructed and main-

tained, the drain cleaning process may not be

effective or could cause damage to the drain.

The best way to determine the condition of

a drain before cleaning is through visual in-

spection with a camera. Improper use of this

drain cleaning machine can damage the drain

cleaning machine and the drain. This machine

may not clear all blockages.

Pre-Operation Inspection

WARNING

Before each use, inspect your Drain

Cleaning Machine and correct any prob-

lems to reduce the risk of serious injury

from electric shock, twisted or broken

cables, chemical burns, infections and

other causes and prevent Drain Cleaning

Machine damage.

Always wear safety glasses, and other

appropriate protective equipment when

inspecting your Drain Cleaning Machine.

1. Clean the machine, including handles

and controls. This aids inspection and

helps prevent the machine or control from

slipping from your grip. Clean and main-

tain the machine per the maintenance

instructions.

2. Inspect the machine for:

•

Proper assembly and completeness.

• Any broken, worn, missing, misaligned

or binding parts.

• Presence and readability of the warning

label (see Figure 2).

• Smooth and free movement of the ca-

ble assembly in and out of the machine.

• Any condition which may prevent safe

and normal operation.

If any problems are found, do not use the

drain cleaning machine until the problems

have been repaired.

Specifications

Drain Capacity

(Nominal) ................ 1-1/4" to 2"

(32 – 50 mm)

Cable Diameter

(without Sheath)… .. 1/4" (6 mm)

Cable Assembly Diameter

(with Sheath) .......... 3/8" (9.5 mm)

Cable Assembly

Length..................... 30' (9 m)

Rotational Speed .... Maximum 2500 RPM

Drill Attachment ...... 5/16" Hex (8 mm)

Integral Clutch ........ Non-Adjustable

Weight (without drill

or knocker) .............. 8.4 lbs. (3.8 kg)

Dimensions

(without drill) ........... 4.8" × 12.9" × 15.1"

(122 mm × 328 mm ×

384 mm)

Operating

Temperature ........... 20°F to 140°F

(-6°C to 60°C)

It is not recommended to clean glass, ce-

ramic, porcelain or similar pipe or fixtures

with the FlexShaft Drain Cleaners as it may

damage the pipe or fixture.

Specifications - Acceptable

Battery Powered Drills

Rotational Speed .... 1800 to 2500 RPM

Chuck Size ............. 3/8” (10 mm) or

greater

Drill Clutch .............. Adjustable

Switch Type ............. Momentary Contact

Switch Lock ............ Not equipped

Drill must carry appropriate certification mark

for the market (CE mark, c()us mark, etc.)

Do not use corded drills, hammer drills or

impact drivers. Use of an inappropriate drill

increases the risk of equipment damage and

personal injury. See Battery Powered Drill

Set-up and Operation section.

Standard Equipment

Refer to the RIDGID catalog for details on

equipment supplied with specific drain clean-

ing machine catalog numbers.

NOTICE

K9-12 FlexShaft™ Drain Cleaning Machine

999-995-413.08_REV. E

6

cation. Do not use the Drain Cleaning

Machine while standing in water.

2. Inspect the drain to be cleaned. If possi-

ble, determine the access point(s) to the

drain, the size(s), length(s), and materi-

al(s) of the drain, distance to mainlines,

the nature of the blockage, presence of

drain cleaning chemicals or other chemi-

cals, etc.

If chemicals are present in the drain, it

is important to understand the specific

safety measures required to work around

those chemicals. Contact the chemical

manufacturer for required information.

Confirm no other utilities are present in

the drain or area to reduce the risk of

damage. Visual inspection of the drain

with a camera is a good practice.

If needed, remove fixture (water closet,

etc.) to allow access to drain. Do not run

the chain knocker in a fixture. This could

damage the FlexShaft Machine or the

fixture.

Best drain cleaning results will occur if

water is flowing during the drain cleaning

process to wash away debris. For 11/4"

and 11/2" sink drains, cut away wall pipes

are available to allow this. See Figure 3

for installation. Place a container to catch

any drain contents that may spill.

Figure 3 – Wall Pipe Installation (Available

accessory)

3. Determine the correct equipment for the

application. See Specifications. Drain

Cleaning Machines for other applications

can be found by consulting the Ridge Tool

Catalog, online at RIDGID.com.

4. Make sure all equipment has been prop-

erly inspected.

5. If needed, place protective covers in the

Figure 2 – Warning Label

3. Clean any debris from the cable assembly

and chain knockers. Inspect sheath for

wear and damage. There should not be

any cuts, kinks, breaks or excessive wear.

Inspect the cable near the chain knocker.

Cable assemblies should not be bent

or deformed. Cable strands should be

tight to one another without separation.

Inspect chain knocker for damage and

wear of the chain itself. If chain links are

worn more than ¼ through or damaged,

replace the chain knocker. Replace worn

and damaged equipment before using

drain cleaning machine.

Confirm that the chain knocker is properly

set up and is secure on the cable.

4. Inspect the battery powered drill per its

instructions. Make sure that the drill is in

good operating condition and the switch

controls the drill operation. Confirm that

the drill meets the requirements in the

Specifications section and is properly set

for use with the machine.

5. Inspect and maintain any other equip-

ment being used per its instructions to

make sure it is functioning properly.

Machine and Work Area

Set-up

WARNING

Set up the Drain Cleaning Machine and

work area according to these proce-

dures to reduce the risk of injury from

electric shock, fire, machine tipping,

twisted or broken cables, chemical

burns, infections and other causes, and

prevent machine damage.

Always wear safety glasses and other

appropriate protective equipment when

setting up your Drain Cleaning Machine.

1. Check for an appropriate work area.

Operate in a clear level, stable, dry lo-

1800-2500

/min

K9-12 FlexShaft™ Drain Cleaning Machine

999-995-413.08_REV. E 7

damage the cable or injure the operator.

Extending the drain back to the Drain

Cleaning Machine also makes it easier to

feed cable assembly into drain.

9. Rotate the cable cap to move the arrow

to unlock position and remove the cap

(Figure 6). Retrieve chain knocker and

cable assembly from the drum. Feed the

chain knocker through the cable cap hole

and lock the cable cap in original position.

(Figure 7).

Figure 6 – Unlock the Cap

Figure 7A –

Remove Cap

Figure 7B –

Retrieve Chain Knocker/Cable

work area. The drain cleaning process

can be messy.

6. Place the Drain Cleaning Machine on the

ground in the horizontal use position, see

Figure 4. Machine should sit squarely and

firmly on the ground. Do not operate with

the machine in the vertical position. This

will reduce the risk of tipping.

7. Remove the battery from the drill. Properly

set-up the drill. (See Battery Powered

Drill Set-up and Operation section.) Se-

curely attach the drill chuck to the hex of

the input shaft (Figure 4).

Figure 4 – Attaching Drill To Input Shaft

Figure 5 – Example of Extending Drain Access

to within 3’ of Machine Cable Outlet

8. Position the Drain Cleaning Machine so

that the cable outlet is within 3' (1 m) of

the drain access. Greater distances from

the drain access increases the risk of the

cable assembly twisting or kinking. If the

FlexShaft Machine cannot be placed with

the cable outlet within 3' (1 m) of the drain

access, extend the drain access with sim-

ilar sized pipe and fittings (see Figure 5).

Improper cable assembly support can

allow the cable to kink and twist and can

Rotation

Arrow

Input

Shaft

Cap Unlock

Position Cap Lock

Position

Cap

Drain

Extension

K9-12 FlexShaft™ Drain Cleaning Machine

999-995-413.08_REV. E

8

the drill before making any adjustments or

attaching to/removing from the drain cleaning

machine.

Drill Switch

The drill must be equipped with a momen-

tary contact switch without a switch lock. This

means that the drill will only turn when the

operator is depressing the drill switch. If the

drill switch is released, the drill will turn OFF.

Set drill rotation to match the arrow on the

machine (see Figure 4).

Drill Speed

When using your FlexShaft Drain Cleaning

Machine, the required rotational speed range

is 1800 – 2500 rpm. Cleaning will be optimized

by rotating the chain knockers closer to the

2500 rpm maximum. To do this, know your bat-

tery powered drill specifications and settings to

optimize operation. Many battery powered drills

have multiple speed settings, and typically the

highest speed is in the range for operation

of the FlexShaft equipment. Do not operate

the FlexShaft drain cleaning machine at over

2500 rpm.

Figure 8 – Example Drill Settings

Drill Adjustable Clutch Setting

Always use a battery powered drill equipped

with a properly set adjustable clutch. The drill

should be used only in the “screw driving

mode” ( ) for the drill adjustable clutch to

work. When the drill adjustable clutch releases,

the motor continues to turn but the drill chuck

Figure 7C – Feed Cable Through Cap Hole

Figure 7 –

Retrieving Chain Knocker From

Drum

10. Pull approximately 4' (1.2 m) of cable as-

sembly out of the machine.

11. Mark the sheath to indicate when the

chain knocker is approaching the drain

opening when withdrawn. This can be

done with tape. This reduces the risk of

the chain knockers coming out of the

drain and whipping around. The distance

depends on the configuration of the drain,

but should be at least 4' (1.2 m) from the

chain knocker.

12. Ensure chain knocker is properly installed

(see Installing/Adjusting Chain Knocker).

13. Insert chain knocker end at least 1' (0.3

m) into drain.

14. Evaluate the work area and determine if

any barriers are needed to keep bystand-

ers away from the drain cleaning machine

and work area. The drain cleaning pro-

cess can be messy, and bystanders can

distract the operator.

15. Position the machine for easy accessibil-

ity. You must be able to hold and control

the cable assembly and the drill switch.

16. With dry hands, insert the battery into the

drill.

Battery Powered Drill

Set-Up and Operation

See the Specifications section along with this

section for information on acceptable battery

powered drills for use with the FlexShaft Drain

Cleaning Machines. There are many types of

battery powered drills available, and not all are

appropriate for use with the FlexShaft Drain

Cleaning Machines. If there is any question

about appropriateness of a drill for this appli-

cation, do not use it. Remove the battery from

Drill Speed Settings Torque Adjustment Collar

K9-12 FlexShaft™ Drain Cleaning Machine

999-995-413.08_REV. E 9

Chain knockers with carbide cutting tips

are used for removing scale from the in-

side of the pipe and can be used for scale

and roots. Carbide cutting tips are used

for aggressive cleaning and could dam-

age pipe, especially softer materials (such

as plastics and Orangeburg), thin walled

pipe, or if the chain knocker is kept in one

position for an extended time. See Figure

10, Attachment Selection Charts.

Figure 9 – Chain Knockers

does not. Many times this is accompanied

by vibration/noise from the drill. When using

the K9-12 FlexShaft Drain Cleaning Machine,

always start with the drill adjustable clutch

set to approximately 25% of the total clutch

adjustment range (example – if the torque

adjustment collar on the drill is marked from 1

to 20, the initial setting should be 5).

Battery powered drills are often also equipped

with “Drill” ( ) and “Hammer” ( ) modes

of operation (Figure 8). In these modes, the

adjustable clutch does not work, and these

modes should never be used for FlexShaft

Drain Cleaning Machine operation.

Operate the drain cleaner per these instruc-

tions with the chain knocker in a drain. The

K9-12 FlexShaft machine integral clutch

should release first before the drill clutch

releases. If during operation the drill clutch

continuously releases (“clutches out”), before

the integral K9-12 FlexShaft Drain Cleaning

Machine clutch, then the drill clutch must be

adjusted. Release the drill switch and remove

the drill from machine. The drill adjustable

clutch setting should be increased. The drill

clutch can be increased in steps until the drill

runs smoothly and no longer releases before

the K9-12 FlexShaft machine integral clutch.

If the integral FlexShaft machine clutch contin-

uously releases, withdraw the cable from the

drain. Review the drain cleaner set up and op-

eration and confirm everything is correct – an

important part of the set up for proper opera-

tion is chain knocker selection and adjustment

(See Figures 10 & 11). Make any needed

changes and continue cleaning drain. If the

integral K9-12 Machine Clutch continues to

disengage during use, consider using another

RIDGID drain cleaning machine.

Installing/Adjusting Chain

Knocker

1. Select proper chain knocker for the con-

ditions.

Chain knockers are sized based on collar

inside diameter and are designed for spe-

cific cable sizes. ¼" chain knockers are

used on ¼" cable, etc. Do not use a larger

size chain knocker on a smaller cable (for

instance 5/16" on ¼"). See Figure 9 and

Collar Distance Chart.

Chain knockers without carbide cutting

tips can be used in common pipe types.

These chain knockers work well in

grease and similar blockages.

1 Chain

2 Chain

K9-12 FlexShaft™ Drain Cleaning Machine

999-995-413.08_REV. E

10

DESCRIPTION

K9-102

1.5" K9-102

2" K9-102

1.5" CARBIDE K9-102

2" CARBIDE

K9-102

1.5"

PENETRATING

HEAD

K9-102

2”

PENETRATING

HEAD

CATALOG NO. 64293 64298 64283 64288 66568 66573

PIPE SIZE

1.25"-1.5"

(32 - 40 mm) 2"

(50 mm) 1.25"-1.5"

(32 - 40 mm) 2"

(50 mm) 1.25"-1.5"

(32 - 40 mm) 2"

(50 mm)

COPPER

GALVANIZED

CAST IRON

PVC

ABS

ORANGEBURG

CORRUGATED

CLAY

GREASE

SOFT

BLOCKAGE

SCALING

LIGHT ROOTS

WIPES

INCLUDED

WITH KIT

BLOCKAGE PIPE TYPE

Chain Knockers Carbide Tipped

Chain Knockers

Figure 10A – Attachment Selection Charts

Penetrating Head

Chain Knockers

All ¼" cable FlexShaft accessories (K9-102) are compatible with the K9-12 FlexShaft Drain Cleaning Machine

K9-12 FlexShaft™ Drain Cleaning Machine

999-995-413.08_REV. E 11

DESCRIPTION

K9-102

NYLON 1.5" K9-102

NYLON 2" K9-102

BALL HEAD K9-102

DROP HEAD

CATALOG NO. 68933

68938 71838 71843

PIPE SIZE 1.5"

(40 mm) 2"

(50 mm) 1.5"

(40 mm) 2"

(50 mm)

COPPER

GALVANIZED

CAST IRON

PVC

ABS

ORANGEBURG

CORRUGATED

CLAY

SPRAY

RELINING

FRAGILE

PIPES/GENTLE

CLEANING

FINAL

CLEANUP

PENETRATES

BLOCKAGES

SMALL LINE

NAVIGATION

DOWN STACK

NAVIGATION

SECURING

RING 68923 68923

APPLICATIONS PIPE TYPE

Nylon Brush Ball/Drop Head

Figure 10B – Attachment Selection Charts

All ¼" cable FlexShaft accessories (K9-102) are compatible

with the K9-12 FlexShaft Drain Cleaning Machine

2. Figure 11 shows a schematic of proper

chain knocker installation and adjustment.

There are two key points when installing/

adjusting chain knockers.

Collar Distance: Set the chain knocker

collars the correct distance apart (“Collar

Distance”) to allow the chains to spread

an appropriate amount when rotated to

clean the pipe walls. Collar Distance var-

ies based on cable size and pipe diam-

eter, and is generally set using a spacer

made from sheath (“Collar Spacer”). If

additional flexibility is required to navigate

a bend, the collar spacer can be removed

and the collar distance can be set with a

tape measure. Operating without a collar

spacer makes it more likely for the cable

to flip over in use and be damaged. Do

not operate carbide cutters without a

collar spacer to reduce risk of cable

damage.

Exposed Cable: Minimize the amount

of exposed cable (cable not covered by

sheath). The more exposed cable there

is, the more likely the cable will flip over

in use and be damaged. Exposed cable

should be limited to no more than ¼" (6

mm), and is set with a bushing made from

sheath (“Knocker Bushing”). Exposed

cable varies with the amount of cable

out of the drum. The more cable out of

the drum, the smaller the exposed cable.

Exposed cable may need to be set with

cable out of the drum for best results,

Sheath is supplied with the drain cleaner

and is available as a service part to allow

configuration as needed for your specific

application. Only use RIDGID FlexShaft

Drain Cleaner sheath of the correct size

for the cable. Any time sheath is cut, it

should be cut cleanly and squarely. Do

not damage the cable when cutting the

sheath.

3. Chain knockers are retained to the cable

with set screws that use a supplied 3 mm

hex key. Loosen set screws and remove

chain knocker, spacer and bushing from

cable.

4. Inspect the sheath end for damage or

wear. The sheath end should be square

and clean. If needed, the sheath end can

be trimmed slightly.

5. If needed, cut a section of sheath to use

as the collar spacer to the appropriate

size (See Collar Distance Chart).

K9-12 FlexShaft™ Drain Cleaning Machine

999-995-413.08_REV. E

12

Installing Brushes

Brushes are available for various uses, such

as cleaning the inside of the pipe, centering

the chain knocker in the pipe and spreading

lining compound. See the specific brush infor-

mation for the types of uses it is appropriate

(See Figure 10B).

Brushes can be assembled in a variety of

configurations, with some options shown in

Figure 12.

Figure 12A – Two Spaced Brushes With A

Chain Knocker In Between

Figure 12B – Two Spaced Brushes

Installation of brushes is similar to the in-

stallation of chain knockers. The collar of the

brush is placed over the cable and retained

by securely tightening the set screws. When

Collar distance can be modified to your

preference for the specific pipe/applica-

tion. As collar distance increases, the di-

ameter of the chains decreases, and vice

versa. Improperly set collar distance can

reduce the efficiency of pipe cleaning.

6. Test fit the chain knocker, knocker bushing

and collar spacer on the cable as shown in

Figure 11. Chains should be straight – do

not assemble with chains twisted. To pre-

vent excessive cable end wear, cable end

should be flush with the end of the collar.

Check length of exposed cable. To reduce

the risk of cable flip over and damage,

exposed cable cannot exceed ¼" (6 mm).

If needed, cut a knocker bushing from

sheath to limit exposed cable. Always use

a knocker bushing to reduce wear on

the sheath end.

7. With the chain knocker correctly installed

on the cable as shown in Figure 11, use

the supplied hex wrench to securely

tighten the collar set screws. Place set

screw tip against cable, then tighten an

additional 1/8 to 1/4 turn (45° to 90° de-

grees). If the set screws are not secure,

the chain knocker could slip and damage

the cable or be lost down the drain.

Cable Number Number of Nominal Recommended Collar

Size of Chains Links/Chain Pipe Size Distance

1/4" 1 7 11/4" to 11/2" (32 mm to 40 mm) 13/4" (44.5 mm)

2 7 11/2" to 2" (40 mm to 50 mm) 13/4" (44.5 mm)

Collar Distance Chart

Knocker

Figure 11 – Chain Knocker Installation/Adjustment

Sheath End

Collar Spacer

Cable

Set Screw

(3 mm Hex)

Sheath

Collar Distance

Knocker Collar

Knocker Chain

Cable End

Flush To

Collar

Carbide Cutting Tip

(If Equipped)

Knocker Bushing Knocker Collar

Set Screw

(3 mm Hex)

Exposed Cable

.25" (6 mm)

Maximum

K9-12 FlexShaft™ Drain Cleaning Machine

999-995-413.08_REV. E 13

at the end of the cable, the cable end is flush

with the brush collar. Brush securing rings

are available to improve brush retention if set

screws loosen in use.

As with chain knockers, minimize the amount

of exposed cable (cable not covered by

sheath). The more exposed cable there is, the

more likely the cable will flip over in use and

be damaged. Limit exposed cable to no more

than ¼" (6 mm), set with a bushing made from

sheath (“Knocker Bushing”).

Installing Penetrating Head

Penetrating heads are available to help create

a hole in a blockage to get the drain flowing

and allow the chain knocker into an area.

See Figure 13 for installation information.

Figure 13 – Penetrating Head Installation

Operating Instructions

WARNING

Always use safety glasses and gloves in good

condition while handling or using. Use latex or

rubber gloves, face shields, protective clothing,

respirators or other appropriate protective equip-

ment when chemicals, bacteria or other toxic or

infectious substances are suspected to be present

to reduce the risk of infections, burns or other

serious personal injury.

Do not use with a corded drill. Operating with a

corded drill increases the risk of electrical shock.

Do not allow the chain knocker/end of cable

to stop turning while drill switch is depressed.

This can overstress the cable and may cause

twisting, kinking or breaking of the cable assembly

and may result in serious personal injury.

Practice good hygiene. Do not eat or smoke

while handling or operating the tool. After han-

dling or operating drain cleaning equipment,

use hot, soapy water to wash hands and other

body parts exposed to drain contents. This

will help reduce the risk of health hazards due to

exposure to toxic or infectious material.

Keep hand on the cable assembly whenever

the FlexShaft Machine is running. This provides

better control of the cable and helps prevent twist-

ing, kinking and breaking of the cable and reduces

the risk of injury.

Position the FlexShaft Machine cable outlet

within 3' (1 m) of the drain inlet or properly sup-

port exposed cable assembly when the dis-

tance exceeds 3' (1 m). Greater distances can

cause control problems leading to twisting, kinking

or breaking of the cable. Twisting, kinking or break-

ing cable may cause striking or crushing injuries.

One person must control both the cable as-

sembly and cordless drill. Do not lock drill switch

in the ON position during operation. If the cable

stops rotating, the operator must be able to re-

lease the drill switch to prevent twisting, kinking

and breaking of the cable and reduce the risk

of injury.

Follow operating instructions to reduce the

risk of injury from twisted or broken cable,

cable ends whipping around, machine tipping,

chemical burns, infections and other causes.

1. Make sure that machine and work area is

properly set-up and that the work area is

free of bystanders and other distractions.

2. Pull cable assembly from the machine and

feed into drain. At least 1' (0.3 m) of cable

must be in drain so that the chain knocker

will not come out of the drain and whip

around when the machine is started.

Directly route the cable assembly from the

machine cable outlet to the drain opening,

minimizing exposed cable and changes

in direction. Do not tightly bend the cable

assembly – this can increase the risk of

twisting or breaking.

If using a camera to view the drain clean-

ing process, the camera can be fed in

at the same time. Typically the cable as-

sembly and the camera push rod can be

gripped and advanced/retrieved at the

same time. Keep the camera at least 1.5’

(0.5 m) behind the chain knocker.

Do not allow the spinning chain

knocker to hit the camera head/push rod.

It can damage it.

3. Assume a proper operating position to

help maintain control of the cable assem-

bly and drill (see Figure 14):

Collar

Securely Tighten

Set Screws

1/4" (6mm) MAX.

Fully Insert

NOTICE

K9-12 FlexShaft™ Drain Cleaning Machine

999-995-413.08_REV. E

14

knocker into the blockage when withdraw-

ing the cable. It’s important to let the

speed of the chain knocker clean the

drain – do not force chain knockers

into blockages.

8. Advancing/Retrieving the Cable

Assembly – FlexShaft Lubricant

In some cases it may be beneficial to

apply RIDGID FlexShaft lubricant to the

outside of the sheath when feeding the

cable down the drain. This can make it

easier to advance the cable assembly

down the drain and allow greater clean-

ing distance. If doing so, place a clean

towel with lubricant on it in the palm of the

gloved hand used for advancing the cable

assembly, and apply lubricant as feeding

the cable assembly (Figure 15). Add lu-

bricant to the towel as needed during the

process.

Only use RIDGID FlexShaft lubricant.

Other lubricants may not be appropriate

for use in a drain and could contaminate

the water.

When retrieving the cable assembly, it is

good practice to use a towel to wipe dirt

and debris from the cable sheath as it is

pulled from the drain and fed back into the

drum.

Figure 15 – Applying Lubricant to the Cable

Sheath

9. Rotating the Chain Knocker

Generally the chain knocker is rotated for

cleaning while withdrawing the cable.

• Be sure you can quickly release the drill

switch.

• Your gloved hand must be on the cable

assembly to control and support as the

cable assembly is fed into the drain and

blockage.

• Be sure that you have good balance, do

not have to overreach, and cannot fall

on machine, drain, etc..

This operating position will help to main-

tain control of the cable assembly and

FlexShaft Machine.

Figure 14 – In Operating Position

4. Confirm that at least 1' (0.3 m) of cable

assembly is in the drain.

5. Confirm that the drill directional switch

is in the forward direction, and depress

and release the drill switch, noting the

direction of the drill chuck. Drill rotation

should match the arrow on the drum (See

Figure 4). Do not rotate the cable in re-

verse except as specifically described in

these instructions. Running in reverse can

damage the FlexShaft cable.

6. Place one hand on the cable assembly

and other hand on the drill grip.

7

. The FlexShaft Drain Cleaning Machine uti-

lizes high rotational speed and low torque

to clean drains. FlexShaft cable assem-

blies are more flexible than other types

of drain cleaning cables. The FlexShaft

machine is best used by applying light

pressure and slowly working the chain

3' (1 m) MAX.

K9-12 FlexShaft™ Drain Cleaning Machine

999-995-413.08_REV. E 15

Only rotate the cable/chain knocker when

the chain knocker is at least 1’ in the drain.

To rotate the cable, firmly grip the drill han-

dle and depress the drill switch. The per-

son controlling the cable assembly must

also control the drill switch. Do not operate

the machine with one person controlling

the cable assembly and another person

controlling the drill. Do not allow cable

assembly to build up outside the drain,

bow or curve. This can lead to twisting,

kinking and breaking of the cable. At any

time, release the drill trigger to stop cable

rotation. When clearing blockages, operate

the cable at full speed for best cleaning.

Do not force the chain knocker into

blockages. In some cases, using variable

speed will assist with navigating turns.

Rotating the chain knocker in FORWARD

or REVERSE for a short time while ad-

vancing the cable assembly can help it

negotiate the drain and blockages.

10. Advance the cable assembly into the drain,

generally not rotating. Grasp the sheath

near where it exits the machine housing.

Pull 6" to 12" (150 to 300 mm) of cable

assembly out of the FlexShaft Machine

so that there is a slight bow in the cable.

Gloved hand must be on cable assembly

to control and support. Improper cable

support can allow the cable assembly to

kink or twist and can damage the cable or

injure the operator. Feed the cable assem-

bly into the drain (Figure 16, Step 1).

11. Continue to advance the cable assem-

bly until the resistance is encountered.

Carefully work the chain knocker through

the blockage. Do not force the cable

assembly – if the chain knocker cannot

turn, it cannot clean the drain. Pay at-

tention to how far the cable has gone. Do

not overrun the cable into a larger drain.

This can cause the cable to knot up or

cause other damage (Figure 16, Step 2).

12. If possible, start a flow of water down the

drain to flush the debris out of the line

and help clean the cable assembly as it is

retrieved. This can be done by turning on a

faucet in the system or other methods. Pay

attention to the water level, as the drain

could plug again (Figure 16, Step 3).

13. With the chain knocker past the blockage/

area to be cleaned, fully depress the drill

switch to rotate the chain knocker. Slowly

pull the cable assembly from the drain, al-

lowing the rotating chain knocker to clean

the drain walls and break up the blockage

The general operating steps for the FlexShaft Drain Cleaning Machines (see below):

1

3

2

4

5

6

1. Advance the chain knocker (generally not

rotating) to the area of the drain that needs

cleaned.

2.

If there is a blockage, pass the chain

knocker through the blockage.

3. If possible, start a flow of water through the

drain to carry cuttings and debris away as

the drain is cleaned.

4. Rotate the cable/chain knocker at full speed.

5. Continue to rotate knocker. Gradually with-

draw the cable assembly so that the chain

knocker can break up the blockage.

6. Continue to gradually withdraw the cable

assembly while rotating so that the chain

knocker can clean the walls of the drain.

Figure 16 – General Operating Steps with Chain Knocker

K9-12 FlexShaft™ Drain Cleaning Machine

999-995-413.08_REV. E

16

(Figure 16, Steps 4 & 5). If the cable

stops turning, do not continue operat-

ing the drill. This may cause the cable to

twist and kink. At any time, release the drill

switch to stop cable rotation.

Monitor the feedback from the feel of the

cable assembly in your hand and the

sound of the drill/knocker in the drain. If

the integral FlexShaft machine clutch or

the drill clutch disengages (indicated by

noise from the integral clutch or drill and

possibly some vibration of the drill), the

cable has likely stopped turning. See Drill

Adjustable Clutch Setting in the Battery

Powered Drill Set-up and Operation sec-

tion. When this happens, release the drill

switch to stop the rotation of the drill. Once

drill rotation is stopped the clutch will auto-

matically reengage, however, if the cable

end is stuck, it must be moved out of the

blockage before proceeding.

It may be necessary to move the chain

knocker out of the blockage to allow it to

come back up to speed.

If the chain knocker becomes stuck, it may

be able to be freed by running the drill in re-

verse for a short time. Do not run in reverse

for more than a few seconds to prevent

cable damage. In some cases, it may be

possible to pull the cable assembly and the

blockage out of the drain by hand. If this is

done, be careful to not damage the cable

assembly. Remove the blockage from the

knocker and cable and continue cleaning

the drain as detailed above.

If using with a camera, do not run the

chain knocker into the camera head or

push rod.

In some cases, to clean the opposite side

of the pipe it may help to run the drill in

REVERSE for a short time.

14. Continue to clean the rest of the drain

while retrieving the cable. Once the drain

has been cleaned, retrieve the cable and

feed back onto the drain cleaning machine.

Pay close attention, as the cable may

lodge in a blockage while being retracted

(Figure 16, Step 6).

15. Watch for your sheath marking as the

cable assembly is retrieved; listen care-

fully to the sound of the knocker as it

approaches the pipe entrance. Release

the drill switch when the chain knocker

nears drain opening. Do not pull the chain

knocker from drain while it is rotating. The

chain knocker can whip around and can

cause damage or serious injury.

16. If needed for complete cleaning, repeat

the above procedure.

17. Pull any remaining cable assembly from

the line by hand and push back into the

drum. Prepare the machine for transport.

Using Machine With Brushes

Using the machine with a brush is similar to

use with a chain knocker. Brushes are used

for finer cleaning of the pipe; they are not

used for blockage removal. Remove block-

ages and heavy debris with a chain knocker

or other methods first. While chain knockers

are most typically rotated while withdrawing

the cable from the drain, brushes are typi-

cally used while advancing the cable. This

is because the brushes typically fill the drain

diameter and push debris in front of them.

See Figure 17 for general steps.

Step 1

Step 2

Step 3

Figure 17 –

Cleaning Drain Walls With Brush

1. Advance the brush (generally not rotating)

into the drain.

2. When close to the area of the drain to be

cleaned, if possible, start a flow of water

through the drain to carry debris away

during cleaning.

3. Rotate the cable/brush at full speed and

gradually advance the cable into the drain

to clean the walls as desired.

Brushes can also be used in conjunction with

chain knockers such as centering devices

or for combined cleaning. Usage depends

K9-12 FlexShaft™ Drain Cleaning Machine

999-995-413.08_REV. E 17

on the exact circumstances and is left to the

judgement of the user.

Penetrating tip heads can also be used with

brushes or chain knockers for additional ac-

cessory customization.

Draining the Drum

If the cable is wiped clean as it is pulled from

the drain, there should be minimal need to

drain the drum. If needed, remove the cable

cap and turn the machine over to drain.

Transportation and

Storage

Feed all of cable assembly and

chain knocker into the drum and secure the

cap. Remove the drill from the input shaft. Do

not leave the drill attached during transport

and storage to prevent tipping and damage to

the drain cleaner.

The Drain Cleaning Machine must be kept

dry and indoors or well covered if kept out-

doors. Store the machine in a locked area

that is out of reach of children and people

unfamiliar with drain cleaning machines.

This machine can cause serious injury in the

hands of untrained users.

Maintenance

Instructions

WARNING

Drill should be removed from drain

cleaner before any maintenance is per-

formed.

Always wear safety glasses and other

appropriate protective equipment when

performing any maintenance.

Cleaning

It is good practice to wipe dirt and debris

from the cable assembly as it is pulled from

the drain to help keep the equipment clean. If

needed, cable assembly can be pulled from

the machine and the housing opened for

flushing/ cleaning.

Clean the machine as needed with hot soapy

water and/or mild disinfectants. Drain the ma-

chine as needed.

Lubrication

The FlexShaft Drain Cleaning Machines are

lubricated for life from the factory.

Cable Assembly Replacement

1. Place the Drain Cleaning Machine in

Horizontal use position.

2. Pull entire cable assembly from housing.

3. Using a Philips-head screwdriver, remove

the fasteners holding the housing together.

Remove the top housing (Figure 18)

Figure 18 – Drain Cleaner Top Housing

Removed

Figure 19 –

Replacement Cable Installation

4. Remove retention plate fasteners and

retention plate (Figure 18).

5. Remove the detent pin from the cable

coupling.

6. Remove the cable coupling from the in-

tegral cable clutch shaft and remove the

cable assembly.

7

. Reverse process to assemble. Fully insert

the cable into the cable channel. There

should be no more than 0.25" (6 mm)

between the end of the sheath and the

coupler (See Figure 19).

8. Securely attach all fasteners. Do not over-

tighten.

WARNING

Cable

Clutch

Retention

Plate

Cable

Channel

Cable

Coupling

Detent

0.25" MAX.

K9-12 FlexShaft™ Drain Cleaning Machine

999-995-413.08_REV. E

18

For a complete listing of RIDGID equipment

avail

able for these tools, see the Ridge Tool

Cata log online at RIDGID.com or see Contact

Information.

Disposal

Parts of these tools contain valuable materi-

als and can be recycled. There are compa-

nies that specialize in recycling that may be

found locally. Dispose of the components in

compliance with all applicable regulations.

Contact your local waste management au-

thority for more information.

Service and Repair

WARNING

Improper service or repair can make

the machine unsafe to operate.

The “Maintenance Instructions” will take care

of most of the service needs of this machine.

Any problems not addressed by this section

should only be handled by a RIDGID Autho-

rized Independent Service Center. Use only

RIDGID service parts.

For information on your nearest RIDGID Au-

thorized In depen dent Service Center or

any service or repair questions see Contact

Information section in this manual.

Optional Equipment

WARNING

To reduce the risk of serious injury, only

use accessories specifically designed

and recommended for use with the

RIDGID K9-12 FlexShaft Drain Cleaning

Machine, such as those listed.

SYMPTOM POSSIBLE REASON SOLUTION

Cable kinking or

breaking.

FlexShaft Machine

wobbles or moves

while cleaning drain.

Troubleshooting

Cable assembly is being forced.

Incorrect FlexShaft Machine or chain

knocker used for pipe diameter.

Drill being run in reverse.

Cable assembly exposed to acid/

corroded.

Cable/sheath worn out.

Cable assembly not properly

supported.

Chain knocker not properly set up/

adjusted.

Improper drill.

Ground not level.

Do no force cable assembly. Follow op-

erating instructions.

Use correct FlexShaft Machine or chain

knocker for pipe size.

Use reverse only if flex shaft gets

caught in pipe.

Clean cable assembly routinely.

Replace worn cable assembly.

Support cable assembly properly, see

instructions.

Properly set up/adjust chain knocker,

see instructions.

Choose proper drill, see instructions.

Place on level stable surface.

Catalog

No. Description

64283 Knocker, 1/4" cable, 11/4"-11/2" pipe, single

chain, carbide tip

64293 Knocker, 1/4" cable, 11/4"-11/2" pipe, single chain

64288 Knocker, 1/4" cable, 2" pipe, 2 chain, carbide tip

64298 Knocker,

1/4" cable, 2" pipe, 2 chain

64338 FlexShaft Lubricant, 8 oz, 12 per case

64363 11/4" RIDGID Wallpipe Accessory

64368 11/2" RIDGID Wallpipe Accessory

71838 Penetrating Ball Head 11/4"- 2"

71843 Penetrating Drop Head 11/4"- 2"

68933 1.5" (40mm) Nylon Brush for 1/4" (6mm) cable

68938 2" (50mm) Nylon Brush for 1/4" (6mm) cable

66568 FlexShaft Chain Knocker, 1/4" cable, 11/4" - 11/2"

pipe, single chain, carbide tipped w/penetrat-

ing head

66573 FlexShaft Chain Knocker, 1/4" cable, 2" pipe, 2

chain, carbide tipped w/penetrating head

76183 FlexShaft Cable Assembly, 1/4" x 30'

64643 FlexShaft

1/4" Sheath Stock, 12"

La page charge ...

RIDGID เครื่องมือทำความสะอาดท่อระบายน้ำรอบผนังท่อ FlexShaft รุ่น K9-12 Manuel utilisateur

Ce manuel convient également à

RIDGID เครื่องมือทำความสะอาดท่อระบายน้ำรอบผนังท่อ FlexShaft รุ่น K9-12 Manuel utilisateur

dans d''autres langues

Documents connexes

Autres documents