Homelite ut80516 Le manuel du propriétaire

Marque: Homelite

Modèle: ut80516

Catégorie: Nettoyeurs haute pression

Taper: Le manuel du propriétaire

SAVE THIS MANUAL FOR FUTURE REFERENCE

Ce nettoyeur haute pression a été conçu et fabriqué conformément

aux strictes normes de fiabilité, simplicité d’emploi et sécurité

d’utilisation. Correctement entretenu, il vous donnera des années

de fonctionnement robuste et sans problème.

AVERTISSEMENT :

Pour réduire les risques de

blessures, l’utilisateur doit lire et veiller à bien comprendre

le manuel d’utilisation avant d’utiliser ce produit.

Merci de votre achat.

Su lavadora de presión ha sido diseñada y fabricada

de conformidad con las estrictas normas para brindar

fiabilidad, facilidad de uso y seguridad para el operador. Con el

debido cuidado, le brindará muchos años de sólido y eficiente

funcionamiento.

ADVERTENCIA: Para reducir el riesgo de lesiones, el

usuario debe leer y comprender el manual del operador antes

de usar este producto.

Le agradecemos su compra.

CONSERVER CE MANUEL POUR

FUTURE RÉFÉRENCE

GUARDE ESTE MANUAL PARA

FUTURAS CONSULTAS

Your pressure washer has been engineered and manufactured to our high standard for dependability, ease of operation,

and operator safety. When properly cared for, it will give you years of rugged, trouble-free performance.

WARNING: To reduce the risk of injury, the user must read and understand the operator’s manual before using

this product.

Thank you for your purchase.

OPERATOR’S MANUAL

MANUEL D’UTILISATION

MANUAL DEL OPERADOR

2200 PSI PRESSURE WASHER

NETTOYEUR HAUTE PRESSION DE 2200 PSI

LAVADORA A PRESIÓN DE 2200 PSI

UT80516

To register your Homelite product, please visit: http://register.homelite.com/

Pour enregistrer votre produit de Homelite, s’il vous plaît la visite: http://register.homelite.com/

Para registrar su producto de Homelite, por favor visita: http://register.homelite.com/

NOTICE AVIS AVISO

Do not use E15 or E85 fuel (or fuel

containing greater than 10% ethanol)

in this product. It is a violation of fed-

eral law and will damage the unit and void your warranty.

Ne pas utiliser d’essence E15 ou E85 (ou un carburant

contenant plus de 10 % d’éthanol) dans ce produit. Une

telle utilisation représente une violation de la loi fédérale et

endommagera l’appareil et annulera la garantie.

No utilice combustibles E15 o E85 (ni combustibles que

contengan más de 10 % de etanol) con este producto. Esto

constituye una violación a la ley federal, dañará la unidad

y anulará la garantía.

A - Pin (goupille, pasador)

B - Button (boulon, botón)

C - Handle lock cap (chapeau de fermeture de la

poignée, tapa de aseguramiento del mango)

Fig. 1a

A - Phillips screwdriver (tournevis phillips,

destornillador phillips)

B - Combination wrench (clé mixte, llave de

combinación)

A - Telescoping handle (poignée télescopique, mango telescópico)

B - Trigger handle (poignée de gâchete, mango del gatillo)

C - Spray wand (lance de pulvérisation , tubo de rociado)

D - High pressure hose storage (rangement de la tuyau haute pression,

almacenamiento del manguera de alta presión)

E - High pressure hose (tuyau haute pression, manguera de alta presión)

F - Trigger with lock out (gâchette avec verrou, gatillo con seguro)

G - (I) ON / (O) OFF switch (interrupteur marche/arrêt, interruptor de

encendido/apagado)

H - Fuel tank (réservoir de carburant, tanque de combustible)

I - Fuel cap (bouchon du réservoir, tapa del tanque de combustible)

J - Recoil starter (poignée du lanceur avec corde, mango del arrancador con

cuerda)

K - Primer bulb (poire d’amorçage, bomba de cebado)

L - Lubricant cap/dipstick (bouchon/jauge d’huile , tapa del aceite con varilla

de nivel)

M - Muffler (silencieux, silenciador)

N - Injection hose with filter (d’injection transparent avec filtre, manguera de

inyección con filtro)

O - Nozzle storage (buses et rangement de buse, boquillas y compartimientos

para boquillas)

Fig. 2

Fig. 3

A - Axle (essieu, eje)

B - Hitch pin (goupille d’attelage, pasador de

enganche)

Fig. 1

See this fold-out section for all of the figures referenced in the operator’s manual.

Consulter l’encart à volets afin d’examiner toutes les figures mentionnées dans le manuel d’utilisation.

Consulte esta sección desplegable para ver todas las figuras a las que se hace referencia en el manual del operador.

Fig. 5

Fig. 6

Fig. 4 Fig. 7 Fig. 10

Fig. 11

A - Collar (collier, collar)

B - Inlet coupler (raccord d’entrée, acoplador de

entrada)

C - High pressure hose (tuyau haute pression,

manguera de alta presión)

A - Lubricant cap/dipstick (bouchon/jauge

d’huile , tapa del aceite con varilla de nivel)

B - Upper fill level (supérieur remplir le niveau

nivel de carga superior)

C - Funnel (entonnoir, embudo)

Fig. 8

Fig. 9

A - Water intake (rise d’eau, entrada de agua)

B - Screen (tamis, cedazo)

C - Garden hose (tuyau d’arrosage, manguera de

jardín)

A - Injection hose fitting (raccord du flexible

d’injection, adaptador de la manguera de

inyección)

B - Injection hose (flexible d’injection, manguera

de inyección)

X 3

A - High pressure hose (tuyau haute pression,

manguera de alta presión)

B - Collar (collier, collarín)

C - Threaded nipple (têton fileté, conexión

roscada

)

A - Fuel cap (bouchon du réservoir, tapa del

tanque de combustible)

B - Funnel (entonnoir, embudo)

A - Trigger handle (poignée de gâchete, mango

del gatillo)

B - Spray wand (lance de pulvérisation , tubo de

rociado)

C - Connector (connecteur, conector)

A - Primer bulb (poire d’amorçage,bomba de

cebado)

B - (I) ON / (O) OFF switch (interrupteur marche/

arrêt, interruptor de encendido/apagado)

iii

Fig. 12

Fig. 13

Fig. 14

Fig. 17

Fig. 18

Fig. 19

Fig. 15

Fig. 16

A - Paper clip (pièces de papier, clips de papel)

A - Air filter latch (verrou du filtre à air, traba del

filtro de aire)

B - Air filter cover (couvercle du filtre à air, tapa

del filtro de aire)

C - Air filter (filtre à air, filtro de aire)

D - Tabs (ergots, legüetas)

E - Notches (encoche, ranuras)

A - Recoil starter (lanceur à rappel, arrancador

retráctil)

A - Lock-out (erouillage, seguro)

B - Slot (fente, ranura)

MOVING tHE prEssurE wAsHEr

DÉpLAcEMENt DE LA MAcHINE

pArA MOVEr LA MáquINA

A - Injection hose (flexible d’injection, manguera

de inyección)

B - Detergent container (réservoir de détergent,

recipiente del detergente)

0.028 in. - 0.031 in.

(0,71 mm - 0.78 mm)

A - Nozzle (embout, boquilla)

B - “Click” (déclic, hasta que trabe)

C - Quick-connect collar (casquillo de conexión

rápida)

D - Spray wand (lance de pulvérisation, tubo de

rociador)

E - Pull back the quick-connect collar (tirer la

bague à connexion rapide, tire del collar de

conexión rápida)

F - Push the nozzle into place (insérer en place la

buse, introduzca la boquilla en su lugar)

G - Push the collar forward (poussez en avant la

bague, empuje del collar adelante)

Fig. 21

tO stOrE tHE MAcHINE

rEMIsAGE DE LA MAcHINE

pArA GuArDAr LA MáquINA

Fig. 20

A - Oil drain plug (bouchon de vidange d’huile, tapón de drenaje del aceite)

C - Container (récipient, recipiente)

Page 2 — English

 Introduction ......................................................................................................................................................................2

Introduction / Introducción

 Important Safety Instructions ........................................................................................................................................... 3

Règles de sécurité générales / Reglas de seguridad generales

 Specific Safety Rules ........................................................................................................................................................ 4

Règles de sécurité particulières / Reglas de seguridad específicas

Symbols ......................................................................................................................................................................... 5-6

Symboles / Símbolos

 Features ............................................................................................................................................................................7

Caractéristiques / Características

 Assembly .......................................................................................................................................................................7-9

Assemblage / Armado

 Operation ................................................................................................................................................................... 10-13

Utilisation / Funcionamiento

 Maintenance ..............................................................................................................................................................14-16

Entretien / Mantenimiento

 Troubleshooting .............................................................................................................................................................. 17

Dépannage / Solución de problemas

 Warranty ....................................................................................................................................................................18-19

Garantie / Garantía

 Parts Ordering and Service ...............................................................................................................................Back Page

Commande de pièces et réparation / Pedidos de piezas y servicio ......................................................... Page arrière / Pág. posterior

This product has many features for making its use more pleasant and enjoyable. Safety, performance, and dependability

have been given top priority in the design of this product making it easy to maintain and operate.

* * *

Ce produit offre de nombreuses fonctions destinées à rendre son utilisation plus plaisante et satisfaisante. Lors de la

conception de ce produit, l’accent a été mis sur la sécurité, les performances et la fiabilité, afin d’en faire un outil facile à

utiliser et à entretenir.

* * *

Este producto ofrece numerosas características para hacer más agradable y placentero su uso. En el diseño de este producto

se ha conferido prioridad a la seguridad, el desempeño y la fiabilidad, por lo cual se facilita su manejo y mantenimiento.

TABLE OF CONTENTS

TABLE DES MATIÈRES / ÍNDICE DE CONTENIDO

INTRODUCTION

INTRODUCTION / INTRODUCCIÓN

Page 3 — English

IMPORTANT SAFETY INSTRUCTIONS

WARNING:

Read and understand all instructions. Failure to follow

all instructions listed below may result in electric shock,

fire and/or carbon monoxide poisoning which will cause

death or serious personal injury.

READ ALL INSTRUCTIONS

 Know your tool. Read the operator’s manual carefully.

Learn the machine’s applications and limitations as well

as the specific potential hazards related to this tool.

Keep guards in place and in working order. Never oper-

ate the tool with any guard or cover removed. Make sure

all guards are operating properly before each use.

 Remove adjusting keys and wrenches. Form habit of

checking to see that keys and adjusting wrenches are

removed from tool before turning it on.

 To reduce the risk of injury, keep children and visitors

away. All visitors should wear safety glasses and be kept

a safe distance from work area.

Keep the area of operation clear of all persons,

particularly small children, and pets.

Do not start or operate the engine in a confined space,

building, near open windows, or in other unventilated

space where dangerous carbon monoxide fumes can

collect. Carbon monoxide, a colorless, odorless, and

extremely dangerous gas, can cause unconsciousness

or death.

 Use right tool. Don’t force tool or attachment to do a

job it was not designed for. Don’t use it for a purpose not

intended.

 Dress properly. Do not wear loose clothing, gloves,

neckties, or jewelry. They can get caught and draw you

into moving parts. Rubber gloves and nonskid footwear

are recommended when working outdoors. Also wear

protective hair covering to contain long hair.

Do not operate the equipment while barefoot or when

wearing sandals or similar lightweight footwear. Wear

protective footwear that will protect your feet and improve

your footing on slippery surfaces.

Exercise caution to avoid slipping or falling.

 Always wear eye protection with side shields marked

to comply with ANSI Z87.1. Following this rule will re-

duce the risk of serious personal injury.

 Don’t overreach or stand on unstable support. Keep

proper footing and balance at all times.

 Use only recommended accessories. The use of

improper accessories may cause risk of injury.

 Follow the maintenance instructions specified in this

manual.

 Check damaged parts. Before further use of the

tool, a

guard or other part that is damaged should be carefully

checked to determine that it will operate properly and

perform its intended function. Check for alignment of

moving parts, binding of moving parts, breakage of parts,

mounting, and any other conditions that may affect its

operation. A guard or other part that is damaged must

be properly repaired or replaced by an authorized service

center to avoid risk of personal injury.

 Never leave tool running unattended. Turn power off.

Don’t leave tool until it comes to a complete stop.

Keep the engine free of grass, leaves, or grease to

reduce the chance of a fire hazard.

 Keep the exhaust pipe free of foreign objects.

Follow manufacturer’s recommendations for safe

loading, unloading, transport, and storage of

machine.

 Be thoroughly familiar with controls. Know how to stop

the product and bleed pressure quickly.

 Keep tool dry, clean, and free from lubricant and

grease. Always use a clean cloth when cleaning. Never use

brake fluids, gasoline, petroleum-based products, or any

solvents to clean tool.

 Stay alert and exercise control. Watch what you are

doing and use common sense. Do not operate tool when

you are tired. Do not rush.

Do not operate the product while under the influence

of drugs, alcohol, or any medication.

Check the work area before each use. Remove all

objects such as rocks, broken glass, nails, wire, or string

which can be thrown or become entangled in the

machine.

Do not use tool if switch does not turn it off. Have

defective switches replaced by an authorized service

center.

Before cleaning, repairing, or inspecting, shut off the

engine and make certain all moving parts have stopped.

Disconnect the spark plug wire, and keep the wire away

from the plug to prevent accidental starting.

 Avoid dangerous environment. Don’t use in damp or

wet locations or expose to rain. Keep work area well

lit.

 Never use in an explosive atmosphere. Normal

sparking of the motor could ignite fumes.

Do not operature while smoking or near an open

flame.

Do not operate around dry brush, twigs, cloth rags, or

other flammable materials.

 WARNING: Risk of injection or injury – Do not direct

discharge stream at persons.

Page 4 — English

SPECIFIC SAFETY RULES

 Use caution when positioning the pressure washer for

use. Warm air from the engine could cause discolored

spots on grass.

 Never direct a water stream toward people or pets,

or any electrical device.

Before starting any cleaning operation, close doors

and windows. Clear the area to be cleaned of debris,

toys, outdoor furniture, or other objects that could create

a hazard.

Never pick up or carry a machine while the engine is

running.

 Never start the machine if ice has formed in any part

of the equipment.

 Do not use acids, alkalines, solvents, flammable

material, bleaches, or industrial grade solutions

in this product. These products can cause physical

injuries to the operator and irreversible damage to the

machine.

 Always operate the machine on a level surface. If the

engine is on an incline, it could seize due to improper

lubrication (even at the maximum lubricant level).

 WARNING: High pressure jets can be dangerous

if subject to misuse. The jet must not be directed at

persons, animals, electrical devices, or the machine

itself.

Hold the handle and wand securely with both hands.

Expect the trigger handle to move when the trigger is

pulled due to reaction forces. Failure to do so could cause

loss of control and injury to yourself and others.

Never attempt to make any adjustments while the

engine (motor) is running (except where specifically

recommended by the manufacturer).

 Protective covers must always cover rotating parts

when the engine is running.

Keep cooling air intake (recoil starter area) and muffler

side of the engine at least 3 feet away from buildings,

obstructions, and other combustible objects.

Keep the engine away from flammables and other

hazardous materials.

Keep away from hot parts. The muffler and other engine

parts become very hot; use caution.

Do not touch the spark plug and ignition cable when

starting and operating the engine.

 Check fuel hoses and joints for looseness and fuel

leakage before each use.

 Check bolts and nuts for looseness before each use.

A loose bolt or nut may cause serious engine problems.

Always refuel outdoors. Never refuel indoors or in a

poorly ventilated area.

Never store the machine with fuel in the fuel tank

inside a building where ignition sources are present,

such as hot water and space heaters, clothes dryers,

and the like.

If the fuel tank has to be drained, do this outdoors.

To reduce the risk of fire and burn injury, handle fuel

with care. It is highly flammable.

Do not smoke while handling fuel.

Add fuel before starting the engine. Never remove the

cap of the fuel tank or add fuel while the engine is running

or when the engine is hot.

Loosen fuel cap slowly to release pressure and to keep

fuel from escaping around the cap.

Replace all fuel tank and container caps securely.

Wipe spilled fuel from the unit. Move 30 feet away from

refueling site before starting engine.

If fuel is spilled, do not attempt to start the engine but

move the machine away from the area of spillage and

avoid creating any source of ignition until fuel vapors

have dissipated.

Never attempt to burn off spilled fuel under any

circumstances.

Before storing, allow the engine to cool and drain fuel

from the unit.

Store fuel in a cool, well-ventilated area, safely away

from spark and/or flame-producing equipment.

Store fuel in containers specifically designed for this

purpose.

Empty fuel tank and restrain the unit from moving

before transporting in a vehicle.

When servicing use only identical replacement parts.

Use of any other parts may create a hazard or cause

product damage.

ONLY use cold water.

Make sure minimum clearance of 3 feet is maintained

from combustible materials.

Never spray close to the surface to be cleaned as you

can damage the surface.

After stopping the engine, always pull the trigger on

the trigger handle to relieve stored pressure in the

high pressure hose. Failure to do so could result in seri-

ous personal injury.

For outdoor use only.

Ensure the high pressure hose is properly connected

before using the product.

Save these instructions. Refer to them frequently and

use them to instruct other users. If you loan someone this

tool, loan them these instructions also.

Page 5 — English

SYMBOLS

Some of the following symbols may be used on this product. Please study them and learn their meaning for safe

operation of this product.

SYMBOL NAME EXPLANATION

Safety Alert Indicates a potential personal injury hazard.

Read Operator’s Manual

To reduce the risk of injury, user must read and understand

operator’s manual before using this product.

Eye Protection

Always wear eye protection with side shields marked to comply

with ANSI Z87.1.

Wet Conditions Alert Do not expose to rain or use in damp locations.

Hot Surface

To reduce the risk of injury or damage, avoid contact with any

hot surface.

Risk of Injections

To reduce the risk of injection or injury, never direct a water

stream towards people or pets or place any body part in the

stream. Leaking hoses and fittings are also capable of causing

injection injury. Do not hold hoses or fittings.

Risk of Explosion

Fuel and its vapors are explosive and can cause severe burns

or death.

Risk of Fire

Fuel and its vapors are extremely flammable and explosive. Fire

can cause severe burns or death.

The following signal words and meanings are intended to explain the levels of risk associated with this product.

SYMBOL SIGNAL MEANING

DANGER:

Indicates an imminently hazardous situation, which, if not avoided, will result

in death or serious injury.

WARNING:

Indicates a potentially hazardous situation, which, if not avoided, could result

in death or serious injury.

CAUTION:

Indicates a potentially hazardous situation, which, if not avoided, may result in

minor or moderate injury.

NOTICE:

(Without Safety Alert Symbol) Indicates important information not related to an

injury hazard, such as a situation that may result in property damage.

Page 6 — English

SYMBOLS

Some of the following symbols may be used on this product. Please study them and learn their meaning for safe

operation of this product.

SYMBOL NAME EXPLANATION

Toxic Fumes

Gas products emit carbon monoxide, an odorless, colorless,

poison gas. Breathing carbon monoxide can cause nausea,

fainting, or death.

Kickback

To reduce the risk of injury from kickback, hold the spray wand

securely with both hands when the machine is on.

Electric Shock

Failure to use in dry conditions and to observe safe practices

can result in electric shock.

Chemical Burns

To reduce the risk of injury or damage, DO NOT USE ACIDS,

ALKALINES, BLEACHES, SOLVENTS, FLAMMABLE MATERIAL,

OR INDUSTRIAL GRADE SOLUTIONS in this product.

Page 7 — English

FEATURES

PRODUCT SPECIFICATIONS

Fuel Tank Capacity .................................................................................................................................................... 0.25 gal.

Oil Fill Volume .......................................................................................................................................................16 to 18 oz.

Replacement Spark Plug .......................................................................................................................... F6TC or equivalent

Maximum Pounds Per Square Inch Pressure* .........................................................................................................2,200 psi

Maximum Gallons Per Minute* ...................................................................................................................................2.0 gpm

Maximum Inlet Water Temperature ................................................................................................................................104˚F

*Max. rating determined by PWMA Standard 101

KNOW YOUR PRESSURE WASHER

See Figure 1.

The safe use of this product requires an understanding of

the information on the tool and in this operator’s manual as

well as a knowledge of the project you are attempting. Before

use of this product, familiarize yourself with all operating

features and safety rules.

FUEL TANK

This fuel tank has a maximum capacity of 0.25 gal. Use

unleaded automotive gasoline in the engine.

HOSE STORAGE

Once the high pressure hose is rolled, hang it on the machine

using the hook-and-loop strap to secure in place.

ON/OFF SWITCH

To turn the engine off, press the ON/OFF switch.

RECOIL STARTER

The recoil starter is pulled to start the machine.

THERMAL RELIEF VALVE

This pump feature will prevent water temperatures from

reaching harmful levels by releasing a small amount of

water. Once the water has drained, the thermal relief valve

will reset itself.

TRIGGER HANDLE

The trigger handle has a gripping surface that provides

added control of the spray wand and helps reduce fatigue.

Both the trigger handle and spray wand have storage areas

located on the sides of the machine.

TRIGGER WITH LOCK OUT

Pulling the trigger releases a stream of water for high

pressure cleaning. The lock out provides protection against

unauthorized use.

ASSEMBLY

UNPACKING

This product requires assembly.

 Carefully remove the product and any accessories from

the box. Make sure that all items listed in the packing list

are included.

WARNING:

Do not use this product if any parts on the Packing List

are already assembled to your product when you unpack

it. Parts on this list are not assembled to the product by

the manufacturer and require customer installation. Use

of a product that may have been improperly assembled

could result in serious personal injury.

NOTE: This tool is heavy. To avoid back injury, lift with

your legs, not your back, and get help when needed.

 Inspect the tool carefully to make sure no breakage or

damage occurred during shipping.

 Do not discard the packing material until you have care-

fully inspected and satisfactorily operated the tool.

 If any parts are damaged or missing, please call

1-800-242-4672 for assistance.

Page 8 — English

PACKING LIST

Pressure Washer

25 ft. High Pressure Hose

Trigger Handle

Spray Wand

Quick-Connect Nozzles (3) with Nozzle Storage

Injection Hose

Wheel (2)

Axle (2)

Hitch Pin (2)

4-Cycle Engine Lubricant (SAE 30)

Telescoping Handle

Operator’s Manual

WARNING:

If any parts are damaged or missing do not operate this

product until the parts are replaced. Use of this product

with damaged or missing parts could result in serious

personal injury.

WARNING:

Do not attempt to modify this product or create acces-

sories not recommended for use with this product. Any

such alteration or modification is misuse and could result

in a hazardous condition leading to possible serious

personal injury.

WARNING:

To prevent accidental starting that could cause serious

personal injury, always disconnect the engine spark plug

wire from the spark plug when assembling parts.

TOOLS NEEDED

See Figure 1a.

The following tools (not included or drawn to scale) are

needed for assembly:

 7/16 in. wrench

 Phillips head screwdriver

ATTACHING THE WHEEL ASSEMBLY

See Figure 2.

 Locate the axle, hitch pins, and wheels. Remove the hitch

pin from the axle.

 Slide the axle through the hole in the center of the wheel.

 Lift the machine and slide the combination into the wheel

mounting hole in the machine base as shown.

 Push the hitch pin into the hole on the end of the axle to

secure the wheel assembly.

NOTE: The hitch pin should be pushed into the axle until

the center of the pin rests on top of the axle.

 Repeat with the second wheel.

INSTALLING THE TELESCOPING HANDLE

See Figure 3.

 Align the arrows on the U-shaped handle with the arrows

on the back of the frame.

 Push and hold the button on the handle as you slide the

handle into the holes in the frame.

 Lock the handle in place by aligning the slot in the handle

lock cap with the pin on the housing bar. Next, push the

handle lock cap down while turning the cap clockwise.

NOTE: Before use, pull the handle up until the lock

button snaps through the locking slot to secure the

handle in place.

ATTACHING DETERGENT INJECTION HOSE

See Figure 4.

Before detergent can be used with this machine, the deter-

gent injection hose must be attached.

 Push the open end of the clear detergent injection hose

securely over the fitting as shown.

NOTE: Keep injection hose away from hot surfaces.

 Place the filtered end of the hose in the bottle of detergent.

ASSEMBLING THE SPRAY WAND TO THE

TRIGGER HANDLE

See Figure 5.

 Place the threaded end of the spray wand in the connec-

tor on the end of the trigger handle.

 Turn the connector clockwise until it stops. This secures

the spray wand in place.

 When not in use, remove the spray wand from the trigger

handle by turning the connector counterclockwise. When

not in use, store each piece in the storage area on the

sides of the pressure washer frame.

ASSEMBLY

Page 9 — English

ASSEMBLY

CONNECTING HIGH PRESSURE HOSE TO

TRIGGER HANDLE ASSEMBLY

See Figure 6.

 Screw the collar on the high pressure hose into the trigger

handle’s inlet coupler by turning the hose collar clockwise.

Tighten securely.

NOTE: Be careful to avoid cross-threading, which can

cause the trigger handle to leak during use.

 Pull on the hose to be certain it is properly secured.

CONNECTING THE HIGH PRESSURE HOSE TO

THE PUMP

See Figure 7.

Completely uncoil and straighten the high pressure hose

to prevent kinks.

NOTE: See Using The High Pressure Hose in Operation

for more information about using the high pressure hose.

 Align the collar on the threaded nipple on the pump.

 Insert the nozzle on the end of the high pressure hose

collar into the threaded nipple.

 Turn the collar clockwise to tighten the hose securely to

the pump.

NOTE: Be careful to avoid cross-threading, which can

cause the hose to leak during use.

 Pull on the hose to be certain it is properly secured.

CONNECTING THE GARDEN HOSE TO THE

PRESSURE WASHER

See Figure 8.

NOTICE:

Always observe all local regulations when connnecting

hoses to the water main. Some areas have restrictions

against connecting directly to public drinking water sup-

ply to prevent the feedback of chemicals into the drinking

water supply. Direct connection through a receiver tank

or backflow preventer is usually permitted.

The water supply must come from a water main. NEVER

use hot water or water from pools, lakes, etc. Before

connecting the garden hose to the pressure washer:

 Run water through the hose for 30 seconds to clean any

debris from the hose.

 Inspect the screen in the water intake.

 If the screen is damaged, do not use the machine until

the screen has been replaced.

 If the screen is dirty, clean it before connecting the garden

hose to the machine.

To connect the garden hose to the machine:

Completely uncoil and straighten the high pressure hose

to prevent kinks.

NOTE: There must be a minimum of 10 feet of

unrestricted hose between the pressure washer intake and

the hose faucet or shut off valve (such as a “Y” shut off

connector).

 With the hose faucet turned completely off, attach the

end of the garden hose to the water intake. Tighten by

hand.

NOTICE:

Do not run the pressure washer pump without water sup-

ply connected and turned on, as this may damage the

high pressure seals and decrease pump life. Completely

unwind the hose from its reel or coil and make sure the

hose is not being restricted by tires, rocks, or any other

objects that may lessen or prevent water flow to the

pressure washer.

DO NOT OVERTILT THE UNIT!

Page 10 — English

WARNING:

Do not allow familiarity with this product to make you

careless. Remember that a careless fraction of a second is

sufficient to inflict serious injury.

WARNING:

Always wear eye protection with side shields marked to

comply with ANSI Z87.1. Failure to do so could result in

objects being thrown into your eyes resulting in possible

serious injury.

WARNING:

Do not use any attachments or accessories not recom-

mended by the manufacturer of this product. The use of

attachments or accessories not recommended can result

in serious personal injury.

WARNING:

Never direct a water stream toward people or pets, or

any electrical device. Failure to heed this warning could

result in serious injury.

APPLICATIONS

You may use this tool around the house for cleaning most

small to large horizontal or vertical exterior surfaces, smaller

exterior objects and structures, and outdoor equipment and

tools.* You can:

Clean or remove mold and mildew from weathered decks,

driveways, patios, walkways, sidewalks, etc.

Remove dirt from various exterior vertical surfaces such

as house exteriors, siding, fences, brick, concrete or stone

walls, etc.

Wash boats, outdoor furniture, powered or non-powered

garden equipment, gutters, window screens, grills, play-

ground equipment, etc.

*Always test in an inconspicuous area first.

OPERATION

ADDING LUBRICANT TO THE ENGINE

See Figure 9.

NOTE: This machine has been shipped with approximately

2 oz. of lubricant in the engine from testing. You must add

lubricant to the engine before starting it the first time.

NOTICE:

Any attempt to start the engine without adding lubricant

will result in engine failure.

 Place pressure washer on a flat, level surface. Do not tilt.

 Unscrew the lubricant cap / dipstick by turning counter-

clockwise.

 Using 4-stroke engine lubricant (SAE 30 or SAE 10W30),

add engine lubricant until the fluid level rises to the up-

per portion of the hatched area on the dipstick (18 oz.,

4-cycle engine lubricant provided). Do not overfill.

 Replace the lubricant cap / dipstick and securely tighten.

NOTICE:

Do not overfill. Overfilling the crankcase may cause ex-

cessive smoke and engine damage.

OXYGENATED FUELS

NOTICE:

Do not use E15 or E85 fuel (or fuel containing greater

than 10% ethanol) in this product. It is a violation of

federal law and will damage the unit and void your

warranty.

Fuel system damage or performance problems resulting

from the use of an oxygenated fuel containing more than

the percentage of oxygenates stated below are not covered

under warranty.

Ethanol. Gasoline containing up to 10% ethanol by volume

(commonly referred to as E10) is acceptable. E15 and E85

are not.

Page 11 — English

OPERATION

ADDING GASOLINE TO THE FUEL TANK

See Figure 10.

WARNING:

Gasoline and its vapors are highly flammable and

explosive. To prevent serious personal injury and prop-

erty damage, handle gasoline with care. Keep away from

ignition sources, handle outdoors only, do not smoke

while adding fuel, and wipe up spills immediately.

When adding gas to the pressure washer, make sure the unit

is sitting on a flat, level surface. If the engine is hot, let the

pressure washer cool before adding gas. ALWAYS fill the

fuel tank outdoors with the machine turned off.

NOTE: This is a 4-cycle engine. DO NOT mix fuel and

lubricant together.

 Mix fuel stabilizer with gasoline according to fuel stabilizer

manufacturer’s directions.

 Before removing the fuel cap, clean the area around it.

Remove the fuel cap.

 Insert a clean funnel into the fuel tank then slowly

pour gasoline into the tank. Fill tank to approximately

1-1/2 in. below the top of the tank neck (this allows for

fuel expansion).

 Replace fuel cap and tighten.

 Clean up any spills before starting the engine.

WARNING:

Always shut off engine before fueling. Never add fuel to

a machine with a running or hot engine. Move at least

30 ft. from refueling site before starting engine. Do not

smoke and stay away from open flames and sparks!

Failure to follow these instructions could result in serious

personal injury.

STARTING AND STOPPING THE PRESSURE

WASHER

See Figures 11 - 12.

NOTICE:

Do not run the pressure washer pump without water sup-

ply connected and turned on, as this may damage the

high pressure seals and decrease pump life. Completely

unwind the hose from its reel or coil and make sure the

hose is not being restricted by tires, rocks, or any other

objects that may lessen or prevent water flow to the

pressure washer.

Before starting the engine:

Connect all hoses.

Check all fluids (lubricant and gas).

Turn on the garden hose then squeeze the trigger to

relieve air pressure; hold the trigger until a steady stream

of water appears.

NOTE: Make sure the faucet is turned on fully and that

there are no kinks or leaks in the hose.

To start the engine:

Push primer bulb 3 times.

NOTE: If starting the engine for the first time, push the

primer bulb 5 times.

Put the ON/OFF switch in the ON position.

Grasp the recoil starter and pull slowly until resistance is

felt. Give the recoil starter a short, brisk pull to start the

engine.

NOTE: Do not allow the recoil starter to snap back after

starting; return it gently to its original place.

NOTICE:

If the engine does not start after each pull of the recoil

starter, squeeze the trigger to relieve water pressure

before attempting to start the engine again.

To stop the engine:

Put the ON/OFF (I/O) switch in the OFF position.

Shut off the water supply and pull trigger to release

water pressure.

 WARNING:

While operating and storing, keep at least 3 feet of clear-

ance on all sides of this product, including overhead.

Allow a minimum of 30 minutes of “cool down” time be-

fore storage. Heat created by muffler and exhaust gases

may be hot enough to cause serious burns and/or ignite

combustible objects.

Page 12 — English

OPERATION

USING THE SPRAY WAND TRIGGER

See Figure 13.

For greater control and safety, keep both hands on the

trigger handle at all times.

 Pull back and hold the trigger to operate the pressure

washer.

 Release the trigger to stop the flow of water through the

nozzle.

To engage the lock out:

 Push up on the lock out until it clicks into the slot.

To disengage the lock out:

 Push the lock out down and into its original position.

To use the spray wand, start with the nozzle 1-2 ft. away

from the cleaning surface. Carefully approach the surface

just until the desired level of cleaning is achieved. If the spray

is too close it can damage the cleaning surface.

SELECTING THE RIGHT QUICK-CONNECT

NOZZLE FOR THE JOB

See Figure 14.

Before starting any cleaning job, determine the best nozzle

for the job. Each of the three nozzles has a different spray

pattern. The nozzle patterns are: 0˚ (high pressure), 25˚ (me-

dium pressure), and detergent (low pressure).

Nozzle Application

0º Red Spot cleaning of high, hard-to-reach areas

• Removing caked-on mud from heavy con-

struction, farm, or lawn equipment

• Cleaning tar, glue, or stubborn stains from

concrete

• Cleaning overhead areas

• Removing rust from steel and oxidation

from aluminum

25º Green For general purpose or large surfaces

• General cleaning of dirt, mud, and grime

• Cleaning roofs, gutters, and downspouts

• Removing light mildew stains

• Removing algae and bacteria build-up from

pools

• Rinsing surfaces in preparation for painting

Soap

(Black)

For all detergent applications and for gentle

rinse

NOTE: For a gentle rinse, select the detergent nozzle.

Scouring the surface requires a more direct spray of water.

Select the 0˚ nozzle for tough jobs. Apply detergent using

the detergent nozzle.

WARNING:

NEVER change nozzles or spray patterns without lock-

ing the lock out on the trigger handle and NEVER point

the wand at your face or at others. The quick-connect

feature contains small springs that could eject the nozzle

with some force. Failure to heed this may cause personal

injury.

To connect a nozzle to the trigger handle:

 Turn off the pressure washer and shut off the water

supply. Pull trigger to release water pressure.

 Engage the lock out on the trigger handle by pushing up

on the lock out until it clicks into the slot.

 Pull back the quick-connect collar.

 Push the nozzle into place in the spray wand.

 Push the collar forward so that the nozzle is secured

properly. Check to see that the nozzle is secure.

To disconnect a nozzle from the trigger handle once the

cleaning job is complete:

Turn off the pressure washer and shut off the water

supply. Pull trigger to release water pressure.

 Engage the lock out on the trigger handle by pushing up

on the lock out until it clicks into the slot.

 Remove the nozzle by placing hand over nozzle then

pulling back the quick-connect collar. Place nozzle in the

nozzle storage area on the top of the spray wand.

USING THE HIGH PRESSURE HOSE

The high pressure hose features an outer covering that pro-

vides strength to the hose. If the outer covering becomes

damaged, the hose must be replaced immediately. Do not

use a high pressure hose if the outer covering is damaged.

To prevent damage to the outer covering:

 Inspect the hose before every use.

 Fully unwrap and straighten hose before use.

 Do not allow the high pressure hose to be kinked.

 Keep hose away from hot surfaces and sharp edges.

 Do not pull unit by high pressure hose.

 Do not allow hose to be crushed or wrapped around

objects.

Page 13 — English

OPERATION

MOVING THE PRESSURE WASHER

See Figure 15.

NOTE: Never lift or carry this product using the moving

handle.

 Turn the pressure washer off.

 Standing at the back of the machine, grasp the handle

firmly with both hands and pull the handle up until it locks

into place with a “click”.

 Tilt the machine toward you slightly until it balances on

the wheels then roll the machine to the desired position.

Do not tilt forward or sideways when moving.

 DO NOT attempt to move the unit by pulling on any of

the hoses.

WASHING WITH DETERGENT

See Figure 16.

Use only detergents designed for pressure washers; house-

hold detergents, acids, alkalines, bleaches, solvents, flam-

mable material, or industrial grade solutions can damage

the pump. Many detergents may require mixing prior to use.

Prepare cleaning solution as instructed on the solution bottle.

Always test in an inconspicuous area before beginning.

 Place the detergent injection hose in the bottom of the

detergent bottle / container.

 Install the black nozzle on the spray wand.

 Squeeze the trigger and wait approximately 5 seconds

for the detergent to appear.

 Spray the detergent on a dry surface using long, even,

overlapping strokes. To prevent streaking, do not allow

detergent to dry on the surface.

Before shutting off the engine:

 Place the detergent injection hose in a bucket of clean

water.

 Flush for 1 - 2 minutes (spray clear water through the spray

wand).

 Shut off the engine.

NOTE: Shutting OFF ( O ) the engine will not relieve pressure

in the system. Pull trigger to release water pressure.

RINSING WITH THE PRESSURE WASHER

Turn off the pressure washer and shut off the water

supply. Pull trigger to release water pressure.

 Engage the lock out on the wand by pushing up on the

lock out until it clicks into the slot.

 Pull back and hold the collar.

 Remove the nozzle by pulling it from the collar.

 Select the right nozzle for the job:

• Use lower pressure nozzle (green) to wash items such

as a car or boat.

• Use higher pressure nozzle for jobs such as stripping

paint and degreasing the driveway. When using these

nozzles, test a small area first to avoid surface damage.

 Start at the top of the area to be rinsed and work down,

overlapping the strokes.

HIGH ALTITUDE OPERATION

Specific modifications are needed for high-altitude operation.

Please contact your authorized service center for important

information regarding these modifications. Operating this

engine without the proper altitude modification may increase

the engine’s emissions and decrease fuel economy and

performance.

Page 14 — English

MAINTENANCE

WARNING:

When servicing, use only identical replacement parts.

Use of any other parts could create a hazard or cause

product damage.

WARNING:

Always wear eye protection with side shields marked to

comply with ANSI Z87.1. Failure to do so could result in

objects being thrown into your eyes resulting in possible

serious injury.

WARNING:

Before inspecting, cleaning or servicing the machine, shut

off engine, wait for all moving parts to stop, and discon-

nect spark plug wire and move it away from spark plug.

Failure to follow these instructions can result in serious

personal injury or property damage.

GENERAL MAINTENANCE

Avoid using solvents when cleaning plastic parts. Most

plastics are susceptible to damage from various types of

commercial solvents and may be damaged by their use.

Use clean cloths to remove dirt, dust, lubricant, grease, etc.

WARNING:

Do not at any time let brake fluids, gasoline, petroleum-

based products, penetrating lubricants, etc., come in con-

tact with plastic parts. Chemicals can damage, weaken or

destroy plastic which could result in serious personal

injury.

Only the parts shown on the parts list are intended to be

repaired or replaced by the customer. All other parts should

be replaced at an authorized service center.

Before running the engine, perform the following pre-

operation steps:

Check that all bolts, nuts, etc., are securely tightened.

Make sure the air filter is clean.

Check both the engine lubricant level and the fuel tank

level; refill as needed.

Inspect the work area for hazards.

If there is excessive noise or vibration, stop the unit

immediately.

CLEANING THE AIR FILTER

See Figure 17.

A dirty air filter will cause starting difficulty, loss of

performance, and shorten the life span of the engine. Check

the air filter monthly. For best performance, replace the air

filter at least once a year.

NOTE: DO NOT remove the shroud as you could disconnect

or loosen the wire connecting the OFF switch to the engine

making it inoperable.

Press in on the latch to open the cover.

Remove the air filter cover.

Lift the edge of the air filter carefully and pull it out.

Wash the air filter with warm, soapy water.

Rinse and squeeze to dry.

Put small amount of engine lubricant (SAE 30) on the filter

sponge. Squeeze out the excess lubricant then reinstall

the air filter.

NOTE: Make sure the filter is seated properly inside the

cover. Installing the filter incorrectly will allow dirt to enter

the engine, causing rapid engine wear.

To reinstall the air filter cover, insert the tabs into the

notches. Close the cover and push the latch until it snaps

into place.

NOZZLE MAINTENANCE

See Figure 18.

Excessive pump pressure (a pulsing sensation felt while

squeezing the trigger) may be the result of a clogged or

dirty nozzle.

Turn off the pressure washer and shut off the water

supply. Pull trigger to release water pressure.

Remove the nozzle from the spray wand.

NOTE: Never point the spray wand at your face.

Using a straightened paper clip or nozzle cleaning tool

(not provided), free any foreign materials clogging or

restricting the nozzle.

Using a garden hose, flush debris out of nozzle by back

flushing (running the water through the nozzle backwards

or from the outside to the inside).

Reconnect the nozzle to the spray wand.

Turn on the water supply and start the engine.

CHECKING SPARK PLUG

See Figure 19.

Clean the area around the base of the spark plug before

removing to keep dirt and debris out of the engine. Re-

move spark plug.

Clean off carbon deposits on the spark plug electrode us-

ing a plug cleaner or wire brush. Replace the plug if worn.

For replacement spark plug, see Product Specifications

earlier in this manual or the accompanying engine manual,

if applicable.

Check electrode gap. The gap should be .028 in. - .031 in.

(0.70- 0.80 mm). Adjust the gap, if necessary, by carefully

bending the ground electrode.

Reinstall spark plug. Tighten securely.

Page 15 — English

MAINTENANCE

CHANGING ENGINE LUBRICANT

See Figure 20.

Shut off the engine.

Clean the area around the lubricant drain plug, then re-

move the plug.

Tilt the pressure washer on its side as shown. Drain lu-

bricant into approved container.

NOTE: Drain the lubricant while the engine is still warm

but not hot. Warm lubricant will drain quickly and more

completely.

After the crankcase is completely drained, return the

pressure washer to an upright position.

Replace the lubricant drain plug.

Fill with lubricant following the instructions in Adding Lu-

bricant To The Engine earlier in this manual. For amount

of lubricant needed to refill, see Product Specifications

earlier in this manual or the accompanying engine manual,

if applicable.

NOTE: Consult hazardous waste management guidelines in

your area for the proper way to dispose of used lubricant.

PUMP LUBRICATION

The pump on this product was lubricated with a sufficient

amount of high grade lubricant for the life of the unit under

normal operating conditions. Therefore, no further lubrica-

tion is required.

STORING THE PRESSURE WASHER

See Figure 21.

NOTE: Regular use of fuel stabilizer and pump protector

will give you better performance of the unit and increase

the life of the pump. See the Replacement Parts List for

available sizes and part numbers of these items and call

customer service to order.

Allow 30 minutes of “cool down” time before storing the

machine. Store in a dry, covered area where the weather

can’t damage it.

It is important to store this product in a frost-free area. Always

empty water from all hoses, the pump, and the detergent

bucket before storing.

Drain the fuel tank completely by running the pressure

washer until the gas runs out. Stored gas can go stale in

30 days.

NOTE: Make sure the water supply is connected and

turned on when allowing the pressure washer engine to

run.

 Make sure the on/off switch and fuel valve are in the OFF

position.

 Disconnect the water connection.

Empty the pump by pulling on the starter grip and rope

about 6 times. This should remove most of the liquid from

the pump.

NOTICE:

The use of a pump protector is strongly recommended

after each use and before storing to prevent cold weather

and seal damage during storage.

Drain the lubricant and replace with fresh, clean lubricant

as described in the engine manual.

Disconnect spark plug wire and remove the spark plug.

Pour about a teaspoon of clean, air-cooled, four-cycle

oil through the spark plug hole into the combustion

chamber.

Leaving the spark plug out, pull the starter cord two or

three times to coat the inside of the cylinder wall.

Inspect the spark plug and clean or replace, as necessary.

Reinstall the spark plug, but leave the spark plug wire

disconnected.

Clean the air filter.

Extend the recoil starter rope to check its condition. If

the rope is frayed, have it replaced immediately by an

authorized service center.

Remove all hoses. Coil the hoses and store as shown.

Do not allow the hose to become kinked.

 Store the unit and accessories in an area that does not

reach freezing temperatures. Do not store near furnace or

other sources of heat that could dry out the pump seals.

PREPARING FOR USE AFTER STORAGE

Pull the recoil starter three or four times to clean lubricant

from the combustion chamber.

Remove spark plug from the cylinder. Wipe lubricant from

the spark plug and return it to the cylinder.

Reconnect the spark plug wire.

Refuel the machine as described earlier in the operator’s

manual.

Page 16 — English

Maintenance Items

Perform at every indicated

month or operating hour interval,

whichever comes first

Before

Each Use

First

month or

5 hours

Every

3 months

or 25 hours

Every

6 months

or 50 hours

Every

Year or

100 hours

Every

2 years or

250 hours

Check and refill engine lubricant

•

Change engine lubricant *

• •

Check air filter

•

Clean air filter

•

Replace air filter

•

Check and adjust spark plug

•

Replace spark plug

•

PERIODIC MAINTENANCE SCHEDULE

*Change engine oil every 25 hours when used under heavy load or in high ambient temperature. Dispose of waste lubricant safely and responsibly.

Do not pour into sewage drains, onto garden soil or into open streams. Your local zoning or environmental regulations will give you more detailed

instructions on proper disposal.

Maintenance items not listed here should be performed by a service center.

MAINTENANCE

La page charge ...

Homelite ut80516 Le manuel du propriétaire

Marque: Homelite

Modèle: ut80516

Catégorie: Nettoyeurs haute pression

Taper: Le manuel du propriétaire

Télécharger le PDF

rapport

dans d''autres langues

English: Homelite ut80516 Owner's manual
español: Homelite ut80516 El manual del propietario

Homelite ut80516 Le manuel du propriétaire

Homelite ut80516 Le manuel du propriétaire

dans d''autres langues

Documents connexes

Autres documents