Denon DP-300F Manuel utilisateur

DP-300F
Denon
Marque
Denon
Modèle
DP-300F
Catégorie
Platines audio
Taper
Manuel utilisateur
TURNTABLE
DP-300F
OPERATING INSTRUCTIONS
MODE D’EMPLOI
INSTRUCCIONES DE FUNCIONAMIENTO
ENGLISH
I
n
SAFETY PRECAUTIONS
• LocationofCautionLabels:Bottom
CAUTION
RISK OF ELECTRIC SHOCK
DO NOT OPEN
CAUTION:
TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE
COVER (OR BACK). NO USER-SERVICEABLE PARTS INSIDE.
REFERSERVICINGTOQUALIFIEDSERVICEPERSONNEL.
The lightning flash with arrowhead symbol, within an equilateral
triangle, is intended to alert the user to the presence of
uninsulated “dangerous voltage” within the product’s enclosure
that may be of sufficient magnitude to constitute a risk of electric
shock to persons.
The exclamation point within an equilateral triangle is intended
to alert the user to the presence of important operating
and maintenance (servicing) instructions in the literature
accompanying the appliance.
WARNING:
TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT
EXPOSETHISAPPLIANCETORAINORMOISTURE.
IMPORTANT SAFETY
INSTRUCTIONS
1. Read these instructions.
2. Keep these instructions.
3. Heed all warnings.
4. Follow all instructions.
5. Do not use this apparatus near water.
6. Clean only with dry cloth.
7. Do not block any ventilation openings.
Install in accordance with the manufacturer's instructions.
8. Do not install near any heat sources such as radiators, heat registers, stoves,
or other apparatus (including amplifiers) that produce heat.
9. Do not defeat the safety purpose of the polarized or grounding-type plug. A
polarized plug has two blades with one wider than the other. A grounding
type plug has two blades and a third grounding prong. The wide blade or the
third prong are provided for your safety. If the provided plug does not fit into
your outlet, consult an electrician for replacement of the obsolete outlet.
10. Protect the power cord from being walked on or pinched particularly at
plugs, convenience receptacles, and the point where they exit from the
apparatus.
11. Only use attachments/accessories specified by the manufacturer.
12. Use only with the cart, stand, tripod, bracket, or table
specified by the manufacturer, or sold with the apparatus.
When a cart is used, use caution when moving the cart/
apparatus combination to avoid injury from tip-over.
13. Unplug this apparatus during lightning storms or when
unused for long periods of time.
14. Refer all servicing to qualified service personnel.
Servicing is required when the apparatus has been damaged in any way,
such as power-supply cord or plug is damaged, liquid has been spilled or
objects have fallen into the apparatus, the apparatus has been exposed to
rain or moisture, does not operate normally, or has been dropped.
CAUTION
RISK OF ELECTRIC SHOCK
DO NOT OPEN
FRANCAIS ESPAÑOL
FCCINFORMATION(ForUScustomers)
1.PRODUCT
This product complies with Part 15 of the FCC Rules. Operation is subject
to the following two conditions: (1) this product may not cause harmful
interference, and (2) this product must accept any interference received,
including interference that may cause undesired operation.
2.IMPORTANTNOTICE:DONOTMODIFYTHISPRODUCT
This product, when installed as indicated in the instructions contained
in this manual, meets FCC requirements. Modification not expressly
approved by DENON may void your authority, granted by the FCC, to use
the product.
3.NOTE
This product has been tested and found to comply with the limits for
a Class B digital device, pursuant to Part 15 of the FCC Rules. These
limits are designed to provide reasonable protection against harmful
interference in a residential installation.
This product generates, uses and can radiate radio frequency energy and,
if not installed and used in accordance with the instructions, may cause
harmful interference to radio communications. However, there is no
guarantee that interference will not occur in a particular installation. If this
product does cause harmful interference to radio or television reception,
which can be determined by turning the product OFF and ON, the user
is encouraged to try to correct the interference by one or more of the
following measures:
•Reorientorrelocatethereceivingantenna.
•Increasetheseparationbetweentheequipmentandreceiver.
•Connect the product into an outlet on a circuit different from that to
which the receiver is connected.
•Consultthelocalretailerauthorizedtodistributethistypeofproductor
an experienced radio/TV technician for help.
This Class B digital apparatus complies with Canadian ICES-003.
Cet appareil numérique de la classe B est conforme à la norme NMB-003 du
Canada.
1.DP-300F_E3_安全規格ページ.indd 1 2012/03/15 18:47:36
ENGLISH
II
n
NOTESONUSE/OBSERVATIONSRELATIVESAL’UTILISATION/NOTASSOBREELUSO
WARNINGS AVERTISSEMENTS ADVERTENCIAS
•Avoid high temperatures.
Allow for sufficient heat dispersion when installed in
a rack.
•Handle the power cord carefully.
Hold the plug when unplugging the cord.
•Keep the unit free from moisture, water, and dust.
•Unplug the power cord when not using the unit for
long periods of time.
•Do not obstruct the ventilation holes.
•Do not let foreign objects into the unit.
•Do not let insecticides, benzene, and thinner come
in contact with the unit.
•Never disassemble or modify the unit in any way.
•Ventilation should not be impeded by covering
the ventilation openings with items, such as
newspapers, tablecloths or curtains.
•Naked flame sources such as lighted candles
should not be placed on the unit.
•Observe and follow local regulations regarding
battery disposal.
•Do not expose the unit to dripping or splashing
fluids.
•Do not place objects filled with liquids, such as
vases, on the unit.
•Do not handle the mains cord with wet hands.
•When the switch is in the OFF (STANDBY)
position, the equipment is not completely switched
off from MAINS.
•The equipment shall be installed near the
power supply so that the power supply is easily
accessible.
•Eviter des températures élevées.
Tenir compte d’une dispersion de chaleur
suffisante lors de l’installation sur une étagère.
•Manipuler le cordon d’alimentation avec
précaution.
Tenir la prise lors du débranchement du cordon.
•Protéger l’appareil contre l’humidité, l’eau et la
poussière.
•Débrancher le cordon d’alimentation lorsque
l’appareil n’est pas utilisé pendant de longues
périodes.
•Ne pas obstruer les trous d’aération.
•Ne pas laisser des objets étrangers dans l’appareil.
•Ne pas mettre en contact des insecticides, du
benzène et un diluant avec l’appareil.
•Ne jamais démonter ou modifier l’appareil d’une
manière ou d’une autre.
•Ne pas recouvrir les orifices de ventilation avec des
objets tels que des journaux, nappes ou rideaux.
Cela entraverait la ventilation.
•Ne jamais placer de flamme nue sur l'appareil,
notamment des bougies allumées.
•Veillez à respecter les lois en vigueur lorsque vous
jetez les piles usagées.
•L’appareil ne doit pas être exposé à l’eau ou à
l’humidité.
•Ne pas poser d’objet contenant du liquide, par
exemple un vase, sur l’appareil.
•Ne pas manipuler le cordon d’alimentation avec les
mains mouillées.
•Lorsque l’interrupteur est sur la position OFF
(STANDBY), l’appareil n’est pas complètement
déconnecté du SECTEUR (MAINS).
•L’appareil sera installé près de la source
d’alimentation, de sorte que cette dernière soit
facilement accessible.
•Evite altas temperaturas.
Permite la suficiente dispersión del calor cuando
está instalado en la consola.
•Maneje el cordón de energía con cuidado.
Sostenga el enchufe cuando desconecte el cordón
de energía.
•Mantenga el equipo libre de humedad, agua y
polvo.
•Desconecte el cordón de energía cuando no utilice
el equipo por mucho tiempo.
•No obstruya los orificios de ventilación.
•No deje objetos extraños dentro del equipo.
•No permita el contacto de insecticidas, gasolina y
diluyentes con el equipo.
•Nunca desarme o modifique el equipo de ninguna
manera.
•La ventilación no debe quedar obstruida por
haberse cubierto las aperturas con objetos como
periódicos, manteles o cortinas.
•No deberán colocarse sobre el aparato fuentes
inflamables sin protección, como velas encendidas.
•A la hora de deshacerse de las pilas, respete la
normativa para el cuidado del medio ambiente.
•No exponer el aparato al goteo o salpicaduras
cuando se utilice.
•No colocar sobre el aparato objetos llenos de
líquido, como jarros.
•No maneje el cable de alimentación con las manos
mojadas.
•Cuando el interruptor está en la posición OFF
(STANDBY), el equipo no está completamente
desconectado de la alimentación MAINS.
•El equipo se instalará cerca de la fuente de
alimentación de manera que resulte fácil acceder
a ella.
FRANCAISESPAÑOL
CAUTION:
To completely disconnect this product from the mains, disconnect
the plug from the wall socket outlet.
The mains plug is used to completely interrupt the power supply to
the unit and must be within easy access by the user.
PRECAUTION:
Pour déconnecter complètement ce produit du courant secteur,
débranchez la prise de la prise murale.
La prise secteur est utilisée pour couper complètement
l’alimentation de l’appareil et l’utilisateur doit pouvoir y accéder
facilement.
PRECAUCIÓN:
Para desconectar completamente este producto de la alimentación
eléctrica, desconecte el enchufe del enchufe de la pared.
El enchufe de la alimentación eléctrica se utiliza para interrumpir por
completo el suministro de alimentación eléctrica a la unidad y debe
de encontrarse en un lugar al que el usuario tenga fácil acceso.
1.DP-300F_E3_安全規格ページ.indd 2 2015/01/19 12:47:36
1
Getting Started
ENGLISH
Contents
Getting Started
Thank you very much for purchasing the DENON turntable.
Please read the operating instructions thoroughly in order to acquaint yourself with the turntable system and achieve maximum
satisfaction from it.
Before using
···················································································1
Accessories
····················································································1
About the equalizer switch
··························································2
Assembly
························································································2
Mounting the turntable
·································································2
Mounting the counterweight
························································2
Mounting the head shell with cartridge
········································2
Mounting the dust cover
······························································2
Adjustments
···················································································3
Stylus pressure and anti-skating adjustment
································3
Part names and functions
·····························································4
Starting playback using the auto play function
·························5
Starting playback manually
·························································5
Stopping playback in the middle of a record
·····························5
Replacing the stylus
······································································6
Replacing the cartridge
·································································6
Getting Started
Operation
Accessories
Before using
Pay attention to the following before using this unit:
• Power requirements
Power requirements for electrical equipment differ from area to
area. Please ensure that your machine meets the power
requirements in your area.
If it doubt, consult a qualified electrician.
Check that the following parts are attached in addition to the main
unit:
q Operating instructions ............................................................1
w Warranty .................................................................................1
e Service station list ..................................................................1
r Turntable (with belt)................................................................1
t Turntable sheet.......................................................................1
y Adapter for 45 rpm records....................................................1
u Head shell with cartridge........................................................1
i Dust cover ..............................................................................1
o Counterweight........................................................................1
!0 Hinges.....................................................................................2
!1 Spare lead wire.......................................................................1
rty
ui
o!0
Connections
...................................................................................4
ENGLISH
• About the power switch
This turntable is not equipped with a primary power switch. The
power switch is incorporated in the tone arm of the turntable. The
power to the turntable is cut when the tone arm returns to the tone
arm rest. Note however, that the power is not completely turned off
in this case. If you wish to completely turn the power off,
disconnect the power supply cord from the household AC outlet.
• Protect the turntable too
• Never touch the plug with wet hands.
• Always pull out by the plug and never the cable.
• Only let a qualified professional repair or reassemble the turntable.
An unauthorized person might touch the internal parts and receive
a serious electric shock.
• Never allow a child to put anything, especially metal, into the
turntable.
• What you should know to protect yourself
• Use only a household AC power source. Never use a DC power
source.
• If water is spilled on the turntable, disconnect it and call your
dealer.
• Make sure that the turntable is well ventilated and away from
direct sunlight.
•To avoid damage to the internal circuits and the external surface,
keep it away from heat (stoves, etc.).
•Avoid using spray type insecticide near the turntable it can
damage the finish and might ignite suddenly.
•To avoid damaging the finish, never use paint thinner or other
similar chemicals to clean the turntable.
• Place the turntable on a flat and solid surface.
• If you don’t plan to use the turntable for a long period of time,
disconnect the power supply cord.
•To protect the insulators, always lift the turntable when you move
it. And before moving the turntable, disconnect all the connecting
cables.
•When transporting the turntable over a long distance, place it in its
original box wrapped in protective wrappers.
• Moving the unit
To prevent short-circuits or damaged wires in the connection
cables, always unplug the power supply cord and disconnect the
connection cables between all other audio components when
moving the unit.
• Before turning the power switch on
Check once again that all connections are correct and that there are
not problems with the connection cables. Always set the power
switch to the standby position before connecting and disconnecting
connection cables.
• Store these instructions in a safe place.
After reading, store this instructions along with the warranty card in
a safe place.
• Note that the illustrations in these instructions may differ from
the actual unit for explanation purposes.
Troubleshooting
·············································································7
Specifications
·················································································7
Others
2
Getting Started Getting Started
ENGLISH
Turntable sheet
Square hole
Turntable
Ribbon tape
Counterweight
Tone arm
Lock nut
Head shell with
cartridgeCenter spindle
Twist tie for
clamping
the tone arm
Stylus pressure
adjustment ring
Roller
Belt
Ribbon tape
Square hole
Equalizer
switch
Hinge retainer
section
Holder
Dust
cover
Hinge
Cabinet
• The equalizer switch is set to the “ON” position upon shipment
from the factory. Be sure to check before mounting the turntable
and turntable sheet.
• The sound may be extremely weak or distorted if the equalizer
switch is not properly set.
Assembly
Mount the turntable on the center spindle.
1
Turn the turntable so that the rolleris visible through
the square hole with the ribbon tape for catching the
belt.
2
Pinch the ribbon tape and catch the belt on the outer
center of the roller.
• Remove the ribbon tape once the belt is caught.
•Turn turntable slowly 5 or 6 turns. The belt is caught at the
center of the roller.
3
Mount the turntable sheet.
4
Mounting the turntable
Mounting the counterweight
Insert the counterweight onto the shaft at the back of the
tone arm and screw it in.
Mount with the stylus pressure adjustment ring towards the
front.
Mounting the head shell with cartridge
Insert the head shell with cartridge onto the tone arm
and fasten it in place with the lock nut ( page 6).
Insert the 2 included hinges securely into the holders
at the back of the cabinet.
1
Mount the hinge retainer sections of the dust cover
onto the hinges.
• Insert fully in the direction of the arrow.
•When removing the dust cover, open the dust cover fully then
pull out in the direction opposite the arrow.
2
• Hold the dust cover near the hinge retainer sections when mounting
and removing it.
Once assembly is finished, remove the twist tie for
clamping the tone arm.
OFF:
When connecting to the PHONO input terminal
(The record player’s equalizer cannot be used.)
ON:
When connecting a terminal other than the PHONO input terminal
(The record player’s equalizer can be used.)
This record player comes with a built-in equalizer.
Switch as shown below according to the terminal being used.
Mounting the dust cover
ENGLISH
About the equalizer switch
NOTE:
• Do not remove the twist tie for clamping the tone arm until
assembly is completed.
• Do not connect the power supply cord until assembly is
completed.
3
Getting Started Getting Started
ENGLISH
Adjustments
Turn the power off when making the adjustments.
Counterweight
Lifter lever
Armrest
Tone arm
Cartridge
Turntable
Stylus pressure
adjustment ring
Anti-skating knob
NOTE:
• Be very careful not to damage the stylus tip on the turntable
sheet, etc.
Set the anti-skating knob to “0”.
1
Lower the lifter lever and move the tone arm over the
turntable.
For cartridges with removable stylus covers, remove the stylus
cover.
2
Balance the tone arm.
• Move the counterweight forward or backward so that the tone
arm is parallel to the turntable surface when you are not
touching it.
3
Set the tone arm back on the armrest.
4
Holding the counterweight with a finger so that it
does not move, turn the stylus pressure adjustment
ring so that it’s “0” mark is lined up with the center
line of the tone arm’s rear shaft.
5
Turntable surface Tone arm Counterweight
(Weight too far to the back)
(Weight too far to the front)
Counterweight
Center line
Stylus pressure
adjustment ring
A
Turn the counterweight in the direction of arrow “A”
and set to the appropriate stylus pressure for the
cartridge.
The appropriate stylus pressure for the included cartridge is 2.0
g (19.6 mN). Set to “2”.
6
Turn the anti-skating knob and set to the same value
as for the cartridge’s stylus pressure.
• The proper anti-skating value can be achieved.
7
Stylus pressure and anti-skating adjustment
Setting reference point
ENGLISH
4
ENGLISH
Getting Started
Part names and functions
!1
i
o
y
t
r
!2
!3!4
u
e
w
q
!0
Connections
R
L
PHONO IN
Pre-main amplifier
R
L
• If the player starts operating when the power supply cord is plugged in, press the STOP button.
q START button ·············································(5)
•Starts playback.
w STOP button ···············································(5)
• Stops playback.
e Finger catch
r Lock nut ··················································(2, 7)
t Armrest
y SIZE button (£ 17 / ¢ 30)······················(5)
• Set according to the size of the record to be
played (11 ft/30 cm or 6 ft/17 cm).
u SPEED button (£ 45 / ¢ 33) ··················(5)
• Set according to the speed (revolutions per
minute) of the record to be played.
i Lifter lever···················································(3)
o Anti-skating knob·······································(3)
!0 Stylus pressure adjustment ring ··············(3)
!1 Counterweight············································(3)
!2 Dust cover···················································(2)
!3 Equalizer switch ·········································(2)
!4 Dust cover hinge ········································(2)
AC 120 V, 60 Hz
Power outlet
NOTE:
•Turn off the power of the device to which the record player is being connected. Do not plug the
record player’s power plug into a power outlet until all connections are finished.
• Check that all connections are proper, then plug the record player’s power plug into the AC outlet on
the amplifier or into a household AC power outlet.
¢ When connecting to the PHONO input terminal
Equalizer switch : OFF ( page 2)
R
L
AUDIO IN
(AUX IN)
Pre-main amplifier
or
audio system
R
L
¢ When connecting a terminal other than the PHONO input terminal
Equalizer switch : ON ( page 2)
Pin-plug cable
(length: approx. 3 ft/1.0 m)
AC 120 V, 60 Hz
Power outlet
For details on the functions of these parts, refer to the pages given in parentheses ( ).
ENGLISH
5
Operation
ENGLISH
Operation
Lifter lever
SPEED
SIZE
Armrest
Tone arm
Finger catch
STOP
START
Turntable
¢ Opening the stylus cover
Raise the stylus cover before starting playback.
Place the record on the turntable.
For EP (“doughnut”) records, use the 45 rpm adapter.
1
Set the record’s playing speed using SPEED.
For 33 1/3 records ...........................Set to ¢ 33
For 45 records .................................Set to £ 45
2
Set the record size using SIZE.
For 30 cm records ...........................Set to ¢ 30 cm
For 17 cm records ...........................Set to £ 17 cm
3
Press START and hold it in for about 1 second.
• The turntable starts turning and playback starts automatically.
• Once the record is played, the tone arm returns to its original
position and the turntable automatically stops turning.
4
• Once you have finished playing records, lower the stylus cover to
protect the stylus tip.
• This set has an “auto return” function by which the tone arm
automatically returns to its original position once a specific point is
reached after a record finishes playing. Though there is no problem
with records of normal size, with records including grooves up to
this point, the auto return function may be activated before playback
is finished.
NOTE:
• Do not touch the tone arm or turntable or turn off the power
while a record is playing.
• The auto play system cannot be used for 9 ft/25 cm records.
In this case operate manually. If the tone arm does not return to
its original position after playback stops, press STOP.
Place the record on the turntable.
For EP (“doughnut”) records, use the 45 rpm adapter.
1
Set the record’s playing speed using SPEED.
For 33 1/3 records ...........................Set to ¢ 33
For 45 records .................................Set to £ 45
2
Raise the lifter lever and holding the head shell’s
finger catch move the tone arm to the beginning of
the selection you want to play.
3
Lower the lifter lever.
• The tone arm lowers the stylus tip slowly onto the record and
playback starts.
4
NOTE:
•Be careful not to scratch the record.
Press STOP.
• Playback stops and the tone arm returns to its original position.
It is also possible to stop playback by raising the lifter lever. In
this case lift it using the head shell’s finger catch and move the
tone arm back to the arm rest.
ENGLISH
Starting playback using the auto play function Starting playback manually
Stopping playback in the middle of a record
Playback
position
Position when not in use
Stylus cover
Cartridge
6
Operation Operation
ENGLISH
The included stylus has a service life of about 400 hours. To avoid
damaging valuable records, replace the stylus without delay.
Purchase a replacement stylus at the store where you purchased the
record player or your nearest repair and inquiry outlet. Specify that you
want the “DSN-85” replacement stylus exclusively for the DP-300F.
q
w
¢ Removing the replaceable stylus
Holding the cartridge steady with one hand, grasp the replaceable
stylus with the other hand, push down in the direction of arrow q,
then pull the stylus off gently in the direction of arrow w.
Cartridge
q
w
¢ Mounting the replaceable stylus
Holding the cartridge steady with one hand, grasp the replaceable
stylus with the other hand, point the catch on the replaceable
stylus in the direction of arrow q, insert it all the way into the long
hole in the cartridge, then push up in the direction of arrow w until
a click is heard.
• Before replacing the stylus, turn off the amplifier’s power and
unplug the player’s power supply cord.
• The stylus tip is an extremely delicate part, so handle it very
carefully. Use a soft brush to gently remove any dust from the stylus
tip.
• Removing the head shell makes it easy to replace the stylus.
If you wish to mount a different cartridge on this player, use one
weighing about 44 to 93 mN (about 4.5 to 9.5 g).
To purchase a head shell only, ask for a “PCL-310BK” exclusively for
the DP-300F at your store of purchase or nearest repair and inquiry
outlet.
¢ Removing the cartridge
1. Turn the head shell lock nut in the direction of the arrow and
remove the head shell.
2. Remove the cartridge mount screws.
3. Disconnect the lead wires on the cartridge side.
Lock nut
Head shell
Cartridge mount screw
Washer
Lead wire
Cartridge
Nut
¢ Mounting the cartridge
1. Connect the lead wires. They are color-coded as shown below. Be
careful to connect them properly.
RED .........................Right channel (R)
WHITE .....................Left channel (L)
GREEN.....................Right channel ground (RG)
BLUE .......................Left channel ground (LG)
2. To achieve the required overhang, mount in such a way that the
stylus tip is positioned about 1 ft/45 mm from the edge of the head
shell’s mount surface (the rubber washer), as shown on the
diagram below. (The overhang for this player should be 0.75 ft/19
mm.)
• After replacing the cartridge, do not forget to readjust the horizontal
balance, stylus pressure, and anti-skating value ( page 3).
• The thickness of the terminal depends on the replacement cartridge,
and some may not connect securely. In this case, use the included
spare lead wire.
1 ft/
45 mm
(Back side of head shell)
Mount parallel.
(Front side of head shell)
Mount perpendicular.
(Backside of cartridge)
Above
(RED) R
(GREEN) RG
(WHITE) L
(BLUE) LG
ENGLISH
Replacing the stylus Replacing the cartridge
Symptom
7
ENGLISH
If a problem should arise, first check the following.
1. Are the connections correct?
2. Have you operated the player according to the Operating Instructions?
If this unit is not operating properly, check the items listed in the table below. Should the problem persist,
there may be a malfunction. Disconnect the power immediately and contact your store of purchase.
Power supply: AC 120 V, 60 Hz
Power consumption: 2 W
Maximum external dimensions: With dust cover closed :
434 (W) x 122 (H) x 381 (D) mm
(17-3/32” x 4-51/64” x 15”) (including protruding parts)
With dust cover open :
434 (W) x 386 (H) x 413 (D) mm
(17-3/32” x 15-13/64” x 16-19/64”) (including protruding parts)
Mass: 5.5 kg (12 lbs 2 oz)
Drive type: Belt drive
Motor: DC servo motor
Speed: 33-1/3 rpm, 45 rpm
Wow & flutter: 0.10 % W.R.M.S
S/N ratio: 60 dB
Tone arm: Static balance straight type tone arm
Effective arm length: 221.5 mm
Overhang: 19 mm
Cartridge: MM type
Output voltage: With equalizer OFF : 2.5 mV
With equalizer ON : 150 mV
Optimum stylus pressure: 19.6 mN (2.0 g)
Replaceable stylus number: DSN-85
Stylus pressure adjustment range: 0 ~ 39.2 mN (0 ~ 4.0 g)
One step 0.98 mN (0.1 g)
Suitable cartridge empty weight : 44 mN ~ 93 mN (4.5 ~ 9.5 g)
Head shell weight: 98 mN (10.0 g) (including screws and nuts)
Head shell part number: PCL-310BK
* For purposes of improvement, specifications and design are subject to change without notice.
PageMeasuresCause
Power does not turn
on.
Turntable does not turn.
• Power supply cord is not fully
inserted.
• Drive belt is detached from the
turntable.
•
Check the connection.
•
Check the drive belt and driving roller.
If the drive belt is detached from the
turntable, attach it using the
procedure described below.
1.Remove the turntable and turn it
upside down.
2.Catch the belt on the inside perimeter.
3.Turn the turntable back right side up
and pass the tape ribbon through the
hole and between the turn tape and
drive belt.
4.Mount the turntable, referring to the
assembly instructions on page 2.
4
2
The sound is scratchy,
the stylus skips or the
sound is distorted.
•The stylus or record is dirty.
• The stylus is worn or the record is
scratched.
•
Remove the dirt or replace the stylus.
•
Replace the stylus.
•
Check the record.
7
7
—
The sound is either
extremely weak or too
strong and distorted.
• The equalizer switch is not set at the
proper position.
•
Set the switch according to the
terminal to which the player is
connected.
2
Howling is produced.
• The player is too close to the
speakers.
• The player is placed in an unstable
position.
• The playback sound is too loud.
•
Move the player and speakers apart.
•
Check the player’s place of installation.
•
Adjust the amplifier’s volume.
—
—
—
The tone arm does not
move even when the
START button is
pressed.
• The tone arm is clamped to the
armrest.
• The power supply cord is not properly
connected.
•
Remove the tone arm’s clamp.
•
Check the connection of the power
supply cord.
2
4
No sound is produced.
• The pin-plug cable is not properly
connected.
• The amplifier’s function is not set for
the terminals to which the turntable is
connected.
• The replaceable stylus is not properly
mounted.
•
Check the connection.
•
Check the amplifier’s settings.
•
Check the stylus.
4
4
7
ENGLISH
Others
Troubleshooting Specifications
D&M Holdings Inc.
Printed in China 5411 11299 10AD
www.denon.com
DP-300F_E3_Backpage.indd 1 201/0/1 1:47:54
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11

Denon DP-300F Manuel utilisateur

DP-300F
Denon
Marque
Denon
Modèle
DP-300F
Catégorie
Platines audio
Taper
Manuel utilisateur
Télécharger le PDF
rapport

dans d''autres langues

Documents connexes

Autres documents