Honeywell OMNI-408EU Manuel utilisateur

Marque: Honeywell

Modèle: OMNI-408EU

Catégorie: Systèmes de contrôle d'accès de sécurité

Taper: Manuel utilisateur

Ce manuel convient également à

N9942-2V2 4/04 Rev. A

FBII Security System

FBII Security SystemFBII Security System

FBII Security System

User Guide

– 2 –

– 3 –

Table Of Contents

QUICK REFERENCE.............................................................................................4

Arming the System............................................................................................4

Disarming the System ....................................................................................... 4

Arm System/Stay Inside....................................................................................4

Arm System/Stay Inside/Instant Mode..............................................................4

Smoke Detector Reset ......................................................................................4

INTRODUCTION.................................................................................................... 6

SYSTEM REFERENCE .........................................................................................7

SYSTEM OPERATION ........................................................................................10

To Arm the System and Leave .......................................................................10

When the System is Not Ready ...................................................................... 11

To Arm the System and Stay Inside ...............................................................11

To Arm the System In Instant Mode and Stay Inside ..................................... 12

To Arm the System In Instant Mode ...............................................................13

To Bypass a Zone ...........................................................................................13

To Unbypass a Zone.......................................................................................14

Disarming the System ..................................................................................... 14

USER CODES......................................................................................................16

Adding/Changing a User Code .......................................................................16

Deleting a User Code......................................................................................16

PAGING FEATURE..............................................................................................17

Follow-Me Displays .........................................................................................17

Changing the Pager Follow-Me Phone Number .............................................17

MISCELLANEOUS COMMANDS ........................................................................19

TESTING THE SYSTEM......................................................................................22

System Test .................................................................................................... 22

Battery Test.....................................................................................................22

RECOMMENDATIONS ON SMOKE DETECTORS ............................................23

EMERGENCY EVACUATION..............................................................................24

RADIO FREQUENCY EMISSIONS STATEMENTS.................................... 25

FEDERAL COMMUNICATIONS COMMISSION (FCC) PART 15....................... 25

TELEPHONE/MODEM INTERFACE STATEMENTS ................................. 25

TELEPHONE OPERATIONAL PROBLEMS.................................................26

O560 DECLARATION OF CONFORMITY...............................................26

SYSTEM LIMITATIONS.......................................................................................27

GLOSSARY..........................................................................................................29

– 4 –

Quick Reference

Arming the System

Check to make sure the system is ready — Green READY LED is lit.

Enter your 4-digit User Code (or press the ARM button on your

keyfob).

The ARMED LED goes on.

Exit through a door designated by your installer as an exit/entry door.

Disarming the System

Enter through door designated by your installer as an exit/entry door.

Enter your 4-digit User Code (or press the DISARM button on your

keyfob).

The ARMED LED goes out.

Arm System/Stay Inside

Check to make sure the system is ready — Green READY LED is lit.

Press STAY followed by your User Code.

The ARMED and STAY LEDs light.

You must disarm the system if you want to open the door or leave the premises

after the exit time has passed.

Arm System/Stay Inside/Instant Mode

Check to make sure the system is ready — Green READY LED is lit.

Press INSTANT then STAY followed by your User Code.

The ARMED, INSTANT, and STAY LEDs are all lit.

Smoke Detector Reset

Enter your 4-digit User Code.

– 5 –

Quick Reference (cont’d)

The following table lists the “Quick Commands” available with this control.

Keystroke Quick Command Keypads Description

# 1

Quick Arm All keypads

If system is ready, allows you to arm the system without

requiring your User Code. Your User Code is always

needed to disarm the system.

# 2

Force Arm All keypads

Allows you to arm the system even if some zones are

faulted. These zones are automatically bypassed and are

unprotected.

[BYPASS] +

Zone No.

Quick Bypass All keypads

Allows you to bypass a specific zone number. Must be

enabled by your installer.

# 3

Set Time All keypads

Allows entry of the current system time (hours, minutes,

month, day, year).

# 4

Zone Directory LCD only Displays listing of zones in system.

# 55

Display Firmware Version LCD only Displays version of your OMNI-408 firmware.

# 56

Display Keyfob Battery Status All keypads

Allows you to test battery status of your keyfob. Upon

entry of this mode, press any button on the keyfob and the

keypad will display if your battery is low.

# 58

Change/View Pager Number All keypads

Allows you to redirect pager output to a different pager

number. Phone numbers are displayed only on LCD

keypads.

# 6

Display/Toggle Chime Mode All keypads Allows you to change the status of the chime function.

# 7

Display Current Time LCD only Allows you to view the current system time.

# 8

User Page Toggle All keypads

Allows you to turn the pager mode on or off. Keypad

displays the current system status.

– 6 –

Introduction

Congratulations on your decision to protect your home or business

with the OMNI

-408 security system. You have chosen a reliable,

state-of-the-art security system that is remarkably easy to operate.

Representatives from your local security company, who can explain

the specifics of your system, have professionally installed your system.

The keypad is the input and display device for your security system.

Your system can use either the OMNI-KP, OMNI-KP-US, OMNI-LCD,

OMNI-LCD-US, XK7LC, or XK108 keypads. The OMNI-KP and

OMNI-KP-US keypads display the system status with fixed words, the

OMNI-LCD, OMNI-LCD-US, and XK7LC keypads display two lines of

text, and the XK108 keypad displays the current zone status,

including alarms, bypasses, and faults, using LEDs. Each condition

causes the LEDs to operate differently.

Throughout this guide, the following conventions are used to display

the keystrokes required to perform functions.

BYPASS

Key labeled [BYPASS]

INSTANT

Key labeled [INSTANT]

STAY

Key labeled [STAY]

CODE

Key labeled [CODE]

Enter your four-digit User Code.

Please keep your guide in a convenient location so you can refer to it if

needed.

– 7 –

System Reference

ZONE DESCRIPTION

ENTRY

TIME 1

DOOR

EXIT

TIME*

ENTRY

TIME 2

DOOR

* Exit time is the same for all designated entry/exit doors.

The following SEND HELP ALERTS can be programmed into your

system. Both keys must be pressed at the same time to activate the

alert. The keys you press depend on which type of keypad you have.

Your installer will show you how to activate these emergency keys.

DESCRIPTION KEYS

[#] and [*]

[7] and [9]

[1] and [3]

See page 8 of this User Guide for pictures of the OMNI-KP,OMNI-KP-US, OMNI-

LCD, OMNI-LCD-US, XK7LC, and XK108 keypads.

– 8 –

System Reference (cont’d)

OMNI-KP,OMNI-KP-US AND XK108 KEYPADS

ALARM

FIRE

INSTANT

BYPASS

TRBL

PAGE

STAY

SUPRVSN

CANCELED

CHIME

BAT

NOT READY

PHONE

TEST

TAMPER NO AC

OMNI-KP Fixed-Word Keypad

ALARM

FIRE

INSTANT

BYPASS

TRBL

PAGE

STAY

SUPRVSN

CANCELED

CHIME

BAT

NOT READY

PHONE

TEST

TAMPER NO AC

OMNI-KP-US Fixed-Word Keypad

XK108 LED Keypad

OMNI-LCD, OMNI-LCD-US, AND XK7LC KEYPADS

OMNI-LCD Alpha Keypad

OMNI-LCD-US Alpha Keypad

STAY

BYPASS

INSTANT

CODE

XK-7LC_kypd

XK7LC Alpha Keypad

– 9 –

System Reference (cont’d)

USER ID ASSIGNED TO

1 (MASTER USER 1)

6 Duress**

* The Master User can add, change, or erase other User Codes.

** If enabled, this User Code will transmit a duress signal to the central station.

MONITORING STATION INFORMATION

Account No.

Telephone No.

– 10 –

System Operation

You can arm or disarm the burglar portion of your security system.

Before you can arm the system, it must be “ready.” If you have a

protected door open, or if someone is moving in view of a motion

detector, the system will not display “READY.”

The system is ready if the READY LED is lit and the display shows:

LCD Keypad:

SYSTEM READY

Fixed-Word Keypad:

READY LED lit

NOTE: If programmed by your installer, you may arm the system if a

delay or interior zone is faulted. However, faulted zones must be

restored before your exit time expires or an alarm or zone bypass will

result. Ask your installer if your system has this feature and, if so, if it

causes an alarm or zone bypass.

To Arm the System and Leave

Enter your User Code.

The ARMED LED goes on and the display shows:

LCD Keypad:

ON: AWAY

Fixed-Word Keypad:

ARMED LED lit

Exit through a door designated by your installer as an exit/entry door.

You must leave within the exit time programmed by your installer.

Refer to the reference sheet for the time that has been set for your

system.

– 11 –

System Operation (cont’d)

When the System is Not Ready

If the system is not ready to be armed, the READY LED is off and the

display indicates which zone or zones are not ready.

Determine which zone or zones are not ready, resolve the problem,

and arm the system normally. If the problem cannot be resolved, you

may bypass the zone that is not ready. Bypassing should only be done

if the problem on the zone cannot be resolved, OR if you intentionally

wish to leave the zone disarmed. For example, you would leave the

zone disarmed if you plan to keep the window open for ventilation.

Zones that are bypassed are not protected when the system is armed.

Refer to the paragraph entitled, “To Bypass a Zone” for a description

of the procedure.

To Arm the System and Stay Inside

To arm the perimeter portion of your burglar alarm and move around

freely inside the premises, use the STAY mode.

Check to make sure the system is ready. When it is ready, press:

STAY followed by your user code.

When the system has been armed successfully, the ARMED LED is

on, and the following is displayed:

LCD Keypad:

ON: STAY

Fixed-Word Keypad:

STAY

REMEMBER: You must disarm the system if you want to open the

door or leave the premises after the exit time has passed.

– 12 –

System Operation (cont’d)

To Arm the System In Instant Mode and Stay Inside

In INSTANT STAY mode, the perimeter portion of your burglar

alarm system is armed, but the time delays are eliminated from your

normal entry/exit door(s). All interior protection is disarmed, so you

are free to move around inside.

Check to make sure the system is READY. When it is ready, press:

INSTANT followed by

STAY followed by your User Code.

When the system has been armed successfully, the ARMED LED is

on, and the following is displayed:

LCD Keypad:

ON: STAY / INS

Fixed-Word Keypad:

STAY

INSTANT

NOTE: This system can be programmed by the installer for the

AUTOSTAY feature which automatically bypasses interior zones if

you arm the system in AWAY mode, but do not exit through a delay

zone during exit time.

– 13 –

System Operation (cont’d)

To Arm the System In Instant Mode

In INSTANT mode, all alarm sensors, including doors that normally

have a delay to allow you to disarm the system, will immediately

report an alarm if activated. Check to make sure the system is ready.

When it is ready, press:

INSTANT followed by your User Code.

When the system has been armed successfully, the ARMED LED is

on, and the following is displayed:

LCD Keypad:

ON: INSTANT

Fixed-Word Keypad:

INSTANT

To Bypass a Zone

The Bypass function excludes a zone of protection from the security

system until it is unbypassed (either by using the unbypass procedure

or when you disarm the system). Bypassing can only be done while

the system is disarmed.

Press the BYPASS button. Then enter your User Code and the zone

number (1-8) to be bypassed, as follows:

BYPASS followed by your User Code

†

and Zone No. (1-8)

†

If the Quick Bypass feature has been enabled by the installer, do not

enter the User Code when bypassing zones.

– 14 –

System Operation (cont’d)

NOTE: Bypassed zones are NOT protected when the system is armed.

After the bypass command has been accepted, the keypad sounds one

long beep, and the following is displayed:

LCD Keypad:

BYPASSED: ZN1

FRONT DOOR

Fixed-Word Keypad:

BYPASS

zone number displayed

To Unbypass a Zone

Pressing the BYPASS button returns a bypassed zone to normal

operation. To unbypass a zone(s), repeat the bypass function as

follows:

BYPASS followed by your User Code

†

and Zone No. (1-8)

After unbypassing, the zone display shows the state of the zones.

†

If the Quick Bypass feature has been enabled by the installer, do not

enter the User Code when unbypassing zones.

Disarming the System

When you disarm the system, you disarm only the burglar portion of

your system; any smoke or heat detectors and panic keys will remain

armed. You must enter through a designated entry door and disarm

the system within the time allowed. You can have different amounts

of time for different entry points. See your system reference sheet for

the times established for your system.

To disarm your system:

Enter your User Code.

– 15 –

System Operation (cont’d)

If no alarms have taken place, the ARMED LED goes off, and the

display shows:

LCD Keypad:

SYSTEM READY

Fixed-Word Keypad:

READY LED lit

If alarms occurred while the system was armed, or if a trouble

condition exists, the display shows:

LCD Keypad:

ALM MEM ZN1

FRONT DOOR

Fixed-Word Keypad:

ARMED LED off

READY LED blinks

The keypad scrolls through the zone or zones that were in alarm.

Burglary alarms sound a steady tone at the keypad(s), and fire alarms

generate a pulsing sound.

IMPORTANT: If an intrusion has taken place while you were away, do

not enter until the location has been checked. Call for help from a

neighbor's house and wait there for the police.

To clear the display of alarm or trouble conditions and silence the

audible alert:

Enter your User Code again.

– 16 –

User Codes

Adding/Changing a User Code

Users can be added or changed directly at the keypad. Your system

can have up to 6 different User Codes.

To add or change a User Code, press the following:

Master User Code User ID (1-6) New User Code

CODE

NOTES:

• User number 1 is a master user and can create or modify other

users.

•

User number 6 can be a duress code that will transmit a special

duress code to the central station.

Deleting a User Code

To delete a user, press the CODE button followed by the 4-digit

Master User Code. Enter the user number, then press [∗] to delete.

For example, to delete user 3, do the following:

Master User Code User ID (1-6) ∗ to delete

CODE 3 [∗

∗∗

∗] *

NOTE: User number 1, the master user, cannot be deleted, but it can

be changed using the procedure for adding or changing a User Code.

– 17 –

Paging Feature

Your installer may have programmed your system to send messages

with certain system conditions to your pager. An explanation of those

messages is provided below.

Follow-Me Displays

The display shown on your pager is "ACCTEXXX" where:

"ACCT" is the 4-digit central station no. 2 account number.

"E" is the event code. There are 4 event types: alarms, troubles,

openings, and closings. These event codes are as follows:

Openings = 0, Closings = 1, Alarm or Trouble = 9

If multiple events occur, the signal for the highest-priority event is sent first.

Events ranked from highest to lowest priority are alarms, trouble, openings,

and closings.

"XXX" is, depending on the event, the zone (001-008) or user (001-014)

designation.

USER DESIGNATION FUNCTION

1-6 User Codes

7 Remote arm/disarm

8 Quick Arm No. 1, Quick Forced Arm No. 2

9-14 Keyfobs

Changing the Pager Follow-Me Phone Number

You can change your pager follow-me phone number as follows if your

installer enabled this feature:

– 18 –

Paging Feature (cont’d)

1. Access pager number programming by pressing in sequence the

[#], [5], and [8] keys. An acknowledgement tone sounds to indicate

pager number programming has been accessed.

The [#], [5], [8] command is accessible only while the system is disarmed and the

dialer, dialer delay, and bell are not active.

LCD keypads will display the existing pager phone number.

2. Enter your new pager phone number. Your new pager phone

number may consist of up to 16 characters (1-9, 0). It may be

necessary to add time to allow the pager to answer before dialing

your pager number. To enter a 2-second pause, press the [CODE]

key. (Entering a 2-second pause is optional and is not required to

enter your pager phone number.) If the [CODE] key was pressed,

it counts as one character. The keypad will emit a single

acknowledgement chirp as each number is pressed.

3. Press the [#] key after you have made your pager phone number

changes. Pressing the [#] key saves your new pager number and

nulls out the remaining locations. An acknowledgement tone

sounds.

To exit without saving changes, press the [✴] key to exit pager phone

number programming. An acknowledgement tone sounds to indicate

pager number programming has been exited.

If you press the [✴] key without first pressing the [#] key to save your new pager

phone number, the system exits the pager phone number programming mode

without saving the changes.

If no key is pressed within 10 seconds, the pager phone number programming

mode times out and exits automatically without saving any information entered.

– 19 –

Miscellaneous Commands

Arm System (Maid Code)

If you choose to have a code that cannot disarm the system, but can

arm the system, have your installer program this feature. If

programmed, User Code No. 5 has system arming capability only, and

you can issue this code to a temporary user so they can secure the

premises when they leave.

Send Help Conditions

Your system can be programmed for three separate Send Help Alerts

that send an emergency signal to your central station. These three

alerts, along with their keypad combinations, are shown below:

Fire Panic Aux

[7] and [9] [*] and [#] [1] and [3]

Duress

Your system can be programmed to send an emergency signal to the

central station if you are forced to enter the premises. If you choose to

include this feature, User Code No. 6 is dedicated to this function and

must only be used under a duress circumstance.

Quick Arming Yes No

If programmed by your installer, Quick Arming allows you to arm the

system in the Away mode without entering a User Code. To enable

Quick Arm:

Press [#], [1].

– 20 –

Miscellaneous Commands (cont’d)

Quick Forced Arm Yes No

If programmed by your installer, Quick Forced Arm allows you to arm

the burglar portion of your alarm system in the Away mode, bypassing

all zones that are not ready. To enable Quick Force Arm:

Press [#], [2].

A valid User Code is still required to disarm the system.

The Quick Forced Arm feature is disabled on UL installations.

Quick Exit Yes No

If enabled, this feature allows the user to exit without having to

disarm, then arm the system. It is activated by pressing the [STAY]

key while the system is armed and not in entry delay. This starts the

exit time, causes the keypad to beep once, and allows the user to exit

without disarming the system. The system returns to its last armed

state after the exit time has expired.

Quick Bypass Yes No

If you have Quick Bypass programmed for your system, you do not

have to use your User Code to bypass zones. The Quick Bypass

procedure is:

BYPASS , Zone No. (1-8)

Bypassed zones are not protected while the system is armed. After the

Bypass command has been accepted, the keypad sounds one long beep, and

the zone or zones bypassed slowly blink.

La page charge ...

Honeywell OMNI-408EU Manuel utilisateur

Marque: Honeywell

Modèle: OMNI-408EU

Catégorie: Systèmes de contrôle d'accès de sécurité

Taper: Manuel utilisateur

Ce manuel convient également à

Télécharger le PDF

rapport

dans d''autres langues

English: Honeywell OMNI-408EU User manual

Honeywell OMNI-408EU Manuel utilisateur

Ce manuel convient également à

Honeywell OMNI-408EU Manuel utilisateur

dans d''autres langues

Documents connexes

Autres documents