luminii Leto 11 Mini WM Guide d'installation
- Taper
- Guide d'installation
LETO 11 Mini S & WM
1 Rev December 18, 2019 403-216-7043 | [email protected]
MADE IN
CANADA
PROUD MEMBER OF
Read and follow these
instructions before installing or
maintaining this product
Veuillez lire et suivre ces
instructions avant l’installation ou
l’entretien de ce produit
• This product is suitable for DRY INDOOR
LOCATIONS ONLY
• Make sure this product is NOT on the same
circuit as inductive loads, (e.g. fluorescent bulbs,
discharge bulbs, ventilation fans, etc...)
• Do not switch on line voltage until all wiring is
complete
• Incorrect wiring will result in irreparable damage
to LED and power supply
• This product should only be installed by a
licensed electrician
• Ce produit convient pour une installation DANS
UN ENDROIT SEC SEULEMENT
• Assurer vous que des charges inductives ne se
retrouvent pas sur le même circuit que ce produit,
(i.e. fluorescent, ampoules à décharge,
ventilateurs, etc...)
• Compléter les branchements avant de mettre
sous tension
• Un branchement incorrect créerait des
dommages irréparables à l’alimentation et au DEL
• Ce produit devrait être uniquement installé par un
électricien qualifié
Warranty
Garantie
• This product must be installed in accordance
with all applicable installation codes and
ordinance
• Limited five (5) years warranty
• Warranty is void in the eventuality of
unauthorized modifications and/or improper use
• Ce produit doit être installé conformément au
code d’installation et autres normes applicables
• Garantie limitée de cinq (5) ans
• La garantie est non valide advenant une
modification non autorisée ou un usage non
approprié
Wall Mount
AC P4 / DC P5
Ceiling Surface Mount
AC P2 / DC P3
SEMI-RECESSED CANOPY
LETO 11 Mini S & WM
2 Rev December 18, 2019 403-216-7043 | [email protected]
MADE IN
CANADA
PROUD MEMBER OF
1
Finish ceiling installation. Make sure hole is cut to
appropriate size and location. 54mm (2.125”)
Disassemble driver housing to expose the driver.
2
Make electrical connections and use appropriate
strain relief.
3
Reassemble housing and insert into ceiling. Push
aside to leave room for canopy.
4
Line up fixture and insert into canopy
7
Connect dimming controls to included cable
clamps. Insert wires and canopy into ceiling.
5
Twist fixture clockwise until it locks in place.
(magnets will engage)
8
6
Turn screws until housing is secured in place
(arms will extend and clamp down on ceiling)
9-25mm
Surface: Ceiling Mount (AC Connection)
LETO 11 Mini S & WM
3 Rev December 18, 2019 403-216-7043 | [email protected]
MADE IN
CANADA
PROUD MEMBER OF
1
Finish ceiling installation. Make sure hole is cut to
appropriate size and location. 54mm (2.125”)
Disassemble driver housing to expose fixture
wiring. Cylinder housing is used as DC junction
box.
2
Make electrical connections and use appropriate
strain relief.
3
Reassemble housing and insert into ceiling. Push
aside to leave room for canopy.
4
Line up fixture and insert into canopy
7
Insert canopy into ceiling.
5
Twist fixture clockwise until it locks in place.
(magnets will engage)
8
6
Turn screws until housing is secured in place
(arms will extend and clamp down on ceiling)
9-25mm
Surface: Ceiling Mount (Remote DC Connection)
LETO 11 Mini S & WM
4 Rev December 18, 2019 403-216-7043 | [email protected]
MADE IN
CANADA
PROUD MEMBER OF
1
Finish wall installation. Make sure hole is cut to
appropriate size and location. 54mm (2.125”)
Disassemble driver housing to expose the driver.
2
Make electrical connections and use appropriate
strain relief.
3
Reassemble housing and insert into wall.
4
Line up fixture and insert into canopy
7
Connect dimming controls to included cable
clamps. Insert wires and canopy into ceiling.
5
Twist fixture clockwise until it locks in place.
(magnets will engage)
8
Surface: Wall Mount (AC Connection)
6
Turn screws until housing is secured in place
(arms will rotate and clamp against wall)
9-25mm
LETO 11 Mini S & WM
5 Rev December 18, 2019 403-216-7043 | [email protected]
MADE IN
CANADA
PROUD MEMBER OF
1
Finish wall installation. Make sure hole is cut to
appropriate size and location. 54mm (2.125”)
Disassemble driver housing to expose fixture
wiring. Cylinder housing is used as DC junction
box.
2
Make electrical connections and use appropriate
strain relief.
3
Reassemble housing and insert into wall.
4
Line up fixture and insert into canopy
7
Insert canopy into wall. Use flat sides to level
canopy horizontally.
5
Twist fixture clockwise until it locks in place.
(magnets will engage)
8
6
Turn screws until housing is secured in place
(arms will rotate and clamp against wall)
9-25mm
Surface: Wall Mount (Remote DC Connection)
-
1
-
2
-
3
-
4
-
5
luminii Leto 11 Mini WM Guide d'installation
- Taper
- Guide d'installation
dans d''autres langues
Documents connexes
-
luminii Leto 44 Mini WM UD Guide d'installation
-
-
-
-
-
-
-
-
-