Summit CL67ROSB Le manuel du propriétaire

Taper
Le manuel du propriétaire

Ce manuel convient également à

FROST-FREE REFRIGERATORS
for INDOOR and OUTDOOR USE
RÉFRIGÉRATEURS SANS GIVRE
pour usage intérieur et extérieur
Instruction Manual / Mode d’emploi
Models / Modèles CL67ROSB / CL69ROSW
BEFORE USE, PLEASE READ AND FOLLOW ALL SAFETY RULES AND OPERATING INSTRUCTIONS.
AVANT L'UTILISATION, VEUILLEZ LIRE ET SUIVRE TOUTES LES REGLES DE SECURITE ET LES
INSTRUCTIONS D'UTILISATION.
Felix Storch, Inc.
An ISO 9001:2015 registered company
770 Garrison Avenue
Bronx, NY 10474
www.summitappliance.com
Write Serial Number (on lower left corner of
inside cabinet) here:
Écrivez le numéro de série (dans le coin
inférieur gauche de l'armoire intérieure) ici:
______________________________
2
TABLE OF CONTENTS
Appliance Safety
3
Important Safeguards
3 - 4
Location of Parts
5
Installation Instructions
6 - 8
Before Using Your Appliance
6
Installation of Your Appliance
6
Electrical Connection
6 - 7
Extension Cord
7
Reversing the Door Swing of Your Appliance
7 - 8
Installing the Stainless Steel Handle
8
Operating Your Appliance
8 - 10
Control Panel
8 - 9
Sabbath Mode
9
Temperature Memory Function
9
Defrosting
10
Temperature Alarm / Door Alarm
10
Door Lock
10
Shelves
10
Care and Maintenance
11
Cleaning Your Appliance
11
Power Failure
11
Vacations
11
Moving Your Appliance
11
Energy-Saving Tips
11
Troubleshooting
12 - 13
Limited Warranty
14
French version of this manual
15 - 28
3
APPLIANCE SAFETY
Your safety and the safety of others are very important.
We have provided many important safety messages in this manual and on your appliance. Always read
and obey all safety messages.
This is the Safety Alert Symbol. The symbol alerts you to potential hazards that
can kill or injure you and others. All safety messages will follow the Safety
Alert Symbol and either the word DANGER or WARNING.
DANGER means that failure to heed this safety
statement may result in severe personal injury or
death.
WARNING means that failure to heed this safety
statement may result in extensive product
damage, serious personal injury, or death.
All safety messages will alert you about the potential hazard, tell you how to reduce the chance of injury,
and let you know what can happen if the instructions are not followed.
IMPORTANT SAFEGUARDS
Before the appliance is used, it must be properly positioned and installed as
described in this manual, so read the manual carefully. To reduce the risk of fire,
electrical shock or injury when using the appliance, follow basic precautions,
including the following:
Plug into a grounded 3-prong outlet, do not remove grounding prong, do not use an adapter, and do
not use an extension cord.
Replace all panels before operating.
It is recommended that a separate circuit serving only your appliance be provided. Use receptacles
that cannot be turned off by a switch or pull chain.
Never clean appliance parts with flammable fluids. These fumes can create a fire hazard or explosion.
And do not store or use gasoline or other flammable vapors and liquids in the vicinity of this or any
other appliance. The fumes can create a fire hazard or explosion.
Do not connect or disconnect the electric plug when your hands are wet.
Unplug the appliance or disconnect power before cleaning or servicing. Failure to do so can result in
electrical shock or death.
Do not attempt to repair or replace any part of your appliance unless it is specifically recommended in
this manual. All other servicing should be referred to a qualified technician.
This appliance is CFC- and HFC-free and contains small quantities of Isobutane (R600a), which is
environmentally friendly but flammable. It does not damage the ozone layer nor does it increase the
greenhouse effect. Care must be taken during transportation and setting up of the appliance that no
parts of the cooling system are damaged. Leaking coolant can ignite and may damage the eyes.
In the event of any damage:
4
- Avoid open flames and anything that creates a spark,
- Disconnect from the power supply,
- Air the room in which the appliance is located for several minutes and
- Contact the Service Department for advice.
The more coolant there is in an appliance, the larger the room it should be installed in. In the event of
a leakage, if the appliance is in a small room, there is the danger of combustible gases building up.
For every ounce of coolant, at least 325 cubic feet of room space is required. The amount of coolant in
the appliance is stated on the data plate inside the appliance. It is hazardous for anyone other than an
Authorized Service Person to carry out servicing or repairs to this appliance.
Take serious care when handling, moving and using the appliance to avoid either damaging the
refrigerant tubing or increasing the risk of a leak.
Replacing component parts and servicing shall be done by factory authorized service personnel so as
to minimize the risk of possible ignition due to incorrect parts or improper service.
FOLLOW WARNING CALLOUTS BELOW ONLY WHEN APPLICABLE TO YOUR MODEL
Use two or more people to move and install appliance. Failure to do so can result in back or other
injury.
To ensure proper ventilation for your appliance, the front of the unit must be completely unobstructed.
Choose a well-ventilated area with temperatures above 44°F (7°C) and below 100°F (38°C). [The unit
performs best when the ambient temperature is between 72º and 78ºF (23º to 26ºC).]
The appliance should not be located next to ovens, grills or other sources of high heat.
The appliance must be installed with all electrical, water and drain connections in accordance with
state and local codes. A standard electrical supply (115 V AC only, 60 Hz), properly grounded in
accordance with the National Electrical Code and local codes and ordinances, is required.
Do not kink or pinch the power supply cord of the appliance.
The size of the fuse (or circuit breaker) should be 15 amperes.
It is important that the appliance be leveled in order to work properly. You may need to make several
adjustments to level it.
All installations must be in accordance with local plumbing code requirements.
Make certain that the pipes are not pinched, kinked or damaged during installation.
Check for leaks after connection.
Never allow children to operate, play with or crawl inside the appliance.
Do not use solvent-based cleaning agents or abrasives on the interior. These cleaners may damage
or discolor the interior.
Use this appliance only for its intended purpose as described in this Instruction Manual.
Keep fingers out of the “pinch point” areas. Clearances between the door and cabinet are necessarily
small. Be careful closing the door when children are in the area.
Risk of child entrapment!
Child entrapment and suffocation are not problems of the past. Junked or abandoned appliances are
still dangerous, even if they will “just sit for a few days”.
Before discarding your old refrigerator:
Take off the doors
Leave the shelves in place so that children may not easily climb inside.
- SAVE THESE INSTRUCTIONS -
5
LOCATION OF PARTS
Digital Control Panel
Shelves (3)
Kick-plate
Adjustable Legs
LED Light
Security Lock
Stainless Steel Door
Door Racks (2)
6
INSTALLATION INSTRUCTIONS
BEFORE USING YOUR APPLIANCE
Remove the exterior and interior packing.
Before connecting the appliance to the power source, let it stand upright for approximately 2 hours.
This will reduce the possibility of a malfunction in the cooling system from handling during
transportation.
Clean the interior surface with lukewarm water using a soft cloth.
Install the handle on the door if it is not already attached. (See page 8.)
INSTALLATION OF YOUR APPLIANCE
The appliance is designed for built-in or recessed or free-standing installation for indoor or outdoor
use.
CAUTION: This appliance is not designed for the storage of medicine or other medical products.
Place your appliance on a floor that is strong enough to support it when it is fully loaded. To level the
unit, adjust the front leveling legs.
For free-standing installation, 5 (127mm) of space between the back and sides of the unit, and 4”
(102mm) at the top, are suggested, which allows the proper air circulation to cool the compressor and
condenser. Even for built-in installation, it is a must to keep ¼” (6.35mm) of space on each side and at
the top and 2” (51mm) at the rear. Take care that the air vent at the front of the appliance is never
covered or blocked in any way.
NOTE: It is recommended that you do not install the appliance near an oven, radiator or other heating
source. Direct sunlight may affect the acrylic coating and heat sources may increase electrical
consumption. Don’t install in a location where the temperature will fall below 44°F (7°C). For best
performance, do not install the appliance behind a cabinet door or block the base grille.
Avoid locating the unit in moist areas.
Plug the appliance into an exclusive, properly grounded wall outlet.
ELECTRICAL CONNECTION
This appliance should be properly grounded for your safety. The power cord of this appliance is equipped
with a three-prong plug which mates with standard three-prong wall outlets to minimize the possibility of
electrical shock.
Do not under any circumstances cut or remove the third (ground) prong from the power cord supplied. For
personal safety, this appliance must be properly grounded. Any questions concerning power and/or
grounding should be directed toward a certified electrician or an authorized service center.
This appliance requires a standard 115/120 Volt AC ~ 60Hz three-prong grounded electrical outlet. Have
the wall outlet and circuit checked by a qualified electrician to make sure the outlet is properly grounded.
When a standard 2-prong wall outlet is encountered, it is your responsibility and obligation to have it
replaced with a properly grounded 3-prong wall outlet.
To prevent accidental injury, the cord should be secured behind the appliance and not left exposed or
dangling.
WARNING
Improper use of the grounded plug can result in the risk of electrical shock. If the power cord is
damaged, have it replaced by a qualified electrician or an authorized service center.
7
The appliance should always be plugged into its own individual electrical outlet having a voltage rating
that matches the rating label on the appliance. This provides the best performance and also prevents
overloading house wiring circuits that could cause a fire hazard from overheating. Never unplug the
appliance by pulling on the power cord. Always grip the plug firmly and pull straight out from the
receptacle. Repair or replace immediately all power cords that have become frayed or otherwise
damaged. Do not use a cord that shows cracks or abrasion damage along its length or at either end.
When moving the appliance, be careful not to damage the power cord.
EXTENSION CORD
Because of potential safety hazards under certain conditions, it is strongly recommended that you do not
use an extension cord with this appliance. However, if you must use an extension cord, it is absolutely
necessary that it be a UL/CUL-Listed, 3-wire grounding type appliance extension cord having a grounding
type plug and outlet and that the electrical rating of the cord be 115 volts and at least 10 amperes.
REVERSING THE DOOR SWING OF YOUR APPLIANCE
This unit has the capability of the door opening from either the left or right side. The unit is delivered to
you with the door opening from the left side. Should you desire to reverse the opening direction, please
follow the reversal instructions shown below.
NOTE: All parts removed must be saved to allow the door swing to be reversed.
1. Remove the bottom hinge (2) by unscrewing the four lock screws (1).Be careful to hold the door firmly
after removing the screws. (Fig. 1)
2. Gently pull down to remove the door from the right top hinge and place it on a padded surface to
avoid the risk of damage. Then remove the right top hinge (4). (Figs. 3 & 4)
3. Unscrew and transfer pins (3) and (7) of the hinge plate to the opposite side. (Fig. 2)
8
4. Pop out the cover caps on the left side of the cabinet and use them to cover the screw holes on the
right-hand side.
5. Screw the alternative left top hinge (6), included in the fittings, on the left hand side of the cabinet.
(Fig. 3)
6. Relocate the door to the designated position. Then screw the bottom hinge assembly on the left
designated position and tighten it after the door is leveled.
7. Remove the handle from the left side of the door and install it on the right side. (See next section.)
INSTALLING THE STAINLESS STEEL HANDLE
This appliance includes a stainless steel handle that is not required
to operate the unit. To install the handle, follow the instructions
below:
1. Remove the door gasket (2) on the side you wish to install the
handle - you can see two designated holes for handle
installation.
2. Install the handle (4) tightly as shown above with two screws (1)
and flat washers (3) provided.
3. Replace the door gasket.
OPERATING YOUR APPLIANCE
It is recommended that you install the appliance in a place where the ambient temperature is between 72º
and 78ºF (23º to26ºC). If the ambient temperature is above or below the recommended temperatures,
the performance of the unit may be affected. For example, placing your unit in extremely cold or hot
conditions may cause interior temperatures to fluctuate. The operating temperature range may not be
reached.
CONTROL PANEL
ON/OFF Power
To turn the appliance off, press and hold the key for 5 seconds until the temperature display
goes off. To turn the appliance on, press and hold the key for 1 second until the temperature
display lights up.
NOTE: Pressing the POWER key once can switch off the audible alarm when the alarm is on.
LIGHT
To control the inner light.
UP
Used to increase (warm) the set temperature by 1°C/1ºF.
9
DOWN
Used to decrease (cool) the set temperature by 1°C/1ºF.
ºF/ºC Selector
Select the temperature display in Fahrenheit or Celsius degrees. To change the temperature from
Fahrenheit to Celsius or from Celsius to Fahrenheit, press and hold the LIGHT key for 5 seconds.
Setting the Temperature Control
You can set the temperature by touching the UP and DOWN symbols. When you push either of
the two buttons for the first time, the LED readout will show the original temperature set
previously. (The temperature preset at the factory is 38°F, or 3°C.)
The temperature you are setting will increase by one degree each time you touch the UP
symbol, and will decrease by one degree each time you touch the DOWN symbol.
The range of the temperature control is from 36°F to 43°F.
To view the set temperature at any time, touch the UP or DOWN symbol. The set temperature
will flash in the display window for 5 seconds. After 5 seconds, the temperature inside the unit
will reappear in the display window.
Interior Light
The interior light makes it easy to view your items. Touching the LIGHT symbol toggles between
2 modes of operation for the internal lights: functional (default) mode and showcase mode. If
you are in functional (default) mode, the lights will turn on only when the door is open. If you are
in showcase mode, the lights will be on whether or not the door is open.
SABBATH MODE
Sabbath mode is available for the observance of certain religious holidays. This mode turns off the
displays, interior light and audible alarms and prevents them from turning on again. Normal cooling
operations will still take place.
To initiate Sabbath mode, press the POWER and LIGHT keys at the same time for at least 5 seconds.
The indicator light will flash four times and confirm that the Sabbath mode is ON.
Sabbath mode can be exited by repeating the above process. The Sabbath Mode will automatically turn
off after 96 hours.
TEMPERATURE MEMORY FUNCTION
In the event of a power interruption (power surge, breaker switch, etc.), the unit can remember the
previous temperature settings, and when the power is recovered, the cabinet temperature will return
to the same setting temperature as before the power went off.
NOTE:
If the unit is unplugged, or power is lost or turned off, you must wait 3 to 5 minutes before
restarting the unit. If you attempt to restart before this time delay, the unit will not start.
When you use the unit for the first time or restart the unit after it has been shut off for a long time,
there could be a few degrees variance between the temperature you select and the one indicated
on the LED readout. This is normal and is due to the length of the activation time. There should
not be a problem once the unit has been running for a few hours.
10
DEFROSTING
The unit defrosts automatically in normal operating conditions.
The evaporator behind the rear wall of the unit defrosts automatically. The condensate collects in the
drainage channel behind the rear wall of the unit, and flows through the drainage hole into the drip
tray by the compressor where it evaporates.
However, frost may accumulate on the evaporator if the unit is repeatedly opened in a high heat or
high humidity location. If this frost pattern does not clear within 24 hours, your unit will require manual
defrosting.
TEMPERATURE ALARM / DOOR ALARM
An audible alarm sounds if the storage temperature is not cold enough. The temperature display
flashes at the same time.
The cause of the temperature being too high may be:
Warm fresh food was placed inside
Too much warm ambient air flowed in when rearranging or removing food
Power failure for some time
The appliance is faulty
The audible alarm is automatically silenced and the temperature display stops flashing when the
temperature is sufficiently cold again.
If the door has been left open for more than 60 seconds, the alarm will sound. Pressing the POWER
key once can switch off the audible alarm.
DOOR LOCK
Your unit is provided with a lock and key combination.
The keys are located inside the plastic bag that contains the Instruction Manual. Insert the key into the
lock and turn it counter-clockwise to unlock the door. To lock the door, do the reverse operation, making
sure the metal pin is engaged completely. Remove the key and put it in a secure place for safekeeping.
SHELVES
To prevent damaging the door gasket, make sure to have the door all the way open when pulling the
shelves out of the rail compartment.
Any of the shelves can be removed to store larger items.
When removing the shelf out of the rail compartment, make
sure to remove all items first. Then move the shelf to the
position where the notch of the shelf is exactly under the
plastic post and lift the shelf. In order to replace the shelf,
repeat steps described above in reverse.
11
CARE AND MAINTENANCE
CLEANING YOUR APPLIANCE
Turn off the power, unplug the appliance, and remove all items, including shelves.
Wash the inside surfaces with a solution of warm water and baking soda (about 2 tablespoons of
baking soda to a quart of water).
Wash the shelves with a mild detergent solution.
Wring excess water out of the sponge or cloth when cleaning the area where the controls are located,
or any electrical parts.
Wash the outside cabinet with warm water and mild liquid detergent. Rinse well and wipe dry with a
clean soft cloth.
Use an approved stainless steel cleaner to clean the handle. Do not use steel wool or a steel brush
on the stainless steel.
CAUTION:
Failure to unplug the appliance during cleaning could result in electrical shock or other personal injury
.
POWER FAILURE
Most power failures are corrected within a few hours and should not affect the temperature of your
appliance if you minimize the number of times the door is opened. If the power is going to be off for a
longer period of time, you need to take the proper steps to protect the contents.
VACATIONS
Short vacations: Leave the appliance operating during vacations of less than three weeks.
Long vacations: If the appliance will not be used for several months, remove all items and turn off
the appliance. Clean and dry the interior thoroughly. To prevent odor and mold growth, leave the
door open slightly, blocking it open if necessary.
MOVING YOUR APPLIANCE
1. Remove all items.
2. Securely tape down all loose items (shelves) inside your appliance.
3. Turn the adjustable legs up to the base to avoid damage.
4. Tape the door shut.
5. Be sure the appliance stays secure in the upright position during transportation. Also, protect the
outside of the appliance with a blanket or similar item.
ENERGY-SAVING TIPS
The appliance should be located in the coolest area of the room, away from heat-producing
appliances and out of direct sunlight.
Ensure that the unit is adequately ventilated. Never cover air vents.
Do not keep the door open any longer than necessary.
Let hot foods cool to room temperature before placing in the unit. Overloading the unit forces the
compressor to run longer.
Be sure to wrap foods properly, and wipe containers dry before placing them in the unit. This cuts
down on frost build-up inside the unit.
Unit shelves and storage bins should not be lined with aluminum foil, wax paper, or paper toweling.
Liners interfere with cold air circulation, making the unit less efficient.
Organize and label food to reduce door openings and extended searches. Remove as many items as
needed at one time, and close the door as soon as possible.
12
TROUBLESHOOTING
You can solve many common problems easily, saving you the cost of a possible service call. Try the
suggestions below to see if you can solve the problem before calling the servicer.
Troubleshooting Guide
PROBLEM
POSSIBLE CAUSE
REMEDY
Appliance
does not
operate.
Appliance is not connected to a power
supply.
The appliance is turned off.
Tripped circuit breaker or a blown fuse.
Connect the appliance.
Switch on the appliance.
Switch on circuit breaker or replace
fuse.
Appliance is
not cold
enough.
The temperature is not set correctly.
The ambient temperature could require
a lower temperature setting.
The door was opened too often.
The door was not closed completely.
Door is not hermetically sealed.
The condenser is too dirty.
The ventilation opening is blocked or too
dusty.
Check the set temperature.
Set a lower temperature.
Do not open the door more often than
necessary.
Close door properly.
Check the door seal and clean or
replace.
Clean the condenser when necessary.
Clear the obstructions and clean off
the dust.
Appliance
turns itself on
and off
frequently.
The room temperature is higher than
average.
A large amount of items have been
added to the unit.
The door is open too often.
The door is not closed completely.
The door gasket does not seal properly.
Put the appliance in a cooler place.
Leave the appliance to work for a
while until the set temperature has
been reached.
Do not open the door more often than
necessary.
Close door properly.
Check the door seal and clean or
replace.
The light does
not work.
Appliance is not connected to a power
supply.
Tripped circuit breaker or a blown fuse.
The light was switched off on the control
panel.
Connect the appliance.
Switch on circuit breaker or replace
fuse.
Switch on the light.
Vibrations
The appliance is not properly leveled.
Level the appliance with the
adjustable feet.
The appliance
seems to
make too
much noise.
The rattling noise may come from the flow of the refrigerant, which is normal. As each
cycle ends, you may hear gurgling sounds caused by the flow of refrigerant in your
appliance.
If temperature fluctuations occur, the contraction and expansion of the inner walls may
cause popping and crackling noises.
The appliance is not properly level.
Level the appliance with the
adjustable feet.
The door will
not close
properly.
The appliance is not properly level.
The door was reversed and not properly
installed.
The gasket is dirty.
The shelves are out of position.
Level the appliance with the
adjustable feet.
Check the door hinge and reassemble
correctly.
Clean the door gasket.
Check the shelves and refit correctly.
13
Display “E0,
“E1”. “E2,
“E3, “E4,
“E5 or “E7”.
E0 indicates a communication error for
3-zone models.
E1 or E2 indicates that the air
temperature sensor has failed.
E3 or E4indicates that the defrost
sensor in the evaporator has failed.
E5 indicates a defrost heater failure.
E7 indicates a door switch failure.
Call for service.
The alarm
sounds and
the
temperature
display
flashes.
Has the appliance door been open for
longer than 60 seconds? If not, then the
temperature has risen higher or fallen
lower than the temperature that has been
set. This could be due to:
The appliance door being opened too
often.
The ventilation opening being covered
or too dusty.
A lengthy interruption in the power
supply.
A large amount of items have been
added to the unit.
If yes, close the door.
Do not open the door more often than
necessary.
Clear the obstructions and clean off
the dust.
Leave the appliance to work for a
while until the set temperature has
been reached.
The icon “--” is
lit and flashing
in the
temperature
display.
The display temperature is out of range.
Only temperatures within the range
0~99°F/-9~37°C can be displayed. If
the temperature is not within this
range, the icon “-- will be displayed
instead. This is normal.
If you've checked the table above and find that you still need help with your appliance, call our Customer
Service facility at 800-932-4267 between 9:00AM and 5:00PM ET. We will do our best to answer your
questions.
CALIFORNIA CARB/SNAP DISCLOSURE For products manufactured after
January, 1, 2019:
Retail food refrigeration equipment manufactured after January 1, 2019,
designed to store and display chilled goods for commercial sale, and that use
HFC-134a/R134a refrigerant are not for sale in California.
*This product uses eco-friendly hydrocarbon refrigerant and fully complies with
California CARB regulations. However, we are required by California Law to
provide the previous disclosure statement in every product sold in California.
This product does not use any refrigerants on the “List of Prohibited
Substances.”
14
LIMITED WARRANTY
ONE-YEAR LIMITED WARRANTY
Within the 48 contiguous United States, for one year from the date of purchase, when this appliance is
operated and maintained according to instructions attached to or furnished with the product, warrantor will
pay for factory-specified parts and repair labor to correct defects in materials or workmanship. Service
must be provided by a designated service company. Outside the 48 states, all parts are warranted for
one year from manufacturing defects. Plastic parts, shelves and cabinets are warranted to be
manufactured to commercially acceptable standards, and are not covered from damage during handling
or breakage.
ITEMS WARRANTOR WILL NOT PAY FOR:
1. Service calls to correct the installation of your appliance, to instruct you how to use your appliance, to
replace or repair fuses or to correct wiring or plumbing.
2. Service calls to repair or replace appliance light bulbs or broken shelves. Consumable parts (such as
filters) are excluded from warranty coverage.
3. Damage resulting from accident, alteration, misuse, abuse, fire, flood, acts of God, improper
installation, installation not in accordance with electrical or plumbing codes, or use of products not
approved by warrantor.
4. Replacement parts or repair labor costs for units operated outside the United States.
5. Repairs to parts or systems resulting from unauthorized modifications made to the appliance.
6. The removal and reinstallation of your appliance if it is installed in an inaccessible location or is not
installed in accordance with published installation instructions.
DISCLAIMER OF IMPLIED WARRANTIES; LIMITATION OF REMEDIES
CUSTOMER'S SOLE AND EXCLUSIVE REMEDY UNDER THIS LIMITED WARRANTY SHALL BE
PRODUCT REPAIR AS PROVIDED HEREIN. IMPLIED WARRANTIES, INCLUDING WARRANTIES OF
MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE, ARE LIMITED TO ONE YEAR.
WARRANTOR SHALL NOT BE LIABLE FOR INCIDENTAL OR CONSEQUENTIAL DAMAGES. SOME
STATES DO NOT ALLOW THE EXCLUSION OR LIMITATION OF INCIDENTAL OR CONSEQUENTIAL
DAMAGES, OR LIMITATIONS ON THE DURATION OF IMPLIED WARRANTIES OF
MERCHANTABILITY OR FITNESS, SO THESE EXCLUSIONS OR LIMITATIONS MAY NOT APPLY TO
YOU. THIS WARRANTY GIVES YOU SPECIFIC LEGAL RIGHTS AND YOU MAY ALSO HAVE OTHER
RIGHTS, WHICH VARY FROM STATE TO STATE.
WARNING: This product can expose you to chemicals including Nickel
(Metallic) which is known to the State of California to cause cancer.
For more information go to www.P65Warnings.ca.gov
Note: Nickel is a component in all stainless steel and some other metallic compositions.
FELIX STORCH, INC.
770 Garrison Avenue
Bronx, NY10474
Phone: (718) 893-3900
Fax: (844) 478-8799
www.summitappliance.com
For parts and accessory ordering,
troubleshooting and helpful hints, visit:
www.summitappliance.com/support
15
TABLE DES MATIÈRES
Consignes de sécurité
16
Mesures de sécurité importantes
16 - 17
Emplacement des pièces
18
Instructions d'installation
19 - 21
Avant d'utiliser votre appareil
19
Installation de votre appareil
19 - 20
Connexion électrique
20
Rallonge
20
Inversion de l'ouverture de la porte de votre appareil
20 - 21
Installation de la poignée en acier inoxydable
22
Utilisation de votre appareil
21 - 23
Panneau de contrôle
21 - 22
Mode Sabbat
22
Fonction de mémoire de température
23
Dégivrage
23
Alarme de température / Alarme de porte
23
Verrou
23
Étagères
23
Soin et entretien
24
Nettoyage de votre appareil
24
Panne électrique
24
Vacances
24
Déplacer votre appareil
24
Conseils d'économie d'énergie
24
Dépannage
25 - 26
Garantie limitée
28
16
CONSIGNES DE SÉCURITÉ
Votre sécurité et celle des autres est très importante.
Nous avons fourni de nombreux messages de sécurité importants sur votre appareil
dans ce manuel. Toujours lire et respecter les consignes de sécurité. Tous les
messages de sécurité suivront le symbole d'alerte de sécurité, soit après le mot
"DANGER" ou "AVERTISSEMENT".
DANGER est le symbole d'alerte de sécurité. Ce
symbole vous signale les dangers potentiels qui
pourraient tuer or blesser vous et les autres.
Le symbole AVERTISSEMENT signifie que le
non-respect de ce message de sécurité peut
entraîner des dommages importants au produit,
des blessures graves ou la mort.
Tous les messages de sécurité vous alertent au danger potentiel et vous expliquent comment réduire le
risque de blessure et les conséquences qui peuvent se produire si les instructions ne sont pas suivies.
MESURES DE SÉCURITÉ IMPORTANTES
Avant que l’appareil soit utilisé, il doit être correctement positionné et installé
comme décrit dans ce manuel, lisez attentivement le manuel. Pour réduire le
risque d'incendie, choc électrique ou des blessures lors de l'utilisation de l'appareil,
suivez les précautions de base, y compris les suivantes:
Branchez sur une prise à 3 broches de sortie, ne retirez pas la broche de terre, ne pas utiliser un
adaptateur, et ne pas utiliser une rallonge.
Replacez tous les panneaux avant de faire fonctionnement l'appareil.
Il est recommandé d'utiliser un circuit distinct afin d'alimenter votre appareil uniquement. Utilisez des
récipients qui ne peuvent pas être désactivés par un interrupteur ou une chaîne de traction.
Ne jamais nettoyer des pièces d'appareils avec des liquides inflammables. Les émanations peuvent
provoquer un incendie ou une explosion. Ne pas stocker ni utiliser d'essence ou autres vapeurs et
liquides inflammables à proximité de cet appareil ou de tout autre. Les vapeurs peuvent créer un risque
d'incendie ou d'explosion.
Avant de procéder à des opérations de nettoyage et d'entretien, assurez-vous que la ligne
d'alimentation de l'appareil soit débranchée.
Ne pas brancher ou débrancher la prise électrique lorsque vos mains sont mouillées.
Débranchez l'appareil ou couper le courant avant de le nettoyer ou de le réparer. Le non-respect de
cette consigne peut entraîner un choc électrique ou la mort.
Ne tentez pas de réparer ou de remplacer une partie quelconque de votre appareil à moins qu'il ne soit
spécifiquement recommandé de le faire dans ce manuel. Toute autre réparation doit être confiée à un
technicien qualifié.
Cet appareil est exempt de CFC et de HFC et contient de petites quantités d'isobutane (R600a), qui est
respectueux de l'environnement, mais inflammable. Il ne porte pas atteinte à la couche d'ozone ni
n'augmente l'effet de serre. Pendant le transport et l'installation de l'appareil, il faut veiller à ce
AVERTISSEMENT
17
qu'aucune partie du système de refroidissement ne soit endommagée. Une fuite de liquide de
refroidissement peut s'enflammer et peut endommager les yeux.
En cas de dommage :
- Éviter les flammes nues et tout ce qui produit une étincelle,
- Débrancher de l'alimentation électrique,
- Aérer la pièce dans laquelle se trouve l'appareil pendant plusieurs minutes, et
- Communiquer avec le Service technique pour obtenir des conseils.
Plus un appareil contient de liquide de refroidissement, plus la pièce dans laquelle il sera installé doit être
grande. Dans le cas d'une fuite, si l'appareil est dans une petite pièce, il y a danger d'accumulation de gaz
combustibles. Pour chaque once de liquide de refroidissement, un minimum de 9,20 m
3
d'espace est
nécessaire. La quanti de liquide de refroidissement que contient l'appareil est indiqe sur la plaque
signatique à l'arrière de l'appareil. Il est dangereux pour quiconque autre qu'un technicien de service
autori de proder à l'entretien ou la réparation de cet appareil.
Faire attention lors de la manipulation, du déplacement, et l'utilisation de l'appareil, afin d'éviter soit
d'endommager la tuyauterie de réfrigérant ou d'augmenter le risque de fuite.
Le remplacement des pièces et l'entretien doivent être effectués par le personnel de service autorisé
de manière à minimiser le risque possible d'inflammation en raison de mauvaises pièces ou d'un
entretien inadéquat.
SUIVEZ CES AVERTISSEMENTS SEULEMENT LORSQU'ILS SONT APPLICABLES À VOTRE MODÈLE
Utilisez deux personnes ou plus pour déplacer et installer l'appareil. Ne pas le faire peut entraîner des
blessures au dos.
Pour assurer une ventilation adéquate de votre appareil, l'avant de l'appareil doit être complètement
dégagé. Choisissez un endroit bien ventilé avec des températures supérieures à 7 ° C (44 ° F) et
inférieures à 32 ° C (90 ° F).
L'appareil ne doit pas être situé à proximité de fours, de grils ou d'autres sources de chaleur.
L'appareil doit être installé avec tous les raccordements électriques, d'eau et de vidange
conformément aux codes locaux et d'état. Une alimentation électrique standard (115 VCA
uniquement, 60 Hz), correctement mise à la terre conformément au Code national de l'électricité et
aux codes et règlements locaux, est requise.
Ne pas plier ou pincer le cordon d'alimentation de l'appareil.
La taille du fusible (ou du disjoncteur) doit être de 15 ampères.
Il est important que l'appareil soit mis à niveau pour fonctionner correctement. Vous devrez peut-être
effectuer plusieurs ajustements pour le niveler.
Toutes les installations doivent être conformes aux exigences du code de plomberie local.
Assurez-vous que les tuyaux ne sont pas pincés, pliés ou endommagés lors de l'installation.
Vérifiez les fuites après la connexion.
Ne laissez jamais les enfants fonctionner, jouer avec ou ramper à l'intérieur de l'appareil.
N'utilisez pas de produits nettoyants à base de solvants ou d'abrasifs à l'intérieur. Ces nettoyants
peuvent endommager ou décolorer l'intérieur.
Utilisez cet appareil uniquement pour l'usage prévu, tel que décrit dans ce manuel d'instructions.
Gardez les doigts hors des zones de "pincement". Les dégagements entre la porte et le meuble sont
nécessairement petits. Faites attention en fermant la porte quand les enfants sont dans la zone.
Risque de piégeage des enfants!
La capture d'enfants et la suffocation ne sont pas des problèmes du passé. Les appareils indésirables
ou abandonnés sont toujours dangereux, même s’ils «resteront assis pendant quelques jours».
Avant de jeter votre vieux réfrigérateur :
• Enlever les portes
• Laissez les étagères en place pour que les enfants ne puissent pas facilement y pénétrer.
AVERTISSEMENT
- CONSERVER CES INSTRUCTIONS -
18
EMPLACEMENT DES PIÈCES
Digital Control Panel
Shelves (3)
Kick-plate
Adjustable Legs
LED Light
Security Lock
Stainless Steel Door
Door Racks (2)
Verrou de sécurité
Porte en acier
inoxydable
Lumière LED
Panneau de
commande numérique
Plaque de protection
Racks de porte (2)
Étagères (3)
Pieds réglables
19
INSTRUCTIONS D’INSTALLATION
AVANT D'UTILISER VOTRE APPAREIL
Retirez l'emballage extérieur et intérieur.
Avant de connecter l'appareil à la source d'alimentation, laissez-le reposer pendant environ 2 heures.
Cela réduira la possibilité d'un dysfonctionnement du système de refroidissement lié à la manipulation
pendant le transport.
Nettoyez la surface intérieure avec de l'eau tiède à l'aide d'un chiffon doux.
Installez la poignée sur la porte si elle n'est pas déjà attachée. (Voir page 23.)
INSTALLATION DE VOTRE APPAREIL
L'appareil est conçu pour une installation intégrée ou encastrée ou autonome pour une utilisation
intérieure ou extérieure.
ATTENTION: Cet appareil n'est pas conçu pour le stockage de médicaments ou d'autres produits
médicaux.
Placez votre appareil sur un sol suffisamment solide pour le supporter lorsqu'il est complètement
chargé. Pour mettre l'appareil à niveau, ajustez les pieds de nivellement avant.
Pour une installation autonome, 5 po (127 mm) d'espace entre l'arrière et les côtés de l'appareil et 4
po (102 mm) en haut sont suggérés, ce qui permet une bonne circulation de l'air pour refroidir le
compresseur et le condenseur. Même pour une installation intégrée, il est indispensable de conserver
6,35 mm (1/4 po) d’espace de chaque côté et en haut et 51 mm (2 po) à l’arrière. Veillez à ce que
l'évent situé à l'avant de l'appareil ne soit jamais recouvert ou bloqué de quelque manière que ce soit.
REMARQUE: Il est recommandé de ne pas installer l'appareil à proximité d'un four, d'un radiateur ou
d'une autre source de chaleur. La lumière directe du soleil peut affecter le revêtement acrylique et les
sources de chaleur peuvent augmenter la consommation électrique. Ne pas installer dans un endroit
où la température tombera en dessous de 7 ° C (44 ° F). Pour des performances optimales, n'installez
pas l'appareil derrière une porte d'armoire ou ne bloquez pas la grille de la base.
Évitez de placer l'appareil dans des endroits humides.
Branchez l'appareil dans une prise murale exclusive et correctement mise à la terre.
CONNEXION ÉLECTRIQUE
Cet appareil doit être correctement mis à la terre pour votre sécurité. Le cordon d'alimentation de cet
appareil est équipé d'une prise à trois broches qui se raccorde aux prises murales à trois broches
standard afin de minimiser les risques de choc électrique.
Ne coupez ou ne retirez en aucun cas la troisième broche (mise à la terre) du cordon d'alimentation
fourni. Pour votre sécurité personnelle, cet appareil doit être correctement mis à la terre. Toute question
concernant l'alimentation et / ou la mise à la terre doit être adressée à un électricien agréé ou à un centre
de service agréé.
Cet appareil nécessite une prise électrique standard à trois broches avec mise à la terre de 115/120 volts
CA ~ 60 Hz. Faites vérifier la prise murale et le circuit par un électricien qualifié pour vous assurer que la
prise est correctement mise à la terre. Lorsqu'une prise murale standard à deux broches est rencontrée, il
vous incombe de la remplacer par une prise murale à trois broches correctement mise à la terre.
AVERTISSEMENT
Une mauvaise utilisation de la prise mise à la terre peut entraîner un risque de choc électrique. Si
le cordon d'alimentation est endommagé, faites-le remplacer par un électricien qualifié ou un
centre de service agréé.
20
Pour éviter toute blessure accidentelle, le cordon doit être attac derrière l’appareil et ne pas être
exposé ou suspendu.
L'appareil doit toujours être branché sur sa propre prise électrique ayant une tension nominale
correspondant à celle indiquée sur l'appareil. Cela offre les meilleures performances et empêche
également la surcharge des circuits de câblage de la maison, ce qui pourrait provoquer un risque de
surchauffe. Ne débranchez jamais l'appareil en tirant sur le cordon d'alimentation. Toujours saisir
fermement la fiche et la retirer directement du réceptacle. Réparez ou remplacez immédiatement tous les
cordons d'alimentation usés ou endommagés. N'utilisez pas de cordon présentant des fissures ou des
dommages par abrasion sur toute sa longueur ou à chaque extrémité. Lorsque vous déplacez l'appareil,
faites attention à ne pas endommager le cordon d'alimentation.
RALLONGE
En raison de dangers potentiels dans certaines conditions, il est fortement recommandé de ne pas utiliser
de rallonge avec cet appareil. Cependant, si vous devez utiliser une rallonge, il est absolument
nécessaire que ce soit une rallonge de type mise à la terre à 3 fils homologuée UL / CUL avec une fiche
et une prise de terre et que la tension électrique du cordon soit de 115 volts. et au moins 10 ampères.
INVERSION DE L'OUVERTURE DE LA PORTE DE VOTRE APPAREIL
Cet appareil a la capacité d'ouvrir la porte du côté gauche ou du côté droit. L'unité vous est livrée avec la
porte s'ouvrant du côté gauche. Si vous souhaitez inverser le sens d'ouverture, veuillez suivre les
instructions d'inversion indiquées ci-dessous.
NOTE: Toutes les pièces enlevées doivent être sauvegardées pour permettre d'inverser la porte.
1. Retirez la charnière inférieure (2) en dévissant les quatre vis de blocage (1). Veillez à bien tenir la
porte après avoir retiré les vis. (Fig. 1)
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16
  • Page 17 17
  • Page 18 18
  • Page 19 19
  • Page 20 20
  • Page 21 21
  • Page 22 22
  • Page 23 23
  • Page 24 24
  • Page 25 25
  • Page 26 26
  • Page 27 27
  • Page 28 28

Summit CL67ROSB Le manuel du propriétaire

Taper
Le manuel du propriétaire
Ce manuel convient également à

dans d''autres langues