Maytag MFW2055YEM00 User Instructions

THANK YOU for purchasing this high-quality product. If you should experience a problem not covered in TROUBLESHOOTING,

please visit our website at www.maytag.com for additional information. If you still need assistance, call us at 1-800-688-9900.

In Canada, visit our website at www.maytag.ca or call us at 1-800-807-6777.

You will need your model and serial number, located on the inside wall of the refrigerator compartment.

Para obtener acceso a "lnstrucciones para el usuario del refrigerador" en espa_ol, o para obtener informaci6n adicional acerca de

su producto, visite: www.maytag.com.

Necesitara su nQmerode modelo y de serie, ubicado en el interior del compartimiento del refrigerador.

Table of Contents / Table des mati res

REFRIGERATOR SAFETY ........................................................ 2

Proper Disposal of Your Old Refrigerator .............................. 2

INSTALLATION INSTRUCTIONS ............................................. 3

Unpack the Refrigerator ......................................................... 3

Location Requirements .......................................................... 3

Remove and Replace Refrigerator

Doors and Drawer Front ......................................................... 4

Electrical Requirements .......................................................... 6

Water Supply Requirements ................................................... 6

Connect the Water Supply ..................................................... 6

Handle Installation .................................................................. 8

Door Closing and Door Alignment ......................................... 8

FILTERS AND ACCESSORIES ................................................. 9

Install Air Filter......................................................................... 9

Install Produce Preserver ....................................................... 9

Accessories ........................................................................... 10

REFRIGERATOR USE............................................................. 10

Opening and Closing Doors ................................................. 10

Using the Controls ................................................................ 10

REFRIGERATOR FEATURES ................................................. 12

Refrigerator Shelves ...............................................................

Pantry Drawer ....................................................................... 12

Crisper ................................................................................... 13

DOOR FEATURES ................................................................... 13

Condiment Bins .................................................................... 13

Fresh Bin ............................................................................... 13

Half-Height Bin ..................................................................... 14

REFRIGERATOR CARE .......................................................... 14

Cleaning ................................................................................ 14

Changing the Light Bulbs ..................................................... 14

TROUBLESHOOTING ............................................................. 15

Operation .............................................................................. 15

Noise .................................................................................... 16

Temperature and Moisture ................................................... 17

Ice and Water ........................................................................ 18

Doors ..................................................................................... 19

WAR RANTY ............................................................................. 20

SI_CURITI_ DU RI_FRIGI_RATEUR ......................................... 22

Mise au rebut adequate de votre vieux refrig6rateur ...........23

INSTRUCTIONS D'INSTALLATION ....................................... 23

Deballage du refrig6rateu ..................................................... 23

Exigences d'emplacement ................................................... 24

Retrait et reinstallation des portes du

refrig6rateur et de I'avant du tiroir ........................................ 24

Specifications electriques ..................................................... 27

Specifications de I'alimentation en eau................................ 27

Raccordement a I'alimentation en eau ................................. 27

Installation de la poignee ...................................................... 29

Fermeture et alignement de la porte .................................... 29

FILTRES ET ACCESSOIRES .................................................. 30

Installation du filtre a air........................................................ 30

Installation du conservateur pour produits frais ................... 31

Accessoires ........................................................................... 32

UTILISATION DU RI_FRIGI_RATEUR .................................... 32

Ouverture et fermeture des portes ....................................... 32

Utilisation des commandes .................................................. 32

CARACTI_RISTIQUES DU RI_FRIGI_RATEUR ...................... 34

Tablettes du r6frigerateur ..................................................... 34

Garde-manger ....................................................................... 34

Bac & legumes ...................................................................... 35

CARACTI_RISTIQUES DE LA PORTE ................................... 35

Balconnets a condiments ..................................................... 35

Balconnet frafcheur ............................................................... 35

Balconnet mi-hauteur ........................................................... 36

ENTRETIEN DU RI_FRIGI_RATEUR ....................................... 36

Nettoyage .............................................................................. 36

Remplacement des ampoules d'eclairage ........................... 36

DI_PANNAGE ........................................................................... 37

Fonctionnement .................................................................... 37

Bruit ....................................................................................... 38

Temperature et humidite ...................................................... 39

Glagons et eau...................................................................... 40

Portes .................................................................................... 41

GARANTIE ............................................................................... 42

W10444179A

REFRIGERATOR SAFETY

Your safety and the safety of others are very important.

We have provided many important safety messages in this manual and on your appliance. Always read and obey all safety

messages.

This is the safety alert symbol.

This symbol alerts you to potential hazards that can kill or hurt you and others.

All safety messages will follow the safety alert symbol and either the word "DANGER" or "WARNING."

These words mean:

You can be killed or seriously injured if you don't immediately

follow instructions.

You can be killed or seriously injured if you don't follow

instructions.

All safety messages will tell you what the potential hazard is, tell you how to reduce the chance of injury, and tell you what can

happen if the instructions are not followed.

IMPORTANT SAFETY INSTRUCTIONS

WARNING: To reduce the risk of fire, electric shock, or injury when using your refrigerator, follow these basic precautions:

• Plug into a grounded 3 prong outlet.

• Do not remove ground prong.

• Do not use an adapter.

• Do not use an extension cord.

[] Disconnect power before servicing.

• Replace all parts and panels before operating.

• Remove doors from your old refrigerator.

• Use nonflammable cleaner.

• Keep flammable materials and vapors, such as gasoline,

away from refrigerator.

• Use two or more people to move and install refrigerator.

• Disconnect power before installing ice maker (on ice maker

kit ready models only).

• Use a sturdy glass when dispensing ice (on some models).

• Do not hit the refrigerator glass doors (on some models).

SAVE THESE INSTRUCTIONS

Proper Disposal of Your Old Refrigerator

Suffocation Hazard

Remove doors from your old refrigerator.

Failure to do so can result in death or brain damage.

Before You Throw Away Your Old Refrigerator or Freezer:

• Takeoff the doors.

• Leave the shelves in place so that children may not easily

climb inside.

IMPORTANT: Child entrapment and suffocation are not problems

of the past. Junked or abandoned refrigerators are still dangerous

- even if they will sit for "just a few days." If you are getting rid of

your old refrigerator, please follow these instructions to help

prevent accidents.

Important information to know about disposal of

refrigerants:

Dispose of refrigerator in accordance with Federal and Local

regulations. Refrigerants must be evacuated by a licensed,

EPA certified refrigerant technician in accordance with

established procedures.

2

INSTALLATION INSTRUCTIONS

Excessive Weight Hazard

Use two or more people to move and install

refrigerator.

Failure to do so can result in back or other injury.

Remove the Packaging

• Remove tape and glue residue from surfaces before turning

on the refrigerator. Rub a small amount of liquid dish soap

over the adhesive with your fingers. Wipe with warm water

and dry.

• Do not use sharp instruments, rubbing alcohol, flammable

fluids, or abrasive cleaners to remove tape or glue. These

products can damage the surface of your refrigerator. For

more information, see "Refrigerator Safety."

• Dispose of/recycle all packaging materials.

When Moving Your Refrigerator:

Your refrigerator is heavy. When moving the refrigerator for

cleaning or service, be sure to cover the floor with

cardboard or hardboard to avoid floor damage. Always pull

the refrigerator straight out when moving it. Do not wiggle or

"walk" the refrigerator when trying to move it, as floor

damage could occur.

Clean Before Using

After you remove all of the packaging materials, clean the inside

of your refrigerator before using it. See the cleaning instructions

in "Refrigerator Care."

important information to know about glass shelves

and covets:

Do not clean glass shelves or covers with warm water when

they are cold. Shelves and covers may break if exposed to

sudden temperature changes or impact, such as bumping.

Tempered glass is designed to shatter into many small,

pebble-size pieces. This is normal. Glass shelves and covers

are heavy. Use both hands when removing them to avoid

dropping.

Explosion Hazard

Keep flammable materials and vapors, such as

gasoline, away from refrigerator.

Failure to do so can result in death, explosion, or fire.

To ensure proper ventilation for your refrigerator, allow for a V2"

(1.25 cm) of space on each side and at the top. Allow for a 1"

(2.54 cm) space behind the refrigerator. Ifyour refrigerator has an

ice maker, allow extra space at the back for the water line

connections. When installing your refrigerator next to a fixed wall,

leave a 2" (5.08 cm) minimum space between the refrigerator and

wall to allow the door to swing open.

NOTE: This refrigerator is intended for use in a location where the

temperature ranges from a minimum of 55°F (13°C) to a

maximum of 110°F (43°C). The preferred room temperature range

for optimum performance, which reduces electricity usage and

provides superior cooling, is between 60°F (15°C) and 90°F

(32°C). It is recommended that you do not install the refrigerator

near a heat source, such as an oven or radiator.

1/2" (1.25 cm)

]1

I II I

7¢

2" (5.08 cm)

Depending on the width of your door opening, it may be

necessary to remove the refrigerator doors to move the

refrigerator into your home.

IMPORTANT:

• If the refrigerator was previously installed and you are moving

it out of the home, before you begin, turn the refrigerator

control OFF, and unplug the refrigerator or disconnect power.

Remove food and any adjustable door or utility bins from

doors.

• Keep the refrigerator doors closed until you are ready to lift

them free from the cabinet. Provide additional support for the

refrigerator door while the hinges are being removed. Do not

depend on the door gasket magnets to hold the door in place

while you are working.

• All graphics referenced in the following instructions are

included later in this section after "Final Steps."

TOOLS NEEDED: 5Ae",3/8",and V4"hex head socket wrenches,

Torx®tT27 screwdriver, #2 Phillips screwdriver, and a flat-blade

screwdriver.

Remove Doors and Hinges

1. Unplug refrigerator or disconnect power.

2. Remove the base grille. Grasp the grille firmly and pull it

toward you.

3. Starting with the right-hand side door, remove the parts for

the top hinge as shown inTop Hinge graphic. Lift the

refrigerator door from the bottom hinge pin.

4. Remove the hinge pin cover from the bottom hinge pin and

keep it for later use. See Bottom Hinge graphic.

5. Remove top hinge cover from left side refrigerator door.

6. Remove the parts for the top hinge as shown in Top Hinge

graphic. Lift the left-hand side door from the bottom hinge

pin.

NOTE: On some models, remove the hinge pin cover from

the bottom hinge pin and keep it for later use. See Bottom

Hinge graphic.

Replace Doors and Hinges

1. Assemble the parts for the top hinges as shown in Top Hinge

graphic. Do not tighten the screws completely.

2. Replace the parts for the bottom hinge as shown in Bottom

Hinge graphic. Tighten screws. Replace the refrigerator door.

NOTE: Provide additional support for the refrigerator door

while the hinges are being moved. Do not depend on the door

gasket magnets to hold the door in place while you are

working.

3. Align the door so that the bottom of the refrigerator doors

align evenly with the top of the freezer drawer. Tighten all

screws.

Remove and Replace Freezer Drawer Front

IMPORTANT: Two people may be required to remove and

replace the freezer drawer. Graphics are included later in this

section.

To remove drawer front:

1. Open the freezer drawer to full extension.

2. Loosen the four screws attaching the drawer glides to the

drawer front. See Drawer Front Removal graphic.

NOTE: Loosen screws three to four turns. Keep the screws in

the drawer front.

3. Lift drawer front upward and off the screws. See Drawer Front

Removal graphic.

4. The refrigerator leveling/roller assembly protrudes from each

side of the cabinet base. Remove the three screws attaching

each assembly, and remove the assemblies. See Leveling/

Roller Assembly graphic.

To replace drawer front:

1. Align the leveling/roller assembly with the holes on each side

of the refrigerator cabinet. Using the screws removed,

reinstall the assemblies to the cabinet base. Tighten the

screws completely.

2. Slide the drawer glides out of the freezer compartment. Insert

the screws in the top of the drawer front into the slots in the

drawer brackets. See Drawer Front Replacement graphic.

3. Pull the drawer brackets toward you to position the two

screws in the bottom of the drawer front into the brackets

and completely tighten the four screws. See Drawer Front

Replacement graphic.

4. Replace the base grille.

Final Steps

Electrical Shock Hazard

Plug into a grounded 3 prong outlet.

Do not remove ground prong.

Do not use an adapter.

Do not use an extension cord.

Failure to follow these instructions can result in death,

fire, or electrical shock.

1. Plug into a grounded 3 prong outlet.

2. Return all removable parts to doors and drawer and food to

refrigerator and freezer.

4. Replace the top hinge covers.

t(t4qOEX is a registered trademark of Saturn Fasteners, Inc.

Top Hinges

A. Hinge Cover Screw

B. Top Hinge Cover

C. 5/16" Hex-Head Hinge Screws

D. Top Hinge

Bottom Hinges

B

C

A. Hinge Pin Cover

B. Bottom Hinge

C. Hinge Screws

Leveling/Roller Assembly

A. Assembly Screws

A. Loosen 4 Door Bracket Screws

¸ui oem : ts

Electrical Shock Hazard

Plug into a grounded 3 prong outlet.

Do not remove ground prong.

Do not use an adapter.

Do not use an extension cord.

Failure to follow these instructions can result in death,

fire, or electrical shock.

Before you move your refrigerator into its final location, it is

important to make sure you have the proper electrical

connection.

Recommended Grounding Method

A 115 volt, 60 Hz., AC only 15- or 20-amp fused, grounded

electrical supply is required. It is recommended that a separate

circuit serving only your refrigerator be provided. Use an outlet

that cannot be turned off by a switch. Do not use an

extension cord.

NOTE: Before performing any type of installation, cleaning, or

removing a light bulb, turn Cooling OFF, and then disconnect the

refrigerator from the electrical source. When you are finished,

reconnect the refrigerator to the electrical source and turn

Cooling ON. See "Using the Controls."

A cold water supply with water pressure between 30 and 120 psi

(207 and 827 kPa) is required to operate the water dispenser and

ice maker. Ifyou have questions about your water pressure, call a

licensed, qualified plumber.

Reverse Osmosis Water Supply

IMPORTANT: The pressure of the water supply coming out of a

reverse osmosis system going to the water inlet valve of the

refrigerator needs to be between 30 and 120 psi (207 and

827 kPa).

If a reverse osmosis water filtration system is connected to your

cold water supply, the water pressure to the reverse osmosis

system needs to be a minimum of 40 to 60 psi (276 to 414 kPa).

If the water pressure to the reverse osmosis system is less than

40 to 60 psi (276 to 414 kPa):

• Check to see whether the sediment filter in the reverse

osmosis system is blocked. Replace the filter if necessary.

• Allow the storage tank on the reverse osmosis system to refill

after heavy usage. The tank capacity could be too low to

keep up with the requirements of the refrigerator.

• If your refrigerator has a water filter, it may further reduce the

water pressure when used in conjunction with a reverse

osmosis system. Remove the water filter. See "Water

Filtration System."

If you have questions about your water pressure, call a licensed,

qualified plumber.

:tS,,.} } u

Read all directions before you begin.

IM PORTANI"."

• All installations must meet local plumbing code requirements.

• Use copper tubing or Whirlpool supply line, Part Number

8212547RP, and check for leaks.

• Install copper tubing only in areas where the temperatures

will remain above freezing.

TOOLS NEEDED:

Gather the required tools and parts before starting installation.

Read and follow the instructions provided with any tools listed

here.

• Flat-blade screwdriver • V4"Nut driver

• 7Ad'and V2"Open-end or two • V4"Drill bit

adjustable wrenches

• Cordless drill

NOTE: Your refrigerator dealer has a kit available with a V4"

(6.35 mm) saddle-type shutoff valve, a union, and copper tubing.

Before purchasing, make sure asaddle-type valve complies with

your local plumbing codes. Do not use a piercing-type or 3Ad'

(4.76 mm) saddle valve which reduces water flow and clogs more

easily.

Connect to Water Line

Style 1

1. Unplug refrigerator or disconnect power.

2. Turn OFF main water supply. Turn ON nearest faucet long

enough to clear line of water.

3. Locate a 1/2"to 1V4" (1.25 cm to 3.18 cm) vertical cold water

pipe near the refrigerator.

IMPORTANT:

• Make sure it is a cold water pipe.

• Horizontal pipe will work, but drill on the top side of the

pipe, not the bottom. This will help keep water away from

the drill and normal sediment from collecting in the valve.

4. Determine the length of copper tubing you need. Measure

from the connection on the lower left rear of refrigerator to the

water pipe. Add 7 ft (2.1 m) to allow for cleaning. Use V4"

(6.35 mm) O.D. (outside diameter) copper tubing. Be sure

both ends of copper tubing are cut square.

5. Using a cordless drill, drill a V4"hole in the cold water pipe

you have selected.

G,, B C

6=

A. Cold water pipe

B. Pipe clamp

C. Copper tubing

D. Compression nut

E. Compression sleeve

F. Shutoff valve

G. Packing nut

Fasten the shutoff valve to the cold water pipe with the pipe

clamp. Be sure the outlet end is solidly in the V4"(6.35 mm)

drilled hole in the water pipe and that the washer is under the

pipe clamp. Tighten the packing nut. Tighten the pipe clamp

screws slowly and evenly so washer makes a watertight seal.

Do not overtighten or you may crush the copper tubing.

6

7. Slip the compression sleeve and compression nut onto the

copper tubing as shown. Insert the end of the tubing into the

outlet end squarely as far as it will go. Screw compression nut

onto outlet end with adjustable wrench. Do not overtighten.

8. Place the free end of the tubing in a container or sink, and

turn ON the main water supply. Flush the tubing until water is

clear. Turn OFF the shutoff valve on the water pipe. Coil the

copper tubing.

Style 2

1. Unplug refrigerator or disconnect power.

2. Remove and discard the black nylon plug from the gray water

tube on the rear of the refrigerator.

3. Thread the provided nut onto the water valve as shown.

NOTE: Tighten the nut by hand. Then tighten it with a wrench

two more turns. Do not overtighten.

Style 2

1. Unplug refrigerator or disconnect power.

2. Remove and discard the black nylon plug from the gray water

tube on the rear of the refrigerator.

3. If the gray water tube supplied with the refrigerator is not long

enough, a 1/4"x 1/4"(6.35 mm x 6.35 mm) coupling is needed

in order to connect the water tubing to an existing household

water line. Thread the provided nut onto the coupling on the

end of the copper tubing.

NOTE: Tighten the nut by hand. Then tighten it with a wrench

two more turns. Do not overtighten.

A

I/ III

B

A.Bulb

B.Nut (provided)

4. Turn shutoff valve ON.

5. Check for leaks. Tighten any nuts or connections (including

connections at the valve) that leak.

Connect to Refrigerator

Style 1

1. Unplug refrigerator or disconnect power.

2. Attach the copper tube to the valve inlet using a compression

nut and sleeve as shown. Tighten the compression nut. Do

not overtighten.

3. Use the tube clamp on the back of the refrigerator to secure

the tubing to the refrigerator as shown. This will help avoid

damage to the tubing when the refrigerator is pushed back

against the wall.

4. Turn shutoff valve ON.

5. Check for leaks. Tighten any connections (including

connections at the valve) or nuts that leak.

D

E

A B C D E F G

A. Refrigerator water tubing

B. Nut (provided)

C. Bulb

D. Coupling (provided)

E.Ferrule (purchased)

F Nut (purchased)

G. Household water fine

4. Turn shutoff valve ON.

5. Check for leaks. Tighten any nuts or connections (including

connections at the valve) that leak.

Complete the Installation

Electrical Shock Hazard

Plug into a grounded 3 prong outlet.

Do not remove ground prong.

Do not use an adapter.

Do not use an extension cord.

Failure to follow these instructions can result in death,

fire, or electrical shock.

1. Plug into a grounded 3 prong outlet.

2. Flush the water system. See "Water Dispenser."

NOTE: Allow 24 hours to produce the first batch of ice. Discard

the first three batches of ice produced. Allow 3 days to

completely fill ice container.

6.

A. Tube clamp

B. Tube clamp screw

C. Copper tubing

D. Compression nut

E. Valve inlet

On models with ice makers, the ice maker is equipped with a

built-in water strainer. If your water conditions require a

second water strainer, install it in the 1/4"(6.35 mm) water line

at either tube connection. Obtain a water strainer from your

nearest appliance dealer.

Parts Included: Handles (3)

Install Door Handles

1. Remove the handles from the packaging inside the

refrigerator.

NOTE: To avoid damaging the handles, place them on a

towel or other soft surface.

2.

Place the keyhole slots in the handle over the shoulder

screws (preinstalled on the door). Apply firm pressure on the

handle to slide it down onto the shoulder screws.

NOTE: Do not push the handle toward the door; this can

damage the door. Apply only downward pressure.

3. Repeat the previous steps to install the adjacent door handle.

Install Drawer Handle

1. Place the keyhole slots in the handle over the shoulder

screws (preinstalled on the drawer). Slide the handle firmly to

the right to fully engage the shoulder screws in the keyhole

slots.

NOTE: Do not push the handle toward the drawer; this can

damage the drawer.

2. Save all instructions.

Remove the Handles

Refrigerator Door

• Lift the handle directly upward, and pull it off of the door.

• If necessary, use a Phillips screwdriver to remove the

shoulder screws from the door.

Freezer Drawer

• Slide the handle to the left to disengage the keyhole slot from

the shoulder screws, and pull it off of the drawer.

• If necessary, use a Phillips screwdriver to remove the

shoulder screws from the drawer.

IMPORTANT: To comply with American Disabilities Act (ADA)

guidelines, fully retract the rollers into the cabinet to lower the

refrigerator.

Door Closing

The base grille covers the leveling screws and roller assemblies

located at the bottom of the refrigerator cabinet below the freezer

drawer. Before making adjustments, remove the base grille and

move the refrigerator to its final location.

1. Remove the base grille. Grasp the grille firmly and pull it

toward you.

2. Move the refrigerator to its final location.

NOTE: To allow the refrigerator to roll easier, raise the leveling

legs off the floor by turning the leveling screws

counterclockwise. The front rollers will be touching the floor.

3. So the doors will close easier, use a V4"hex driver to turn both

leveling screws clockwise. This will raise the front of the

refrigerator tilting it slightly downward to the rear. Turn both

leveling screws the same amount.

NOTE: Having someone push against the top of the

refrigerator takes some weight off the leveling screws. This

makes it easier to turn the screws.

A. Leveling screw

4. Open both doors again to make sure they close as easily as

you like and that they stay closed. If not, tilt the refrigerator

slightly more to the rear by turning both leveling screws to the

right. It may take several more turns.

NOTE: To keep the refrigerator level, you should turn both

leveling screws the same amount.

5. Replace the base grille.

8

Door Alignment

If the space between the refrigerator doors and freezer drawer

looks uneven, you can adjust it using the following instructions:

1. Remove the top hinge cover.

2. Loosen the top hinge screws using a 5/16"socket or wrench.

3. Have someone hold the door in place or put a spacer

between the doors and drawer.

4. Tighten the top hinge screws once the door is in the desired

location.

5. Replace the top hinge cover.

FILTERS AND ACCESSORIES

{( s s}t_e x'_odes)

The air filter reduces the buildup of odors. This helps to maintain

a cleaner environment inside the refrigerator.

On some models, your refrigerator's accessory packet includes

an air filter, which must be installed prior to use. On some

models, the air filter is already installed at the factory.

Installing the Air Filter

Install the air filter behind the vented door, located along the rear

interior wall of the refrigerator compartment.

1. Remove the air filter from its packaging.

NOTE: An air filter status indicator is included with the air

filter. The indicator is not needed for models that display the

air filter status on the control panel.

2. Lift open the vented door.

3. Snap the filter into place.

Air Filter Status Indicator

The control panel displays the Air Filter status.

• GOOD - The air filter icon on the control lights up in BLUE.

• ORDER a replacement - The air filter icon on the control lights

up in YELLOW.

• REPLACE air filter - The air filter icon on the control lights up

in RED and "Replace Filter" will appear.

• EXPIRED - The air filter icon lights up in RED and "Replace

Filter" flashes on the control display.

After replacing the air filter, press and hold the AIR FILTER button

for 3 seconds. The filter icons will turn off. See "Using the

Control(s)." When the system is reset, the air filter icon will return

to its BLUE color and the words "Replace Filter" will disappear

from the display.

NOTE: At any filter status, pressing and holding the AIR FILTER

button for 3 seconds will reset the air filter status to Good and the

air filter icon will turn off.

Replacing the Air Filter

The disposable air filter should be replaced every 6 months, or

when the status indicator air filter icon turns on and starts

flashing when the refrigerator door is opened.

To order a replacement air filter, contact us. See "Accessories."

1. Remove the used air filter by squeezing in on the side tabs.

2. Install the new air filter and reset the status indicator using

the instructions in the previous section.

The accessory packet includes two produce preserver pouches,

which should be installed in a crisper drawer prior to use.

NOTE: For best performance, always use two pouches.

The produce preserver absorbs ethylene, to slow the ripening

process of many produce items. As a result, certain produce

items will stay fresh longer.

Ethylene production and sensitivity varies depending on the type

of fruit or ve¢ etable.

Produces Ethylene

Sensitivity

to Ethylene

High

Med.

Low

Very

Low

Broccoli

Lettuce

Spinach

Asparagus

Citrus fruit

Carrots

Grapes

Low Med. High Very

High

Berries

Canta-

loupe

Apples

Installing the Produce Preserver

CAUTION: IRRITANT

MAY IRRITATE EYES AND SKIN. DANGEROUS FUMES

FORM WHEN MIXED WITH OTHER PRODUCTS.

Do not mix with cleaning products containing ammonia,

bleach or acids. Do not get in eyes, on skin or clothing. Do

not breathe dust. Keep out of reach of children.

FIRST AID TREATMENT: Contains potassium

permanganate. If swallowed, call a Poison Control Center or

doctor immediately. Do not induce vomiting. If in eyes, rinse

with water for 15 minutes. If on skin, rinse with water.

Theproducepreserverpouchesshouldbeinstalledinthe

housing,locatedonthewallofoneofthecrisperdrawers.

Thefollowingaccessoriesareavailableforyourrefrigerator.To

order,contactusandaskforthepartnumbers.

IntheU.S.A.,visitourwebpagewww.maytag.com/accessories

orcall1-800-901-2042.

InCanada,visitourwebpagewww.maytagparts.ca

orcall1-800-807-6777.

StainlessSteelCleanerandPolish:

Order Part #4396095

Air Filter:

Order Part #W10311524 or AIR1

Ethylene Filter:

Order Part #W10346771A or FRESH1

1. Remove the Fresh Flow TM Produce Preserver pouches from

the packaging.

2. Lift up on the housing to remove it from the mounting tab.

3. Open the housing by pulling up and out on the back of the

top of the housing.

4. Place both pouches inside the housing, then snap the

housing back together.

5. Place the housing back on the mounting tab.

Installing the Status Indicator

The produce preserver comes with a status indicator, which

should be activated and installed at the same time the pouches

are installed.

1. Place the indicator face-down on a firm, flat surface.

2. Apply pressure to the bubble on the back of the indicator until

the bubble pops, to activate the indicator.

3. Slide open the cap on the top of the produce preserver

housing.

4. Place the indicator in the top of the housing, facing outward.

5. Slide the cap closed, and check that the indicator is visible

through the rectangular hole in the cap.

NOTE: The cap will not easily close if the indicator's bubble

has not been popped.

Replacing the Produce Preserver

The disposable pouches should be replaced every 6 months,

when the status indicator has completely changed from white to

red.

To order replacements, contact us. See "Accessories" for

ordering information.

1. Remove the used pouches from the produce preserver

housing.

2. Remove the used status indicator.

3. Install the replacement pouches and status indicator using

the instructions in the previous sections.

10

REFRIGERATOR USE

There are two refrigerator compartment doors. The doors can be

opened and closed either separately or together.

There is a vertically-hinged seal on the left refrigerator door.

• When the left side door is opened, the hinged seal

automatically folds inward so that it is out of the way.

• When both doors are closed, the hinged seal automatically

forms a seal between the two doors.

A

A. Hinged seal

IM PORTANT:

Wait 24 hours for your refrigerator to cool completely before

adding food. If you add food before the refrigerator has

cooled completely, your food may spoil.

NOTE: Adjusting the refrigerator and freezer temperature

controls to a colder than recommended setting will not cool

the compartments any faster.

The recommended setting should be correct for normal

household refrigerator use. The controls are set correctly

when milk or juice is as cold as you like and when ice cream

is firm.

• If the temperature is too warm or too cold in the refrigerator or

freezer, first check the air vents to be sure they are not

blocked before adjusting the controls.

Control Panel

Your refrigerator has an internal control panel, located at the top

of the refrigerator compartment.

I_ coo|ing r,ll

colde replace filter off 0 • colder

• freezer temp air filter speed cool moisture control lock fridgetemp •

To turn cooling back on, press and hold both the SPEED

COOL and MOISTURE CONTROL buttons, at the same time,

for 3 seconds. When cooling is on, the Cooling Off icon will

disappear and the previously selected settings will be

displayed.

Temperature Control

For your convenience, the temperature control is preset at the

factory. When you first install your refrigerator, make sure the

control is still set to the recommended setting as shown.

Recommended Setting "3 Lit Boxes"

Adjusting the Controls

If you need to adjust the temperature in either the refrigerator or

freezer compartment, use the settings listed in the following chart

as a guide.

• Press the TEMP button to display the desired number of

boxes from (1 box [least cold] to 5 boxes [coldest]).

NOTE: Except when starting the refrigerator, do not adjust the

control more than one setting at a time. Wait 24 hours between

adjustments for the temperature to stabilize.

CONDITION/REASON: ADJUSTMENT:

REFRIGERATOR too warm FRIDGE TEMP one

more box

FREEZER too warm/too little ice FREEZER TEMP one

more box

REFRIGERATOR too cold FRIDGE TEMP one less

box

FREEZER too cold FREEZER one less box

Cooling On/Off

Your refrigerator and freezer will not cool when cooling is

turned off.

• To turn cooling off, press and hold both the SPEED COOL

and MOISTURE CONTROL buttons, at the same time, for

3 seconds. When cooling is off, the Cooling Off icon will

appear on the display.

Additional Features

Door Open Alarm

• The Door Open icon lights up whenever either door is

opened.

0

When either door is open for 5 minutes and cooling is on, an

alert tone will sound three times, and the Door Open icon will

flash seven times. This pattern will repeat every 2 minutes

until all the doors are closed properly. The feature then resets

and will reactivate when either door is left open again for

5 minutes.

NOTES:

• To mute the audible alarm while keeping the doors open,

such as while cleaning the inside of the refrigerator, press any

button on the control panel. The alarm sound will be

temporarily turned off, but the Door Open icon will still be

displayed on the dispenser control panel.

• Both doors must be fully closed to turn off the Door Open

icon.

Speed Cool

The Speed Cool feature assists during times of high refrigerator

use, full grocery loads or temporarily warm room temperatures.

• Press SPEED COOL to set the freezer and refrigerator to the

coldest temperature settings. Press SPEED COOL again to

return to the selected temperature set point.

NOTES:

• The Speed Cool icon will be illuminated while the

refrigerator is in Speed Cool mode.

• The Speed Cool feature will turn off automatically after

24 hours.

_@

Moisture Control

The moisture control feature turns on a heater to help reduce

moisture on the door hinge seal. Use in humid environments or

when you notice moisture on the door hinge seal. The refrigerator

uses more energy when Moisture Control is on.

• To turn on the Moisture Control feature, press and hold

MOISTURE CONTROL for 3 seconds.

To turn off the Moisture Control feature, press and hold

MOISTURE CONTROL for 3 seconds.

11

Air Filter Status Light and Reset

The filter reset control allows you to restart the air filter status

tracking feature each time you replace the air filter. See "Install Air

Filter."

• Press and hold AIR FILTER for 3 seconds, to reset the air filter

status to Good. The air filter icon will turn blue.

Control Panel Lock

The control panel can be locked to avoid unintentional changes

to the settings.

NOTE: The lock feature does not shut off power to the

refrigerator. It simply deactivates the controls.

• Press and hold LOCK for 3 seconds to lock the controls. The

Lock icon will illuminate when the control panel is locked.

• Press and hold LOCK for 3 seconds again to unlock the

controls.

REFRIGERATOR FEATURES

NOTE: Your model may have some or all of these features.

important information to know about glass shelves

and covers:

Do not clean glass shelves or covers with warm water when

they are cold. Shelves and covers may break if exposed to

sudden temperature changes or impact, such as bumping.

Tempered glass is designed to shatter into many small,

pebble-size pieces. This is normal. Glass shelves and covers

are heavy. Use both hands when removing them to avoid

dropping.

i%" ......

The shelves in your refrigerator are adjustable to match your

individual storage needs.

Glass Shelves

To remove a shelf:

1. Remove items from the shelf.

2. Slide the shelf straight out to the stop.

3. Depending on your model, lift the back or front of the shelf

past the stop. Pull the shelf out the rest of the way.

To replace a shelf:

1. Slide the back of the shelf into the track in the wall of the

cabinet.

2. Guide the front of the shelf into the shelf track. Be sure to

slide the shelf in all the way.

Fold Away Shelf (on some models)

To retract the fold away shelf:

• Retract the fold away section of the shelf by holding the front

of the shelf with one hand and lifting up on the center front of

the shelf. Then push back and down on the shelf until it slides

beneath the back section of the shelf.

To replace the fold away shelf:

• Replace the fold away section of the shelf by holding the front

of the shelf with one hand and pulling the center of the shelf

until the fold away section is returned to its full shelf position.

Pantry Drawer

To remove and replace the pantry drawer:

1. Slide pantry drawer out to the stop.

2. Lift front of pantry drawer with one hand while supporting

bottom of drawer with other hand. Slide drawer out the rest of

the way.

3. Replace the drawer by sliding it back in fully past the drawer

stop.

Pantry Drawer Cover

To remove and replace the pantry drawer cover:

1. Remove the pantry drawer.

2. From underneath, push up on the glass cover and pull it out.

3. Replace the pantry drawer cover by lowering it into place.

4. Replace the pantry drawer.

Pantry Drawer Control

The amount of air flowing through the pantry drawer affects the

temperature inside the drawer.

The airflow control is located on the left side of the pantry drawer.

To adjust the airflow:

• Colder - Slide the control forward, toward the front of the

pantry drawer, the airflow is open.

12

• Cold - Slide the control all the way toward the rear of the

pantry drawer. The airflow is closed, as shown.

Crisper Drawers

To remove and replace the crisper drawer:

1. Slide the crisper drawer straight out to the stop. Lift the front

and slide the drawer out the rest of the way.

2. Replace the drawer by sliding the drawer in fully past the

stop.

DOOR FEATURES

NOTE: Your model may have some or all of these features.

Co td me :4

To remove and replace the condiment bins:

1. Tilt the bin by grabbing it and pulling outward.

2. Remove the bin by grabbing it and lifting it upward off the

glides.

3. Replace the bin by sliding it back onto the glides and then

push it closed.

Crisper Cover

To remove and replace the glass crisper cover:

1. Pull the glass straight out.

2. Replace the glass by pushing it straight in.

Crisper Humidity Control (on some models)

You can control the amount of humidity in the moisture-sealed

crisper. Adjust the control to any setting between LOW and

HIGH.

LOW (open) lets moist air out of the crisper for best storage of

fruits and vegetables with skins.

• Fruit: Wash, let dry and store in refrigerator in plastic bag or

crisper. Do not wash or hull berries until they are ready to use.

Sort and keep berries in original container in crisper, or store

in a loosely closed paper bag on a refrigerator shelf.

• Vegetables with skins: Place in plastic bag or plastic

container and store in crisper.

HIGH (closed) keeps moist air in the crisper for best storage of

fresh, leafy vegetables.

• Leafy vegetables: Wash in cold water, drain and trim or tear

off bruised and discolored areas. Place in plastic bag or

plastic container and store in crisper.

Bn

To remove and replace the fresh bin:

1. Open the bin by grabbing the top center lip of the bin and

tilting the bin outward.

2.

3=

Remove the bin by grabbing both sides of the bin and lifting

the bin upward off the glides.

Replace the bin by sliding it back into its tilted position on the

glides and then push it closed.

13

To remove and replace the half-height bin:

1. Tilt the bin by grabbing it and pulling outward.

2. Remove the bin by grabbing it and lifting it upward off the

glides.

3. Replace the bin by sliding it back onto the glides and then

push it closed.

REFRIGERATOR CARE

Explosion Hazard

Use nonflammable cleaner.

Failure to do so can result in death, explosion, or fire.

Both the refrigerator and freezer sections defrost automatically.

However, clean both sections about once a month to avoid

buildup of odors. Wipe up spills immediately.

IMPORTANT:

• Because air circulates between both sections, any odors

formed in one section will transfer to the other. You must

thoroughly clean both sections to eliminate odors. To avoid

odor transfer and drying out of food, wrap or cover foods

tightly.

• For stainless steel models, stainless steel is corrosion-

resistant and not corrosion-proof. To help avoid corrosion of

your stainless steel, keep your surfaces clean by using the

following cleaning instructions.

To Clean Your Refrigerator:

NOTE: Do not use abrasive or harsh cleaners such as window

sprays, scouring cleansers, flammable fluids, muriatic acid,

cleaning waxes, concentrated detergents, bleaches or cleansers

containing petroleum products on exterior surfaces (doors and

cabinet), plastic parts, interior and door liners or gaskets. Do not

use paper towels, scouring pads, or other harsh cleaning tools.

1. Unplug refrigerator or disconnect power.

2. Hand wash, rinse, and dry removable parts and interior

surfaces thoroughly. Use a clean sponge or soft cloth and a

mild detergent in warm water.

3. Clean the exterior surfaces.

Painted metal: Wash painted metal exteriors with a clean,

soft cloth or sponge and a mild detergent in warm water.

Rinse surfaces with clean, warm water and dry immediately

to avoid water spots.

Stainless steel: Wash stainless steel surfaces with a clean,

soft cloth or sponge and a mild detergent in warm water.

Rinse surfaces with clean, warm water and dry immediately

to avoid water spots.

NOTE: When cleaning stainless steel, always wipe in the

direction of the grain to avoid cross-grain scratching.

4. There is no need for routine condenser cleaning in normal

home operating environments. If the environment is

particularly greasy or dusty, or there is significant pet traffic in

the home, the condenser should be cleaned every 2 to

3 months to ensure maximum efficiency.

If you need to clean the condenser:

• Remove the base grille.

• Use a vacuum cleaner with asoft brush to clean the grille,

the open areas behind the grille and the front surface area

of the condenser.

5=

• Replace the base grille when finished.

Plug in refrigerator or reconnect power.

IM PC RTANI"."

• Not all appliance bulbs will fit your refrigerator. Be sure to

replace the bulb with an appliance bulb of the same size,

shape, and wattage.

• To ensure optimum refrigerator performance, replace light

bulbs as soon as they burn out.

Refrigerator Compartment Light

The lighting located at the top of the refrigerator compartment

never needs to be replaced. If the lights do not illuminate when

the door is opened call for assistance or service. In the U.S.A, call

1-800-253-1301. In Canada, call 1-800-807-6777.

Freezer Compartment Light (on some models)

1. Unplug the refrigerator or disconnect power.

2. Remove the light shield (on some models).

• Top of the freezer compartment - Slide the light shield

toward the back of the compartment to release it from the

light assembly.

3. Replace the burned-out bulb with an appliance bulb(s) no

greater than 25 watts.

4. Replace the light shield.

5. Plug in refrigerator or reconnect power.

14

TROUBLESHOOTING

First try the solutions suggested here or visit our website and reference FAQs (Frequently Asked Questions)

to possibly avoid the cost of a service call.

In the U.S.A., www.maytag.com In Canada, www.maytag.ca

Electrical Shock Hazard

Plug into a grounded 3 prong outlet.

Do not remove ground prong.

Do not use an adapter.

Do not use an extension cord.

Failure to follow these instructions can result in death,

fire, or electrical shock.

The refrigerator will not Check electrical supply Plug the power cord into a grounded 3 prong outlet.

operate .....................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................

Do not use an extension cord.

Make sure there is power to the outlet. Plug in a lamp to see

if the outlet is working.

Reset a tripped circuit breaker. Replace any blown fuses.

NOTE: If problems continue, contact an electrician.

Check controls Make sure cooling is turned on. See "Using the Controls."

New installation Allow 24 hours following installation for the refrigerator to

cool completely.

NOTE: Adjusting the temperature controls to the coldest

setting will not cool either compartment quicker.

The motor seems to run

too much

High efficiency compressor and fans

The room or outdoor temperature is

hot

A large amount of warm food has

been recently added

This is normal. Larger, more efficient refrigerators run longer.

It is normal for the refrigerator to work longer under these

conditions. For optimum performance, place the refrigerator

in an indoor, temperature controlled environment. See

"Location Requirements."

Warm food will cause the refrigerator to run longer until the

air cools to the desired temperature.

The door(s) are opened too frequently Warm air entering the refrigerator causes it to run more.

or for too long Open the door less often.

The refrigerator door or freezer drawer Make sure the refrigerator is level. See "Door Closing and

is ajar Door Alignment." Keep food and containers from blocking

the door.

The refrigerator control is set too cold Adjust the refrigerator control to a less cold setting until the

refrigerator temperature is as desired. See "Using the

Controls."

The door or drawer gasket is dirty, Clean or change the gasket. Leaks in the door seal will cause

worn, or cracked the refrigerator to run longer in order to maintain desired

temperatures.

15

The lights do not work A light bulb is loose in the socket or Tighten or replace the light bulb. See "Changing the Light

burned out Bulbs."

The dispenser light is set to OFF On some models, the dispenser light will operate only when

(on some models) a dispenser paddle is pressed. Ifyou want the dispenser light

to stay on continuously, see "Water and Ice Dispensers."

The refrigerator seems The compressor in your new refrigerator regulates

noisy temperature more efficiently while using less energy, and

Below are listed some normal operates quietly. Due to the reduction in operating noise you

sounds with explanations, may notice more intermittent noises.

Sound of the compressor High efficiency compressor and fans This is normal. Larger, more efficient

running longer than expected refrigerators run longer.

Pulsating/Whirring Fans/compressor adjusting to optimize performance during This is normal

normal compressor operation

Popping Contraction/expansion of inside walls, especially during This is normal

initial cool-down

Hissing/Dripping Flow of refrigerant, or flow of oil in the compressor This is normal

Vibration The refrigerator may not be steady Adjust the leveling screws and lower

the leveling foot firmly against the

floor. See "Door Closing and Door

Alignment."

Rattling/Banging Movement of the water lines against the refrigerator cabinet, Move excess water line away from the

or of items placed on top of the refrigerator cabinet refrigerator cabinet or fasten excess

tubing to the cabinet. See

"Connecting the Water," or remove

items from the top of the refrigerator.

Sizzling Water dripping on the heater during defrost cycle This is normal

Water running/Gurgling May be heard when ice melts during the defrost cycle and This is normal

water runs into the drain pan

Buzzing Heard when the water valve opens to fill the ice maker This is normal

Creaking/Cracking May be heard as ice is being ejected from the ice maker This is normal

mold

Ker-plunk May be heard when the ice falls into the ice storage bin This is normal

16

Temperature is too warm The refrigerator has just been installed Allow 24 hours following installation for the refrigerator to

cool completely.

Cooling is turned off Turn cooling on. See "Using the Controls."

The controls are not set correctly for Adjust the controls asetting colder. Check the temperature in

the surrounding conditions 24 hours. See "Using the Control(s)."

The door(s) are opened often or not Allows warm air to enter refrigerator. Minimize door openings

closed completely and keep doors fully closed.

A large load of food was recently Allow several hours for refrigerator to return to normal

added temperature.

Temperature is too cold in The refrigerator air vent(s) are blocked If the air vent located in the top, left, rear corner of the

the refrigerator/crisper refrigerator compartment is blocked by items placed directly

in front of it, the refrigerator will get too cold. Move items

away from the air vent.

The controls are not set correctly for Adjust the controls a setting warmer. Check the temperature

the surrounding conditions in 24 hours. See "Using the Control(s)."

The ice storage bin is not in the Make sure the ice storage bin is positioned so that it is not

correct position (on some models) blocking airflow.

Temperature is too cold in The control is not set correctly for the Adjust the control setting. See "Refrigerator Features."

the pantry drawers items stored in drawer

(on some models)

There is interior moisture The room is humid A humid environment contributes to moisture buildup.

buildup

NOTE: Some moisture The door(s) are opened often or not Allows humid air to enter the refrigerator. Minimize door

closed completely openings and close doors completely.

buildup is normal ..................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................

The door is blocked open Move food packages away from door.

A bin or shelf is in the way Push bin or shelf back into the correct position.

Storing liquid in open containers This adds humidity to the refrigerator interior. Keep all

containers tightly covered.

There is frost/ice buildup in The doors are opened often or left Minimize door openings and keep doors fully closed.

the freezer compartment open

Poor door seal Ensure door seals are making full contact with the

refrigerator cabinet to allow for an adequate seal.

Temperature controls are not set See "Using the Controls" for recommended temperature

correctly settings.

17

The ice maker is not The refrigerator is not connected to a Connect refrigerator to water supply and turn water shutoff

producing ice or is not water supply or the water supply valve fully open.

producing enough ice shutoff valve is not turned on

(on some models) ............................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................

There is a kink in the water source line A kink in the line can reduce water flow. Straighten the water

source line.

The ice maker is not turned on Make sure the ice maker is on.

See "Ice Maker and Ice Storage Bin."

The refrigerator has just been installed Wait 24 hours after ice maker installation for ice production

to begin. Wait 3 days for full ice production.

The refrigerator door is not closed Close the door firmly. If it does not close completely, see

completely "The doors will not close completely."

A large amount of ice was recently Allow 24 hours for ice maker to produce more ice.

removed

An ice cube is jammed in the ice Remove ice from the ejector arm with a plastic utensil.

maker ejector arm NOTE: On some models, press the lever which opens the ice

maker door to access the ejector arm.

A water filter is installed on the Remove the water filter and operate the ice maker. If ice

refrigerator volume improves, then the filter may be clogged or

incorrectly installed. Replace filter or reinstall it correctly.

A reverse osmosis water filtration This can decrease water pressure. See "Water Supply

system is connected to your cold Requirements."

water supply

The ice cubes are hollow The water shutoff valve is not fully Turn the water shutoff valve fully open.

or small (on some models) open

NOTE: This is an indication ...............................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................

There is a kink in the water source line A kink in the line can reduce water flow. Straighten the water

of low water pressure.

source line.

A water filter is installed on the Remove filter and operate ice maker. If ice quality improves,

refrigerator then the filter may be clogged or incorrectly installed.

Replace filter or reinstall it correctly.

A reverse osmosis water filtration This can decrease water pressure. See "Water Supply

system is connected to your cold Requirements."

water supply

Questions remain regarding water Call a licensed, qualified plumber.

pressure

18

Off-taste, odor or gray Recently installed or replaced Discard the ice and wash the ice storage bin. Flush the water

color in the ice or water plumbing connections. New plumbing system with 4 gal. (15 L) of water. Allow 24 hours for the ice

(on some models) connections can cause discolored or maker to make new ice, and discard the first 3 batches of ice

off-flavored ice and water produced.

The ice has been stored too long Discard ice. Wash ice storage bin. Allow 24 hours for ice

maker to make new ice.

The water has been stored too long Dispense at least 1 L of water per week to maintain a fresh

supply.

Odor from stored food has transferred Use airtight, moisture proof packaging to store food.

to the ice

There are minerals (such as sulfur) in A water filter may need to be installed to remove the

the water minerals.

There is a water filter installed on the Gray or dark discoloration in ice may indicate that the water

refrigerator filtration system needs additional flushing. Flush the water

system after installing and before using a new water filter.

See "Water and Ice Dispensers" for water filter flushing

instructions.

The water filter needs to be replaced Replace the disposable water filter at least every 6 months or

when indicated. See "Water Filtration System."

Water is leaking from the The water line connections were not See "Connecting the Water."

back of the refrigerator fully tightened

Recently removed the doors and did See "Refrigerator Doors and Drawer."

not fully tighten water line connection

Explosion Hazard

Use nonflammable cleaner.

Failure to do so can result in death, explosion, or fire.

The doors will not close The door is blocked open Move food packages away from door.

completely

A bin or shelf is in the way Push bin or shelf back into the correct position.

Recently installed Remove all packaging materials.

The doors are difficult to The door gaskets are dirty or sticky. Clean gaskets and contact surfaces with mild soap and

open warm water. Rinse and dry with soft cloth.

The doors appear to be The doors need to be aligned or the See "Door Closing and Door Alignment."

uneven refrigerator needs to be leveled

The doors do not open or The refrigerator tilt needs to be Adjust the refrigerator tilt. See "Door Closing and Door

close as expected adjusted Alignment."

19

MAYTAG ®MAJOR APPLIANCE WARRANTY

LIMITED WARRANTY

For one year from the date of purchase, when this major appliance is operated and maintained according to instructions attached to or

furnished with the product, Maytag brand of Whirlpool Corporation or Whirlpool Canada LP (hereafter "Maytag") will pay for factory

specified parts and repair labor to correct defects in materials or workmanship that existed when this major appliance was purchased.

Service must be provided by a Maytag designated service company. YOUR SOLE AND EXCLUSIVE REMEDY UNDER THIS LIMITED

WARRANTY SHALL BE PRODUCT REPAIR AS PROVIDED HEREIN. This limited warranty is valid only in the United States or Canada

and applies only when the major appliance is used in the country in which it was purchased. Proof of original purchase date is required

to obtain service under this limited warranty.

ITEMS EXCLUDED FROM WARRANTY

This limited warranty does not cover:

1. Replacement parts or repair labor if this major appliance is used for other than normal, single-family household use or when it is

used in a manner that is inconsistent to published user or operator instructions and/or installation instructions.

2. Service calls to correct the installation of your major appliance, to instruct you on how to use your major appliance, to replace or

repair house fuses, or to correct house wiring or plumbing.

3. Service calls to repair or replace appliance light bulbs, air filters or water filters. Consumable parts are excluded from warranty

coverage.

4. Damage resulting from accident, alteration, misuse, abuse, fire, flood, acts of God, improper installation, installation not in

accordance with electrical or plumbing codes, or use of products not approved by Maytag.

5. Cosmetic damage, including scratches, dents, chips or other damage to the finish of your major appliance, unless such damage

results from defects in materials or workmanship and is reported to Maytag within 30 days from the date of purchase.

6. Any food or medicine loss due to refrigerator or freezer product failures.

7. Pickup and delivery. This major appliance is intended to be repaired in your home.

8. Repairs to parts or systems resulting from unauthorized modifications made to the appliance.

9. Expenses for travel and transportation for product service if your major appliance is located in a remote area where service by an

authorized Maytag servicer is not available.

10. The removal and reinstallation of your major appliance if it is installed in an inaccessible location or is not installed in accordance

with Maytag's published installation instructions.

11. Replacement parts or repair labor on major appliances with original model/serial numbers that have been removed, altered or

cannot be easily determined.

12. Discoloration, rust, or oxidation of stainless steel surfaces.

DISCLAIMER OF IMPLIED WARRANTIES

IMPLIED WARRANTIES, INCLUDING ANY IMPLIED WARRANTY OF MERCHANTABILITY OR IMPLIED WARRANTY OF FITNESS FOR

A PARTICULAR PURPOSE, ARE LIMITED TO ONE YEAR OR THE SHORTEST PERIOD ALLOWED BY LAW. Some states and provinces

do not allow limitations on the duration of implied warranties of merchantability or fitness, so this limitation may not apply to you. This

warranty gives you specific legal rights, and you also may have other rights that vary from state to state or province to province.

LIMITATION OF REMEDIES; EXCLUSION OF INCIDENTAL AND CONSEQUENTIAL DAMAGES

YOUR SOLE AND EXCLUSIVE REMEDY UNDER THIS LIMITED WARRANTY SHALL BE PRODUCT REPAIR AS PROVIDED HEREIN.

MAYTAG SHALL NOT BE LIABLE FOR INCIDENTAL OR CONSEQUENTIAL DAMAGES. Some states and provinces do not allow the

exclusion or limitation of incidental or consequential damages, so these limitations and exclusions may not apply to you. This warranty

gives you specific legal rights, and you also may have other rights that vary from state to state or province to province.

If outside the 50 United States and Canada, contact your authorized Maytag dealer to determine if another warranty applies. 6/o8

In the U.S.A.:

Maytag Brand Home Appliances

Customer eXperience Center

553 Benson Road

Benton Harbor, MI 49022-2692

Please include a daytime phone number in your correspondence.

For additional product information, in the U.S.A., visit www.maytag.com

In Canada, visit www.maytag.ca

If you do not have access to the Internet and you need assistance using your product or you would like to schedule service, you may

contact Maytag at the number below.

Have your complete model number ready. You can find your model number and serial number on the label, located on the inside wall of

the refrigerator compartment.

For assistance or service in the U.S.A., call 1-800-688-9900. In Canada, call 1-800-807-6777.

If you need further assistance, you can write to Maytag with any questions or concerns at the address below:

In Canada:

Maytag Brand Home Appliances

Customer eXperience Centre

200 - 6750 Century Ave.

Mississauga, Ontario L5N 0B7

Please keep these User Instructions and the model number information for future reference.

20

La page est en cours de chargement...

Maytag MFW2055YEM00 User Instructions

Ce manuel convient également à

Maytag MFW2055YEM00 User Instructions

dans d''autres langues

Documents connexes

Autres documents