Shindaiwa C281TS Manuel utilisateur

1????

OPERATOR'S MANUAL

MANUEL D'UTILISATION

BEDIENUNGSANLEITUNG

MANUALE PER L'OPERATORE

ENGLISH

FRANÇAIS

DEUTSCH

ITALIANO

T281TS

C281TS

WARNING

READ THE INSTRUCTIONS CAREFULLY AND FOLLOW THE RULES FOR

SAFE OPERATION.

FAILURE TO DO SO COULD RESULT IN SERIOUS INJURY.

AVERTISSEMENT

LIRE ATTENTIVEMENT LES INSTRUCTIONS ET SUIVRE LES RÈGLES DE

SECURITÉ. LE NON-RESPECT DES RÈGLES DE SÉCURITÉ ENTRAÎNE UN

RISQUE DE BLESSURE GRAVE.

WARNUNG

LESEN SIE DIE BEDIENUNGSANLEITUNG SORGFÄLTIG DURCH, UND

BEFOLGEN SIE DIE SICHERHEITSREGELN. ANDERNFALLS BESTEHT DAS

RISIKO SCHWERER VERLETZUNGEN.

AVVERTENZA

LEGGERE E SEGUIRE ATTENTAMENTE LE ISTRUZIONI PER LAVORARE IN

CONDIZIONI DI MASSIMA SICUREZZA. LA MANCATA OSSERVANZA DELLE

ISTRUZIONI POTREBBE PROVOCARE LESIONI GRAVI.

1Cover

ENGLISH

(Original instructions)

OPERATOR'S MANUAL

GRASS-TRIMMER/BRUSHCUTTER

T281TS

C281TS

WARNING

READ THE INSTRUCTIONS CAREFULLY AND FOLLOW THE

RULES FOR SAFE OPERATION.

FAILURE TO DO SO COULD RESULT IN SERIOUS INJURY.

2

Contents

For safe use of your product............................................................................................... 3

Description.......................................................................................................................... 8

Before you start .................................................................................................................. 9

Packing list .................................................................................................................... 9

Assembly .......................................................................................................................9

Loop handle version .................................................................................................... 10

U-handle version.......................................................................................................... 10

Installation of shield ..................................................................................................... 10

Installing nylon line cutting head.................................................................................. 11

Adjusting the balance .................................................................................................. 11

Preparing the fuel ........................................................................................................ 12

Engine operation...............................................................................................................13

Starting the engine ...................................................................................................... 13

Stopping the engine..................................................................................................... 14

Trimming operation........................................................................................................... 15

Using shoulder harness............................................................................................... 16

Basic trimming operation with nylon line cutting head................................................. 16

Basic trimming operation with metal blade .................................................................. 18

Maintenance and care ...................................................................................................... 19

Servicing guidelines..................................................................................................... 19

Maintenance and care ................................................................................................. 19

Storage ........................................................................................................................26

Specifications.................................................................................................................... 27

Declaration of conformity .................................................................................................. 28

3

For safe use of your product

For safe use of your produc t

Important information

WARNING

Please ensure that you read the operator's manual before using your product.

About your operator's manual

 This manual contains necessary information about the assembly, operation, and maintenance of your product.

Please read it carefully and absorb its contents.

 Always keep your manual in a place where it is readily accessible.

 If you have lost your manual or it is damaged and no longer readable, please purchase a new one from your dealer.

 The units used in this manual are SI units (International System of Units). Figures in parentheses are reference val-

ues, and there may be a slight conversion error in some cases.

Failure to do so could lead to an accident or serious injury.

Intended use of this product

 This product is lightweight, high-performance, petrol engined unit designed for weed control, grass trimming and

brush cutting in areas difficult to control by any other means.

 Do not use this unit for any purpose other than aforementioned.

 The content of this manual may be changed without notice for the purpose of upgrades to the product. Some of the

illustrations used may differ from the product itself in order to make the explanations clearer.

 Please consult your dealer if anything is unclear or of concern.

Failure to do so could lead to an accident or serious injury.

Do not modify the product

 You must not modify the product.

To do so could lead to an accident or serious injury. Any malfunction resulting from a modification to the product will not be

covered by the manufacturer's warranty.

Do not use the product unless it has been checked and maintained

 You must not use the product unless it has been checked and maintained. Always ensure that the product is checked

and maintained on a regular basis.

Failure to do so could lead to an accident or serious injury.

Loaning or assigning your product

 When loaning your product to another party, ensure that the person borrowing the product receives the operator's

manual along with it.

 If you assign your product to another party, please enclose the operator's manual with the product when handing it

over.

Failure to do so could lead to an accident or serious injury.

Users of the product

 The product should not be used by:

 people who are tired

 people who have taken alcohol

 people who are on medication

 people who are pregnant

 people who are in poor physical condition

 people who have not read the operator's manual

 children

 Keep in mind that the operator or user is responsible for accidents or hazards occurring to other people or their prop-

erty.

Failure to observe these instructions could lead to an accident.

 The ignition system of this product generates electromagnetic fields during operation. Magnetic fields can cause

pacemaker interference or pacemaker failure. To reduce health risks, we recommend that pacemaker users consult

their physician and the pacemaker manufacturer before operating this product.

4

For safe use of your product

Vibration and cold

 It is believed that a condition called Raynaud's Phenomenon which affects the fingers of certain individuals may be

brought about by exposure to vibration and cold. Exposure to vibration and cold may cause tingling and burning,

followed by loss of colour and numbness in the fingers. The following precautions are strongly recommended be-

cause the minimum exposure which might trigger the ailment is unknown.

 Keep your body warm, especially the head and neck, feet and ankles, and hands and wrists.

 Maintain good blood circulation by performing vigorous arm exercises during frequent work breaks, and also by

not smoking.

 Limit the number of hours of operation. Try to fill each day with jobs where operating the trimmer or other hand-

held power equipment is not required.

 If you experience discomfort redness and swelling of the fingers, followed by whitening and loss of feeling, con-

sult your physician before exposing yourself further to cold and vibration.

Failure to observe these instructions could result in damage to your health.

Repetitive stress injuries

 It is believed that over-using the muscles and tendons of the fingers, hands, arms and shoulders may cause sore-

ness, swelling, numbness, weakness and extreme pain to the areas just mentioned. Certain repetitive hand activities

may put you at a high risk for developing a repetitive stress injury (RSI). To reduce the risk of RSI, do the following:

 Avoid using your wrist in a bent, extended or twisted position.

 Take periodic breaks to minimize repetition and rest your hands. Reduce the speed and force in which you do the

repetitive movement.

 Do exercises to strengthen hand and arm muscles.

 See a doctor if you feel tingling, numbness or pain in your fingers, hands, wrists or arms. The sooner RSI is diag-

nosed, the more likely permanent nerve and muscle damage can be prevented.

Failure to observe these instructions could result in damage to your health.

Proper training

 Do not permit operation without proper training and protective equipment.

 Be thoroughly familiar with the controls and proper use of unit.

 Know how to stop the unit and shut off the engine.

 Know how to unhook a harnessed unit quickly.

 Never allow anyone to use the unit without proper instruction.

Failure to observe these instructions could result in damage to your health.

Wear proper clothing.

 Secure hair so it is above shoulder length.

 Do not wear ties, jewellery, or loose, dangling clothing which could be caught in the

unit.

 Do not wear open toed footwear, or go bare-foot or barelegged.

Failure to observe these precautions could result in damage to your sight or hearing, or lead

to a serious injury.

Wear protective gear

 Always wear the following protective gear when working with the trimmer.

1. Head protection (helmet): Protects the head

2. Ear muffs or ear plugs: Protect the hearing

3. Safety goggles: Protect the eyes

4. Face shield: Protects the face

5. Safety gloves: Protect the hands from cold and vibration

6. Work clothes that fit (long sleeves, long trousers): Protect the body

7. Heavy duty, non-slip protective boots (with toecaps) or non-slip work shoes

(with toecaps): Protect the feet

8. Shin guards: Protect the legs

Failure to observe these precautions could result in damage to your sight or hearing, or

lead to a serious injury.

 When necessary, please use the protective gear below.

 Dust mask: Protects the breathing apparatus

 Bee net: To deal with attacks by bees

WARNING

5

For safe use of your product

Warning notices

Other indicators

Symbols

Environment of use and operation

 Do not use the product:

 under poor weather conditions.

 on steep slopes or in places which give no secure foothold and are thus slippery.

 at night or in dark places with poor visibility.

 When using the product on a gentle slope, work in a level, contour-like motion.

A serious injury could result if you fall or slip, or fail to operate the product correctly.

 For your own health and your safe and comfortable work, operate the machine within the air temperature range of

−5

o

C to 40

o

C.

Failure to observe these instructions could result in damage to your health.

Being prepared in case of an injury

 In the unlikely event of an accident or injury, please ensure that you are

prepared.

 First aid kit

 Towels and wipes (to stop any bleeding)

 Whistle or mobile phone (for calling outside help)

If you are unable to perform first aid or call for outside help, the injury could

worsen.

Put safety first in the case of fire or smoke

 If fire comes from the engine or smoke appears from any area other than the exhaust vent, first distance

yourself from the product to ensure your physical safety.

 Use a shovel to throw sand or other such material on the fire to prevent it from spreading, or put it out

with a fire extinguisher.

A panicked reaction could result in the fire and other damage becoming more extensive.

WARNING

DANGER WARNING CAUTION

This symbol accompanied by the

word "DANGER" calls attentions to

an act or a condition which will lead to

serious personal injury or death of op-

erators and bystanders.

This symbol accompanied by the

word "WARNING" calls attentions to

an act or a condition which can lead to

serious personal injury or death of op-

erators and bystanders.

"CAUTION" indicates a potentially

hazardous situation which, if not

avoided, may result in minor or mod-

erate injury.

Circle and slash sym-

bol means whatever is

shown is prohibited.

NOTE IMPORTANT

This enclosed message provides tips

for use, care and maintenance of the

product.

Framed text featuring the word "IM-

PORTANT" contains important infor-

mation about the use, checking,

maintenance and storage of the prod-

uct described in this manual.

Symbol form/shape Symbol description/applica-

tion

Symbol form/shape Symbol description/applica-

tion

Carefully read the operator's

manual

The maximum speed of the

cutting attachment shaft in

r/min

Wear eyes, ears and head

protection

Keep bystanders away 15 m

6

For safe use of your product

Wear foot protection and

gloves

Petrol and oil mixture

Emergency stop

Choke Control "Cold Start"

Position (Choke Closed)

Warning!

Thrown objects!

Choke Control "Run" Position

(Choke Open)

Warning, side thrust

Carburettor adjustment

- Idle speed

Usage without shield not per-

mitted

U-handle

Usage of metal blades not

permitted

Loop handle

Usage of nylon line cutting

head not permitted

Beware of high-temperature

areas

Do not use the product in plac-

es with poor ventilation

Guaranteed sound power lev-

el

Beware of fire Engine start

Beware of electric shocks

-

Purge bulb (Primer)

Symbol form/shape Symbol description/applica-

tion

Symbol form/shape Symbol description/applica-

tion

7

For safe use of your product

Safety decal(s)

 The safety decal shown below has been attached to the products described in this manual. Ensure that you understand what

the decal means before using your product.

 If the decal becomes unreadable due to wear and tear or damage, or peels off and is lost, please purchase a replacement decal

from your dealer and attach it in the location shown in the illustrations below. Ensure that the decal is readable at all times.

1. Safety decal (Part number 890617-43130)

2. Safety decal (Part number X505-002310)

8

Description

1. Angle transmission Having two gears to change the

angle of rotating axis.

2. Cutting attachment Nylon line cutting head for cutting

grass and weed.

3. Shield Device to protect the operator from accidental

contact with the cutting head and thrown objects.

4. Cut off knife Cut nylon line to adjust line length to prop-

er swath.

5. Shaft tube Part of the unit that provides a casing for

power transmission shaft.

6. Loop-handle Light weight, suitable for nylon line trim-

mer.

7. U-handle Having the configuration of a bicycle handle

bar to reduce working effort compared to a loop-handle.

8. Suspension point Device on which the harness can be

hooked.

9. Ignition switch "Slide switch" mounted on top of the

throttle trigger housing, move switch forward to RUN,

backward to STOP position.

10. Throttle trigger Activated by the operator's finger for

controlling the engine speed.

11. Throttle trigger lockout Locks throttle trigger in the

idling position until you have a proper grip with your right

hand around the handle.

12. Air cleaner cover Covers air filter.

13. Fuel tank cap For closing the fuel tank.

14. Fuel tank Contains fuel and fuel filter.

15. Starter handle Pull handle to start the engine.

16. Silencer cover Cover the silencer not to make operator

touch the hot surface of silencer.

17. Spark plug

18. Shoulder harness An adjustable strap to suspend unit.

19. Type and serial number

9

Before you start

Packing list

Assembly

 The following parts are packed separately in the packing box.

 When you have unpacked the box, please check the parts that it contains.

 Contact your dealer if anything is missing or broken.

1. Engine and shaft tube

2. Shield (for nylon line cutting head)

3. Shoulder harness

4. Loop handle

5. Nylon line cutting head

6. Operator's manual

7. Locking tool

8. Socket wrench

9. L-wrench

1. Engine and shaft tube

2. U-handle

3. Shield (for nylon line cutting head)

4. Shoulder harness

5. Nylon line cutting head

6. Operator's manual

7. Locking tool

8. Socket wrench

9. L-wrench

WARNING

 Read the operator's manual carefully to ensure that you assemble the product correctly.

Using a product that has been incorrectly assembled could lead to an accident or serious injury.

10

Before you start

Loop handle version

Loop handle assembly

Assemble loop handle (A) and bracket (C) to drive shaft assem-

bly.

Position handle in comfortable operating position and tighten

Bolts (B).

U-handle version

U-handle assembly

1. Install handle assembling bracket (upper) (A) in handle as-

sembling bracket (lower) (B) and fix handle by tightening

handle assembling bolt (C) lightly.

2. Adjust inclination of handle to adequate position (easy to op-

erate) and tighten firmly handle assembling bolt.

 To adjust the fixture bolt (D) proceed (As needed)

(1) Tighten the bolts until snug.

(2) Loosen the bolts 1

1

/

2

turn.

E: Arrow

F: To engine

3. To eliminate loosening of throttle wire (I), fix it to shaft tube

(H) (2 places) and to right hand U-handle (1 place) with wire

fixing clips (G).

Installation of shield

1. Fit shield (A) to mounting portion of angle transmission and

tighten 4 bolts (B).

E: Arrow F: To engine

CAUTION

 Install the handle to the engine side from the arrow

mark.

CAUTION

 Install the handle to the engine side from the arrow

mark.

11

Before you start

Installing nylon line cutting head

1. Insert locking tool (A) into a hole located on the right side of

angle transmission while forcing retainer spring to the left

side.

2. Insert locking tool further into blade retainer fixing slot (B) to

fix output shaft.

3. Thread nylon line cutting head (C) onto shaft (anticlockwise)

until it is tight.

4. Remove locking tool.

Adjusting the balance

Adjusting the shoulder harness

 The accompanying shoulder harness is suitable for people of

standard adult physique, who are 150 cm - 195 cm in height

and 60 cm - 140 cm in waist size.

 Use a shoulder harness when provided or when recommend-

ed in this manual. Adjust both harness and the suspension

point (A) on the unit so the unit hangs with the cutting attach-

ment a few centimetres above ground level (B).

 The cutting attachment and shield should be level in all direc-

tions. Harness the unit on the right side as shown.

 Slide suspension point up and down the tube to find the right

balance. Rotate the clamp to level the cutting attachment and

shield. Lock in position. If the suspension point is a free-spin-

ning type, the unit may tend to roll over sideways, however,

you should still level the attachment and shield on the front-to-

rear axis.

 Balancing and levelling, as above, may require relocation of

the clamp and readjustment of the harness straps. Also, each

type of cutting attachment and shield mounted on the unit may

require balancing.

CAUTION

 Fix output shaft securely using locking tool in order to

prevent it form rotating when nylon cutting head is

mounted.

WARNING

 This product is designed to fit a wide variety of body sizes, but may not be adjustable for extremely tall persons. Do

not use the unit if your feet can reach the cutting attachment when the unit is attached to the harness.

IMPORTANT

 A person's size can affect the balancing adjustment. Also the balancing procedure may not work with some units on some

persons. If the shoulder harness does not fit you or cannot be adjusted well, please ask your dealer for assistance.

Balance tool for a level plane of cutting head rotation

12

Before you start

Preparing the fuel

Fuel

 Recommended mixture ratio; 50: 1 (2%) for ISO-L-EGD

Standard (ISO 13738), JASO FC,FD grade and shindaiwa rec-

ommended oil.

 Never use two-stroke oil intended for water-cooled engines,

motor-cycle engines.

 Do not mix directly in engine fuel tank.

Fuel supply

 Do not add so much fuel that it reaches the mouth of the fuel

tank (A). Keep the fuel within the prescribed level (up to the

shoulder level (B) of the fuel tank).

 Tighten the fuel tank cap securely after refuelling.

DANGER

 Do not fuel up while the engine is hot or in operation.

 Do not smoke or hold a flame near when refuelling.

If you do so, the fuel could ignite and cause fire, leading to burns.

WARNING

 Do not fill fuel tanks indoors. Always fill fuel tanks outdoors over bare ground. Do not refuel the product on the load-

ing platform of a truck, or in other such places.

 Fuel tanks/cans may be under pressure. Always loosen fuel caps slowly allowing pressure to equalize.

Otherwise, fuel may get spewed.

 Mop up any fuel that overflows or spills out due to overfilling.

Fuel spills can cause fire and burns when ignited.

 After refuelling, always check that there are no leaks or discharges of fuel from the fuel pipe, fuel system grommets,

or around the fuel tank cap. If you do find fuel leaks or discharges, stop using the product immediately and contact

your dealer to have it repaired.

Any fuel leaks could cause fire.

 Keep the refuelling tank in a shaded area away from fire.

 Use an approved fuel container.

IMPORTANT

 Fuel is a mixture of regular grade petrol and an air-cooled 2-stroke engine oil. Minimum 89 Octane unleaded petrol is recom-

mended. Do not use fuel containing methyl alcohol or more than 10 % of ethyl alcohol.

 Stored fuel ages. Do not mix more fuel than you expect to use in thirty (30) days.

13

Engine operation

Starting the engine

Starting a cold engine

(Connect the spark plug cap if the product has been in storage for

a long period of time.)

1. Remove the blade cover.

2. Placing the product on level ground, check to ensure that the

cutting attachment does not come into contact with the sur-

face of the ground or any other impediment using a beam or

other such implement.

3. Move the ignition switch (A) to the Start position.

4. Make sure that the throttle trigger (D) is at the idle speed po-

sition.

WARNING

Be particularly careful to observe the following precautions when starting the engine:

 Move at least 3m from the place where you refuelled.

 Place the product in a flat, well ventilated place.

 Check that there are no fuel leaks.

 Inspect metal blades for cracks.

 Check that none of the nuts and bolts are loose.

 Leave plenty of space around the product and do not allow people or animals near it.

 Start the engine with the throttle trigger in the idle speed position.

 Hold the product firmly to the ground when starting the engine.

Failure to observe the precautions could cause an accident or injury, or even lead to a fatality.

 Check that there are no abnormal vibrations or sounds once the engine starts. Do not use the product if there are

abnormal vibrations or sounds. Contact your dealer to have it repaired.

Accidents involving parts that fall or shatter off can cause wounds or serious injury.

 The exhaust fumes from the engine contain toxic gases. Do not operate the product indoors or in other

ill ventilated places.

The exhaust fumes could cause poisoning.

 Do not touch silencer, spark plug, angle transmission, and other high temperature components while

the product is running or for some time after it stops.

You could burn yourself if you touch a high temperature component.

 Do not touch spark plug, spark plug wire, and other high voltage components while the product is run-

ning.

You could receive an electric shock if you touch a high voltage component while the product is running.

 If the cutting attachment rotates even though the throttle trigger is in the idle speed position when the engine is start-

ed, adjust the carburettor before using the product.

Failure to observe the precautions could cause an accident or injury, or even lead to a fatality.

 When starting engine using throttle latch, cutting attachment rotates. After engine starts, pull throttle trigger slightly

to release throttle latch immediately. Never use throttle latch for operation.

The rotating blade can cause injury.

NOTE

 Pull out the starter grip gently at first, and then more rapidly. Do not pull the starter rope out to more than 2/3 of its length.

 Do not let go of the starter grip as it returns.

14

Engine operation

5. Move the choke lever (F) to the "Cold Start" (E) position.

6. Alternately press and release the purge bulb (H) until the fuel

is sucked up into it.

7. Checking that the area around you is safe, hold the position

closest to the engine firmly as shown in the illustration, pull-

ing several times on the starter grip (I).

8. If you hear an explosion-like sound and the engine stops im-

mediately, move the choke lever to the "Run" (G) position

and continue pulling on the starter grip to start the engine.

9. If the engine does not stop, return the choke lever gently to

the "Run" position.

10. Leave the engine to warm up at idle speed for a while.

 When engine is hard to start, use throttle latch (C). (Pull throt-

tle trigger fully and lower throttle latch while pressing throttle

trigger lockout (B) and release throttle trigger to activate throt-

tle latch. After engine starts, pull throttle trigger slightly to re-

lease throttle latch immediately.)

Starting a warm engine

1. Move the ignition switch (A) to the Start position.

2. Make sure that the throttle trigger (D) is at the idle speed po-

sition.

3. Check that the choke lever is in the "Run" position.

4. If no fuel is visible in the purge bulb, alternately press and re-

lease the purge bulb until the fuel is sucked up into it.

5. Checking that the area around you is safe, hold the position

closest to the engine firmly, and pull on the starter grip to

start the engine.

Stopping the engine

1. Move the throttle trigger (B) to the idle speed position and set

the engine to idling (i.e. low speed).

2. Move the ignition switch (A) to the Stop position.

3. In the event of an emergency, stop the engine immediately

using the ignition switch.

4. If the engine fails to stop, move the choke lever to the "Cold

Start" position. The engine will stall and come to a halt (an

emergency stop).

 If the engine fails to stop when the ignition switch is used, have

the ignition switch checked and repaired by your dealer before

you use the product again.

5. Always disconnect the spark plug wire from the spark plug to

ensure the engine cannot be started before you work on the

unit or leave it unattended.

15

Trimming operation

DANGER

 Always stop the engine when a cutting attachment jam occurs.

Severe injury can occur if a jam is removed and the cutting attachment suddenly starts.

 Do not operate the product without the shield in place.

Any objects that ricochet off the cutting attachment could cause an accident or serious injury.

 The area within a 15 m radius of the product is a danger zone. Be care-

ful to observe the following precautions while working with the prod-

uct.

 Do not allow children and other people or pets to enter the danger

zone.

 If another person enters the danger zone, turn off the engine to stop

the cutting attachment from rotating.

 When approaching the operator, signal to him by, for example,

throwing twigs from outside the danger zone, and then check that

engine has been switched off and the cutting attachment has

stopped turning.

 If more than one person is working with the product, identify the way

in which you will signal to each other and work at least 15 m apart.

Any objects that ricochet off the cutting attachment, and any contact with the cutting attachment, could cause blindness or a

fatal accident.

WARNING

 Before starting work, check the area where you will be working and remove any small stones

and empty cans likely to ricochet off the cutting attachment, as well as any pieces of string

or wire that might become twisted around the cutting attachment.

An accident or serious injury can occur if foreign objects ricochet off the cutting attachment or wire

and other materials twisted round the product spring off it.

 In the following situations, turn off the engine immediately and ensure that the cutting attachments have stopped

before checking each area of the product. Replace any damaged parts.

 If the cutting attachment hits a rock, tree, post, or other such obstruction while you work.

 If the product suddenly starts to vibrate abnormally.

Continuing to use parts when they are damaged could lead to an accident or serious injury.

 Do not hold the cutting attachment up while you work. You must not work with the cutting attachments raised above

knee level.

Raising the cutting attachment above knee level brings the plane of rotation closer to the face, and any objects that fly off the

cutting attachments could cause an accident or serious injury.

Transport of the product

 When transporting in the situations described below, turn off the engine and ensure that the trimmer blade has

stopped rotating, then fit the trimmer blade cover and position the silencer away from yourself.

 Moving to the place where you are working.

 Moving to another area while you are working.

 Leaving the place where you have been working.

Failure to observe these precautions could cause burns or serious injury.

 When transporting the product by car, empty the fuel tank, fit the blade cover, and secure the product firmly in place

to prevent it from moving around.

Travelling by car with fuel in the fuel tank could lead to a fire.

 Never attempt to operate the product with one hand.

 Ensure that you hook your thumbs around the grips, wrapping them in your

thumb and remaining fingers.

16

Trimming operation

Using shoulder harness

Always mount the trimmer correctly using the shoulder har-

ness.

 Buckle waist belt. Belt should be snug.

 Attach product to harness.

 Loop handle version

Place shoulder harness over left shoulder and adjust

straps so the quick release pin rests just below the waist.

 U-handle version

Place shoulder harness over both shoulders and adjust

straps so the connecting point latches as shown.

 Check for correct adjustment by moving cutting attachment

along ground.

 Re-adjust position of suspension point if necessary.

 The shoulder harness is fitted with an emergency release

function.

 Loop handle version: In the event of a fire or other emer-

gency, pull the quick release pin (A) up to release the

product from your body.

 U-handle version: In the event of a fire or other emergen-

cy, pull the emergency tab (B) up to release the product

from your body.

Basic trimming operation with nylon line cutting head

Adjusting nylon line

 Do not rotate the nylon line cutting head at more than 10000 r/

min.

 When releasing nylon line from spool, hit tap knob of spool

against the ground surface lightly at rotation speed lower than

4500 r/min.

 Cut off knife on the shield adjusts cutting swath automatically

by cutting nylon lines evenly when attachment starts rotating.

 When operating with less than maximum cutting swath, cut

two nylon lines in equal lengths.

 When nylon line becomes shortened, hit tap knob (A) of spool

against the ground surface lightly and the line is released from

spool to come out.

Trimming

 This is feeding the trimmer carefully into the material you wish

to cut. Tilt the head slightly to direct the debris away from you.

If cutting up to a barrier such as a fence, wall or tree, approach

from an angle where any debris ricocheting off the barrier will

fly away from you.

 Move the nylon line cutting head slowly until the grass is cut

right up to the barrier, but do not jam (overfeed) the line into

the barrier. If trimming up wire mesh or chain link fencing, be

careful to feed only up to the wire. If you go too far, the line will

snap off around the wire.

 Trimming can be done to cut through weed stems one at a

time. Place the nylon line cutting head near the bottom of the

weed never high up, which could cause the weed to chatter

and catch the line. Rather than cut the weed right through, just

use the very end of the line to wear through the stem slowly.

1. Angle to wall

WARNING

 Serious injury may result from the improper use of cutting attachment. Read and comply with all safety instructions

listed in this manual.

 Use only cutting attachments recommended by YAMABIKO Corporation.

 Excessive nylon line beyond cut off knife could fly off when the nylon line cutting head starts rotating after adjust-

ment of nylon line length.

Failure to do so could lead to an accident or serious injury.

17

Trimming operation

2. Debris

3. Knife side raised

4. Angle to ground

Scything

 This is the cutting or mowing of large grassy areas by sweep-

ing or swinging the trimmer in a level arc. Use a smooth, easy

motion. Do not try to hack or chop down the grass. Tilt the ny-

lon line cutting head to direct the debris away from you on the

scything stroke. Then return without cutting grass for another

stroke. If you are well protected and do not care whether some

debris is thrown in your direction, you may scythe in both di-

rections.

Scalping and edging

 Both of these are done with the nylon line cutting head tilted at

a steep angle. Scalping (A) is removing top growth, leaving the

earth bare. Edging (B) is trimming the grass back where it has

spread over a pavement or driveway. During both edging and

scalping, hold the unit at a steep angle in a position where the

debris, and any dislodged dirt and stone, will not come back

towards you even if it ricochets off the hard surface.

 Although the pictures show how to edge and scalp, every op-

erator must find for himself the angles which suit his body size

and cutting situation.

 For nearly all cutting, it is good to tilt the nylon line cutting head

so that contact is made on the part of line circle where the line

is moving away from you and the shield (See appropriate pic-

ture). This results in the debris being thrown away from you.

 Tilting the head to the wrong side will shoot the debris toward

you. If the nylon line cutting head is held flat to the ground so

that cutting occurs on the whole line circle, debris will be

thrown at you, drag will slow the engine, and you will use up a

lot of line.

 Nylon line cutting head rotates anticlockwise. The knife will be

on the left side of the shield.

1. Debris

2. Cut on this side

 Do not push the line into tough weeds, trees, or wire fences.

 Pushing the line into chicken wire, chain link fencing or thick

brush can result in snapped-off line ends being hurled back at

the operator. The proper way is to cut right up to a barrier, such

as any of those mentioned, but never run the line into or

through the obstruction. Do not cut closely to obstruction or

barrier.

 Avoid nylon line contact with broken wire fencing. Pieces of

wire broken off by the trimmer can be hurled at high speeds.

18

Trimming operation

Basic trimming operation with metal blade

Scything weeds

 This is cutting by swinging the cutting attachment in a level

arc. It can quickly clear areas of field grass and weeds. Scyth-

ing should not be used to cut large, tough weeds or woody

growths.

 If a sapling or shrub binds the cutting attachment, do not use

the cutting attachment as a lever to free the bind, because this

will cause cutting attachment failure.

 Instead, shut off the engine and push the sapling or shrub to

free the blades.

WARNING

 Please observe the following instructions when trimming.

 Check to ensure that the trimmer blade has been tightened securely in place.

 Replace the shield if it is damaged or cracked.

 Replace the trimmer blade nut when it becomes worn.

 Do not cut into the ground with the blade.

 Do not operate with a dull, bent, fractured or discoloured blade and worn or damaged nut.

 Do not run engine at full throttle without a load.

Failure to do so could lead to an accident or serious injury.

 Use only cutting attachments recommended by YAMABIKO Corporation. YAMABIKO Corporation will not be respon-

sible for the failure of cutting devices, attachments or accessories which have not been tested and approved by

YAMABIKO Corporation for use with this unit.

 The type of blade used must be matched to the type and size of material cut. An improper or dull blade can cause

serious personal injury. Blades must be sharp. Dull blades increase the chance of kick-out and injury to yourself and

bystanders.

 Plastic/Nylon Grass/Weed Blades may be used where ever the nylon line head is used. Do not use this blade for

heavy weeds or brush.

 The 3 cutter blade is designed especially to cut weeds and grass. To avoid injury due to kickback or blade fracture,

do not use the 3 cutter blade to cut brush or trees.

 8 Tooth Weed/Grass Blade is designed for grass, garden debris and thick weeds. Do not use this blade for brush

or heavy woody growth, 19 mm diameter or larger.

 22 Tooth Clearing Blade is designed for dense thickets and saplings up to 64 mm diameter.

 80 Tooth Brush Blade is designed for cutting brush and woody growth up to 13 mm diameter.

Damaged or shattered blades can cause accidents and serious injury.

Kickback

 The phenomenon that occurs if the trimmer blade comes into

contact with a tree, post, rock or other hard object while ro-

tating at high speed and reacts by recoiling powerfully and

instantaneously is known as kickback.

 Causing kickback can result in a loss of control over the

product and is highly dangerous.

 In particular, if the front-right quadrant of the trimmer blade

(B) strikes a shrub or other such object, the trimmer blade

will cause the product to recoil sharply backwards to the

right.

 To prevent kickback, do not trim from left to right. Be careful to ensure that the trimmer blade does not strike any

hard objects.

 When trimming, ensure that the object you are cutting meets the portion of the blade 1/3 in from the front edge on

the left-hand side (A).

Failure to do so could cause an injury or fatal accident.

La page charge ...

Shindaiwa C281TS Manuel utilisateur

Ce manuel convient également à

Shindaiwa C281TS Manuel utilisateur

dans d''autres langues

Documents connexes

Autres documents