KitchenAid KUIX535HPS Guide d'installation

Marque: KitchenAid

Modèle: KUIX535HPS

Catégorie: Barbecues

Taper: Guide d'installation

ICE MAKER INSTALLATION INSTRUCTIONS

INSTRUCTIONS D’INSTALLATION DE LA MACHINE À GLAÇONS

INSTRUCCIONES DE INSTALACIÓN DE LA FÁBRICA DE HIELO

W11246206A

ICE MAKER SAFETY

You can be killed or seriously injured if you don't immediately

You

can be killed or seriously injured if you don't

All safety messages will tell you what the potential hazard is, tell you how to reduce the chance of injury, and tell you what can

happen if the instructions are not followed.

Your safety and the safety of others are very important.

We have provided many important safety messages in this manual and on your appliance. Always read and obey all safety

messages.

This is the safety alert symbol.

This symbol alerts you to potential hazards that can kill or hurt you and others.

All safety messages will follow the safety alert symbol and either the word “DANGER” or “WARNING.”

These words mean:

follow instructions.

instructions.

DANGER

WARNING

TABLE OF CONTENTS / TABLE DES MATIÈRES / ÍNDICE

ICE MAKER SAFETY ..................................1

INSTALLATION INSTRUCTIONS ...............2

Unpack the Ice Maker ..............................2

Location Requirements ............................2

Electrical Requirements ...........................3

Water Supply Requirements ....................3

Vacation or Extended Time Without Use ..3

Connect Water Supply .............................4

Drain Pump Installation

(on some models) .....................................5

Drain Connection .....................................7

Door Panel and Hinge Removal ...............9

Custom Wood Panel Use .......................13

Auxiliary Grill Installation ........................16

Leveling ..................................................16

Deep Clean .............................................17

SÉCURITÉ DE LA MACHINE

À GLAÇONS ..............................................19

INSTRUCTIONS D’INSTALLATION .........20

Déballage de la machine à glaçons .......20

Exigences d’emplacement .....................20

Spécications électriques ......................21

Spécications de l’alimentation en eau ..21

Vacances ou longue période

d’inutilisation ..........................................21

Raccordement à la canalisation d’eau ..22

Installation de la pompe de vidange

(sur certains modèles) ............................23

Raccord au drain ....................................26

Démontage du panneau de porte

etdes charnières ....................................27

Utilisation du panneau en bois

personnalisé ...........................................31

Installation de la grille auxiliaire ..............34

Ajustement de l’aplomb .........................35

Nettoyage en profondeur .......................35

SEGURIDAD DE LA FÁBRICA

DE HIELO ..................................................37

INSTRUCCIONES DE INSTALACIÓN .....38

Cómo desempacar la fábrica de hielo ...38

Requisitos de ubicación .........................38

Requisitos eléctricos ..............................39

Requisitos de suministro de agua .........39

Vacaciones o tiempo prolongado

sinuso ....................................................39

Conexión del suministro de agua ..........40

Instalación de la bomba de desagüe

(en algunos modelos) .............................41

Conexión de desagüe ............................44

Cómo quitar los paneles de

las puertas y las bisagras .......................45

Uso del panel de madera

personalizado .........................................49

Instalación de la rejilla auxiliar ................52

Nivelación ...............................................53

Limpieza intensa ....................................53

INSTALLATION INSTRUCTIONS

Unpack the Ice Maker

Removing Packaging Materials

Remove tape and glue from your ice maker before using.

■ To remove any remaining tape or glue from the exterior of the

ice maker, rub the area briskly with your thumb. Tape or glue

residue can also be easily removed by rubbing a small

amount of liquid dish soap over the adhesive with your

ngers. Wipe with warm water and dry.

■ Do not use sharp instruments, rubbing alcohol, ammable

uids, or abrasive cleaners to remove tape or glue. Do not

use chlorine bleach on the stainless steel surfaces of the ice

maker. These products can damage the surface of your ice

maker.

Cleaning Before Use

After you remove all of the packaging materials, clean the inside

of your ice maker before using it. See the cleaning instructions in

the “Ice Maker Care” section.

Location Requirements

■ To ensure proper ventilation for your ice maker, the front

side must be completely unobstructed. The ice maker may

be closed-in on the top and three sides, but the installation

should allow the ice maker to be pulled forward for servicing if

necessary.

■ The auxiliary grill kit provided (only on custom panel models)

can be used to align the toe grill with the rest of the cabinets

while not obstructing ventilation of the ice maker.

■ Installation of the ice maker requires a cold water supply inlet

of 1/4" (6.35 mm) OD soft copper tubing with a shutoff valve

or a Whirlpool supply line Part Number 8212547RB, and a

Whirlpool approved drain pump, Part Number 1901A, only to

carry the water to an existing drain.

■ Choose a well-ventilated area with temperatures above 55°F

(13°C) and below 110°F (43°C). Best results are obtained

between 70°F and 90°F (21ºC and 32°C).

■ The ice maker must be installed in an area sheltered from the

elements, such as wind, rain, water spray, or drip.

■ When installing the ice maker under a counter, follow the

recommended opening dimensions shown. Place electrical

and plumbing xtures in the recommended location as shown.

NOTES:

■ Check that the power supply cord is not damaged or

pinched or kinked between the ice maker and the cabinet.

■ Check that the water supply line is not damaged or

pinched or kinked between the ice maker and the cabinet.

■ Check that the drain line (on some models) is not

damaged or pinched or kinked between the ice maker and

the cabinet.

IMPORTANT SAFETY INSTRUCTIONS

WARNING

To reduce the risk of ﬁre, electric shock, or injury when using your ice maker, follow these basic

precautions

SAVE THESE INSTRUCTIONS

Plug into a grounded 3 prong outlet.

Do not remove ground prong.

Do not use an adapter.

Do not use an extension cord.

Disconnect power before manually cleaning the inside components.

Disconnect power before servicing.

Replace all parts and panels before operating.

Use two or more people to move and install ice maker.

WARNING

Excessive Weight Hazard

Use two or more people to move and install ice maker.

Failure to do so can result in back or other injury.

■ Choose a location where the oor is even. It is important for

the ice maker to be level in order to work properly. If needed,

you can adjust the height of the ice maker by changing the

height of the leveling legs. See “Leveling.”

Electrical Requirements

Before you move your ice maker into its nal location, it is

important to make sure you have the proper electrical connection:

A 115 V, 60 Hz., AC only, 15 or 20 A electrical supply, properly

grounded in accordance with the National Electrical Code and

local codes and ordinances, is required.

It is recommended that a separate circuit, serving only your ice

maker, be provided. Use a receptacle which cannot be turned off

by a switch or pull chain.

IMPORTANT: If this product is connected to a GFCI (Ground

Fault Circuit Interrupter) equipped outlet, nuisance tripping of the

power supply may occur, resulting in loss of cooling. Ice quality

may be affected. If nuisance tripping has occurred, and if the

condition of the ice appears poor, dispose of it.

Recommended Grounding Method

The ice maker must be grounded. The ice maker is equipped with

a power supply cord having a 3 prong grounding plug. The cord

must be plugged into a mating, 3 prong, grounding-type wall

receptacle, grounded in accordance with the National Electrical

Code and local codes and ordinances. If a mating wall receptacle

is not available, it is the personal responsibility of the customer to

have a properly grounded, 3 prong wall receptacle installed by a

qualied electrician.

Water Supply Requirements

Check that the water supply lines are insulated against freezing

conditions. Ice formations in the supply lines can increase water

pressure and damage your ice maker or home. Damage from

frozen supply lines is not covered by the warranty.

A cold water supply with water pressure of between 30 and

120 psi (207 and 827 kPa) is required to operate the ice maker.

If you have questions about your water pressure, call a licensed,

qualied plumber.

Reverse Osmosis Water Supply

IMPORTANT:

■ A reverse osmosis water ltration system is not recommended

for ice makers that have a drain pump installed.

■ For gravity drain systems only.

■ The pressure of the water supply coming out of a reverse

osmosis system going to the water inlet valve of the ice maker

needs to be between 30 and 120 psi (207 and 827 kPa).

If a reverse osmosis water ltration system is connected to your

cold water supply, the water pressure to the reverse osmosis

system needs to be a minimum of 40 to 60 psi (276 to 414 kPa).

NOTE: The reverse osmosis system must provide 1 gal. (3.8 L) of

water per hour to the ice maker for proper ice maker operation. If

a reverse osmosis system is desired, only a whole-house capacity

reverse osmosis system, capable of maintaining the steady

water supply required by the ice maker, is recommended. Faucet

capacity reverse osmosis systems are not able to maintain the

steady water supply required by the ice maker.

If the water pressure to the reverse osmosis system is less than

40 to 60 psi (276 to 414 kPa):

■ Check to see whether the sediment lter in the reverse

osmosis system is blocked. Replace the lter if necessary.

■ Allow the storage tank on the reverse osmosis system to rell

after heavy usage.

If you have questions about your water pressure, call a licensed,

qualied plumber.

Vacation or Extended Time Without Use

■ When you will not be using the ice maker for an extended

period of time, turn off the water and power supply to the ice

maker.

■ Check that the water supply lines are insulated against

freezing conditions. Ice formations in the supply lines can

increase water pressure and cause damage to your ice

maker or home. Damage from freezing is not covered by the

warranty.

A. Recommended location for electrical and plumbing xtures

B. Floor level

Electrical Shock Hazard

Plug into a grounded 3 prong outlet.

Do not remove ground prong.

Do not use an adapter.

Do not use an extension cord.

Failure to follow these instructions can result in death,

fire, or electrical shock.

WARNING

34"

(86.4 cm)

Min.

34¹⁄

(87.6 cm)

Max.

24"

(60.96 cm)

28¹⁄

(72.4 cm)

3¹⁄

(8.9 cm)

11¹⁄

(29.2 cm)

(22.9 cm)

Connect Water Supply

Read all directions before you begin.

IMPORTANT:

■ Plumbing shall be installed in accordance with the

International Plumbing Code and any local codes and

ordinances.

■ Use copper tubing or Whirlpool supply line, Part Number

8212547RP, and check for leaks.

■ Install tubing only in areas where temperatures will remain

above freezing.

Tools Needed

Gather the required tools and parts before starting installation:

■ Flat-blade screwdriver

■ 7/16" and 1/2" open-end wrenches or two adjustable

wrenches

■ 1/4" nut driver

NOTE: Do not use a piercing-type or 3/16" (4.76 mm) saddle

valve which reduces water ow and clogs more easily.

Connecting the Water Line

1. Turn off main water supply. Turn on nearest faucet long

enough to clear line of water.

2. Using a 1/2" copper supply line with a quarter-turn shutoff

valve or the equivalent, connect the ice maker as shown.

NOTE: To allow sufcient water ow to the ice maker a

minimum 1/2" diameter home supply line is recommended.

3. Now you are ready to connect the copper tubing. Use 1/4"

(6.35 mm) O.D. soft copper tubing for the cold water supply.

■ Ensure that you have the proper length needed for the job.

Be sure both ends of the copper tubing are cut square.

■ Slip compression sleeve and compression nut on copper

tubing as shown. Insert end of tubing into outlet end

squarely as far as it will go. Screw compression nut onto

outlet end with adjustable wrench. Do not overtighten.

4. Place the free end of the tubing into a container or sink, and

turn on main water supply and ush out tubing until water is

clear. Turn off shutoff valve on the water pipe.

IMPORTANT: Always drain the water line before making

the nal connection to the inlet of the water valve to avoid

possible water valve malfunction.

5. Water inlet tube is located on the rear side of the ice maker as

shown in "Rear View" illustration. Bend the copper tubing to

match with water line inlet. Leave the coil of copper tubing as

it is to allow the ice maker to be pulled out of the cabinet or

away from the wall for service.

Rear View

6. Remove and discard the short, plastic tube from the end of

the water line inlet.

7. Thread the nut onto the end of the tubing. Tighten the nut by

hand. Then tighten it with a wrench two more turns. Do not

overtighten.

NOTE: To avoid rattling, be sure the copper tubing does not

touch the cabinet’s side wall or other parts inside the cabinet.

A. Bulb

B. Nut

A. Compression sleeve

B. Compression nut

C. Copper tubing

A. Copper tubing

B. Water supply tube clamp

C. Inlet water tube clamp and

supply line connector

DAB C

A. Line to ice maker

B. Nut (purchased)

C. Ferrule (purchased)

D. Supplied line from ice maker

8. Install the water supply tube clamp around the water supply

line to reduce strain on the coupling.

9. Turn shutoff valve ON.

10. Check for leaks. Tighten any connections (including

connections at the valve) or nuts that leak.

Drain Pump Installation

(on some models)

NOTES:

■ Connect drain pump to your drain in accordance with all state

and local codes and ordinances.

■ It may be desirable to insulate drain tube thoroughly up

to drain inlet to minimize condensation on the drain tube.

Insulated tube kit Part Number W10365792 is available for

purchase.

■ Drain pump is designed to pump water to a maximum height

of 10 ft (3 m). Use only Whirlpool approved drain pump kit

Part Number 1901A.

■ Do not connect the outlet end of the drain tube to a closed

pipe system to keep drain water from backing up into the ice

maker.

Kit Contains:

■ Drain pump kit Part Number 1901A

■ 5/8" I.D. x 5

" drain tube (ice maker bin to drain pump

reservoir inlet)

■ 1/2" I.D. x 10 ft (3 m) drain tube hose (drain pump discharge

to household drain)

■ 5/16" I.D. x 32" (81 cm) vent tube (drain pump reservoir vent

to ice maker cabinet back)

■ Cable tie (secures vent tube to back of ice maker) (1)

■ #8-32 x 3/8" pump mounting screws (secures drain pump to

baseplate and clamps to back of ice maker) (5)

■ 5/8" small adjustable hose clamp (secures vent to drain

pump)

■ 7/8" large adjustable hose clamp, (secures drain tube to ice

maker bin and drain pump reservoir inlet) (3)

■ Rear panel (2)

■ Instruction sheet

If Ice Maker Is Currently Installed

NOTE: If ice maker is not installed, please proceed to “Drain

Pump Installation” section.

1. Push the selector switch to the OFF position.

2. Unplug ice maker or disconnect power.

3. Turn off water supply. Wait 5 to 10 minutes for the ice to fall

into the storage bin. Remove all ice from bin.

4. Unscrew the drain cap from the bottom of the water

pan located inside the storage bin. Allow water to drain

completely. Replace drain cap. See “Drain Cap” illustration.

Drain Cap

5. If ice maker is built into cabinets, pull ice maker out of the

opening.

6. Disconnect water supply line. See “Water Supply Line”

illustration.

Water Supply Line

Drain Pump Installation

NOTE: Do not kink, smash or damage tubes or wires during

installation.

1. Unplug ice maker or disconnect power.

2. Remove rear panel. See “Rear Panel” illustration for 5 screw

locations. Pull rear panel away from the drain tube and

discard.

Rear Panel

WARNING

Electrical Shock Hazard

Disconnect power before servicing.

Replace all parts and panels before operating.

Failure to do so can result in death or electrical shock.

A. Drain cap

A. 1/4" copper tubing

B. Cable clamp

C. 1/4" compression nut

D. Ferrule (sleeve)

E. Ice maker connection

A. Screw locations

3. Remove the old drain tube and clamp attached to the ice

maker bin.

NOTE: Discard old drain tube and clamp.

4. Install new drain tube (5/8" I.D. x 5¹⁄

") from ice maker bin to

drain pump reservoir inlet using new adjustable clamps. See

“Drain Tube” illustration.

NOTES:

■ Do not kink.

■ Trim tube length if required.

Drain Tube

5. Install vent tube (5/16" I.D. x 32" [81 cm]) to drain pump

reservoir vent. Use supplied 5/8" small adjustable clamps.

See “Parts Locations” illustration. Use plastic retainer to keep

vent hose secure to top of inner deck.

NOTE: Do not install household drain tube at this time.

Parts Locations

6. Remove power cord clamp and ground screw attached to ice

maker power cord, which is mounted to the unit base. See

“Parts Locations” illustration.

NOTE: Clamp and screw will be reused.

7. Slide drain pump into the ice maker base on the right side.

The pump mounting tab should slip into the rectangular slot

in the ice maker base. It will be necessary to tip the pump

slightly to slip into the slot. See “Drain Pump Mounting Tab

Slot” illustration.

Drain Pump Mounting Tab Slot

Drain Pump Installed

8. Align the 2 screw holes at the rear of the pump. Use two

#8-32 x 3/8" screws, supplied. See “Parts Locations”

illustration.

9. Connect drain tube to ice maker bin outlet (5/8" I.D.), using

7/8" adjustable clamp, supplied. See “Drain Tube” illustration.

10. Coil ice maker power cord into a 4" (10.2 cm) diameter

coil. Wrap electrical tape around the power cord in several

places to keep the cord in a coil. Locate coiled power cord

between the drain pump and side of enclosure and plug into

the receptacle of the drain pump. See “Parts Locations”

illustration.

11. Attach the drain pump power cord to ice maker unit base with

clamp and screw (removed in Step 6) that was used to attach

ice maker power cord. See “Parts Locations” illustration.

12. Place new rear panel (small one for 15" ice makers, large one

for 18") against the back of the ice maker. Route the vent tube

and drain pump discharge tube through cutouts in the rear

panel.

13. Secure rear panel with original screws. See “Rear Panel”

illustration.

A. 7/8" adjustable hose clamp

B. Drain tube (ice bin to drain pump)

C. 7/8" adjustable hose clamp

D. Drain pump reservoir inlet

A. Vent tube

B. 5/8" hose clamp

C. Drain pump discharge tube

D. Drain pump

E. Ice maker unit power cord

F. #8-32 x 3/8" pump mounting

screws

G. Drain pump power cord,

clamp and screw

H. Plastic retainer

I. Wiring cover

A. Mounting tab slot

A. Drain pump installed

14. Remove wiring cover. Refer following illustration for location of

the screws.

15. Route vent tube through plastic retainer that is located

underneath top deck in open pump area as shown in

illustration. Using cable tie, tie the vent tube to the black

suction tube which is located behind the wiring cover. Refer

"Vent Tube" illustration.

16. Secure wiring cover back in place.

17. Attach 1/2" I.D. x 10 ft (3 m) drain tube to pump discharge

tube. See “Parts Locations” illustration.

NOTE: Do not connect outlet end of drain tube to a closed

pipe system to keep drain water from backing up into the ice

maker

18. Connect ice maker to water supply and install ice maker as

specied by the product installation instructions

Vent Tube

NOTE: Do not pinch, kink or damage the vent tube. Check that it

is not damaged or pinched or kinked between the cabinet and the

ice maker.

19. Check all connections for leaks.

20. Plug in ice maker or reconnect power.

21. Turn on ice maker.

22. Wait for rinsing cycle, approximately 5 minutes, to be sure the

ice maker is operating properly.

Drain Connection

Gravity Drain System

Connect the ice maker drain to your drain in accordance with all

state and local codes and ordinances. If the ice maker is provided

with a gravity drain system, follow these guidelines when

installing drain lines. This will help keep water from owing back

into the ice maker storage bin and potentially owing onto the

oor, causing water damage.

■ Drain lines must have a minimum of 5/8" (15.88 mm) I.D.

(inside diameter).

■ Drain lines must have a 1" drop per 48" (2.54 cm drop per

122 cm) of run or 1/4" drop per 12" (6.35 mm per 30.48 cm) of

run and must not have low points where water can settle.

■ The oor drains must be large enough to accommodate

drainage from all drains.

■ The ideal installation has a standpipe with a 1¹⁄

" (3.81 cm) to

2" (5.08 cm) PVC drain reducer installed directly below the

outlet of the drain tube as shown. You must maintain a 1"

(2.54 cm) air gap between the drain hose and the standpipe.

■ Do not connect the outlet end of the drain tube to a closed

pipe system to keep drain water from backing up into the ice

maker.

IMPORTANT: A drain pump is necessary when a oor drain is not

available. A Drain Pump kit, Part Number 1901A, is available for

purchase.

A. Wiring cover

B. Screws

A. Vent tube

B. Cable ties

C. Plastic retainer

Electrical Shock Hazard

Plug into a grounded 3 prong outlet.

Do not remove ground prong.

Do not use an adapter.

Do not use an extension cord.

Failure to follow these instructions can result in death,

fire, or electrical shock.

WARNING

Side View

Drain Pump System (on some models)

IMPORTANT:

■ Connect the ice maker drain to your drain in accordance with

the International Plumbing Code and any local codes and

ordinances.

■ The drain pump discharge line must terminate at an open

sited drain.

■ Maximum rise 10 ft (3.1 m)

■ Maximum run 100 ft (30.5 m)

NOTES:

■ If the drain hose becomes twisted and water cannot drain,

your ice maker will not work.

■ It may be desirable to insulate the drain line thoroughly

up to the drain inlet. An Insulation Sleeve kit, Part Number

W10365792, is available for purchase.

■ Do not connect the outlet end of the drain tube to a closed

pipe system to keep drain water from backing up into the ice

maker.

■ Drain pump maximum capability: For every 1 ft (0.31 m) of

rise, subtract 10 ft (3.1 m) of maximum allowable run.

Connecting the Drain

After ensuring that the drain system is adequate, follow these

steps to properly place the ice maker:

1. Plug into a grounded 3 prong outlet.

2. Style 1— For gravity drain system, push the ice maker into

position so that the ice maker drain tube is positioned over

the PVC drain reducer. See “Gravity Drain System.”

Style 2— For drain pump system connect the drain pump

outlet hose to the drain. See “Drain Pump System.”

3. Recheck the ice maker to be sure that it is level. See

“Leveling.”

4. If it is required by your local sanitation code, seal the cabinet

to the oor with an approved caulking compound after all

water and electrical connections have been made.

A. Drain hose

B. 1" (2.54 cm) air gap

C. PVC drain reducer

D. Center of drain should be 23" (58.4 cm) from

front of door, with or without the 3/4" (1.91

cm) panel on the door. The drain should also

be centered from left to right (7

" [18.56 cm]

from either side of the ice maker).

Electrical Shock Hazard

Plug into a grounded 3 prong outlet.

Do not remove ground prong.

Do not use an adapter.

Do not use an extension cord.

Failure to follow these instructions can result in death,

fire, or electrical shock.

WARNING

Excessive Weight Hazard

Use two or more people to move and install ice maker.

Failure to do so can result in back or other injury.

(4.8 cm)

2" - 1

(5 cm - 3.8 cm)

23"

(58.4 cm)

1" (2.54 cm)

Door Panel and Hinge Removal

1. Unplug the ice maker or disconnect power.

2. Remove the hinge cover from the upper and lower hinges.

3. To remove, cut hinge cover at indicated point using diagonal

cutting plier and remove from around hinges.

NOTE: Reinstall the hinge covers if product is removed from

cabinet installation.

4. Remove the plastic screw cover from the inside of the hinges

and set aside.

5. Remove the top and bottom plastic end caps from the door.

6. Unscrew the door hinge screws completely. Remove hinge pin

from top hinge and set aside.

7. Loosen the cabinet Phillips head screws halfway, so that the

hinge can slide off.

WARNING

Electrical Shock Hazard

Disconnect power before servicing.

Replace all parts and panels before operating.

Failure to do so can result in death or electrical shock.

Crush Hazard

Articulated hinges are self closing and many pinch

points exist prior to cabinet installation.

Do not remove hinge covers until product is ready to

be installed.

Failure to follow these instructions can result in crush,

cut, or pinch injuries.

WARNING

8. Repeat steps 6 and 7 on the second hinge.

NOTE: Keep track of where each door hinge was originally

located, at the top or bottom of the unit.

Preparing the Bottom Hinges

1. Once both hinges are removed, unscrew the grill cover by

using a TORX T20

†

screwdriver.

NOTE: The door may fall open. This is normal.

2. Remove the black screw cover from the grill by opening the

grill cover, pushing the screw cap inwards, and sliding it out to

the side. Remove the hinge shim.

3. To attach the black screw cover to the opposite side, rst pull

the grill cover out.

4. Place the black screw cover between the grill and the screws.

Install the hinge shim on the opposite side, making sure the

notches face down and out.

NOTE: Make sure all of the covers's edges are behind the lip

of the grill, or it will not stay in place.

5. Once the cover is secure, push the grill cover back into its

original position, and replace the grill screws.

Reversing the Hinges

1. Place the hinge shim on the opposite side of the ice maker.

NOTE: The hinge shim is notched on the bottom-inner side to

indicate proper placement. Flip the hinge shims as needed to

make sure that the notches are facing in and down.

Black screw cover

Hinge shim

†TORX and T20 are trademarks of Acument Intellectual Properties, LLC.

2. Take the original upper hinge, ip it 180 degrees, and place it

in the lower hinge position on the opposite side, resting on the

cabinet hinge screws (i.e. the upper right hinge is now the

lower left hinge).

NOTE: The extensions on the hinges should always face

inside, not outside.

3. Take the original lower hinge, ip it 180 degrees, and place it

in the upper hinge position on the opposite side resting on the

cabinet hinge screws.

4. Both hinges should be resting on the cabinet hinge screws.

Make sure that all screws are fully tightened. Take hinge pin

and place it in the new top hinge (originally at bottom hinge).

5. Place screw cap covers on all open screw holes. Screw cap

covers must also be placed at the original locations of the

hinges.

Reversing the Side Caps

1. Place the door on a at surface, steel side up.

2. Unscrew TORX

†

screws on non-hinged side.

3. Take the original upper end cap, ip it 180 degrees, and place

it on the lower hinge position on the non-hinged side (i.e. the

upper right end cap is now the lower left end cap).

NOTE: If using a custom panel door, side caps can only be

slid out from the installation bracket horizontally.

4. Take the original lower side end cap, ip it 180 degrees, and

place it on the upper hinge position on the non-hinged side.

NOTE: The end caps should be on the opposite corner on

which they started, and opposite sides on the hinges.

5. See the graphic below to verify completed end cap reversal

on your appliance.

Final Door Placement

NOTE: Before placing the door back on the ice maker, check all

installed parts to ensure there are no exposed screws, all screw

cover caps are on, and the door is facing the correct way with the

stainless steel door facing out.

1. Slide the door panel behind the hinges. The screws will go in

through the hinge rst, and then the door panel.

2. Place the steel door panel back on the door once all screws

are tightened.

3. Screw the two hex heads screws back in at the bottom of the

door.

Reverse Door Catch

1. Remove the white decorative screws from the opposite side

of the door and set aside.

2. Remove the screws from the magnetic door catch and place

them on the opposite side of the door.

3. Install the white decorative screws on the opposite side of the

door.

4. Plug into a grounded 3 prong outlet.

Custom Wood Panel Use

Custom Panel Dimensions

If you plan to install a custom overlay panel, you will need to

make the panel yourself or consult qualied cabinetmaker or

carpenter

IMPORTANT:

■ The thickness of overlay panel must be 3/4" (1.91 cm).

■ Overlay panel must not weigh more than 8lbs (3.62 kg).

■ Overlay panels weighing more than recommended may cause

damage to your ice maker.

■ Match wood grain direction with that of adjacent cabinets.

■ Sand panel edges to provide a smooth nish.

■ Use moisture sealer on both sides and all edges of the panel

to avoid damage from outside.

Option 1 - Without Hinge-Side Spacer

To allow proper clearance for the door, prepare the custom

overlay panel using the dimension shown.

Electrical Shock Hazard

Plug into a grounded 3 prong outlet.

Do not remove ground prong.

Do not use an adapter.

Do not use an extension cord.

Failure to follow these instructions can result in death,

fire, or electrical shock.

WARNING

14 ¹⁷⁄₃₂"

(36.9 cm)

29 ¹⁄₂"

(74.9 cm)

¹⁄₄

(3.18 cm)

¹⁄₄

(3.18 cm)

¹⁄₄"

(6.35 mm)

¹⁄₄"

(6.35 mm)

³⁄₄"

(1.91 mm)

³⁄₄"

(1.91 mm)

Option 2 - With Hinge-Side Spacer

To achieve a ush installation with adjacent cabinets, prepare the

custom overlay panel using the dimensions shown.

Top of Panel

Bottom of Panel

Custom Panel Installation

1. From inside the door, install two wood screws through the

slotted holes in the top and bottom door brackets. Adjust the

panel side to side to achieve a 1/8" gap on both sides. Install

the remaining screws through the door bracket into the panel.

2. Replace the side caps into the door panel. Tighten all screws

to secure position.

Installation into cabinet

1. Remove the hinge cover from the upper and lower hinges.

2. To remove, cut hinge cover at indicated point using diagonal

cutting plier and remove from around hinges. Unscrew and

remove the side caps in the door by sliding them out.

NOTE: Reinstall the hinge covers if product is removed from

cabinet installation.

14 ⁵⁄₈"

(37.1 cm)

29 ¹⁄₂"

(74.9 cm)

A. Front-visible surface when installed

B. Hinge Side

A. Front-visible surface when installed

B. Hinge Side

Crush Hazard

Articulated hinges are self closing and many pinch

points exist prior to cabinet installation.

Do not remove hinge covers until product is ready to

be installed.

Failure to follow these instructions can result in crush,

cut, or pinch injuries.

WARNING

3. Plug into a grounded 3 prong outlet. Install ice maker into

cabinet.

4. Push any extra drain hose, water line, or power cord in the

slot in the back panel.

NOTE: Any time ice maker is removed for service, do the

same process when placing the unit back in the cabinets.

5. Secure the top and bottom hinges to the side of the cabinet

using wood screws.

6. Holes are provided on the non hinge side for cabinet brackets

installation. Attach cabinet brackets (provided with unit) to

front of ice maker as shown in the illustration. Attach the

cabinet brackets to the side of the cabinet with wood screws.

7. Lightly press the custom panel onto the door using double

sided adhesives. Adjust height of the panel to achieve a 1/8"

gap between top of door panel and counter sealing gap.

Press the panel rmly against door.

Electrical Shock Hazard

Plug into a grounded 3 prong outlet.

Do not remove ground prong.

Do not use an adapter.

Do not use an extension cord.

Failure to follow these instructions can result in death,

fire, or electrical shock.

WARNING

Cabinet bracket

Auxiliary Grill Installation

The auxiliary grill is an optional part that can be used to align

the toe grill with the rest of the cabinets (while not obstructing

ventilation of the ice maker).

Tools required:

■ TORX T20

†

screwdriver

■ 1/8" straight drill bit and power drill

1. First, complete all installation steps and install leveled ice

maker into the cabinet. Ensure ice maker is ush with the

adjacent cabinets.

2. Unpackage kit but removing outer cushion packaging and

discard packaging material.

3. Remove screws that are taped onto the inside of the auxiliary

grill.

4. Place grill onto cabinetry. Align part so that grating pattern on

the auxiliary grill matches that of the toe grill on the ice maker.

5. Center auxiliary grill on cut out for ice maker. Mark hole

locations on each side of auxiliary grill on cabinet.

6. Using power drill and a 1/8" drill bit, drill holes in cabinet. This

is to t screws of size 8-18 x 0.750.

7. Using the TORX T20

†

screwdriver, screw auxiliary grill into

cabinet.

NOTE: For future service of ice maker, auxiliary kit must be

removed prior to the removal of the ice maker from the cabinets.

Leveling

It is important for the ice maker to be level in order to work

properly. Depending upon where you install the ice maker, you

may need to make several adjustments to level it. You may also

use the leveling legs to lower the height of the ice maker for

undercounter installations.

Tools Needed

Gather the required tools and parts before starting installation.

■ Level

■ Adjustable wrench

NOTE: It is easier to adjust the leveling legs if you have another

person to assist you.

1. Move the ice maker to its nal location.

NOTE: If this is a built-in installation, move the ice maker as

close as possible to the nal location.

2. Place the level on top of the product to see whether the ice

maker is level from front to back and side to side.

3. Push up on the top front of the ice maker, and then locate the

leveling screws that are on the bottom front of the ice maker.

4. Using an adjustable wrench, change the height of the legs as

follows:

■ Turn the leveling leg to the right to lower that side of the

ice maker.

■ Turn the leveling leg to the left to raise that side of the ice

maker.

NOTE: The ice maker should not wobble. Use shims to add

stability when needed.

5. Push up on the top rear of the ice maker and locate the

leveling legs that are on the bottom rear of the ice maker.

6. Follow the instructions in Step 4 to change the height of the

legs.

7. Use the level to recheck the ice maker to see that it is even

from front to back and side to side. If the ice maker is not

level, repeat steps 2 to 5. If the ice maker is level, go to the

“Connect Water Supply” section.

Deep Clean

Interior Components

1. Unplug ice maker or disconnect power.

2. Open the storage bin door and remove any ice that is in the

bin.

3. Remove the drain cap from the water pan and drain

thoroughly. Replace the drain cap securely on the water pan.

If the drain cap is loose, water will empty from the water pan,

and you will have either thin ice or no ice.

4. Pull out on the bottom of the cutter grid cover until the snaps

release to remove.

NOTE: On some models, remove the screw from the cutter

grid cover.

5. Unplug the wiring harness from the left side of the cutter grid.

6. Unplug the ice level sensor from the right side of the cutter

grid. Pull the ice level sensor down and forward away from the

cutter grid.

7. Remove the right-hand and left-hand screws. Lift the cutter

grid up and out.

NOTE: Make sure the plastic spacer from the right-hand side

of the cutter grid bracket stays with the cutter grid.

8. Remove the mounting screw that holds the water pan in

place. Pull out on the front of the water pan.

9. Disconnect the pump bracket from the water pan and unplug

the water pan drain pump.

10. Remove, clean and replace the ice scoop holder and ice

scoop.

NOTE: On some models, the ice scoop holder is located in

the upper left of the unit, and on other models, the ice scoop

holder is located in the lower left of the unit.

On Some Models

■ Remove the holder by removing the 2 screws.

■ Wash the ice scoop holder and ice scoop along with the

other interior components using the following instructions.

■ Replace the ice scoop holder by replacing the screws.

On Some Models

■ After removing the ice scoop, remove the holder by

removing the 2 screws.

NOTE: On some models, remove the holder by lifting up

on the ice scoop holder and then out.

A. Cutter grid cover

B. Screw (on some models)

A. Cutter grid cover

A. Cutter grid harness

B. Screw

C. Cutter grid

D. Ice level sensor harness

E. Plastic spacer

F. Screw

A. Water pan

B. Water pan screw

C. Drain cap

D. Drain pump cover

A. Screw

B. Ice scoop holder

■ Wash the ice scoop holder along with the other interior

components using the following instructions.

■ Replace the ice scoop holder by replacing the screws or

on some models, pushing in on the holder and then down.

11. Wash the interior components (cutter grid, exterior of hoses,

and water pan) and the storage bin, door gasket, ice scoop,

and ice scoop holder with mild soap or detergent and warm

water. Rinse in clean water. Then clean the same parts with a

solution of 1 tbs (15 mL) of household bleach in 1 gal. (3.8 L)

warm water. Rinse again thoroughly in clean water.

NOTE: Do not remove hoses. Do not wash plastic parts in

dishwasher. They cannot withstand temperatures above

145°F (63°C).

12. To replace the water pan, set the water pan inside the ice bin.

Hook up the water pan pump. Snap the pump bracket back

onto the water pan and place back into position. Secure the

water pan by replacing the mounting screw.

13. Check the following:

■ Drain cap from the water pan is securely in place. If the

drain cap is loose, water will empty from the water pan,

and you will have either thin ice or no ice.

■ Hose from water pan is inserted into storage bin drain

opening.

14. Slide the cutter grid back into place and secure it by replacing

the right-hand screw and plastic spacer. Then tighten the left-

hand screw. Reconnect the cutter grid harness and the ice

level sensor harness.

15. Replace the cutter grid cover.

NOTE: On some models, replace the cutter grid cover using

the screw removed earlier.

16. Gently wipe the control panel with a soft, clean dishcloth

using warm water and a mild liquid dish detergent.

17. Plug in ice maker or reconnect power.

18. After cleaning, make sure that all controls are set properly and

that no control indicators are ashing.

Quick Clean

You will need to use one 16-ounce (473 mL) bottle of approved

ice maker cleaner. We recommend using the affresh

Ice Machine

Cleaner part number 4396808.

A. Ice scoop holder

SÉCURITÉ DE LA MACHINE À GLAÇONS

IMPORTANTES INSTRUCTIONS DE SÉCURITÉ

AVERTISSEMENT :

Pour réduire le risque d'incendie, de choc électrique ou de blessures lors de l'utilisation de la

machine à glaçons, il convient d'observer certaines précautions élémentaires :

CONSERVEZ CES INSTRUCTIONS

Brancher sur une prise à 3 alvéoles reliée à la terre.

Ne pas enlever la broche de liaison à la terre.

Ne pas utiliser un adaptateur.

Ne pas utiliser un câble de rallonge.

Débrancher la source de courant électrique avant de

nettoyer manuellement les composants intérieurs.

Déconnecter la source de courant électrique avant

l'entretien.

Replacer pièces et panneaux avant de faire la remise en

marche.

Utiliser deux personnes ou plus pour déplacer et

installer la machine à glaçons.

Risque possible de décès ou de blessure grave si vous ne

suivez pas immédiatement les instructions.

Risque possible de décès ou de blessure grave si vous

ne suivez pas les instructions.

Tous les messages de sécurité vous diront quel est le danger potentiel et vous disent comment réduire le risque de blessure et

ce qui peut se produire en cas de non-respect des instructions.

Votre sécurité et celle des autres est très importante.

Nous donnons de nombreux messages de sécurité importants dans ce manuel et sur votre appareil ménager. Assurez-vous de

toujours lire tous les messages de sécurité et de vous y conformer.

AVERTISSEMENT

DANGER

Voici le symbole d’alerte de sécurité.

Ce symbole d’alerte de sécurité vous signale les dangers potentiels de décès et de blessures graves à vous

et à d’autres.

Tous les messages de sécurité suivront le symbole d’alerte de sécurité et le mot “DANGER” ou

“AVERTISSEMENT”. Ces mots signifient :

INSTRUCTIONS D’INSTALLATION

Déballage de la machine à glaçons

Enlèvement des matériaux d’emballage

Enlever le ruban adhésif et la colle de la machine à glaçons avant

de l’utiliser.

■ Pour enlever tout résidu de ruban adhésif ou de colle de la

surface extérieure de la machine à glaçons, frotter vivement

la zone avec le pouce. Les résidus de ruban adhésif et de

colle peuvent aussi facilement être enlevés en frottant à l’aide

d’un doigt une petite quantité de savon liquide à vaisselle sur

l’adhésif. Rincer à l’eau tiède et sécher.

■ Ne pas utiliser d’instruments coupants, d’alcool à friction, de

liquides inammables ou de nettoyants abrasifs pour enlever

le ruban adhésif ou la colle. Ne pas utiliser d’eau de Javel sur

les surfaces en acier inoxydable de la machine à glaçons.

Cesproduits peuvent endommager la surface de votre

machine à glaçons.

Nettoyage avant utilisation

Après avoir enlevé tous les matériaux d’emballage, nettoyer

l’intérieur de la machine à glaçons avant de l’utiliser. Voir les

instructions de nettoyage dans la section “Entretien de la

machineà glaçons”.

Exigences d’emplacement

■ Pour assurer une bonne aération de votre appareil, l’avant

doit être complètement dégagé. Les autres côtés et le dessus

de l’appareil peuvent être dissimulés, mais l’installation doit

permettre de tirer la machine à glaçons vers l’avant pour y

faire l’entretien requis.

■ L’ensemble de grilles auxiliaires inclus (seulement sur les

modèles avec panneau personnalisé) peut être utilisé pour

aligner la grille inférieure avec le reste des armoires sans

bloquer la ventilation de la machine à glaçons.

■ L’installation de la machine à glaçons requiert un tuyau

d’alimentation en eau en cuivre de 1/4 po (6,35mm) de

diamètre extérieur avec robinet d’arrêt ou la canalisation

d’alimentation de Whirlpool (numéro de pièce: 8212547RB)

etune pompe de vidange approuvée par Whirlpool (numéro

de pièce: 1901A) pour diriger l’eau vers un drain existant.

■ Choisir un endroit bien aéré où la température est supérieure

à 13°C (55°F) et inférieure à 43°C (110°F). Les meilleurs

résultats sont obtenus lorsque la température est comprise

entre 21°C et 32°C (70°F et 90°F).

■ La machine à glaçons doit être installée dans un

endroit protégé des éléments comme le vent, la pluie,

leséclaboussures d’eau ou les renversements.

■ Lorsque l’appareil est installé sous un comptoir, observer

les dimensions d’ouverture recommandées. Positionner les

entrées électrique et d’eau aux emplacements recommandés.

REMARQUES:

■ Vérier que le cordon d’alimentation n’est pas

endommagé, déformé ou coincé entre la machine

àglaçons et la caisse de l’appareil.

■ Vérier que le tuyau d’entrée d’eau n’est pas endommagé,

déformé ou pincé entre la machine à glaçons et l’armoire.

■ Vérier que la canalisation d’évacuation (sur certains

modèles) n’est pas endommagée, déformée ou coincée

entre la machine à glaçons et la caisse de l’appareil.

AVERTISSEMENT

Risque du poids excessif

Utiliser deux ou plus de personnes pour déplacer et

installer la machine à glaçons.

Le non-respect de cette instruction peut causer

une blessure au dos ou d'autre blessure.

La page est en cours de chargement...

KitchenAid KUIX535HPS Guide d'installation

Marque: KitchenAid

Modèle: KUIX535HPS

Catégorie: Barbecues

Taper: Guide d'installation

Télécharger le PDF

rapport

dans d''autres langues

English: KitchenAid KUIX535HPS Installation guide
español: KitchenAid KUIX535HPS Guía de instalación

KitchenAid KUIX535HPS Guide d'installation

KitchenAid KUIX535HPS Guide d'installation

dans d''autres langues

Documents connexes

Autres documents