Jenn-Air JIM158XXRS1 Manuel utilisateur

Marque: Jenn-Air

Modèle: JIM158XXRS1

Taper: Manuel utilisateur

Ce manuel convient également à

JENN-AIR_ICEMAKER

F.A,BRICADEHIELOJENN-AIR_

MACHINE.A.GLA(_ONSJENN-AIRTM

USE& CAREGUIDE

For questions about features, operation/performance, parts, accessories, or service, call:

1-800-JENNAIR (1-800-536-6247) or visit our website at www.jennair.com.

In Canada, call: 1-800-807-6777, or visit our website at www.jennair.ca.

MANUAL DEUSOY CUIDADO

Si tiene preguntas respecto alas caracteristicas, funcionamiento, rendimiento, partes, accesorios o servicio tecnico, Ilame al:

1-800-JENNAIR (1-800-536-6247) o visite nuestro sitio de internet: www.jennair.com.

En CanadA, Ilame al: 1-800-807-6777, o visite nuestro sitio de internet: www.jennair.ca.

GUIDED'UTILISATIONETD'ENTRETIEN

Au Canada, pour assistance, installation ou service, composez le 1-800-807-6777 ou visitez notre site Web www.jennair.ca.

Table of Contents/[ndice/Table des matieres ...................................................................................... 2

_]ENN-AIR_

W10282143A

TABLEOF CONTENTS

ICE MAKER SAFETY ................................................................................... 3

INSTALLATION INSTRUCTIONS ............................................................... 3

Tools and Parts ......................................................................................... 3

Custom Panel Dimensions ....................................................................... 3

Unpack the Ice Maker ............................................................................... 5

Location Requirements ............................................................................. 5

Electrical Requirements ............................................................................ 6

Water Supply Requirements ..................................................................... 6

Leveling ..................................................................................................... 6

Connect Water Supply .............................................................................. 6

Drain Connection ...................................................................................... 7

Install Custom Overlay Panel .................................................................... 8

Ice Maker Door ......................................................................................... 9

Normal Sounds ....................................................................................... 10

ICE MAKER USE ....................................................................................... 11

How Your Ice Maker Works ................................................................... 11

Using the Controls .................................................................................. 11

ICE MAKER CARE ..................................................................................... 12

Cleaning .................................................................................................. 12

Vacation and Moving Care ..................................................................... 13

TROUBLESHOOTING ............................................................................... 14

Ice Maker Operation ............................................................................... 14

Ice Production ......................................................................................... 14

Ice Quality ............................................................................................... 15

Plumbing Problems ................................................................................ 15

ASSISTANCE OR SERVICE ...................................................................... 15

WARRANTY ............................................................................................... 16

[NDICE

SEGURIDAD DE LA FABRICA DE HIELO ............................................... 17

INSTRUCCIONES DE INSTALACION ...................................................... 17

Herramientas y piezas ............................................................................ 17

Dimensiones del panel hecho a la medida ............................................. 17

Desempaque la fabrica de hielo ............................................................. 19

Requisitos de ubicaci6n ......................................................................... 19

Requisitos electricos ............................................................................... 20

Requisitos del suministro de agua ......................................................... 20

Nivelaci6n ................................................................................................ 20

Conexi6n del suministro de agua ........................................................... 21

Conexi6n del desagQe ............................................................................ 22

Instale el panel de revestimiento hecho a la medida ............................. 23

Puerta de la fabrica de hielo ................................................................... 23

Sonidos normales ................................................................................... 25

USO DE LA FABRICA DE HIELO ............................................................. 25

C6mo funciona su fabrica de hielo ........................................................ 25

Uso de los controles ............................................................................... 26

CUlDADO DE LA FABRICA DE HIELO .................................................... 26

Limpieza .................................................................................................. 26

Cuidado durante las vacaciones y mudanzas ....................................... 28

SOLUCION DE PROBLEMAS ................................................................... 29

Funcionamiento de la fabrica de hielo ................................................... 29

Producci6n de hielo ................................................................................ 29

Calidad del hielo ..................................................................................... 30

Problemas de plomeria .......................................................................... 30

AYUDA O SERVlCIO TI_CNICO ................................................................ 30

GARANTiA ................................................................................................. 31

TABLEDESMATIERES

SI_CURITI_ DE LA MACHINE .&GLAQONS ............................................. 32

INSTRUCTIONS D'INSTALLATION ......................................................... 32

Outillage et pieces .................................................................................. 32

Dimensions du panneau personnalise ................................................... 32

Deballage de la machine a glagons ........................................................ 34

Exigences d'emplacement ..................................................................... 34

Specifications _lectriques ....................................................................... 35

Specifications de I'alimentation en eau.................................................. 35

Nivellement ............................................................................................. 35

Raccordement a la canalisation d'eau ................................................... 36

Raccordement au drain de vidange ....................................................... 37

Installation du panneau decoratif personnalise ...................................... 38

Porte de la machine a glagons ............................................................... 38

Sons normaux ......................................................................................... 40

UTILISATION DE LA MACHINE .&GLAQONS ........................................ 40

Fonctionnement de la machine &gla(_ons ............................................. 40

Utilisation des commandes .................................................................... 41

ENTRETIEN DE LA MACHINE .&GLAQONS ........................................... 41

Nettoyage ............................................................................................... 41

Precautions & prendre avant les vacances ou un demenagement ....... 43

DI':PAN NAGE ............................................................................................. 44

Fonctionnement de la machine &gla(_ons ............................................. 44

Production de gla(_ons ........................................................................... 45

Qualit6 des gla(_ons ................................................................................ 45

Problemes de plomberie ........................................................................ 45

ASSISTANCE OU SERVICE ...................................................................... 46

GARANTIE .................................................................................................. 47

ICE MAKERSAFETY

Your safety and the safety of others are very important.

We have provided many important safety messages in this manual and on your appliance. Always read and obey all safety

messages.

This is the safety alert symbol.

This symbol alerts you to potential hazards that can kill or hurt you and others.

All safety messages will follow the safety alert symbol and either the word "DANGER" or "WARNING."

These words mean:

You can be killed or seriously injured if you don't immediately

follow instructions.

You can be killed or seriously injured if you don't follow

instructions.

All safety messages will tell you what the potential hazard is, tell you how to reduce the chance of injury, and tell you what can

happen if the instructions are not followed.

IMPORTANT SAFETY INSTRUCTIONS

WARNING: To reduce the risk of fire, electric shock, or injury when using your ice maker, follow these basic

precautions:

• Plug into a grounded 3 prong outlet.

• Do not remove ground prong.

• Do not use an adapter.

• Do not use an extension cord.

• Disconnect power before cleaning.

• Disconnect power before servicing.

• Replace all parts and panels before operating.

• Use two or more people to move and install ice maker.

SAVE THESE INSTRUCTIONS

INSTALLATIONINSTRUCTIONS

TOOLS NEEDED:

Gather the required tools and parts before starting installation.

Read and follow the instructions provided with any tools listed

here.

• Cordless drill • Masking tape

• Phillips screwdriver • Tape measure

• Router or planer • Towel or piece of

cardboard

• Pencil

PARTS NEEDED:

Custom Overlay Door Panel--See "Custom Panel Installation

Instructions," #8 x 1/2"pan head wood screws (8)

PARTS SUPPLIED:

• Adhesive pads (4)

Cu m_n® Dm®nsons

If you plan to install a custom overlay panel, you will need to make

the panel yourself or consult a qualified cabinetmaker or

carpenter.

IMPORTANT:

• The thickness of the overlay panel must be 3/4"(1.91 cm).

• Overlay panel must not weigh more than 8 Ibs (3.62 kg).

• Overlay panels weighing more than recommended may

cause damage to your ice maker.

• Match wood grain direction with that of adjacent cabinets.

• Sand panel edges to provide a smooth finish.

• Use moisture sealer on both sides and all edges of the

panel to avoid damage from moisture.

Option I - Without Hinge-Side Spacer

To allow proper clearance for the door, prepare the custom

overlay panel using the dimensions shown.

2931/64"

(74.9 cm)

14 143%4"

(36.9crn)

11/4" /

(3.18 cm)

_1 f r3/4,,

1/4,,

(6.35 mm) i[_ _(1"91cm)

(1.91

11,/4"

(3.18cm)

1//4"

(6.35 mm)

Option 2 - With Hinge-Side Spacer

Toachieve aflush installationwith adjacent cabinets, prepare the

custom overlay panel using the dimensions shown.

Front of Panel

Top of Panel

(.95cm)

14%"

(37.1 cm)

(.95cm)

291/2"

(74.9 crn)

11,/4"

(3.18 cm)

k.i 1/,''

J---_T, (1.27 cm)

B C

A. Front - visible surface when installed

B. Hinge side

C. Notch to a depth of _" (0.95 cm)

Bottom of Panel

B C

f'_--_T 1/2"

/ _._L (1.27 cm)

11/4"

(3.18 cm)

A. Front - visible surface when installed

B. Hinge side

C. Notch to a depth of _" (0.95 cm)

ce Mc k®

Excessive Weight Hazard

Use two or more people to move and install ice maker.

Failure to do so can result in back or other injury.

Removing Packaging Materials

Remove tape and glue from your ice maker before using.

• To remove any remaining tape or glue from the exterior of the

ice maker, rub the area briskly with your thumb. Tape or glue

residue can also be easily removed by rubbing a small amount

of liquid dish soap over the adhesive with your fingers. Wipe

with warm water and dry.

Do not use sharp instruments, rubbing alcohol, flammable

fluids, or abrasive cleaners to remove tape or glue. Do not use

chlorine bleach on the stainless steel surfaces of the ice

maker. These products can damage the surface of your ice

maker.

Cleaning Before Use

After you remove all of the packaging materials, clean the inside of

your ice maker before using it. See the cleaning instructions in the

"Ice Maker Care" section.

Loc i£ on ements

To ensure proper ventilation for your ice maker, the front side

must be completely unobstructed. The ice maker may be

closed-in on the top and three sides, but the installation

should allow the ice maker to be pulled forward for servicing if

necessary.

Installation of the ice maker requires a cold water supply inlet

of V4"(6.35 mm) OD soft copper tubing with a shutoff valve

and either a gravity-drain system or condensate pump to

carry the water to an existing drain.

Choose a well ventilated area with temperatures above 55°F

(13°C) and below 110°F (43°C). Best results are obtained

between 70°F (21°C) and 90°F (32°C).

The ice maker must be installed in an area sheltered from the

elements, such as wind, rain, water spray, or drip.

Choose a location where the floor is even. It is important for

the ice maker to be level in order to work properly. If needed,

you can adjust the height of the ice maker by changing the

height of the leveling legs. See "Leveling."

When installing the ice maker under a counter, follow the

recommended opening dimensions shown. Place electrical

and plumbing fixtures in the recommended location as shown.

NOTES:

• Be sure the power supply cord is not pinched between the

ice maker and the cabinet.

• Be sure the water supply line is not pinched between the

ice maker and the cabinet.

• Be sure the drain line (on some models) is not pinched

between the ice maker and the cabinet.

Option I - Without Hinge-Side Spacers

34"

(86.4 cm)

Min.

341/2"

(87.6 cm)

Max.

24"

60.1 cm)

I 281/2.

(72.4 cm)

(38.1 cm)

A.Recommended location for electrical andplumbing fixtures

B.Floor level

Option 2 - With Hinge-Side Spacers

34"

(66.4 cm)

Min.

341/2"

(67.6 cm)

Max.

281/2"

(72.4 cm)

A. Recommended location for electrical and plumbing fixtures

B. Hinge-side, back spacer (Install 6" [15.24 cm] from back

wall to aid in drain alignment)

C. Hinge-side front spacer (Install flush with front face of

adjacent cabinet)

E®ct cca ,,, ,,.........

Electrical Shock Hazard

Plug into a grounded 3 prong outlet.

Do not remove ground prong.

Do not use an adapter.

Do not use an extension cord.

Failure to follow these instructions can result in death,

fire, or electrical shock.

Before you move your ice maker into itsfinal location, it is

important to make sure you have the proper electrical connection:

A 115 Volt, 60 Hz., AC only, 15- or 20-amp electrical supply,

properly grounded in accordance with the National Electrical

Code and local codes and ordinances, is required.

It is recommended that a separate circuit, serving only your ice

maker, be provided. Use a receptacle which cannot be turned off

by a switch or pull chain.

IMPORTANT: If this product is connected to a GFCI (Ground Fault

Circuit Interrupter) equipped outlet, nuisance tripping of the power

supply may occur, resulting in loss of cooling. Ice quality may be

affected. If nuisance tripping has occurred, and if the condition of

the ice appears poor, dispose of it.

Recommended grounding method

The ice maker must be grounded. The ice maker is equipped with

a power supply cord having a 3 prong grounding plug. The cord

must be plugged into a mating, 3 prong, grounding-type wall

receptacle, grounded in accordance with the National Electrical

Code and local codes and ordinances. If a mating wall receptacle

is not available, it is the personal responsibility of the customer to

have a properly grounded, 3 prong wall receptacle installed by a

qualified electrician.

If the water pressure to the reverse osmosis system is less than

40 to 60 psi (276 to 414 kPa):

• Check to see whether the sediment filter in the reverse

osmosis system is blocked. Replace the filter if necessary.

• Allow the storage tank on the reverse osmosis system to refill

after heavy usage.

If you have questions about your water pressure, call a licensed,

qualified plumber.

It is important for the ice maker to be level in order to work

properly. Depending upon where you install the ice maker, you

may need to make several adjustments to level it. You may also

use the leveling legs to lower the height of the ice maker for

undercounter installations.

Tools needed:

Gather the required tools and parts before starting installation.

• 9" level

• Adjustable wrench

NOTE: It is easier to adjust the leveling legs if you have another

person to assist you.

1. Move the ice maker to its final location.

NOTE: If this is a built-in installation, move the ice maker as

close as possible to the final location.

Place the level on top of the product to see if the ice maker is

level from front to back and side to side.

3. Push up on the top front of the ice maker, and then locate the

leveling screws that are on the bottom front of the ice maker.

4. Using an adjustable wrench, change the height of the legs as

follows:

• Turn the leveling leg to the right to lower that side of the

ice maker.

• Turn the leveling leg to the left to raise that side of the ice

maker.

NOTE: The ice maker should not wobble. Use shims to add

stability when needed.

A cold water supply with water pressure of between 30 and

120 psi (207 and 827 kPa) is required to operate the ice maker. If

you have questions about your water pressure, call a licensed,

qualified plumber.

Reverse Osmosis Water Supply

IMPORTANT:

Reverse osmosis water filtration systems can be used only

with ice maker installations that have a gravity drain. A reverse

osmosis system is not recommended for ice makers that have

a drain pump installed.

• The pressure of the water supply coming out of a reverse

osmosis system going to the water inlet valve of the ice maker

needs to be between 30 and 120 psi (207 and 827 kPa).

If a reverse osmosis water filtration system is connected to your

cold water supply, the water pressure to the reverse osmosis

system needs to be a minimum of 40 to 60 psi (276 to 414 kPa).

NOTE: The reverse osmosis system must provide 1 gal. (3.8 L) of

water per hour to the ice maker for proper ice maker operation. If

a reverse osmosis system is desired, only a whole-house capacity

reverse osmosis system, capable of maintaining the steady water

supply required by the ice maker, is recommended. Faucet

capacity reverse osmosis systems are not able to maintain the

steady water supply required by the ice maker.

5. Push up on the top rear of the ice maker and locate the

leveling legs that are on the bottom rear of the ice maker.

6. Follow the instructions in Step 4 to change the height of the

legs.

7. Use the level to recheck the ice maker to see that it is even

from front to back and side to side. If the ice maker is not

level, repeat steps 2 to 5. If the ice maker is level, go to the

"Connect Water Supply" section.

Read all directions before you begin.

IMPORTANT:

• Plumbing shall be installed in accordance with the

International Plumbing Code and any local codes and

ordinances.

Use copper tubing or Whirlpool supply line, Part Number

8212547RP, and check for leaks.

Install tubing only in areas where temperatures will remain

above freezing.

Tools needed:

Gather the required tools and parts before starting installation.

• Flat-blade screwdriver

• 7/le"and 1/2"open-end wrenches or two adjustable wrenches

• 1/4"nut driver

NOTE: Do not use a piercing-type or 34e"(4.76 mm) saddle valve

which reduces water flow and clogs more easily.

Connecting the Water Line

Turn off main water supply. Turn on nearest faucet long

enough to clear line of water.

Using a 1/2"copper supply line with a quarter-turn shutoff valve

or the equivalent, connect the ice maker as shown.

NOTE: To allow sufficient water flow to the ice maker a

minimum 1/2"size copper supply line is recommended.

I/ m

REAR VIEW

A. Water supply tube clamp

B. Vent hose (drain pump models only)

C. Inlet water tube clamp and supply

fine connector

D. Drain hose (drain pump models only)

Remove and discard the short, black plastic tube from the end

of the water line inlet.

Thread the nut onto the end of the tubing. Tighten the nut by

hand. Then tighten it with a wrench two more turns. Do not

overtighten.

NOTE: To avoid rattling, be sure the copper tubing does not

touch the cabinet's side wall or other parts inside the cabinet.

A. Bulb

B. Nut

Now you are ready to connect the copper tubing. Use 1/4"

(6.35 mm) OD soft copper tubing for the cold water supply.

• Ensure that you have the proper length needed for the job.

Be sure both ends of the copper tubing are cut square.

Slip compression sleeve and compression nut on copper

tubing as shown. Insert end of tubing into outlet end

squarely as far as it will go. Screw compression nut onto

outlet end with adjustable wrench. Do not overtighten.

A. Compression sleeve

B. Compression nut

C. Copper tubing

Place the free end of the tubing into a container or sink, and

turn on main water supply and flush out tubing until water is

clear. Turn off shutoff valve on the water pipe.

NOTE: Always drain the water line before making the final

connection to the inlet of the water valve to avoid possible

water valve malfunction.

Bend the copper tubing to meet the water line inlet which is

located on the back of the ice maker cabinet as shown. Leave

a coil of copper tubing to allow the ice maker to be pulled out

of the cabinet or away from the wall for service.

A B C D

A. Line to ice maker

B. Nut (purchased)

C. Ferrule (purchased)

D. Suppfied fine from ice maker

8. Install the water supply tube clamp around the water supply

line to reduce strain on the coupling.

9. Turn shutoff valve ON.

10. Check for leaks. Tighten any connections (including

connections at the valve) or nuts that leak.

_SG_s Co_' _;%ec_o_'

Gravity Drain System

Connect the ice maker drain to your drain in accordance with all

state and local codes and ordinances. Ifthe ice maker is provided

with a gravity drain system, follow these guidelines when installing

drain lines. This will help keep water from flowing back into the ice

maker storage bin and potentially flowing onto the floor causing

water damage.

• Drain lines must have a minimum of 5/8"(15.88 mm) inside

diameter.

Drain lines must have a 1" drop per 48" (2.54 cm drop per

122 cm) of run or 1/4"drop per 12" (6.35 mm per 30.48 cm) of

run and must not have low points where water can settle.

The floor drains must be large enough to accommodate

drainage from all drains.

The ideal installation has a standpipe with a 1Y2"(3.81 cm) to

2" (5.08 cm) PVC drain reducer installed directly below the

outlet of the drain tube as shown. You must maintain a

1" (2.54 cm) air gap between the drain hose and the

standpipe.

It may be desirable to insulate the drain line thoroughly up to

the drain inlet.

SIDE VIEW

(5 cm - 3.8 cm)

A. Drain hose

B. 1" (2.54 cm) air gap

C. PVC drain reducer

D. Center of drain should be 23" (58.4 cm) from front of door,

with or without the 3/4"(1.91 cm) panel on the door. The

drain should also be centered from left to right (7¾8"

[18.56 cm] from either side of the ice maker) unless

instalfing with a spacer.

Drain Pump System (on some models)

Connect the ice maker drain to your drain in accordance with the

International Plumbing Code and any local codes and ordinances.

NOTE: Ifthe drain hose becomes twisted and water cannot drain,

your ice maker will not work.

Connecting the Drain

After ensuring that the drain system is adequate, follow these

steps to properly place the ice maker:

Electrical Shock Hazard

Plug into a grounded 3 prong outlet.

Do not remove ground prong.

Do not use an adapter.

Do not use an extension cord.

Failure to follow these instructions can result in death,

fire, or electrical shock.

Excessive Weight Hazard

Use two or more people to move and install ice maker.

Failure to do so can result in back or other injury.

2. Style 1 - For gravity drain system, push the ice maker into

position so that the ice maker drain tube is positioned over the

PVC drain reducer. See "Gravity Drain System."

Style 2 - For drain pump system connect the drain pump

outlet hose to the drain. See "Drain Pump System."

3. Recheck the ice maker to be sure that it is level. See

"Leveling."

4. If it is required by your local sanitation code, seal the cabinet

to the floor with an approved caulking compound after all

water and electrical connections have been made.

IMPORTANT: Create custom overlay panel according to the

specifications in the "Custom Overlay Panel" section.

1. Install the ice maker.

2. Level the ice maker. See "Leveling."

3. Place the ice maker under the cabinet so that the front edge of

the custom panel will align with the front edge of the

surrounding cabinets.

4. Hold the custom panel up to the ice maker and check that the

opening and alignment are correct. Mark location of the panel

as necessary.

5. Remove the tape from the face of the door.

6. Remove the paper backing from the adhesive pads that are

located on the door front.

7. Place the panel on the door, align with markings and apply

pressure in the area of the adhesive pads.

8. Make sure the ice maker door opens and closes easily.

9. Pull the ice maker forward to access the top and sides of the

door.

10. Remove the gaskets from the interior door panel and set

aside.

11. Using the factory drilled holes as a guide, use a scribe and

mark the drilling locations on the overlay panel.

12. Drill eight V8"x W' (3.18 mm x 12.7 mm) deep holes into the

overlay panel.

NOTE: Do not drill deeper than W' (12.7 mm).

13. Use eight #8 x W' pan-head wood screws to attach the panel

to the door.

14. Attach a handle if necessary.

15. Replace the gaskets on the inner door panel.

16. Move the ice maker back into place under the counter.

1. Plug into a grounded 3 prong outlet.

OptionI - Without Hinge-Side Spacer

2931/_4 ''

(73.0 cm)

(

1433/64

(36.9 cm)._

A. #8 x ½" Pan-head wood screw

B.Adhesive pads

C. Custom panel

Option 2 - With Hinge-Side Spacer

291/2"

(74.9 cm)

A. #8 x ½" Pan-head wood screw

B.Adhesive pads

C. Custom panel

ce Mc k® ©

Tools needed:

Gather the required tools and parts before starting installation.

• 5/le"wrench • Flat putty knife

• V4"wrench • Phillips screwdriver

Hinge pin

Handlescrew

5_6" Hex-head hinge screw

End cap screw

Remove Door

1. Unplug ice maker or disconnect power.

2. Remove the handle screws and handle from the top of the

door (on some models). Keep the parts together and set them

aside.

3. Remove the hinge pin from the top hinge.

4. Remove the door from the hinges and screw the top hinge pin

back into the top hinge.

5. Remove the door skin (on some models) as follows:

• Remove the two screws from the top and bottom of the

door skin.

• Remove the skin and the edge covers from the door. Keep

the parts together and set them aside.

Reverse the door end caps as follows:

• Remove the screw and end cap from the top corner. Move

it diagonally to the opposite side's bottom corner, keeping

the straight side of the end cap facing the front of the ice

maker.

Remove the screw and end cap from the bottom corner.

Move it diagonally to the opposite side's top corner,

keeping the straight side of the end cap facing the front of

the ice maker.

A B

D C

C D

B A

A. Top corner open (no end cap)

B. Beginning top corner end cap

C. Beginning bottom corner end cap

D. Bottom corner open (no end cap)

7. Place the door back into the skin, keeping the edge covers in

place. Replace the two screws in the top and bottom.

8. Set the door aside.

Reverse Hinges

1. Unscrew and remove the top hinge. Replace the screws in the

empty hinge holes.

2. Remove the screws from the bottom of the opposite side of

the ice maker cabinet. Turn the top hinge upside down so that

the hinge pin points up. Place the hinge on the bottom

opposite side of the ice maker and tighten screws.

3. Remove the plastic hinge pin sleeve from the "old" bottom

hinge and replace it on the new bottom hinge pin.

4. Remove the "old" bottom hinge screws and hinge. Replace

the screws in the empty hinge holes.

5. Remove the screws from the top of the opposite side of the

ice maker cabinet. Turn the hinge upside down so that the

hinge pin points down. Place the hinge on the top opposite

side of the ice maker and tighten the screws.

6. Remove the top hinge pin.

Replace Door

1. Place plastic hinge pin sleeve in the top hinge hole on the

door. Align the door with the top hinge hole and replace the

top hinge pin.

2. Replace the handle and handle screws (on some models).

Top Hinge

c...........................

D .....

A. Hinge pin

B. Hinge pin sleeve

C. Hinge

D. Hex-head hinge screw

Bottom Hinge

Reverse Door Catch

1. Remove the hole plugs from the opposite side of the door and

set aside.

2. Remove the screws from the magnetic door catch and replace

it on the opposite side of the door.

Push the hole plugs into place on the opposite side of the

door.

A. Hex-head hinge screw

B. Hinge pin sleeve

C. Hinge

D. Hinge pin

Electrical Shock Hazard

Plug into a grounded 3 prong outlet.

Do not remove ground prong.

Do not use an adapter.

Do not use an extension cord.

Failure to follow these instructions can result in death,

fire, or electrical shock.

4. Plug into a grounded 3 prong outlet.

Your new ice maker may make sounds that are not familiar to you.

Because the sounds are new to you, you might be concerned

about them. Most of the new sounds are normal. Hard surfaces

such as floors, walls and cabinets can make the sounds seem

louder than they actually are. The following describes the kinds of

sounds that might be new to you and what may be making them.

• You will hear a buzzing sound when the water valve opens to

fill the water reservoir for each cycle.

• Rattling noises may come from the flow of the refrigerant or

the water line. Items stored on top of the ice maker can also

make noises.

The high-efficiency compressor may make a pulsating or high

pitched sound.

Water running over the evaporator plate may make a

splashing sound.

Water running from the evaporator plate to the water reservoir

may make a splashing sound.

As each cycle ends, you may hear a gurgling sound due to the

refrigerant flowing in your ice maker.

You may hear air being forced over the condenser by the

condenser fan.

During the harvest cycle, you may hear a "thud" when the ice

sheet slides from the evaporator onto the cutter grid.

When you first start the ice maker, you may hear water running

continuously. The ice maker is programmed to run a rinse

cycle before it begins to make ice.

ICE MAKERUSE

When you first start your ice maker, the water pan will fill and the

system will rinse itself before starting to make ice. The rinsing

process takes about 5 minutes.

Under normal operating conditions, the ice maker will cycle at

preset temperatures. The ice level sensor located in the ice

storage bin will monitor the ice levels.

IMPORTANT:

• If the water supply to the ice maker is turned off, be sure to set

the ice maker control to OFE

• The ice maker is designed to make clear ice from the majority

of water sources on a daily basis. If your results are

unsatisfactory, your water may need to be filtered or treated.

The Ice Making Process

1. Water is constantly circulated over a freezing plate. As the

water freezes into ice, the minerals in the water are rejected.

This produces a sheet of ice with a low mineral content.

2. When the desired thickness is reached, the ice sheet is

released and slides onto a cutter grid. The grid divides the

sheet into individual cubes.

3. The water containing the rejected minerals is drained after

each freezing cycle.

4. Fresh water enters the machine for the next ice making cycle.

Cubes fall into the storage bin. When the bin is full, the ice

maker shuts off automatically and restarts when more ice is

needed. The ice bin is not refrigerated, and some melting will

occur. The amount of melting varies with room temperature.

NOTE: As the room and water temperatures vary, so will the

amount of ice produced and stored. This means that higher

operating temperatures result in reduced ice production.

To start the normal ice making cycle, press ON.

To stop ice maker operation, press OFE

O._£.n Speed Clean

Off ice Service Reset

0-0-0-0

NOTES:

• Pressing the ON/OFF switch does not shut off power to

the ice maker.

• Allow 24 hours to produce the first batch of ice. Discard

the first batch produced.

Speed Ice Mode

Select the Speed Ice feature when you have an upcoming need

for a large amount of ice and the ice bin is low or empty. The

Speed Ice mode will produce a greater quantity of ice in a24-hour

period.

• Press and hold SPEED ICE while the ice maker is on. The

indicator light will illuminate.

• Press and hold SPEED ICE again to turn off the Speed Ice

feature. The indicator light will turn off.

Service

The service light indicates when service is needed. If the service

light turns on, turn the ice maker off and back on. If the service

light turns on again, call for service.

Clean/Reset

The Clean/Reset Status light will help you know when it is time to

clean your ice maker. The light will change to yellow. This tells you

it is almost time to clean your ice maker. It is recommended that

you clean the ice maker when the status light changes to red OR

ice production decreases significantly. To clean your ice maker,

see "Ice Maker System" in the "Cleaning" section.

ICE MAKERCARE

The ice making system and the air cooled condenser need to be

cleaned regularly for the ice maker to operate at peak efficiency

and to avoid premature failure of system components. See the

"Ice Maker System" and the "Condenser" sections.

Exterior Surfaces

Wash the exterior enamel surfaces and gaskets with warm water

and mild soap or detergent. Wipe and dry. Regular use of a good

household appliance cleaner and wax will help maintain the finish.

Do not use abrasive cleaners on enamel surfaces as they may

scratch the finish.

For products with a stainless steel exterior, use a clean sponge or

soft cloth and a mild detergent in warm water. Do not use abrasive

or harsh cleaners. Do not use chlorine bleach on the stainless

steel surfaces.

Ice Maker System

Minerals that are removed from water during the freezing cycle will

eventually form a hard scaly deposit in the water system. Cleaning

the system regularly helps remove the mineral scale buildup. How

often you need to clean the system depends upon how hard your

water is. With hard water of 15 to 20 grains/gal. (4 to 5 grains/

liter), you may need to clean the system as often as every

6 months.

NOTE: Use one 16 oz (473 mL) bottle of approved ice maker

cleaner. To order, call 1-800-JENNAIR and ask for Part Number

4396808. In Canada, call 1-800-807-6777.

1. Press the selector switch to OFR

2. Wait 5 to 10 minutes for the ice to fall into the storage bin.

Remove all ice from the storage bin.

3. Unscrew the drain cap from the bottom of the water pan

located inside the storage bin as shown. Allow the water to

drain completely.

4. Replace the drain cap securely on the water pan. If the drain

cap is loose, water will empty from the water pan and you will

have either thin ice or no ice.

5. Read and follow all handling information on the cleaner bottle

before completing the steps below. Use one 16 oz (473 mL)

bottle of approved ice maker cleaner.

6. Pour one bottle of solution into the water pan. Fill the bottle

twice with tap water and pour it into the water pan.

After the cleaning cycle is complete, remove the drain cap

from the water pan. Look for any cleaning solution left in the

water pan. If cleaning solution drains from the water pan, you

should run the clean cycle again. Be sure to replace the drain

cap securely on the water pan. If the drain cap is loose, water

will empty from the water pan and you will have either thin ice

or no ice.

NOTE: Severe scale buildup may require repeated cleaning with a

fresh quantity of cleaning solution.

9. Push the selector switch to ON to resume ice production.

Condenser

A dirty or clogged condenser:

• Obstructs proper airflow.

• Reduces ice making capacity.

• Causes higher than recommended operating temperatures

which may lead to component failure.

Electrical Shock Hazard

Disconnect power before cleaning.

Replace aii parts and panels before operating.

Failure to do so can result in death or electrical shock.

1. Unplug ice maker or disconnect power.

2. Remove the two screws in the lower access panel and the two

screws from the base grille area of the front panel support.

3. Pull the bottom forward and then pull down to remove the

lower access panel.

S .........

[ -Ixx qo \

1,L ",\ ....._ ..................A

/ "_"_ .. c

A. Waterpan

B. Water pan thumb screws

C. Drain cap

Press the CLEAN button. See "Using the Controls." The light

will blink, indicating that the cleaning cycle is in process.

When the indicator light turns green (approximately

70 minutes), the cleaning cycle is complete. During the

cleaning cycle, the system will both clean and rinse itself.

4, Remove dirt and lint from the condenser fins and the unit

compartment with a brush attachment on a vacuum cleaner.

5. Replace the lower access panel using the four screws.

6. Plug in ice maker or reconnect power.

Interior Components

1. Unplug ice maker or disconnect power.

2. Open the storage bin door and remove any ice that is in the

bin.

3. Remove the drain cap from the water pan and drain

thoroughly. Replace the drain cap securely on the water pan. If

the drain cap is loose, water will empty from the water pan,

and you will have either thin ice or no ice.

4. Remove the two screws that hold the cutter grid cover in

place and remove the cutter grid cover.

5. Unplug the wiring harness from the left side of the cutter grid.

A. Cutter grid cover

B. Screws

6. Unplug the ice level sensor from the right side of the cutter

grid. Pull the ice level sensor down and forward away from the

cutter grid.

7. Remove the right-hand and left-hand screws. Lift the cutter

grid up and out.

NOTE: Make sure the plastic spacer from the right-hand side

of the cutter grid bracket stays with the cutter grid.

A D

A. Cutter grid harness

B. Screw

C. Cutter grid

D. Ice level sensor harness

E.Plastic spacer

F. Screw

Remove the two thumb screws that hold the water pan in

place. Push down with one hand on the front of the pan while

pulling forward on the bottom back side.

B--

-|\\ qo \ --]

............._ ....................,4

A. Water pan

B. Water pan thumb screws

C. Drain cap

Remove, clean and replace the ice scoop and ice scoop

holder.

• After removing the ice scoop, remove the holder by

removing the two thumb screws.

• Wash the ice scoop holder along with the other interior

components using the following instructions.

• Replace the ice scoop holder by replacing the thumb

screws.

10.

A. Thumb screw

B. Ice scoop holder

Wash the interior components (cutter grid, exterior of hoses,

and water pan) and the storage bin, door gasket, ice scoop,

and ice scoop holder with mild soap or detergent and warm

water. Rinse in clean water. Then clean the same parts with a

solution of 1 tbs (15 mL) of household bleach in 1 gal. (3.8 L)

warm water. Rinse again thoroughly in clean water.

NOTE: Do not remove hoses. Do not wash plastic parts in

dishwasher. They cannot withstand temperatures above

145°F (63°C).

11. Replace water pan by pushing back on the bottom with one

hand while pushing up and back on the top. Secure the water

pan by replacing both screws.

12. Check the following:

• Drain cap from the water pan is securely in place. If the

drain cap is loose, water will empty from the water pan,

and you will have either thin ice or no ice.

13.

• Hose from water pan is inserted into storage bin drain

opening.

Slide the cutter grid back into place and secure it by replacing

the right-hand screw and plastic spacer. Then tighten the left-

hand screw. Reconnect the cutter grid harness and the ice

level sensor harness.

14. Replace the cutter grid cover and the two screws.

15. Gently wipe the control panel with asoft, clean dishcloth using

warm water and a mild liquid dish detergent.

16. Plug in ice maker or reconnect power.

17. After cleaning, make sure that all controls are set properly and

that no control indicators are flashing.

Electrical Shock Hazard

Disconnect power before servicing.

Replace all parts and panels before operating.

Failure to do so can result in death or electrical shock.

To shut down the ice maker:

1. Unplug ice maker or disconnect power.

2. Remove all ice from storage bin.

3. Shut off the water supply.

Remove the two screws in the lower access panel and the two

screws from the base grille area of the front panel support.

Pull forward to remove the lower access panel.

5. Disconnect the inlet and outlet lines to water valve. Allow

these lines to drain and then reconnect to the valve.

6. Replace lower access panel and screws.

7. Drain water from water pan by removing the drain cap.

8. If the room temperature will drop below 32°F (0°C), water must

be removed from the drain line.

For ice makers with a drain pump installed:

• Plug in ice maker or reconnect power.

• Turn ice maker off and remove all remaining ice from ice

bin.

Pour 1 qt (0.95 L) of water into the ice bin near the drain

and let the ice maker stand for approximately 5 minutes.

This will allow the water in the bin to drain into the drain

pump so that the pump will remove the remaining water

from the ice bin and the drain pump.

• Unplug ice maker or disconnect power.

9. Before using again, clean the ice maker and storage bin.

10. Plug into a grounded 3 prong outlet.

NOTE: All components of the ice maker are permanently

lubricated at the factory. They should not require any additional

oiling throughout the normal life of the machine.

TROUBLESHOOTING

Try the solutions suggested here first in order to avoid the cost of an unnecessary service call.

+>'d<II ,,,,J,= s,<+_++-i, ,4jI_+S_,>_+ i,%14 i,%+,=i, _,

Your ice maker will not operate

Electrical Shock Hazard

Plug into a grounded 3 prong outlet.

Do not remove ground prong.

Do not use an adapter.

Do not use an extension cord.

Failure to follow these instructions can result in death,

fire, or electrical shock.

Does the green light come on when the Clean button is

pushed? The ice maker is receiving power but may need

cleaning. See "Cleaning."

Does the ice maker have a drain pump? If there was a large

amount of water added to the ice maker, wait a few minutes

for the drain pump to clear. If there is still water in the bin,

check to see whether the drain hose is kinked.

Ice maker seems noisy

• Is water being circulated through the ice maker? This is

normal operation. Water is added once per ice-making cycle.

• Is the water in the reservoir overflowing? This is normal.

This overflow helps to purge minerals that were removed from

the water during the ice making process.

• Is there a "whooshing" sound? Check the following things:

• Make sure that the water supply is hooked up and turned

on.

• Make sure that the drain cap is tight and the water drain

pan pump is securely attached to the water pan.

Is there ice between the evaporator plate and the cutting

grid? Check that the ice maker is level. See "Leveling." If the

ice maker is level, and the problem persists, run a cleaning

cycle. See "Cleaning."

Is the power cord plugged in? Plug into a grounded 3 prong

outlet.

Is the control set to ON? Be sure that the control is set to

ON.

Has a household fuse blown, or has a circuit breaker

tripped? Replace the fuse or reset the circuit breaker. If the

problem continues, call an electrician.

msthe room temperature cooler than normal? Room

temperature must be above 55°F (13°C). Otherwise, bin

thermostat may sense cold room temperature and shut off

even though the bin is not full of ice. The ice maker may not

restart once it does shut off.

_ %,F %/£ %1%_ ' tl %/_</ /

Ice maker runs but produces no ice

• Is the control set to ON? Be sure that the control isset to

ON.

Is the water supply connected? Make sure the water supply

is properly connected and turned on.

Is the drain cap securely in place? If the drain cap is loose,

water will empty from the water pan, and you will have either

thin ice or no ice. Tighten the drain cap.

• Is there debris in the drain tube? Clean the drain tube.

• is there a kink in the drain line? Be sure that there are no

kinks in the line.

• Is the service light flashing on and off continually? Call for

service.

Ice maker runs but produces very little ice

Is the accelerated ice production feature turned on? This

feature increases the ice production rate to provide you with

more ice in the same amount of time. See "Using the

Controls."

• Is the room temperature hotter than normal? Room

temperatures of more than 90°F (32°C) will normally reduce

ice production.

Electrical Shock Hazard

Disconnect power before servicing.

Replace all parts and panels before operating.

Failure to do so can result in death or electrical shock.

Is the condenser dirty? Dirt or lint may be blocking the

airflow through the condenser. See "Condenser" in the

"Cleaning" section.

Is there scale buildup in the ice maker? If there iswhite

scale buildup in the ice maker's water or freezing system, you

should clean the ice maker. See "Interior Components" in the

"Cleaning" section.

Is the drain cap securely in place? If the drain cap is loose,

water will empty from the water pan, and you will have either

thin ice or no ice. Tighten the drain cap if it is loose.

Grid is not cutting ice sheets

Is the cutter grid securely in place? Check the cutter grid

harness plug to make sure the connection is intact. See

"Interior Components" section of "Cleaning" for instructions

on cutter grid removal.

C@ _£_;'__"__;__

Off taste, odor or gray color in the ice

• Is there unusually high mineral content in the water

supply? The water may need to be filtered or treated.

• Is there mineral scale buildup? Clean your ice maker. See

"Ice Maker System" in the "Cleaning" section.

• Are there food items stored in the ice bin? Do not store any

foods in the ice bin.

• Were all the packaging materials removed? Make sure that

all packaging materials were removed at the time of

installation.

Thin, soft or clumps of ice

Is there unusually high mineral content in the water

supply? The water may need to be filtered or treated.

Is there mineral scale buildup? Clean your ice maker. See

"Ice Maker System" in the "Cleaning" section.

Are there clumps of ice in the bin? If ice is not used regularly

it will melt and form clumps. Break the clumps with the ice

scoop provided.

Excessive Weight Hazard

Use two or more people to move and install ice maker.

Failure to do so can result in back or other injury.

• Is the drain hose aligned over the drain? Move the ice

maker to align the drain. See "Connect Water Supply."

NOTE: Service technicians cannot repair plumbing problems

outside of the ice maker. Call a licensed, qualified plumber.

ASSISTANCEOR SERVICE

If you need assistance or service, first see the "Troubleshooting"

section. Additional help is available. Call us at 1-800-JENNAIR

(1-800-536-6247) from anywhere in the U.S.A., or write:

Jenn-Air Brand Home Appliances

Customer eXperience Center

553 Benson Road

Benton Harbor, MI 49022-2692

Information may also be obtained by visiting our website at

www.jennair.com.

In Canada, for assistance, installation or service, call us at

1-800-807-6777, or write:

Jenn-Air Brand Home Appliances

Customer eXperience Centre

200 - 6750 Century Ave.

Mississauga, Ontario L5N 0B7

In Canada, visit www.jennair.ca.

Please include a daytime phone number in your correspondence.

JENN-AIR °

ice Maker

PRODUCT MODEL NUMBER

JIM158XXCX

Electficak A 115 Volt, 60 Hz.,AConly, 15- or 20-amp electricalsupply,

properly groundedin accordancewith the NationalElectricalCodeandlocal

codesand ordinances,is required.

Itis recommendedthat aseparatecircuit, serving onlyyour ice maker,be

provided. Useareceptaclewhich cannotbeturned off by aswitch or pull

chain.

Recommendedgrounding method:Theicemaker must begrounded.The ice

maker is equippedwith a powersupply cord havinga3 pronggrounding

plug.Thecord must be pluggedinto amating, 3 prong, grounding-typewall

receptacle,groundedin accordancewith the NationalBecticalCodeand local

codesand ordinances.

iMPORTANT:If this product is connectedto aGFCl(GroundFaultCircuit

Interrupter)equippedoutlet, nuisancetripping ofthe powersupply may

occur,resulting in loss of cooling. Foodquality andflavor maybeaffected. If

nuisancetripping hasoccurred,and if the condition of the food appearspoor,

disposeof it.

Water:A coldwater supply withwater pressurebetween30 and120 psi

(207 and827 kPa) isrequiredto operateice makerand water dispenser.If

you havequestionsabout your water pressure,calla licensed,qualified

plumber.

ReverseOsmosis WaterSupply:

[] Reverseosmosis waterfiltration systems canbe usedonly with icemaker

installationsthat havea gravitydrain.A reverseosmosis system is not

recommendedfor ice makersthat havea drain pump installed.

[] Thepressureof the watercoming out ofa reverseosmosis system going

to the waterinlet valveof the icemakerneedsto be between30 and

120 psi (207 and827 kPa).If a reverseosmosis waterfiltration system is

connectedto your cold watersupply,the waterpressureto the reverse

osmosissystem needsto bea minimum of 40 to 60 psi (207 and

827 kPa).

NOTE:Thereverseosmosissystem must provide 1gal. (3.8 L) of water per

hour to the icemakerfor proper ice makeroperation. If a reverseosmosis

systemis desired, onlyawhole-house capacityreverseosmosis system,

capableof maintainingthe steadywatersupply requiredbythe ice maker,is

recommended.

Location:

[] Toensureproper ventilationfor your ice maker,the front side must be

completely unobstructed.Theice maker may beclosed-in onthe top and

three sides, but the installationshould allowthe ice makerto bepulled

forward for servicingif necessary.

[] Installation ofthe ice makerrequiresacold watersupply inletof ¼"

(6.35 mm) ODsoft coppertubing with a shutoff valveand eithera gravity-

drainsystem or condensatepumpto carrythe waterto anexisting drain.

[] Chooseawell ventilatedareawith temperaturesabove55°F(13°C) and

below 110°F(43°0). Bestresultsareobtainedbetween70°F(21°0) and

90°F (32%).

[] Besurethe powersupply cord is not pinchedbetweenthe ice makerand

the cabinet.

[] Besurethe water supply line is not pinchedbetweenthe ice makerandthe

cabinet.

[] Besurethe drain line (onsome models) is not pinchedbetweenthe ice

maker andthe cabinet.

[] Choosea locationwherethe floor is even.It is important forthe ice maker

to be levelin orderto work properly.

DRAIN REQUIREMENTS

A. Watersupply tubeclamp

B. Venthose (drainpump models only)

C.Inlet watertubeclamp and supply

line connector

D. Drainhose (drain pump models only)

17/8"

(4.8 cm)

1" (2.54 cm)

20"

(50.8 cm)

2".11/2"

(5 cm - 3.8 cm)

A. Drain hose

B. 1"(2.54cm)

air gap

C.PVCdrain

reducer

D. Centerof drain should be23" (58.4 cm)

from front of door, with or without the

¼"(1.91 cm) panel on the door. The

drain should also be centeredfrom left

to right (7/6" [18.56 cm] from either

side of the icemaker).

Drain: Either a gravity-drain system or

condensatepump to carry water to an

existing drain.

[] Drain lines must havea minimum of %"

(15.88 mm) inside diameter.

[] Drain lines must havea 1" drop per 48"

(2.54 cm drop per 122 cm) of run or¼"

drop per 12"(6.35 mm per30.48 cm)

of run and must not havelow points

where water can settle.

[] Thefloor drains must be large enough

to accommodate drainage from all

drains.

[] The ideal installation has astandpipe

with a 1_" (3.81 cm) to 2" (5.08 cm)

PVCdrain reducer installed directly

belowthe outlet of the drain tube as

shown. You must maintain a 1" (2.54

cm) air gap betweenthe drain hose

andthe standpipe.

[] It may bedesirableto insulate the drain

linethoroughly upto the drain inlet.

Because Whirlpool Corporation policy includes a continuous commitment to improve Dimensions are for planning purposes only. For complete details, see Installation Ref.W10282143A

our products, we reserve the right to change materials and specifications without notice. Instructions packed with product. Specifications subject to change without notice. 11/22/10

Toallow proper clearancefor the door, preparethe custom overlaypanelusingthe dimensions shown.

CUSTOM PANEL DiMENSiONS

if you planto install a custom overlay panel,you will needto makethe panelyourself or consult a qualifiedcabinetmakeror carpenter.

IMPORTANT:

[] Thethicknessofthe overlaypanelmust be3/4"(1.91 cm).

[] Overlaypanelmust not weigh morethan 8 Ibs (3.62 kg).

[] Overlaypanelsweighing more than recommendedmay causedamageto

your ice maker.

[] Matchwood grain direction with thatof adjacentcabinets.

[] Sandpaneledgesto providea smooth finish.

[] Usemoisture sealeron both sidesand all edgesofthe panelto avoid

damagefrom moisture.

2931/64"

(74.9 cm)

.................................................................................................................143%4" ................................................................................

(36.9 crn)

11/4" / _ 11/4'

(3.16 cm) (3.18 cm)

3/4,,

1/4. (1.91 cm) (1.91 cm)_ _----_ _

(6.35 mm)

1/4"

(6.35 mm)

34 II

(86.4 cm)

Min.

341/2"

(87.6 cm)

Max.

24" ......................................................................B

60.1 cm)

(38.1cm)

A. Recommendedlocation for

electricalandplumbing fixtures.

B.Floor level

Because Whirlpool Corporation policy includes a continuous commitment to improve Dimensions are for planning purposes only. For complete details, see Installation Ref.W10282143A

our products, we reserve the right to change materials and specifications without notice. Instructions packed with product. Specifications subject to change without notice. 11/22/10

Toachieveaflush installationwith adjacentcabinets,preparethe custom overlaypanelusing the dimensionsshown.

CUSTOM PANEL DiMENSiONS

if you planto install a custom overlay panel,you will needto makethe panelyourself or consult a qualifiedcabinetmakeror carpenter.

IMPORTANT:

[] Thethicknessofthe overlaypanelmust be¾"(1.91 cm).

[] Overlaypanelmust not weigh morethan 8 Ibs (3.62 kg).

[] Overlaypanelsweighing more than recommendedmay causedamageto

your ice maker.

[] Matchwood grain direction with thatof adjacentcabinets.

[] Sandpaneledgesto providea smooth finish.

[] Usemoisture sealeron both sidesand all edgesofthe panelto avoid

damagefrom moisture.

14%"

(37.1 crn)

3/8,,

(.9S cm)

3/8"

(.9Scm)

-5

291/2"

(74.9 cm)

8" '

(15.2 cm)

281/2"

(72.4 cm)

24 II

A. Recommendedlocationfor electricaland plumbing fixtures.

B. Hinge-side, backspacer (Install 6"[15.24 cm] from back wall to aid in

drainalignment)

C.Hinge-side front spacer (Install flush with front face of adjacentcabinet)

11/4"

Topof Panel (3.18cm)

//T 1/2''

I ,,__.t± (1.27

A B C

Bottomof Panel A B C

[ f_T 1/2''

L .._ (1 27 cm)

11/4"

(3.18 cm)

A. Front- visible surface when installed

B. Hingeside

C.Notch to a depth of_" (0.95 cm)

Because Whirlpool Corporation policy includes a continuous commitment to improve Dimensions are for planning purposes only. For complete details, see Installation Ref.W10282143A

our products, we reserve the right to change materials and specifications without notice. Instructions packed with product. Specifications subject to change without notice. 11/22/10

JENN-AIRTM ICE MAKERWARRANW

LIMITED WARRANTY

For one year from the date of purchase, when this major appliance is operated and maintained according to instructions attached to or

furnished with the product, Jenn-Air brand of Whirlpool Corporation or Whirlpool Canada LP (hereafter "Jenn-Air") will pay for factory

specified parts and repair labor to correct defects in materials or workmanship that existed when this major appliance was purchased.

Service must be provided by a Jenn-Air designated service company. YOUR SOLE AND EXCLUSIVE REMEDY UNDER THIS LIMITED

WARRANTY SHALL BE PRODUCT REPAIR AS PROVIDED HEREIN. This limited warranty is valid only in the United States or Canada and

applies only when the major appliance is used in the country in which it was purchased. Proof of original purchase date is required to obtain

service under this limited warranty.

SECOND THROUGH FIFTH YEAR LIMITED WARRANTY ON SEALED REFRIGERATION SYSTEM PARTS

In the second through the fifth year from the date of purchase, when this major appliance is operated and maintained according to

instructions attached to or furnished with the product, Jenn-Air will pay for factory specified parts for the following components to correct

defects in materials or workmanship in the sealed refrigeration system that existed when this major appliance was purchased: compressor,

evaporator, condenser, dryer/strainer, and connecting tubing.

ITEMS EXCLUDED FROM WARRANTY

This limited warranty does not cover:

1. Replacement parts or repair labor if this major appliance is used for other than normal, single-family household use or when it is used in

a manner that is inconsistent to published user or operator instructions and/or installation instructions.

2. Service calls to correct the installation of your major appliance, to instruct you on how to use your major appliance, to replace or repair

house fuses, or to correct house wiring or plumbing.

3. Service calls to repair or replace appliance light bulbs, air filters or water filters. Consumable parts are excluded from warranty coverage.

4. Damage resulting from accident, alteration, misuse, abuse, fire, flood, acts of God, improper installation, installation not in accordance

with electrical or plumbing codes, or use of products not approved by Jenn-Air.

5. Cosmetic damage, including scratches, dents, chips or other damage to the finish of your major appliance, unless such damage results

from defects in materials or workmanship and is reported to Jenn-Air within 30 days from the date of purchase.

6. Any food or medicine loss due to refrigerator or freezer product failures.

7. Pickup and delivery. This major appliance is intended to be repaired in your home.

8. Repairs to parts or systems resulting from unauthorized modifications made to the appliance.

9. Expenses for travel and transportation for product service if your major appliance is located in a remote area where service by an

authorized Jenn-Air servicer is not available.

10. The removal and reinstallation of your major appliance if it is installed in an inaccessible location or is not installed in accordance with

Jenn-Air's published installation instructions.

11. Replacement parts or repair labor on major appliances with original model/serial numbers that have been removed, altered or cannot be

easily determined.

DISCLAIMER OF IMPLIED WARRANTIES

IMPLIED WARRANTIES, INCLUDING ANY IMPLIED WARRANTY OF MERCHANTABILITY OR IMPLIED WARRANTY OF FITNESS FOR A

PARTICULAR PURPOSE, ARE LIMITED TO ONE YEAR OR THE SHORTEST PERIOD ALLOWED BY LAW. Some states and provinces do not

allow limitations on the duration of implied warranties of merchantability or fitness, so this limitation may not apply to you. This warranty gives

you specific legal rights, and you also may have other rights that vary from state to state or province to province.

LIMITATION OF REMEDIES; EXCLUSION OF INCIDENTAL AND CONSEQUENTIAL DAMAGES

YOUR SOLE AND EXCLUSIVE REMEDY UNDER THIS LIMITED WARRANTY SHALL BE PRODUCT REPAIR AS PROVIDED HEREIN. JENN-

AIR SHALL NOT BE LIABLE FOR INCIDENTAL OR CONSEQUENTIAL DAMAGES. Some states and provinces do not allow the exclusion or

limitation of incidental or consequential damages, so these limitations and exclusions may not apply to you. This warranty gives you specific

legal rights, and you also may have other rights that vary from state to state or province to province.

If outside the 50 United States and Canada, contact your authorized Jenn-Air dealer to determine if another warranty applies.

If you think you need repair service, first see the "Troubleshooting" section of the Use & Care Guide. If you are unable to resolve the problem

after checking "Troubleshooting," additional help can be found by checking the "Assistance or Service" section or by calling Jenn-Air. In the

U.S.A., call 1-800-536-6247. In Canada, call 1-800-807-6777. 6/09

Keep this book and your sales slip together for future

reference. You must provide proof of purchase or installation

date for in-warranty service.

Write down the following information about your major appliance

to better help you obtain assistance or service if you ever need it.

You will need to know your complete model number and serial

number. You can find this information on the model and serial

number label located on the product.

Dealer name

Address

Phone number

Model number

Serial number

Purchase date

SEGURIDAD DELAFABRICA DEHIELO

Su seguridad y la seguridad de los demos es muy importante.

Hemos incluido muchos mensajes importantes de seguridad en este manual yen su electrodomestico. Lea y obedezca siempre

todos los mensajes de seguridad.

Este es el simbolo de advertencia de seguridad.

Este simbolo le llama la atenci6n sobre peligros potenciales que pueden ocasionar la muerte o una lesi6n a

usted y a los demas.

Todos los mensajes de seguridad iran a continuaci6n del simbolo de advertencia de seguridad y de la palabra

"PELIGRO" o "ADVERTENCIA". Estas palabras significan:

Si no sigue las instrucciones de inmediato, usted puede

morir o sufrir una lesibn grave.

Si no sigue las instrucciones, usted puede morir o sufrir

una lesibn grave.

Todos los mensajes de seguridad le diran el peligro potencial, le diran c6mo reducir las posibilidades de sufrir una lesi6n y Io que

puede suceder si no se siguen las instrucciones.

INSTRUCCIONES IMPORTANTES DE SEGURIDAD

ADVERTENOIA: Para reducir el riesgo de incendio, choque el6ctrico o lesiones personales al usar

la f&brica de hielo, siga estas precauciones b&sicas:

• Conecte a un contacto de pared de conexi6n a tierra de

3 terminales.

[] No quite el terminal de conexi6n a tierra.

• No use un adaptador.

• No use un cable electrico de extensi6n.

• Desconecte el suministro de energia antes de limpiarla.

• Desconecte el suministro de energia antes de darle

servicio.

[] Vuelva a colocar todos los componentes y paneles

antes de hacerla funcionar.

• Use dos o mas personas para mover e instalar la

fabrica de hielo.

GUARDE ESTAS INSTRUCCIONES

INSTRUCCIONESDEINSTALACION

HERRAMIENTAS NECESARIAS:

ReQna las herramientas y piezas requeridas antes de comenzar la

instalacion.

Lea y siga las instrucciones provistas con cualquiera de las

herramientas enlistadas aqui.

• Taladro inalambrico • Cinta adhesiva protectora

• Destornillador Phillips • Cinta de medir

• Contorneador o cepillo • Toalla o pedazo de carton

mecanico

• Lapiz

PIEZAS NEOESARIAS"

Panel de la puerta de revestimiento hecho a la medida - Vea

"lnstrucciones de instalacion del panel hecho a la medida",

tornillos para madera de cabeza de cono achatado #8 x 1/2"(8)

PIEZAS SUM IN ISTRADAS:

• Almohadillas adhesivas (4)

Si usted planea instalar un panel de revestimiento a la medida,

usted mismo necesitarA crear el panel o consultar a un ebanista o

carpintero calificado.

IMPORTANTE:

• El espesor del panel de revestimiento debe ser de 3/4"

(1,91 cm).

El panel de revestimiento no debe pesar m_s de 8 libras

(3,62 kg).

Los panels de revestimiento que pesan mas de Io

recomendado pueden causar daBo a su fabrica de hielo.

Haga coincidir la direcci6n de las vetas de la madera con

la de los armarios adyacentes.

Lije los bordes del panel para proporcionar un terminado

liso.

• Use sellador de humedad a ambos lados y todos los

bordes del panel para proporcionar protecci6n contra la

humedad.

La page charge ...

Jenn-Air JIM158XXRS1 Manuel utilisateur

Marque: Jenn-Air

Modèle: JIM158XXRS1

Taper: Manuel utilisateur

Ce manuel convient également à

Télécharger le PDF

rapport

dans d''autres langues

English: Jenn-Air JIM158XXRS1 User manual
español: Jenn-Air JIM158XXRS1 Manual de usuario

Jenn-Air JIM158XXRS1 Manuel utilisateur

Ce manuel convient également à

Jenn-Air JIM158XXRS1 Manuel utilisateur

dans d''autres langues

Documents connexes

Autres documents