RIDGID WD1956 Le manuel du propriétaire

WD19560

WD1956M1

16 U.S. GALLON / 60 Liter

PROFESSIONAL WET/DRY VAC

FOR QUESTIONS OR INFORMATION CONTACT US AT

CALL 1-800-4-RIDGID (1-800-474-3443) OR

www.RIDGIDvacs.com

Part No. SP6731 Printed in Mexico

OWNER’S MANUAL

SAVE THIS MANUAL FOR FUTURE REFERENCE

Thank you for buying a RIDGID product. • Español - página 21

• Français - page 41

WARNING:

To reduce the risk of injury, the user must read and understand the owner’s manual

before using this product.

!

SP6731-6 16 Gallon ESF 2018.qxp_SP6731 2/21/18 8:14 PM Page 1

2

Table of Contents

Section Page

Introduction . . . . . . . . . . . . . . . . . . . . . . 4

Unpacking and Checking

Carton Contents . . . . . . . . . . . . . . . . . 4

Removing/Installing The Metal Handle . 6

Drum/Caddy Assembly . . . . . . . . . . . . . 8

Wet/Dry Vac Assembly . . . . . . . . . . . . . 9

Operation. . . . . . . . . . . . . . . . . . . . . . . 10

Vacuuming Dry Materials . . . . . . . . . 10

Section Page

Vacuuming Liquids . . . . . . . . . . . . . . 11

Emptying the Drum. . . . . . . . . . . . . . 11

Blowing Feature . . . . . . . . . . . . . . . . 11

Accessory and Hose Storage . . . . . . . 13

Maintenance . . . . . . . . . . . . . . . . . . . . 14

Repair Parts. . . . . . . . . . . . . . . . . . . . . 16

Warranty . . . . . . . . . . . . . . . . . . . . . . . 20

IMPORTANT SAFETY INSTRUCTIONS

Safety is a combination of using common

sense, staying alert, and knowing how your

Wet/Dry Vacuum Cleaner (“Vac”) works.

Safety Signal Words

DANGER: Indicates a hazardous

situation which, if not avoided, will result

in death or serious injury.

WARNING: Indicates a hazardous

situation which, if not avoided, could

result in death or serious injury.

CAUTION: Indicates a hazardous

situation which, if not avoided, could

result in minor or moderate injury.

When using your Vac, always follow basic

safety precautions including the following:

WARNING

- To reduce the risk of fire,

electric shock, or injury:

• Read and understand this manual and

all labels on the Vac before operating.

• Use only as described in this manual.

• Do not leave Vac running while

unattended - you may fail to notice

important signs indicating abnormal

operation such as loss of suction,

debris/liquid exiting exhaust, or

abnormal motor noises. Immediately

stop using Vac if you notice these

signs.

• Do not leave Vac when plugged in.

Unplug from outlet when not in use

and before servicing.

• Sparks inside the motor can ignite

flammable vapors or dust. To reduce

the risk of fire or explosion, do not use

!

near combustible liquids, gases, or

dusts, such as gasoline or other fuels,

lighter fluid, cleaners, oil-based paints,

natural gas, coal dust, magnesium

dust, grain dust, aluminum dust, or gun

powder.

• Do not vacuum anything that is burning

or smoking, such as cigarettes,

matches, or hot ashes.

• Do not vacuum drywall dust, cold

fireplace ash, or other fine dusts with

standard filter. These may pass

through the filter and be exhausted

back into the air. Use a fine dust filter

instead.

• To reduce the risk of inhaling toxic

vapors, do not vacuum or use near

toxic or hazardous materials.

• To reduce the risk of electric shock,

do not expose to rain or allow liquid

to enter motor compartment.

Store indoors.

• This Wet/Dry Vac is not intended for

use by persons (including children) with

reduced physical, sensory, or mental

capabilities, or lack of experience and

knowledge, unless they have been

given supervision or instruction

concerning use of the appliance by a

person responsible for their safety.

• Do not allow to be used as a toy.

Close attention is necessary when

used by or near children.

• Do not use with a torn filter or without

filter installed except when vacuuming

liquids as described in this manual.

Dry debris ingested by the impeller

may damage the motor or be

exhausted into the air.

SP6731-6 16 Gallon ESF 2018.qxp_SP6731 2/21/18 8:14 PM Page 2

3

•To reduce the risk of personal injury or

damage to Vac, use only RIDGID

recommended accessories.

•When using as a blower:

- Direct air discharge only at work

area.

- Do not direct air at bystanders.

- Keep children away when blowing.

- Do not use blower for any job except

blowing dirt and debris.

- Do not use as a sprayer.

•To reduce the risk of eye injury, wear

safety eyewear. The operation of any

utility Vac or blower can result in

foreign objects being blown into the

eyes, which can result in severe eye

damage.

• Turn off Vac before unplugging.

• To reduce the risk of injury from

accidental starting, unplug power cord

before changing or cleaning filter.

• Do not unplug by pulling on cord.

To unplug, grasp the plug, not the cord.

• Do not use with damaged cord, plug or

other parts. If your Vac is not working

as it should, has missing parts, has

been dropped, damaged, left outdoors,

or dropped into water, call customer

service.

• Do not pull or carry by cord, use cord

as handle, close a door on cord, or pull

cord around sharp edges or corners.

Do not run Vac over cord. Keep cord

away from heated surfaces.

• Do not handle plug, switch, or the Vac

with wet hands.

• Use only extension cords that are rated

for outdoor use. Extension cords in

poor condition or too small in wire size

can pose fire and shock hazards.

To reduce the risk of these hazards,

be sure the cord is in good condition

and that liquid does not contact the

connection. Do not use an extension

cord with conductors smaller than

16 gauge (AWG) in size. To reduce

power loss, use a 14 gauge extension

cord if 25 to 50 ft. (8 to 15 m) long and

12 gauge for 50 ft. (15 m) or longer.

• This Vac is double-insulated,

eliminating the need for a separate

grounding system. Use only identical

replacement parts. Read the

instructions for Servicing Double-

Insulated Wet/Dry Vacs.

• Do not put any object into ventilation

openings. Do not vacuum with any

ventilation openings blocked; keep free

of dust, lint, hair or anything that may

reduce air flow.

• Keep hair, loose clothing, fingers, and

all parts of body away from openings

and moving parts.

• To reduce the risk of falls, use extra

care when cleaning on stairs.

• To reduce the risk of back injury or

falls, do not lift a Vac that is heavy

with liquid or debris. Partially empty

by scooping debris or draining liquid.

Observe the following warnings that

appear on the motor housing of your Vac:

WARNING: For your own safety,

read and understand owner’s

manual. Do not run unattended.

Do not pick up hot ashes, coals,

toxic, flammable or other hazardous

materials. Do not use around

explosive liquids or vapors.

WARNING: To reduce the risk of

electric shock - do not expose to

rain - store indoors.

DOUBLE INSULATED

GROUNDING NOT REQUIRED.

WHEN SERVICING USE ONLY

IDENTICAL REPLACEMENT PARTS.

!

SAVE THIS MANUAL

CAUTION:

• To reduce the risk of hearing damage,

wear ear protectors when using for

extended time or a noisy area.

• For dusty operations, wear dust mask.

• Static shocks are common when the

relative humidity of the air is low.

Vacuuming fine debris with your Vac can

deposit static charge on the hose or

Vac. To reduce the frequency of static

shocks in your home or when using this

Vac, add moisture to the air with a

humidifier.

!

SP6731-6 16 Gallon ESF 2018.qxp_SP6731 2/21/18 8:14 PM Page 3

Unpacking and Checking Carton Contents

4

Refer to the assembly sketch for

positioning of parts.

Remove contents of carton. Check each

item against the Carton Contents List.

Call 1-800-4-RIDGID (1-800-474-3443)

or E-mail us at [email protected]

if any parts are damaged or missing.

Long Phillips Screwdriver

Tools Required

MalletHammer

Carton Contents List

Key Description Qty

A Wet/Dry Vac Assembly.................1

B Dual-Flex™ Locking Hose ...........1

C Utility Nozzle ................................1

D Wet Nozzle...................................1

E Crevice Nozzle.............................1

F Car Nozzle ...................................1

G Extension Wands .........................2

H* Qwik Lock™ Filter........................1

I Owner’s Manual...........................1

* These items may come preassembled.

If they are not present in the carton check

the Vac power head to see if they are

preassembled.

B

H

I

D

E

G

F

A

C

Introduction

This Professional Wet/Dry Vac is

intended for household use. It may be

used for vacuuming wet or dry media and

may be used as a blower.

Read this owner’s manual to familiarize

yourself with the product features and to

understand the specific usage of your

new Vac.

SP6731-6 16 Gallon ESF 2018.qxp_SP6731 2/21/18 8:14 PM Page 4

JK

L

N

O

M

5

Unpacking and Checking Carton

Contents (continued)

Key Description Qty

Carton - Containing the following parts:

J Storage Bag......................................1

K Rear Wheels.....................................2

L Metal Handle ....................................1

M Shaft .................................................1

N Caddy, Right .....................................1

O Caddy, Left .......................................1

Key Description Qty

Bag of Loose Parts -

Containing the following:

P Casters .............................................2

Q Cap Nuts...........................................2

R Wheel Caps ......................................2

S Screws, Type AB #10 x 3/4” (19 mm)..8

P

R

S

Q

SP6731-6 16 Gallon ESF 2018.qxp_SP6731 2/21/18 8:14 PM Page 5

Removing/Installing the Metal Handle

6

Your Metal handle comes packaged in

the carton in the reverse direction.

You must pull the metal handle

completely out of Vac and reinstall the

handle in the correct direction, bent area

facing away from the back of the Vac,

before continuing.

Installing Handle

Press and hold release buttons while

installing handle into handle receptacles

in drum (See illustration).

NOTE: An audible snap of release

buttons indicates successful engagement

of handle.

Lowering Handle for Storage

To store Wet/Dry Vac, press and hold

release buttons while firmly sliding handle

down.

Removing Handle

Press and hold release buttons, as

shown. While firmly pushing in release

buttons, pull handle upwards to remove

(see illustration).

Installing Tool Holder

Install tool holder as shown with

extension wand holders facing unit.

Correct

Position

Storage

Position

Moving

Position

Metal Handle in

Reversed Position

(As Shipped)

Tote Snaps Tote

Straps (5)

Handle

Extension

Wand

Storage

Locations

SP6731-6 16 Gallon ESF 2018.qxp_SP6731 2/21/18 8:14 PM Page 6

7

Drum/Caddy Assembly

If any parts are missing or damaged

contact Customer Service.

Do not assemble until you have all the

parts.

1. Invert drum to install caddies.

Install cap nut on one side of shaft

rod. Tap gently with rubber mallet or

hammer until fully seated. Slide open

end of shaft through the wheel

(smooth side of wheel facing outward).

2. Place wheel/shaft assembly through

caddy left and on through the caddy

right, as shown.

3. Then place the remaining wheel onto

the caddy assembly (smooth side of

wheel facing outward), and install

second cap nut.

4. Place the caddy assembly onto the

drum rim. Align inside edges of both

left and right caddies with the raised

outer ribs, located on back of the

drum. Be sure that wheels spin freely,

and do not contact the caddies. If the

wheels do touch the caddies, move

caddies inward slightly.

5. Once the caddies are aligned with the

raised ribs on back of the drum, gently

tap on rear of each caddy until firmly

seated. It is recommended to tap the

center portion of each rear caddy.

After rear portions of caddies are

firmly in place, proceed to tap into

place the front portion of each caddy

until fully seated. It is recommended

to tap the center portion of the front

caddies, as shown.

6. Using a rubber mallet or hammer,

gently tap the wheel caps onto each

wheel until the wheel caps are firmly

seated onto each wheel. This is

required on both left and right sides.

NOTE: Smooth side of

the wheel to the outside.

Caddy

Left

Shaft

Caddy

Right

Wheel

Cap Nut

CADDY ASSEMBLY

Cap Nut

R

I

G

H

T

Raised Rib

on Back of Drum

TAP

Caddy

Wheel

1/16" Clearance

Wheel Cap

Mallet

1/16” (1.6 mm)

Clearance

SP6731-6 16 Gallon ESF 2018.qxp_SP6731 2/21/18 8:14 PM Page 7

Wet/Dry Vac Assembly

1. Position the powerhead assembly on

the drum/caddy assembly as shown

(assembled earlier).

2. Rotate both latches down and press

until you hear them snap over the

flanges on the drum.

Latch

Drum

Latch

Handles

Drum

Latch

Insert Hose

Insert the push button end of the “Dual-

Flex™ Locking” hose into the inlet of the

Vac. The hose should snap into place.

To remove the hose from the Vac, press

the release button in the hose assembly

and pull the hose out of the Vac inlet,

as shown.

Release

Button

Press

and

Pull

7. Insert the caster stem into the socket

of the caster foot as shown.

(Front casters only).

8. Push on the caster until the ball on the

caster stem is inserted all the way into

the socket. You will be able to hear the

ball snap into the socket and the

caster will swivel easily when

positioning is correct.

9. Rotate drum/caddy assembly upright,

using a long phillips screwdriver, install

(8) #10 x 3/4” (19 mm) screws into

matching holes on both right and left

side of caddy. Tighten screws until just

snug. Do not over tighten as this may

tend to deform the caddies.

L

E

F

T

Socket

Caster Stem

Caster Ball

#10 x 3/4"

Screw (8)

Drum/Caddy Assembly (continued)

8

#10 x 3/4” (19 mm)

Screw (8)

SP6731-6 16 Gallon ESF 2018.qxp_SP6731 2/21/18 8:14 PM Page 8

9

Operation

To reduce the risk of electric shock,

this appliance has a polarized plug

(one blade is wider than the other).

This plug will fit in a polarized outlet only

one way. If the plug does not fit fully in

the outlet, reverse the plug. If it still does

not fit, contact a qualified electrician to

install the proper outlet. Do not change

the plug in any way.

After you plug the power cord into the

outlet, turn the unit on by pushing the

switch from position "O" to position "l".

The symbols used on the switch actuator

are international "On & Off" symbols.

Familiarize yourself with the accessories

included with the Vac. Each accessory may

be used in various ways for vacuuming

and blowing debris. Here is a list of the

accessories and their uses.

Utility Nozzle - General purpose nozzle

for most vacuuming applications.

Wet Nozzle - Used for wet pickup on

smooth surfaces to pick up liquid and dry

the surface in one stroke.

Car Nozzle - Dry pickup nozzle for car

interiors and most upholstery cleaning.

Extension Wands - These wands can

be connected together and provides

additional length for more reach.

Dual-Flex™ Locking Hose - Provides

transfer of vacuum or blowing capability

to work site. Provides the means of

attaching extension wands and nozzles.

Crevice Tool - Use to pick up debris in

hard to reach locations.

=OFF =ON

WARNING: To reduce the risk of fire, explosion, or damage to Vac:

• Do not leave Vac running while unattended - you may fail to notice important signs

indicating abnormal operation such as loss of suction, debris/liquid exiting the

exhaust, or abnormal motor noises. Immediately stop using Vac if you notice these

signs.

• Do not leave Vac plugged in when not in use.

• Do not continue running when float has cut off suction.

• Sparks inside the motor can ignite airborne flammables. Do not operate Vac near

flammable liquids or in areas with flammable gases, vapors, or explosive/airborne

dust. Flammable liquids, gases, and vapors include: lighter fluid, solvent-type

cleaners, oil-based paints, gasoline, alcohol, and aerosol sprays. Explosive dusts

include: coal, magnesium, aluminum, grain, and gun powder.

• Do not vacuum up explosive dusts, flammable liquids, or hot ashes.

WARNING: To reduce the risk of electric shock or injury:

• Do not expose to rain or allow liquid to enter motor compartment. Store indoors.

• Do not handle plug, switch, or Vac with wet hands.

• Unplug Vac before servicing. If your Vac is not working as it should, has missing

parts, has been dropped, damaged, left outdoors, or dropped into water, return it to

an authorized service center or call customer service.

• When using an extension cord, use only outdoor-rated cords that are in good

condition. Do not allow the connection to come into contact with liquid.

!

SP6731-6 16 Gallon ESF 2018.qxp_SP6731 2/21/18 8:14 PM Page 9

Operation (continued)

1. The Vac comes equipped with a drain

for easy emptying of liquids. Simply

unscrew the drain cap and lift the

opposite side slightly to empty the

drum.

2. Another option is to remove the

powerhead assembly.

3. Lay powerhead assembly aside on

a clean area while emptying drum.

4. Dump the drum contents into the

proper waste disposal container.

WARNING: To reduce the risk of

back injury or falls, do not lift a Vac

heavy with liquid or debris. Scoop

or drain enough contents out to

make the Vac light enough to lift

comfortably.

Emptying the Drum

Vacuuming Dry Materials

1. The filter must always be in correct

position to reduce the risk of leaks

and possible damage to Vac.

2. Your Wet/Dry Vac comes with the

VF5000 Filter installed. When using

your Vac to pick up very fine dust,

it will be necessary for you to empty

the drum and clean the filter at more

frequent intervals to maintain peak

Vac performance.

NOTE: A dry filter is necessary to pick up

dry material. If you use your Vac to pick

up dust when the filter is wet, the filter will

clog quickly and be very difficult to clean.

Allow filter to dry out before storing.

Vacuuming Liquids

IMPORTANT:

1. When picking up small amounts of

liquid (2-4 inches (5-10 cm) of liquid in

the bottom of the drum) the filter may

be left in place.

2. When picking up larger amounts of

liquid (more than 4 inches (10 cm)

of liquid in the bottom of the drum)

we recommend that the filter be

removed. If the filter is not removed,

it will become saturated and misting

may appear in the exhaust.

3. After using the Vac to pick up liquids,

the filter must be dried to reduce the

risk of possible mildew and damage to

the filter.

4. When the liquid in the drum reaches a

predetermined level, the float

mechanism will rise automatically to cut

off air-flow. When this happens, turn off

the Vac, unplug the power cord, and

empty the drum. You will know that the

float has risen because Vac airflow

ceases and the motor noise will become

higher in pitch, due to increased motor

speed.

Moving the Wet/Dry Vac

Should it become necessary to pic

the Vac up to move it, the handle on

the sides of the dust drum are used to lift.

To maneuver the Vac, the push/pull

handle in the rear of the unit should be

used.

!

10

WARNING: Do not operate

without filter cage and float, as they

prevent liquid from entering the

impeller and damaging the motor.

!

IMPORTANT: To reduce the risk of

damage to the Vac, do not run motor

with float in raised position.

WARNING: To reduce the risk of

injury from accidental starting,

unplug power cord before emptying

the drum.

!

SP6731-6 16 Gallon ESF 2018.qxp_SP6731 2/21/18 8:14 PM Page 10

WARNING: Always wear safety

eyewear complying with ANSI Z87.1

(or in Canada, CSA Z94.3) before

using as a Blower.

CAUTION: Wear a dust mask if

blowing creates dust which might

be inhaled.

CAUTION: To reduce the risk of

hearing damage, wear ear protectors

when using the Vac/Blower for

extended time or in a noisy area.

WARNING: To reduce the risk of

injury to bystanders, keep them

clear of blowing debris.

!

11

Blowing Feature

Your Vac features a blowing port.It can

blow sawdust and other debris.

Follow the steps below to use your

Vac as a blower.

1. Locate blowing port of your Vac.

2. Insert the locking end of the Dual-

Flex™ Locking Hose into the blowing

port of the Vac. The hose should snap

into place. To remove the hose from

the Vac, press the release button in

the hose assembly and pull the hose

out of the Vac inlet.

3. (Optional) Attach extension wand to

opposite end of hose, then place the

car nozzle on the wand.

4. Turn Vac on and you are ready to use

your Vac as a blower.

Car Nozzle (Optional)

Dual-Flex

Locking

Hose

Blowing

Port

Extension

Wand

(Optional)

Swivel

End of

Hose

Operation (continued)

SP6731-6 16 Gallon ESF 2018.qxp_SP6731 2/21/18 8:14 PM Page 11

12

Push/Pull Handle

Cord Wrap

Power

Cord

Cord Wrap

When vacuuming is complete, unplug

the cord and wrap it around the power

assembly as shown. The cord should

wrap under the pull handle (above the

inlet) and around and under the cord

wrap of the motor cover.

Accessory and Hose Storage

Accessory

Storage

Compartment

Accessory Storage

Your accessories may be stored in the

removable tote, or in the two locations on

the caddy right/left.

Hose Storage

Either the hose or the wands may be stored

in the two areas marked Hose Storage.

The hose may be stored by wrapping it

around the unit and plugging the open end

into one of the storage locations on the

caddy assembly. Alternatively, the wands

may also be stored in this location by

plugging either of the ends of the wands

onto the storage receivers located on

the caddy.

Hose Storage

Area

Extension

Wand

Storage

Hose

Storage

Hose

Storage

SP6731-6 16 Gallon ESF 2018.qxp_SP6731 2/21/18 8:14 PM Page 12

13

Maintenance

WARNING: To reduce the risk of

injury from accidental starting,

unplug power cord before changing

or cleaning filter.

NOTE: The filter is made of high quality

paper designed to stop very small

particles of dust. The filter can be used

for dry pick up or small amounts of liquid.

Handle the filter carefully when removing

to clean or installing it. Creases in the

filter pleats may occur from installation

but will not affect the performance of the

filter.

Filter

!

Removal and Installation

of the Qwik Lock™ Filter

Filter Removal:

1. Hold the filter tabs of the Qwik Lock™

filter in each hand.

2. With one thumb on the Qwik Lock™

stud, which protrudes through the

integrated filter plate, lift up on the

filter tabs while pushing down on the

stud.

3. This action will cause the filter to

release from the filter cage. Slide filter

off cage.

IMPORTANT: To avoid damage to the

blower wheel and motor, always reinstall

the filter before using the Vac for dry

material pick-up.

Filter Installation:

1. Carefully slide the Qwik Lock™ filter

over the filter cage and press down on

the outside edge of the filter until the

rubber gasket on the bottom of the

filter seats securely around the base

of the filter cage and against the lid.

2. Align the small center hole in the top

of the filter over the Qwik Lock™ stud

on the filter cage. Press firmly on top

of the filter near the stud to allow the

filter to snap over the ball on the end

of the stud. The filter is now attached.

NOTE: Failure to properly seat the

bottom gasket could result in debris

bypassing the filter.

Filter

Cage

Qwik

Lock™

Stud

Filter

Tabs (2)

Integrated Filter

Plate with Center

Hole

PUSH

DOWN

PULL

UP

Lid

Rubber

Gasket at

Bottom of

Filter

(cutaway

view)

WARNING: Do not operate

without filter cage and float, as they

prevent liquid from entering the

impeller and damaging the motor.

!

SP6731-6 16 Gallon ESF 2018.qxp_SP6731 2/21/18 8:14 PM Page 13

14

Maintenance (continued)

Cleaning and Disinfecting the

Wet/Dry Vac

To keep your Wet/Dry Vac looking its

best, clean the outside with a cloth

dampened with warm water and mild

soap.

To clean the drum:

1. Dump debris out.

2. Wash drum thoroughly with warm

water and mild soap.

3. Wipe out with dry cloth.

Before prolonged storage or as needed

(i.e.; waste water pick up) the drum

should be disinfected.

To disinfect the drum:

1. Pour 1 gallon (4 L) of water and

1 teaspoon (5 mL) chlorine bleach into

the drum.

2. Let solution stand for 20 minutes,

carefully swishing every few minutes,

making sure to wet all inside surfaces

of the drum.

3. Empty drum after 20 minutes. Rinse

with water until bleach smell is gone.

Allow drum to dry completely before

sealing the motor on the drum.

Filter Cleaning

Your filter should be cleaned often to

maintain peak Vac performance.

Cleaning A Dry Filter

1. Some removal of dry debris can be

accomplished without removing the

filter from the Vac. Slap your hand on

top of the lid while the Vac is turned

off.

2. For best cleaning results due to

accumulated dust, clean the filter in

an open area. Cleaning SHOULD be

done outdoors and not in the living

quarters.

3. After filter removal from Vac, remove

the dry debris by gently tapping filter

against the inside wall of your dust

drum. The debris will loosen and fall.

4. For thorough cleaning of dry filter

with fine dust (no debris), run water

through it as described under

"Cleaning A Wet Filter"

Cleaning A Wet Filter

After filter is removed, run water through

the filter from a hose or spigot. Take care

that water pressure from the hose is not

strong enough to damage filter.

IMPORTANT: After cleaning, check the

filter for tears or small holes. Do not use

a filter with holes or tears in it. Even a

small hole can cause a lot of dust to

come out of your Vac. If your filter is

damaged or worn, replace it immediately.

Allow the filter to dry before reinstalling

and storing the Vac or picking up dry

debris.

SP6731-6 16 Gallon ESF 2018.qxp_SP6731 2/21/18 8:14 PM Page 14

15

Maintenance (continued)

Cord Maintenance

When vacuuming is complete, unplug the

cord and wrap it around the motor cover.

If the power cord is damaged, it must be

replaced by the manufacturer or their

service agent or by similarly qualified

personnel to reduce the risk of accident.

Storage

Before storing your Vac, the drum should

be emptied and cleaned. The cord should

be wrapped around the unit and the hose

should be stored as described in this

manual. Accessories should be kept in

the same area as the Vac so they can be

readily available. The Vac should be

stored indoors.

Casters and Wheels

Should your cart squeak or become hard

to roll, you should place two or three

drops of general purpose oil on each

wheel at the axle. If your casters are

noisy, you may put a drop of oil on the

roller shaft to make them quieter.

Frame and Handles

Your metal handle is painted to prevent

rust, however, liquids and corrosive

debris should be wiped off with a soft

cloth should they come in contact with

the handle.

WARNING: To assure product

SAFETY and RELIABILITY, any other

maintenance, repairs and adjustments

should be performed by Authorized

Service Centers, always using RIDGID

replacement parts.

!

Push/Pull Handle

Cord Wrap

Power

Cord

SP6731-6 16 Gallon ESF 2018.qxp_SP6731 2/21/18 8:14 PM Page 15

Key

No. Part No. Description

1 830564 Actuator, Switch (WD19560 Only)

2 813213 Switch, Toggle (WD19560 Only)

2 510553 Switch, Rocker Assembly (WD1956M1 Only)

3 832786 Power Head Assembly (Includes Keys 5 & 6) (WD19560 Only)

4 830847 Lid Latch

5 509488 Float

6 823201-3 Filter Cage

7 VF5000 Qwik Lock™ Fine Dust Filter

8 VT2509 Utility Nozzle

9 VT2503 Car Nozzle

10 VT2510 Wet Nozzle

11 VT2502 Crevice Tool

12 826356-5 Dual-Flex™ Locking Hose

13 VT2508 Extension, Handle

14 SP6731 Owner’s Manual

Repair Parts

16 Gallon / 60 Liter Professional Wet/Dry Vac

Model Numbers WD19560 / WD1956M1

Electrical Ratings:

120 V, 12 A, 60 Hz

RIDGID parts are available on-line at www.RIDGIDparts.com

Always order by Part Number - Not by Key Number

† These replacement parts may be available where you purchased your Vac.

†

16

!WARNING: Unplug before any disassembly or servicing.

!WARNING: All disassembly and repairs should be performed by qualified

personnel.

SP6731-6 16 Gallon ESF 2018.qxp_SP6731 2/21/18 8:14 PM Page 16

16 Gallon / 60 Liter Professional Wet/Dry Vac

Model Numbers WD19560 / WD1956M1

RIDGID parts are available on-line at www.RIDGIDparts.com

10

9

3

2

1

WD19560

8

2

14

11

12

13

7

6

4

5

WD1956M1

WARNING

SERVICING OF DOUBLE-INSULATED WET/DRY VAC

In a double-insulated Wet/Dry Vac, two systems of insulation are provided

instead of grounding. No grounding means is provided on a double-insulated

appliance, nor should a means for grounding be added. Servicing a double-

insulated Wet/Dry Vac requires extreme care and knowledge of the system,

and should be done only by qualified service personnel. Replacement parts

for a double-insulated Wet/Dry Vac must be identical to the parts they replace.

Your double-insulated Wet/Dry Vac is marked with the words "DOUBLE

INSULATED" and the symbol (square within a square) may also be

marked on the appliance.

To reduce the risk of injury from electrical shock, unplug power cord before

servicing the electrical parts of the Wet/Dry Vac.

!

Repair Parts (continued)

17

SP6731-6 16 Gallon ESF 2018.qxp_SP6731 2/21/18 8:14 PM Page 17

Key

No. Part No. Description

1 830858 Handle Assembly

2 830846 Dust Drum Assembly

3 73185 Drain Cap

4 830611 Wheel Cap

5 813836-1 Cap Nut

6 830598 Rear Wheel Assembly (Includes Keys 4 and 5)

7 831024-1 Shaft

8 830841 Caddy, Right

9 830840 Caddy, Left

10 73102 Caster

11 830860-1 Tote

12 820563-4 Screw Type “AB” #10 x 3/4” (19 mm)

13 509748-3 Bag of Loose Parts (Not Illustrated)

(Includes Keys 4, 5, 10, and 12)

18

Repair Parts (continued)

16 Gallon / 60 Liter Professional Wet/Dry Vac Cart

Model Numbers WD19560 / WD1956M1

RIDGID parts are available on-line at www.RIDGIDparts.com

Always order by Part Number - Not by Key Number

!WARNING: Unplug before any disassembly or servicing.

!WARNING: All disassembly and repairs should be performed by qualified

personnel.

SP6731-6 16 Gallon ESF 2018.qxp_SP6731 2/21/18 8:14 PM Page 18

1

11

3

6

7

10

4

5

8

12

7

6

9

10

45

2

Repair Parts (continued)

16 Gallon / 60 Liter Professional Wet/Dry Vac

Model Numbers WD19560 / WD1956M1

RIDGID parts are available on-line at www.RIDGIDparts.com

19

SP6731-6 16 Gallon ESF 2018.qxp_SP6731 2/21/18 8:14 PM Page 19

Part No. SP6731 Form No. SP6731-6 Printed in Mexico 02/18

Stock No. WD1956 / WD1956M

Model No. WD19560 / WD1956M1

Serial Number

Model and serial numbers may be found on the handle. You should record both

model and serial numbers in a safe place for future use.

c 2018 Emerson

• What is covered

RIDGID®Wet/Dry Vacs are warranted to be free of defects in workmanship and material.

• How long coverage lasts

This warranty lasts for the lifetime of the RIDGID®Wet/Dry Vac.

• How to obtain service

To obtain the benefit of this warranty, deliver via prepaid transportation the complete product to

RIDGE TOOL COMPANY, Elyria, Ohio, or any authorized RIDGID® INDEPENDENT SERVICE

CENTER. Pipe wrenches and other hand tools should be returned to the place of purchase.

• What we will do to correct problems

Warranted Wet/Dry Vacs will be repaired or replaced, at Ridge Tool Company's option, and returned

at no charge; or, if after three attempts to repair or replace during the warranty period the Wet/Dry

Vac is still defective, you can elect to receive a full refund of your purchase price.

• What is not covered

Failures due to misuse, abuse or normal wear and tear are not covered by this warranty. RIDGE

TOOL COMPANY SHALL NOT BE RESPONSIBLE FOR ANY INCIDENTAL OR

CONSEQUENTIAL DAMAGES.

• How local laws relate to the warranty

Some states do not allow the exclusion or limitation of incidental or consequential damages, so the

above limitation or exclusion may not apply to you. This warranty gives you specific rights, and you

may also have other rights which vary from state to state, province to province, or country to

country.

• No other express warranty applies

This FULL LIFETIME WARRANTY is the sole and exclusive warranty for RIDGID®Wet/Dry Vacs.

No employee, agent, dealer, or other person is authorized to alter this warranty or make any other

warranty on behalf of Ridge Tool Company.

Symbol of Quality, Durability and

Dependability

FOR QUESTIONS OR INFORMATION CONTACT US AT

1-800-4-RIDGID (1-800-474-3443) from the US and Canada

01-800-701-9811 from Mexico

www.RIDGIDvacs.com

Please have your Model Number and Serial Number on hand when calling

www.RIDGID.com

SP6731-6 16 Gallon ESF 2018.qxp_SP6731 2/21/18 8:14 PM Page 20

La page charge ...

RIDGID WD1956 Le manuel du propriétaire

Ce manuel convient également à

RIDGID WD1956 Le manuel du propriétaire

dans d''autres langues

Documents connexes

Autres documents