VTech DS660V-1F Sky Blue Manuel utilisateur

Catégorie
Téléphones
Taper
Manuel utilisateur
While in a menu, press to select an item, or save an entry
or setting.
4 – OFF/CANCEL
Hang up a call.
Silence the ringer temporarily while the handset is
ringing.
Press and hold to erase the missed call indicator while the
phone is not in use.
Press to return to the previous menu; or press and hold
to return to idle mode, without making changes.
5
Press repeatedly to show other dialing options when
reviewing a caller ID log entry.
6 – MUTE/DELETE
Mute the microphone during a call.
Delete digits or characters while using the dialing keys.
Silence the ringer temporarily while the handset is
ringing.
7 – REDIAL/PAUSE
Press repeatedly to review the redial list.
Press and hold to insert a dialing pause while entering a
number.
8 – Microphone
9
Make or answer a call using the handset speakerphone.
During a call, press to switch between the speakerphone
and the handset.
10 –
Press to add a space when entering names.
11 –
While you have set the dial mode to pulse and on a call,
press to switch to tone dialing temporarily.
12 – 1
Press repeatedly to add or remove 1 in front of the
caller ID log entry before dialing or saving it to the
phonebook.
Press and hold to set or dial your voicemail number.
13 – /HOME/FLASH
Make or answer a home call.
Answer an incoming home call when you hear a call
waiting alert.
14 /CELL
Make or answer a cell call.
Answer an incoming cell call when you hear a call waiting
alert.
15 VOLUME/ /
Review the phonebook when the phone is not in use.
Increase the listening volume during a call.
Scroll up while in a menu, or in the phonebook, caller ID
log, or redial list.
Move the cursor to the right when entering numbers or
names.
VOLUME/ /CID
Review the caller ID log when the phone is not in use.
Decrease the listening volume during a call.
Scroll down while in a menu, or in the phonebook, caller
ID log, or redial list.
Move the cursor to the left when entering numbers or
names.
16 – CHARGE light
On when the handset is charging.
Important safety instructions
When using your telephone equipment, basic safety precautions should always
be followed to reduce the risk of fire, electric shock and injury, including the
following:
1. Read and understand all instructions.
2. Follow all warnings and instructions marked on the product.
3. Unplug this product from the wall outlet before cleaning. Do not use liquid
or aerosol cleaners. Use a damp cloth for cleaning.
4. CAUTION: Do not install the telephone base at a height above 2 meters.
5. Do not use this product near water such as near a bath tub, wash bowl,
kitchen sink, laundry tub or a swimming pool, nor in a wet basement or
shower.
6. Do not place this product on an unstable table, shelf, stand or other unstable
surfaces.
7. Avoid placing the telephone system in places with extreme temperature,
direct sunlight, or other electrical devices. Protect your phone from moisture,
dust, corrosive liquids and fumes.
8. Slots and openings in the back or bottom of the telephone base and handset
are provided for ventilation. To protect them from overheating, these
openings must not be blocked by placing the product on a soft surface
such as a bed, sofa or rug. This product should never be placed near or over
a radiator or heat register. This product should not be placed in any area
where proper ventilation is not provided.
9. This product should be operated only from the type of power source
indicated on the marking label. If you are not sure of the type of power
supply in your home or office, consult your dealer or local power company.
10. Do not allow anything to rest on the power cord. Do not install this product
where the cord may be walked on.
11. Never push objects of any kind into this product through the slots in the
telephone base or handset because they may touch dangerous voltage
points or create a short circuit. Never spill liquid of any kind on the product.
12. To reduce the risk of electric shock, do not disassemble this product, but
take it to an authorized service facility. Opening or removing parts of the
telephone base or handset other than specified access doors may expose
you to dangerous voltages or other risks. Incorrect reassembling can cause
electric shock when the product is subsequently used.
13. Do not overload wall outlets and extension cords.
14. Unplug this product from the wall outlet and refer servicing to an authorized
service facility under the following conditions:
When the power supply cord or plug is damaged or frayed.
If liquid has been spilled onto the product.
If the product has been exposed to rain or water.
If the product does not operate normally by following the operating
instructions. Adjust only those controls that are covered by the operation
instructions. Improper adjustment of other controls may result in damage
and often requires extensive work by an authorized technician to restore
the product to normal operation.
If the product has been dropped and the telephone base and/or
handset has been damaged.
If the product exhibits a distinct change in performance.
Battery installation and charging
Install the battery as shown below. Once you have installed the battery,
you may be able to make and receive short calls. For best performance,
charge the handset battery continuously for at least 12 hours.
1. Plug the battery connector
securely into the socket
inside the handset battery
compartment, matching the
color-coded label.
2. Place the battery with the
label THIS SIDE UP facing
up and the wires inside the
battery compartment.
3. Slide the battery
compartment cover
towards the center of
the handset until it clicks
into place.
4. Place the handset in the telephone
base or charger to charge.
CHARGE light
remains on
when charging.
Electrical outlet
not controlled
by a wall switch
Charger
adapter
Charger installation
Install the charger as shown below.
DS6600 (CA)
DS6600 (US)
15. Avoid using a telephone (other than cordless) during an electrical storm.
There is a remote risk of electric shock from lightning.
16. Do not use the telephone to report a gas leak in the vicinity of the leak.
Under certain circumstances, a spark may be created when the adapter
is plugged into the power outlet, or when the handset is replaced in its
cradle. This is a common event associated with the closing of any electrical
circuit. The user should not plug the phone into a power outlet, and should
not put a charged handset into the cradle, if the phone is located in an
environment containing concentrations of flammable or flame-supporting
gases, unless there is adequate ventilation. A spark in such an environment
could create a fire or explosion. Such environments might include: medical
use of oxygen without adequate ventilation; industrial gases (cleaning
solvents; gasoline vapors; etc.); a leak of natural gas; etc.
17. Only put the handset of your telephone next to your ear when it is in normal
talk mode.
18. The power adapter is intended to be correctly oriented in a vertical or floor
mount position. The prongs are not designed to hold the plug in place if it is
plugged into a ceiling, under-the-table or cabinet outlet.
19. For pluggable equipment, the socket-outlet shall be installed near the
equipment and shall be easily accessible.
20. CAUTION: Use only the batteries indicated in this manual. There
may be a risk of explosion if a wrong type of battery is used. Use only
the supplied rechargeable batteries or replacement batteries (BT183342/
BT283342). Do not dispose of batteries in a fire. They may explode. Dispose
of used battery according to the instruction. Disconnect the telephone line
from the equipment before open the battery door.
Do not use the battery in following conditions:
» High or low extreme temperature during use, storage or
transportation.
» Replacement of a battery with an incorrect type that can defeat a
safeguard.
» Disposal of a battery into fire or a hot oven, or mechanically crushing
or cutting of a battery, that can result in an explosion.
» Leaving a battery in an extremely high temperature surrounding
environment that can result in an explosion or the leakage of
flammable liquid or gas.
» A battery subjected to extremely low air pressure that can result in an
explosion or the leakage of flammable liquid or gas.
21. Use only the adapter included with this product. Incorrect adapter polarity or
voltage can seriously damage the product.
22. The applied nameplate is located at the bottom or near of the product.
SAVE THESE INSTRUCTIONS
Battery
Use only the batteries provided or equivalent. To order a replacement, visit
our website at www.vtechphones.com or call 1 (800) 595-9511. In Canada,
go to phones.vtechcanada.com or call 1 (800) 267-7377.
Do not dispose of the battery in a fire. Check with local waste management
codes for special disposal instructions.
Do not open or mutilate the battery. Released electrolyte is corrosive and
may cause burns or injury to the eyes or skin. The electrolyte may be toxic if
swallowed.
Exercise care in handling batteries in order not to create a short circuit with
conductive materials.
Charge the battery provided with this product only in accordance with the
instructions and limitations specified in this manual.
Precautions for users of implanted cardiac pacemakers
Cardiac pacemakers (applies only to digital cordless telephones):
Wireless Technology Research, LLC (WTR), an independent research entity, led
a multidisciplinary evaluation of the interference between portable wireless
telephones and implanted cardiac pacemakers. Supported by the U.S. Food
and Drug Administration, WTR recommends to physicians that:
Pacemaker patients
Should keep wireless telephones at least six inches from the pacemaker.
Should NOT place wireless telephones directly over the pacemaker, such as
in a breast pocket, when it is turned ON.
Should use the wireless telephone at the ear opposite the pacemaker.
WTR’s evaluation did not identify any risk to bystanders with pacemakers from
other persons using wireless telephones.
About cordless telephones
Privacy: The same features that make a cordless telephone convenient
create some limitations. Telephone calls are transmitted between the
telephone base and the cordless handset by radio waves, so there is a
possibility that the cordless telephone conversations could be intercepted
by radio receiving equipment within range of the cordless handset. For this
reason, you should not think of cordless telephone conversations as being
as private as those on corded telephones.
Electrical power: The telephone base of this cordless telephone must be
connected to a working electrical outlet. The electrical outlet should not be
controlled by a wall switch. Calls cannot be made from the cordless handset
if the telephone base is unplugged, switched off or if the electrical power is
interrupted.
Potential TV interference: Some cordless telephones operate at
frequencies that may cause interference to televisions and VCRs. To
minimize or prevent such interference, do not place the telephone base
of the cordless telephone near or on top of a TV or VCR. If interference is
experienced, moving the cordless telephone farther away from the TV or
VCR often reduces or eliminates the interference.
Rechargeable batteries: Exercise care in handling batteries in order not to
create a short circuit with conducting material such as rings, bracelets and
keys. The battery or conductor may overheat and cause harm. Observe
proper polarity between the battery and the battery charger.
Nickel-metal hydride rechargeable batteries: Dispose of these batteries in
a safe manner. Do not burn or puncture the battery. Like other batteries of
this type, if burned or punctured, they could release caustic material which
could cause injury.
DS6600
DS660V-1F
DS660V-1G
DS660V-1H
DS660V-1J
DECT 6.0 accessory handset
for use with VTech models
DS6611
DS6621
DS662V
User’s manual
Go to www.vtechphones.com (US)
to register your product for enhanced
warranty support and latest VTech
product news.
Go to phones.vtechcanada.com (CA)
for latest VTech product news.
Scan the QR code for
support information
What’s in the box
Your telephone package contains the following items. Save your sales
receipt and original packaging in case it is necessary to ship your
telephone for warranty service.
User’s manual
User’s
manual
Handset
Handset charger and
charger adapter
Battery
Battery charging
Once you have installed the battery, the screen indicates the battery
status (see the table below).
NOTES
For best performance, keep the handset in the telephone base or charger
when not in use.
The battery is fully charged after 12 hours of continuous charging.
If you place the handset in the telephone base or the charger without
plugging in the battery, the screen displays No battery.
Battery indicators Battery status Action
The screen is blank,
or displays Put
in charger and
flashes.
Battery has no or
very little charge.
The handset
cannot be used.
Charge without interruption
(about 30 minutes).
The screen displays
Low battery and
flashes.
Battery has
enough charge to
be used for a short
time.
Charge without interruption
(about 30 minutes).
The screen displays
HANDSET X.
Battery is charged. To keep the battery charged,
place it in the telephone base
or charger when not in use.
When the battery is fully charged, you can expect the following
performance:
Operation Operating time
While in handset use (talking*) Up to seven hours
While in speakerphone mode (talking*) Up to three hours
While not in use (standby**) Up to five days
*Operating times vary depending on your actual use and the age of the
battery.
**Handset is not charging or in use.
After you install your telephone or power returns following a power
outage, the handset will prompt you to set the date and time. To skip
setting the date and time, press OFF/CANCEL.
Add and register a handset
You can add new DS6600/DS660V handsets (purchased separately)
to your DS6611/DS6621/DS662V telephone system. Each handset
must be registered with the telephone base before use. When first
purchased, each handset displays To register HS... and ...see manual
alternately. You may need to charge the handset before registering
it to the telephone base. For more details on battery charging, see
Battery installation and charging section.
To register a handset:
Place the new/non-registered handset in the telephone base. The
handset shows Registering....
The handset shows Registered and you hear a beep when the
registration process completes. The registration process takes about
90 seconds to complete.
Deregister handsets
If you want to replace a handset, or reassign the designated handset
number of a registered handset, you must deregister all handsets
that are registered to the telephone base. Then register each handset
individually.
To make deregistration easier, read all of the instructions on this page
before you begin.
Make sure that all handsets are out of the telephone base and
chargers before you begin deregistration.
To deregister all handsets:
1. Press and hold /FIND HANDSET on the telephone base for about
10 seconds until the IN USE light on the telephone base turns on
and starts flashing.
2. Release /FIND HANDSET and then press it again. You must press
/FIND HANDSET while the IN USE light is still flashing. The IN USE
light flashes for approximately seven seconds.
All handsets show To register HS... and ...see manual alternately
when the deregistration process completes. The deregistration
process takes about 10 seconds to complete.
Operating range
This cordless telephone operates with the maximum power allowed
by the Federal Communications Commission (FCC). Even so, this
handset and telephone base can communicate over only a certain
distance - which can vary with the locations of the telephone base
and handset, the weather, and the layout of your home or office.
When the handset is out of range, the handset displays Out of range
and no pwr at base alternately.
If there is a call while the handset is out of range, it may not ring, or if
it does ring, the call may not connect well when you press /HOME
or /CELL. Move closer to the telephone base, and then press
/HOME or /CELL to answer the call.
If the handset moves out of range during a telephone conversation,
there may be interference. To improve reception, move closer to the
telephone base.
Handset overview
1 – Handset earpiece
2 LCD display
3 – MENU/SELECT
Show the menu.
Battery Pack / Bloc-piles :
(2.4V Ni-MH)
WARNING / AVERTISSEMENT :
DO NOT BURN OR PUNCTURE BATTERIES.
NE PAS INCINÉRER OU PERCER LES PILES.
Made in China / Fabriqué en chine
THIS SIDE UP / CE VERS LE HAUT
CR1232
Battery Pack / Bloc-piles :
(2.4V Ni-MH)
WARNING / AVERTISSEMENT :
DO NOT BURN OR PUNCTURE BATTERIES.
NE PAS INCINÉRER OU PERCER LES PILES.
Made in China / Fabriqué en chine
THIS SIDE UP / CE VERS LE HAUT
Battery Pack / Bloc-piles :
(2.4V Ni-MH)
WARNING / AVERTISSEMENT :
DO NOT BURN OR PUNCTURE BATTERIES.
NE PAS INCINÉRER OU PERCER LES PILES.
Made in China / Fabriqué en chine
THIS SIDE UP / CE VERS LE HAUT
Battery Pack / Bloc-piles :
(2.4V Ni-MH)
WARNING / AVERTISSEMENT :
DO NOT BURN OR PUNCTURE BATTERIES.
NE PAS INCINÉRER OU PERCER LES PILES.
Made in China / Fabriqué en chine
THIS SIDE UP / CE VERS LE HAUT
Battery Pack / Bloc-piles :
(2.4V Ni-MH)
WARNING / AVERTISSEMENT :
DO NOT BURN OR PUNCTURE BATTERIES.
NE PAS INCINÉRER OU PERCER LES PILES.
Made in China / Fabriqué en chine
THIS SIDE UP / CE VERS LE HAUT
Battery Pack / Bloc-piles :
(2.4V Ni-MH)
WARNING / AVERTISSEMENT :
DO NOT BURN OR PUNCTURE BATTERIES.
NE PAS INCINÉRER OU PERCER LES PILES.
Made in China / Fabriqué en chine
THIS SIDE UP / CE VERS LE HAUT
Battery Pack / Bloc-piles :
(2.4V Ni-MH)
WARNING / AVERTISSEMENT :
DO NOT BURN OR PUNCTURE BATTERIES.
NE PAS INCINÉRER OU PERCER LES PILES.
Made in China / Fabriqué en chine
THIS SIDE UP / CE VERS LE HAUT
Battery Pack / Bloc-piles :
(2.4V Ni-MH)
WARNING / AVERTISSEMENT :
DO NOT BURN OR PUNCTURE BATTERIES.
NE PAS INCINÉRER OU PERCER LES PILES.
Made in China / Fabriqué en chine
THIS SIDE UP / CE VERS LE HAUT
Battery Pack / Bloc-piles :
(2.4V Ni-MH)
WARNING / AVERTISSEMENT :
DO NOT BURN OR PUNCTURE BATTERIES.
NE PAS INCINÉRER OU PERCER LES PILES.
Made in China / Fabriqué en chine
THIS SIDE UP / CE VERS LE HAUT
Do not place the
handset in the
charger.
DS6621/DS662V
telephone base
DS6611 telephone
base
a
b
c
d
e
f
g
h
i
j
n
p
o
k
l
m
IMPORTANT!
If you have difficulty with your telephone, please refer to the user’s
manual for a full set of installation and operation instructions. For
customer service, visit our website at www.vtechphones.com or call
1 (800) 595-9511. In Canada, go to phones.vtechcanada.com or call
1 (800) 267-7377.
Need help?
For operations and guides to help you using your
telephone, and for latest information and supports,
go and check the online help topics and online FAQs.
Use your smartphone or mobile device to access our
online help.
Go to https://help.vtechphones.com/DS6600;
OR
Scan the QR code on the right. Launch the camera
app or QR code scanner app on your smartphone
or tablet. Hold the device’s camera up to the QR
code and frame it. Tap the notification to trigger
the redirection of the online help.
- If the QR code is not clearly displayed, adjust
your camera’s focus by moving your device
closer or further away until it is clear.
You can also call our Customer Support at
1 (800) 595-9511 [in US] or
1 (800) 267-7377 [in Canada] for help.
For C-UL compliance only
Mesures de sécurité importantes
Afin de réduire les risques d’incendie, de blessures corporelles ou d’électrocution,
suivez toujours ces mesures préventives de base lorsque vous utilisez votre
téléphone :
1. Lisez et comprenez bien toutes les instructions.
2. Observez toutes les instructions et mises en garde inscrites sur l’appareil.
3. Débranchez ce téléphone de la prise murale avant de le nettoyer. N’utilisez pas
de nettoyeurs liquides ni en aérosol. N’utilisez qu’un chiffon doux et légèrement
humecté.
4. ATTENTION: Ne pas installer le socle téphonique à une hauteur surieure à
2 mètres.
5. N’utilisez pas ce produit près de l’eau, tel que près d’un bain, d’un lavabo, d’un
évier de cuisine, d’un bac de lavage ou d’une piscine, ou dans un sous-sol humide
ou sous la douche.
6. Ne déposez pas ce téléphone sur un chariot, support ou table chancelants.
L’appareil pourrait tomber et être sérieusement endommagé.
7. Évitez d’installer le système téléphonique dans les endroits soumis à une
température extrême, à la lumière directe du soleil ou à proximité immédiate
d’autres appareils électriques ou électroniques. Protégez votre téléphone contre
les sources d’humidité, la poussière, les vapeurs et les liquides corrosifs.
8. Le boîtier de l’appareil est doté de fentes et d’ouvertures d’aération situées
à l’arrière ou en dessous. Afin d’emcher la surchauffe, ces ouvertures ne
doivent pas être obstruées en plant l’appareil sur un lit, divan, tapis ou autre
surface similaires. Ne placez pas cet appareil à proximité d’un ément de
chauffage ni d’une plinthe électrique. De plus, ne l’installez pas dans une unité
murale ou un cabinet fermé qui ne possède pas d’aération aquate.
9. Ne faites fonctionner cet appareil qu’avec le type d’alimentation indiqué sur les
étiquettes de l’appareil. Si vous ne connaissez pas le voltage de votre maison,
consultez votre marchand ou votre fournisseur d’électricité.
10. Ne déposez rien sur le cordon d’alimentation. Installez cet appareil dans un
endroit sécuritaire, là où personne ne pourra trébucher sur la ligne d’alimentation
ni le cordon téléphonique modulaire.
11. N’insérez jamais d’objets à travers les fentes et ouvertures de cet appareil, car
ils pourraient toucher à des points de tension dangereux ou court-circuiter des
pièces, ce qui constituerait un risque d’incendie ou d’électrocution. N’échappez
pas de liquides dans l’appareil.
12. Afin de réduire les risques d’électrocution, ne démontez pas l’appareil, mais
apportez-le plutôt à un centre de service qualifié s’il doit être réparé. En enlevant
le couvercle, vous vous exposez à des tensions dangereuses ou autres dangers
similaires. Un remontage inadéquat peut être à l’origine d’une électrocution
lors d’une utilisation ultérieure de l’appareil. Débranchez l’appareil avant de
proder au nettoyage. Utilisez un chiffon humide et doux.
13. Ne surchargez pas les prises de courant et les rallonges.
14. Débranchez cet appareil de la prise de courant et communiquez avec le
département de service à la clientèle de VTech dans les cas suivants :
Lorsque le cordon d’alimentation est endommagé ou écorché.
Si du liquide a été échappé dans l’appareil.
Si l’appareil a été exposé à une source d’humidité telle que la pluie ou l’eau.
Si le produit ne fonctionne pas normalement en respectant les instructions
de fonctionnement. Réglez uniquement les commandes indiquées dans
le les instructions de fonctionnement. Les réglages incorrects des autres
commandes pourraient provoquer un dommage qui pourrait exiger un travail
exhaustif de la part d’un technicien autorisé afin de rétablir le fonctionnement
normal de l’appareil.
Si le produit a été échappé et que le socle et/ou le combiné a été
endommagé.
Si le produit affiche une nette diminution de sa performance.
15. Évitez d’utiliser un téléphone (autre qu’un sans fil) pendant un orage. Les éclairs
peuvent être à l’origine d’une électrocution.
16. N’utilisez pas le téphone pour rapporter une fuite de gaz à proximité de
la fuite. En certaines circonstances, une flamche pourrait être provoqe
lorsque l’adaptateur est branché à une prise de courant, ou lorsque le combiné
est déposé sur le socle. Ceci est un événement commun associé à la fermeture
d’un circuit électrique. L’utilisateur ne devrait pas brancher le téléphone à une
prise de courant, et ne devrait pas déposer le combiné chargé sur le socle, si le
téléphone se trouve à proximité d’un endroit comportant des concentrations
de gaz inflammables, à moins que la ventilation soit aquate. Une flammèche
dans un tel endroit pourrait provoquer un incendie ou une explosion. De tels
environnements peuvent comprendre: des endroits où l’on utilise de l’oxygène
dical sans ventilation aquate; des gaz industriels (dissolvants de nettoyage,
des vapeurs d’essence, etc.); une fuite de gaz naturel, etc.
17. Ne placez que le combiné de votre téléphone près de votre oreille lorsqu’en
mode de conversation.
18. Ces adaptateurs ont été conçus pour être orientés en position verticale ou montés
au sol. Les broches ne sont pas conçues pour maintenir l’adaptateur en place si
celui-ci est barnché dans une prise au plafond ou sous une table/ armoire.
19. Pour le MATERIEL RACCORDE PAR PRISE DE COURANT, le socle de prise de
courant doit etre installe a proximite du materiel et doit etre aisement accessible.
20. MISE EN GARDE: Il peut y avoir un risque d’explosion si vous
utilisez le mauvais type de piles pour le téléphone. N’utilisez que les piles
rechargeable inclus ou les piles de rechange (BT183342/BT283342). N’incinérez
pas les piles. Celles-ci risqueraient d’exploser. Mettre au rebut les batteries
usagées conformément aux instructions du fabricant. Débrancher les lignes
téléphoniques avant le remplacement des piles.
Évite d’utiliser la batterie dans les conditions suivantes:
» des températures extrêmes faibles ou élevées auxquelles une batterie
peut être soumise pendant l’utilisation, le stockage ou le transport;
» Remplacement d’une batterie par un type incorrect pouvant supprimer
une protection;
» mise au rebut d’une batterie dans un feu ou dans un four chaud, ou
écrasement mécanique ou coupure d’une batterie, susceptible de
provoquer une explosion;
» maintien d’une batterie dans un environnement à très haute température
pouvant provoquer une explosion ou la fuite de liquide ou de gaz
inflammables;
» batterie soumise à une pression de l’air extrêmement faible pouvant
provoquer une explosion ou la fuite de liquide ou de gaz inflammables.
21. N’utilisez que les adaptateurs inclus avec ce produit. L’utilisation d’un adaptateur
dont la polarité ou la tension serait inadéquate risque d’endommager
sérieusement le produit et mettre votre sécurité en péril.
22. La plaque signalétique appliquée est située au bas ou à proximité du produit.
CONSERVEZ CES INSTRUCTIONS
Pile
N’utilisez que la pile incluse ou l’équivalent.
Ne jetez pas la pile au feu. Vérifiez les instructions spécifiques de mise aux rebus
auprès des autorités locales.
N’ouvrez pas et ne mutilez pas la pile. L’électrolyte qui s’en échapperait est
corrosif et pourrait causer des brûlures ou des blessures aux yeux ou à la peau.
L’électrolyte est toxique si avalé.
Soyez prudents lorsque vous manipulez les piles afin d’éviter les courts-circuits
provoqués par des matériaux conducteurs.
Rechargez la pile incluse avec cet appareil, selon les instructions et limites
spécifiées dans ce guide d’utilisation.
Stimulateurs cardiaques implantés dans l’organisme
Les simulateurs cardiaques (s’applique uniquement aux téléphones numériques sans
fil) :
L’organisme ‘Wireless Technology Research, LLC (WTR)’, une firme de recherche
indépendante, a mené une évaluation pluridisciplinaire des interférences entre
les téléphones sans fil portatifs et les stimulateurs cardiaques implantés dans
l’organisme. Appuyée par l’Administration des aliments et drogues (FDA) des États-
Unis, la firme WTR recommande aux médecins :
Avis aux détenteurs de stimulateurs cardiaques
Ils doivent tenir le téléphone sans fil à une distance d’au moins six pouces du
stimulateur cardiaque.
Ils ne doivent PAS placer le téléphone sans fil directement sur le stimulateur
cardiaque, tel que dans une poche de chemise, lorsque celui-ci est en marche.
Ils doivent utiliser le téphone sans fil en l’appuyant sur l’oreille qui se trouve
dans la direction opposée au stimulateur cardiaque.
L’étude effecte par l’organisme WRS n’a pas identifié de risque pour les
détenteurs de simulateurs cardiaques causés par les gens qui utilisent un téphone
sans fil à proximité de ceux-ci.
À propos des téléphones sans fil
Confidentialité : Les mêmes caractéristiques qui constituent des avantages pour les
téléphones sans fil affichent également des restrictions. Les appels téléphoniques
sont transmis entre le combiné sans fil et le socle par le biais d’ondes radio ; il y a
donc la possibilité que vos conversations téphoniques sans fil soient interceptées
par des équipements de réception radio se trouvant dans la pore du combiné
sans fil. Pour cette raison, vous ne devez pas percevoir les communications
téléphoniques sans fil comme étant aussi confidentielles que celles des téléphones
à cordons.
Alimentation électrique : Le socle de ce téléphone sans fil doit être branché à une
prise électrique fonctionnelle. La prise électrique ne doit pas être contrôe par un
interrupteur mural. Les appels ne pourront pas être effectués du combiné sans fil si
le socle est débranché ou mis hors tension ou si le courant est coupé.
Possibilité d’interférences aux téléviseurs : Certains téléphones sans fil fonctionnent
sur des fquences pouvant causer des interrences aux téléviseurs et aux
magnétoscopes. Pour réduire ou prévenir de telles interrences, ne placez pas
le socle du téléphone sans fil près ou sur un téléviseur ou magnétoscope. S’il y a
présence de parasites, il est conseillé d’éloigner le téléphone sans fil du téviseur
ou du magnétoscope afin de réduire possiblement les interrences.
Piles rechargeables : Manipulez les piles avec soin afin de ne pas les court-circuiter
avec des bagues, bracelets ou clés. Les piles ou le conducteur peut surchauffer et
causer des blessures. Respectez la polarité adéquate entre la pile et le chargeur.
Les bloc-piles rechargeables à l’hydrure métallique de nickel : Jetez ces blocs-piles
de manre écologique et sécuritaire. Ne les incirez pas et ne les percez pas. Tel
que les autres piles de ce type, elles pourraient dégager une matière toxique qui
peut causer des blessures corporelles si elles sont brûlées ou percées.
The RBRC seal
The RBRC seal on the Ni-MH battery indicates that VTech
Communications, Inc. is voluntarily participating in an industry program to
collect and recycle these batteries at the end of their useful lives, when
taken out of service within the United States and Canada.
The program provides a convenient alternative to placing used Ni-MH
batteries into the trash or municipal waste, which may be illegal in your
area.
VTech’s participation makes it easy for you to drop off the spent battery at local retailers
participating in the program or at authorized VTech product service centers. Please call
1 (800) 8 BATTERY® for information on Ni-MH battery recycling and disposal bans/
restrictions in your area. VTech’s involvement in this program is part of its commitment to
protecting our environment and conserving natural resources.
The RBRC Seal and 1 (800) 8 BATTERY® are registered trademarks of Call2recycle, Inc.
FCC, ACTA and IC regulations
FCC Part 15
NOTE: This equipment has been tested and found to comply with the requirements
for a Class B digital device under Part 15 of the Federal Communications
Commission (FCC) rules. These requirements are intended to provide reasonable
protection against harmful interference in a residential installation. This equipment
generates, uses and can radiate radio frequency energy and, if not installed and
used in accordance with the instructions, may cause harmful interference to radio
communications. However, there is no guarantee that interference will not occur in
a particular installation. If this equipment does cause harmful interference to radio
or television reception, which can be determined by turning the equipment off and
on, the user is encouraged to try to correct the interference by one or more of the
following measures:
Reorient or relocate the receiving antenna.
Increase the separation between the equipment and receiver.
Connect the equipment into an outlet on a circuit different from that to which the
receiver is connected.
Consult the dealer or an experienced radio/TV technician for help.
WARNING: Changes or modifications to this equipment not expressly approved by
the party responsible for compliance could void the user’s authority to operate the
equipment.
This device complies with Part 15 of the FCC rules. Operation is subject to the
following two conditions: (1) this device may not cause harmful interference, and (2)
this device must accept any interference received, including interference that may
cause undesired operation. Privacy of communications may not be ensured when
using this telephone.
To ensure safety of users, the FCC/ISEDC has established criteria for the amount
of radio frequency energy that can be safely absorbed by a user or bystander
according to the intended usage of the product. This product has been tested
and found to comply with the FCC/ISEDC criteria. The handset may be safely held
against the ear of the user. For body worn operation, this handset has been tested
and meets the FCC/ISEDC RF exposure guidelines when used with the accessories
supplied or designated for this product. Use of other accessories may not ensure
compliance with FCC/ISEDC RF exposure guidelines. The telephone base shall
be installed and used such that parts of the user’s body other than the hands are
maintained at a distance of approximately 20 cm (8 inches) or more.
This Class B digital apparatus complies with Canadian requirement:
CAN ICES-3 (B)/NMB-3(B).
FCC Part 68 and ACTA
This equipment complies with Part 68 of the FCC rules and with technical
requirements adopted by the Administrative Council for Terminal Attachments
(ACTA). The label on the back or bottom of this equipment contains, among other
things, a product identifier in the format US:AAAEQ##TXXXX. This identifier must
be provided to your telephone service provider upon request.
The plug and jack used to connect this equipment to premises wiring and the
telephone network must comply with applicable Part 68 rules and technical
requirements adopted by ACTA. A compliant telephone cord and modular plug is
provided with this product. It is designed to be connected to a compatible modular
jack that is also compliant. An RJ11 jack should normally be used for connecting to a
single line. See the installation instructions in the user’s manual.
The Ringer Equivalence Number (REN) is used to determine how many devices you
may connect to your telephone line and still have them ring when you are called.
The REN for this product is encoded as the 6th and 7th characters following the US:
in the product identifier (e.g., if ## is 03, the REN is 0.3). In most, but not all areas,
the sum of all RENs should be five (5.0) or less. For more information, please contact
your telephone service provider.
This equipment must not be used with Party Lines. If you have specially wired alarm
dialing equipment connected to your telephone line, ensure the connection of this
equipment does not disable your alarm equipment. If you have questions about
what will disable alarm equipment, consult your telephone service provider or a
qualified installer.
If this equipment is malfunctioning, it must be unplugged from the modular jack
until the problem has been corrected. Replacement to this telephone equipment
can only be made by the manufacturer or its authorized agents. For replacement
procedures, follow the instructions outlined under the Limited warranty.
If this equipment is causing harm to the telephone network, the telephone service
provider may temporarily discontinue your telephone service. The telephone
service provider is required to notify you before interrupting service. If advance
notice is not practical, you will be notified as soon as possible. You will be given the
opportunity to correct the problem and the telephone service provider is required
to inform you of your right to file a complaint with the FCC. Your telephone service
provider may make changes in its facilities, equipment, operation, or procedures
that could affect the proper functioning of this product. The telephone service
provider is required to notify you if such changes are planned.
If this product is equipped with a corded or cordless handset, it is hearing aid
compatible.
If this product has memory dialing locations, you may choose to store emergency
telephone numbers (e.g., police, fire, medical) in these locations. If you do store or
test emergency numbers, please:
Remain on the line and briefly explain the reason for the call before hanging up.
Perform such activities in off-peak hours, such as early morning or late evening.
Industry Canada
This device contains licence-exempt transmitter(s)/receiver(s) that comply with
Innovation, Science and Economic Development Canada’s licence-exempt RSS(s).
Operation is subject to the following two conditions:
(1) This device may not cause interference.
(2) This device must accept any interference, including interference that may cause
undesired operation of the device.
Privacy of communications may not be ensured when using this telephone.
The term ‘’IC:‘’ before the certification/registration number only signifies that the
Industry Canada technical specifications were met.
The Ringer Equivalence Number (REN) for this terminal equipment is 0.1. The REN
indicates the maximum number of devices allowed to be connected to a telephone
interface. The termination of an interface may consist of any combination of devices
subject only to the requirement that the sum of the RENs of all the devices not
exceed five.
This product meets the applicable Innovation, Science and Economic Development
Canada technical specifications.
California Energy Commission battery
charging testing instructions
This telephone is set up to comply with the energy-conserving standards right out of the
box. These instructions are intended for California Energy Commission (CEC) compliance
testing only. When the CEC battery charging testing mode is activated, all telephone
functions, except battery charging, will be disabled.
To activate the CEC battery charging testing mode:
1. Unplug the telephone base power adapter from the power outlet. Make sure all
handsets are plugged with charged batteries before proceeding.
2. While you press and hold /FIND HANDSET, plug the telephone base power
adapter back to the power outlet.
3. After about 10 seconds, when the IN USE light starts flashing, release /FIND
HANDSET and then press it again within two seconds. The process takes up to one
minute to complete. When the phone successfully enters the CEC battery charging
testing mode, the IN USE light turns off and all handsets display To register HS...
and ...see manual alternately.
If the phone fails to enter this mode, repeat all the steps mentioned above. The
telephone base will be powered up as normal if you fail to press /FIND HANDSET
within two seconds in Step 3.
To deactivate the CEC battery charging testing mode:
1. Unplug the telephone base power adapter from the power outlet, and then plug
it back in. Then the telephone base is powered up as normal.
2. Place the handset in the telephone base to register it back. The handset displays
Registering... and the red IN USE light on the telephone base turns on. If the
registration is successful, the handset screen displays Registered and beeps. The
handset is registered with the telephone base.
Limited Warranty
What does this limited warranty cover?
The manufacturer of this VTech Product warrants to the holder of a valid proof of
purchase (“Consumer” or “you”) that the Product and all accessories provided in the
sales package (“Product”) are free from defects in material and workmanship, pursuant
to the following terms and conditions, when installed and used normally and in
accordance with the Product operating instructions. This limited warranty extends only
to the Consumer for Products purchased and used in the United States of America and
Canada.
What will VTech do if the Product is not free from defects in materials and
workmanship during the limited warranty period (“Materially Defective Product”)?
During the limited warranty period, VTech’s authorized service representative will
replace at VTech’s option, without charge, a Materially Defective Product. If we replace
the Product, we may use new or refurbished replacement parts. If we choose to replace
the Product, we may replace it with a new or refurbished Product of the same or similar
design. We will retain defective parts, modules, or equipment. Replacement of the
Product, at VTech’s option, is your exclusive remedy. VTech will return the replacement
Products to you in working condition. You should expect the replacement to take
approximately 30 days.
How long is the limited warranty period?
The limited warranty period for the Product extends for ONE (1) YEAR from the date of
purchase. If VTech replaces a Materially Defective Product under the terms of this limited
warranty, this limited warranty also applies to the replacement Product for a period of
either (a) 90 days from the date the replacement Product is shipped to you or (b) the time
remaining on the original one-year warranty; whichever is longer.
What is not covered by this limited warranty?
This limited warranty does not cover:
1. Product that has been subjected to misuse, accident, shipping or other physical
damage, improper installation, abnormal operation or handling, neglect,
inundation, fire, water or other liquid intrusion.
2. Product that has been subjected to contact with liquid, water, rain, extreme
humidity or heavy perspiration, sand, dirt or the like; but then only to the extent
the damage was not caused by incorrectly securing the waterproof handset’s
protective elements, for example, failing to properly close a seal), or such
protective elements are damaged or missing (e.g. a cracked battery door), or
subjecting a Product to conditions beyond its stated specifications or limits (e.g.
30 minutes in 1 meter of fresh water).
3. Product that has been damaged due to repair, alteration or modification by
anyone other than an authorized service representative of VTech;
4. Product to the extent that the problem experienced is caused by signal
conditions, network reliability, or cable or antenna systems;
5. Product to the extent that the problem is caused by use with non-VTech
accessories;
6. Product whose warranty/quality stickers, product serial number plates or
electronic serial numbers have been removed, altered or rendered illegible;
7. Product purchased, used, serviced, or shipped for repair from outside the
United States of America or Canada, or used for commercial or institutional
purposes (including but not limited to Products used for rental purposes);
8. Product returned without a valid proof of purchase (see item 2 below); or
9. Charges for installation or set up, adjustment of customer controls, and
installation or repair of systems outside the unit.
How do you get warranty service?
To obtain warranty service in the United States of America, please visit our website at
www.vtechphones.com or call 1 (800) 595-9511. In Canada, go to
phones.vtechcanada.com or dial 1 (800) 267-7377.
NOTE: Before calling for service, please review the user’s manual - a check of the
Product’s controls and features may save you a service call.
Except as provided by applicable law, you assume the risk of loss or damage during
transit and transportation and are responsible for delivery or handling charges incurred
in the transport of the Product(s) to the service location. VTech will return replaced
Product under this limited warranty. Transportation, delivery or handling charges are
prepaid.
VTech assumes no risk for damage or loss of the Product in transit. If the Product failure
is VTech assumes no risk for damage or loss of the Product in transit. If the Product
failure is not covered by this limited warranty, or proof of purchase does not meet the
terms of this limited warranty, VTech will notify you and will request that you authorize
the cost of replacement prior to any further replacement activity. You must pay for the
cost of replacement and return shipping costs for the replacement of Products that are
not covered by this limited warranty.
What must you return with the Product to get warranty service?
1. Return the entire original package and contents including the Product to the
VTech service location along with a description of the malfunction or difficulty;
and
2. Include a “valid proof of purchase” (sales receipt) identifying the Product
purchased (Product model) and the date of purchase or receipt; and
3. Provide your name, complete and correct mailing address, and telephone
number.
Other limitations
This warranty is the complete and exclusive agreement between you and VTech. It
supersedes all other written or oral communications related to this Product. VTech
provides no other warranties for this Product. The warranty exclusively describes all of
VTech’s responsibilities regarding the Product. There are no other express warranties.
No one is authorized to make modifications to this limited warranty and you should not
rely on any such modification.
State/Provincial Law Rights: This warranty gives you specific legal rights, and you may
also have other rights, which vary from state to state or province to province.
Limitations: Implied warranties, including those of fitness for a particular purpose and
merchantability (an unwritten warranty that the Product is fit for ordinary use) are limited
to one year from the date of purchase. Some states/provinces do not allow limitations
on how long an implied warranty lasts, so the above limitation may not apply to you.
In no event shall VTech be liable for any indirect, special, incidental, consequential, or
similar damages (including, but not limited to lost profits or revenue, inability to use the
Product or other associated equipment, the cost of substitute equipment, and claims
by third parties) resulting from the use of this Product. Some states/provinces do not
allow the exclusion or limitation of incidental or consequential damages, so the above
limitation or exclusion may not apply to you.
Please retain your original sales receipt as proof of purchase
Technical specifications
Transmit frequency DECT frequency: 1921.536-1928.448 MHz
Bluetooth frequency: 2402.000-2480.000 MHz
Channels DECT: 5
Bluetooth: 79
Nominal effective
range
Maximum power allowed by FCC and IC. Actual operating
range may vary according to environmental conditions at the
time of use.
Power requirement
Handset: 2.4V Ni-MH battery
Charger: DC 6V @ 0.4A
Memory Phonebook: 1000 memory locations (shared between home
and cell lines); up to 30 digits and 15 characters
Caller ID log: 50 memory locations;
up to 24 digits and 15 characters
Disclaimer and Limitation of Liability
VTech Communications, Inc. and its suppliers assume no responsibility
for any damage or loss resulting from the use of this user’s manual.
VTech Communications, Inc. and its suppliers assume no responsibility
for any loss or claims by third parties that may arise through the use of
this product.
Company: VTech Communications, Inc.
Address: 9020 SW Washington Square Road - Ste 555 Tigard, OR
97223, United States
Phone: 1 (800) 595-9511 in the U.S. or 1 (800) 267-7377 in Canada
Specifications are subject to change without notice.
© 2022 VTech Communications, Inc.
© 2022 VTech Technologies Canada Ltd
All rights reserved.10/22. DS6600_CIB_US-CAN_V6
DS6600 (US)
DS6600 (CA)
Telephones identified with this logo have reduced noise and
interference when used with most T-coil equipped hearing aids and
cochlear implants. The TIA-1083 Compliant Logo is a trademark of
the Telecommunications Industry Association. Used under license.
T
Compatible with
Hearing Ai
d T-Coil
TIA-1083
  • Page 1 1
  • Page 2 2

VTech DS660V-1F Sky Blue Manuel utilisateur

Catégorie
Téléphones
Taper
Manuel utilisateur

dans d''autres langues