VTech DS667V-2J Marina Blue Manuel utilisateur

Marque: VTech

Modèle: DS667V-2J Marina Blue

Catégorie: Casques mobiles

Taper: Manuel utilisateur

DS6671-2/DS6671-3/DS6671-4/DS6672-4/

DS667V-2F/DS667V-2G/DS667V-2H/

DS667V-2J

DECT 6.0 cordless telephone with

DECT 6.0 cordless headset and

BLUETOOTH® wireless technology

Abridged user’s manual

Introduction

To protect our environment and conserve natural resources, this

Abridged user’s manual provides you with the basic installation and use

instructions. A limited set of features are described in abbreviated form.

Please refer to the online User’s manual for a full set of installation and operation

instructions at www.vtechphones.com.

Before using this VTech product, please read Important safety instructions on

page 13 of this user’s manual.

ECO mode

This power conserving technology reduces power

consumption for optimal battery performance.

The ECO mode activates automatically during calls.

When this mode is on, the handset displays ECO.

Telephones identiﬁed with this logo have reduced noise and

interference when used with most T-coil equipped hearing aids and

cochlear implants. The TIA-1083 Compliant Logo is a trademark of

the Telecommunications Industry Association. Used under license.

ECO

Home 0:00:01

10:15 PM

12/18

ECO

Go to www.vtechphones.com to register your product for enhanced warranty

support and latest VTech product news.

Compatible with

Hearing Aid T-Coil

TIA-1083

Even if you do not subscribe to any conventional telephone service, you

can still use the cell lines alone without plugging in a telephone line cord.

Use only the power adapters and batteries supplied with this product.

To order a replacement, visit our website at www.vtechphones.com or

call 1 (800) 595-9511. In Canada, go to www.vtechcanada.com or call

1 (800) 267-7377.

If you subscribe to telephone service from a cable company or a

VoIP service provider, contact your cable/VoIP service provider for

more information.

•

Parts checklist

Your telephone package contains the following items. Save your sales receipt and

original packaging in the event warranty service is necessary.

Abridged

user’s manual

Telephone base

Handset batteries

(1 for DS6671-2/DS667V-2F/

DS667V-2G/DS667V-2H/

DS667V-2J)

(2 for DS6671-3)

(3 for DS6671-4/DS6672-4)

Handset battery

compartment covers

(1 for DS6671-2/DS667V-2F/

DS667V-2G/DS667V-2H/

DS667V-2J)

(2 for DS6671-3)

(3 for DS6671-4/DS6672-4)

Telephone

line cord

Telephone base

power adapter

Cordless

headset with

an earbud

attached

Ear hooks (3) Additional

earbuds (3)

Head band

Handset charger

and charger

adapter

(1 for DS6671-3)

(2 for DS6671-4/

DS6672-4)

Handsets

(1 for DS6671-2/DS667V-2F/

DS667V-2G/DS667V-2H/

DS667V-2J)

(2 for DS6671-3)

(3 for DS6671-4/DS6672-4)

Ear pad

Telephone base and charger installation

Install the telephone base and charger as shown below.

DSL filter

Click!

Plug!

Click!

Plug!

Battery Pack / Bloc-piles :

(2.4V Ni-MH)

WARNING / AVERTISSEMENT :

DO NOT BURN OR PUNCTURE BATTERIES.

NE PAS INCINÉRER OU PERCER LES PILES.

Made in China / Fabriqué en chine

THIS SIDE UP / CE CÔTÉ VERS LE HAUT

Quick start guide

Quick start

guide

Abridged

user’s manual

Light on!

Battery installation and charging

Install the battery as shown below.

Charge for at least 30 minutes before initial settings.

Charge for 12 hours before initial use.

Battery Pack / Bloc-piles :

(2.4V Ni-MH)

WARNING / AVERTISSEMENT :

DO NOT BURN OR PUNCTURE BATTERIES.

NE PAS INCINÉRER OU PERCER LES PILES.

Made in China / Fabriqué en chine

THIS SIDE UP / CE CÔTÉ VERS LE HAUT

CR1232

Battery Pack / Bloc-piles :

(2.4V Ni-MH)

WARNING / AVERTISSEMENT :

DO NOT BURN OR PUNCTURE BATTERIES.

NE PAS INCINÉRER OU PERCER LES PILES.

Made in China / Fabriqué en chine

THIS SIDE UP / CE CÔTÉ VERS LE HAUT

CR1232

Battery Pack / Bloc-piles :

(2.4V Ni-MH)

WARNING / AVERTISSEMENT :

DO NOT BURN OR PUNCTURE BATTERIES.

NE PAS INCINÉRER OU PERCER LES PILES.

Made in China / Fabriqué en chine

THIS SIDE UP / CE CÔTÉ VERS LE HAUT

CR1232

Battery Pack / Bloc-piles :

(2.4V Ni-MH)

WARNING / AVERTISSEMENT :

DO NOT BURN OR PUNCTURE BATTERIES.

NE PAS INCINÉRER OU PERCER LES PILES.

Made in China / Fabriqué en chine

THIS SIDE UP / CE CÔTÉ VERS LE HAUT

CR1232

IMPORTANT:

Check for a dial tone by pressing /HOME, CELL 1 or CELL 2. If you hear a

dial tone, the installation is successful.

If you do not hear a dial tone:

Make sure the installation procedures described above are properly done.

It may be a wiring problem. If you have changed your telephone service to

digital service from a cable company or a VoIP service provider, the telephone

line may need to be rewired to allow all existing telephone jacks to work.

Contact your cable/VoIP service provider for more information.

•

Headset charging

Charge for 3 hours before initial use.

Plug!

Battery Pack / Bloc-piles :

(2.4V Ni-MH)

WARNING / AVERTISSEMENT :

DO NOT BURN OR PUNCTURE BATTERIES.

NE PAS INCINÉRER OU PERCER LES PILES.

Made in China / Fabriqué en chine

THIS SIDE UP / CE CÔTÉ VERS LE HAUT

CR1232

Battery Pack / Bloc-piles :

(2.4V Ni-MH)

WARNING / AVERTISSEMENT :

DO NOT BURN OR PUNCTURE BATTERIES.

NE PAS INCINÉRER OU PERCER LES PILES.

Made in China / Fabriqué en chine

THIS SIDE UP / CE CÔTÉ VERS LE HAUT

CR1232

Click!

Light on!

Telephone base overview

X/DELETE

/SKIP

/PLAY/STOP

/REPEAT

CELL 2

Message window

IN USE

light

FIND HANDSET

ANS ON

/VOL

CELL 1

Handset overview

VOLUME/ /CID

/HOME/FLASH

MUTE/DELETE

CHARGE light

Dialing keys

VOLUME/ /

MENU/SELECT

OFF/CANCEL

REDIAL/PAUSE

CELL 1

HOLD

/auA

CELL 2

PUSH TO TALK

Headset overview

MUTE/FLASH

RESET recessed button

Rotating clip

On/Off

Volume/+/-

Earpiece

Microphone

To attach the earbud to the headset earpiece:

Choose an appropriate earbud.

Press the earbud towards the earpiece until it clicks into place. Move the earbud

around so that the protruding bump on the earbud is pointing towards your

mouth when placed on your ear. The protruding bump on the earbud holds the

headset securely in your ear.

Headset attachments

Earbud

To remove the earbud from the headset earpiece:

Hold both sides of the earbud and then pull the earbud until it separates from

the earpiece.

1. Hold the headset with one hand.

Lift the ear hook upward. 2. Twist the ear hook 180 o clockwise.

3. Push the ear hook downward. 4. Hook the headset on your left ear.

Adjust the angle of the headset until the

microphone is pointing towards

your mouth

Ear hook

To attach the ear hook to the headset:

Remove any headset attachment (earbud excluded) connected to the headset.

Insert the ear hook [A] into the rotating clip [B] on the headset until it clicks

into place.

Hook the headset on your right ear. Adjust the angle of the headset until the

microphone is pointing towards your mouth. Firmly grip the earpiece with one

hand whenever adjusting the headset microphone up or down.

To adjust the headset to wear on your left ear:

Protruding bump

[A] [B]

Bluetooth

To use a Bluetooth enabled cell phone with your DS6671/DS6672/DS667V, you

must ﬁrst pair and connect your Bluetooth cell phone(s) with the telephone base. All

DS6671/DS6672/DS667V handsets can be used to make or answer calls on the

cell lines.

Bluetooth wireless technology operates within a short range (a maximum of

approximately 30 feet). When you pair a Bluetooth cell phone to the telephone

base, place your Bluetooth cell phone closer to the telephone base to maintain

sufﬁcient signal strength. For optimal performance, keep your cell phone within

15 feet of the telephone base while using the cell line.

Pair and connect your first Bluetooth cell phone

Press and hold CELL 1/CELL 2 on the telephone base for about four

seconds. You hear a tone and the CELL 1/CELL 2 light blinks.

Turn on the Bluetooth feature of your cell phone. Once your cell phone ﬁnds

your VTech phone (VTech DS6671/VTech DS6672/VTech DS667V), press the

appropriate key on your cell phone to continue the pairing process.

Your cell phone may prompt you to enter the PIN of the telephone base. The

default PIN of the telephone base is 0000.

•

To remove the head band from the headset:

Hold the headset with one hand and the head band with

your other hand.

Pull the end of the head band until it separates from the

rotating clip on the headset.

Headband

To attach the head band to the headset:

>%@

>$@

To wear on your left ear, hold the headset with one hand and the head band with

your other hand. Rotate the head band within the rotating clip on the headset.

•

Attach the ear pad to the headset

earpiece.

To wear the headset on your right ear,

insert the end [A] of the head band into

the rotating clip [B] on the headset until

it clicks into place.

Remove any headset attachment

connected to the headset.

Adjust the head band to ﬁt your

head. Adjust and rotate the angle of

the headset until the microphone is

pointing towards your mouth. Firmly

grip the earpiece with one hand

whenever adjusting the headset

microphone up or down.

To remove the ear hook from the headset:

Hold the headset with one hand and the ear hook with your

other hand.

Pull the end of the ear hook up until it separates from the

rotating clip on the headset.

VTech Connect to CellTM application

This application helps you integrate your Android phones with

your DS6671/DS6672/DS667V.

For more information and application download,

go to http://www.vtechphones.com/app_connect_to_cell

Cell ringer

When you pair an iPhone (with iOS4.1 or above) to your DS6671/DS6672/

DS667V, the DS6671/DS6672/DS667V handsets play your iPhone’s ringer when

you receive a call on your iPhone.

Press MENU when the phone is not in use.

Scroll to Bluetooth >> Press SELECT.

Scroll to Cell ringer >> Press SELECT.

Scroll to choose On or Off >> Press SELECT.

Download phonebook

Press MENU when the phone is not in use.

Scroll to Bluetooth >> Press SELECT.

Scroll to Download PB >> Press SELECT.

Scroll to select the desired cell phone >> Press SELECT.

For Android cell phones, you may also download

your cell phone directory to your DS6671/DS6672/DS667V

via the VTech Contact Share application.

Go to http://www.vtechphones.com/app_contact_share

for application download.

Using the handset menu

Press MENU when the phone is not in use.

Press

until the screen displays the desired

feature menu.

Press SELECT to enter that menu.

To return to the previous menu, press CANCEL.

To return to idle mode, press and hold CANCEL.

Telephone settings

Default settings are indicated by asterisks(*).

Settings menu Description Options

LCD language Set the screen display language. English*;

Français;

Español

Voicemail # Set the voicemail number for speed dial. Voicemail #

Clr voicemail Turn off the voicemail indicators (see the

note below). Reset Voicemail

Indicator?

Key tone Set the volume of the audible beep whenever

a key is pressed, or turn it off. Level 1; 2*; 3;

Off

CID time sync Set to synchronize the time in the caller ID log. On*;

Off

Dial mode Set the telephone to be touch-tone or

pulse dialing. Touch-tone*;

Pulse

Use the Clr voicemail feature when the telephone indicates there is new voicemail

but there is none. For example, when you have accessed your voicemail while away

from home. The Clr voicemail feature only turns off the indicators; it does not delete

your voicemail messages. As long as you have new voicemail messages, your

telephone service provider continues to send the signal that turns on the indicators.

The following are some of the telephone features you may wish to set. Refer to

Telephone settings in the online User’s manual for detailed instructions for

setting all telephone features.

Set date and time

If you subscribe to caller ID service, the day, month and time are set automatically

with each incoming call. You can also set the date and time manually.

Press MENU when the handset is not in use.

Scroll toto Set date/time >> Press SELECT.

Enter the month, date and year >> Press SELECT.

Enter the hour and minute.

Scroll to choose AM or PM >> Press SELECT.

•

Ringer volume

You can adjust the ringer volume level, or turn the ringer off.

Press MENU when the handset is not in use.

Scroll to Ringers >> Press SELECT twice.

Scroll to adjust the volume >> Press SELECT.

If the handset ringer volume is set to off, that handset is silenced for all incoming

calls except paging tone.

Quiet mode

You can turn on the quiet mode for a period of time. During this period, all tones

(except paging tone) and call screening are muted. When you turn on the quiet

mode, the answering system turns on automatically.

Press and hold when the handset is not in use.

Use the dialing keys (0-9) to enter the duration >> Press SELECT to save.

To turn off the quiet mode, press and hold when the handset is not in use.

Telephone operation

Make a home call

Press /HOME or and then dial the telephone number.

Press on the headset to join the call. Hang up the handset

at any time to leave the call and the headset continues

the call.

Make a cell call

Press CELL 1 or CELL 2.

Enter the telephone number >> Press the corresponding CELL key to dial.

Press on the headset to join the call. Hang up the handset at any time to leave

the call and the headset continues the call.

While using the cell line, place your cell phone closer to the telephone base, and

make sure that there are no physical obstacles between the telephone base and the

cell phone, such as large furniture or thick walls.

Answer a home/cell call

Press /HOME, CELL 1/ CELL 2, or any dialing key.

Press on the headset.

End a home/cell call

Press OFF on the handset or put the handset to the telephone base or charger.

Press on the headset or put the headset back on the base.

Speakerphone

During a call, press to switch between the speakerphone and handset earpiece.

Volume

During a call, press VOLUME/ or VOLUME/ on the handset, or +/-/volume

on the side of the headset to adjust the listening volume.

The headset, handset earpiece and speakerphone volume settings are independent.

Mute

The mute function allows you to hear the other party but the

other party cannot hear you.

During a call, press MUTE. The handset displays Muted.

Press MUTE again to resume the conversation.

Call waiting

When you subscribe to call waiting service from your telephone service provider,

you hear an alert tone if there is an incoming call while you are on another call.

For a home call, press FLASH to put the current call on hold and take the new

call, or switch back and forth between calls.

For a cell call, press CELL 1/ CELL 2 to put the current call on hold and

take the new call, or switch back and forth between calls.

Temporary ringer silencing

When the telephone is ringing, you can temporarily silence the ringer of the handset

without disconnecting the call. The next call rings normally at the preset volume.

Press OFF, MUTE or on the handset. displays and Ringer muted

displays brieﬂy.

Press /VOL on the telephone base.

Press MUTE on the headset.

•

Find handset

Use this feature to ﬁnd all system handsets and headset.

To start paging:

Press FIND HANDSET on the telephone base. All idle handsets ring and

display ** Paging **. The headset rings and blinks in blue.

To end paging:

Press FIND HANDSET again on the telephone base.

Press /HOME, , CANCEL or any dialing key on the handset.

Place the handset in the telephone base or charger.

Press on the headset.

Do not press and hold FIND HANDSET for more than four seconds. It may lead

to deregistration.

Redial list

Each handset stores the last 10 telephone numbers dialed.

To review and dial a number from the redial list:

Press REDIAL when the phone is not in use.

Press , oror REDIAL repeatedly until the desired entry displays.

Press /HOME, CELL 1 or CELL 2 to dial.

To delete a redial entry:

When the desired redial entry displays, press DELETE.

Join a call in progress

You can use up to four system handsets at a time. You can buy additional expansion

handsets (DS6071/DS607V) for this telephone base. You can register up to twelve

devices to the telephone base, including a maximum of two cordless headsets.

When a handset is on a call, press /HOME or the corresponding CELL

key on another handset to join the call. Press OFF to exit the call. The call

continues until all devices hang up.

Press on the headset to join the call. Press again to exit the call. The callThe call

continues until all devices hang up.

Push-to-talk (PTT)

You can directly broadcast messages from one handset to the speakerphone of

one or multiple handsets.

To start a PTT communication:

Press PUSH TO TALK when the phone is not in use.

Scroll to a desired handset oror Group >> Press SELECT.

Only one handset can talk at a time.

Press and hold PUSH TO TALK while you are talking.

Release PUSH TO TALK to let the other party respond.

Intercom

Use the intercom feature for conversations between two handsets.

Press MENU on your handset when not in use.

Scroll to Intercom >> Press SELECT >> Scroll to the destination handset

number >> Press SELECT.

To answer the intercom call, press /HOME, CELL 1/ CELL 2, or any

dialing keys on the destination handset.

To end the intercom call, press OFF or place the handset back in the telephone

base or charger.

Answer an incoming call during an intercom call

If you receive an incoming call during an intercom call, there is an alert tone.

To answer a home call, press /HOME. The intercom call ends automatically.

To end the intercom call without answering the outside call, press OFF. The

intercom call ends and the telephone continues to ring.

To answer a cell call, press CELL 1/ CELL 2. The intercom call endshe intercom call ends

automatically.

Phonebook

Your phone has three phonebooks, one home phonebook and two cell

phonebooks, which are shared by all system handsets. The home phonebook

stores up to 200 contacts and each cell phonebook stores up to 1000 contacts.

To add a directory entry to the home phonebook:

Press MENU when the phone is not in use.

Scroll to Phonebook >> Press SELECT twice.

Scroll to Add contact >> Press SELECT.

Enter the number >> Press SELECT to move to the name.

Enter the name. Additional key presses show other characters of that

particular key.

•

Press SELECT to save.

While entering numbers and names, you can:

Press DELETE to erase a digit or character.

Press and hold DELETE to erase the entire entry.

Press or to move the cursor to the left or right.

Press and hold PAUSE to insert a dialing pause (for entering phone numbers only).

Press /auA to switch the character between upper and lower case (for

entering names only).

Press 0 to add a space (for entering names only).

To review and dial from the phonebook:

Entries are sorted alphabetically.

Press MENU when the phone is not in use.

Scroll to Phonebook >> Press SELECT.

Scroll to the desired phonebook >> Press SELECT twice.

Scroll to browse through the phonebook, or start a name search.

When the desired entry appears, press /HOME, CELL 1 or CELL 2

to dial.

To delete a phonebook entry:

When the desired entry displays, press DELETE.

When the handset displays Delete contact?, press SELECT.

To remove an entire cell phonebook:

Press MENU when the phone is not in use.

Scroll to Phonebook >> Press SELECT.

Scroll to the desired phonebook >> Press SELECT.

Scroll to Remove PB >> Press SELECT.

When the handset displays Remove PB?, press SELECT.

Caller ID

This product supports caller ID services provided by most telephone service

providers. Depending on your service subscription, you may see the caller’s name,

number, date and time of calls that are sent by your telephone service provider after

the ﬁrst or second ring.

Caller ID log

The caller ID log stores up to 50 entries. If you answer a call before the caller

information appears, it will not be saved in the caller ID log.

The handset displays XX Missed calls when there are calls that have not been

reviewed in the caller ID log.

If you want to erase the missed call indicator, press and hold CANCEL on the

idle handset.

To review and dial a number in the caller ID log:

Press CID when the phone is not in use.

Scroll to browse through the caller ID log. When the desired entry appears:

Press repeatedly to show different dialing options.

Press 1 repeatedly if you need to add or remove 1 in front of the phone number.

Press /HOME, CELL 1 or CELL 2 to dial the displayed number.

To save a caller ID log entry to the home phonebook:

When the desired caller ID log entry displays, press SELECT.

Modify the number when necessary >> Press SELECT.

Modify the name when necessary >> Press SELECT to save.

To delete a caller ID log entry:

When the desired caller ID log entry displays, press DELETE.

To delete all caller ID log entries:

Press MENU when the phone is not in use.

Scroll to Caller ID log >> Press SELECT.

Scroll to Del all calls >> Press SELECT twice.

About answering system and voicemail

Your telephone has separate indicators for two different types of voice messages:

those left on the built-in answering system and those left at your telephone service

provider’s voicemail. Each alerts you to new messages differently.

If XX new messages displays on the handset and the message window on

the telephone base ﬂashes, there are messages recorded on the built-in

answering system. It can record up to 99 messages, depending on the length of

each message. Each message can be up to three minutes in length. The total

recording time is approximately 14 minutes.

If and New voicemail display on the handset, your telephone service

provider is indicating that it has new voicemail for you. Contact your telephone

service provider for more information on how to access your voicemail.

•

Answering system settings

Default settings are indicated by asterisks (*).

Settings menu Description Options

Call screening Set whether you hear the callers while they are

leaving messages to you. On*;

Off

# of rings Set the number of times the telephone rings

before the answering system answers. 4*; 3; 2;

Toll saver; 6; 5

Remote code Set a two-digit security code to access the

answering system remotely from any touch-tone

telephone.

19*

Msg alert tone Set to alert you when you have new messages. Off*;

Recording time Set the recording time for each incoming message. 3 minutes*;

2 minutes;

1 minute

Set number of rings

You can set the answering system to answer an incoming call after 2, 3, 4, 5 or 6 rings;

or toll saver. If you choose toll saver, the answering system answers a call after 2 rings

when you have new messages, or after 4 rings when you have no new messages.

Press MENU when the phone is not in use.

Scroll to Answering sys >> Press SELECT.

Scroll to Ans sys setup >> Press SELECT.

Scroll to # of rings >> Press SELECT.

Scroll to choose 2, 3, 4, 5, 6 or Toll saver >> Press SELECT.

Record your own announcement

You can use the preset announcement to answer calls, or replace it with your own

recorded announcement. It can be up to 90 seconds in length.

Press MENU when the phone is not in use.

Scroll to Answering sys >> Press SELECT three times.

The handset announces, “Record after the tone. Press 5 when you are done.”

After the tone, speak towards the handset microphone. Press 5 when done.

Answering system operation

Turn the answering system on or off

The answering system must be turned on to answer and record messages.

Press ANS ON on the telephone base to turn the built-in answering system

on or off.

Message playback at the telephone base

Press /PLAY when the phone is not in use.

Options during playback:

Press q/VOL or p/VOL to adjust the speaker volume.

Press /SKIP to skip to the next message.

Press /REPEAT to repeat the playing message. Press /REPEAT twice to

listen to the previous message.

Press X/DELETE to delete the playing message. The system advances to the

next message.

Press /STOP to stop.

Delete all messages at the telephone base

Press X/DELETE twice when the phone is not in use.

Call intercept

If you want to talk to the person whose message is being recorded, press /HOME

or on the handset, or press on the headset.

Expand your telephone system

You can add new handsets (DS6071/DS607V, purchased separately) and new

headset (IS6100, purchased separately) to your telephone system. This telephone

system accommodates up to 12 devices, including a maximum of two headsets.

For more details, refer to the user’s manual that comes with your DS6071/DS607V

new handset and IS6100 new headset respectively.

•

Troubleshooting

If you have difﬁculty with your telephone, please try the suggestions below. For customer service,For customer service,

visit our website at www.vtechphones.com or call 1 (800) 595-9511.

In Canada, go to www.vtechcanada.com or call 1 (800) 267-7377.

I cannot add and connect my cell phone to the telephone base.

Make sure you have cellular coverage.

Make sure your cell phone is compatible with your DS6671/DS6672/DS667V. Check the Bluetooth

compatibility list at www.vtechphones.com.

Make sure the Bluetooth function of your cell phone is turned on. See the user’s manual of your cell

phone for more information.

Make sure that your Bluetooth cell phone is not connected to any other Bluetooth device.

To connect your cell phone, make sure that your cell phone is connected and active on the device list.

Remove VTech DS6671/VTech DS6672/VTech DS667V from your cell phone’s handsfree device

history list (see the user’s manual of your cell phone for more information).

Carefully follow the pairing instructions on page 6 and make sure that your cell phone is not

connected to any other Bluetooth device.

Turn off your cell phone, then turn it on again.

For some cell phones, you must authorize VTech DS6671/VTech DS6672/VTech DS667V

device in your cell phone’s Bluetooth feature. See the user’s manual of your cell phone for more

information.

Manually connect your cell phone to VTech DS6671/VTech DS6672/VTech DS667V. Refer to the

user’s manual of your cell phone for more information.

Reset the telephone base. Unplug the unit’s electrical power. Wait for approximately 15 seconds,

then plug it back in. Repeat the above suggestions.

The PIN on the telephone base does not work.

Make sure you enter the correct PIN. The default PIN is 0000.

My telephone does not work at all.

Make sure the battery is installed and charged correctly. For optimum daily performance, return the

handset to the telephone base or charger after use.

Make sure the power adapter is securely plugged into an outlet not controlled by a wall switch.

Make sure the telephone line cord is plugged ﬁrmly into the telephone base and the wall jack.

Unplug the electrical power to the telephone base. Wait for approximately 15 seconds, then plug

it back in. Allow up to one minute for the cordless handset and telephone base to synchronize.

Charge the battery in the handset for up to 12 hours.

If the battery is completely depleted, charge the handset for at least 30 minutes before use.

Remove the battery and then install it again. If that still does not work, it may be necessary to

purchase a new battery.

Disconnect the telephone base from the telephone wall jack and plug in a working telephone. If the

other telephone does not work, the problem is probably in the wiring or telephone service. Contact

your telephone service provider.

If you have changed your telephone service to digital service from a cable company or a VoIP

service provider, the telephone line may need to be rewired to allow all existing telephone jacks to

work. Contact your service provider for more information.

The display shows No line. I cannot hear the dial tone.

Disconnect the telephone line cord from your telephone and connect it to another telephone. If

there is no dial tone on that other telephone either, then the telephone line cord may be defective.

Try installing a new telephone line cord.

If changing telephone line cord does not help, the wall jack (or the wiring to this wall jack) may be

defective. Contact your telephone service provider.

You may be using a new cable or VoIP service, the existing telephone jacks in your home may no

longer work. Contact your service provider for solutions.

The display shows To register HS, see manual. The handset does not work at all.

The handset is deregistered from the telephone base. Place the handset in the telephone base

to register it back. The handset shows HANDSET X Registered and you hear a beep when the

registration process completes. This process takes about 90 seconds to complete.

The light on the headset flashes slowly and alternately in red and blue. The headset does

not work at all.

The headset is deregistered from the telephone base. Follow the instructions below to register the

headset back to the telephone base.

1. Press and hold FIND HANDSET on the telephone for about four seconds until the red

IN USE light turns on.

2. Immediately place the headset in the telephone base. The red IN USE light on the telephone

base turns off.

The light on the headset turns red when it is registered but not fully charged, or turns blue if it

is registered and fully charged. This process takes about 60 seconds to complete.

The answering system does not record messages.

Make sure the answering system is on.

Make sure the memory of the answering system is not full. When the answering machine memory

is full, it does not record new messages until some old messages are deleted.

If you subscribe to voicemail service, change the number of rings so that your answering system

answers before your voicemail answers. To determine how many rings activate your voicemail,

contact your telephone service provider.

If there is a fax machine connected to the same telephone line, try disconnecting the fax machine.

If that solves the problem, consult your fax machine documentation for information on compatibility

with answering systems.

I accidentally changed the LCD language to French or Spanish, and I don’t know how to

change it back to English.

Press MENU, then enter 364 to reset the LCD language to English.

Common cure for electronic equipment.

If the telephone is not responding normally, put the cordless handset in the telephone base. If this

does not ﬁx the problem, do the following (in the order listed):

1. Disconnect the power to the telephone base.

2. Disconnect the battery on the cordless handset.

3. Wait a few minutes before connecting power to the telephone base.

4. Install the battery again and place the cordless handset in the telephone base .

5. Wait for the cordless handset to synchronize with the telephone base. Allow up one minute for

this to take place.

•

Important safety instructions

When using your telephone equipment, basic safety precautions should always be followed to reduce the

risk of ﬁre, electric shock and injury, including the following:

Read and understand all instructions.

Follow all warnings and instructions marked on the product.

Unplug this product from the wall outlet before cleaning. Do not use liquid or aerosol cleaners. Use a

damp cloth for cleaning.

Do not use this product near water such as near a bath tub, wash bowl, kitchen sink, laundry tub or

swimming pool, or in a wet basement or shower.

Do not place this product on an unstable table, shelf, stand or other unstable surfaces.

Avoid placing the telephone system in places with extreme temperature, direct sunlight, or other

electrical devices. Protect your phone from moisture, dust, corrosive liquids and fumes.

Slots and openings in the back or bottom of the telephone base and handset are provided for ventilation.

To protect them from overheating, these openings must not be blocked by placing the product on a soft

surface such as a bed, sofa or rug. This product should never be placed near or over a radiator or heat

This product should be operated only from the type of power source indicated on the marking label. If you are

not sure of the type of power supply in your home or ofﬁce, consult your dealer or local power company.

Do not allow anything to rest on the power cord. Do not install this product where the cord may be

walked on.

Never push objects of any kind into this product through the slots in the telephone base or handset

because they may touch dangerous voltage points or create a short circuit. Never spill liquid of any

kind on the product.

To reduce the risk of electric shock, do not disassemble this product, but take it to an authorized

service facility. Opening or removing parts of the telephone base or handset other than speciﬁed

access doors may expose you to dangerous voltages or other risks. Incorrect reassembling can

cause electric shock when the product is subsequently used.

Do not overload wall outlets and extension cords.

Unplug this product from the wall outlet and refer servicing to an authorized service facility under the

following conditions:

When the power supply cord or plug is damaged or frayed.

If liquid has been spilled onto the product.

If the product has been exposed to rain or water.

If the product does not operate normally by following the operating instructions. Adjust only those controls

that are covered by the operation instructions. Improper adjustment of other controls may result in damage

and often requires extensive work by an authorized technician to restore the product to normal operation.

If the product has been dropped and the telephone base and/or handset has been damaged.

If the product exhibits a distinct change in performance.

14. Avoid using a telephone (other than cordless) during an electrical storm. There is a remote risk of

electric shock from lightning.

15. Do not use the telephone to report a gas leak in the vicinity of the leak. Under certain circumstances,

a spark may be created when the adapter is plugged into the power outlet, or when the handset is

replaced in its cradle. This is a common event associated with the closing of any electrical circuit.

The user should not plug the phone into a power outlet, and should not put a charged handset into

the cradle, if the phone is located in an environment containing concentrations of ﬂammable or

ﬂame-supporting gases, unless there is adequate ventilation. A spark in such an environment could

create a ﬁre or explosion. Such environments might include: medical use of oxygen without adequate

ventilation; industrial gases (cleaning solvents; gasoline vapors; etc.); a leak of natural gas; etc.

16. Only put the handset of your telephone next to your ear when it is in normal talk mode.

17. The power adapters are intended to be correctly oriented in a vertical or ﬂoor mount position. The prongs

are not designed to hold the plug in place if it is plugged into a ceiling, under-the-table or cabinet outlet.

18. For pluggable equipment, the socket-outlet shall be installed near the equipment and shall be easily

accessible.

SAVE THESE INSTRUCTIONS

Battery

CAUTION: Use Only Supplied Battery.

Do not dispose of the battery in a fire. Check with local waste management codes for special disposal instructions.

Do not open or mutilate the battery. Released electrolyte is corrosive and may cause burns or injury to the

eyes or skin. The electrolyte may be toxic if swallowed.

Exercise care in handling batteries in order not to create a short circuit with conductive materials.

Charge the battery provided with this product only in accordance with the instructions and limitations

specified in this manual.

Precautions for users of implanted cardiac pacemakers

Cardiac pacemakers (applies only to digital cordless telephones):

Wireless Technology Research, LLC (WTR), an independent research entity, led a multidisciplinary evaluation

of the interference between portable wireless telephones and implanted cardiac pacemakers. Supported by

the U.S. Food and Drug Administration, WTR recommends to physicians that:

Pacemaker patients

Should keep wireless telephones at least six inches from the pacemaker.

Should NOT place wireless telephones directly over the pacemaker, such as in a breast pocket, when it

is turned ON.

Should use the wireless telephone at the ear opposite the pacemaker. WTR’s evaluation did not identify

any risk to bystanders with pacemakers from other persons using wireless telephones.

WTR’s evaluation did not identify any risk to bystanders with pacemakers from other persons using

wireless telephones.

Operating range

This cordless telephone operates with the maximum power allowed by the Federal Communications Commission

(FCC). Even so, this handset and telephone base can communicate over only a certain distance - which can vary

with the locations of the telephone base and handset, the weather, and the layout of your home or ofﬁce.

When the handset is out of range, the handset displays Out of range OR Base no power.

If there is a call while the handset is out of range, it may not ring, or if it does ring, the call may not connect

well when you press /HOME. Move closer to the telephone base, then press /HOME to answer the call.

If the handset moves out of range during a telephone conversation, there may be interference. To improve

reception, move closer to the telephone base.

10.

11.

12.

13.

•

Maintenance

Taking care of your telephone

Your cordless telephone contains sophisticated electronic parts, so it must be treated with care.

Avoid rough treatment

Place the handset down gently. Save the original packing materials to protect your telephone if you ever need

to ship it.

Avoid water

Your telephone can be damaged if it gets wet. Do not use the handset outdoors in the rain, or handle it with

wet hands. Do not install the telephone base near a sink, bathtub or shower.

Electrical storms

Electrical storms can sometimes cause power surges harmful to electronic equipment. For your own safety,

take caution when using electrical appliances during storms.

Cleaning your telephone

Your telephone has a durable plastic casing that should retain its luster for many years. Clean it only with a soft

cloth slightly dampened with water or mild soap. Do not use excess water or cleaning solvents of any kind.

The RBRC® seal

The RBRC® seal on the nickel-metal hydride battery indicates that VTech Communications, Inc. is

voluntarily participating in an industry program to collect and recycle these batteries at the end of their

useful lives, when taken out of service within the United States and Canada.

The RBRC® program provides a convenient alternative to placing used nickel-metal hydride batteries

into the trash or municipal waste, which may be illegal in your area.

VTech’s participation in RBRC® makes it easy for you to drop off the spent battery at local retailers

participating in the RBRC® program or at authorized VTech product service centers. Please call 1

(800) 8 BATTERY® for information on Ni-MH battery recycling and disposal bans/restrictions in your

area. VTech’s involvement in this program is part of its commitment to protecting our environment

and conserving natural resources.

RBRC® and 1 (800) 8 BATTERY® are registered trademarks of the Rechargeable Battery

Recycling Corporation.

FCC, ACTA and IC regulations

FCC Part 15

NOTE: This equipment has been tested and found to comply with the requirements for a Class B digital device

under Part 15 of the Federal Communications Commission (FCC) rules. These requirements are intended to provide

reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can

radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful

interference to radio communications. However, there is no guarantee that interference will not occur in a particular

installation. If this equipment does cause harmful interference to radio or television reception, which can be determined

by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the

following measures:

Reorient or relocate the receiving antenna.

Increase the separation between the equipment and receiver.

Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.

Consult the dealer or an experienced radio/TV technician for help.

WARNING: Changes or modiﬁcations to this equipment not expressly approved by the party responsible for

compliance could void the user’s authority to operate the equipment.

This device complies with Part 15 of the FCC rules. Operation is subject to the following two conditions:

(1) this device may not cause harmful interference, and (2) this device must accept any interference received, including

interference that may cause undesired operation. Privacy of communications may not be ensured when using this telephone.

To ensure safety of users, the FCC has established criteria for the amount of radio frequency energy that can be safely

absorbed by a user or bystander according to the intended usage of the product. This product has been tested and

found to comply with the FCC criteria. The handset may be safely held against the ear of the user. The telephone base

shall be installed and used such that parts of the user’s body other than the hands are maintained at a distance of

approximately 20 cm (8 inches) or more.

This Class B digital apparatus complies with Canadian requirement:

CAN ICES-3 (B)/NMB-3(B)

FCC Part 68 and ACTA

This equipment complies with Part 68 of the FCC rules and with technical requirements adopted by the Administrative

Council for Terminal Attachments (ACTA). The label on the back or bottom of this equipment contains, among other

things, a product identiﬁer in the format US:AAAEQ##TXXXX. This identiﬁer must be provided to your telephone

service provider upon request.

The plug and jack used to connect this equipment to premises wiring and the telephone network must comply with

applicable Part 68 rules and technical requirements adopted by ACTA. A compliant telephone cord and modular plug

is provided with this product. It is designed to be connected to a compatible modular jack that is also compliant. An

RJ11 jack should normally be used for connecting to a single line and an RJ14 jack for two lines. See the installation

instructions in the user’s manual.

The Ringer Equivalence Number (REN) is used to determine how many devices you may connect to your telephone

line and still have them ring when you are called. The REN for this product is encoded as the 6th and 7th characters

following the US: in the product identiﬁer (e.g., if ## is 03, the REN is 0.3). In most, but not all areas, the sum of all

RENs should be ﬁve (5.0) or less. For more information, please contact your telephone service provider.

This equipment may not be used with Party Lines. If you have specially wired alarm dialing equipment connected

to your telephone line, ensure the connection of this equipment does not disable your alarm equipment. If you have

questions about what will disable alarm equipment, consult your telephone service provider or a qualiﬁed installer.

If this equipment is malfunctioning, it must be unplugged from the modular jack until the problem has been corrected.

Repairs to this telephone equipment can only be made by the manufacturer or its authorized agents. For repair

procedures, follow the instructions outlined under the Limited warranty.

If this equipment is causing harm to the telephone network, the telephone service provider may temporarily discontinue

your telephone service. The telephone service provider is required to notify you before interrupting service. If advance

notice is not practical, you will be notiﬁed as soon as possible. You will be given the opportunity to correct the problem

and the telephone service provider is required to inform you of your right to ﬁle a complaint with the FCC. Your

telephone service provider may make changes in its facilities, equipment, operation, or procedures that could affect the

proper functioning of this product. The telephone service provider is required to notify you if such changes are planned.

If this product is equipped with a corded or cordless handset, it is hearing aid compatible.

If this product has memory dialing locations, you may choose to store emergency telephone numbers

(e.g., police, ﬁre, medical) in these locations. If you do store or test emergency numbers, please:

Remain on the line and brieﬂy explain the reason for the call before hanging up.

Perform such activities in off-peak hours, such as early morning or late evening.

Industry Canada

This device complies with Industry Canada licence-exempt RSS standard(s).

Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this

device must accept any interference received, including interference that may cause undesired operation.

Privacy of communications may not be ensured when using this telephone.

The term ‘’IC:‘’ before the certiﬁcation/registration number only signiﬁes that the Industry Canada technical

speciﬁcations were met.

The Ringer Equivalence Number (REN) for this terminal equipment is 1.0. The REN indicates the maximum number of

devices allowed to be connected to a telephone interface. The termination of an interface may consist of any combination

of devices subject only to the requirement that the sum of the RENs of all the devices does not exceed ﬁve.

This product meets the applicable Innovation, Science and Economic Development Canada technical speciﬁcations.

•

Remember that electrical appliances can cause serious injury if used when you are wet or standing in water. If

the telephone base should fall into water, DO NOT RETRIEVE IT UNTIL YOU UNPLUG THE POWER CORD

AND TELEPHONE LINE CORD FROM THE WALL. Then remove the telephone by the unplugged cords.

For C-UL compliance only

Mesures de sécurité importantes

Aﬁn de réduire les risques d’incendie, de blessures corporelles ou d’électrocution, suivez toujours ces mesures

préventives de base lorsque vous utilisez votre téléphone :

Lisez et comprenez bien toutes les instructions.

Observez toutes les instructions et mises en garde inscrites sur l’appareil.

Débranchez ce téléphone de la prise murale avant de le nettoyer. N’utilisez pas de nettoyeurs liquides ni en

aérosol. N’utilisez qu’un chiffon doux et légèrement humecté.

N’utilisez pas ce produit près de l’eau, tel que près d’un bain, d’un lavabo, d’un évier de cuisine, d’un bac de

lavage ou d’une piscine, ou dans un sous-sol humide ou sous la douche.

Ne déposez pas ce téléphone sur un chariot, support ou table chancelants. L’appareil pourrait tomber et être

sérieusement endommagé.

Évitez d’installer le système téléphonique dans les endroits soumis à une température extrême, à la lumière

directe du soleil ou à proximité immédiate d’autres appareils électriques ou électroniques. Protégez votre

téléphone contre les sources d’humidité, la poussière, les vapeurs et les liquides corrosifs.

Le boîtier de l’appareil est doté de fentes et d’ouvertures d’aération situées à l’arrière ou en dessous. Aﬁn

d’empêcher la surchauffe, ces ouvertures ne doivent pas être obstruées en plaçant l’appareil sur un lit, divan,

tapis ou autre surface similaires. Ne placez pas cet appareil à proximité d’un élément de chauffage ni d’une

plinthe électrique. De plus, ne l’installez pas dans une unité murale ou un cabinet fermé qui ne possède pas

d’aération adéquate.

Ne faites fonctionner cet appareil qu’avec le type d’alimentation indiqué sur les étiquettes de l’appareil. Si vous ne

connaissez pas le voltage de votre maison, consultez votre marchand ou votre fournisseur d’électricité.

Ne déposez rien sur le cordon d’alimentation. Installez cet appareil dans un endroit sécuritaire, là où personne

ne pourra trébucher sur la ligne d’alimentation ni le cordon téléphonique modulaire.

N’insérez jamais d’objets à travers les fentes et ouvertures de cet appareil, car ils pourraient toucher à

des points de tension dangereux ou court-circuiter des pièces, ce qui constituerait un risque d’incendie ou

d’électrocution. N’échappez pas de liquides dans l’appareil.

Aﬁn de réduire les risques d’électrocution, ne démontez pas l’appareil, mais apportez-le plutôt à un centre de

service qualiﬁé s’il doit être réparé. En enlevant le couvercle, vous vous exposez à des tensions dangereuses ou

autres dangers similaires. Un remontage inadéquat peut être à l’origine d’une électrocution lors d’une utilisation

ultérieure de l’appareil. Débranchez l’appareil avant de procéder au nettoyage. Utilisez un chiffon humide et

doux.

Ne surchargez pas les prises de courant et les rallonges.

Débranchez cet appareil de la prise de courant et communiquez avec le département de service à la clientèle

de VTech dans les cas suivants:

Lorsque le cordon d’alimentation est endommagé ou écorché.

Si du liquide a été échappé dans l’appareil.

Si l’appareil a été exposé à une source d’humidité telle que la pluie ou l’eau.

Si le produit ne fonctionne pas normalement en respectant les instructions de fonctionnement. Réglez

uniquement les commandes indiquées dans le les instructions de fonctionnement. Les réglages incorrects

des autres commandes pourraient provoquer un dommage qui pourrait exiger un travail exhaustif de la

part d’un technicien autorisé aﬁn de rétablir le fonctionnement normal de l’appareil.

Si le produit a été échappé et que le socle et/ou le combiné a été endommagé.

Si le produit afﬁche une nette diminution de sa performance.

14. Évitez d’utiliser un téléphone (autre qu’un sans ﬁl) pendant un orage. Les éclairs peuvent être à l’origine d’une

électrocution.

15. N’utilisez pas le téléphone pour rapporter une fuite de gaz à proximité de la fuite. En certaines circonstances,

une ﬂammèche pourrait être provoquée lorsque l’adaptateur est branché à une prise de courant, ou lorsque

le combiné est déposé sur le socle. Ceci est un événement commun associé à la fermeture d’un circuit

électrique. L’utilisateur ne devrait pas brancher le téléphone à une prise de courant, et ne devrait pas

déposer le combiné chargé sur le socle, si le téléphone se trouve à proximité d’un endroit comportant des

concentrations de gaz inﬂammables, à moins que la ventilation soit adéquate. Une ﬂammèche dans un tel

endroit pourrait provoquer un incendie ou une explosion. De tels environnements peuvent comprendre: des

endroits où l’on utilise de l’oxygène médical sans ventilation adéquate; des gaz industriels (dissolvants de

nettoyage, des vapeurs d’essence, etc.); une fuite de gaz naturel, etc.

16. Ne placez que le combiné de votre téléphone près de votre oreille lorsqu’en mode de conversation.

17. Ces adaptateurs ont été conçus pour être orientés en position verticale ou montés au sol. Les broches ne

sont pas conçues pour maintenir l’adaptateur en place si celui-ci est barnché dans une prise au plafond ou

sous une table/ armoire.

18. Pour le MATERIEL RACCORDE PAR PRISE DE COURANT, le socle de prise de courant doit etre installe a

proximite du materiel et doit etre aisement accessible.

CONSERVEZ CES INSTRUCTIONS

Pile

MISE EN GARDE : Risque d’explosion si la pile est remplacée par une pile de types incorrects. Jetez les piles

épuisées en respectant les instructions.

Ne jetez pas la pile au feu. Vérifiez les instructions spécifiques de mise aux rebus aupr

s des autorités locales.

N’ouvrez pas et ne mutilez pas la pile. L’électrolyte qui s’en échapperait est corrosif et pourrait causer des brûlures

ou des blessures aux yeux ou à la peau. L’électrolyte est toxique si avalé.

Soyez prudents lorsque vous manipulez les piles afin d’éviter les courts-circuits provoqués par des matériaux

conducteurs.

Rechargez la pile incluse avec cet appareil, selon les instructions et limites spécifiées dans ce guide d’utilisation.

Stimulateurs cardiaques implantés dans l’organisme

Les simulateurs cardiaques (s’applique uniquement aux téléphones numériques sans fil):

L’organisme ‘Wireless Technology Research, LLC (WTR)’, une firme de recherche indépendante, a mené une

évaluation pluridisciplinaire des interférences entre les téléphones sans fil portatifs et les stimulateurs cardiaques

implantés dans l’organisme. Appuyée par l’Administration des aliments et drogues (FDA) des États-Unis, la firme WTR

recommande aux médecins:

Avis aux détenteurs de stimulateurs cardiaques

Ils doivent tenir le téléphone sans fil à une distance d’au moins six pouces du stimulateur cardiaque.

Ils ne doivent PAS placer le téléphone sans fil directement sur le stimulateur cardiaque, tel que dans une poche de

chemise, lorsque celui-ci est en marche.

Ils doivent utiliser le téléphone sans fil en l’appuyant sur l’oreille qui se trouve dans la direction opposée au

stimulateur cardiaque.

L’étude effectuée par l’organisme WRS n’a pas identifié de risque pour les détenteurs de simulateurs cardiaques

causés par les gens qui utilisent un téléphone sans fil à proximité de ceux-ci.

À propos des téléphones sans fil

Alimentation électrique: Les mêmes caractéristiques qui constituent des avantages pour les téléphones sans fil

affichent également des restrictions. Les appels téléphoniques sont transmis entre le combiné sans fil et le socle par

le biais d’ondes radio ; il y a donc la possibilité que vos conversations téléphoniques sans fil soient interceptées par

des équipements de réception radio se trouvant dans la portée du combiné sans fil. Pour cette raison, vous ne devez

pas percevoir les communications téléphoniques sans fil comme étant aussi confidentielles.

Alimentation électrique: Le socle de ce téléphone sans fil doit être branché à une prise électrique fonctionnelle.

La prise électrique ne doit pas être contrôlée par un interrupteur mural. Les appels ne pourront pas être effectués

du combiné sans fil si le socle est débranché ou mis hors tension ou si le courant est coupé.

Possibilité d’interférences aux téléviseurs: Certains téléphones sans fil fonctionnent sur des fréquences pouvant

causer des interférences aux téléviseurs et aux magnétoscopes. Pour réduire ou prévenir de telles interférences, ne

placez pas le socle du téléphone sans fil près ou sur un téléviseur ou magnétoscope. S’il y a présence de parasites,

il est conseillé d’éloigner le téléphone sans fil du téléviseur ou du magnétoscope afin de réduire possiblement les

interférences.

Piles rechargeables: Manipulez les piles avec soin afin de ne pas les court-circuiter avec des bagues, bracelets

ou clés. Les piles ou le conducteur peut surchauffer et causer des blessures. Respectez la polarité adéquate entre

la pile et le chargeur.

Les bloc-piles rechargeables à l’hydrure métallique de nickel: Jetez ces blocs-piles de manière écologique et

sécuritaire. Ne les incinérez pas et ne les percez pas. Tel que les autres piles de ce type, elles pourraient dégager

une matière toxique qui peut causer des blessures corporelles si elles sont brûlées ou percées.

Limited warranty

What does this limited warranty cover?

The manufacturer of this VTech Product warrants to the holder of a valid proof of purchase (“Consumer” or “you”)

that the Product and all accessories provided in the sales package (“Product”) are free from defects in material and

workmanship, pursuant to the following terms and conditions, when installed and used normally and in accordance with

10.

11.

12.

13.

•

the Product operating instructions. This limited warranty extends only to the Consumer for Products purchased and

used in the United States of America and Canada.

What will VTech do if the Product is not free from defects in materials and workmanship during the limited

warranty period (“Materially Defective Product”)?

During the limited warranty period, VTech’s authorized service representative will repair or replace at VTech’s option,

without charge, a Materially Defective Product. If we repair the Product, we may use new or refurbished replacement

parts. If we choose to replace the Product, we may replace it with a new or refurbished Product of the same or similar

design. We will retain defective parts, modules, or equipment. Repair or replacement of the Product, at VTech’s option,

is your exclusive remedy. VTech will return the repaired or replacement Products to you in working condition. You

should expect the repair or replacement to take approximately 30 days.

How long is the limited warranty period?

The limited warranty period for the Product extends for ONE (1) YEAR from the date of purchase. If VTech repairs or

replaces a Materially Defective Product under the terms of this limited warranty, this limited warranty also applies to the

repaired or replacement Product for a period of either (a) 90 days from the date the repaired or replacement Product is

shipped to you or (b) the time remaining on the original one-year warranty; whichever is longer.

What is not covered by this limited warranty?

This limited warranty does not cover:

Product that has been subjected to misuse, accident, shipping or other physical damage, improper installation,

abnormal operation or handling, neglect, inundation, ﬁre, water or other liquid intrusion; or

Product that has been damaged due to repair, alteration or modiﬁcation by anyone other than an authorized

service representative of VTech; or

Product to the extent that the problem experienced is caused by signal conditions, network reliability, or cable or

antenna systems; or

Product to the extent that the problem is caused by use with non-VTech accessories; or

Product whose warranty/quality stickers, product serial number plates or electronic serial numbers have been

removed, altered or rendered illegible; or

Product purchased, used, serviced, or shipped for repair from outside the United States of America or Canada, or

used for commercial or institutional purposes (including but not limited to Products used for rental purposes); or

Product returned without a valid proof of purchase (see item 2 below); or

Charges for installation or set up, adjustment of customer controls, and installation or repair of systems outside the unit.

How do you get warranty service?

To obtain warranty service in the USA, please visit our website at www.vtechphones.com or call

1 (800) 595-9511. In Canada, go to www.vtechcanada.com or call 1 (800) 267-7377.

NOTE: Before calling for service, please review the user’s manual - a check of the Product’s controls and features may

save you a service call.

Except as provided by applicable law, you assume the risk of loss or damage during transit and transportation and are

responsible for delivery or handling charges incurred in the transport of the Product(s) to the service location. VTech will return

repaired or replaced Product under this limited warranty. Transportation, delivery or handling charges are prepaid. VTech

assumes no risk for damage or loss of the Product in transit. If the Product failure is not covered by this limited warranty, or

proof of purchase does not meet the terms of this limited warranty, VTech will notify you and will request that you authorize the

cost of repair prior to any further repair activity. You must pay for the cost of repair and return shipping costs for the repair of

Products that are not covered by this limited warranty.

What must you return with the Product to get warranty service?

Return the entire original package and contents including the Product to the VTech service location along with a

description of the malfunction or difﬁculty; and

Include a “valid proof of purchase” (sales receipt) identifying the Product purchased (Product model) and the date

of purchase or receipt; and

Provide your name, complete and correct mailing address, and telephone number.

Other limitations

This warranty is the complete and exclusive agreement between you and VTech. It supersedes all other written or oral

communications related to this Product. VTech provides no other warranties for this Product. The warranty exclusively

describes all of VTech’s responsibilities regarding the Product. There are no other express warranties.

No one is authorized to make modiﬁcations to this limited warranty and you should not rely on any such modiﬁcation.

State/Provincial Law Rights: This warranty gives you speciﬁc legal rights, and you may also have other rights, which

vary from state to state or province to province.

Limitations: Implied warranties, including those of ﬁtness for a particular purpose and merchantability (an unwritten

warranty that the Product is ﬁt for ordinary use) are limited to one year from the date of purchase. Some states/provinces

do not allow limitations on how long an implied warranty lasts, so the above limitation may not apply to you. In no event

shall VTech be liable for any indirect, special, incidental, consequential, or similar damages (including, but not limited

to lost proﬁts or revenue, inability to use the Product or other associated equipment, the cost of substitute equipment,

and claims by third parties) resulting from the use of this Product. Some states/provinces do not allow the exclusion or

limitation of incidental or consequential damages, so the above limitation or exclusion may not apply to you.

Please retain your original sales receipt as proof of purchase.

Technical Specifications

Frequency control Crystal controlled PLL synthesizer

Transmit frequency DECT frequency: 1921.536-1928.448 MHz

Bluetooth frequency: 2402.000-2480.000 MHz

Channels DECT: 5

Bluetooth: 79

Nominal effective range Maximum power allowed by FCC and IC. Actual operating

range may vary according to environment conditions at the

time of use.

Power requirements Handset: 2.4V Ni-MH battery

Telephone base: Output #1: 6V DC @ 450mA;;

Output #2: 6V DC @ 300mA

Charger: 6V AC @ 300mA

Memory Home phonebook:

200 memory locations; up to 30 digits and 15 characters

Cell phonebooks:

1000 memory locations (each); up to 30 digits and 15 characters

Caller ID log:

50 memory locations; up to 24 digits and 15 characters

The Bluetooth® word mark and logos are owned by Bluetooth SIG, Inc. and any use of such

marks by VTech Holdings Limited is under license. VTech Holdings Limited is a member of

Bluetooth SIG, Inc. Other trademarks and trade names are those of their respective owners.

Speciﬁcation are subject to change without notice.

Document order number: 91-006681-070-100

VTech DS667V-2J Marina Blue Manuel utilisateur

Marque: VTech

Modèle: DS667V-2J Marina Blue

Catégorie: Casques mobiles

Taper: Manuel utilisateur

Télécharger le PDF

rapport

dans d''autres langues

English: VTech DS667V-2J Marina Blue User manual

VTech DS667V-2J Marina Blue Manuel utilisateur

VTech DS667V-2J Marina Blue Manuel utilisateur

dans d''autres langues

Documents connexes