Troy-Bilt TROY-BILT 34B2C Battery Powered Brushless Zero Turn Tractor Manuel utilisateur

Safe Operation Practices • Assembly • Operation • Service And Maintenance

OperatOr’s Manual

Form No. 769-26628A

(January 24, 2023)

Battery-Powered Lithium-Ion Zero-Turn

Tractor

Lapbar Steering & Drive Controls

NOTE: This Operator’s Manual covers several models. Features may vary by model. Not all features in this manual are

applicable to all models and the model depicted may differ from yours.

WARNING

Read and follow all safety rules and instructions in this manual before attempting to operate this

machine.

Failure to comply with these instructions may result in personal injury - SAVE THESE INSTRUCTIONS.

WARNING

CALIFORNIA PROPOSITION 65

Cancer and Reproductive Harm – www.P65Warnings.ca.gov.

Record Product Information

Before setting up and operating your

new tractor, please locate the model

plate on the equipment and record

the information in the provided

area to the right. You can locate the

model plate by lifting up the seat

and looking under the seat pan. This

information will be necessary, should

you seek technical support via our

web site, Customer Support, or with a

local authorized service center.

Model Number

3 4 B 2 C

Serial Number

English ......................................................................................................................................Page 2

Spanish (Español) ....................................................................................................................Page 30

French (Français) ...................................................................................................................... Page 59

2

SAFE OPERATION PRACTICES

GENERAL INFORMATION

1. Read, understand, and follow all instructions on the tractor

and in the manual(s) before attempting to assemble and

operate. Keep this manual in a safe place for future and

regular reference and for ordering replacement parts.

2. Be familiar with all controls and their proper operation. Know

how to stop the tractor and disengage them quickly.

3. Never allow children under 14 years of age to operate this

tractor. Children 14 and over should read and understand

the instructions and safe operation practices in this manual

and on the tractor and should be trained and supervised by

an adult.

4. Never allow adults to operate this tractor without proper

instruction.

5. If situations occur which are not covered in this manual, use

care and good judgment. Contact your customer service

representative for assistance.

6. According to the U.S. Consumer Products Safety Commission

(CPSC) and the U.S. Environmental Protection Agency (EPA),

this product has an estimated useful life of seven (7) years,

under ordinary use conditions. At the end of its useful life,

have the product inspected annually to ensure all mechanical

and safety systems are operating properly, safely, and are

not worn excessively. Failure to do so may result in accident,

injury, or death.

PREPARATION BEFORE OPERATING

1. Thoroughly inspect the area where the tractor is to be used.

Remove all stones, sticks, wire, bones, toys, and other foreign

objects which could be tripped over or picked up and thrown

by the blade(s). Thrown objects can cause serious personal

injury.

2. To help avoid blade contact or a thrown object injury, keep

bystanders, helpers, children and pets at least 75 feet

(23 meters) from the tractor while it is in operation. Keep

bystanders, children and pets inside during operation. Stop

tractor if anyone enters the area.

3. Be aware of the tractor discharge direction and do not point

it at anyone.

4. Always wear safety glasses or safety goggles during

operation and while performing an adjustment or repair to

protect your eyes. Thrown objects which ricochet can cause

serious injury to the eyes.

5. Wear sturdy, rough-soled work shoes and close-fitting slacks

and shirts. Loose fitting clothes, jewelry and long hair can be

caught in movable parts. Never operate this tractor in bare

feet or sandals.

6. Do not charge or operate the tractor in the rain or wet

conditions.

7. Use only accessories and attachments approved for this

tractor by the tractor manufacturer. Read, understand and

follow all instructions provided with the approved accessory

or attachment.

OPERATING

1. Data indicates that operators, age 65 years and above, are

involved in a large percentage of tractor-related injuries.

These operators should evaluate their ability to operate the

tractor safely enough to protect themselves and others from

serious injury.

2. Set the parking brake before attempting to start the tractor.

3. Plan your mowing pattern to avoid discharge of material

toward roads, sidewalks, bystanders and the like. Also, avoid

discharging material against a wall or obstruction which

may cause discharged material to ricochet back toward the

operator.

WARNING

This symbol points out important safety instructions which, if not followed, could endanger the personal

safety and/or property of yourself and others. Read and follow all instructions in this manual before

attempting to operate this tractor. Failure to comply with these instructions may result in personal injury.

When you see this symbol, HEED ITS WARNING!

DANGER

This tractor was built to be operated according to the safe operation practices in this manual. As with any type of

power equipment, carelessness or error on the part of the operator can result in serious injury. This tractor is capable of

amputating fingers, hands, toes and feet and throwing debris. Failure to observe the following safety instructions could

result in serious injury or death.

Lithium-Ion Battery System

Servicing requires extreme care and knowledge of the system and must be performed only by a qualified service

technician. For repair or service take the tractor to your nearest authorized service dealer. Always use original

equipment manufacturer’s (OEM) replacement parts when servicing.

3

SAFE OPERATION PRACTICES

4. In case of a system fault or a complete loss of battery power,

the tractor on a hill can freewheel. Depress the brake pedal

to maintain control and stop the tractor. Restart the tractor.

If the system fault problem persists, contact your authorized

service dealer.

5. Do not put hands or feet near rotating parts or under the

cutting deck. Contact with the blade(s) can amputate hands

and feet.

6. Watch for holes, ruts, bumps, rocks, or other hidden objects.

Uneven terrain could overturn the tractor. Tall grass can hide

obstacles.

7. Check overhead clearances carefully before driving under

low hanging tree branches, wires, door openings etc., where

the operator may be struck or pulled from the tractor, which

could result in serious injury.

8. Never leave a running tractor unattended. Always turn off

blade(s), set parking brake, press Start/Stop button, and

remove key before dismounting.

9. Turn off blade(s), set parking brake, press Start/Stop button

and wait until the blade(s) come to a complete stop before

removing grass catcher, emptying grass, unclogging chute,

removing any grass or debris, or making any adjustments.

10. Your tractor is designed to cut normal residential grass of a

height no more than 10” (25.4 cm). Do not attempt to mow

through unusually tall, dry grass (e.g., pasture) or piles of

dry leaves. Dry grass or leaves may contact hot surfaces and/

or build up on the tractor deck presenting a potential fire

hazard.

11. Turn off blade(s) before traveling in reverse. Back up slowly.

Always look down and behind before and while backing to

avoid a back-over accident.

12. Never carry passengers.

13. Stay at least 10 feet (3 meters) from drop-offs, ditches,

embankments or the edge of water. The tractor could

suddenly turn over if a wheel is over the edge of a cliff, ditch,

or if an edge caves in.

14. A missing or damaged chute deflector, mulch plug or entire

grass catcher can cause blade contact or thrown object

injuries.

15. Do not operate the tractor without the chute deflector, mulch

plug or entire grass catcher in its proper place.

16. Use extra care with grass catchers or other attachments.

These can change the stability of the tractor. Always follow

the attachment manufacturer’s instructions.

17. Stop the blade(s) when crossing gravel drives, walks, or roads

and while not cutting grass.

18. Watch for traffic when operating near or crossing roadways.

This tractor is not intended for use on any public roadway.

19. Mow only in daylight or good artificial light.

20. Do not operate the tractor while under the influence of

alcohol or drugs.

21. Slow down before turning. Operate the tractor smoothly.

Avoid erratic operation and excessive speed.

22. Motors may become hot and can cause serious burn injuries.

Do not touch. Allow the tractor to cool for five minutes before

attempting any service.

23. Do not turn off tractor and freewheel downhill. Over-

speeding may cause the operator to lose control of the tractor

resulting in serious injury or death.

CHILDREN

1. Tragic accidents can occur if the operator is not alert to the

presence of children. Children are often attracted to the

tractor and the mowing activity. They do not understand the

dangers. Never assume that children will remain where you

last saw them.

2. Keep bystanders, children and pets inside while the tractor is

in operation under watchful care of a responsible adult other

than the operator. Stop tractor if anyone enters the area.

3. Never carry children, even with the blade(s) shut off. They

may fall off and be seriously injured or interfere with safe

tractor operation. Children who have been given rides in the

past could suddenly appear in the mowing area for another

ride and be run over or backed over by the tractor.

4. Be alert and turn tractor off if a child or bystander enters

the area.

5. To avoid back-over accidents, always look behind and down

for small children.

6. Use extreme care when approaching blind corners, doorways,

shrubs, trees or other objects that may block your vision of a

child who may run into the path of the tractor.

7. Never allow children under 14 years of age to operate this

tractor. Children 14 and over should read and understand

the instructions and safe operation practices in this manual

and on the tractor and should be trained and supervised by

an adult.

8. Do not allow any child to joy ride on the tractor. The tractor is

not a toy or a go-cart. Warn your children that the tractor can

be dangerous and they must stay away from it at all times.

9. Keep children away from hot or running tractor. They can

suffer burns from a hot motors.

10. Remove key when tractor is unattended to prevent

unauthorized operation. Make certain the key is inaccessible

to small children.

4

SAFE OPERATION PRACTICES

SLOPE OPERATION

1. Slopes are a major factor related to loss of control and tip-

over accidents which can result in severe injury or death. All

slopes require extra caution. If you cannot back up the slope

or if you feel uneasy on it, do not mow or drive on it.

2. For your safety, measure any slope before using the tractor

on the sloped area. Use a slope measuring device in addition

to the slope gauge included as part of this manual to measure

slopes before operating this tractor on a sloped or hilly area.

Smart phone applications can be also utilized to measure

slopes. If the slope is greater than 15 degrees (25%) as

shown on the slope gauge or a slope measuring device, do

not operate this tractor on that area or serious injury could

result.

3. Do not mow on slopes greater than 15 degrees (25%).

4. Do not mow up or down slopes, only mow across slopes that

are less than 15 degrees (25%). Use low speeds and avoid

sudden turns.

5. Do not mow on wet grass. Reduced traction could cause

sliding or a loss of control.

6. Do not operate tractor under any conditions where traction,

steering or stability is in question. Tires could slide even if the

wheels are stopped.

7. Avoid starting and stopping on slopes. Avoid making sudden

changes in speed or direction. Make turns slowly and

gradually.

8. Use extra care while operating tractor with grass catcher

or other attachment(s). They can affect the stability of the

tractor. Do not use grass catcher on slopes greater than 10

degrees (17%).

9. Do not try to stabilize the tractor by putting your foot on the

ground.

10. Keep all movement on the slopes slow and gradual. Do

not make sudden changes in speed or direction. Rapid

acceleration could cause the front of the tractor to lift and

rapidly roll over backwards, which could cause serious injury

or death.

11. Do not turn off tractor and freewheel downhill. Over-

speeding may cause the operator to lose control of the tractor

resulting in serious injury or death.

HAULING

1. Use properly secured full width ramps for loading and

unloading a tractor for transport.

2. Use extra care when loading or unloading the tractor into a

trailer or truck. This tractor should not be driven up or down

ramp(s), because the tractor could tip over, causing serious

personal injury. The tractor must be pushed manually on

ramp(s) to load or unload properly.

3. Raise the deck to the highest position for loading clearance.

4. Do not tow this tractor, damage to the drive motors can

occur.

TOWING

1. Do not tow a load that exceeds 250 lbs (113 kg) rolling weight

and never exceed 50 lbs (22 kg) tongue weight.

2. Do not attach towed equipment except at the hitch point of

the tractor.

3. Never allow children or others in or on towed equipment.

4. Do not tow on slopes greater than 5 degrees (9%). On slopes,

the weight of the towed equipment may cause loss of traction

and loss of control and/or the ability to stop.

5. Always use extra caution when towing with a tractor capable

of making tight turns (e.g. “zero-turn” tractor). Make wide

turns to avoid jack-knifing.

6. Travel slowly and allow extra distance to stop.

SERVICE

1. Keep tractor in good working order. Do not use the tractor

until worn or damaged parts are replaced.

2. Tractor blades are sharp. Wrap the blade or wear gloves, and

use extra caution when servicing them.

3. Remove the key and store the tractor indoors when not in

use. Allow the tractor to cool at least five minutes before

charging or storing.

4. Before cleaning, repairing, or inspecting, make certain the

blade(s) and all moving parts have stopped. Turn off tractor

and remove the key.

5. Check to make sure the blades come to complete stop in

not more than (5) five seconds after disengaging the blade

disengagement control per interval in the Maintenance

Schedule. Measure the stopping time with a stop watch. If

the blades do not stop completely in less than five seconds,

your tractor should be serviced professionally by an

authorized dealer.

6. Check the safety interlock system per the interval in the

Maintenance Schedule for proper function, as described

later in this manual. If the safety interlock system does not

function properly, have your tractor serviced professionally

by an authorized dealer.

7. Never tamper with the safety interlock system or other safety

devices. Check their proper operation regularly.

8. Check the blade(s) mounting bolt torque in accordance to

the Maintenance Schedule in this manual. Also, visually

inspect blade(s) for damage (e.g., excessive wear, bent,

cracked). Replace the blade(s) with the original equipment

manufacturer’s (O.E.M.) blade(s) only.

9. Use of service parts which do not meet the original

equipment specifications may lead to improper performance

and compromise safety.

10. Keep all nuts, bolts and screws tight to be sure the equipment

is in safe working condition. Review the Maintenance

Schedule chart in this manual for service interval information.

5

SAFE OPERATION PRACTICES

11. After striking a foreign object, stop the tractor, push the

Start/Stop button, and remove the key. Thoroughly inspect

the tractor for any damage. Repair the damage before

operating.

12. To reduce fire hazard, keep the motor(s) free of grass, leaves

and debris build-up. Follow the post operation tractor care

instructions in the Service and Maintenance section.

13. Check brake operation frequently as it is subjected to wear

during normal operation. Adjust and service as required.

14. Never attempt to make adjustments or repairs to the tractor

without removing the key.

15. Maintain or replace safety and instruction labels, as

necessary.

GENERAL ELECTRIC SAFETY

1. Do not expose the tractor to rain or wet conditions.

2. Do not service the tractor or handle electrical components

with wet hands.

3. Do not operate the tractor in the rain, in wet conditions or on

wet surfaces.

4. To reduce the risk of electric shock, avoid body contact with

grounded conductors, such as metal pipes or wire fences.

5. Do not operate the tractor in explosive atmospheres, such as

in the presence of flammable liquids, gases or dust.

6. For protection against risk of injury or electric shock, do

not replace blown fuses. Your tractor should be serviced

professionally by an authorized dealer.

7. Never douse or hose the tractor with water. Avoid getting

any liquid in the motors and electrical connections. Clean the

tractor after each use. Refer to Service and Maintenance. Do

not use solvents or strong detergents.

BATTERY CHARGER SAFETY

WARNING

Only use an OEM battery charger (T56XXX series ) to

charge the batteries in this tractor. DO NOT attempt to

charge any other batteries with the battery charger

specific to this tractor. Other types of batteries may

burst, causing fire, personal injury or property damage.

1. Recharge only with the charger specified by the

manufacturer. A charger that is suitable for one type of

battery may create a risk of fire when used with another

battery.

2. Do not use the charger in the rain, wet locations or in the

presence of flammable liquids or gasses.

3. A nameplate on the charger indicates the voltage used. Never

connect the charger to an AC voltage that differs from this

voltage.

4. An extension cord should not be used unless absolutely

necessary. Use of an improper extension cord could result in a

risk of fire, electric shock or electrocution.

5. Do not use multiple extension cords.

6. Make sure the extension cord is heavy enough to carry the

current drawn by the charger. An undersized extension cord

will cause a drop in line voltage, resulting in a loss of power

and overheating. If in doubt, use the next heavier gauge cord.

The smaller the gauge number, the heavier the cord.

MINIMUM WIRE SIZE FOR EXTENSION CORDS FOR 120

VOLT APPLIANCES USING 0-6 AMPS

Cord Length (ft.) 25 50 100 150

Wire Size (AWG) 16 16 16 14

7. Make sure the cords are in good condition. Inspect the

battery charger power cord and extension cord periodically.

Look closely for deterioration, cuts or cracks in the insulation.

If either cord is damaged in any manner while plugged in,

disconnect the cord from both the outlet and the charger. Do

not use a damaged cord. Damaged cords should be repaired

or replaced.

8. Do not abuse cords. Never pull or carry the charger by a cord.

Keep cords away from heat, oil, water, sharp edges, and

moving objects. Always grasp the plug when disconnecting

a cord.

9. Never modify a plug, cord or outlet in any way.

10. Ground Fault Circuit Interrupter (GFCI) protection should

be provided on the circuit(s) or outlet(s) to be used with

this charger. For an extra measure of safety, use receptacle

(outlet) with built-in GFCI protection.

11. Do not place the battery charger where cords might be

stepped on, tripped over or subjected to damage.

12. Keep the battery charger and cords in a cool and dry area.

13. Keep the battery charger and cords away from all liquids.

14. Do not allow small metal items or material such as steel wool,

aluminum foil or other foreign particles into the charger port.

15. Do not probe the charger with conductive material. There is a

risk of electric shock.

16. Do not cover the battery charger. The battery charger may

overheat.

17. Do not allow the battery or battery charger to overheat.

If they are warm, allow them to cool down. Only charge

batteries in temperatures between 32° and 104° F (0° and

40° C).

6

SAFE OPERATION PRACTICES

BATTERY SAFETY

1. Do not expose the battery to fire or to temperatures over 140º

F (60º C). Doing so could cause an explosion.

2. Handle battery with care. Do not short the battery with

conductive materials, such as rings, bracelets, keys, etc.

Shorting the battery may cause personal injury, damage to

the battery or a fire.

3. Do not attempt to charge a cracked or damaged battery.

4. Do not use or charge a wet battery or a battery that shows

any evidence of corrosion.

5. Do not use a damaged or modified battery. Doing so could

result in a fire, explosion or personal injury.

6. Do not dispose of the battery in a fire. The cell may explode.

Contact your local authorized service dealer for proper

battery recycling.

7. Exercise care in handling batteries in order not to short the

battery with conductive materials such as rings, bracelets,

and keys. The battery or conductor may be hot and cause

burns.

WARNING

The battery may present a risk of fire or chemical burn

if misused. Do not disassemble, overheat or incinerate

the battery.

Leakage from the battery may occur under extreme

usage, charging or temperature conditions or if the

battery is damaged, crushed or punctured. This leakage

indicates a failure of the battery and the battery should

be properly disposed of by an authorized service dealer.

If the battery leakage gets on your skin or eyes, follow

these steps:

• Immediately wash the skin and flush the eyes with cool

water for at least 20 minutes and seek immediate medical

attention.

• Contents of open battery cells may cause respiratory

irritation. Provide fresh air. If symptom persist, seek medical

attention.

• Ventilate the room and vacate the area if smoke and gases

are present. Gas and smoke in a confined area will present a

potential health risk.

• If the leakage gets on your clothing or shoes, remove, isolate

and wash the contaminated clothing thoroughly.

SLOPE GAUGE (BACK COVER)

WARNING

Slopes are a major factor related to tip-over and roll-over

accidents which can result in severe injury or death. All

slopes require extra caution. If you feel uneasy on the

slope, do not mow it. Do not mow on slopes greater than

15 degrees (25%). Only mow across slopes, never mow up

and down slopes.

USE THE SLOPE GAUGE ON THE BACK COVER AS SHOWN TO

DETERMINE IF A SLOPE IS TOO STEEP FOR SAFE OPERATION!

To check the slope, proceed as follows:

1. Open manual to page and fold along the dashed line.

2. Locate a vertical object on or behind the slope (e.g. a pole,

building, fence, tree, etc.)

3. Align either side of the slope gauge with the object.

4. Adjust gauge up or down until the left corner touches the

slope.

5. If there is a gap below the gauge, the slope is too steep for

safe operation.

7

SAFETY SYMBOLS

This page depicts and describes safety symbols that MAY appear on this mower. Read, understand, and follow all instructions on the

mower before attempting to assemble and operate.

Symbol Description

OPESymbol.com

WARNING – READ THE OPERATOR’S MANUAL(S)

Read, understand and follow all the safety rules and

instructions in the manual(s) and on the tractor before

attempting to operate this tractor. Failure to comply with

this information may result in personal injury or death.

Keep this manual in a safe location for future and regular

reference. Using a Smart Phone, scan the QR code symbol to

learn more information concerning the warnings contained

on this tractor. You can also go to www.OPESymbol.com for

more information.

DANGER — AVOID THROWN OBJECTS INJURY

Keep helpers at least 75’ (23 meters) from machine during

operation. Remove all stones, sticks, wire, bones, toys, and

other foreign objects which could be picked up and thrown

by the blade(s). Do not operate the tractor without the

discharge cover or entire grass catcher in its proper place.

WARNING — AVOID CHILD BACKOVER/RUNOVER/BLADE

INJURY

To avoid back-over accidents, always look behind and down

for small children. Never carry children, even with the

blade(s) shut off. Keep bystanders, children and pets inside

during operation under the watchful care of a responsible

adult other than the operator. Stop tractor if anyone enters

the area.

>

10 ft (3 m)

>

10 ft (3 m)

> 15 < 15

WARNING – AVOID TIP-OVER/ROLL-OVER INJURY

Do not operate machine on a slope greater than 15° (25%).

Do not mow up or down slopes, only mow across slopes that

are less than 15 degrees (25%). Use low speeds and avoid

sudden turns on slopes. Stay at least 10 feet (3 meters)

from drop-offs, ditches, embankments or the edge of

water.

WARNING — ELECTRIC SHOCK

Do not charge tractor in rain or wet locations. Do not

operate tractor in rain. Never douse or hose the tractor with

water.

WARNING – AVOID AMPUTATION INJURY

Do not put hands or feet near or under the cutting deck.

Contact with the blade(s) can amputate hands and feet.

WARNING – AVOID AMPUTATION INJURY

Do not put hands or feet near rotating parts or under the

cutting deck. Contact with the blade(s) can amputate hands

and feet. Ensure that all safety devices (guards, shields,

switches, etc.) are in place and working.

Do not put hands or feet near rotating

parts or under the cutting deck. Contact

with the blade(s) can amputate hands

and feet. Ensure that all safety devices

(guards, shields, switches, etc.) are in

place and working

8

SAFETY SYMBOLS

Symbol Description

WARNING – AVOID CRUSH/PINCH POINT INJURY

Read, understand and follow all the safety rules and

instructions in the manual(s) and on the tractor before

attempting to service this tractor. For foot lift models only,

the deck lift system is spring-assisted and under tension.

Always use the provided multi-tool to secure the lift system

in the locked position before attempting to remove the

mower deck.

WARNING – REMOVE KEY

Before beginning any work on this machine, remove the key

and observe all information contained in these instructions.

If you are leaving the riding mower unattended, always

remove the key to prevent unauthorized use by children

or others.

WARNING – CHARGING THE TRACTOR

Read, understand and follow all the safety rules and

instructions in the manual(s) and on the tractor before

attempting to charge this tractor. Do not charge tractor in

rain or wet locations. Do not operate tractor in rain.

WARNING — STORE TRACTOR INDOORS

Store tractor indoors at all times when not in use.

DANGER — DO NOT SERVICE

Many components on this tractor should only be serviced by

an authorized service dealer. Read this Operator’s Manual

before attempting to service this tractor.

WARNING

Your Responsibility—Restrict the use of this power machine to persons who read, understand and follow the

warnings and instructions in this manual and on the machine - SAVE THESE INSTRUCTIONS!

9

ASSEMBLY

NOTE: Reference to right and left hand side of the tractor is

observed from the operating position.

NOTE: Some components may come already assembled. If they

are already assembled, skip ahead to the next step.

Manually Moving the Tractor

CAUTION

Never tow your tractor. Towing the tractor with the rear

wheels on the ground may cause severe damage to the

drive motors.

The tractor can be moved as long as the parking brake is not set.

The tractor can be pushed slowly.

Install Hitch (If Necessary)

1. Locate Hitch (a) and install on the rear of the frame using the

two hex washer screws (b) provided (Figure 1).

NOTE: Hitch and hex washer screws will be in the hardware pack.

a

bb

Figure 1

Reposition Upper Hoop (If necessary)

The upper hoop may be positioned down for shipping purposes:

1. Remove the two hex washer screws (a) partially installed on

the frame (Figure 2).

2. Rotate the upper hoop (b) into position (Figure 2).

3. Secure hoop in place with the hex washer screws removed

in step 1. Torque the hex washer screws to 179-219 in-lbs

(20-25 N-m).

a

b

Figure 2

Install Operator’s Seat

KNOB ADJUST OR LEVER ADJUST

1. Cut any straps securing the seat assembly to the tractor.

Remove all packing material.

NOTE: Be careful not to cut the seat wiring harness.

2. Install the seat onto the seat pan (a) using hardware

provided.

• For a Knob Adjust seat: insert bolts (b) in the rear holes

and lock washer (c) and knobs (d) in the front. Tighten

securely (Figure 3).

• For a Lever Adjust seat: use flange lock nuts (a) and flat

washers (b) (Figure 4).

a

b

c

ddc

Figure 3

a

bb

c

a

aa

Figure 4

10

ASSEMBLY

3. If necessary, securely connect the seat switch wiring harness

(a) to the seat switch (b) (Figure 5). Secure excess wire away

from pinch points before continuing.

a

b

Figure 5

NOTE: The tractor will not operate without the seat switch wiring

harness connected.

Position Lapbar Drive Control Levers

The lapbar drive control levers can be adjusted up/down and

forward/backward for the operator’s comfort. Three height

positions are available and/or levers can be rotated forward or

rearward using the knob.

TO ADJUST THE LAPBAR DRIVE CONTROL LEVER HEIGHT:

1. Remove the two carriage screws (a) and two flange lock nuts

(b) that secure the lapbar drive control lever (c) to the upper

handle adjuster (d) (Figure 6).

NOTE: The multi-tool (if equipped) can be used to make this

adjustment. Refer to Multi-Tool (If equipped) on page 14.

2. Move the lapbar drive control lever into one of the three

available heights and secure in place with the carriage screws

and flange lock nuts (Figure 6).

c

a

b

d

Figure 6

TO ADJUST THE LAPBAR DRIVE CONTROL LEVERS

FORWARD/REARWARD:

1. Rotate the knob (a) counter-clockwise to loosen the knob (a)

(Figure 7).

2. Lift and rotate the lapbar drive control lever into the desired

position.

3. Rotate the knob clockwise to secure the lapbar drive control

lever into position (Figure 7).

aa

Figure 7

4. If the lapbars do not line up after making the knob

adjustment, loosen nuts (b), align lapbars and retighten nuts.

Once this fine adjustment is made, the lapbars will align

when using the knob adjustment (Figure 7).

Lower Discharge Chute Deflector

WARNING

Never operate the cutting deck without the chute

deflector installed and in the down position.

ATTACHING THE CHUTE DEFLECTOR IF NECESSARY

1. If necessary, remove the keys attached with a zip tie to the

chute bracket.

2. Align the two chute deflector mounting holes (a) with the to

deck mounting holes (b).

3. Using two carriage bolts (c) and two flange nuts (d), secure

the chute deflector to the deck (Figure 8). Tighten to 170-200

in-lbs (18.5-23 N-m) (Figure 8). Skip ahead to Setting Deck

Wheels.

d

a

c

b

Figure 8

11

ASSEMBLY

REMOVING THE STOP BRACKET IF NECESSARY

1. If the chute is shipped attached and with a stop bracket

holding the chute upright, the stop brackets must be

removed prior to operating the tractor.

2. Holding the chute deflector fully upward, remove the stop

bracket. Lower the chute deflector and discard the stop

bracket (Figure 9).

Figure 9

Setting Deck Wheels (If equipped)

NOTE: The deck wheels are an anti-scalp feature of the deck and

are not designed to support the weight of the cutting deck.

1. Move the tractor to a level surface, preferably pavement.

2. Check tire pressure, adjust, if necessary. See tire side wall for

proper tire pressure.

3. Make sure the deck is level side-to-side and properly pitched.

See the Service and Maintenance section for deck leveling

information and instructions.

4. Place deck lift lever or knob in the desired mowing height

position and lower deck.

5. Check the wheels for contact or excessive clearance with the

surface below.

NOTE: The deck wheels should have between ¼” (6.35mm) and

½” (12.7mm)clearance above the ground.

6. Remove the lock nut (a) gauge wheel (b) and shoulder screw

(c) from the deck (Figure 10).

7. Insert the shoulder screw into one of four index holes on deck

wheel bracket. Allow a 1⁄4-1⁄2” (6.35-12.7 mm)clearance

between the ground and gauge wheel.

8. Note the index hole used on previously adjusted wheel.

Repeat adjustment on opposite side to align both gauge

wheels.

NOTE: Refer to Adjusting the Deck section of this manual for

more detail.

a

b

c

Figure 10

Checking Tire Pressure

See the tire sidewall for the proper inflation pressure. Proper

inflation pressure should be maintained at all times.

Charging the Battery

WARNING

California Proposition 65: Cancer and reproductive harm

– www.P65Warnings.ca.gov.

The battery contains corrosive fluid and toxic material

— HANDLE WITH CARE. Keep away from children. Do not

puncture, disassemble, mutilate, or incinerate. Explosive

gases could be vented during charging or discharging.

Charge in a well ventilated area, away from sources of

ignition.

Recharge only with the charger provided with this

tractor. A charger that is not suitable for this tractor may

damage the batteries or create the risk of fire.

Do not charge or operate the tractor in the rain or in wet

conditions.

Refer to the manual packed with your battery charger for

further information and instructions on charging the battery.

The charging port on the tractor is located on the left side of the

mower.

To charge the battery:

1. Lift the charging port cover (a) (Figure 11).

2. Insert the charging cord (b) into the charging port (c)

(Figure 11).

3. Plug charger power cord into wall receptacle (outlet).

a

c

b

Figure 11

12

ASSEMBLY

NOTE: It will take approximately 4 hours to fully charge the

battery.

NOTE: The battery icon on the Vehicle Control Module (VCM)

will blink continuously when charging and the LCD display will

display percentage of charge. The battery is completely charged

when the battery icon is solid and the LCD displays 100%.

NOTE: When the charging cord is plugged into the tractor and

not yet plugged into the wall, the battery icon will illuminate

continuously until the cord is plugged into the wall.

If at any time your charger displays a fault while charging your

battery, follow these procedures:

1. Power off the tractor.

2. Unplug the charging cord from the tractor.

3. Unplug the charger power cord from the power source.

4. Plug the charger power cord back into the power source.

5. Plug the charging cord back into the tractor.

6. If the fault persists contact qualified service personnel.

NOTE: Rechargeable batteries degrade with time and use. The

battery may eventually need to be replaced. To have the battery

replaced, contact your authorized Service Dealer.

NOTE: Using old or faulty battery could cause a system fault that

results in loss of power.

BATTERY CHARGING TIPS

• The battery should be fully charged before the initial use.

• The battery should be fully charged after each use. Storing

the battery in a discharged state could reduce performance.

• The battery will turn off automatically after a complete

charge.

• It will take approximately 4 hours to fully charge the

battery. Leaving the battery connected to the charger for

more than 4 hours will not damage the battery.

• The battery does not develop a memory and does not need

to be fully discharged before recharging.

• Always disconnect battery charger (or extension cord, if

used) from the electrical receptacle (outlet) first, then

disconnect the charging cord from the charging port.

• Never charge a frozen battery.

• It is recommended that the tractor be charged once every

month during off-season storage.

Adjusting the Seat

WARNING

Before operating the tractor, make sure the seat is

engaged in the seat-stop. Engage the parking brake.

Stand behind the tractor and pull back on seat until it

clicks into place.

KNOB ADJUST

1. Remove the knobs (a).

2. Slide the seat up or down into the desired position.

3. Replace the knobs into one of the four hole settings and

tighten securely (Figure 12).

a

Figure 12

LEVER ADJUST

1. Push left and hold the seat adjustment lever to adjust the

seat position.

2. Slide seat forward or rearward to desired position.

3. Release the adjustment lever. Ensure seat is locked into

position before operation (Figure 13).

Figure 13

13

OPERATION

B1 B2

D2

D1

A

B

C

E

F

G

H

I

Figure 14

A. LAPBAR DRIVE CONTROL LEVERS

The RH (Right Hand) and LH (Left Hand) lapbar drive control

levers are located on each side of the operator’s seat. The hinged

levers pivot outward to permit the operator to sit in the seat,

or dismount. To start the tractor, the lapbar drive control levers

must be fully out and in park position.

Each drive control lever controls the respective motor.

Consequently, these levers control all of the tractors movement.

Driving and steering using these control levers is quite different

from a conventional tractor and will take practice to master.

Refer to Practice Operation section for further instructions.

B. DECK LIFT

Deck Lift Pedal - The deck lift pedal is located on the front,

right corner of the platform. The pedal is used in conjunction

with the deck lift knob or 8 position magnetic pin (if

equipped) to raise and lower the mowing deck.

1. Deck Height Index Knob (If Equipped) - Each rotation

represents a ⁄” (6.35 mm) change in deck height.

Positions range from 1” (2.5 cm) to 4-½” (11.4 cm) at the

highest point. Push forward on the deck lift pedal, rotate

the deck height index knob to the desired height and

release the deck lift pedal.

2. 8 Position Magnetic Pin (If equipped) - The 8 position

magnetic pin is used in conjunction with the deck lift

pedal to raise and lower the mowing deck. Push forward

on the deck lift pedal, place the 8 position magnetic pin in

the desired height and release the deck lift pedal.

NOTE: Amount of deck height change is dependent on

depth of deck lift pedal press. The more height change

needed, the more the deck lift pedal should be pushed

forward.

14

OPERATION

3. LCD Screen & Battery Level Indicator - Located on the

VCM, the LCD display & battery level indicator are used

to provide instructions, warnings and information about

your tractor systems and the battery level of your tractor.

4. PTO (Blades ON/OFF) Button - Located on

the VCM, the PTO button is used to operate the

blades. To engage the cutting deck (blades ON),

press and hold the PTO button for three seconds.

The yellow indicator light around the PTO button is ON

Pressing the PTO button again will disengage the cutting

deck (Blades OFF). The yellow indicator light around the

PTO button is OFF.

5. Eco Mode Button - Eco mode slightly

reduces blade speed to increase battery run

time of the tractor in areas of low grass load.

6. Low Speed Precision Drive Button -

Low speed precision drive enhances

maneuverability and control by setting

maximum forward speed to 4 mph

and is recommended when

loading/unloading the tractor on a

trailer, mowing on rough terrain,

around a perimeter, and in tight

spaces.

7. Headlight Button - Located on the VCM the

headlight button is used to turn the headlights on

or off.

D. MULTITOOL IF EQUIPPED

The multi-tool (a) is located on the front of the right console

(E1, Figure 14) or on the top, rear of the left console (E2, Figure

14). The multi-tool (a) can be used as a deck lift lockout, to

remove the footpan bolt, adjust the height of the lapbar drive

control levers, drive control lever stop adjustment and can be

used as a removal tool with the 1/2” socket end. See the Service

and Maintenance section for more information on multi-tool

(a) usage.

E. BRAKE PEDAL

The brake pedal is located in the center of the tractor, in front

of the floor pan. The brake pedal can be used for stopping the

tractor or setting the parking brake.

Setting The Parking Brake

1. Push the brake pedal (a) all the way forward (Figure 17).

2. Rotate the brake pedal pad (b) forward to engage the

parking brake latch (c).

3. Ensure the brake pedal pad is fully engaged with the

parking brake latch.

4. To disengage the parking brake, push the brake pedal (a)

forward.

C. VEHICLE CONTROL MODULE VCM

WARNING

Never leave a running tractor unattended. Always

disengage PTO, set parking brake, stop tractor and

remove the key to prevent unintended starting.

The vehicle control module (VCM) is located on the right console.

The VCM (Figure 15) is the location of several control buttons

for your tractor. The VCM includes the START/STOP button, PTO

(blades ON/OFF) button ,Eco Mode Button, Headlight Button,

Low Drive Speed Button, LCD Screen and the Battery Level

Indicator.

12

3

4

5

6

7

Figure 15

WARNING

Prior to operating the tractor, refer to both Safety

Interlock System and Starting The Tractor in the

Operation section of this manual for detailed instructions

regarding the VCM and operating the tractor.

1. Start/Stop Button - Located on the VCM,

the start/stop button is used to start and stop

the tractor. While active, the start/stop button

indicator ring is illuminated blue.

2. Key Switch - The key switch is located in the center

of the VCM and powers the VCM when the key is fully

inserted. The tractor cannot be started unless the key is

fully inserted and the START/STOP button is depressed.

Removing the key turns the tractor off (Figure 16).

Figure 16

15

OPERATION

Operation

Safety Interlock System

WARNING

Do not operate the tractor if the safety interlock system

is malfunctioning. This system was designed for your

safety and protection.

This tractor is equipped with a safety interlock system for the

protection of the operator. If the interlock system should ever

malfunction, do not operate the tractor. Contact an authorized

service dealer.

• The safety interlock system prevents the operator from

turning the tractor ON unless the operator is in the seat with

the parking brake set.

• The tractor will not operate with the charger cord plugged

into the charging port.

• The tractor will automatically shut off the blade(s) and drive

motors if the operator leaves the seat.

CHECKING THE SAFETY INTERLOCK CIRCUITS

• With the tractor running, Disengage parking brake. Lift

upward from the operator’s seat; the tractor should stop.

• With the parking brake engaged, press the PTO button to

engage the blades. Lift upward from the operator’s seat; the

tractor should stop.

NOTE: The brake pedal must be fully depressed to start the

tractor. Refer to Safety Interlock System for more information.

a

c

b

a

Figure 17

F. USB CHARGING PORTS IF EQUIPPED

If equipped, a USB power source is located to

the right of the operator’s seat. The USB port

is rated 2.1A. The port can be used to charge

your phone or power up other USB devices.

G. CUP HOLDER

The cup holder is located to the right of the operator’s seat.

H. STORAGE TRAY

The storage tray is located to the right of the operator’s seat.

I. CHARGING PORT

The charging port is located to the left of the operator’s seat. To

access the charging port, lift up on the charging port cover.

WARNING

Do not have any devices plugged into your USB charging

port when starting the tractor. Doing so may cause

damage to your device.

J. SEAT ADJUSTMENT LEVER NOT SHOWN/IF EQUIPPED

The seat adjustment lever is located under the seat. The seat

adjustment lever allows for adjustment forward or backward of

the operator’s seat. Refer to the Assembly & Set-Up section for

instructions on adjusting the seat position.

Note: If your tractor is not equipped with a seat adjustment

lever, it can be adjusted using the knobs on the underside of the

seat. Refer to the Assembly & Set-Up section for instruction on

adjusting the seat.

16

OPERATION

Starting the Tractor

1. Unplug the charging cord (if necessary) (Figure 18). If the cord

is still plugged in a reminder will display on the VCM when

the key switch is turned on.

Figure 18

2. Sit in the operator’s seat. Fully insert the key into the key

switch.

3. Set the lapbar drive control levers fully out (Figure 19).

Control Levers Moved

Outward

Figure 19

4. Push brake pedal in.

5. Press the start/stop button down until you hear

two beeps.

NOTE: The VCM and drive motors are now activated and the

tractor is ready to be operated.

6. Set the lapbar driving control levers fully inward and in the

neutral position. Disengage the parking brake when ready to

move the tractor (Figure 20).

NOTE: Any time after the brake is pressed, both lapbar driving

control levers must return to the neutral position for the tractor

to operate.

Stopping the Tractor

WARNING

If you strike a foreign object, stop the tractor, and

remove the key. Thoroughly inspect the tractor for

any damage. Repair the damage before restarting and

operating.

1. Move both lapbar drive control levers to the neutral position

to stop the motion of the tractor.

2. If the cutting deck is engaged (blades ON), press the PTO

button to disengage the blades (blades OFF).

3. Set the lapbar drive control levers fully out.

4. Use the deck lift knob/pedal to raise the deck to its highest

position.

5. Engage the park brake.

6. Press the start/stop button (you will hear one beep).

7. Remove the key to prevent unauthorized use by children or

others.

Driving the Tractor

WARNING

Keep all movement of the lapbar drive control levers slow

and smooth. Abrupt movement of the control levers can

affect the stability of the tractor and could cause the

tractor to flip over, which may result in serious injury or

death to the operator.

1. Adjust the operator’s seat to the most comfortable position

that allows you to operate the controls. See seat adjustment

in the Assembly section.

2. Move the RH and LH lapbar drive control levers inward to the

neutral position (Figure 20) and disengage the parking brake.

Control Levers Moved

Inward & in Neutral

Figure 20

17

OPERATION

Turning the Tractor While Driving Forward

WARNING

Sharp turns can affect control of the tractor. ALWAYS slow

the tractor before making sharp turns.

To turn the tractor while driving forward, move the lapbar drive

control levers as necessary so that one drive control lever is

rearward of the other. The tractor will turn in the direction of the

rearward drive control lever.

1. To turn to the left, move the left drive control lever rearward

of the right drive control lever (Figure 22).

Forward Left Turn

Figure 22

2. To turn to the right, move the right drive control lever

rearward of the left lever (Figure 23).

Forward Right Turn

Figure 23

3. The greater the distance between the two levers, the sharper

the tractor will turn.

4. To execute a “pivot turn,” move the turn side drive control

lever to the neutral position, while moving the other control

lever forward.

NOTE: Making a “pivot turn” on grass will greatly increase the

potential for defacement of the turf.

NOTE: Lapbar drive control levers must be moved fully inward

and the park brake disengaged before driving the tractor.

NOTE: If the lapbar drive control levers are not even in the neutral

position, refer to Service and Maintenance for instructions to

adjust the lapbar drive control levers so that they are even.

WARNING

Always maintain a firm grip on the control levers. DO

NOT release the control levers to slow or stop the tractor;

move levers to neutral position using your hands.

3. To drive the tractor, firmly grasp the respective lapbar drive

control levers with your right and left hands and continue

with Driving the Tractor Forward in the next section.

Driving the Tractor Forward

1. Slowly and evenly move both lapbar drive control levers

forward. The tractor will start to move forward (Figure 21).

Driving Forward Faster

Slower

Neutral

Position

Figure 21

2. As the lapbar drive control levers are pushed farther forward

the speed of the tractor will increase.

3. To slow the tractor move the drive controls lever rearward

to attain the desired speed, or move the lapbar drive control

levers to the neutral position to stop the tractor.

18

OPERATION

Driving the Tractor in Reverse

WARNING

Always look behind and down on both sides of the tractor

before backing up. Always look behind while traveling

in the reverse direction. Mowing in reverse is not

recommended.

1. Slowly and evenly move both lapbar drive control levers

rearward. The tractor will start to move in the reverse

direction (Figure 24).

Slower

Faster

Neutral

Position

Figure 24

2. As the lapbar drive control levers are pushed farther rearward

the speed of the tractor will increase.

3. To slow the tractor move the lapbar drive control levers

forward to attain the desired speed, or move the lapbar drive

control levers to the neutral position to stop the tractor.

Turning While Driving Rearward

To turn the tractor while driving rearward, move the lapbar

drive control levers as necessary so that one drive control lever is

forward of the other. The tractor will turn in the direction of the

forward lapbar drive control lever.

1. To turn to the left while traveling in reverse, move the left

drive control lever forward of the right drive control lever

(Figure 25).

Rearward Left Turn

Figure 25

2. To turn to the right while traveling in reverse, move the right

drive control lever forward of the left drive control lever

(Figure 26).

Rearward Right Turn

Figure 26

NOTE: The greater the distance between the two lapbar drive

control levers, the sharper the tractor will turn.

3. To execute a “pivot turn,” move the turn side drive control

lever to the neutral position, while moving the other drive

control lever rearward.

NOTE: Making a “pivot turn” on grass will greatly increase the

potential for defacement of the turf.

19

OPERATION

Executing a Zero Turn

1. Stop the forward or reverse motion of the tractor by moving

the two lapbar drive control levers to neutral

2. To turn clockwise, move the left lapbar drive control lever

forward while simultaneously moving the right lapbar drive

control lever rearward (Figure 27).

Rearward Right Turn

Figure 27

3. To turn counterclockwise, move the lapbar right drive control

lever forward while simultaneously moving the left lapbar

drive control lever rearward (Figure 28).

Counterclockwise Zero Turn

Figure 28

Operating the PTO

To operate the PTO (Blades ON/OFF) proceed as follows:

Press the PTO button for three seconds. When activated the

yellow indicator light under the PTO button is ON (Blades ON).

Press the PTO button again for three seconds, green indicator

light is OFF (Blades OFF).

Mowing

WARNING

To help avoid blade contact or a thrown object injury,

keep bystanders, helpers, children and pets at least 75

feet (23 meters) from the tractor while it is in operation.

Keep bystanders, children and pets inside during

operation. Stop tractor if anyone enters the area.

Plan your mowing pattern to avoid discharge of materials

toward roads, sidewalks, bystanders and the like. Also,

avoid discharging material against a wall or obstruction

which may cause discharged material to ricochet back

toward the operator.

The following information will be helpful when using the cutting

deck with your tractor:

1. Do not mow or drive at high ground speed, especially if a

mulch kit or grass collector is installed.

2. For best results it is recommended that the first two laps be

cut clockwise with the discharge facing towards the center

of your lawn. After the first two laps, reverse the direction to

discharge to the outside for the balance of cutting. This will

give a better appearance to the lawn.

3. Do not cut the grass too short. Short grass invites weed

growth and yellows quickly in dry weather.

4. Under heavier conditions it may be necessary to go back over

the cut area a second time to get a clean cut.

5. Do NOT attempt to mow heavy brush and weeds and grass

taller than 10” (25.4 cm). Your tractor is designed to mow

lawns, NOT clear brush.

20

SERVICE AND MAINTENANCE

WARNING

Before inspecting, cleaning or servicing the tractor, power

off the tractor and remove the key.

Follow the maintenance schedule given below. This chart

describes service guidelines only. Use the Service Log column

to keep track of completed maintenance tasks. Contact an

authorized service dealer to schedule a service.

IMPORTANT: Bring the battery charger when arriving at your

authorized service dealer for any scheduled service.

DANGER

The electrical components on this tractor are not

serviceable. Please contact an authorized service dealer

for any service needs.

Have your tractor serviced by qualified service personnel

using only identical replacement parts. This will ensure

that the safety of the tractor is maintained.

NOTE: At relevant service intervals on

start-up, service minders will be

displayed on the VCM. To clear service

minders press the low drive speed (Turtle) button. (S02) shown

for example.

Prior

to

Use

After

First

Five

Hours

(S01)

Every

Five

Hours

(S02)

Every

10

Hours

(S03)

Every

25

Hours

(S04)

Every

50

Hours

(S05)

Every

100

Hours

(S06)

Prior to

Storing

Clean Top and Underside of Deck P P

Check/Clean Around fuses,

Wiring and Wiring Harnesses P P

Check/Clean Around

Transmission and Axle P P

Clean Tractor P

Lube Front Rims P P

Lube Pedal Pivot Points,

Parking Brake and Lift Linkage P P

Check Tire Pressure/Inflate

to Sidewall Specification P P

Check Deck Level/Pitch/Adjust

as needed P P

Check Blade(s)/Sharpen or

Replace as Needed P P P

Charge Battery P P

Check Safety Interlock System P

Check Tractor Blade Stop Time P

Check Blade Mount Bolt Torque

(Tighten to 450-600 in-lbs

(51.9–67.8 N-m))

P P P

Sharpen Blades P

Check That All Hardware is in

Place and Secure P P

La page charge ...

Troy-Bilt TROY-BILT 34B2C Battery Powered Brushless Zero Turn Tractor Manuel utilisateur

Troy-Bilt TROY-BILT 34B2C Battery Powered Brushless Zero Turn Tractor Manuel utilisateur

dans d''autres langues

Autres documents