Bolens 13AX79GH565 Le manuel du propriétaire

Marque: Bolens

Modèle: 13AX79GH565

Catégorie: Tondeuses à gazon

Taper: Le manuel du propriétaire

Ce manuel convient également à

13AN79GG565

769-04814

1/28/09

Hydrostatic Lawn Tractor — Models 790

PRINTED IN U.S.A. P. O. Box 1386, KITCHENER, ONT. N2G 4J1

IMPORTANT:

READ SAFETY RULES AND INSTRUCTIONS

CAREFULLY BEFORE OPERATING EQUIPMENT.

Safety • Set-Up • Operation • Adjustments • Maintenance • Troubleshooting • Warranty

OPERATOR’S MANUAL

Table of Contents

BEFORE YOU START ASSEMBLING

YOUR NEW EQUIPMENT,

please locate the model plate on the equipment and copy

the information from it in the space provided below. You can

locate the model number by looking beneath the seat. This

information will be necessary to use the manufacturer’s web

site and/or help from the Customer Support Department or an

authorized service dealer.

This Operator’s Manual is an important part of your new equipment. It will help you assemble,

prepare and maintain the unit for best performance. Please read and understand what it says.

Finding and Recording Model Number

Please do

NOT

return the unit to the retailer from which it was purchased,

without rst contacting Customer Support.

Customer Support

Slope Gauge........................................................ 3

Safe Operation Practices ................................... 4

Setting Up Your Lawn Tractor ............................ 8

Operating Your Lawn Tractor ........................... 12

Adjusting Your Lawn Tractor ............................ 19

Maintaining Your Lawn Tractor ........................ 20

Off-Season Storage / Attachments ................. 26

Safety Labels .................................................... 27

Trouble Shooting .............................................. 28

Warranty ............................................................ 29

Replacement Parts ........................................... 30

If you have difficulty assembling this product or have any questions regarding the controls, operation or maintenance of this unit,

you can seek help from the experts. Choose from the options below:

1. Visit www.bolens.ca for many useful suggestions, click on Customer Support button.

2. Call a Customer Support Representative at 1-800-668-1238.

3. The engine manufacturer is responsible for all engine-related issues in terms of performance, power-rating, specifications,

warranty, and service. Depending on the engine manufacturer, more information is included in this publication or packed

separately with this product.

Please have your unit’s model number and serial number ready when you call. See previous section to locate this information.

You will be asked to enter the serial number in order to process your call.

Mo d e l Nu M b e r

Se r i a l Nu M b e r

Slope

Gauge

WARNING

Do not mow on inclines

with a slope in excess

of 15 degrees (a rise

of approximately

2-1/2 feet every 10

feet). A riding mower

could overturn and

cause serious injury.

If operating a walk-

behind mower on such

a slope, it is extremely

difficult to maintain your

footing and you could

slip, resulting in serious

injury.

Operate RIDING

mowers up and down

slopes, never across

the face of slopes.

Operate

WALK-BEHIND

mowers across the

face of slopes, never

up and down slopes.

Sight and hold this level with a vertical tree...

or a corner of a building...

or a fence post

Fold along dotted line (represents a 15° slope)

15°

Use this page as a guide to determine slopes where you may not operate safely. Do not operate

your lawn mower on such slopes.

General Operation

1. Read, understand, and follow all instructions on the ma-

chine and in the manual(s) before attempting to assemble

and operate. Keep this manual in a safe place for future

and regular reference and for ordering replacement parts.

2. Be familiar with all controls and their proper operation.

Know how to stop the machine and disengage them

quickly.

3. Never allow children under 14 years old to operate this

machine. Children 14 years old and over should read and

understand the instructions and safe operation practices

in this manual and on the machine and should be trained

and supervised by a adult.

4. Never allow adults to operate this machine without proper

instruction.

5. To help avoid blade contact or a thrown object injury, keep

bystanders, helpers, children and pets at least 75 feet

from the machine while it is in operation. Stop machine if

anyone enters the area.

6. Thoroughly inspect the area where the equipment is to

be used. Remove all stones, sticks, wire, bones, toys,

and other foreign objects which could be picked up and

thrown by the blade(s). Thrown objects can cause serious

personal injury.

7. Plan your mowing pattern to avoid discharge of material

toward roads, sidewalks, bystanders and the like. Also,

avoid discharging material against a wall or obstruction

which may cause discharged material to ricochet back

toward the operator.

8. Always wear safety glasses or safety goggles during

operation and while performing an adjustment or repair

to protect your eyes. Thrown objects which ricochet can

cause serious injury to the eyes.

9. Wear sturdy, rough-soled work shoes and close-fitting

slacks and shirts. Loose fitting clothes and jewelry can be

caught in movable parts. Never operate this machine in

bare feet or sandals.

10. Be aware of the mower and attachment discharge

direction and do not point it at anyone. Do not operate the

mower without the discharge cover or entire grass catcher

in its proper place.

11. Do not put hands or feet near rotating parts or under the

cutting deck. Contact with the blade(s) can amputate

hands and feet.

12. A missing or damaged discharge cover can cause blade

contact or thrown object injuries.

13. Stop the blade(s) when crossing gravel drives, walks, or

roads and while not cutting grass.

14. Watch for traffic when operating near or crossing

roadways. This machine is not intended for use on any

public roadway.

15. Do not operate the machine while under the influence of

alcohol or drugs.

16. Mow only in daylight or good artificial light.

17. Never carry passengers.

18. Disengage blade(s) before shifting into reverse. Back up

slowly. Always look down and behind before and while

backing to avoid a back-over accident.

19. Slow down before turning. Operate the machine smoothly.

Avoid erratic operation and excessive speed.

20. Disengage blade(s), set parking brake, stop engine and

wait until the blade(s) come to a complete stop before

removing grass catcher, emptying grass, unclogging chute,

removing any grass or debris, or making any adjustments.

21. Never leave a running machine unattended. Always turn off

blade(s), place transmission in neutral, set parking brake,

stop engine and remove key before dismounting.

22. Use extra care when loading or unloading the machine into

a trailer or truck. This unit should not be driven up or down

ramp(s), because the unit could tip over, causing serious

personal injury. The unit must be pushed manually on

ramp(s) to load or unload properly.

23. Muffler and engine become hot and can cause a burn. Do

not touch.

24. Check overhead clearances carefully before driving under

low hanging tree branches, wires, door openings etc., where

the operator may be struck or pulled from the unit, which

could result in serious injury.

25. Disengage all attachment clutches, depress the brake pedal

completely and shift into neutral before attempting to start engine.

26. Your machine is designed to cut normal residential grass of

a height no more than 10”. Do not attempt to mow through

unusually tall, dry grass (e.g., pasture) or piles of dry leaves.

Dry grass or leaves may contact the engine exhaust and/

or build up on the mower deck presenting a potential fire

hazard.

27. Use only accessories and attachments approved for this

machine by the machine manufacturer. Read, understand

and follow all instructions provided with the approved acces-

sory or attachment.

28. Data indicates that operators, age 60 years and above, are

involved in a large percentage of riding mower-related inju-

ries. These operators should evaluate their ability to operate

the riding mower safely enough to protect themselves and

others from serious injury.

29. If situations occur which are not covered in this manual, use

care and good judgment. Contact your customer service

representative for assistance.

DANGER: This machine was built to be operated according to the rules for safe operation in this manual.

As with any type of power equipment, carelessness or error on the part of the operator can result in serious

injury. This machine is capable of amputating hands and feet and throwing objects. Failure to observe the

following safety instructions could result in serious injury or death.

Safe

Operation

Practices

This symbol points

out important safety

instructions which, if

not followed, could

endanger the personal

safety and/or property

of yourself and others.

Read and follow all

instructions in this man-

ual before attempting to

operate this machine.

Failure to comply with

these instructions

may result in personal

injury. When you see

this symbol, HEED ITS

WARNING.

Your

Responsibility

Restrict the use

of this power machine

to persons who read,

understand

and follow the warnings

and instructions

in this manual and on

the machine.

WARNING: Engine Exhaust, some of its constituents, and certain vehicle components

contain or emit chemicals known to State of California to cause cancer and birth defects

or other reproductive harm.

Slope Operation

Slopes are a major factor related to loss of control and tip-over

accidents which can result in severe injury or death. All slopes

require extra caution. If you cannot back up the slope or if you

feel uneasy on it, do not mow it.

For your safety, use the slope gauge included as part of this

manual to measure slopes before operating this unit on a

sloped or hilly area. If the slope is greater than 15 degrees as

shown on the slope gauge, do not operate this unit on that area

or serious injury could result.

Do:

1. Mow u

p and down slopes, not across. Exercise extreme

caution when changing direction on slopes.

2. Watch for holes, ruts, bumps, rocks, or other hidden objects.

Uneven terrain could overturn the machine. Tall grass can

hide obstacles.

3. Use slow speed. Choose a low enough speed setting so that

you will not have to stop or shift while on the slope. Tires may

lose traction on slopes even though the brakes are function-

ing properly. Always keep machine in gear when going down

slopes to take advantage of engine braking action.

4. Follow the manufacturer’s recommendations for wheel

weights or counterweights to improve stability.

5. Use extra care with grass catchers or other attachments.

These can change the stability of the machine.

6. Keep all movement on the slopes slow and gradual. Do not

make sudden changes in speed or direction. Rapid engage-

ment or braking could cause the front of the machine to lift

and rapidly flip over backwards which could cause serious

injury.

7. Avoid starting or sto

pping on a slope. If tires lose

traction, disengage the blade(s) and proceed slowly

straight down the slope.

Do Not:

1. Do not turn on slopes unless necessary; then, turn slowly

and gradually downhill, if possible.

2. Do not mow near drop-offs, ditches or embankments. The

mower could suddenly turn over if a wheel is over the edge

of a cliff, ditch, or if an edge caves in.

3. Do not try to stabilize the machine by putting your foot on

the ground.

4. Do not use a grass catcher on steep slopes.

5. Do not mow on wet grass. Reduced traction could cause

sliding.

6. Do not shift to neutral and coast downhill. Over-speeding

may cause the operator to lose control of the machine

resulting in serious injury or death.

7. Do not tow heavy pull behind attachments (e.g. loaded

dump cart, lawn roller, etc.) on slopes greater than 5

degrees. When going down hill, the ex

tra weight tends to

push the tractor and may cause you to loose control.

(e.g. tractor may speed up, braking and steering ability

are reduced, attachment may jack-knife and cause

tractor to overturn).

Children

1. Tragic accidents can occur if the operator is not alert to the

presence of children. Children are often attracted to the

machine and the mowing activity. They do not understand

the dangers. Never assume that children will remain where

you last saw them.

a. Keep children out of the mowing area and in watchful

care of a responsible adult other than the operator.

b. Be alert and turn machine off if a child enters the area.

c. Before and while backing, look behind and down for

small children.

d. Never carry children, even with the blade(s) shut off.

They may fall off and be seriously injured or interfere

with safe machine operation.

e. Use extreme care when approaching blind corners,

doorways, shrubs, trees or other objects that may

block your vision of a child who may run into the

machine.

f. To avoid back-over accidents, always disengage

the cutting blade(s) before shifting into Reverse. If

equipped, the “Reverse Caution Mode” should not be

used when children or others are around.

g. Keep children away from hot or running engines. They

can suffer burns from a hot muffler.

h. Remove key when machine is unattended to prevent

unauthorized operation.

2. Never allow children under 14 years old to operate this

machine. Children 14 years old and over should read

and unde

rstand the instructions and safe operation

practices in this manual and on the machine and

should be trained and supervised by a adult.

Towing

1. Tow only with a machine that has a hitch designed for

towing. Do not attach towed equipment except at the hitch

point.

2. Follow the manufacturers recommendation for weight

limits for towed equipment and towing on slopes.

3. Never allow children or others in or on towed equipment.

4. On slopes, the weight of the towed equipment may cause

loss of traction and loss of control.

5. Always use extra caution when towing with a machine

capable of making tight turns (e.g. “zero-turn” ride-on

mower). Make wide turns to avoid jack-knifing.

6. Travel slowly and allow extra distance to stop.

6. Do not shift to neut

ral and coast downhill.

Service

Safe Handling of Gasoline:

1. To avoid personal injury or property damage use

extreme care in handling gasoline. Gasoline is extremely

flammable and the vapors are explosive. Serious personal

injury can occur when gasoline is spilled on yourself or

your clothes which can ignite. Wash your skin and change

clothes immediately.

a. Use only an approved gasoline container.

b. Never fill conta

iners inside a vehicle or on a truck

or trailer bed with a plastic liner. Always place contain-

ers on the ground away from your vehicle before filling.

c. When practical, remove gas-powered equipment from

the truck or trailer and refuel it on the ground. If this is

not possible, then refuel such equipment on a trailer

with a portable container, rather than from a gasoline

dispenser nozzle.

d. Keep the nozzle in contact with the rim of the fuel

tank or container opening at all times until fueling is

complete. Do not use a nozzle lock-open device.

Safe

Operation

Practices

This symbol points

out important safety

instructions which, if

not followed, could

endanger the personal

safety and/or property

of yourself and others.

Read and follow all

instructions in this man-

ual before attempting to

operate this machine.

Failure to comply with

these instructions

may result in personal

injury. When you see

this symbol, HEED ITS

WARNING.

Your

Responsibility

Restrict the use

of this power machine

to persons who read,

understand

and follow the warnings

and instructions

in this manual and on

the machine.

e. Extinguish all cigarettes, cigars, pipes and other

sources of ignition.

f. Never fuel machine indoors.

g. Never remove gas cap or add fuel while the engine

is hot or running. Allow engine to cool at least two

minutes before refueling.

h. Never over fill fuel tank. Fill tank to no more than ½

inch below bottom of filler neck to allow space for fuel

expansion.

i. Replace gasoline cap and tighten securely.

j. If gasoline is spilled, wipe it off the engine and equip-

ment. Move unit to another area. Wait 5 minutes before

starting the engine.

k. To reduce fire hazards, keep machine free of grass,

leaves, or other debris build-up. Clean up oil or fuel

spillage and remove any fuel soaked debris.

l. Never store the machine or fuel container inside where

there is an open flame, spark or pilot light as on a

water heater, space heater, furnace, clothes dryer or

other gas appliances.

m. Allow a machine to co

ol at least five minutes before

storing.

General Service

1. Never run an engine indoors or in a poorly ventilated

area. Engine exhaust contains carbon monoxide, an

odorless, and deadly gas.

2. Before cleaning, repairing, or inspecting, make certain the

blade(s) and all moving parts have stopped. Disconnect

the spark plug wire and ground against the engine to

prevent unintended starting.

3. Periodically check to make sure the blades come to

complete stop within approximately (5) five seconds after

operating the blade disengagement control. If the blades

do not stop within the this time frame, your unit should be

serviced professionally by an authorized Service Dealer.

4. Check brake operation frequently as it is subjected to wear

during normal operation. Adjust and service as required.

5. Check the blade(s) and engine mounting bolts at frequent

intervals for proper tightness. Also, visually inspect

blade(s) for damage (e.g., excessive wear, bent, cracked).

Replace the blade(s) with the original equipment manu-

facturer’s (O.E.M.) blade(s) only, listed in this manual.

“Use of parts which do not meet the original equipment

specifications may lead to improper performance and

compromise safety!”

6. Mower blades are sharp. Wrap the blade or wear gloves,

and use extra caution when servicing them.

7. Keep all nuts, bolts, and screws tight to be sure the

equipment is in safe working condition.

8. Never tamper with the safety interlock system or other

safety devices. Check their proper operation regularly.

9. After striking a foreign object, stop the engine, disconnect

the spark plug wire(s) and ground against the engine.

Thoroughly inspect the machine for any damage. Repair

the damage before starting and operating.

10. Never attempt to make adjustments or repairs to the

machine while the engine is running.

11. Grass catcher components and the discharge cover are

subject to wear and damage which could expose moving

parts or allow objects to be thrown. For safety protection,

frequently check components and replace immediately with

original equipment manufacturer’s (O.E.M.) parts only, listed

in this manual. “Use of parts which do not meet the original

equipment specifications may lead to improper performance

and compromise safety!”

12. Do not change the engine governor settings or over-speed

the engine. The governor controls the maximum safe

operating speed of the engine.

13. Maintain or replace safety and instruction labels, as neces-

sary.

14. Observe proper disposal laws and regulations for gas, oil,

etc. to pro

tect the environment.

15. According to the Consumer Products Safety Commission

(CPSC) and the U.S. Environmental Protection Agency

(EPA), this product has an Average Useful Life of seven (7)

years, or 270 hours of operation. At the end of the Average

Useful Life, have the machine inspected annually by an

authorized service dealer to ensure that all mechanical

and safety systems are working properly and not worn

excessively. Failure to do so can result in accidents, injuries

or death.

Spark Arrestor

Warning: This machine is equipped with

an internal combustion engine and should

not be used on or near any unimproved

forest-covered, brushcovered or grass-

covered land unless the engine’s exhaust

system is equipped with a spark arrester

meeting applicable local or provincial laws

(if any).

If a spark arrester is used, it should be maintained in effective

working order by the operator.

A spark arrester for the muffler is available through your nearest

engine authorized service dealer.

Do not modify engine

To avoid serious injury or death, do not modify engine in any

way. Tampering with the governor setting can lead to a runaway

engine and cause it to operate at unsafe speeds. Never tamper

with factory setting of engine governor.

Notice regarding Emissions

Engines which are certified to comply with California and

federal EPA emission regulations for SORE (Small Off Road

Equipment) are certified to operate on regular unleaded

gasoline, and may include the following emission control

systems: Engine Modification (EM) and Three Way Catalyst

(TWC) if so equipped.

Safe

Operation

Practices

This symbol points

out important safety

instructions which, if

not followed, could

endanger the personal

safety and/or property

of yourself and others.

Read and follow all

instructions in this man-

ual before attempting to

operate this machine.

Failure to comply with

these instructions

may result in personal

injury. When you see

this symbol, HEED ITS

WARNING.

Your

Responsibility

Restrict the use

of this power machine

to persons who read,

understand

and follow the warnings

and instructions

in this manual and on

the machine.

Safe

Symbols

This symbol points

out important safety

instructions which, if

not followed, could

endanger the personal

safety and/or property

of yourself and others.

Read and follow all

instructions in this man-

ual before attempting to

operate this machine.

Failure to comply with

these instructions

may result in personal

injury. When you see

this symbol, HEED ITS

WARNING.

Your

Responsibility

Restrict the use

of this power machine

to persons who read,

understand

and follow the warnings

and instructions

in this manual and on

the machine.

This page depicts and describes safety symbols that may appear on this product. Read, understand, and follow all instructions

on the machine before attempting to assemble and operate.

Symbol Description

READ THE OPERATOR’S MANUAL(S)

Read, understand, and follow all instructions in the manual(s) before attempting

to assemble and operate

DANGER— ROTATING BLADES

Never carry passengers. Never carry children, even with the blades off.

DANGER— ROTATING BLADES

Always look down and behind before and while backing to avoid a back-over

accident.

WARNING— ROTATING BLADES

Do not put hands or feet near rotating parts or under the cutting deck. Contact

with the blade(s) can amputate hands and feet.

WARNING—THROWN OBJECTS

This machine may pick up and throw and objects which can cause serious

personal injury.

WARNING—THROWN OBJECTS

This machine may pick up and throw and objects which can cause serious

personal injury.

BYSTANDERS

Keep bystanders, helpers, children and pets at least 75 feet from the machine

while it is in operation.

WARNING— SLOPE OPERATION

Do not operate this machine on a slope greater than 15 degrees.

WARNING— HOT SURFACE

Engine parts, especially the muffler, become extremely hot during operation. Allow

engine and muffler to cool before touching.

DANGER — ROTATING BLADES

To reduce the risk of injury, keep hands and feet away. Do not operate unless

discharge cover or grass catcher is in its proper place. If damaged, replace

immediately.

Setting Up

Your Lawn

Tractor

NOTE: This Operators

Manual covers a range

of product specifications

for various models.

Characteristics and

features discussed

and/or illustrated in

this manual may not be

applicable to all models.

MTD LLC reserves the

right to change product

specifications, designs

and equipment without

notice and without incur-

ring obligation.

WARNING

Use extreme care

when handling

gasoline. Gasoline is

extremely flammable

and the vapors are

explosive. Never fuel

machine indoors

or while the engine

is hot or running.

Extinguish cigarettes,

cigars, pipes, and

other sources of

ignition.

Gas and Oil Fill-up

The gasoline tank is located under the hood and has a

capacity of 1-1/2 gallons. Do not overfill.

WARNING: Use extreme care when

handling gasoline. Gasoline is ex-

tremely flammable and the vapors are

explosive. Never fuel machine indoors

or while the engine is hot or running.

Extinguish cigarettes, cigars, pipes, and

other sources of ignition.

Service the engine with gasoline and oil as instructed in

the separate Engine Operator/Owner Manual packed with

your tractor. Read instructions carefully.

IMPORTANT: Your tractor is shipped with motor oil in the

engine. However, you MUST check the oil level before

operating. Be careful not to overfill.

Shipping Brace Removal

WARNING: Make sure the riding

mower’s engine is off, remove the

ignition key, and set the parking brake

before removing the shipping brace.

• Locatetheshippingbrace,ifpresent,andaccompany-

ing warning tag found on the right side of the mower,

between the discharge chute and the cutting deck.

See Figure 3-2.

• Whileholdingthedischargechutewithyourlefthand,

remove the shipping brace with your right hand by

grasping it between your thumb and index finger and

rotating it clockwise.

WARNING: The shipping brace, used

for packaging purposes only, must be

removed and discarded before operat-

ing your riding mower.

WARNING: The mowing deck is capable

of throwing objects. Failure to operate

the riding mower without the discharge

cover in the proper operating position

could result in serious personal injury

and/or property damage.

Attaching The Steering Wheel

If the steering wheel for your tractor did not come

attached, the hardware for attaching it has been packed

within the steering wheel, beneath the steering wheel

cap. Carefully pry off the steering wheel cap and remove

the hardware.

NOTE: There are two different syles of steeering wheel

caps. Styles vary by model.

1. With the wheels of the tractor pointing straight

forward, place the steering wheel over the steering

shaft.

2. Place the washer (with the cupped side down) over

the steering shaft and secure with the hex bolt. See

Figure 3-3.

Figure 3-1

NOTE: This Operators Manual covers a range

of product specifications for various models.

Characteristics and features discussed and/or illustrated

in this manual may not be applicable to all models. MTD

LLC reserves the right to change product specifications,

designs and equipment without notice and without

incurring obligation.

Connecting the Battery Cables

CAUTION: When attaching battery

cables, always connect the POSITIVE

(Red) wire to its terminal first, followed

by the NEGATIVE (Black) wire.

For shipping reasons, both battery cables on your

equipment may have been left disconnected from the

terminals at the factory. To connect the battery cables,

proceed as follows:

NOTE: The positive battery terminal is marked Pos. (+).

The negative battery terminal is marked Neg. (–).

• Removetheplasticcover,ifpresent,fromthe

positive battery terminal and attach the red cable to

the positive battery terminal (+) with the bolt and hex

nut. See Fig. 3-1.

• Removetheplasticcover,ifpresent,fromthe

negative battery terminal and attach the black cable

to the negative battery terminal (–) with the bolt and

hex nut. See Fig. 3-1.

• Positiontheredrubberbootoverthepositivebattery

terminal to help protect it from corrosion.

NOTE: If the battery is put into service after the date

shown on top of battery, charge the battery as instructed

in the Maintenance section of this manual prior to

operating the tractor.

WARNING

Make sure the riding

mower’s engine is

off, remove the igni-

tion key, and set the

parking brake before

removing the shipping

brace.

Setting Up

Your Lawn

Tractor

The shipping brace,

used for packaging

purposes only, must

be removed and

discarded before

operating your riding

mower.

The mowing deck is

capable of throwing

objects. Failure to

operate the riding

mower without the

discharge cover in

the proper operating

position could result

in serious personal

injury and/or property

damage.

3. Place the steering wheel cap over the center of the

steering wheel and push downward until it “clicks” into

place.

IMPORTANT: Do NOT overtighten.

Figure 3-2

Figure 3-3

Figure 3-4

Attaching the Hood Scoop

If so equipped)

If the hood scoop was not secured to the hood of your

tractor at the factory, you will find it in a plastic bag,

hanging from the throttle lever.

To install:

1. Carefully pivot the tractor hood forward.

2. Remove the four screws from the underside of the

hood scoop.

3. Line up the four holes in the hood scoop with the

four holes visible through the tractor’s hood louvres.

See Figure 3-4.

4. Whileholdingthescoopinplace,usea3/8”socket

wrench (or box wrench) to carefully tighten the scoop

onto the hood. Do NOT overtighten.

Setting Up

Your Lawn

Tractor

For shipping reasons,

seats are either

fastened to the tractor

seat’s pivot bracket

with a plastic tie, or

mounted backward to

the pivot bracket. In

either case, free the

seat form its shipping

position and remove

the two hex screws

(or knobs, on models

so equipped) from the

bottom of seat before

proceeding with ap-

plicable instructions.

WARNING

Before operating this

machine, make sure

the seat is engaged in

the seat stop, stand

behind the machine

and pull back on seat

until fully engaged

into stop.

Figure 3-5

Figure 3-6

Attaching The Seat

If the seat for your tractor did not come attached, refer

to Figure 3-5, Figure 3-6, and Figure 3-7 to identify your

tractor’s seat style and follow the applicable instructions

below to attach it.

NOTE: For shipping reasons, seats are either fastened

to the tractor seat’s pivot bracket with a plastic tie, or

mounted backward to the pivot bracket. In either case,

free the seat form its shipping position and remove the

hex screw (or knob) from the bottom of seat before

proceeding with applicable instructions below.

1. Position the shoulder screws (found on the base of

the seat) inside the slot openings in the seat pivot

bracket. Figure 3-5 or Figure 3-6.

2. Slide the seat slightly rearward in the seat pivot

bracket, lining up the rear slots in the pivot bracket

with the remaining two holes in the seat’s base.

3. Select desired position for the seat, and secure with

the hex screw (See Figure 3-5) or knob (See Figure

3-6) removed earlier.

4. To adjust the position of the seat, loosen the hex

screw (or knob if equipped) on the bottom of the

seat. Slide the seat forward or backward as desired.

Retighten the screw (or knob).

Tire Pressure

WARNING: Maximum tire pressure un-

der any circumstances is 30 psi. Equal

tire pressure should be maintained at

all times.

The tires on your unit may be over-inflated for shipping

purposes. Reduce the tire pressure before operating

the tractor. Recommended operating tire pressure is

approximately 10 p.s.i for the rear tires & 14 p.s.i. for the

front tires. Check sidewall of tire for maximum p.s.i

WARNING

Setting Up

Your Lawn

Tractor

Figure 3-7

Maximum tire pres-

sure under any

circumstances is 30

psi. Equal tire pressure

should be maintained

at all times.

Identifying the Mulch Plug (if so

equipped)

On tractor models so equipped, a mulch plug can either

be found within the cutting deck’s discharge opening or

packed separately with your unit.

NOTE: Refer to Mulching in the Operation section of this

manual for more detailed information.

If you’d prefer to operate the cutting deck without mulch-

ing, simply remove the mulch plug by unthreading the

plastic wing nut which fastens it to the cutting deck. This

will allow the clippings to discharge out of the discharge

opening during operation. See Figure 3-7.

Setting the Deck Gauge Wheels

(if so equipped)

Move the tractor on a firm and level surface, preferably

pavement, and proceed as follows

1. Select the height position of the cutting deck by plac-

ing the deck lift lever in the normally desired mowing

height setting (any of the six different cutting height

notches on the right fender).

2. Check the gauge wheels for contact or excessive

clearance with the surface below. The deck gauge

wheels should have between ¼-inch and ½-inch

clearance above the ground as follows:

If the gauge wheels have excessive clearance or contact

with the surface, adjust as follows:

a. Raise the deck lift handle to its highest setting.

b. Remove the gauge wheels by removing the lock

nuts and shoulder screws which secure them to

thedeck.SeeFig.3-8.

c. Place the deck lift lever in the desired mowing

height setting.

d. Reinsert the shoulder screw (with each gauge

wheel) into the index hole that leaves approxi-

mately ½-inch between the bottom of the wheel

and the pavement.

Refer to Leveling the Deck in the Maintenance section

of this manual for more detailed instructions regarding

various deck adjustments.

Figure 3-8

Operating

Your Lawn

Tractor

Know Your Lawn Tractor

Figure 4-1

A Speed Control Lever E Throttle/Choke Lever

B Brake Pedal F Ignition Switch Module †

C Parking Brake Lever G Deck Lift Lever

D Choke Control† H PTO (Blade Engage) Lever

WARNING: Read and follow all safety rules and instructions in this manual, including the entire

Operation section, before attempting to operate this machine. Failure to comply with all safety rules and

instructions may rerult in personal injury.

† If so equipped

NOTE: Any reference

in this manual to the

RIGHT or LEFT side of

the tractor is observed

from operator’s position.

NOTE: Steering wheel not shown for clarity

For shipping reasons,

seats are either

fastened to the tractor

seat’s pivot bracket

with a plastic tie, or

mounted backward to

the pivot bracket. In

either case, free the

seat form its shipping

position and remove

the two hex screws

(or knobs, on models

so equipped) from the

bottom of seat before

proceeding with ap-

plicable instructions.

H g

Operating

Your Lawn

Tractor

WARNING

Never leave a running

machine unattended.

Always disengage

PTO, move speed con-

trol lever into neutral

position, set parking

brake, stop engine and

remove key to prevent

unintended starting.

Throttle Control Lever

The throttle control lever is located on the right side of

the tractor’s dash panel. This lever controls the speed

of the engine and, on some models, when pushed all

the way forward, the choke control also. When set in a

given position, the throttle will maintain a uniform engine

speed. See Figure 4-2.

IMPORTANT: When operating the tractor with the cutting

deck engaged, be certain that the throttle lever is always

in the FAST (rabbit) position.

Choke Control

On some models, moving the

throttle lever all the way forward

activates the engine’s choke

control. On all other models, the

choke control can be found on

the left side of the dash panel

and is activated by pulling the

knob outward. Activating the

choke control closes the choke

plate on the carburetor and aids

in starting the engine. Refer to Starting The Engine in

the OPERATING section manual for detailed starting

instructions.

Ignition Switch

The ignition switch is activated to start the engine. Insert

key into the ignition switch and turn clockwise to the

START position. Release the key into the ON position

once engine has fired.

To stop the engine, turn the ignition key counterclockwise

to the OFF position.

Figure 4-3A - The headlights are on when the engine is

running.

Figure 4-3B - To activate the headlights, turn the key one

more position to the left. The engine will continue to run

with the headlights on.

Ignition Switch Module

(If Equipped)

To start the engine, insert the key into the ignition switch

and turn clockwise to the START position. Release the

key into the NORMAL MOWING MODE position once

the engine has fired.

To stop the engine, turn the ignition key counterclockwise

to the OFF position. See Figure 4-3C.

WARNING: Never leave a running

machine unattended. Always disengage

PTO, move shift lever into neutral

position, set parking brake, stop engine

and remove key to prevent unintended

starting.

IMPORTANT: Prior to operating the tractor, refer to both

Safety Interlock Switches and Starting The Engine

in the OPERATING section of this manual for detailed

instructions regarding the Ignition Switch Module and

operating the tractor in REVERSE CAUTION MODE.

&!34

3,/7

#(/+%

&!34

3,/7

Figure 4-2

Start

Position

Stop

Position

Normal

Mowing

Mode

Off

Start

Off

On/Lights

STOP

Figure 4-3

IMPORTANT

Prior to operating the

tractor, refer to both

Safety Interlock

Switches on page

14 and Starting The

Engine on page 16

of this manual for

detailed instructions

regarding the Ignition

Switch Module and

operating the tractor in

REVERSE CAUTION

MODE.

Speed Control Lever

The speed control lever, located on the left fender,

allows you to regulate the travel direction and ground

speed of the lawn tractor. To use, release the parking

brake and move the speed control lever forward (to

travel forward) or rearward (to travel in reverse). The

further forward or rearward that the lever is moved, the

faster the tractor will travel. See Figure 4-4.

Place the speed control lever in the Cutting Speed, or

slower, position when mowing.

IMPORTANT: Do NOT attempt to change the direction

of travel when the tractor is in motion. Serious damage

to the tractor’s transmission could result. Always bring

the tractor to a complete stop before moving the speed

control lever from forward to reverse or vice versa.

IMPORTANT: Always set the parking brake when

leaving the tractor unattended.

Deck Lift Lever

Found on your tractor’s right fender, the deck lift lever is

used to change the height of the cutting deck. To use,

move the lever to the left, then place in the notch best

suited for your application.

Brake Pedal

The brake pedal is located on the left side of the lawn

tractor, along the running board. Depress the brake

pedal part way down to slow the tractors ground speed.

Depress the pedal all the way down to engage the disc

brake and bring the tractor to a complete stop.

NOTE: The pedal must be depressed to start the

engine. Refer to Safety Interlock Switches on page 14.

Parking Brake

To set the parking brake, fully depress the brake pedal.

Move the speed control lever all the way down and into

the parking brake position. Release the brake pedal to

allow the parking brake to engage.

To release the parking brake, depress the brake pedal

and move the speed control lever out of the notches to

the desired position. Release the speed control lever

and the brake pedal.

NOTE: The parking brake must be set if the operator

leaves the seat with the engine running or the engine will

automatically shut off.

PTO (Blade Engage) Lever

Found on the tractor’s right fender, the PTO (blade

engage) lever is used to engage power to the cutting

deck or other (separately available) attachments. To

operate, move the lever all the way forward. Moving the

lever all the way rearward into the PTO OFF position

disengages power to the cutting deck/ attachment.

NOTE: The PTO (blade engage) lever must be in the

disengaged (PTO OFF) position when starting the

engine.

Operating

Your Lawn

Tractor

Safety Interlock Switches

This tractor is equipped with a safety interlock system

for the protection of the operator. If the interlock system

should ever malfunction, do not operate the tractor.

Contact an authorized MTD service dealer.

• Thesafetyinterlocksystempreventstheengine

from cranking or starting unless the parking brake

is engaged, and the PTO (Blade Engage) lever (or

button) is in the disengaged (OFF) position.

• Theenginewillautomaticallyshutoffiftheoperator

leaves the seat before engaging the parking brake.

• Theenginewillautomaticallyshutoffiftheoperator

leaves the tractor’s seat with the PTO (Blade Engage)

lever in the engaged (ON) position, regardless of

whether the parking brake is engaged.

• Theenginewillautomaticallyshutoffiftheoperator

engages the PTO with the parking brake ON.

Models without Reverse Caution Mode

• TheenginewillautomaticallyshutoffifthePTO(Blade

Engage) lever is moved into the engaged (ON) position

with the shift lever in Reverse.

Models with Reverse Caution Mode

• WiththeignitionkeyintheNORMAL MOWING posi-

tion, the engine will automatically shut off if the PTO

(Blade Engage) lever is moved into the engaged (ON)

position with the shift lever in Reverse.

WARNING: Do not operate the tractor if

the interlock system is malfunctioning.

This system was designed for your safety

and protection.

NOTE: The PTO (Blade

Engage) lever must be

in the disengaged (PTO

OFF) position when

starting the engine.

Figure 4-4

NOTE: The parking

brake must be set if the

operator leaves the seat

with the engine run-

ning or the engine will

automatically shut off.

IMPORTANT

Never force the shift

lever. Doing so may

result in serious

damage to the tractor’s

transmission.

Do not operate

the tractor if the

interlock system is

malfunctioning. This

system was designed

for your safety and

protection.

WARNING

Operating

Your Lawn

Tractor

Reverse Caution Mode (If Equipped)

WARNING: Use extreme caution while

operating the tractor in the REVERSE

CAUTION MODE. Always look down and

behind before and while backing. Do

not operate the tractor when children

or others are around. Stop the tractor

immediately if someone enters the

area.

The REVERSE CAUTION MODE position of the key

switch module allows the tractor to be operated in

reverse with the blades (PTO) engaged.

IMPORTANT: Mowing in reverse is not recommended.

To use the REVERSE CAUTION MODE:

IMPORTANT: The operator MUST be seated in the

tractor seat.

1. Start the engine as instructed on page 16 under

Starting The Engine.

2. Turn the key from the NORMAL MOWING (Green)

position to the REVERSE CAUTION MODE (Yellow)

position of the key switch module. See Figure 4-5.

3. Depress the REVERSE PUSH BUTTON (Orange,

Triangular Button) at the top, right corner of the key

switch module. The red indicator light at the top, left

corner of the key switch module will be ON while

activated. See Figure 4-5.

4. Once activated (indicator light ON), the tractor can

be driven in reverse with the cutting blades (PTO)

engaged.

5. Always look down and behind before and while

backing to make sure no children are around.

6. After resuming forward motion, return the key to the

NORMAL MOWING position.

IMPORTANT: The REVERSE CAUTION MODE will

remain activated until:

a. The key is placed in either the NORMAL MOWING

position or STOP position.

b. The operator engages the parking brake by fully

depressing the brake pedal and holding it down

while moving the speed control lever into the PARK

BRAKE position.

Engaging the Parking Brake

To engage the parking brake:

1. Fully depress the brake pedal and hold it down with

your foot.

2. Move the parking brake lever all the way down and

into the parking brake position.

3. Release the brake pedal to allow the parking brake to

engage.

To release the parking brake:

1. Depress the brake pedal and move the speed control

lever out of the parking brake position and into a

desired speed.

Setting the Cutting Height

1. Select the height position of the cutting deck by

placing the deck lift lever in any of the different cutting

height notches on the right side of the fender.

2. Adjust the deck wheels, if equipped, so that they are

between ¼-inch and ½-inch above the ground when the

tractor is on a smooth, flat surface such as a driveway.

WARNING: Keep hands and feet away

from the discharge opening of the

cutting deck.

NOTE: On models so equipped, the deck wheels are an

anti-scalp feature of the deck and are not designed to

support the weight of the cutting deck.

Refer to Leveling the Deck in the Adjustment section

of this manual for more detailed instructions regarding

various deck adjustments.

Starting the Engine

WARNING: Do not operate the tractor if

the interlock system is malfunctioning.

This system was designed for your

safety and protection.

NOTE: Refer to the TRACTOR SET-UP on page 8 of this

manual for Gasoline and Oil fill-up instructions.

1. Insert the tractor key into the ignition switch.

2. Place the PTO (Blade Engage) lever in the disen-

gaged (OFF) position.

3. Engage the tractor’s parking brake.

4. Activate the choke control.

5. Turn the ignition key clockwise to the START position.

After the engine starts, release the key. It will return to

the ON position.

WARNING

Do not operate

the tractor if the

interlock system is

malfunctioning. This

system was designed

for your safety and

protection.

Use extreme caution

while operating

the tractor in the

REVERSE CAUTION

MODE. Always look

down and behind

before and while

backing. Do not

operate the tractor

when children or

others are around.

Stop the tractor

immediately if

someone enters the

area.

3TART

0OSITION

3TOP

0OSITION

2EVERSE

0USH"UTTON

2EVERSE

#AUTION-ODE

0OSITION

)NDICATOR

,IGHT

Figure 4-5

Keep hands and

feet away from the

discharge opening of

the cutting deck.

Operating

Your Lawn

Tractor

If you strike a foreign

object, stop the

engine, disconnect the

spark plug wire(s) and

ground against the

engine. Thoroughly

inspect the machine

for any damage.

Repair the damage

before restarting and

operating.

Avoid sudden starts,

ex-cessive speed and

sudden stops.

Do not leave the seat

of the tractor without

first placing the PTO

(Blade Engage) lever

in the disengaged

(OFF) position,

depressing the brake

pedal and engaging

the parking brake. If

leaving the tractor

unattended, also turn

the ignition key off

and remove the key.

IMPORTANT: Do NOT hold the key in the START

position for longer than ten seconds at a time. Doing so

may cause damage to your engine’s electric starter.

6. After the engine starts, deactivate the choke control

and place the throttle control in the FAST position.

NOTE: Do NOT leave the choke control on while operat-

ing the tractor. Doing so will result in a “rich” fuel mixture

and cause the engine to run poorly.

Stopping the Engine

WARNING: If you strike a foreign

object, stop the engine, disconnect the

spark plug wire(s) and ground against

the engine. Thoroughly inspect the

machine for any damage. Repair the

damage before restarting and operat-

ing the tractor.

1. If the blades are engaged, place the PTO (Blade

Engage) lever in the disengaged (OFF) position.

2. Turn the ignition key counterclockwise to the STOP

position.

3. Remove the key from the ignition switch to prevent

unintended starting.

Driving The Tractor

WARNING: Avoid sudden starts,

ex-cessive speed and sudden stops.

WARNING: Do not leave the seat

of the tractor without first placing

the PTO (Blade Engage) lever in the

disengaged (OFF) position, depress-

ing the brake pedal and engaging the

parking brake. If leaving the tractor

unattended, also turn the ignition key

off and remove the key.

WARNING: Always look down and

behind before and while backing up to

avoid a back-over accident.

1. Move the throttle lever into the FAST (rabbit) posi-

tion.

NOTE: Always operate the tractor with the throttle

control lever in the FAST (rabbit) position for the most

efficient use of the cutting deck or other (separately

available) attachments.

2. Release the parking brake by depressing the brake

pedal.

3. Position the speed control lever in desired position.

The further forward or rearward that the lever is

moved, the faster the tractor will travel.

WARNING

AVOID SERIOUS INJURY OR

DEATH

• GOUPANDDOWNSLOPES,NOTACROSS.

• AVOIDSUDDENTURNS.

• DONOTOPERATETHEUNITWHEREITCOULDSLIPORTIP.

• IFMACHINESTOPSGOINGUPHILL,STOPBLADE(S)AND

BACK DOWNHILL SLOWLY.

• DONOTMOWWHENCHILDRENOROTHERSAREAROUND.

• NEVERCARRYCHILDREN,EVENWITHBLADESOFF.

• LOOKDOWNANDBEHINDBEFOREANDWHILEBACKING.

• KEEPSAFETYDEVICES(GUARDS,SHIELDS,AND

SWITCHES) IN PLACE AND WORKING.

• REMOVEOBJECTSTHATCOULDBETHROWNBYTHE

BLADE(S).

• KNOWLOCATIONANDFUNCTIONOFALLCONTROLS.

• BESUREBLADE(S)ANDENGINEARESTOPPEDBEFORE

PLACING HANDS OR FEET NEAR BLADE(S).

• BEFORELEAVINGOPERATOR’SPOSITION,DISENGAGE

BLADE(S), PLACE THE SHIFT LEVER IN NEUTRAL, ENGAGE

BRAKE LOCK, SHUT ENGINE OFF AND REMOVE KEY.

READ OPERATOR’S MANUAL

WARNING: Do NOT attempt to change

the direction of travel when the tractor is

in motion. Always bring the tractor to a

complete stop before moving the speed

control lever from forward to reverse or

vice versa. Failure to do so could result

in serious damage to your tractor’s

transmission.

IMPORTANT: First-time operators should use slower

speeds. Become completely familiar with the tractor’s

operation and controls before operating the tractor at

higher speeds.

4. The lawn tractor is brought to a stop by depressing the

clutch-brake pedal.

5. Set the parking brake by fully depressing the brake

pedal and keeping it depressed while placing the

parking brake lever in the ON position. Release the

brake pedal to allow the parking brake to engage.

WARNING: Before leaving the operator’s

position for any reason, disengage the

blades, place the shift lever in neutral,

engage the parking brake, shut engine

off and remove the key.

IMPORTANT: When stopping the tractor for any reason

while on a grass surface, always:

1. Place the speed control lever in neutral,

2. Engage the parking brake,

WARNING

Operating

Your Lawn

Tractor

WARNING

3. Shut engine off and remove the key. Doing so

will minimize the possibility of having your lawn

‘‘browned’’ by hot exhaust from your tractor’s running

engine.

Driving On Slopes

Refer to the SLOPE GAUGE on page 3 to help determine

slopes where you may operate the tractor safely.

WARNING: Do not mow on inclines with

a slope in excess of 15 degrees (a rise of

approximately 2-1/2 feet every 10 feet).

The tractor could overturn and cause

serious injury.

• Mowupanddownslopes,NEVERacross.

• Exerciseextremecautionwhenchangingdirectionon

slopes.

• Watchforholes,ruts,bumps,rocks,orotherhidden

objects. Uneven terrain could overturn the machine.

Tall grass can hide obstacles.

• Avoidturnswhendrivingonaslope.Ifaturnmustbe

made, turn down the slope. Turning up a slope greatly

increases the chance of a roll over.

• Avoidstoppingwhendrivingupaslope.Ifitis

necessary to stop while driving up a slope, start up

smoothly and carefully to reduce the possibility of

flipping the tractor over backward.

Engaging the Blades

Engaging the PTO (Blade Engage) transfers power to the

cutting deck or other (separately available) attachments.

To engage the blades, proceed as follows:

1. Move the throttle control lever to the FAST (rabbit)

position.

2. Grasp the PTO (Blade Engage) lever and pivot it all

the way forward into the engaged (ON) position.

3. Keep the throttle lever in the FAST (rabbit) position

for the most efficient use of the cutting deck or other

(separately available) attachments

IMPORTANT: Models with Reverse Caution Mode:

The engine will automatically shut off if the PTO is

engaged with the shift lever in position for reverse travel

with the ignition key in the NORMAL MOWING position.

Models without Reverse Caution Mode:

The PTO (Blade Engage) lever must be in the disen-

gaged (OFF) position when starting the engine, when

traveling in reverse, and if the operator leaves the seat.

Refer to Safety Interlock Switches on page 14.

Using the Deck Lift Lever

To raise the cutting deck, move the deck lift lever to

the left, then place it in the notch best suited for your

application. Refer to Setting The Cutting Height earlier in

this section.

Mowing

WARNING: To help avoid blade contact

or a thrown object injury, keep bystand-

ers, helpers, children and pets at least

75 feet from the machine while it is

in operation. Stop machine if anyone

enters the area.

The following information will be helpful when using the

cutting deck with your tractor:

WARNING: Plan your mowing pattern

to avoid discharge of materials toward

roads, sidewalks, bystanders and the

like. Also, avoid discharging material

against a wall or obstruction which may

cause discharged material to ricochet

back toward the operator.

• Donotmowathighgroundspeed,especiallyifa

mulch kit or grass collector is installed.

• Forbestresultsitisrecommendedthatthefirsttwo

laps be cut with the discharge thrown towards the

center. After the first two laps, reverse the direction to

throw the discharge to the outside for the balance of

cutting. This will give a better appearance to the lawn.

• Donotcutthegrasstooshort.Shortgrassinvites

weed growth and yellows quickly in dry weather.

• Mowingshouldalwaysbedonewiththeengineatfull

throttle.

• Underheavierconditionsitmaybenecessarytogo

back over the cut area a second time to get a clean

cut.

• DoNOTattempttomowheavybrushandweedsand

extremely tall grass. Your tractor is designed to mow

lawns, NOT clear brush.

• Keepthebladessharpandreplacethebladeswhen

worn. Refer to Cutting Blades on page 25 of this

manual for proper blade sharpening instructions.

Mulching (If Equipped)

Select models come equipped with a mulch kit which

incorporates special blades, already standard on the

tractor, in a process of recirculating grass clippings

repeatedly beneath the cutting deck. The ultra-fine

clippings are then forced back into the lawn where they

act as a natural fertilizer.

Observe the following points for the best results when

mulching:

• Neverattempttomulchifthelawnisdamp.Wetgrass

tends to stick to the underside of the cutting deck

preventing proper mulching of the clippings.

• DoNOTattempttomulchmorethan1/3thetotal

height of the grass or approximately 1-1/2 inches.

Doing so will cause the clippings to clump up beneath

the deck and not be mulched effectively.

Do not mow on in-

clines with a slope in

excess of 15 degrees

(a rise of approxi-

mately 2-1/2 feet every

10 feet). The tractor

could overturn and

cause serious injury.

Always look down

and behind before

and while backing up

to avoid a back-over

accident.

• Maintainaslowgroundspeedtoallowthegrass

clippings more time to effectively be mulched.

• AlwayspositionthethrottlecontrolleverintheFAST

(rabbit) position and allow it to remain there while

mowing. Failing to keep the engine at full throttle

places strain on the tractor’s engine and does not

allow the blades to properly mulch grass.

NOTE: It is not necessary to remove the discharge

chute to operate the mower with the mulch kit installed.

To operate the cutting deck without mulching, simply

remove the mulch plug by unthreading the plastic wing

nut which fastens it to the cutting deck. This will allow

the clippings to discharge out the side. See Figure 4-6.

Moving the Tractor Manually

Your tractor’s transmission is equipped with a hydro-

static relief valve for occasions when it is necessary to

move the tractor manually. Activating this valve forces

the fluid in the transmission to bypass its normal route,

allowing the rear tires to “freewheel.” To engage the

hydrostatic relief valve, proceed as follows:

• Locatethehydrostaticbypassrodintherearofthe

tractor. See Figure 4-7.

• Pullthehydrostaticbypassrodoutward,thendown,

to lock it in place.

NOTE: The transmission will NOT engage when the

hydrostatic bypass rod is pulled out. Return the rod to its

normal position prior to operating the tractor.

IMPORTANT: Never attempt to move the tractor manu-

ally without first engaging the hydrostatic relief valve.

Doing so will result in serious damage to the tractor’s

transmission.

Headlights

• Onsomemodels,thelampsareONwheneverthe

tractor’s engine is running. On other models, the

lamps are ON whenever the ignition key is moved out

of the STOP position.

• Onallmodels,thelampsturnOFFwhentheignition

key is moved to the STOP position.

Figure 4-6

WARNING

Plan your mowing

pattern to avoid

discharge of materi-

als toward roads,

sidewalks, bystanders

and the like. Also,

avoid discharging

material against a

wall or obstruction

which may cause

discharged material to

ricochet back toward

the operator.

NOTE: This Operators

Manual covers a range

of product specifica-

tions for various

models. Characteristics

and features discussed

and/or illustrated in

this manual may not be

applicable to all models.

MTD LLC reserves the

right to change product

specifications, designs

and equipment without

notice and without

incurring obligation.

Operating

Your Lawn

Tractor

Figure 4-7

Adjusting

Your Lawn

Tractor

Figure 5-2 (42” Deck)

Figure 5-1 (38” & 46” Deck)

WARNING

Never attempt to

make any adjust-

ments while the

engine is running,

except where speci-

fied in the operator’s

manual.

WARNING: Never attempt to make

any adjustments while the engine is

running, except where specified in the

operator’s manual.

Leveling the Deck

NOTE: Check the tractor’s tire pressure before perform-

ing any deck leveling adjustments. Refer to Tires on page

24 for information regarding tire pressure.

Front To Rear

The front of the cutting deck is supported by a stabilizer

bar that can adjusted to level the deck from front to rear.

The front of the deck should be between 1/4-inch and

3/8-inch lower than the rear of the deck. Adjust if neces-

sary as follows:

1. With the tractor parked on a firm, level surface, place

the deck lift lever in the top notch (highest position)

and rotate the blade nearest the discharge chute so

that it is parallel with the tractor.

2. Measure the distance from the front of the blade tip to

the ground and the rear of the blade tip to the ground.

The first measurement taken should be between

1/4” and 3/8” less than the second measurement.

Determine the approximate distance necessary for

proper adjustment and proceed, if necessary, to the

next step.

3. Locate the jam nut and lock nut on the front side of the

stabilizer bracket. See Figure 5-1 or Figure 5-2. After

loosening the jam nut:

Tighten the lock nut to raise the front of the deck;

Loosen the lock nut to lower the front of the deck.

4. Retighten the jam nut loosened earlier when proper

adjustment is achieved.

Side to Side

If the cutting deck appears to be mowing unevenly, a side

to side adjustment can be performed. Adjust if necessary

as follows:

1. With the tractor parked on a firm, level surface, place

the deck lift lever in the top notch (highest position)

and rotate both blades so that they are perpendicular

with the tractor.

2. Measure the distance from the outside of the left blade

tip to the ground and the distance from the outside of

the right blade tip to the ground. Both measurements

taken should be equal. If they’re not, proceed to the

next step.

3. Loosen, but do NOT remove, the hex cap screw on

the left deck hanger bracket. See Figure 5-3.

4. Balance the deck by using a wrench to turn the

adjustment gear (found immediately behind the hex

cap screw just loosened) clockwise/up or counter-

clockwise/down. The deck is properly balanced when

both blade tip measurements taken earlier are equal.

5. Retighten the hex cap screw on the left deck hanger

bracket when proper adjustment is achieved.

Parking Brake Adjustment

WARNING: Never attempt to adjust the

brakes while the engine is running.

Always disengage PTO, move shift

lever into neutral position, stop engine

and remove key to prevent unintended

starting.

If the tractor does not come to a complete stop when the

brake pedal is completely depressed, or if the tractor’s

rear wheels can roll with the parking brake applied,

the brake is in need of adjustment. See an authorized

service dealer to have your brakes properly adjusted.

Never attempt to

adjust the brakes

while the engine

is running. Always

disengage PTO, move

shift lever into neutral

position, stop engine

and remove key to

prevent unintended

starting.

Figure 5-3

Refer to the Set-Up

section of this manual

for seat adjustment

instructions.

WARNING: Before performing any

maintenance or repairs, disengage

PTO, move shift lever into neutral posi-

tion, set parking brake, stop engine

and remove key to prevent unintended

starting.

Engine

Refer to the Engine Operator/Owner Manual for

engine maintenance instructions.

Check engine oil level before each use as instructed

in the Engine Operator/Owner Manual packed with your

unit. Follow the instructions carefully.

Changing Engine Oil and Filter

NOTE: Depending on the engine model found on your

tractor, it may be necessary to remove the tractor’s side

panel in order to replace the oil filter (if so equipped).

For draining oil from the engine’s crankcase of select

model tractors, a plastic oil drain sleeve or hose is

packed with this Operator’s Manual. See Figure 6-1.

1. Change the oil as instructed in the separate Engine

Operator/Owner Manual packed with your unit.

2. Service the oil filter (if so equipped) as instructed in

the separate Engine Operator/Owner Manual packed

with your unit.

3. Refill the engine with the proper quantity and weight

of new motor oil as instructed in the Engine Opera-

tor/Owner Manual packed with your unit.

Air Cleaner

Service the pre-cleaner, if so equipped, and cartridge/air

cleaner element as instructed in the Engine Operator/

Owner Manual packed with your unit.

Spark Plug(s)

The spark plug(s) should be cleaned and the gap reset

once a season. Spark plug replacement is recom-

mended at the start of each mowing season. Refer to

the Engine Operator/Owner Manual for correct plug type

and gap specifications.

Maintaining

Your Lawn

Tractor

NOTE: Depending on

the engine model found

on your tractor, it may

be necessary to remove

the tractor’s side panel

in order to replace the

oil filter (if so equipped)

Figure 6-2

Figure 6-1

Lubrication

WARNING: Before lubricating, repairing,

or inspecting, always disengage PTO,

move shift lever into neutral position, set

parking brake, stop engine and remove

key to prevent unintended starting.

Engine

Lubricate the engine with motor oil as instructed in the

Engine Owner Manual packed with your unit.

Pivot Points & Linkage

Lubricate all the pivot points on the drive system, parking

brake and lift linkage at least once a season with light oil.

Rear Wheels

The rear wheels should be removed from the axles once

a season. Lubricate the axles and the rims well with an

all-purpose grease before re-installing them.

Front Axles

Each end of the tractor’s front pivot bar may be equipped

with a grease fitting. Lubricate with a grease gun after

every 25 hours of tractor operation.

Cleaning the Engine And Deck

Any fuel or oil spilled on the machine should be wiped

off promptly. Do NOT allow debris to accumulate around

the cooling fins of the engine or on any other part of the

machine.

IMPORTANT: The use of a pressure washer to clean your

tractor is NOT recommended. It may cause damage to

electrical components, spindles, pulleys, bearings or the

engine.

A hex plug can be found on your tractor’s 42” & 46” deck

surface. See Figure 6-2.

This plug can be replaced with a water port to be used as

part of a separately-available deck wash system.

WARNING

Before performing

any maintenance or

repairs, disengage

PTO, move shift lever

into neutral position,

set parking brake,

stop engine and

remove key to prevent

unintended starting.

NOTE: Refer to page 28 for information regarding this and

other separately-available attachments & accessories for

your tractor.

La page charge ...

Bolens 13AX79GH565 Le manuel du propriétaire

Marque: Bolens

Modèle: 13AX79GH565

Catégorie: Tondeuses à gazon

Taper: Le manuel du propriétaire

Ce manuel convient également à

13AN79GG565

Télécharger le PDF

rapport

dans d''autres langues

English: Bolens 13AX79GH565 Owner's manual

Bolens 13AX79GH565 Le manuel du propriétaire

Ce manuel convient également à

Bolens 13AX79GH565 Le manuel du propriétaire

dans d''autres langues

Autres documents