Toro LX500 Lawn Tractor Manuel utilisateur

Marque: Toro

Modèle: LX500 Lawn Tractor

Catégorie: Tondeuses à gazon

Taper: Manuel utilisateur

LX500 Lawn Tractor

Model No. 13AP60RP544

launaM s’rotarep

772C0850

01/06

Form Number 3355-979 Rev A

TABLE OF CONTENTS

FINDING MODEL NUMBER

This Operator’s Manual is an important part of your new lawn tractor. It will help you assemble, prepare and maintain

the unit for best performance. Please read and understand what it says.

Before you start assembling your new equipment, please locate the model plate on the

uipment and copy the information from it in the space provided below. A sample model plate is

also

illustrated below. You can locate the moel plate by looking at the underside of the tractor’s seat.

This

information will be necessary to use the manufacturer’s web site and/or help from a Toro

Service Dealer.

CUSTOMER SUPPORT

Please do NOT return the unit to the retailer without first contacting Customer Support.

you have difficulty assembling this product or have any questions regarding the controls, operation or maintenance

of this unit, you can seek help from the experts. Choose from the options below:

Con

tent Page

Important Safe Operation Practices 3

Slope Gauge 7

actor Set-Up 8

Know Your Lawn Tractor 10

Operating Your Lawn Mower 14

Making Adjustments 18

Maintaining Your Lawn Tractor 20

Service

Off-Season Storage 24

Maintenance Chart

Troubleshooting 25

Specifications 27

Warranty Information 28

Content Page

MODEL NUMBER SERIAL NUMBER DOM

THE TORO COMPANY

8111

LYNDALE AVE. SOUTH

BLOOMING

TON, MINNESOTA 55420-1196

TOLL FREE PHONE NUMBER: 1-888-384-9942 USA

TOLL FREE PHONE NUMBER: 1-888-848-4073 Canada

Copy the model number here:

Cop

y the serial number here:

SECTION 1: IMPORTANT SAFE OPERATION PRACTICES

WARNING: This symbol points out important safety instructions which, if not followed, could endanger

the personal safety and/or property of yourself and others. Read and follow all instructions in this manual

before attempting to operate this machine. Failure to comply with these instructions may result in personal

injury. When you see this symbol—heed its warning.

DANGER: This machine was built to be operated according to the rules for safe operation in this man-

ual. As with any type of power equipment, carelessness or error on the part of the operator can result in

serious injury. This machine is capable of amputating hands and feet and throwing objects. Failure to

observe the following safety instructions could result in serious injury or death.

GENERAL OPERATION

1. Read, understand, and follow all instructions on the

machine and in the manual(s) before attempting to

assemble and operate. Keep this manual in a safe

place for future and regular reference and for

ordering replacement parts.

2. Be familiar with all controls and their proper

operation. Know how to stop the machine and

disengage them quickly.

3. Never allow children under 14 years old to operate

this machine. Children 14 years old and over

should read and understand the operation

instructions and safety rules in this manual and

should be trained and supervised by a parent.

4. Never allow adults to operate this machine without

proper instruction.

5. To help avoid blade contact or a thrown object

injury, keep bystanders, helpers, children and pets

at least 75 feet from the machine while it is in

operation. Stop machine if anyone enters the area.

6. Thoroughly inspect the area where the equipment

is to be used. Remove all stones, sticks, wire,

bones, toys, and other foreign objects which could

be picked up and thrown by the blade(s). Thrown

objects can cause serious personal injury.

7. Plan your mowing pattern to avoid discharge of

material toward roads, sidewalks, bystanders and

the like. Also, avoid discharging material against a

wall or obstruction which may cause discharged

material to ricochet back toward the operator.

8. Always wear safety glasses or safety goggles

during operation and while performing an

adjustment or repair to protect your eyes. Thrown

objects which ricochet can cause serious injury to

the eyes.

9. Wear sturdy, rough-soled work shoes and close-

fitting slacks and shirts. Loose fitting clothes and

jewelry can be caught in movable parts. Never

operate this machine in bare feet or sandals.

10. Be aware of the mower and attachment discharge

direction and do not point it at anyone. Do not

operate the mower without the discharge cover or

entire grass catcher in its proper place.

11. Do not put hands or feet near rotating parts or

under the cutting deck. Contact with the blade(s)

can amputate hands and feet.

12. A missing or damaged discharge cover can cause

blade contact or thrown object injuries.

13. Stop the blade(s) when crossing gravel drives,

walks, or roads and while not cutting grass.

14. Watch for traffic when operating near or crossing

roadways. This machine is not intended for use on

any public roadway.

15. Do not operate the machine while under the

influence of alcohol or drugs.

16. Mow only in daylight or good artificial light.

17. Never carry passengers.

18. Disengage blade(s) before shifting into reverse.

Back up slowly. Always look down and behind

before and while backing to avoid a back-over

accident.

19. Slow down before turning. Operate the machine

smoothly. Avoid erratic operation and excessive

speed.

20. Disengage blade(s), set parking brake, stop engine

and wait until the blade(s) come to a complete stop

before removing grass catcher, emptying grass,

unclogging chute, removing any grass or debris, or

making any adjustments.

21. Never leave a running machine unattended.

Always turn off blade(s), place transmission in

neutral, set parking brake, stop engine and remove

key before dismounting.

22. Use extra care when loading or unloading the

machine into a trailer or truck. This unit should not

be driven up or down ramp(s), because the unit

could tip over, causing serious personal injury. The

unit must be pushed manually on ramp(s) to load or

unload properly.

23. Muffler and engine become hot and can cause a

burn. Do not touch.

24. Check overhead clearances carefully before driving

under low hanging tree branches, wires, door

openings etc., where the operator may be struck or

pulled from the unit, which could result in serious

injury.

25. Disengage all attachment clutches, depress the

brake pedal completely and shift into neutral before

attempting to start engine.

26. Your machine is designed to cut normal residential

grass of a height no more than 10”. Do not attempt

to mow through unusually tall, dry grass (e.g.,

pasture) or piles of dry leaves. Dry grass or leaves

may contact the engine exhaust and/or build up on

the mower deck presenting a potential fire hazard.

27. Use only accessories and attachments approved

for this machine by the machine manufacturer.

Read, understand and follow all instructions

provided with the approved accessory or

attachment.

28. Data indicates that operators, age 60 years and

above, are involved in a large percentage of riding

mower-related injuries. These operators should

evaluate their ability to operate the riding mower

safely enough to protect themselves and others

from serious injury.

29. If situations occur which are not covered in this

manual, use care and good judgment. Contact an

authorized Service Dealer for assistance.

SLOPE OPERATION

Slopes are a major factor related to loss of control and

tip-over accidents which can result in severe injury or

death. All slopes require extra caution. If you cannot

back up the slope or if you feel uneasy on it, do not mow

it.

For your safety, use the slope gauge included as part of

this manual to measure slopes before operating this

unit on a sloped or hilly area. If the slope is greater than

15 degrees as shown on the slope gauge, do not

operate this unit on that area or serious injury could

result.

DO:

1. Mow up and down slopes, not across. Exercise

extreme caution when changing direction on

slopes.

2. Watch for holes, ruts, bumps, rocks, or other

hidden objects. Uneven terrain could overturn the

machine. Tall grass can hide obstacles.

3. Use slow speed. Choose a low enough speed

setting so that you will not have to stop or shift while

on the slope. Tires may lose traction on slopes

even though the brakes are functioning properly.

Always keep machine in gear when going down

slopes to take advantage of engine braking action.

4. Follow the manufacturer’s recommendations for

wheel weights or counterweights to improve

stability.

5. Use extra care with grass catchers or other

attachments. These can change the stability of the

machine.

6. Keep all movement on the slopes slow and gradual.

Do not make sudden changes in speed or direction.

Rapid engagement or braking could cause the front

of the machine to lift and rapidly flip over backwards

which could cause serious injury.

7. Avoid starting or stopping on a slope. If tires lose

traction, disengage the blade(s) and proceed

slowly straight down the slope.

DO NOT:

1. Do not turn on slopes unless necessary; then, turn

slowly and gradually downhill, if possible.

2. Do not mow near drop-offs, ditches or

embankments. The mower could suddenly turn

over if a wheel is over the edge of a cliff, ditch, or if

an edge caves in.

3. Do not try to stabilize the machine by putting your

foot on the ground.

4. Do not use a grass catcher on steep slopes.

5. Do not mow on wet grass. Reduced traction could

cause sliding.

6. Do not shift to neutral and coast downhill. Over-

speeding may cause the operator to lose control of

the machine resulting in serious injury or death.

7. Do not tow heavy pull behind attachments (e.g.

loaded dump cart, lawn roller, etc.) on slopes

greater than 5 degrees. When going down hill, the

extra weight tends to push the tractor and may

cause you to loose control. (e.g. tractor may speed

up, braking and steering ability are reduced,

attachment may jack-knife and cause tractor to

overturn).

CHILDREN

1. Tragic accidents can occur if the operator is not

alert to the presence of children. Children are often

attracted to the machine and the mowing activity.

They do not understand the dangers. Never

assume that children will remain where you last

saw them.

a. Keep children out of the mowing area and in

watchful care of a responsible adult other

than the operator.

b. Be alert and turn machine off if a child enters

the area.

c. Before and while backing, look behind and

down for small children.

d. Never carry children, even with the blade(s)

shut off. They may fall off and be seriously

injured or interfere with safe machine

operation.

e. Use extreme care when approaching blind

corners, doorways, shrubs, trees or other

objects that may block your vision of a child

who may run into the machine.

f. To avoid back-over accidents, always

disengage the cutting blade(s) before

shifting into reverse. The “Reverse

Caution Mode” should not be used when

children or others are around.

g. Keep children away from hot or running

engines. They can suffer burns from a hot

muffler.

h. Remove key when machine is unattended to

prevent unauthorized operation.

i. Never allow children under 14 years old to

operate the machine. Children 14 years old

and over should read and understand the

operation instructions and safety rules in this

manual and should be trained and

supervised by a parent.

TOWING

1. Tow only with a machine that has a hitch designed

for towing. Do not attach towed equipment except

at the hitch point.

2. Follow the manufacturers recommendation for

weight limits for towed equipment and towing on

slopes.

3. Never allow children or others in or on towed

equipment.

4. On slopes, the weight of the towed equipment may

cause loss of traction and loss of control.

5. Travel slowly and allow extra distance to stop.

6. Do not shift to neutral and coast downhill.

SERVICE

SAFE HANDLING OF GASOLINE:

1. To avoid personal injury or property damage

use extreme care in handling gasoline. Gasoline is

extremely flammable and the vapors are explosive.

Serious personal injury can occur when gasoline is

spilled on yourself or your clothes which can ignite.

Wash your skin and change clothes immediately.

a. Use only an approved gasoline container.

b. Never fill containers inside a vehicle or on a

truck or trailer bed with a plastic liner. Always

place containers on the ground away from

your vehicle before filling.

c. When practical, remove gas-powered

equipment from the truck or trailer and refuel

it on the ground. If this is not possible, then

refuel such equipment on a trailer with a

portable container, rather than from a

gasoline dispenser nozzle.

d. Keep the nozzle in contact with the rim of the

fuel tank or container opening at all times

until fueling is complete. Do not use a nozzle

lock-open device.

e. Extinguish all cigarettes, cigars, pipes and

other sources of ignition.

f. Never fuel machine indoors.

g. Never remove gas cap or add fuel while the

engine is hot or running. Allow engine to cool

at least two minutes before refueling.

h. Never over fill fuel tank. Fill tank to no more

than ½ inch below bottom of filler neck to

allow space for fuel expansion.

i. Replace gasoline cap and tighten securely.

j. If gasoline is spilled, wipe it off the engine

and equipment. Move unit to another area.

Wait 5 minutes before starting the engine.

k. To reduce fire hazards, keep machine free of

grass, leaves, or other debris build-up. Clean

up oil or fuel spillage and remove any fuel

soaked debris.

l. Never store the machine or fuel container

inside where there is an open flame, spark or

pilot light as on a water heater, space heater,

furnace, clothes dryer or other gas

appliances.

m. Allow a machine to cool at least 5 minutes

before storing.

GENERAL SERVICE:

1. Never run an engine indoors or in a poorly

ventilated area. Engine exhaust contains carbon

monoxide, an odorless, and deadly gas.

2. Before cleaning, repairing, or inspecting, make

certain the blade(s) and all moving parts have

stopped. Disconnect the spark plug wire and

ground against the engine to prevent unintended

starting.

3. Periodically check to make sure the blades come to

complete stop within approximately (5) five

seconds after operating the blade disengagement

control. If the blades do not stop within the this time

frame, your unit should be serviced professionally

by an authorized Service Dealer.

4. Check brake operation frequently as it is subjected

to wear during normal operation. Adjust and service

as required.

5. Check the blade(s) and engine mounting bolts at

frequent intervals for proper tightness. Also,

visually inspect blade(s) for damage (e.g.,

excessive wear, bent, cracked).

Replace the blade(s) with the original equipment

manufacturer’s (O.E.M.) blade(s) only, listed in this

manual. “Use of parts which do not meet the

original equipment specifications may lead to

improper performance and compromise safety!”

6. Mower blades are sharp. Wrap the blade or wear

gloves, and use extra caution when servicing them.

7. Keep all nuts, bolts, and screws tight to be sure the

equipment is in safe working condition.

8. Never tamper with the safety interlock system or

other safety devices. Check their proper operation

regularly.

9. After striking a foreign object, stop the engine,

disconnect the spark plug wire(s) and ground

against the engine. Thoroughly inspect the

machine for any damage. Repair the damage

before starting and operating.

10. Never attempt to make adjustments or repairs to

the machine while the engine is running.

11. Grass catcher components and the discharge

cover are subject to wear and damage which could

expose moving parts or allow objects to be thrown.

For safety protection, frequently check components

and replace immediately with original equipment

manufacturer’s (O.E.M.) parts only, listed in this

manual. “Use of parts which do not meet the

original equipment specifications may lead to

improper performance and compromise safety!”

12. Do not change the engine governor settings or

over-speed the engine. The governor controls the

maximum safe operating speed of the engine.

13. Maintain or replace safety and instruction labels, as

necessary.

14. Observe proper disposal laws and regulations for

gas, oil, etc. to protect the environment.

WARNING: YOUR RESPONSIBILITY Restrict the use of this power machine to persons who read,

understand and follow the warnings and instructions in this manual and on the machine.

Safety labels found on your unit.

S30011

MAX 20

S30544

SECTION 2: SLOPE GAUGE

Use this page as a guide to determine slopes where you may not operate safely. Do not operate your lawn tractor

on such slopes.

15°

SIGHT AND HOLD THIS LEVEL WITH A VERTICAL TREE

A POWER POLE

A CORNER OF A BUILDING

OR A FENCE POST

DANGER

Do not mow on inclines with a slope in excess of 15 degrees (a rise of approximately 2-1/2 feet every 10 feet). A riding mower could

overturn and cause serious injury. If operating a walk-behind mower on such a slope, it is extremely difficult to maintain your footing

and you could slip, resulting in serious injury.

Operate RIDING mowers up and down slopes, never across the face of slopes.

Operate WALK-BEHIND mowers across the face of slopes, never up and down slopes.

SECTION 3: TRACTOR SET-UP

NOTE: This owner’s manual covers various models of

lawn tractors. The units illustrated may vary slightly

from your unit. Follow only those instructions which

pertain to your model lawn tractor.

Attaching the Battery Cables

NOTE: The positive battery terminal is marked Pos.

(+). The negative battery terminal is marked Neg. (–).

• The positive cable (heavy red wire) is secured to

the positive battery terminal (+) with a hex bolt and

hex nut at the factory. Make certain that the rubber

boot covers the terminal to help protect it from

corrosion.

• Remove the hex bolt and wing nut from the

negative cable.

• Remove the black plastic cover, if present, from the

negative battery terminal and attach the negative

cable (heavy black wire) to the negative battery

terminal (–) with the bolt and wing nut.

• Make certain the retainer rod is in position over the

battery, securing it in place. See Figure 1.

Figure 1

NOTE: If the battery is put into service after the date

shown on top of battery, charge the battery as

instructed in the SERVICE section of this manual prior

to operating the tractor.

Gas and Oil Fill-up

The gasoline tank is located under the hood and has a

capacity of either two or three gallons. Do not overfill.

WARNING: Use extreme care when

handling gasoline. Gasoline is extremely

flammable and the vapors are explosive.

Never fuel machine indoors or while the

engine is hot or running. Extinguish

cigarettes, cigars, pipes, and other sources of

ignition.

Service the engine with gasoline and oil as instructed in

the separate engine manual packed with your tractor.

Read instructions carefully.

IMPORTANT: Your tractor is shipped with motor oil in the

engine. However, you MUST check the oil level before

operating. Be careful not to overfill.

Shipping Brace Removal

WARNING: Make sure the riding mower’s

engine is off, remove the ignition key, and set

the parking brake before removing the

shipping brace

• Locate the shipping brace, if present, and

accompanying warning tag found on the right side

of the mower, between the discharge chute and the

cutting deck. See Figure 2.

Figure 2

• While holding the discharge chute with your left

hand, remove the shipping brace with your right

hand by grasping it between your thumb and index

finger and rotating it clockwise.

WARNING: The shipping brace, used for

packaging purposes only, must be removed

and discarded before operating your riding

mower.

Rubber Boot

Hex Bolt

Wing Nut

Retainer Rod

Shipping Brace

Warning Tag

WARNING: The mowing deck is capable of

throwing objects. Failure to operate the riding

mower without the discharge cover in the

proper operating position could result in

serious personal injury and/or property

damage.

Attaching the Steering Wheel

WARNING: Do NOT operate the tractor

without first attaching both the steering

wheel AND the seat. Doing so could result

in serious injury to the operator.

NOTE: There are two different styles of steering

wheel cap. See Figure 3. Styles vary by model.

• Using your hands, place the tractor’s front tires in

position for straight-ahead travel.

• Remove the steering wheel cap from the center of

the steering wheel. Be careful not to lose the hex

screw and cupped washer found beneath it.

• Place the steering wheel (in position for straight-

ahead travel) directly onto the steering shaft found

in the center of the tractor’s dash.

• Place the cupped washer (cupped side DOWN)

over the steering shaft.

• Thread the hex screw into the steering shaft and

tighten securely.

• Reinsert the steering wheel cap in the center of the

steering wheel. Refer to Figure 3

Figure 3

Attaching the Seat

Refer to Figures 4 and 5 to identify your tractor’s seat

style and follow applicable instructions.

NOTE: For shipping reasons, seats are either

fastened to the tractor seat’s pivot bracket with a plastic

tie, or mounted backward to the pivot bracket. In either

case, free the seat from its shipping position and

remove the two hex screws (or knobs, on models so

equipped) from the bottom of seat before proceeding

with applicable instructions below

Quick Adjustment Seat

NOTE: If your seat was shipped mounted backwards

on the seat pivot bracket, pull out the tab found on the

seat stop and hold it open while sliding the seat off the

seat pivot bracket. See Figure 4.

• Line up the plastic seat spacers with the slots in

seat pivot bracket.

• Slide seat in until front seat spacer engages the

seat stop. See Figure 4.

Figure 4

WARNING: Before operating this machine,

make sure the seat is engaged in the seat

stop, stand behind the machine and pull back

on seat until fully engaged into stop

Knob Adjustment Seat

• Position the shoulder screws (found on the base of

the seat) inside the slot openings in the seat pivot

bracket. See Figure 5.

• Slide the seat slightly rearward in the seat pivot

bracket, lining up the rear slots in the pivot bracket

with the remaining two holes in the seat’s base.

• Select desired position for the seat, and secure with

the two knobs removed earlier. See Figure 5.

Steering

Hex Bolt

Steering

Shaft

& Washer

Wheel Cap

Seat Stop

Tab

Pivot Bracket

QUICK ADJUSTMENT

Figure 5

SECTION 4: KNOW YOUR LAWN TRACTOR

Throttle Control Lever

The throttle control lever is located on the right side of

the tractor’s dash panel. This lever controls the speed

of the engine and, on some models, when pushed all

the way forward, the choke control also. When set in a

given position, the throttle will maintain a uniform

engine speed. See Figure 6.

Figure 6

IMPORTANT: When operating the tractor with the cutting

deck engaged, be certain that the throttle lever is

always in the FAST (rabbit) position.

Choke Control

On some models, moving the

throttle lever all the way forward

activates the engine’s choke

control. On all other models, the

choke control can be found on

the left side of the dash panel and

is activated by pulling the knob

outward. Activating the choke

control closes the choke plate on

the carburetor and aids in starting

the engine. Refer to Starting The Engine in the

OPERATION section of this manual for detailed starting

instructions.

Brake Pedal

The brake pedal is located on the

right front side of the tractor

above the drive pedal along the

running board. The brake pedal

can be used for sudden stops or

setting the parking brake.

NOTE: The brake pedal must be fully depressed to

activate the safety interlock switch when starting the

tractor

KNOB ADJUSTMENT

Knobs

Shoulder

Opening

Pivot Bracket

in Slot

Screws

Slow

Choke

Fast

Position

Slow

Fast

Position

AVOID SERIOUS INJURY OR DEATH

• GO UP AND DOWN SLOPES, NOT ACROSS.

• AVOID SUDDEN TURNS.

• DO NOT OPERATE THE UNIT WHERE IT COULD SLIP OR TIP.

• IF MACHINE STOPS GOING UPHILL, STOP BLADE(S) AND BACK

DOWNHILL SLOWLY.

• DO NOT MOW WHEN CHILDREN OR OTHERS ARE AROUND.

• NEVER CARRY CHILDREN, EVEN WITH BLADES OFF.

• LOOK DOWN AND BEHIND BEFORE AND WHILE BACKING.

• KEEP SAFETY DEVICES (GUARDS, SHIELDS, AND SWITCHES) IN

PLACE AND WORKING.

• REMOVE OBJECTS THAT COULD BE THROWN BY THE BLADE(S).

• KNOW LOCATION AND FUNCTION OF ALL CONTROLS.

• BE SURE BLADE(S) AND ENGINE ARE STOPPED BEFORE PLAC-

ING HANDS OR FEET NEAR BLADE(S).

• BEFORE LEAVING OPERATOR’S POSITION, DISENGAGE

BLADE(S), PLACE THE SHIFT LEVER IN NEUTRAL, ENGAGE

BRAKE LOCK, SHUT ENGINE OFF AND REMOVE KEY.

READ OPERATOR’S MANUAL

WARNING

Figure 7

NOTE: Any reference in this manual to the RIGHT or LEFT side of the tractor is observed from operator’s position.

NOTE: Hood styles vary by model.

A Systems Indicator Monitor/Hour Meter G Throttle Control

B PTO (Blade Engage) Knob H Ignition Switch Module

Choke Control

I Brake Pedal

D Parking Brake Button J Drive Pedal

E Shift Lever K Cruise Control Lever

F Cup Holder L Deck Lift Lever

Ignition Switch Module

WARNING: Never leave a running machine

unattended. Always disengage PTO, move

shift lever into neutral position, set parking

brake, stop engine and remove key to prevent

unintended starting.

To start the engine, insert the key into the ignition

switch and turn clockwise to the START position.

Release the key into the NORMAL MOWING MODE

position once the engine has fired.

To stop the engine, turn the ignition key

counterclockwise to the STOP position. See Figure 8.

Figure 8

IMPORTANT: Prior to operating the tractor, refer to both

Safety Interlock Switches, page 14 and Starting The Engine, page

15 of this manual for detailed instructions regarding the

Ignition Switch Module and operating the tractor in

REVERSE CAUTION MODE.

Drive Pedal

The drive pedal is located below

the brake pedal on the right front

side of the tractor along the

running board. Depress the drive

pedal with your right foot when

the tractor shift lever is in either

FORWARD or REVERSE to

cause the tractor to move.

Ground speed is also controlled

with the drive pedal. The further

down the pedal is depressed, the faster the tractor will

travel. The pedal will return to its original position when

it’s not depressed.

IMPORTANT: Always set the parking brake when

leaving the tractor unattended.

Systems Indicator Monitor

LCD

Located in the center of the tractor’s console, the

systems indicator monitor records, and displays on its

LCD, hours of tractor operation whenever the ignition

key is rotated out of the STOP position.

The indicator Monitor will also remind the oeprator of

maintenacne intervals for chaning the engine oil. The

LCD will alternately flash the recorded hours, “CHG”

and “OIL” for five minutes, after every 50 hours of

recorded operation elapse. The maintenance interval

lasts for two hours (from 50-52, 100-102, 150-152,

etc.). The LCD will also flash as described above for

five minutes every time the tractor’s engine has been

started during this maintenance interval. Befor the

interval expires, change the crankcase oil level as

instructed in this Operator’s Manual.

Figure 9

If the Brake light or PTO light illuminates when

attempting to start the unit, proceed as follows:

BRAKE — Depress the brake pedal.

PTO — Move PTO (Blade Engage) lever,

or PTO (Blade Engage) knob into the

disengaged (OFF) position.

NOTE: It is normal for the Oil light and the Battery light

to illuminate while the engine is cranking, but if either

illuminate’s while the engine is running, proceed as

follows:

OIL— Stop the tractor immediately and check

the crankcase oil level as instructed in

the Engine Operator/Owner

Manual included with your tractor.

BATTERY— The battery is in need of a charge, or the

engine’s charging system is not

generating sufficient amperage. Refer to

the MAINTENANCE section of this manual

Start

Position

Normal

Driving

Mode

Stop

Position

{Ó°äÊ

for the proper battery charging procedure

or have the charging system checked by

an authorized dealer.

On units so equipped, the ammeter (if so equipped)

measures the electrical output of the engine’s charging

system. Under normal operating conditions, with the

engine at full throttle, the ammeter’s needle should

measure a positive charge.

The hour meter (if so equipped) operates whenever

the engine is running and records the actual hours of

tractor operation.

Electric PTO

(Blade Engage) Knob

To engage the power to the

cutting deck or other (separately

available) attachments on

models equipped with an electric

PTO, pull outward on the PTO

(Blade Engage) knob. Push the

PTO (Blade Engage) knob

inward to disengage the power to the cutting deck.

NOTE: The PTO (Blade Engage) knob must be in the

disengaged (OFF) position when starting the engine,

when traveling in reverse and if the operator leaves the

seat.

Manual PTO (Blade Engage) Lever

On models equipped with a manual PTO (Blade

Engage), the PTO (Blade Engage) lever is located on

the left side of the dashboard next to the steering

wheel. Move the PTO (Blade Engage) lever forward to

engage the power to the cutting deck or other

(separately available) attachments; move the PTO

(Blade Engage) lever rearward to disengage the power

to the attachments.

NOTE: The PTO (Blade Engage) lever must be in the

disengaged (OFF) position when starting the engine,

when traveling in reverse and if the operator leaves the

seat.

Seat Adjustment Lever

To adjust the seat forward or backward on units

equipped with a quick-adjust seat, slide the seat

adjustment lever to the left and reposition the seat to

the desired position. Once a comfortable position is

found, release the seat adjustment lever to lock the

seat in place. Refer to Seat Adjustment of this manual for

more detailed instructions.

Deck Lift Lever

Found on your tractor’s right fender, the deck lift lever is

used to change the height of the cutting deck. To use,

move the lever to the left, then place in the notch best

suited for your application.

Parking Brake Button

To set the parking brake, fully

depress the brake pedal and

push the parking brake button in.

Hold the button in while taking

your foot off the brake pedal.

Both the parking button and the

brake pedal will then stay

depressed. To release the

parking brake, depress the brake

pedal slightly. The parking brake

button will then return to its original position.

NOTE: The parking brake must be set if the operator

leaves the seat with the engine running or the engine

will automatically shut off.

IMPORTANT: Always set the parking brake when

leaving the tractor unattended.

Cruise Control Button

The cruise control button is

located on the tractor dash panel

to the left of the ignition switch.

Push the cruise control button

while traveling forward at a

desired speed. While holding the

button in, release pressure from

the drive pedal. This will engage

the cruise control and allow the

tractor to remain at that speed

without applying pressure to the drive pedal. Depress

the brake pedal or the drive pedal to deactivate cruise

control. Refer to OPERATION SECTION this manual for

detailed instructions regarding the cruise control

feature.

NOTE: Cruise control can NOT be engaged at the

tractor’s fastest ground speed. If the operator should

attempt to do so, the tractor will automatically

decelerate to the fastest optimal mowing ground speed.

Cargo Net (optional)

Conveniently located on the tractor’s dash panel, the

cargo net can be used to store personal items while

operating the tractor.

MARCHE

PTO

PDF

OFF

ARRÊT

Shift Lever

The shift lever is located on the left side of the fender

and has three positions, FORWARD, NEUTRAL and

REVERSE. The brake pedal must be depressed and

the tractor must not be in motion when the moving shift

lever. See Figure 10.

IMPORTANT: Never force the shift lever. Doing so may

result in serious damage to the tractor’s transmission.

Figure 10

SECTION 5: OPERATING YOUR LAWN TRACTOR

Safety Interlock Switches

This tractor is equipped with a safety interlock system

for the protection of the operator. If the interlock system

should ever malfunction, do not operate the tractor.

Contact an authorized service dealer.

• The safety interlock system prevents the engine

from cranking or starting unless the parking brake is

engaged, and the PTO (Blade Engage) knob (or

lever) is in the disengaged (OFF) position.

• The engine will automatically shut off if the operator

leaves the seat before engaging the parking brake.

Models with Manual PTO (Blade Engage)

• The engine will automatically shut off if the operator

leaves the tractor’s seat with the PTO (Blade

Engage) lever in the engaged (ON) position,

regardless of whether the parking brake is

engaged.

• With the ignition key in the NORMAL MOWING

position, the engine will automatically shut off if the

PTO (Blade Engage) lever is moved into the

engaged (ON) position with the shift lever in

Reverse.

Models with Electric PTO (Blade Engage)

• The electric PTO (Blade Engage) clutch will

automatically shut off if the operator leaves the

tractor’s seat with the PTO (Blade Engage) knob in

the engaged (ON) position, regardless of whether

the parking brake is engaged.

• With the ignition key in the NORMAL MOWING

position, the electric PTO (Blade Engage) clutch

will automatically shut off if the PTO (Blade

Engage) knob is moved into the engaged (ON)

position with the shift lever in Reverse.

WARNING: Do not operate the tractor if the

interlock system is malfunctioning. This

system was designed for your safety and

protection.

Reverse Caution Mode

The REVERSE CAUTION MODE position of the key

switch module allows the tractor to be operated in

reverse with the blades (PTO) engaged.

IMPORTANT: Mowing in reverse is not recommended.

WARNING: Use extreme caution while

operating the tractor in the REVERSE

CAUTION MODE. Always look down and

behind before and while backing. Do not

operate the tractor when children or others

are around. Stop the tractor immediately if

someone enters the area.

To use the REVERSE CAUTION MODE:

IMPORTANT:The operator MUST be seated in the

tractor seat.

1. Start the engine as previously instructed in this

Operator’s Manual.

2. Turn the key from the NORMAL MOWING

(Green) position to the REVERSE CAUTION

MODE (Yellow) position of the key switch module.

See Figure 11.

3. Depress the REVERSE PUSH BUTTON (Orange,

Triangular Button) at the top, right corner of the key

switch module. The red indicator light at the top, left

corner of the key switch module will be ON while

activated. See Figure 11.

4. Once activated (indicator light ON), the tractor can

be driven in reverse with the cutting blades (PTO)

engaged.

5. Always look down and behind before and while

backing to make sure no children are around.

6. After resuming forward motion, return the key to the

NORMAL MOWING position.

IMPORTANT: The REVERSE CAUTION MODE will

remain activated until:

a. The key is placed in either the NORMAL

MOWING position or STOP position.

b. The operator leaves the seat (Models with

Electric PTO ONLY).

c. The operator engages the parking brake by

fully depressing the brake pedal and holding

it down while gently pushing the parking

brake button inward (Models with Manual

PTO ONLY).

Figure 11

Engaging the Parking Brake

To engage the parking brake:

• Fully depress the brake pedal and hold it down with

your foot while gently pushing the parking brake

button inward.

• Hold the parking brake button in while removing

your foot from the brake pedal.

• Once engaged, the parking brake button and the

brake pedal will lock in the “down” position.

To disengage the parking brake:

• Slightly depress the brake pedal.

NOTE: The parking brake must be engaged if the

operator leaves the seat with the engine running or the

engine will automatically shut off.

Setting the Cutting Height

Select the height position of the cutting deck by placing

the deck lift lever in any of the six different cutting height

notches on the right side of the fender. Then adjust the

deck wheels so that they are between ¼-inch and ½-

inch above the ground when the tractor is on a smooth,

flat surface such as a driveway.

WARNING: Keep hands and feet away

from the discharge opening of the cutting

deck.

NOTE: The deck wheels are an anti-scalp feature of

the deck and are not designed to support the weight of

the cutting deck.

Refer to Leveling the Deck, in the MAKING

ADJUSTMENTS section of this manual for more

detailed instructions regarding various deck

adjustments.

Starting the Engine

WARNING: Do not operate the tractor if the

interlock system is malfunctioning. This

system was designed for your safety and

protection.

NOTE: Refer to the TRACTOR SET-UP section of this

manual for Gasoline and Oil fill-up instructions.

• Insert the tractor key into the ignition switch.

• Place the PTO (Blade Engage) knob (or lever) in

the disengaged (OFF) position.

• Engage the tractor’s parking brake.

• Activate the choke control.

• Turn the ignition key clockwise to the START

position. After the engine starts, release the key. It

will return to the ON position.

IMPORTANT: Do NOT hold the key in the START

position for longer than ten seconds at a time. Doing so

may cause damage to your engine’s electric starter.

• After the engine starts, deactivate the choke control

and place the throttle control in the FAST position.

NOTE: Do NOT leave the choke control on while

operating the tractor. Doing so will result in a "rich" fuel

mixture and cause the engine to run poorly.

Stop

Position

Start

Position

Indicator

Light

Reverse

Push

Button

Reverse

Caution Mode

Position

Stopping the Engine

WARNING: If you strike a foreign object,

stop the engine, disconnect the spark plug

wire(s) and ground against the engine.

Thoroughly inspect the machine for any

damage. Repair the damage before restarting

and operating

• If the blades are engaged, place the PTO (Blade

Engage) knob (or lever) in the disengaged (OFF)

position.

• Turn the ignition key counterclockwise to the OFF

position.

• Remove the key from the ignition switch to prevent

unintended starting.

Driving the Tractor

WARNING: Avoid sudden starts, ex-

cessive speed and sudden stops.

WARNING: Do not leave the seat of the

tractor without first placing the PTO (Blade

Engage) knob (or lever) in the disengaged

(OFF) position, depressing the brake pedal

and engaging the parking brake. If leaving the

tractor unattended, also turn the ignition key

off and remove the key.

• Depress the brake pedal to release the parking

brake and let the pedal up.

• Move the throttle lever into the FAST (rabbit)

position.

IMPORTANT: Do NOT use the shift lever to change the

direction of travel when the tractor is in motion. Always

use the brake pedal to bring the tractor to a complete

stop before shifting.

• To move forward, place the shift lever in the

FORWARD position, then slowly depress the drive

pedal until the desired speed is achieved.

• To move in reverse, place the shift lever in the

REVERSE position, check that the area behind is

clear then slowly depress the drive pedal.

Driving On Slopes

Refer to the SLOPE GAUGE to help determine slopes

where you may operate the tractor safely.

WARNING: Do not mow on inclines with a

slope in excess of 15 degrees (a rise of

approximately 2-1/2 feet every 10 feet). The

tractor could overturn and cause serious

injury.

• Mow up and down slopes, NEVER across.

• Exercise extreme caution when changing direction

on slopes.

• Watch for holes, ruts, bumps, rocks, or other

hidden objects. Uneven terrain could overturn the

machine. Tall grass can hide obstacles.

• Avoid turns when driving on a slope. If a turn must

be made, turn down the slope. Turning up a slope

greatly increases the chance of a roll over.

• Avoid stopping when driving up a slope. If it is

necessary to stop while driving up a slope, start up

smoothly and carefully to reduce the possibility of

flipping the tractor over backward.

Setting the Cruise Control

• Place the shift lever in the FORWARD position,

then slowly depress the drive pedal until the desired

speed is achieved.

• Lightly depress the cruise control button.

• While continuing to hold the cruise button in, lift

your foot from the drive pedal (you should feel the

cruise latch engage).

• Once engaged, the cruise control button and the

drive pedal will lock in the “down” position, and the

tractor will maintain the same forward speed.

NOTE: Cruise control can not be engaged at the

tractor’s fastest ground speed. If the operator should

attempt to do so, the tractor will automatically

decelerate to the fastest optimal mowing ground speed.

Disengage the cruise control using one of the following

methods:

• Depress the brake pedal to disengage the cruise

control and stop the tractor.

• Lightly depress the drive pedal.

To change to the reverse direction when operating with

cruise control, depress the brake pedal to disengage

the cruise control and bring the tractor to a complete

stop. Then place the shift lever in the REVERSE

position and depress the drive pedal.

Engaging the Blades

Engaging the PTO (Blade Engage) transfers power to

the cutting deck or other (separately available)

attachments. To engage the blades, proceed as

follows:

• Move the throttle control lever to the FAST (rabbit)

position.

Models with Manual PTO

• Grasp the PTO (Blade Engage) lever and pivot it all

the way forward into the engaged (ON) position.

Models with Electric PTO

• Pull the PTO (Blade Engage) knob outward into the

engaged (ON) position. See Figure 12.

Figure 12

• Keep the throttle lever in the FAST (rabbit) position

for the most efficient use of the cutting deck or other

(separately available) attachments

IMPORTANT: The engine (on models with a manual

PTO) or electric PTO clutch (on models with an electric

PTO) will automatically shut off if the PTO is engaged

with the shift lever in position for reverse travel with the

ignition key in the NORMAL MOWING position. Refer

to Safety Interlock Switches.

Using the Deck Lift Lever

To raise the cutting deck, move the deck lift lever to the

left, then place it in the notch best suited for your

application. Refer to Setting The Cutting Height earlier in

this section.

Mowing

WARNING: To help avoid blade contact or

a thrown object injury, keep bystanders,

helpers, children and pets at least 75 feet

from the machine while it is in operation. Stop

machine if anyone enters the area.

The following information will be helpful when using the

cutting deck with your tractor.

WARNING: Plan your mowing pattern to

avoid discharge of materials toward roads,

sidewalks, bystanders and the like. Also,

avoid discharging material against a wall or

obstruction which may cause discharged

material to ricochet back toward the operator.

• Do not mow at high ground speed, especially if a

mulch kit or grass collector is installed.

• For best results it is recommended that the first two

laps be cut with the discharge thrown towards the

center. After the first two laps, reverse the direction

to throw the discharge to the outside for the

balance of cutting. This will give a better

appearance to the lawn.

• Do not cut the grass too short. Short grass invites

weed growth and yellows quickly in dry weather.

• Mowing should always be done with the engine at

full throttle.

• Under heavier conditions it may be necessary to go

back over the cut area a second time to get a clean

cut.

• Do NOT attempt to mow heavy brush and weeds

and extremely tall grass. Your tractor is designed to

mow lawns, NOT clear brush.

• Keep the blades sharp and replace the blades

when worn. Refer to Cutting Blades of this manual for

proper blade sharpening instructions.

Headlights

On some models, the lamps are ON whenever the

tractor’s engine is running. On other models, the lamps

are ON whenever the ignition key is moved out of the

STOP position.

On all models, the lamps turn OFF when the ignition

key is moved to the STOP position.

OFF

Front View

Pull Out

Push In

SECTION 6: MAKING ADJUSTMENTS

WARNING: Never attempt to make any

adjustments while the engine is running,

except where specified in the operator’s

manual.

Leveling the Deck

NOTE: Check the tractor’s tire pressure before

performing any deck leveling adjustments. Refer to

Tires section for information regarding tire pressure.

Front To Rear

The front of the cutting deck is supported by a stabilizer

bar that can adjusted to level the deck from front to rear.

The front of the deck should be between 1/4-inch and

3/8-inch lower than the rear of the deck. Adjust if

necessary as follows:

• With the tractor parked on a firm, level surface,

place the deck lift lever in the top notch (highest

position) and rotate the blade nearest the discharge

chute so that it is parallel with the tractor.

• Measure the distance from the front of the blade tip

to the ground and the rear of the blade tip to the

ground.

• The first measurement taken should be between

1/4" and 3/8" less than the second measurement.

Determine the approximate distance necessary for

proper adjustment and proceed, if necessary, to the

next step.

• Loosen the jam nut(s),on the rear side of the deck

stabilizer bracket.

• Locate the lock nut(s) on the front side of the

stabilizer bracket. See Figure 13. Tighten the lock

nut(s) to raise the front of the deck; loosen the lock

nut(s) to lower the front of the deck.

Figure 13

• Retighten the jam nut(s) loosened earlier when

proper adjustment is achieved.

Side to Side

If the cutting deck appears to be mowing unevenly, a

side to side adjustment can be performed. Adjust if

necessary as follows:

• With the tractor parked on a firm, level surface,

place the deck lift lever in the top notch (highest

position) and rotate both blades so that they are

perpendicular with the tractor.

• Measure the distance from the outside of the left

blade tip to the ground and the distance from the

outside of the right blade tip to the ground. Both

measurements taken should be equal. If they’re

not, proceed to the next step.

• Loosen, but do NOT remove, the hex cap screw on

the left deck hanger bracket. See Figure 14.

Figure 14

• Balance the deck by using a wrench to turn the

adjustment gear (found immediately behind the hex

cap screw just loosened) clockwise/up or

counterclockwise/down.

• The deck is properly balanced when both blade tip

measurements taken earlier are equal.

• Retighten the hex cap screw on the left deck

hanger bracket when proper adjustment is

achieved.

Parking Brake Adjustment

WARNING: Never attempt to adjust the

brakes while the engine is running. Always

disengage PTO, move shift lever into neutral

position, stop engine and remove key to

prevent unintended starting.

,OOSEN

TOLOWERDECK

4IGHTEN

TORAISEDECK

NOTE: 46-inch Deck Support Shown

Adjustment Gear

Hex Bolt

If the tractor does not come to a complete stop when

the brake pedal is completely depressed, or if the

tractor’s rear wheels can roll with the parking brake

applied, the brake is in need of adjustment. The brake

disc can be found on the right side of the transmission

in the rear of the tractor. Adjust if necessary as follows:

• Looking at the transmission from the right side of

the tractor, locate the compression spring and

brake disc. See Figure 15.

Figure 15

• Loosen, but do NOT remove, the hex nut found on

the right side of the brake assembly. See Figure 15.

• Using a feeler gauge, set the gap between the

brake disc and the brake puck at .011".

• Re-tighten the hex nut loosened earlier.

Seat Adjustment

WARNING: Before operating this machine,

make sure the seat is engaged in the seat

stop, stand behind the machine and pull back

on seat until fully engaged into stop.

Quick-Adjust Seat (if so equipped)

To adjust the position of the seat, move the seat

adjustment lever to the left and slide the seat forward or

rearward. Make sure seat is locked into position before

operating the tractor.

Knob Adjustment Seat (if so equipped)

To adjust the position of the seat on models so

equipped, loosen the two knobs on the bottom of the

seat. Slide the seat forward or backward as desired.

Retighten the two knobs.

Steering Adjustment

If the tractor turns tighter in one direction than the other,

or if the ball joints are being replaced due to damage or

wear, the steering drag links may need to be adjusted.

Adjust the drag links so that equal lengths are threaded

into the ball joint on the left side and the ball joint on the

right side:

• Loosen the jam nut found on the drag link at the

rear of the ball joint. See Figure 16.

Figure 16

• Remove the hex lock-nut on the top of ball joint.

See Figure 16.

• Thread the ball joint toward the jam nut to shorten

the drag link. Thread the ball joint away from the

jam nut to lengthen the drag link.

• Replace lock-nut and retighten the jam nut after

proper adjustment is achieved.

NOTE: Threading the ball joints too far onto the drag

links will cause the front tires to "toe-in" too far. Proper

toe-in is between 1/16" and 5/16".

Front tire toe-in can be measured as follows:

• Place the steering wheel in position for straight

ahead travel.

• In front of the axle, measure the distance

horizontally from the inside of the left rim to the

inside of the right rim. Note the distance.

• Behind the axle, measure the distance horizontally

from the inside of the left rim to the inside of the

right rim. Note the distance.

• The measurement taken in front of the axle should

be between 1/16" and 5/16" less than the

measurement taken behind the axle. Adjust if

necessary.

Brake Disc

Hex Nut

Compression

Spring

Set Gap

at .011"

NOTE: View shown from beneath tractor.

Transmission

Drag Link

Ball Joint

Axle

Pivot Bar

Hex Lock-Nut

Jam Nut

SECTION 7: MAINTAINING YOUR LAWN TRACTOR

WARNING: Before performing any

maintenance or repairs, disengage PTO,

move shift lever into neutral position, set

parking brake, stop engine and remove key to

prevent unintended starting.

Engine

Refer to the separate engine manual for engine

maintenance instructions.

Check engine oil level before each use as instructed in

the separate engine manual packed with your unit.

Read and follow instructions carefully.

Changing Engine Oil

NOTE: Depending on the engine model found on your

tractor, it may be necessary to remove the tractor’s side

panel in order to replace the oil filter (if so equipped).

• Unscrew oil fill cap and remove dipstick from the oil

fill tube. See Figure 17.

Figure 17

• Pop open the protective cap on the end of the oil

drain valve to expose the drain port. See Figure 17.

• Push the oil drain hose (packed with this manual)

onto the oil drain port. Route the opposite end of

the hose into an appropriate oil collection container

with a capacity of no less than 64 oz.

• Push the oil drain valve in slightly, then rotate

counterclockwise and pull outward to begin

draining oil. See Figure 17.

• Service the oil filter (if so equipped) as instructed

in the separate Engine Manual packed with your

unit.

Perform the above steps in the opposite order after oil

has finished draining.

• Refill the engine with new motor oil.

IMPORTANT: Refer to the separate engine manual

packed with your unit for information regarding the

quantity and proper weight of motor oil.

Air Cleaner

Service the pre-cleaner, if so equipped, and cartridge/

air cleaner element as instructed in the separate engine

manual packed with your unit.

Spark Plug(s)

The spark plug(s) should be cleaned and the gap reset

once a season. Spark plug replacement is

recommended at the start of each mowing season.

Refer to the separate engine manual for correct plug

type and gap specifications.

Lubrication

WARNING: Before lubricating, repairing, or

inspecting, always disengage PTO, move

shift lever into neutral position, set parking

brake, stop engine and remove key to prevent

unintended starting.

Engine

Lubricate the engine with motor oil as instructed in the

separate engine manual packed with your unit.

Pivot Points & Linkage

Lubricate all the pivot points on the drive system,

parking brake and lift linkage at least once a season

with light oil.

Rear Wheels

The rear wheels should be removed from the axles

once a season. Lubricate the axles and the rims well

with an all-purpose grease before re-installing them.

Front Axles

Each end of the tractor’s front pivot bar may be

equipped with a grease fitting. Lubricate with a grease

gun after every 25 hours of tractor operation.

Cleaning the Engine and Deck

Any fuel or oil spilled on the machine should be wiped

off promptly. Do NOT allow debris to accumulate

around the cooling fins of the engine or on any other

part of the machine.

IMPORTANT: The use of a pressure washer or garden

hose to clean your tractor is NOT recommended. It may

cause damage to electrical components, spindles,

pulleys, bearings or the engine. The use of water will

result in a shortened life of the tractor and reduce its

serviceability.

Protective Cap

Oil Drain Hose

Drain Port

Oil Fill Cap

Oil Fill Tube

Oil Drain Valve

La page charge ...

Toro LX500 Lawn Tractor Manuel utilisateur

Marque: Toro

Modèle: LX500 Lawn Tractor

Catégorie: Tondeuses à gazon

Taper: Manuel utilisateur

Télécharger le PDF

rapport

dans d''autres langues

English: Toro LX500 Lawn Tractor User manual

Toro LX500 Lawn Tractor Manuel utilisateur

Toro LX500 Lawn Tractor Manuel utilisateur

dans d''autres langues

Documents connexes

Autres documents