Jenn-Air JDB1080AWB36 Le manuel du propriétaire

Catégorie
Lave-vaisselle
Taper
Le manuel du propriétaire
JENN-AIR DISHWASHER
JDB-5
USE & CARE
GUIDE
I_]ENN-AIR
6 920374 B
TABLE OF CONTENTS
Safety .......................................................................................1
Operating Tips ....................................................................2-3
Loading ..................................................................................3-8
2-Rack Loading .........................................................3-5, 8
3-Rack Loading ..............................................................6-8
Dishwasher Use ....................................................................9
Cycles, Options and Lights ......................................10-14
What Can & Cannot Be Washed ..................................14
Care & Cleaning .................................................................15
Troubleshooting ...........................................................16-18
Warranty and Service .......................................................19
Guide d'utilisation et d'entretien ..................................20
Guia de Uso y Cuidado ...................................................40
SAFETY
What You Need to Know About
Safety instructions
Warning and Important Safety Instructions appearing in this
guide are not meant to cover all possible conditions and
situations that may occur. Common sense, caution and care
must be exercised when installing, maintaining or operating
the dishwasher.
Always contact your manufacturer about problems or
conditions you do not understand.
Recognize Safety Symbols, Words, Labels
important Safety instructions
Products with a _ label have been listed with
Underwriter's Laboratories, Inc. - those with a CSA tag have
been listed with Canadian Standards Association.
Nevertheless, as with any other equipment using electricity
and moving parts, there is a potential hazard.
1. Readall instructions before using the dishwasher.
2. Use the dishwasher only for its intended function.
3. Disconnect electrical power to dishwasher before
attempting to service.
4. To avoid electrical shock hazard, the sides and back
must be enclosed and the front panels must be
attached before electrical power is applied to the
dishwasher. Refer to the installation instructions for
proper grounding procedures.
5. Connect to a properly rated, protected and sized
power supply circuit to avoid electrical overload.
6. Children should never be permitted to operate, or
play in, with, or around this dishwasher.
7 Toreduce the risk of injury when loading items to be
washed, sharp or pointed items should be located with
the handles up. Also, load sharp items so they are not
likely to damage the door seal.
8. Do not touch the heating element on the bottom of
the tub during or at the completion of a cycle. It will
be hot.
9. Use only detergents and rinse additives designed for a
residential automatic dishwasher. Never use soap,
laundry detergent, or hand washing detergent in your
dishwasher. Keep these products out of reach of
children.
10. Do not sit, stand on or abuse the door or dish racks
of the dishwasher.
11. Under certain conditions, hydrogen gas may be
produced in a hot water system that has not been
used for two weeks or more. Hydrogen gas is
expletive. If the hot water system has not been used
for such a period, turn on all hot water faucets and let
the water flow from each for several minutes. This will
release any accumulated hydrogen gas. As the gas is
flammable, do not smoke or use an open flame during
this process.
12. Do not wash plastic items unless marked "dishwasher
safe" or the equivalent. For plastic items not so
marked, check the manufacturer's recommendations.
13. Be not tamper with controls.
14. To prevent accidental child entrapment and
suffocation risks, always remove the door to the
washing compartment when removing an old
dishwasher from service or discarding it.
15. Use caution when unloading the dishwasher. Dishes
will be hot if unloaded shortly after a cycle has
completed.
16. Certified residential dishwashers are not intended for
licensed food establishments.
1Z Toavoid water, mold or mildew damage to your home,
inlet and drain hose connections should be checked
periodically for leaks.
Save These Instructions
for Future Reference
OPE Ti
Before You Start
* Don't prerinse. Simply scrape off any hones or
large food particles.
,, if connected to a food waste disposer, make certain
the disposer is empty before starting the
dishwasher.
Scrape off tomato-based food soils (see page 15).
* Remove certain foods such as mustard,
mayonnaise, lemon juice, vinegar, salt or dressings
from stainless steel flatware as soon as
possible. These foods may cause rusting and pitting
if allowed to remain in contact with the surface for
an extended period of time.
Operating the Dishwasher
CModels with front or combination front and
top touchpad controls)
1. After loading the dishwasher and adding
detergent, select the desired cycle and options by
pressing the pads. The indicator lights for the
selected cycle and options will illuminate. To cancel
an option press the pad again.
2. To start a cycle, close the door until it latches then
press the START/Cancel pad once. After a pause,
the fill will begin. The display countdown (select
models) will flash until START/Cancel is pressed.
Note
* If START/Cancel is not pressed within 30
seconds of choosing your cycle, the dishwasher
will turn off.
* To prevent unplanned cycle or option changes,
these selections are "locked in" after 1 minute.
The dishwasher remembers your last cycle so you
do not have to reset the cycle each time. To start
the dishwasher using the same cycle and options
selected on the previous wash, just press the
START/Cancel pad.
3. To cancel a running cycle, press the START/
Cancel pad once. The dishwasher will drain, then
shut off. To turn the dishwasher off without
draining, press the START/Cancel pad twice.
Note
If a cycle pad is pressed after the controls have
been "locked in", the light above the current cycle
will flash three times.
Operating the Dishwasher
(Models with top only tonchpad controls)
1. After loading the dishwasher and adding
detergent, select the desired cycle and options by
pressing the pads. The indicator lights for the
selected cycle and options will illuminate. To cancel
an option press the pad again.
.
To start a cycle, press the START/Cancel pad
once. The indicator light will illuminate. Close the
door until it latches. After a pause, the fill will
begin.
Note
If START/Cancel is not pressed within 30
seconds of choosing your cycle, the dishwasher
will turn off.
To prevent unplanned cycle or option changes,
these selections are "locked in" after 1 minute.
.
The dishwasher remembers your last cycle so you
do not have to reset the cycle each time. To start
the dishwasher using the same cycle and options
selected on the previous wash, just press the
START/Cancel pad.
To cancel a running cycle, carefully unlatch the
door without opening completely and wait for
water circulation to stop. Press the START/
Cancel pad once and then shut the door. The
dishwasher will drain, then shut off. To turn the
dishwasher off without draining, press the
START/Cancel pad twice and then shut the door.
Note
If a cycle pad is pressed after the controls have
been "locked in", the light above the current cycle
will flash three times.
Cont.
2
T|
Operating the Dishwasher
(iVlodels with cycle selector knob)
1. After loading the dishwasher and adding
detergent, select the desired cycle by turning the
cycle selector knob. Select options by pressing the
buttons. The indicator lights for the options will
illuminate. To cancel an option, press that button
again.
2. To start a cycle, close the door until it latches then
press the START button once. After a pause, the
fill will begin.
Note
If START is not pressed within 30 seconds of
choosing your cycle, the dishwasher will turn off.
To prevent unplanned cycle or option changes,
these selections are "locked in" after one minute.
3. To cancel a running cycle, turn the cycle selector
knob to Brain/OFF. The dishwasher will drain,
then shut off. To turn the dishwasher off without
draining, turn the cycle selector knob to Brain/
OFF then press the START button once.
Adding a Forgotten item
For best cleaning, the forgotten item should be added
early in the cycle.
1. Grasp door handle and unlatch door without
opening completely. All lights will flash to indicate
that the cycle is suspended.
2. Wait for the water circulation to stop.
3. Open the door and add the item.
Close and latch the door. Lights will stop flashing
when the door is properly shut. After a slight
delay, the cycle resumes automatically at the point
of interruption.
Notes
If the door is opened during a running cycle,
there may be up to a 30 second delay before the
dishwasher restarts after closing the door.
Extended interruption of the wash cycle is not
recommended.
LOAD|
General Recommendations
CRack features vary by model[}
Items can be centered behind a single tine or loaded
at an angle to maximize space.
Avoid blocking or preventing the spray arms from
spinning freely. Do not allow items to extend beyond
the racks.
Face soiled surfaces toward the center of the
dishwasher.
For best dishwashing results follow guidelines on
following pages to determine the best arrangement for
your items.
-RACK LOADI (SELECTMODELS]
10 Place Setting Load
Upper Rack
3 saucers are
loadedonthe
rackunderthe
Stack=Rack
Shelf
(select
models)
Lower Rack
Upper Rack
Glasses, cups, stemware, light-weight plastics, plates,
bowls, pans, long-handled utensils etc. can be loaded
in this rack. Do not load glasses over the tines.
The Stack-Rack (select
models) on the right
side of the upper rack
folds up or down for
loading flexibility. Fold it
down to hold long-
handled knives, spatulas and spoons or short items
like cups or juice glasses. Fold it up for taller items like
glasses, bowls, plates, etc.
The edge of the Stack-
Rack (select models) is
designed to hold
stemware in place. Taller
stemware will fit better on
the right side as the
upper rack is deeper on
this side.
The Folding Tines (select
models) located in the
front right corner provide
convenient loading space
for large, bulky items like
pots and pans or mixing
bowls.
To lower tines, carefully push the tines out of each
holder toward the center of the rack and lay the tines
down.
The Cup Clips (select
models) located in the
center of the upper rack
can be used to hold light-
weight plastic items,
cooking utensils, knives,
etc. in place. Clip the item
between the tine and the clip.
The Vari-Lock TM Snugger
(select models) on the left
secures lightweight items
in place. It can be
adjusted by grasping the
wavy wire and rotating it
left to snug items against
the outer rack or to the
right to rest on top of light items. Do not load items
on top of the wire.
For best results with tall
glasses, rest the bottom of
the glass against the wavy
wire of the Vari-Lock TM
Snugger (select models).
Cont.
2-RACK LOADI G SELECT MODELS )
Lower Rack
A variety of items such as
dinner plates, mixing bowls,
pots and pans and baking
dishes can be loaded in this
rack.
Tall items such as bakeware
and large platters can be
placed on the left side.
With the Stack-
Rack (select
models} shelf
raised, thin items
like cookie sheets
or pizza pans
may be placed
along the left
side. With the shelf down, two levels of glasses and
cups can be loaded.
Positioning the Fold-
Away T"Tines (select
models} flat in the back,
left corner provides
convenient loading space
for large, bulky items like
pots and pans or mixing
bowls.
Convertible Tines (select
models} in the back, right
corner can be adjusted to
provide narrow spacing for
loading plates or wide spacing
for loading deep bowls, pots or
pans. Flip tines up for narrow
spacing or down for wider
spacing.
Back
Utensil Baskets
Removable Standard Utensil
Basket ([select models)
For best cleaning results, prevent
items from nesting together by
placing some items in the basket
with handles up and some with
handles down. Load knives,
handles up and spoons and forks
handles down, through the slots in
the hinged covered section(s} (when closed}.
Be sure that thin, finely pointed items do not extend
through the basket. This could block the lower wash
arm.
Small, lightweight items like baby spoons and plastic
measuring spoons should be placed in the section(s}
with the hinged cover(s}.
Split & Fit "_Utensil Basket
([select models)
The split silverware basket can
be separated and placed in
several locations in the bottom
rack. Load flatware and utensils
into both sections or just one,
depending on your load.
To split the
basket, hold
the basket
firmly along
the sides.
Unlock
baskets as
shown here.
½
Auxiliary Basket
([select models[}
Use this supplemental
basket in the upper rack
for loading miscellaneous
items and utensils. This is
also a safe place to load
sharp knives and pointed items.
5
3-RACK LOADI (SELECT MODELS)
10 Place Setting Load
1 Saucer
is loaded
behind
dinner
plates.
Upper Rack
Nliddle Rack
u u
Lower FiexLoodT_Rock
Upper Rack
Glasses, cups, stemware,
light-weight plastics,
plates, bowls, pans, long-
handled utensils etc. can
be loaded in this rack. Do
not Joad gJasses over
the tines.
The Stack-Rack (select
models) on the right side
of the upper rack folds
up or down for loading
flexibility. Fold it down to
hold long-handled
knives, spatulas and
spoons or short items
6
like cups or juice glasses. Fold it up for taller items like
glasses, bowls, plates, etc.
The edge of the Stack-
Rack (select models) is
designed to hold stemware
in place. Taller stemware
will fit better on the right
side as the upper rack is
deeper on this side.
The Folding Tines (select
models) located in the front
right corner provide
convenient loading space for
large, bulky items like pots
and pans or mixing bowls.
To lower tines, carefully
push the tines out of each
holder toward the center of
the rack and lay the tines
down.
The Cup Clips (select
models) located in the
center of the upper rack
can be used to hold light-
weight plastic items,
cooking utensils, knives,
etc. in place. Clip the item
between the tine and the
clip.
The Vari-Lock T"Snugger
(select models) on the left
secures lightweight items in
place. It can be adjusted by
grasping the wavy wire and
rotating it left to snug items
against the outer rack or to
the right to rest on top of
light items. Do not load
items on top of the wire.
For best results with tall
glasses, rest the bottom of
the glass against the wavy
wire of the Vari-Lock TM
Snugger (select models).
Cont.
3-RAC LOADI G (:SELECTMODELS)
Middle Rack
A variety of items such
as cups, glasses, dinner
plates, mixing bowls,
pots and pans and
baking dishes can be
loaded in this rack.
Positioning the Fold-
Away" Tines (select
models) flat in front or
back of the silverware
basket provides
convenient loading
space for large, bulky
items like casserole
dishes, water pitchers,
pots and pans or
mixing bowls.
Lower FlexLoad TM Rack
A variety of large items
such as casserole
dishes, baking pans,
mixing bowls, and pots
and pans can be
loaded in the lower
rack. When deeper
dishes or pots and pans
are located in this rack,
the middle rack can be
raised (see page 8). To accommodate exceptionally
large, occasionally used items such as a canner on the
lower FlexLoad" rack, the middle rack can be removed
(see page 8). For good wash action, place items so
soiled surfaces face down in the rack.
Utensil Baskets
When covers are not in use, place flatware in basket
some handles up and some down to avoid nesting.
Small, lightweight items like
baby spoons and plastic
measuring spoons should
be placed in a section of
the basket with cover
closed.
The split silverware basket
can be separated in the
event both sections are not
needed to hold silverware.
To split the basket, hold the
basket firmly along the sides.
Unlock baskets as shown
here.
Auxiliary Basket (select models)
Use this supplemental
basket in the upper or
middle rack for loading
miscellaneous items and
utensils. This is also a
safe place to load sharp
knives and pointed items.
Utility Basket for Lower Rack (select models)
This basket is
designed to load
miscellaneous items
like silverware,
cooking utensils,
knives and other
larger utensils.
Split & FiC Utensil Basket
For best cleaning results, prevent items from nesting
together by placing a utensil in each slot. Load knives,
handles up and spoons and forks
handles down through the slots.
Be sure that thin, finely pointed
items do not extend through the
basket bottom. This could block
the wash arm.
7
LOAD|
Adjnstable Racks [select models}
The Adjustable Upper Rack (select models) and
Adjustable Middle Rack can be raised or lowered to
accommodate taller plates, platters, pans, etc. in the
upper, middle or lower racks. Full size dinner plates
can be loaded in the upper rack if it is in the lower
position. Always unload racks before adjusting.
To lower the rack:
1. Pull the rack fully out.
2. Place thumbs
on each lever
on the adjuster
while holding
rack with
hands.
Adjusters
3. Press down on
the levers with
thumbs and push rack down. The rack will come
to a stop when it is in position.
To raise the rack:
1. Pull the rack fully out.
2. Place hands on both sides and lift up until rack
comes to a stop and latches in place.
Notes
The dishwasher will not _
operate correctly if the _
rack wash arm _
connection is not aligned _
with one of the water _ _
inlet holes on back wall _ _
of the dishwasher. _ .... _ _
* The left and right side adjusters on the racks
must both be fully in the upward or downward
position for proper connection.
Removing the Upper
and Middle Racks
The racks can be removed when tall or oversized items
need to be loaded into the middle or lower rack.
Unload the rack before removing it from the dishwasher.
To remove rack with push tab rack stops [select
models}:
1. Roll the rack '_ to '/2of the way out.
2. To remove each plastic push tab rack stop from
the end of each track, push inward (toward the
rack) on the ridged area of the rack stop. The rack
stop will snap open and can be easily removed by
pulling straight
out. Take care to
support the track
while removing
rack stops.
3. Roll the rack all
the way out of
the track and
remove from the
dishwasher.
To replace:
Push Tab
Rack Stop
Reverse the above procedure to replace the rack into
the dishwasher.
To remove rack with tab-lock rack stops
(select models[}
1. Roll the rack _ to '/_of the way out.
2. Locate the rack stops at the end of each track.
Squeeze the tab in the middle of the rack stop and
pull the rack stop straight out. Take care to support
the rack while removing the rack stops.
3. Roll the rack all the
way out of the
track and remove
from the
dishwasher.
To replace:
1. Replace the
dishwasher rack by
guiding the wheels into the tracks.
2. Push each rack stop squarely into the end of the
track until the catch pops into the small hole on the
side of the track.
SE
Hot Water
For optimal cleaning and drying results, hot water
is necessary. The incoming water temperature
should be 120 ° F C49° CD to properly activate the
detergent and melt greasy food soils.
To check the incoming water temperature, turn on the
hot water faucet nearest the dishwasher and let it run
into a glass in the sink. Place a candy thermometer in
the glass and check the temperature once it has
stopped rising.
Add recommended amount of detergent to each cup
as shown and close the detergent lid.
Detergent
Use a detergent designed specifically for use in an
automatic dishwasher. Be sure it is fresh. Store
granular detergent in a cool, dry place ([not under
the sink}.
Recommended Amount
Too little detergent results in poor cleaning, hard water
filming/spotting and poor drying. Too much detergent
can cause permanent etching/cloudiness.
The amount of detergent to use is determined by the
hardness of the water and soil level of the load. Refer
to the following chart for detergent usage
recommendations.
Light Soil 2 tsp 6 tsp
Soft 1:0=4 gpg} Normal Soil 4 tsp 6 tsp
Heavy Soil 4 tsp 7 tsp
Light Soil 4 tsp 6 tsp
Medium (5=9 gpg) Normal Soil 4 tsp 6 tsp
Heavy Soil 5 tsp 7 tsp
Hard (10=12 gpg) All Levels 5 tsp 8 tsp
*Your local water utility or state university extension service can tell
you the degree of water hardness in your area.
Jn extremely hard water conditions [13 grains per
gallon or more*), it is difficult to achieve good
results with any dishwasher. A mechanical water
softener may he necessary to improve water
quality, detergent effectiveness, and protect the
dishwasher parts from the damage that hard
water can Cause.
Do not use detergent with the Rinse Only cycle.
Leave the detergent lid open when running Rinse
Only.
Rinse Aid
Regular use of a rinse aid improves drying,
reduces spotting and filming, and reduces
moisture left on the dishwasher interior.
An automatic rinse aid dispenser is located next to the
detergent cup.
The window next to the dispenser cap indicates when
the rinse aid reservoir needs to be refilled. When the
level of rinse aid is below the indicator marks and the
window is nearly clear, it is time to refill the dispenser.
Check the dispenser monthly.
To add rinse aid to the
dispenser, turn the cap
counterclockwise to open.
Remove the cap and pour
liquid rinse aid into the
opening. The amount of
rinse aid dispensed during
the cycle is adjustable by
moving the lever inside the reservoir area. For most
water conditions use the manufacturer recommended
setting of "2". Adjust it up to the "MAX" setting for hard
water: Set the lever anywhere between these amounts as
needed to get the best results. Replace the cap and turn
it clockwise to close.
CYCLES LI
Cycles
Choose the cycle that best describes your dishload by pressing the corresponding touchpad. (See page 2,
Operating Tips, for how to begin the cycle).
Heavy Wash Long cycle for heavy food soils. 132 2 washes/3 rinses
Medium cycle for average food
Normal Wash soils. ClearScan T"Turbidity 97-117 1-2 washesV1-2 rinses_
sensor is active with this cycle.
China/Crystal Short cycle for light food soils. 82 1wash/2 rinses
Sensor Clean
(select models)
Designed to select the number
of water fills best suited for the
soil level of each load, ClearScan
Turbidity sensor is active with
this cycle,
94-128 1-2 washesV2-3 rinses_
Rinses dishes being held until 9 1 rinse
Rinse Only there is a full load.
Quick Wash or Quick cycle for light food soils. 38 1wash/2 rinses
Insta Wash Does not include drying time.
(select models)
Numberof fills will varydependingon the soil levelof eachload.
Notes
Depending on water temperature, there may be time added to the cycle to bring water up to temperature.
Cycle times shown in the numerical display (select models) will increase or decrease, based on each load's soil
level, water temperature and selected options.
Only the following certified cycles have been designed to meet NSF requirements (NSF/ANSI 184 Residential
Dishwasher) for sanitization: Sensor Clean (select models), Heavy Wash, Normal Wash and China/Crystal.
Cont.
10
CYCLES L|G
Cycle Options
In addition to choosing a cycle from page 10, choose as many available options as are needed for your load.
Super Scrub Selected when washing loads with hard-to-remove food soils. Heavy Wash*
(select models) Depending on which cycle is being used, this option adds Normal Wash*
heat and/or wash time to the wash cycle. China/Crystal
Sensor Clean* (select,_,o_el_
Steam Clean Selected to deep clean and shine by using vaporized water. Heavy Wash*
(select models) This option extends the wash cycle time to heat the water. Normal Wash*
China/Crystal
Sensor Clean* (select models)
Sanitize
(select models)
Sanitizes dishware. When cycle monitor recognizes that the
proper conditions have been met, the Sanitized light will
activate at the end of the cycle. Sanitization may not be
achieved if there is an interruption of the cycle, power failure
or if the incoming water temperature is below 120° F (49° C).
Heavy Wash*
Normal Wash*
Sensor Clean* (s_l_ctmo_Jels)
Hi Temp Wash Hi Temp Wash provides additional heat during the wash portion All cycles
(select models) of the cycle, which ensures proper water temperature for better (except Rinse Only
cleaning and drying results. It also adds an additional rinse to [select models])
the cycle which improves results in hard water situations.
Extra Rinse Adds an additional rinse to cycle. An extra rinse helps to All cycles
(select models) improve results in hard water situations. (except Rinse Only)
160 ° Rinse Raises temperature in the final rinse to 160° E This option can Heavy Wash*
(select models) be used with any cycle except Quick Wash (select models) Normal Wash*
and Rinse Only. Sensor Clean* (s_ctmo_*e_;
Heated Dry For enhanced drying results select this option. When Heated
Dry is not selected, towel drying of some items such as plastic
and items with non-stick surfaces may be necessary and more
moisture may be noticed adhering to the dishwasher interior.
In models with plastic interiors, it is normal to notice vapor
escaping from the door vent as the heat dries your dishes.
Vapor will escape even if Heated Dry is not selected.
Heavy Wash*
Normal Wash*
China/Crystal
Sensor Clean* (select models)
Only these cycles have been designated to meet NSF requirements [NSF/ANS1184 Residential Dishwasher) for sanitization.
Options
Start/Cancel Starts and stops dishwasher. See page 2 under Operating Tips: All Cycles
Operating the Dishwasher, for explanation.
Used to automatically start the cycle at a later time. See page 12 All Cycles
Delay for instructions.
Control Lock Option Locks control touchpad to prevent unwanted use. See page 13 All Cycles
(select models) for instructions.
11
CYCLES, OPT|O LIG
Lights/Display
Delay
The Delay option can be used to automatically start
the cycle at a later time to reduce daytime heat
buildup in the home or to take advantage of reduced
energy costs if available in your area. This option is
also useful for conserving hot water at times of high
household usage (showers, laundry).
To set up a Delay:
1. Select the appropriate cycle and options for the
load. Close the door.
2. Press the Delay pad or button until the desired
amount of delay time is selected.
3. The Delay indicator and the count down display
(select models) will flash until the START/Cancel
pad or START button is pressed.
4. As soon as the START/Cancel pad or START
button is pressed, the flashing will stop and the
delay time will begin counting down. The Delay
indicator will remain lit until the delay time has
counted down.
5. The cycle will automatically start as soon as the
delay time expires.
Note
If 30 seconds elapse between setting the cycle
and options and pressing the START/Cancel pad
or START button, the dishwasher will turn off.
To cancel a Delay:
When the delay is counting down, press the Delay
pad or button again. The indicator light will go out and
the cycle will start or resume immediately.
To cancel a Delay and the cycle:
JAil touchpad control models]
Press START/Cancel once to drain and turn off the
dishwasher.
Or
Press START/Cancel twice to turn dishwasher off
without draining.
To cancel a Delay and the cycle:
(Cycle selector knob models)
Turn the cycle knob to Drain/OFF. The dishwasher
will drain, then turn off.
Or
Turn the cycle knob to Drain/OFF, press the START
button once. The dishwasher will turn off without
draining.
Cont.
12
CYCLES, OPT| LIG
Control Lock
Option cse=ectmode=s)
The control touchpads can be locked to prevent
unwanted use. If this feature is activated between
cycles, the dishwasher cannot be operated until the
controls are unlocked. If desired, the controls can be
locked after a cycle or delay has started.
Setting the Control Lock:
1. Press the Heated Dry pad for three seconds.
2. An indicator light next to the lock graphic will
illuminate when the controls are locked.
To Cancel:
1. Press the Heated Dry pad for three seconds.
2. The indicator light will go off.
Notes
If a cycle or option pad is pressed afterthe
controls have been locked, the indicator light next
to the lock graphic will flash five times. On
selected models with a countdown display, the
display will flash an "L" simultaneously with the
lock indicator.
This option does not lock the door, only the
dishwasher controls.
13
CYC L|
Lights/Display cse=ectmode s)
TIME REMAiNiNG Display
(select models)
Shows approximate minutes remaining in a cycle. The symbol "2H" will appear when cycle time is greater
than 99 minutes. Cycle times shown in the numerical display (select models] will increase or decrease,
based on each load's soil level, water temperature and selected options.
CLEAN Light Illuminates at the end of the cycle and remains lit until the door has been open for 30 seconds
continuously.
DRYING Light Illuminates during the entire dry period and goes out when the cycle is completed.
(select models)
WASHING Light Illuminates during all rinse and wash portions of the cycle. On models with a cycle selector knob, the
(select models) Washing Light will remain illuminated during the entire cycle including dry.
HEATING DELAY Light
(select models) Illuminates when cycle is being extended to heat the water.
SANITIZED Light Illuminates at the end of the cycle when conditions have been met to achieve sanitization. The light will
(select models) remain lit until the door has been open for 30 seconds continuously.
Notes
When Sanitize is selected, cycles are monitored to assure sanitization. The SANITIZED light will not activate if
sanitization requirements are not met. This could happen if the cycle is interrupted,power failure occurs or incoming
water temperature is below 120° F [49° F].
The Clean and Sanitized indicatorlights [select models] will not relight after a power failure until after the next cycle isrun.
C C
Most tableware, cookware and flatware can safely be washed in your dishwasher. Check with the manufacturer.
Aluminum Yes, except anodized. High water temperature and detergents may affect finish.
Cast Iron No Seasoning will be removed, and iron will rust.
Yes, except antique or Always check manufacturer's recommendation before washing. Antique, hand-
China/Stoneware hand-painted, painted or over-the-glaze patterns may fade. Gold leaf may discolor.
Crystal Yes, except antique or Always check manufacturer's recommendation before washing. Some types of
delicate crystal, leaded crystal may etch with repeated washings.
Filters Not recommended. May leave a dingy deposit or stain on dishwasher interior.
Glass Yes A specialty glass called milk glass can yellow with repeated dishwasher washing.
Gold=Plated Flatware No Will discolor.
Pewter, Tin No
Yes, top rack, except Always check manufacturer's recommendation before washing. Plastics vary in
Plastics disposable plastic items, their capacity to withstand high water temperatures and detergents. Disposable
plastic items are not dishwasher safe for this reason.
Run a Rinse Only cycle if not washing immediately. Prolonged contact with
Stainless Steel Yes foods containing salt, vinegar, milk products or juice could damage finish.
Always check manufacturer's recommendation before washing. Run a Rinse
Sterling Silver or No, if has commercial Only cycle if not washing immediately. Prolonged contact with food containing
Silverplate "darkening". salt, acid or sulfide (eggs, mayonnaise and seafood] could damage finish.
Commercial "darkening" may be removed by detergent.
Wooden items No Wood may warp, crack or discolor.
14
CAR CLEAN|
General Recommendations
* The dishwasher interior is normally self-cleaning.
Periodically check the bottom of the dishwasher tub
to see if any large particles remain.
Wipe the edge of the inner door liner to remove any
food soil splashes which occurred during loading.
When cleaning the stainless steel exterior, always
wipe with the grain. Never use products containing
chlorine bleach or citric acid.
* The color from some tomato-based food soils may
occasionally adhere to various components of the
dishwasher interior, causing temporary discoloration.
To minimize this:
Remove excess tomato-based food soils from
dishes before loading.
Run the Heavy Wash cycle when washing loads
containing tomato-based food soils.
Be sure to use a dishwasher detergent that
contains chlorine to better fight staining.
Standard Exterior
StainJess SteeJ Exterior
[select models]
Light to moderate Soft damp cloth and liquid spray cleaner. De Net use
abrasive powders or cleaning pads.
Daily cleaning and light soil Soft cloth or sponge and one of the following:
Mild detergent and water
A solution of white vinegar and water
Formula 409 Glass and Surface Cleaner*, or similar
multi-surface cleaner.
De Net use products containing chlorine bleach or
citric acid.
Follow with rinse and dry.
Moderate to heavy soil Soft cloth or damp sponge and Bon Ami*. Follow with
rinse and dry.
Streaks or fingerprints/restore shine Soft cloth and Stainless Steel Magic Spray**.
Discoloration Soft cloth or damp sponge and Cameo Stainless Steel
Cleaner*. Rinse immediately and dry.
interior Light to moderate Soft cloth or damp sponge.
Discoloration, or tomato-based stain Switch dishwasher detergent to chlorine-based product.
*Brand names are trademarks of the respective manufacturer.
**Call 1-800-JENNAIR [1-800-536-6247) to order.
Storage/Moving
Fill detergent cup with a fresh-scented dishwasher
detergent or baking soda and select the Normal
Wash cycle. Allow the dishwasher to complete the
cycle. Then turn the water supply off and drain the
dishwasher. To drain, press the START/Cancel pad
once to activate the dishwasher. Press START/Cancel
again to activate the drain (models with cycle selector
knob, turn the cycle selector knob to I:}rain/OFF).
Operate the drain twice to ensure most of the water is
removed. Last, disconnect the electrical supply and
prop open the door.
important: Make sure the water supply to both the
house and dishwasher are turned off.
15
T
CHECK THESE POINTS TO HELP SAVE YOU TiME AND MONEY.
Dishwasher will not fill
Dishwasher will not drain/
Water in tub bottom
Dishwasher adds water at
end of cycle
Detergent cup is not empty
Dishwasher seems noisy
Cycle takes too long CHeating
Delay light [select models]
stays on:}
Dishwasher has an odor
Dishwasher leaks
Press the START/Cancel pad to start the dishwasher.
Be sure door is latched securely.
Be sure the water is turned on.
Check that the pad is properly selected for a cycle.
Check your home's circuit breaker or fuse box.
Check inlet hose for a kink.
Check water valve inlet for sediment and clean if necessary.
If hooked up to a food waste disposer, be sure the knock-out is removed from
the disposer inlet.
Check for food obstruction in the drain or disposer.
Check drain hose for a kink.
Check your home's circuit breaker or fuse box.
Check that the cycle is completed.
This is normal. The sensor (select models) in the pump must stay submerged so
a short fill of water is added after the cycle's last drain.
Check that the cycle is completed.
Be sure dispenser is not blocked.
Use fresh detergent stored in a cool, dry place.
A water valve hiss during fill is normal.
Water circulation sounds are normal.
A thumping sound may be a wash arm bumping an item that is extending
beyond the racks. Readjust load to avoid obstructing wash arm.
Chopping or grinding sounds may be heard as the internal chopper blade chops
hard items like fruit seeds, nuts, etc.
Humming during the drain is normal.
A snap noise is the detergent cup lid hitting the door liner when the dishwasher
door is opened at the end of the cycle. This is normal.
Proper installation affects the noise level.
Super Scrub, Sanitize, or Steam Clean (select models) has been selected and
the cycle is extended to heat water.
Check to see that the incoming water temperature is 120° F (49° C).
iI
iI
Run dishes being held in the dishwasher through a Rinse Only cycle.
Many dishwashers have a "new" smell when first installed.This will dissipate with use.
Dishwasher may not be draining properly. (See Dishwasher Will Not Drain section.)
For a strong odor, place baking soda in both sides of the detergent cup. Select
China/Crystal cycle and allow the water to circulate for about 10 minutes. Interrupt
the cycle by unlatching the door and let it stand overnight. Restart the dishwasher by
latching the door and allow it to complete the cycle. Another alternative is to use a
dishwasher cleaning product such as Jet-Dry Dishwasher Cleane¢.
Check that the dishwasher is level. (Refer to the Installation Instructions.)
Suds can cause the dishwasher to overflow. Measure the detergent carefully and
use only detergents designed for use in a dishwasher. Less detergent is needed
in soft water. Try another brand of detergent if sudsing continues.
Follow directions closely on how to add a forgotten item (pg. 3).
To avoid rinse aid leaking from the dispenser, be sure the lid is securely attached.
*Brand names are trademarks of the respective manufacturer.
Cont.
16
TROU
Display time suddenly drops This is normal when the Sensor Clean (select models) or Normal Wash cycle
or increases by several is selected and the dishwasher decides to skip or add a drain and refill.
minutes [select models)
Indicator lights flashing
Glasses are cloudy/spotted
Food soil remains on dishes
Items washed in the
dishwasher or the dishwasher
tub itself are stained/
discolored
The countdown display (select models) flashes after a cycle is selected until the
START/Cancel pad is pressed.
The countdown display (select models) and the delay indicator flash after a
delay is selected until the START/Cancel pad is pressed.
All active display indicators flash if the door is opened during a running cycle or delay.
The currently selected cycle flashes if an attempt is made to change the cycle
after cycle "lock-in':
The lock indicator flashes and the countdown display (selected models) flashes
an '%' if a pad is pressed while the control lock is enabled.
iI
iI
e
iI
iI
e
iI
iI
e
iI
e
e
e
iI
e
Select Extra Rinse or Hi Temp Wash (select models).
Check water temperature. Incoming water should be 120° F (49° C).
Always use a rinse aid.
Confirm that the cloudiness is removable by soaking the item in white vinegar
for approximately 5 minutes. If removed, the problem isdue to hard water.
Adjust detergent amount being used to match water hardness (pg. 9). Be sure
detergent is fresh, stored properly and is a high quality brand.
If cloudiness is not removable, it is etching. This is an erosion of the surface of
the glassware and can be caused by water that is too hot, from using too much
detergent or by prewashing. Detergent needs food soil to act upon. If etching
has occurred, the glassware is permanently damaged. To prevent further
etching, adjust the detergent amount to match the water hardness, stop
prewashing, and use water heating options only when incoming water
temperature is below 120° F (49° C).
Check water temperature (pg 9).
Run hot water at the sink before starting the dishwasher.
Select Super Scrub, Hi Temp Wash, or Steam Clean option (select models).
Check water hardness and adjust detergent amount accordingly (pg. 9).
Use fresh detergent stored in a cool dry place.
Select proper cycle for the soil level (pg. 10).
Make sure the upper rack wash arm connector is correctly aligned in one of the
water inlet holes (pg. 8).
Load items so they do not block the wash arms (pg. 3-7).
Load the utensil basket with knife handles up and spoon and fork handles
down through the slots in the covers.
Do not place glasses over tines.
Prior to loading, scrape off burnt on foods and wipe the starchy film from
utensils used with pasta, rice and oatmeal. These soils require more energy
than the rest of the load to clean.
Aluminum utensils or pans can leave marks when they rub against other items.
Leave a slight space between items.
Iron deposits in the water can leave a yellow, brown or orange film on dishes orthe
dishwasher tub. A rust filter may be needed, check with a water treatment company.
Separate silver or silver-plated silverware from stainless steel. These metals can
be damaged by contact with each other during washing.
Color from tomato sauces may adhere to the interior parts of the dishwasher
(pg. 15). If light staining has occurred, leave the door open to oxidize the stain
away. Change dishwasher detergent and be sure to use a dishwasher detergent
that contains chlorine to better fight staining.
Certain dishwasher detergents may stain silver. Try another brand of detergent.
*Brand names are trademarks of the respective manufacturer. 17
TROU
items not properly dried/
moisture is present on the
dishwasher interior after the
dry cycle
Be sure Heated Dry isselected.
Water droplets may form on the inner door as part of the drying process.
Use a rinse aid separate from the detergent like Jet Dry* or Cascade Rinse Aid*
regularly, to improve drying. Turn the rinse aid selector toward the MAX setting.
Check water temperature (pg. 9).
Select Sanitize.
Increase detergent amount to match water hardness (pg. 9).
Load properly. (pg. 3-7)
Plastic and items with non-stick surfaces are difficult to dry because they have
a porous surface which tends to collect water droplets. Towel drying may be
necessary.
Glasses and cups with concave bottoms hold water and require towel drying.
Locate these items on the more slanted side of the rack for improved results.
Load dishes according to instructions so they do not strike each other (pg. 3-7).
Washing fine antique china/crystal in the dishwasher is not recommended.
Do not load glasses over the tines.
Do not overload.
Sanitize was not selected.
Sanitization can only be achieved with the Sensor Clean (select models),
Heavy Wash, Normal Wash or China/Crystal cycles.
Sanitization may not be achieved if there is an interruption of the cycle, power
failure or if incoming water temperature is below 120° F (49° C).
Dishware is chipped
=
e
e
Sanitized light does not
illuminate at the end of the
cycle [select models[}
=
Dishwasher door will not Be sure adjustable racks (select models) are properly adjusted to upper or lower
close position (pg. 8).
Brand names are trademarks of the respective manufacturer.
18
JENN-AII DISHWASHERWARRANTY
ONE YEAR LiMiTED WARRANTY
For one year from the date of purchase, when this major appliance is operated and maintained according to instructions attached to or
furnished with the product, JenmAir brand of Maytag Corporation or Maytag Limited (hereafter "JenmAir") will pay for factory specified
replacement parts and repair labor to correct defects in materials or workmanship. Service must be provided by a JenmAir designated
service company. This limited warranty applies only when the major appliance is used in the country in which it is purchased.
SECOND THROUGH FIFTH YEAR LiMiTED WARRANTY ON CERTAIN COMPONENT PARTS
In the second through the fifth year from the date of purchase, when your major appliance is installed, operated and maintained
according to instructions attached to or furnished with the product, JenmAir wilt pay for factory specified parts for the following
components if defective in materials or workmanship: dish racks, all parts of the wash system, drain motor, electronic controls and
heating element. Replacements parts wilt aiso be provided if there is rust including the exterior cabinet and front panels.
LiFETiME LIMITED WARRANTY ON STAINLESS STEEL TUB OR PLASTIC TUB AND iNNER DOOR
For the lifetime of the product from the date of purchase, when your major appliance is installed, operated and maintained according to
instructions attached to or furnished with the product, Jenn-Air wilt pay to replace the dishwasher with the same or similar model if the
tub is defective in materials or workmanship or replace the door liner if it is found to be defective in materials or workmanship.
ITEMS JENN-AIR WILL NOT PAY FOR
1, Service catls to correct the installation of your major appliance, to instruct you how to use your major appliance, to replace or repair
house fuses or to correct house wiring or plumbing.
2. Service calls to repair or replace appliance light bulbs, air filters or water filters. Those consumable parts are excluded from warranty
coverage.
3, Repairs when your major appliance is used for other than normal, single-family household use.
4, Damage resulting from accident, alteration, misuse, abuse, fire, flood, acts of God, improper installation, installation not in
accordance with electrical or plumbing codes, or use of products not approved by Jenn-Air.
5, Replacement parts or repair labor costs for units operated outside the United States or Canada.
6, Pickup and delivery. This major appliance is designed to be repaired in the home.
7. Repairs to parts or systems resulting from unauthorized modifications made to the appliance.
8, Expenses for travel and transportation for product service in remote locations.
9, The removal and reinstattation of your appliance if it is installed in an inaccessible location or is not installed in accordance with
published installation instructions.
10, Replacement parts or repair labor costs when the major appliance is use in a country other than the country in which it was
purchased.
DISCLAIMER OF IMPLIED WARRANTIES; LIMITATION OF REMEDIES
CUSTOMER'S SOLE AND EXCLUSIVE REMEDY UNDER THIS LIMITED WARRANTY SHALL BE PRODUCT REPAIR AS PROVIDED
HEREIN. IMPLIED WARRANTIES, INCLUDING WARRANTIES OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE,
ARE LIMITED TO ONE YEAR OR THE SHORTEST PERIOD ALLOWED BY LAW. JENN-AIR SHALL NOT BE LIABLE FOR INCIDENTAL
OR CONSEQUENTIAL DAMAGES. SOME STATES AND PROVINCES DO NOT ALLOW THE EXCLUSION OR LIMITATION OF
INCIDENTAL OR CONSEQUENTIAL DAMAGES, OR LIMITATIONS ON THE DURATION OF IMPLIED WARRANTIES OF
MERCHANTABILITY OR FITNESS, SO THESE EXCLUSIONS OR LIMITATIONS MAY NOT APPLY TO YOU. THIS WARRANTY GIVES
YOU SPECIFIC LEGAL RIGHTS AND YOU MAY ALSO HAVE OTHER RIGHTS, WHICH VARY FROM STATE TO STATE OR PROVINCE
TO PROVINCE.
Outside the 50 United States and Canada, this warranty does not apply. Contact your authorized Jenn-Air dealer to determine if another
warranty applies.
If you need service, first see the "Troubleshooting" section of the Use & Care Guide. After checking "Troubleshooting," additional help
can be found by checking the "Assistance or Service" section or by calling Jenn-Air. In the U.S.A., call 1-800-JENNAIR
(1-800-536-6247). In Canada, call 1-800-688-2002. 05/07
® Registered Trademark/TM Trademark of Jenn-Air, U.S.A. ©2007. All Rights Reserved.
® Mama Registrada/TM Marca de Fabrica de Jenn-Air, U.S.A. ©2007. Todos los derechos reservados.
MCMarque de commerce/MD Marque d_posee de Jenn-Air, EE.UU. ©2007. Tous droits reserves.
19
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16
  • Page 17 17
  • Page 18 18
  • Page 19 19
  • Page 20 20
  • Page 21 21
  • Page 22 22
  • Page 23 23
  • Page 24 24
  • Page 25 25
  • Page 26 26
  • Page 27 27
  • Page 28 28
  • Page 29 29
  • Page 30 30
  • Page 31 31
  • Page 32 32
  • Page 33 33
  • Page 34 34
  • Page 35 35
  • Page 36 36
  • Page 37 37
  • Page 38 38
  • Page 39 39
  • Page 40 40
  • Page 41 41
  • Page 42 42
  • Page 43 43
  • Page 44 44
  • Page 45 45
  • Page 46 46
  • Page 47 47
  • Page 48 48
  • Page 49 49
  • Page 50 50
  • Page 51 51
  • Page 52 52
  • Page 53 53
  • Page 54 54
  • Page 55 55
  • Page 56 56
  • Page 57 57
  • Page 58 58
  • Page 59 59
  • Page 60 60

Jenn-Air JDB1080AWB36 Le manuel du propriétaire

Catégorie
Lave-vaisselle
Taper
Le manuel du propriétaire