ESAB 250TS 250S PRO-LITE® Inverter Arc Welder Manuel utilisateur

Art # A-04962

PRO-LITE

®

INVERTER ARC WELDER

250TS

Service Manual

Version No: 1 Issue Date: August 9 2005 Manual No.: 0-4753

Operating Features:

250S

WE APPRECIATE YOUR BUSINESS!

Congratulations on your new Thermal Arc product. We are proud

to have you as our customer and will strive to provide you with

the best service and reliability in the industry. This product is backed

by our extensive warranty and world-wide service network. To

locate your nearest distributor or service agency call

1-800-752-7621, or visit us on the web at www.Thermalarc.com.

This Operating Manual has been designed to instruct you on the

correct use and operation of your Thermal Arc product. Your

satisfaction with this product and its safe operation is our ultimate

concern. Therefore please take the time to read the entire manual,

especially the Safety Precautions. They will help you to avoid

potential hazards that may exist when working with this product.

YOU ARE IN GOOD COMPANY!

The Brand of Choice for Contractors and Fabricators Worldwide.

Thermal Arc is a Global Brand of Arc Welding Products for

Thermadyne Industries Inc. We manufacture and supply to major

welding industry sectors worldwide including; Manufacturing,

Construction, Mining, Automotive, Aerospace, Engineering, Rural

and DIY/Hobbyist.

We distinguish ourselves from our competition through market-

leading, dependable products that have stood the test of time. We

pride ourselves on technical innovation, competitive prices,

excellent delivery, superior customer service and technical support,

together with excellence in sales and marketing expertise.

Above all, we are committed to develop technologically advanced

products to achieve a safer working environment within the welding

industry.

WARNINGS

Read and understand this entire Manual and your employer’s safety practices before installing,

operating, or servicing the equipment.

While the information contained in this Manual represents the Manufacturer's best judgement,

the Manufacturer assumes no liability for its use.

250TSand 250S

Inverter Arc Welders

Service Manual Number 0-4753

For the Following Catalog/Part Number:

10-3069: 250TS (208-230 / 460V, 1/3 ph, 50/60 Hz)

10-3068: 250S (208-230 / 460V, 1/3 ph, 50/60 Hz)

Published by:

Thermadyne Corporation

82 Benning Street

West Lebanon, New Hampshire, USA 03784

(603) 298-5711

http://www.thermadyne.com

Thermal Dynamics Corporation

Reproduction of this work, in whole or in part, without written permission of the publisher is prohibited.

The publisher does not assume and hereby disclaims any liability to any party for any loss or damage

caused by any error or omission in this Manual, whether such error results from negligence, accident, or

any other cause.

Publication Date: August 9, 2005

Record the following information for Warranty purposes:

Where Purchased: ___________________________________

Purchase Date: ___________________________________

Equipment Serial #: ___________________________________

i

TABLE OF CONTENTS

SECTION 1:

SAFETY INSTRUCTIONS AND WARNINGS ....................................................... 1-1

1.01 Arc Welding Hazards ...................................................................................... 1-1

1.02 PRINCIPAL SAFETY STANDARDS .................................................................. 1-5

1.03 PRECAUTIONS DE SECURITE EN SOUDAGE A L’ARC .................................... 1-6

1.04 Dangers relatifs au soudage à l’arc................................................................. 1-6

1.05 PRINCIPALES NORMES DE SECURITE ........................................................ 1-10

1.06 LIMITED WARRANTY ................................................................................... 1-11

SECTION 2:

INTRODUCTION ...................................................................................... 2-1

2.01 How To Use This Manual ................................................................................ 2-1

2.02 Equipment Identification................................................................................. 2-1

2.03 Receipt Of Equipment..................................................................................... 2-1

2.04 Symbol Chart ................................................................................................. 2-2

2.05 Scope of Manual ............................................................................................ 2-3

2.06 General Service Philosophy ............................................................................ 2-3

2.03 Service Responsibilities ................................................................................. 2-3

2.04 Specifications ................................................................................................. 2-4

2.05 Electrical Parameters For 250S ...................................................................... 2-5

2.06 Electrical Parameters For 250TS .................................................................... 2-6

2.07 Power Source Features................................................................................... 2-8

2.08 Voltage Reduction Device (VRD) .................................................................... 2-9

SECTION 3:

INSTALLATION ....................................................................................... 3-1

3.01 Switching VRD On/Off .................................................................................... 3-1

3.02 Remote Control Socket .................................................................................. 3-2

SECTION 4:

OPERATION........................................................................................... 4-1

4.01 Welding Parameter Setting (Factory Setting) ................................................. 4-1

SECTION 5:

SERVICE .............................................................................................. 5-1

5.01 Routine Inspection ......................................................................................... 5-1

5.02 General Troubleshooting ................................................................................ 5-2

5.03 Stick Welding Problems ................................................................................. 5-3

5.04 Power Source Problems................................................................................. 5-6

5.05 Error Code Details .......................................................................................... 5-7

TABLE OF CONTENTS (continued)TABLE OF CONTENTS

SECTION 6:

ADVANCED TROUBLESHOOTING GUIDE ......................................................... 6-1

6.01 Test Equipment and Tools .............................................................................. 6-1

6.02 Removing the Enclosure ................................................................................ 6-2

6.03 Visually Inspect .............................................................................................. 6-3

6.04 Advanced Power Source Malfunctions ........................................................... 6-4

6.05 Main PCB PCB1 (WK-4914)Functions and Input/ Outputs ........................... 6-12

6.06 Detection PCB PCB2 (WK-4819) Functions and Inputs/Outputs .................. 6-16

6.07 Connection PCB PCB3 (WK-4921) ............................................................... 6-18

6.08 Secondary Diode PCB PCB4 (WK-4915) (snubber circuit) ........................... 6-22

6.09 Control Source PCB5 (WK-4919) ................................................................. 6-23

6.09 Front Controls PCB PCB6 (WK-4920) .......................................................... 6-26

6.10 Filter 430V PCB PCB7 (WK-4917) ................................................................ 6-27

6.11 Filter PCB PCB11 (WK-5022) ....................................................................... 6-28

6.12 250S, 250TS Control PCB5 (WK-4919) Switch Settings .............................. 6-29

6.13 Test Procedure for Input Rectifier D1 ........................................................... 6-30

6.14 Test Procedure for Input Rectifier D1 ........................................................... 6-32

6.15 Test Procedure for Secondary Diode D2, D3, D4, D5 ................................... 6-34

6.17 High Frequency Points Gap Adjustment. (250TS only)................................. 6-36

6.18 Replacing Pre Charge components on PCB1 (WK-4914) ............................. 6-37

6.19 Replacing Cooling Fan Driver circuit components on PCB3 (WK-4921) ....... 6-38

6.20 Replacing Gas Solenoid Driver circuit components on PCB1

(WK-4914) (250TS only) .............................................................................. 6-39

SECTION 7:

PARTS LIST .......................................................................................... 6-1

7.01 Equipment Identification................................................................................. 6-1

7.02 How To Use This Parts List ............................................................................ 6-1

7.03 250TS Parts List ............................................................................................. 6-2

7.04 250TS Parts Arrangement .............................................................................. 6-4

7.05 250S Parts List ............................................................................................... 6-6

7.06 250S Parts Arrangement ................................................................................ 6-8

APPENDIX 1: GENERAL INFORMATION ................................................................. A-1

APPENDIX 2: 250TS INTERCONNECTION DIAGRAM .................................................. A-2

APPENDIX 3: 250S INTERCONNECTION ................................................................ A-4

PRO-LITE 250TS, 250S

1-1

August 9, 2005

1.01 Arc Welding Hazards

WARNING

ELECTRIC SHOCK can kill.

Touching live electrical parts can cause fatal

shocks or severe burns. The electrode and

work circuit is electrically live whenever the

output is on. The input power circuit and

machine internal circuits are also live when

power is on. In semiautomatic or automatic

wire welding, the wire, wire reel, drive roll

housing, and all metal parts touching the

welding wire are electrically live. Incorrectly

installed or improperly grounded equipment

is a hazard.

1. Do not touch live electrical parts.

2. Wear dry, hole-free insulating gloves and body

protection.

3. Insulate yourself from work and ground using dry

insulating mats or covers.

4. Disconnect input power or stop engine before

installing or servicing this equipment. Lock input

power disconnect switch open, or remove line fuses

so power cannot be turned on accidentally.

5. Properly install and ground this equipment according

to its Owner’s Manual and national, state, and local

codes.

6. Turn off all equipment when not in use. Disconnect

power to equipment if it will be left unattended or out

of service.

7. Use fully insulated electrode holders. Never dip holder

in water to cool it or lay it down on the ground or the

work surface. Do not touch holders connected to two

welding machines at the same time or touch other

people with the holder or electrode.

8. Do not use worn, damaged, undersized, or poorly

spliced cables.

9. Do not wrap cables around your body.

10.Ground the workpiece to a good electrical (earth)

ground.

SECTION 1:

SAFETY INSTRUCTIONS AND WARNINGS

WARNING

PROTECT YOURSELF AND OTHERS FROM POSSIBLE SERIOUS INJURY OR DEATH. KEEP CHILDREN AWAY.

PACEMAKER WEARERS KEEP AWAY UNTIL CONSULTING YOUR DOCTOR. DO NOT LOSE THESE INSTRUCTIONS.

READ OPERATING/INSTRUCTION MANUAL BEFORE INSTALLING, OPERATING OR SERVICING THIS EQUIPMENT.

Welding products and welding processes can cause serious injury or death, or damage to other equipment or property,

if the operator does not strictly observe all safety rules and take precautionary actions.

Safe practices have developed from past experience in the use of welding and cutting. These practices must be

learned through study and training before using this equipment. Some of these practices apply to equipment

connected to power lines; other practices apply to engine driven equipment. Anyone not having extensive

training in welding and cutting practices should not attempt to weld.

Safe practices are outlined in the American National Standard Z49.1 entitled:

SAFETY IN WELDING AND CUTTING.

This publication and other guides to what you should learn before operating this equipment are listed at the end of

these safety precautions. HAVE ALL INSTALLATION, OPERATION, MAINTENANCE, AND REPAIR WORK PERFORMED

ONLY BY QUALIFIED PEOPLE.

PRO-LITE 250TS, 250S

1-2

August 9, 2005

11.Do not touch electrode while in contact with the work

(ground) circuit.

12.Use only well-maintained equipment. Repair or replace

damaged parts at once.

13.In confined spaces or damp locations, do not use a

welder with AC output unless it is equipped with a

voltage reducer. Use equipment with DC output.

14.Wear a safety harness to prevent falling if working

above floor level.

15.Keep all panels and covers securely in place.

WARNING

ARC RAYS can burn eyes and skin; NOISE can

damage hearing.

Arc rays from the welding process produce

intense heat and strong ultraviolet rays that

can burn eyes and skin. Noise from some

processes can damage hearing.

1. Wear a welding helmet fitted with a proper shade of

filter (see ANSI Z49.1 listed in Safety Standards) to

protect your face and eyes when welding or watching.

2. Wear approved safety glasses. Side shields

recommended.

3. Use protective screens or barriers to protect others

from flash and glare; warn others not to watch the

arc.

4. Wear protective clothing made from durable, flame-

resistant material (wool and leather) and foot

protection.

5. Use approved ear plugs or ear muffs if noise level is

high.

WARNING

FUMES AND GASES can be hazardous to your

health.

Welding produces fumes and gases. Breathing

these fumes and gases can be hazardous to

your health.

1. Keep your head out of the fumes. Do not breath the

fumes.

2. If inside, ventilate the area and/or use exhaust at the

arc to remove welding fumes and gases.

3. If ventilation is poor, use an approved air-supplied

respirator.

4. Read the Material Safety Data Sheets (MSDSs) and

the manufacturer’s instruction for metals,

consumables, coatings, and cleaners.

5. Work in a confined space only if it is well ventilated,

or while wearing an air-supplied respirator. Shielding

gases used for welding can displace air causing injury

or death. Be sure the breathing air is safe.

Welding or cutting Electrode Size Filter Welding or cutting Electrode Size Filter

Torch soldering 2

Gas metal-arc

Torch brazing 3 or 4 Non-ferrous base metal All 11

Oxygen Cutting

Ferrous base metal All 12

Light Under 1 in., 25 mm 3 or 4 Gas tungsten arc welding All 12

Medium 1 to 6 in., 25-150 mm 4 or 5 (TIG) All 12

Heavy Over 6 in., 150 mm 5 or 6 Atomic hydrogen welding All 12

Ga s w e lding

Carbon arc welding All 12

Light Under 1/8 in., 3 mm 4 or 5 Plasma arc welding

Medium 1/8 to 1/2 in., 3-12 mm 5 or 6

Carbon arc air gouging

Heavy Over 1/2 in., 12 mm 6 or 8 Light 12

Shielded metal-arc

Under 5/32 in., 4 mm 10 Heavy 14

5/32 to 1/4 in., 12

Plasma arc cutting

Over 1/4 in., 6.4 mm 14 Light Under 300 Amp 9

Medium 300 to 400 Amp 12

Heavy Over 400 Amp 14

Eye protection filter shade selector for welding or cutting

(goggles or helmet), from AWS A6.2-73.

PRO-LITE 250TS, 250S

1-3

August 9, 2005

6. Do not weld in locations near degreasing, cleaning, or

spraying operations. The heat and rays of the arc can

react with vapors to form highly toxic and irritating

gases.

7. Do not weld on coated metals, such as galvanized,

lead, or cadmium plated steel, unless the coating is

removed from the weld area, the area is well ventilated,

and if necessary, while wearing an air-supplied

respirator. The coatings and any metals containing

these elements can give off toxic fumes if welded.

WARNING

WELDING can cause fire or explosion.

Sparks and spatter fly off from the welding

arc. The flying sparks and hot metal, weld

spatter, hot workpiece, and hot equipment can

cause fires and burns. Accidental contact of

electrode or welding wire to metal objects can

cause sparks, overheating, or fire.

1. Protect yourself and others from flying sparks and

hot metal.

2. Do not weld where flying sparks can strike flammable

material.

3. Remove all flammables within 35 ft (10.7 m) of the

welding arc. If this is not possible, tightly cover them

with approved covers.

4. Be alert that welding sparks and hot materials from

welding can easily go through small cracks and

openings to adjacent areas.

5. Watch for fire, and keep a fire extinguisher nearby.

6. Be aware that welding on a ceiling, floor, bulkhead, or

partition can cause fire on the hidden side.

7. Do not weld on closed containers such as tanks or

drums.

8. Connect work cable to the work as close to the welding

area as practical to prevent welding current from

traveling long, possibly unknown paths and causing

electric shock and fire hazards.

9. Do not use welder to thaw frozen pipes.

10.Remove stick electrode from holder or cut off welding

wire at contact tip when not in use.

WARNING

FLYING SPARKS AND HOT METAL can cause

injury.

Chipping and grinding cause flying metal. As

welds cool, they can throw off slag.

1. Wear approved face shield or safety goggles. Side

shields recommended.

2. Wear proper body protection to protect skin.

WARNING

CYLINDERS can explode if damaged.

Shielding gas cylinders contain gas under high

pressure. If damaged, a cylinder can explode.

Since gas cylinders are normally part of the

welding process, be sure to treat them

carefully.

1. Protect compressed gas cylinders from excessive heat,

mechanical shocks, and arcs.

2. Install and secure cylinders in an upright position by

chaining them to a stationary support or equipment

cylinder rack to prevent falling or tipping.

3. Keep cylinders away from any welding or other

electrical circuits.

4. Never allow a welding electrode to touch any cylinder.

5. Use only correct shielding gas cylinders, regulators,

hoses, and fittings designed for the specific

application; maintain them and associated parts in

good condition.

6. Turn face away from valve outlet when opening

cylinder valve.

7. Keep protective cap in place over valve except when

cylinder is in use or connected for use.

8. Read and follow instructions on compressed gas

cylinders, associated equipment, and CGA publication

P-1 listed in Safety Standards.

PRO-LITE 250TS, 250S

1-4

August 9, 2005

WARNING

Engines can be dangerous.

WARNING

ENGINE EXHAUST GASES can kill.

Engines produce harmful exhaust gases.

1. Use equipment outside in open, well-ventilated areas.

2. If used in a closed area, vent engine exhaust outside

and away from any building air intakes.

WARNING

ENGINE FUEL can cause fire or explosion.

Engine fuel is highly flammable.

1. Stop engine before checking or adding fuel.

2. Do not add fuel while smoking or if unit is near any

sparks or open flames.

3. Allow engine to cool before fueling. If possible, check

and add fuel to cold engine before beginning job.

4. Do not overfill tank — allow room for fuel to expand.

5. Do not spill fuel. If fuel is spilled, clean up before

starting engine.

WARNING

MOVING PARTS can cause injury.

Moving parts, such as fans, rotors, and belts can cut

fingers and hands and catch loose clothing.

1. Keep all doors, panels, covers, and guards closed

and securely in place.

2. Stop engine before installing or connecting unit.

3. Have only qualified people remove guards or

covers for maintenance and troubleshooting as

necessary.

4. To prevent accidental starting during servicing,

disconnect negative (-) battery cable from battery.

5. Keep hands, hair, loose clothing, and tools away

from moving parts.

6. Reinstall panels or guards and close doors when

servicing is finished and before starting engine.

WARNING

SPARKS can cause BATTERY GASES TO

EXPLODE; BATTERY ACID can burn eyes and

skin.

Batteries contain acid and generate explosive gases.

1. Always wear a face shield when working on a battery.

2. Stop engine before disconnecting or connecting

battery cables.

3. Do not allow tools to cause sparks when working on

a battery.

4. Do not use welder to charge batteries or jump start

vehicles.

5. Observe correct polarity (+ and –) on batteries.

WARNING

STEAM AND PRESSURIZED HOT COOLANT

can burn face, eyes, and skin.

The coolant in the radiator can be very hot

and under pressure.

1. Do not remove radiator cap when engine is hot. Allow

engine to cool.

2. Wear gloves and put a rag over cap area when

removing cap.

3. Allow pressure to escape before completely removing

cap.

PRO-LITE 250TS, 250S

1-5

August 9, 2005

WARNING

This product, when used for welding or

cutting, produces fumes or gases which

contain chemicals know to the State of

California to cause birth defects and, in some

cases, cancer. (California Health & Safety code

Sec. 25249.5 et seq.)

NOTE

Considerations About Welding And The Effects

of Low Frequency Electric and Magnetic Fields

The following is a quotation from the General Conclusions

Section of the U.S. Congress, Office of Technology

Assessment,

Biological Effects of Power

Frequency Electric & Magnetic Fields - Background Paper,

OTA-BP-E-63 (Washington, DC: U.S. Government Printing

Office, May 1989): “...there is now a very large volume of

scientific findings based on experiments at the cellular

level and from studies with animals and people which

clearly establish that low frequency magnetic fields and

interact with, and produce changes in, biological systems.

While most of this work is of very high quality, the results

are complex. Current scientific understanding does not

yet allow us to interpret the evidence in a single coherent

framework. Even more frustrating, it does not yet allow

us to draw definite conclusions about questions of

possible risk or to offer clear science-based advice on

strategies to minimize or avoid potential risks.”

To reduce magnetic fields in the workplace, use the

following procedures.

1. Keep cables close together by twisting or taping

them.

2. Arrange cables to one side and away from the

operator.

3. Do not coil or drape cable around the body.

4. Keep welding power source and cables as far away

from body as practical.

ABOUT PACEMAKERS:

The above procedures are among those also

normally recommended for pacemaker

wearers. Consult your doctor for complete

information.

1.02 PRINCIPAL SAFETY STANDARDS

Safety in Welding and Cutting, ANSI Standard Z49.1, from

American Welding Society, 550 N.W. LeJeune Rd., Miami,

FL 33126.

Safety and Health Standards, OSHA 29 CFR 1910, from

Superintendent of Documents, U.S. Government Printing

Office, Washington, D.C. 20402.

Recommended Safe Practices for the Preparation for

Welding and Cutting of Containers That Have Held

Hazardous Substances, American Welding Society

Standard AWS F4.1, from American Welding Society, 550

N.W. LeJeune Rd., Miami, FL 33126.

National Electrical Code, NFPA Standard 70, from National

Fire Protection Association, Batterymarch Park, Quincy,

MA 02269.

Safe Handling of Compressed Gases in Cylinders, CGA

Pamphlet P-1, from Compressed Gas Association, 1235

Jefferson Davis Highway, Suite 501, Arlington, VA 22202.

Code for Safety in Welding and Cutting, CSA Standard

W117.2, from Canadian Standards Association, Standards

Sales, 178 Rexdale Boulevard, Rexdale, Ontario, Canada

M9W 1R3.

Safe Practices for Occupation and Educational Eye and

Face Protection, ANSI Standard Z87.1, from American

National Standards Institute, 1430 Broadway, New York,

NY 10018.

Cutting and Welding Processes, NFPA Standard 51B, from

National Fire Protection Association, Batterymarch Park,

Quincy, MA 02269.

PRO-LITE 250TS, 250S

1-6

August 9, 2005

1.03 PRECAUTIONS DE SECURITE EN SOUDAGE A L’ARC

MISE EN GARDE

LE SOUDAGE A L’ARC EST DANGEREUX

PROTEGEZ-VOUS, AINSI QUE LES AUTRES, CONTRE LES BLESSURES GRAVES POSSIBLES OU LA MORT. NE LAISSEZ

PAS LES ENFANTS S’APPROCHER, NI LES PORTEURS DE STIMULATEUR CARDIAQUE (A MOINS QU’ILS N’AIENT

CONSULTE UN MEDECIN). CONSERVEZ CES INSTRUCTIONS. LISEZ LE MANUEL D’OPERATION OU LES INSTRUC-

TIONS AVANT D’INSTALLER, UTILISER OU ENTRETENIR CET EQUIPEMENT.

Les produits et procédés de soudage peuvent sauser des blessures graves ou la mort, de même que des dommages

au reste du matériel et à la propriété, si l’utilisateur n’adhère pas strictement à toutes les règles de sécurité et ne prend

pas les précautions nécessaires.

En soudage et coupage, des pratiques sécuritaires se sont développées suite à l’expérience passée. Ces pratiques

doivent être apprises par étude ou entraînement avant d’utiliser l’equipement. Toute personne n’ayant pas suivi un

entraînement intensif en soudage et coupage ne devrait pas tenter de souder. Certaines pratiques concernent les

équipements raccordés aux lignes d’alimentation alors que d’autres s’adressent aux groupes électrogènes.

La norme Z49.1 de l’American National Standard, intitulée “SAFETY IN WELDING AND CUTTING” présente les pra-

tiques sécuritaires à suivre. Ce document ainsi que d’autres guides que vous devriez connaître avant d’utiliser cet

équipement sont présentés à la fin de ces instructions de sécurité.

SEULES DES PERSONNES QUALIFIEES DOIVENT FAIRE

DES TRAVAUX D’INSTALLATION, DE REPARATION,

D’ENTRETIEN ET D’ESSAI.

1.04 Dangers relatifs au soudage à l’arc

AVERTISSEMENT

L’ELECTROCUTION PEUT ETRE MORTELLE.

Une décharge électrique peut tuer ou brûler

gravement. L’électrode et le circuit de soudage

sont sous tension dès la mise en circuit. Le

circuit d’alimentation et les circuits internes

de l’équipement sont aussi sous tension dès

la mise en marche. En soudage automatique

ou semi-automatique avec fil, ce dernier, le

rouleau ou la bobine de fil, le logement des

galets d’entrainement et toutes les pièces

métalliques en contact avec le fil de soudage

sont sous tension. Un équipement

inadéquatement installé ou inadéquatement

mis à la terre est dangereux.

1. Ne touchez pas à des pièces sous tension.

2. Portez des gants et des vêtements isolants, secs et

non troués.

3 Isolez-vous de la pièce à souder et de la mise à la

terre au moyen de tapis isolants ou autres.

4. Déconnectez la prise d’alimentation de l’équipement

ou arrêtez le moteur avant de l’installer ou d’en faire

l’entretien. Bloquez le commutateur en circuit ouvert

ou enlevez les fusibles de l’alimentation afin d’éviter

une mise en marche accidentelle.

5. Veuillez à installer cet équipement et à le mettre à la

terre selon le manuel d’utilisation et les codes

nationaux, provinciaux et locaux applicables.

6. Arrêtez tout équipement après usage. Coupez

l’alimentation de l’équipement s’il est hors d’usage

ou inutilisé.

7. N’utilisez que des porte-électrodes bien isolés. Ne

jamais plonger les porte-électrodes dans l’eau pour

les refroidir. Ne jamais les laisser traîner par terre ou

sur les pièces à souder. Ne touchez pas aux porte-

électrodes raccordés à deux sources de courant en

même temps. Ne jamais toucher quelqu’un d’autre

avec l’électrode ou le porte-électrode.

8. N’utilisez pas de câbles électriques usés,

endommagés, mal épissés ou de section trop petite.

9. N’enroulez pas de câbles électriques autour de votre

corps.

PRO-LITE 250TS, 250S

1-7

August 9, 2005

10.N’utilisez qu’une bonne prise de masse pour la mise à

la terre de la pièce à souder.

11.Ne touchez pas à l’électrode lorsqu’en contact avec le

circuit de soudage (terre).

12.N’utilisez que des équipements en bon état. Réparez

ou remplacez aussitôt les pièces endommagées.

13.Dans des espaces confinés ou mouillés, n’utilisez pas

de source de courant alternatif, à moins qu’il soit muni

d’un réducteur de tension. Utilisez plutôt une source

de courant continu.

14.Portez un harnais de sécurité si vous travaillez en hau-

teur.

15.Fermez solidement tous les panneaux et les capots.

AVERTISSEMENT

LE RAYONNEMENT DE L’ARC PEUT BRÛLER

LES YEUX ET LA PEAU; LE BRUIT PEUT

ENDOMMAGER L’OUIE.

L’arc de soudage produit une chaleur et des

rayons ultraviolets intenses, susceptibles de

brûler les yeux et la peau. Le bruit causé par

certains procédés peut endommager l’ouïe.

1. Portez une casque de soudeur avec filtre oculaire de

nuance appropriée (consultez la norme ANSI Z49

indiquée ci-après) pour vous protéger le visage et les

yeux lorsque vous soudez ou que vous observez

l’exécution d’une soudure.

2. Portez des lunettes de sécurité approuvées. Des écrans

latéraux sont recommandés.

3. Entourez l’aire de soudage de rideaux ou de cloisons

pour protéger les autres des coups d’arc ou de

l’éblouissement; avertissez les observateurs de ne pas

regarder l’arc.

4. Portez des vêtements en matériaux ignifuges et

durables (laine et cuir) et des chaussures de sécurité.

5. Portez un casque antibruit ou des bouchons d’oreille

approuvés lorsque le niveau de bruit est élevé.

AVERTISSEMENT

LES VAPEURS ET LES FUMEES SONT

DANGEREUSES POUR LA SANTE.

Le soudage dégage des vapeurs et des fumées

dangereuses à respirer.

Opération de coupage

ou soudage

Dimension d'électrode ou

Epiasseur de métal ou

Intensité de courant

Nuance de

filtre oculaire

Opération de coupage

ou soudage

Dimension d'électrode ou

Epiasseur de métal ou

Intensité de courant

Nuance de

filtre oculaire

Brassage tendre

au chalumeau

toutes conditions 2

Soudage á l'arc sous gaz

avec fil plein (GMAW)

Brassage fort

au chalumeau

toutes conditions 3 ou 4 métaux non-ferreux toutes conditions 11

Oxycoupage métaux ferreux toutes conditions 12

mince moins de 1 po. (25 mm) 2 ou 3

Soudage á l'arc sous gaz avec

électrode de tungstène (GTAW)

toutes conditions 12

moyen de 1 á 6 po. (25 á 150 mm) 4 ou 5

Soudage á l'hydrogène

atomique (AHW)

toutes conditions 12

épais plus de 6 po. (150 mm) 5 ou 6

Soudage á l'arc avec

électrode de carbone (CAW)

toutes conditions 12

Soudage aux gaz Soudage á l'arc Plasma (PAW) toutes dimensions 12

mince moins de 1/8 po. (3 mm) 4 ou 5

Gougeage Air-Arc avec

électrode de carbone

moyen de 1/8 á 1/2 po. (3 á 12 mm) 5 ou 6 mince 12

épais plus de 1/2 po. (12 mm) 6 ou 8 épais 14

Soudage á l'arc avec

électrode enrobees

(SMAW)

moins de 5/32 po. (4 mm) 10 Coupage á l'arc Plasma (PAC)

5/32 á 1/4 po. (4 á 6.4 mm) 12 mince moins de 300 amperès 9

plus de 1/4 po. (6.4 mm) 14 moyen de 300 á 400 amperès 12

épais plus de 400 amperès 14

SELECTION DES NUANCES DE FILTRES OCULAIRS POUR LA PROTECTION

DES YEUX EN COUPAGE ET SOUDAGE (selon AWS á 8.2-73)

PRO-LITE 250TS, 250S

1-8

August 9, 2005

1. Eloignez la tête des fumées pour éviter de les respirer.

2. A l’intérieur, assurez-vous que l’aire de soudage est

bien ventilée ou que les fumées et les vapeurs sont

aspirées à l’arc.

3. Si la ventilation est inadequate, portez un respirateur

à adduction d’air approuvé.

4. Lisez les fiches signalétiques et les consignes du

fabricant relatives aux métaux, aux produits

consummables, aux revêtements et aux produits

nettoyants.

5. Ne travaillez dans un espace confiné que s’il est bien

ventilé; sinon, portez un respirateur à adduction d’air.

Les gaz protecteurs de soudage peuvent déplacer

l’oxygène de l’air et ainsi causer des malaises ou la

mort. Assurez-vous que l’air est propre à la respira-

tion.

6. Ne soudez pas à proximité d’opérations de

dégraissage, de nettoyage ou de pulvérisation. La

chaleur et les rayons de l’arc peuvent réagir avec des

vapeurs et former des gaz hautement toxiques et irri-

tants.

7. Ne soudez des tôles galvanisées ou plaquées au plomb

ou au cadmium que si les zones à souder ont été

grattées à fond, que si l’espace est bien ventilé; si

nécessaire portez un respirateur à adduction d’air. Car

ces revêtements et tout métal qui contient ces

éléments peuvent dégager des fumées toxiques au

moment du soudage.

AVERTISSEMENT

LE SOUDAGE PEUT CAUSER UN INCENDIE OU

UNE EXPLOSION

L’arc produit des étincellies et des projections.

Les particules volantes, le métal chaud, les

projections de soudure et l’équipement

surchauffé peuvent causer un incendie et des

brûlures. Le contact accidentel de l’électrode

ou du fil-électrode avec un objet métallique

peut provoquer des étincelles, un

échauffement ou un incendie.

1. Protégez-vous, ainsi que les autres, contre les

étincelles et du métal chaud.

2. Ne soudez pas dans un endroit où des particules

volantes ou des projections peuvent atteindre des

matériaux inflammables.

3. Enlevez toutes matières inflammables dans un rayon

de 10, 7 mètres autour de l’arc, ou couvrez-les

soigneusement avec des bâches approuvées.

4. Méfiez-vous des projections brulantes de soudage

susceptibles de pénétrer dans des aires adjacentes

par de petites ouvertures ou fissures.

5. Méfiez-vous des incendies et gardez un extincteur à

portée de la main.

6. N’oubliez pas qu’une soudure réalisée sur un plafond,

un plancher, une cloison ou une paroi peut enflammer

l’autre côté.

7. Ne soudez pas un récipient fermé, tel un réservoir ou

un baril.

8. Connectez le câble de soudage le plus près possible

de la zone de soudage pour empêcher le courant de

suivre un long parcours inconnu, et prévenir ainsi les

risques d’électrocution et d’incendie.

9. Ne dégelez pas les tuyaux avec un source de courant.

10.Otez l’électrode du porte-électrode ou coupez le fil au

tube-contact lorsqu’inutilisé après le soudage.

11.Portez des vêtements protecteurs non huileux, tels

des gants en cuir, une chemise épaisse, un pantalon

revers, des bottines de sécurité et un casque.

AVERTISSEMENT

LES ETINCELLES ET LES PROJECTIONS

BRULANTES PEUVENT CAUSER DES

BLESSURES.

Le piquage et le meulage produisent des

particules métalliques volantes. En

refroidissant, la soudure peut projeter du

éclats de laitier.

1. Portez un écran facial ou des lunettes protectrices

approuvées. Des écrans latéraux sont

recommandés.

2. Portez des vêtements appropriés pour protéger

la peau.

PRO-LITE 250TS, 250S

1-9

August 9, 2005

AVERTISSEMENT

LES BOUTEILLES ENDOMMAGEES PEUVENT

EXPLOSER

Les bouteilles contiennent des gaz protecteurs

sous haute pression. Des bouteilles

endommagées peuvent exploser. Comme les

bouteilles font normalement partie du procédé

de soudage, traitez-les avec soin.

1. Protégez les bouteilles de gaz comprimé contre les

sources de chaleur intense, les chocs et les arcs de

soudage.

2. Enchainez verticalement les bouteilles à un support

ou à un cadre fixe pour les empêcher de tomber ou

d’être renversées.

3. Eloignez les bouteilles de tout circuit électrique ou de

tout soudage.

4. Empêchez tout contact entre une bouteille et une

électrode de soudage.

5. N’utilisez que des bouteilles de gaz protecteur, des

détendeurs, des boyauxs et des raccords conçus pour

chaque application spécifique; ces équipements et les

pièces connexes doivent être maintenus en bon état.

6. Ne placez pas le visage face à l’ouverture du robinet

de la bouteille lors de son ouverture.

7. Laissez en place le chapeau de bouteille sauf si en

utilisation ou lorsque raccordé pour utilisation.

8. Lisez et respectez les consignes relatives aux bouteilles

de gaz comprimé et aux équipements connexes, ainsi

que la publication P-1 de la CGA, identifiée dans la

liste de documents ci-dessous.

AVERTISSEMENT

LES MOTEURS PEUVENT ETRE DANGEREUX

LES GAZ D’ECHAPPEMENT DES MOTEURS

PEUVENT ETRE MORTELS.

Les moteurs produisent des gaz d’échappement nocifs.

1. Utilisez l’équipement à l’extérieur dans des aires

ouvertes et bien ventilées.

2. Si vous utilisez ces équipements dans un endroit

confiné, les fumées d’échappement doivent être

envoyées à l’extérieur, loin des prises d’air du bâtiment.

AVERTISSEMENT

LE CARBURANT PEUR CAUSER UN INCENDIE

OU UNE EXPLOSION.

Le carburant est hautement inflammable.

1. Arrêtez le moteur avant de vérifier le niveau e

carburant ou de faire le plein.

2. Ne faites pas le plein en fumant ou proche d’une source

d’étincelles ou d’une flamme nue.

3. Si c’est possible, laissez le moteur refroidir avant de

faire le plein de carburant ou d’en vérifier le niveau au

début du soudage.

4. Ne faites pas le plein de carburant à ras bord: prévoyez

de l’espace pour son expansion.

5. Faites attention de ne pas renverser de carburant.

Nettoyez tout carburant renversé avant de faire

démarrer le moteur.

AVERTISSEMENT

DES PIECES EN MOUVEMENT PEUVENT

CAUSER DES BLESSURES.

Des pièces en mouvement, tels des

ventilateurs, des rotors et des courroies

peuvent couper doigts et mains, ou accrocher

des vêtements amples.

1. Assurez-vous que les portes, les panneaux, les capots

et les protecteurs soient bien fermés.

2. Avant d’installer ou de connecter un système, arrêtez

le moteur.

3. Seules des personnes qualifiées doivent démonter des

protecteurs ou des capots pour faire l’entretien ou le

dépannage nécessaire.

PRO-LITE 250TS, 250S

1-10

August 9, 2005

4. Pour empêcher un démarrage accidentel pendant

l’entretien, débranchez le câble d’accumulateur à la

borne négative.

5. N’approchez pas les mains ou les cheveux de pièces

en mouvement; elles peuvent aussi accrocher des

vêtements amples et des outils.

6. Réinstallez les capots ou les protecteurs et fermez les

portes après des travaux d’entretien et avant de faire

démarrer le moteur.

AVERTISSEMENT

DES ETINCELLES PEUVENT FAIRE EXPLOSER

UN ACCUMULATEUR; L’ELECTROLYTE D’UN

ACCUMU-LATEUR PEUT BRULER LA PEAU ET

LES YEUX.

Les accumulateurs contiennent de l’électrolyte

acide et dégagent des vapeurs explosives.

1. Portez toujours un écran facial en travaillant sur un

accumu-lateur.

2. Arrêtez le moteur avant de connecter ou de

déconnecter des câbles d’accumulateur.

3. N’utilisez que des outils anti-étincelles pour travailler

sur un accumulateur.

4. N’utilisez pas une source de courant de soudage pour

charger un accumulateur ou survolter

momentanément un véhicule.

5. Utilisez la polarité correcte (+ et –) de l’accumulateur.

AVERTISSEMENT

LA VAPEUR ET LE LIQUIDE DE

REFROIDISSEMENT BRULANT SOUS

PRESSION PEUVENT BRULER LA PEAU ET

LES YEUX.

Le liquide de refroidissement d’un radiateur

peut être brûlant et sous pression.

1. N’ôtez pas le bouchon de radiateur tant que le moteur

n’est pas refroidi.

2. Mettez des gants et posez un torchon sur le bouchon

pour l’ôter.

3. Laissez la pression s’échapper avant d’ôter

complètement le bouchon.

1.05 PRINCIPALES NORMES DE

SECURITE

Safety in Welding and Cutting, norme ANSI Z49.1, American

Welding Society, 550 N.W. LeJeune Rd., Miami, FL 33128.

Safety and Health Standards, OSHA 29 CFR 1910, Superintendent

of Documents, U.S. Government Printing Office, Washington, D.C.

20402.

Recommended Safe Practices for the Preparation for Welding and

Cutting of Containers That Have Held Hazardous Substances,

norme AWS F4.1, American Welding Society, 550 N.W. LeJeune

Rd., Miami, FL 33128.

National Electrical Code, norme 70 NFPA, National Fire Protection

Association, Batterymarch Park, Quincy, MA 02269.

Safe Handling of Compressed Gases in Cylinders, document P-1,

Compressed Gas Association, 1235 Jefferson Davis Highway, Suite

501, Arlington, VA 22202.

Code for Safety in Welding and Cutting, norme CSA W117.2

Association canadienne de normalisation, Standards Sales, 276

Rexdale Boulevard, Rexdale, Ontario, Canada M9W 1R3.

Safe Practices for Occupation and Educational Eye and Face

Protection, norme ANSI Z87.1, American National Standards

Institute, 1430 Broadway, New York, NY 10018.

Cutting and Welding Processes, norme 51B NFPA, National Fire

Protection Association, Batterymarch Park, Quincy, MA 02269.

PRO-LITE 250TS, 250S

1-11

August 9, 2005

1.06 LIMITED WARRANTY

LIMITED WARRANTY: Thermal Arc®, Inc., A Thermadyne Company, hereafter, “Thermal Arc” warrants to customers of itsauthorized distributors

hereafter “Purchaser” that its products will be free of defects in workmanship or material. Should anyfailure to conform to this warranty appear within

the time period applicable to the Thermal Arc products as stated below, Thermal Arc shall, upon notification thereof and substantiation that the product

has been stored, installed, operated, and maintained in accordance with Thermal Arc’s specifications, instructions, recommendations and recognized

standard industry practice, and not subject to misuse, repair, neglect, alteration, or accident, correct such defects by suitable repair or replacement, at

Thermal Arc’s sole option, of any components or parts of the product determined by Thermal Arc to be defective.

THERMAL ARC MAKES NO OTHER WARRANTY, EXPRESS OR IMPLIED. THIS WARRANTY IS EXCLUSIVE AND IN LIEU OF ALL OTHERS, INCLUDING,

BUT NOT LIMITED TO ANY WARRANTY OF MERCHANTABILITY OR FITNESS FOR ANY PARTICULAR PURPOSE.

LIMITATION OF LIABILITY: THERMAL ARC SHALL NOT UNDER ANY CIRCUMSTANCES BE LIABLE FOR SPECIAL, INDIRECT OR CONSEQUENTIAL

DAMAGES, SUCH AS, BUT NOT LIMITED TO, LOST PROFITS AND BUSINESS INTERRUPTION. The remedies of the Purchaser set forth herein are

exclusive and the liability of Thermal Arc with respect to any contract, or anything done in connection therewith such as the performance or breach

thereof, or from the manufacture, sale, delivery, resale, or use of any goods covered by or furnished by Thermal Arc whether arising out of contract,

negligence, strict tort, or under any warranty, or otherwise, shall not, except as expressly provided herein, exceed the price of the goods upon which

such liability is based. No employee, agent, or representative of Thermal Arc is authorized to change this warranty in any way or grant any other

warranty.

PURCHASER’S RIGHTS UNDER THIS WARRANTY ARE VOID IF REPLACEMENT PARTS OR ACCESSORIES ARE USED WHICH IN THERMAL ARC’S SOLE

JUDGEMENT MAY IMPAIR THE SAFETY OR PERFORMANCE OF ANY THERMAL ARC PRODUCT. PURCHASER’S RIGHTS UNDER THIS WARRANTY ARE

VOID IF THE PRODUCT IS SOLD TO PURCHASER BY NON-AUTHORIZED PERSONS.

The warranty is effective for the time stated below beginning on the date that the authorized distributor delivers the products to the Purchaser.

Notwithstanding the foregoing, in no event shall the warranty period extend more than the time stated plus one year from the date Thermal Arc

delivered the product to the authorized distributor.

POWER SUPPLIES

ALL OTHER

LABOR

POWER SUPPLIES

MAIN POWER MAGNETICS (STATIC & ROTATING) 3 YEARS 3 YEAR

ORIGINAL MAIN POWER RECTIFIER 3 YEARS 3 YEAR

CONTROL PC BOARD 3 YEARS 3 YEAR

ALL OTHER CIRCUITS AND COMPONENTS INCLUDING BUT

NOT LIMITED TO: CONTACTORS, RELAYS, SOLENOIDS, PUMPS,

POWER SWITCHING SEMI-CONDUCTORS.

ENGINES: ENGINES ARE NOT WARRANTED BY THERMAL ARC,

ALTHOUGH MOST ARE WARRANTED BY THE ENGINE

MANUFACTURER. SEE THE ENGINE MANUFACTURE'S 1 YEAR 1 YEAR

WARRANTY FOR DETAILS.

CONSOLES, CONTROL EQUIPMENT, HEAT EXCHANGES

ACCESSORY EQUIPMENT

1 YEAR 1 YEAR

NOTE: Dragster 85® excluded from this policy. Refer to Dragster 85 warranty in Dragster 85 Owner’s Manual.

Warranty repairs or replacement claims under this limited warranty must be submitted to Thermal Arc by an authorized Thermal Arc repair facility

within thirty (30) days of purchaser’s notice of any Warranty Claim. No transportation costs of any kind will be paid under this warranty. Transportation

charges to send products to an authorized warranty repair facility shall be the responsibility of the Purchaser. All returned goods shall be at the

Purchaser’s risk and expense. This warranty supersedes all previous Thermal Arc warranties. Thermal Arc® is a Registered Trademark of Thermadyne

Industries Inc.

September 27, 2004

PRO-LITE 250TS, 250S

1-12

August 9, 2005

PRO-LITE 250TS, 250S

August 9, 2005

2-1

SECTION 2:

INTRODUCTION

2.01 How To Use This Manual

This Service Manual applies to just specifications or part

numbers listed on page i.

To ensure safe operation, read the entire manual, including

the chapter on safety instructions and warnings.

Throughout this manual, the words WARNING,

CAUTION, and NOTE may appear. Pay particular attention

to the information provided under these headings. These

special annotations are easily recognized as

follows:

WARNING

A WARNING gives information regarding

possible personal injury.

CAUTION

A CAUTION refers to possible equipment

damage.

NOTE

A NOTE offers helpful information concerning

certain operating procedures.

Additional copies of this manual may be purchased by

contacting Thermal Arc at the address and phone number

given in the next section. Include the Owner’s Manual

number and equipment identification numbers.

Electronic copies of this manual can also be downloaded

at no charge in Acrobat PDF format by going to the

Thermal Arc web site listed below and clicking on the

Literature Library link:

http://www.thermalarc.com

2.02 Equipment Identification

The unit’s identification number (specification or part

number), model, and serial number usually appear on a

nameplate attached to the control panel. In some cases,

the nameplate may be attached to the rear panel.

Equipment which does not have a control panel such as

gun and cable assemblies is identified only by the

specification or part number printed on the shipping

container. Record these numbers on the bottom of page

1 for future reference.

2.03 Receipt Of Equipment

When you receive the equipment, check it against the

invoice to make sure it is complete and inspect the

equipment for possible damage due to shipping. If there

is any damage, notify the carrier immediately to file a

claim. Furnish complete information concerning damage

claims or shipping errors to the location in your area

listed in the inside back cover of this manual.

Include all equipment identification numbers as described

above along with a full description of the parts in error.

Move the equipment to the installation site before un-

crating the unit. Use care to avoid damaging the

equipment when using bars, hammers, etc., to un-crate

the unit.

PRO-LITE 250TS, 250S

2-2

August 9, 2005

2.04 Symbol Chart

Note that only some of these symbols will appear on your model.

Gas Tungsten Arc

Welding (GTAW)

Air Carbon Arc

Cutting (CAC-A)

Constant Current

Constant Voltage

Or Constant Potential

High Temperature

Fault Indication

Arc Force

Touch Start (GTAW)

Variable Inductance

Voltage Input

Single Phase

Three Phase

Three Phase Static

Frequency Converter-

Transformer-Rectifier

Dangerous Voltage

Off

On

Panel/Local

Shielded Metal

Arc Welding (SMAW)

Gas Metal Arc

Welding (GMAW)

Increase/Decrease

Circuit Breaker

AC Auxiliary Power

Remote

Duty Cycle

Percentage

Amperage

Voltage

Hertz (cycles/sec)

Frequency

Negative

Positive

Direct Current (DC)

Protective Earth

(Ground)

Line

Line Connection

Auxiliary Power

Receptacle Rating-

Auxiliary Power

Art # A-04130

115V 15A

t

t1

t2

%

X

IPM

MPM

t

V

Fuse

Wire Feed Function

Wire Feed Towards

Workpiece With

Output Voltage Off.

Preflow Time

Postflow Time

Spot Time

Spot Weld Mode

Continuous Weld

Mode

Press to initiate wirefeed and

welding, release to stop.

Purging Of Gas

Inches Per Minute

Meters Per Minute

Disturbance In

Ground System

Welding Gun

Burnback Time

Press and hold for preflow, release

to start arc. Press to stop arc, and

hold for preflow.

4 Step Trigger

Operation

2 Step Trigger

Operation

La page est en cours de chargement...

ESAB 250TS 250S PRO-LITE® Inverter Arc Welder Manuel utilisateur

ESAB 250TS 250S PRO-LITE® Inverter Arc Welder Manuel utilisateur

dans d''autres langues

Documents connexes

Autres documents