EDOBE XDOM SUBWOOFER Le manuel du propriétaire

1

OWNER’S MANUAL

and installation instructions

State-of-the-Art Wireless SubWoofer

Installs in 5 minutes or less!

NOTE: This SubWoofer can only be used with the ebode wireless LightSpeaker

®

transmitter.

It cannot be used or operated without the LightSpeaker

®

transmitter.

User guide 2

Bedienungsanleitung 18

Gebruiksaanwijzing 34

Användermanual 50

Guide utilisateur 66

Guía del usuario 82

Manual do utilizador 98

Manuale per l’utente 114

2

The exclamation point, within an equilateral triangle, is intended to alert the user to the

presence of important operating and maintenance (servicing) instructions in the literature

accompanying the product.

The lightening ﬂash with arrowhead symbol within an equilateral triangle, is intended to

alert the user to the presence of uninsulated “dangerous voltage” within the product’s

enclosure that may be of sufﬁcient magnitude to constitute a risk of electrical shock to

persons.

WARNING: To reduce the risk of ﬁre or electrical shock, do not expose this apparatus to rain or

moisture.

WARNING No naked ﬂame sources - such as candles - should be placed on the product.

WARNING - Do not open! Risk of electrical shock. Voltages in this equipment are hazardous to life. No

user-serviceable parts inside. Refer all servicing to qualiﬁed service personnel.

Place the equipment near a main power supply outlet and make sure that you can easily access the

power breaker switch.

WARNING: This product is intended to be operated ONLY from the AC Voltages listed on the back

panel or included power supply of the product. Operation from voltages other than those indicated

may cause irreversible damage to the product and void the product’s warranty. The use of AC Plug

Adapters is cautioned because it can allow the product to be plugged with a detachable power cord.

Use only the type provided with your product or by your local distributor and/or retailer. If you are

unsure of the correct operational voltage, please contact your local distributor and/or retailer.

AMPLIFIER REQUIREMENTS

Due to the high output levels these speakers are capable of reproducing, exercise caution with the

volume control. Excessive volume over long periods of time can permanently damage your hearing.

Overdriving your ampliﬁer could also damage your SubWoofer.

CARE AND CLEANING

Your speakers have a durable ﬁnish that should only require dry dusting. Avoid use of abrasive or

solvent-based cleaners and harsh detergents. The brush attachment of your vacuum or a damp cloth

should remove any dust from your speaker grilles.

User Guide SubWoofer

3

IMPORTANT SAFETY INSTRUCTIONS

1. Read these instructions – All the safety and operating instructions should be read before

this product is operated.

2. Keep these instructions – The safety and operating instructions should be retained for

future reference.

3. Heed all warnings – All warnings on the appliance and in the operating instructions

should be adhered to.

4. Follow all instructions – All operating and use instructions should be followed.

5. Do not use this apparatus near water – The appliance should not be used near water

or moisture – for example, in a wet basement or near a swimming pool, and the like.

6. Clean only with dry cloth.

7. Do not block any ventilation openings. Install in accordance with the manufacture’s

instructions.

8. Do not install near any heat sources such as radiators, heat registers, stoves, or other

apparatus (including amplifiers) that produce heat.

9. Do not defeat the safety purpose of the polarized or grounding plug.

10. Protect the power cord from being walked on or pinched particularly at the plugs,

convenience receptacles, and at the point where they exit from the apparatus.

11. Only use attachments/accessories specified by the manufacturer.

12. Unplug the apparatus during lightning storms or when unused for long periods of time.

13. Refer all servicing to qualified personnel. Servicing is required when the apparatus

has been damaged in any way, such as power supply cord or plug is damaged, liquid has

been spilled or objects have fallen into the apparatus has been exposed to rain or moisture,

does not operate normally, or has been dropped.

14. WARNING - to reduce the risk of fire or electric shock, do not expose this apparatus

to rain or moisture. The apparatus shall not be exposed to dripping or splashing and

objects filled with liquids, such as vases, shall not be placed on the apparatus.

15. WARNING: The mains plug/appliance coupler is used as disconnect device, the

disconnect device shall remain readily operable.

16. This equipment is a Class II or double insulated electrical appliance. It has been

designed in such a way that it does not require a safety connection to electrical earth.

4

Congratulations

Thank you for your purchase of the ebode SubWoofer!

Everything about this SubWoofer has been designed to

work perfectly with your ebode LightSpeaker

®

system; from

the small, inconspicuous shape to state-of-the-art wireless

technology, this subwoofer will virtually disappear in your room

while delivering rich, deep bass. Place it in a corner or behind

a couch, or favourite chair — plug in to the closest electrical

outlet. There are no wires to run and no special tuning

required. Just plug and play!

Use the second zone capability so that others in different

rooms can listen to a second music source at the same

time. Or switch between the sources to listen to the music

you like best in one room or all rooms. To learn more about

the capabilities of your ebode LightSpeaker system visit us at:

www.ebodeelectronics.eu.

5

Table of Contents

SubWoofer Overview............................................................................6

What is in this Box?................................................................................7

Installation Considerations................................................................8

Installation Instructions.......................................................................9

Specifications......................................................................15

Warranty...............................................................................................16

CE Declaration...................................................................................130

Technical Support Information...................................Back Cover

6

SubWoofer

Overview

This wireless SubWoofer is

intended to install in just a few

minutes. The system can use up

to 4 wireless SubWoofers (when

used with an

ebode

LightSpeaker

transmitter) to provide bass to

your entire living area.

Additionally, the system can be expanded by adding our

patented LightSpeakers

®

. These LightSpeakers install

in minutes and fit into table lamps, hanging lamps or

any standard E27 Edison socket. The LED light provides

“green” lighting and the speaker provides outstanding

sound throughout your home. The LightSpeakers are

available from your retailer or at

www.ebodeelectronics.eu.

The entire system provides even greater flexibility to you

as the owner since you can take it with you if you move.

It leaves no trace that the system was ever installed or

used.

What’s in this Box

7

NOTE: This SubWoofer can only be used with the ebode

wireless LightSpeaker transmitter. It cannot be used or

operated without the LightSpeaker transmitter.

What’s in this Box

Wireless SubWoofer

Owner’s Manual

Power Supply

Remote and transmitter also sold separately.

8

Installation Considerations

Your ebode Wireless SubWoofer can be placed in any

area or zone where you would like additional bass to your

existing LightSpeaker distributed audio system. The only

wiring required is to plug it into a standard electrical

outlet. This SubWoofer will perform perfectly adding

rich, deep bass from wherever it is placed in your room,

however, it will provide the most bass if it is placed in or

close to a room corner. Your

ebode

wireless SubWoofer

will operate up to 15 meter (in any direction) away from

your LightSpeaker transmitter.

Please take a few minutes to read this manual. Following

simple setup instructions, will ensure you get the most

from your LightSpeaker SubWoofer.

9

Installation Instructions

Step 1: Please read all safety instructions at the start of this

manual.

Step 2: Decide where you would like to add additional bass

to your LightSpeakers and note the zone in which those

LightSpeakers are located.

Step 3:

Attach the power cord to the back of your SubWoofer

and plug it into the nearest electrical outlet. Be certain the power

switch on the rear of your SubWoofer is set to the “OFF” position.

Step 4: Pairing your SubWoofer to the LightSpeaker System.

Pairing is the process of “teaching” your transmitter to

recognize your SubWoofer as part of the LightSpeaker system.

It’s essential and only takes a couple of minutes.

A) Determine which zone your SubWoofer will be placed into

(See “Setting Up Zones” in your LightSpeaker owner’s manual).

B) Set the zone switch on the back of your SubWoofer to either

Zone 1 or Zone 2 depending on which zone it is to be located in.

+

Low Pass Crossover

80 Hz 100 Hz 120 Hz

Phase Zone

0° 180° 1 2

Volume

10

C) On your LightSpeaker transmitter, find and press the

“PAIRING Button” located on the back of the transmitter. The

status lights on the front of the transmitter will begin to flash.

Note:

When these lights are flashing, your transmitter is in

pairing mode; and you have approximately 30 seconds to

complete the next two steps. If you are unable to complete these

steps, simply push the pairing button on the transmitter again.

D) Set the Power switch, located on the back panel of your

subwoofer, to “ON”. While the lights are still flashing on the

transmitter, push the “pairing button” on the back panel of your

ebode

Wireless SubWoofer. When the “STATUS” LED turns

from Red to Green the pairing is complete.

+

F

ORMS TO

T

D. 1993

IFIED TO

Volume

Pairing

Status

+

Volume

Pairing

Status

11

Step 5: Setting the Phase Switch.

This will ensure that your ebode SubWoofer sounds it’s very

best in your favourite listening position. It is easiest to do with

two people: One at the listening position and the other at the

SubWoofer.

A) Your ebode Wireless SubWoofer is set up and ready to play.

Play a favourite piece of music, ideally one with a lot of bass to

ensure it’s functioning properly.

B) With one person at the listening position or some convenient

position not too close to the subwoofer (2 to 3 meter back is

fine) and the other person operating the phase, switch on the

back of the SubWoofer.

+

Low Pass Crossover

80 Hz 100 Hz 120 Hz

Phase Zone

0° 180° 1 2

12

C) While listening to the deepest bass notes in the music, flip

the phase switch back and forth while the listener determines

which setting produces the most bass. Leave the switch in the

position with the most bass.

D) Keep in mind there is no wrong position for this switch, and

if you can’t reliably hear a difference in either position then it will

not matter which position the switch is left at.

Step 6: Setting the Crossover Frequency.

There are three possible crossover frequencies to choose

from: 80Hz, 100Hz and 120Hz. The one you choose will

depend on where your SubWoofer is located and your personal

taste. Remember, if you find one setting you like better than

another, then leave it at the setting you like best. The closer

your ebode Wireless SubWoofer is to the corner, the LOWER

the crossover will be set. There is a lot of variability in rooms so

choose the crossover frequency that sounds right to you. If you

cannot hear a difference then the frequency you choose will not

make any difference.

Low Pass Crossover

80 Hz 100 Hz 120 Hz

Phase Zone

0° 180° 1 2

Volume

Pairing

Status

+

13

A) As in the case with the phase switch this step is easier to

perform with two people. Sit or stand in your preferred listening

position while another person pushes the button immediately

below the LEDs that mark the three different crossover

frequencies. Each time the button is pushed the crossover will

cycle to the next frequency first 80Hz (LED will light up), then

100Hz, and finally 120Hz. The next push of the button will light

the 80Hz frequency again.

B) Choose the setting that sounds the best and leave the

crossover set to this frequency. This can be changed at any

time in the future and will not affect the operation of either your

SubWoofer or your LightSpeaker system.

Step 7: Setting the volume control.

Your ebode Wireless SubWoofer has a built in volume control

so it can be matched to different numbers of LightSpeakers.

The more LightSpeakers in the listening area, the higher the

volume should be set.

+

Low Pass Crossover

80 Hz 100 Hz 120 Hz

Phase Zone

0° 180° 1 2

Volume

Pairing

Status

14

A) While listening to your LightSpeakers, cycle the volume

control up and down, stopping at the point where it sounds best.

You may want to test this with several types of music to find the

setting that sounds best to you.

B) When the volume reaches the maximum available, the

pairing LED will begin to flash.

Your ebode

Wireless SubWoofer is now ready to use!

+

Volume

Pairing

Status

15

SubWoofer Specifications:

Driver

• 6.5” diameter, microcellulose fiber cone body with natural

rubber surround

Voice Coil Diameter

• 25.4 mm (1.0”)

Enclosure

• Type - Ported; Front-firing driver with Rear-firing port

• Material - Medium Density Fiberboard

• Finish - Matte black, with black cloth grill

Amplifier

• Type - Digital

• Power - 65 W average sine power

• Features

0-180 degree phase switch

Three position variable low pass filter:

Settings at 80 Hz, 100 Hz, 120 Hz

Digitial volume control gain profile precisely matches

subwoofer SPL to LightSpeaker satellite SPL

at all volume settings

Frequency Response (-3 dB)

• 43 Hz - 120 Hz

Max SPL

• 102 dB - Output will match up to four LightSpeakers

Transmitter

• Frequency 2.4 Ghz proprietary

• Range - up to 15 meter from the transmitter

• AC Input - 120 Vac - 230 Vac

RF Remote Range - Up to 30 meter

Dimensions

• Enclosure - 22,9 cm (9.0”) H x 22,9 cm (9.0”) W x 30,5 cm

(12.0”) D + 1.6 cm (0.625”) for feet

16

Warranty - Home and Commercial Audio

Limited Liability

ebode electronics warrants its loudspeaker products to the original

purchaser to be free of manufacturing defects in material and workmanship

for a period of two years from date of purchase. This warranty is subject to

the following additional conditions and limitations.

The warranty is void and inapplicable if ebode electronics deems that the

product has been used or handled other than in accordance with the

instructions provided by the manufacturer, including but not limited to

damage caused by accident, mishandling, improper installation, abuse,

negligence, or normal wear and tear, or any defect caused by repair to the

product by anyone other than ebode electronics.

To obtain warranty service, please visit your dealer. A factory return

authorization number will be sent to you. Do not return any unit without first

receiving written authorization and shipping instructions from your dealer.

There are no other warranties, including without limitation, either express or

implied warranties of merchantability or fitness for a particular purpose, with

respect to the product.

Repair or replacement as provided under this warranty is the exclusive

remedy of the consumer/purchaser. ebode electronics shall not be

responsible for any incidental or consequential damages except to the extent

provided (or prohibited) by applicable law.

Some COUNTRIES do not allow the exclusion or limitation of incidental or

consequential damages, so the above limitation may not apply to you.

This warranty gives you specific legal rights, and you may also have other

rights which vary from COUNTRY TO COUNTRY.

17

Questions? Contact your local dealer!

Have a question about your ebode electronics speakers? Talk to the

people who know them best! We’re waiting to hear from you!

WRITE THE PART NUMBER AND SERIAL NUMBER FROM YOUR

PRODUCT BOX HERE AND RETAIN FOR PRODUCT REGISTRATION

Part Number:______________________________________________

Serial Number:_____________________________________________

18

Der Blitz im gleichseitigen Dreieck weist auf gefährliche Hochspannung im Gerät hin, die

zu Stromschlag führen kann.

Das Ausrufungszeichen im gleichseitigen Dreieck weist auf wichtige Bedienungs- und

Wartungsanleitungen hin.

WARNUNG: Zur Vermeidung von Feuer und Stromschlag setzen Sie das Gerät bitte nicht Regen oder

Feuchtigkeit aus.

WARNUNG Stellen Sie keine offenen Flammen (wie brennende Kerzen) auf dem Gerät ab.

WARNUNG – Gerätegehäuse nicht öffnen! Stromschlaggefahr. Die Hochspannung in diesem Gerät ist

lebensgefährlich. Es beﬁnden sich keine vom Verbraucher wartbaren Teile im Gerät. Wenden Sie sich

mit Wartungs- und Reparaturarbeiten stets an einen autorisierten Kundendienst.

Stellen Sie das Gerät in unmittelbarer Nähe einer Steckdose auf und achten Sie darauf, dass der

Hauptschalter jederzeit gut erreichbar ist.

WARNUNG: Dieses Gerät darf NUR mit der Netzspannung betrieben werden, wie auf der

Geräterückseite oder dem mitgelieferten Netzteil aufgedruckt. Andere Netzspannungen können

zu nicht reparablen Schäden führen und sind nicht von der Garantie abgedeckt. Wir warnen vor

der Benutzung eines Steckeradapters, da hierüber das Gerät an einer ungeeigneten Spannung

angeschlossen werden kann. Benutzen Sie nur das mitgelieferte Netzkabel. Ist Ihnen Ihre

Netzspannung nicht bekannt, so wenden Sie sich bitte an Ihren örtlichen Stromversorger oder an

Ihren Fachhändler.

ANFORDERUNGEN VERSTÄRKER

Aufgrund ihres hohen Ausgangspegels sind diese Lautsprecher in der Lage, sehr laute Geräusche

wiederzugeben, seien Sie mit der Lautstärkeeinstellung vorsichtig. Übermäßige Lautstärke über

einen längeren Zeitraum Übermäßige Lautstärke über einen längeren Zeitraum kann zu dauerhaften

Hörschäden führen. Die Übersteuerung Ihres Verstärkers kann ebenfalls zu einer Beschädigung der

SubWoofer führen.

REINIGUNG UND PFLEGE

Ihre Lautsprecher haben ein haltbares Finish, das nur abgestaubt werden muss. Benutzen Sie keine

scheuernden, aggressiven oder lösungsmittelhaltigen Reinigungsmittel. Der Bürstenaufsatz Ihres

Staubsaugers oder ein feuchtes Tuch sind zum Abstauben des Grillgitters völlig ausreichend.

Bedienungsanleitung SubWoofer

19

WICHTIGE SICHERHEITSHINWEISE

1. Lesen Sie unbedingt die mitgelieferten Sicherheits- und Bedienungsanleitungen vor der

Inbetriebnahme des Geräts.

2. Bewahren Sie die Sicherheits- und Bedienungsanleitungen für künftiges Nachschlagen auf.

3. Beachten Sie alle Warnhinweise auf dem Gerät und in der Bedienungsanleitung.

4. Bitte benutzen Sie das Gerät ausschließlich wie in den Sicherheits- und

Bedienungsanleitungen beschrieben.

5. Benutzen Sie das Gerät nicht in unmittelbarer Nähe von Wasser oder Feuchtigkeit,

beispielsweise in einem feuchten Kellergeschoss oder in der Nähe eines Schwimmbeckens

und dergleichen.

6. Reinigen Sie das Gerät nur mit einem trockenen Tuch.

7. Blockieren Sie nicht die Lüftungsöffnungen. Installieren Sie das Gerät entsprechend der

Herstellerangaben.

8. Installieren Sie das Gerät nicht in unmittelbarer Nähe von Wärmequellen wie Heizungen,

Heizkörpern, Herden oder sonstigen Wärme erzeugenden Geräten (wie Verstärker).

9. Schützen Sie das Netzkabel, damit es nicht belastet oder eingeklemmt wird, insbesondere

am Stecker und dem Ausgang am Gerät.

10. Benutzen Sie nur vom Hersteller spezifizierte Zubehörteile.

11. Bei Gewitter oder längerer Nichtbenutzung ziehen Sie bitte den Netzstecker.

12. Wenden Sie sich mit Reparaturen stets an einen autorisierten Kundendienst. Eine

Wartung ist nötig, wenn das Gerät, der Stecker oder das Netzkabel beschädigt sind,

wenn Feuchtigkeit oder Fremdkörper in das Gerät eingedrungen sind oder es Regen oder

Feuchtigkeit ausgesetzt war, wenn es nicht wie gewöhnlich funktioniert oder fallen gelassen

wurde.

13. WARNUNG – Zur Vermeidung von Feuer und Stromschlag setzen Sie das Gerät nicht

Regen oder Feuchtigkeit aus. Schützen Sie das Gerät vor Spritzwasser und Tropfwasser und

stellen Sie keine mit Wasser gefüllten Gegenstände (wie Vasen) auf dem Gerät ab.

14. WARNUNG: Der Netzstecker dient dem vollständigen Abtrennen des Geräts vom

Stromnetz und muss jederzeit frei zugänglich sein.

15. Dieses Gerät ist ein Klasse II oder doppelt isoliertes Elektrogerät. Es ist konzipiert, nicht

geerdet werden zu müssen.

16. Dieses Gerät ist ein Klasse II oder doppelt isoliertes Elektrogerät. Es ist konzipiert, nicht

geerdet werden zu müssen. (THIS IS CONFLICTING WITH 9)

20

Herzlichen Glückwunsch

Vielen Dank, dass Sie sich für den ebode SubWoofer

entschieden haben. Dieser SubWoofer wurde konzipiert,

um einwandfrei mit Ihrem ebode LightSpeaker® System

zu arbeiten, von der kleinen, unauffälligen Form bis zur

modernsten Drahtlostechnologie. Dieser SubWoofer passt

sich völlig an Ihren Raum an und liefert gleichzeitig reiche,

tiefe Bässe. Zur Installation werden keine Kabel oder

Einstellungen benötigt. Stellen Sie den SubWoofer in einer

Ecke oder hinter Ihrem Lieblingssessel auf und schließen Sie

ihn an der nächsten Steckdose an. Einfach anschließen und

benutzen.

Benutzen Sie die Einstellmöglichkeit für die zweite Zone, um

in einem zweiten Raum gleichzeitig eine andere Musikquelle

wiederzugeben. Oder schalten Sie zwischen den Quellen um,

um Ihre Lieblingsmusik in einem oder allen Räumen zu hören.

Für weitere Informationen zu den Fähigkeiten Ihres ebode

LightSpeaker Systems besuchen Sie uns im Internet bei:

www.ebodeelectronics.eu.

La page charge ...

EDOBE XDOM SUBWOOFER Le manuel du propriétaire

Ce manuel convient également à

EDOBE XDOM SUBWOOFER Le manuel du propriétaire

dans d''autres langues

Documents connexes

Autres documents