Genie 4042 Manuel utilisateur

SILENTMAX

®

1200

Model 4042

GARAGE DOOR OPENER

Genie, Genie logo, Intellicode, Safe-T-Beam & SilentMax

are registered trademarks of GMI Holdings, Inc., dba The Genie Company.

Homelink is a registered trademark of Johnson Controls Technology Company. Car2U is a registered trademark of Lear Corporation. © The Genie Company 2011 PN# 37309500118, 04/2011

OPERATION AND MAINTENANCE MANUAL

Includes INTELLICODE

®

2 Remote Control. Safe-T-Beam

®

System must be installed to close door.

Homelink

®

and Car2U

®

compatible.

For Answers and Assistance:

1.800.354.3643

or visit www.geniecompany.com

WARNING: To reduce the risk of injury to persons or damage to property, use this opener only with a

one-piece or sectional residential door up to 7 ft in height. Extension kit is available for 8 ft. one-piece

or sectional residential doors.

SAVE THIS MANUAL FOR FUTURE REFERENCE.

INSTALLER: LEAVE THIS MANUAL WITH HOMEOWNER.

2

SAFETY INFORMATION

IMPORTANT SAFETY INSTRUCTIONS

READ AND FOLLOW ALL INSTRUCTIONS

SAVE THESE INSTRUCTIONS

CONVENTIONS USED IN THESE INSTRUCTIONS

Garage doors are large, heavy objects that move with the help of springs under high tension and electric motors. Since moving

objects, springs under tension, and electric motors can cause injuries, your safety and the safety of others depend on you reading

the information in this manual. If you have questions or do not understand the information presented, call your nearest trained

door system technician or visit our website.

The following Safety Alert symbol and signal words are used throughout this manual to call attention to and identify different

levels of hazard and special instructions.

This is the safety alert symbol. This symbol alerts you to potential hazards that can kill or hurt you and others.

All safety messages will follow the safety alert symbol and the word "DANGER", "WARNING", or "CAUTION"

DANGER indicates an imminently hazardous situation which, if NOT avoided, will result in death or serious injury.

WARNING indicates a potentially hazardous situation which, if NOT avoided, could result in death or serious injury.

CAUTION indicates a potentially hazardous situation which, if NOT avoided, may result in injury or property damage.

The word NOTE is used to indicate important steps to be followed or important considerations.

noitneverPtceffEdrazaH laitnetoP

WARNING

Could result in

Death or Serious

Injury

Keep people clear of opening while Door is moving.

Do NOT allow children to play with the Door Opener.

Do NOT operate a Door that jams or one that has a broken

spring.

WARNING

Could result in

Death or Serious

Injury

Turn OFF power before removing opener cover.

When replacing cover, make sure wires are NOT pinched or

near moving parts.

Opener must be fully grounded.

WARNING

Could result in

Death or Serious

Injury

Do NOT try to remove, install, repair or adjust springs or

anything to which door spring parts are fastened, such as,

wood blocks, steel brackets, cables or other like items.

Installations, repairs and adjustments must be done by

a trained door system technician using proper tools and

instructions.

OVERVIEW OF POTENTIAL HAZARDS

READ THIS SAFETY INFORMATION

SAFETY FEATURES

Safe-T-Beam® (STB) Non-Contact Reversing System

Puts an invisible beam across the door opening. The door stops and reverses to the full open position if anything

passes through the beam. LED indicator lights on the powerhead and on the STBs provide a self diagnostic code

if an operational problem exists.

Safe-T-Reverse® Contact Reversing System

Automatically stops and reverses a closing door within two seconds of contact with an object.

Automatic ForceGuard™ Control

Automatically sets the force required to fully open and close the door for maximum safety.

Watch Dog™ Monitoring System

Monitors the Safe-T-Beam® system to ensure proper functionality and will automatically stop and reverse a

closing door if a problem is detected.

Manual Emergency Release

Manually releases door from door opener. Used during a power failure or other emergency to allow manual

opening and closing of door.

SmartSet™ Electronic Programming

Easily adjust the programming to reduce opening speed to a desired rate, vary limits and force, and program new

remotes.

Automatic Lighting System

Two bulb lighting system supplies up to 200 Watts of light for safer evening exits and entries. Turns ON when

door is activated and automatically turns OFF 4 minutes later.

Integrated Motion Detection (Not available on all models)

Select units have motion detection built into the powerhead. Lights automatically turn ON when motion is

detected for much safer movement through the garage. Lights will turn OFF after 4 minutes of no motion.

3

INTELLICODE® 2 Access Security System

A new generation superior encryption system that enhances the security of the door opener by continuously

changing the access code each time the remote is used. The door opener responds to each new code only once.

An access code copied from a working system and tried again will not control the door opener.

OPENER FEATURES

Wall Console, Series III

Operates door opener from inside garage. The Wall Console has an Indicator Light with: Open/Close, Sure-Lock™,

and Independent Light Control buttons.

and Car2U® compatible. Refer to the programming instructions on page 10 and then

follow the HomeLink® or Car2U® instructions in your car owner’s manual.

TABLE OF CONTENTS

Section ....................................................................................Page

Safety Information .................................................................................................... 2

Opener Features & Safety Features ................................................................... 3

Table of Contents ....................................................................................................... 4

Installation

Important Installation Instructions ........................................................5

1 Programming Limits & Force .............................................................6-7

Contact Reverse Test ........................................................................................... 8

2 Program IntelliCode® 2 Remote to Powerhead ............................9

Programming HomeLink®, Car2U®, IntelliCode® 1 remotes or wireless

keypads ................................................................................................................10

Reference

3 Typical Installed Illustrations ................................................................ 11-13

Powerhead & Rail Assembled View ............................................................11

Typical Sectional Door Installation ............................................................12

Typical One Piece Door Installation ...........................................................13

4 Overview of Powerhead Controls ..............................................................14

5 Overview of Remotes and Options ...................................................... 15-16

Lost or Stolen Remote - Clearing Memory ..................................................15

IntelliCode® Features ........................................................................................16

Previously Installed Openers ..........................................................................16

6 Maintenance & Troubleshooting ......................................................... 17-26

Important Safety Instructions ........................................................................17

Routine Monthly Maintenance .....................................................................18

Door Balance (Spring Tension) ......................................................................18

Safe-T-Beam® System Check ..........................................................................18

Contact Reverse Test .........................................................................................18

Change Light Bulbs ...........................................................................................19

Motion Detector - Overview ...........................................................................19

Reset - Open/Close Travel Limit .....................................................................19

Carriage Engage/Disengage ..........................................................................19

Wall Console - Overview ..................................................................................20

Optional Dual Wall Console - Installation

.................................................20

Remote Battery Replacement ........................................................................21

Speed Adjustment Guide .................................................................................22

Force Adjustment Guide ..................................................................................23

Troubleshooting Guide - Operation ..................................................... 24-25

Troubleshooting Guide - Powerhead LEDs ................................................25

Reference - Wiring Diagram ..........................................................................26

Warranty ......................................................................................................................27

4

OPENER MUST BE INSTALLED WITH THE INCLUDED

WALL CONSOLE.

Safe-T-Beam® SAFETY REVERSE SYSTEM MUST BE

INSTALLED TO CLOSE DOOR.

Begin here after the opener's physical assembly

and installation has been completed.

There are no assembly or installation steps included in this manual. Contact

your Genie® Professional Dealer for an installation poster, if required, or visit

www.geniecompany.com to download a PDF file.

The following mechanical assembly tasks must be completed before continuing.

 Powerhead and rail are bolted to each other (An illustration is shown on page 11)

Example illustrations of the following items are shown on pages 12 and 13

 Rail end is attached to a header bracket which is attached to the garage door header

 Powerhead is attached to a support frame suspended from the ceiling or ceiling joists

 Both pieces of door arms are assembled and are attached to the garage door

 Safe-T-Beam® sensors installed and wired

 Wall console installed and wired (Shown on page 20)

 Carriage is engaged to the chain or belt drive (An illustration is shown on page 11)

 Powerhead is plugged into an approved power outlet

Begin programming by setting Limits (see next page.)

5

IMPORTANT INSTALLATION INSTRUCTIONS

WARNING: To reduce the risk of severe injury or death:

1. READ AND FOLLOW ALL SAFETY, INSTALLATION

AND OPERATION INSTRUCTIONS. (If you have

questions or do not understand an instruction, call

The Genie Company.)

2. Install only on a properly balanced sectional or

one piece garage door. An improperly balanced

door could cause severe injury. Have a trained door

system technician make repairs or adjustments to

cables, spring assemblies, and other hardware before

installing the opener.

3. Remove all ropes and remove or make inoperative all

locks connected to the garage door before installing

opener.

4. Where possible, install the door opener 7 feet or

more above the floor. For products having an

emergency release, mount the emergency release

within reach but, at least 6 feet above the floor to avoid

contact with vehicles to prevent accidental release.

5. Do NOT connect the opener to source of power until

instructed to do so.

6.

Locate the wall console:

• Within sight of the garage door,

• At minimum height of 5 feet so small children

are not able to reach it, and

• Away from all moving parts of the door.

7. Install the Entrapment WARNING Label next to the

wall console in a prominent location.

8. After installing the opener, the door must reverse

within 2 seconds when it contacts a 1-1/2 inch high

object (or a 2 x 4 board laid flat) on the floor.

INFRARED PROTECTION FUNCTION

1. When garage door is opening, its movement will not be influenced if the Safe-T-Beam® is

obstructed.

2. If the Safe-T-Beam® is obstructed before the garage door fully closes, the door will not close.

3. When the garage door is closing, if Safe-T-Beam® is interrupted by person or obstacle, the garage

door will stop its downward travel and reverse automatically to its fully opened position.

4.

Remove Safe-T-Beam® obstruction.

5. If the Safe-T-Beam® System fails, loses power, or is installed improperly, press and hold the wall

console "open/close" button until the door reaches its fully closed position. If you release the

"open/close" button on the wall console during the closing movement the door will reverse

automatically to its fully opened position.

A PDF VERSION INSTALLATION POSTER IS AVAILABLE AT WWW.GENIECOMPANY.COM

OR CALL 1-800-35-GENIE TO OBTAIN AN EMAIL PDF FILE

WARNING

• Make sure doorway is in view and clear of obstacles

and people to avoid injury or damage to property.

• DO NOT operate this unit from wall console before

LIMITS and FORCE are set. Severe damage to the

opener can occur.

• The bullet MUST be engaged to carriage BEFORE

setting limits. See Installation Poster (if provided) or

refer to pages 11 and 19.

NOTE: If bullet has NOT been engaged to

the carriage, do so now.

6

PROGRAM

SET

—

+

SETTING & TESTING LIMITS AND FORCE

The OPEN (UP) and CLOSE (DOWN) Door Limit positions are controlled by making

adjustments using the panel located on the bottom of the powerhead. Begin with

Step 1 and continue through Step 10. Door Force is set during the final Open/Close

cycle of these steps. The powerhead will automatically set door speed at slow if the

distance between limits is less than 6 feet. Once Limits and Force are set DO NOT use

the

or buttons to open or close door.

A) CLOSE DOOR TRAVEL LIMIT

NOTE: You can start and stop door

movement using either

buttons until

door is in correct open or closed position.

Watch door move

PROGRAMMING LIMITS & FORCE

(Continuing from Installation Poster if provided)

1

G

RAM

SE

—

+

5

PROGRAM

SET

—

+

PRESS and HOLD

SEE BOTH

Blue LEDs

come ON

SEE round

Blue LED

come ON

SEE round Blue

LED flashing

RELEASE

1

2 3

4

NOTE: If one or both LEDs come ON RED

at this time, Limits programming menu

was not entered properly. You must exit

programming and restart.

To exit the programming function wait 30

seconds for the programming to time out.

PRESS and RELEASE

Please note that there is a 30 second timeout

between each programming step.

A programming timeout during these steps has

occured when two RED flashing LEDs appear.

In the event of a timeout please restart at Step 1.

OT CE

O

R

CO

S

R

T

D

P

O

W

O

DE

PROGRAM

SET

—

PRESS and

RELEASE

SEE long Blue

LED come ON

If RED LED comes ON - STOP and

exit programming.

PRESS and HOLD until door is FULLY CLOSED then RELEASE

7

PR

OGRAM

SET

—

SEE long Blue LED

flashing

6

Watch door move

RA

M

SET

—

+

B) OPEN DOOR TRAVEL LIMIT

OT E

O

R

E

O

OS R

E

D

P

O

W

O

D

E

DOOR CLOSES

DOOR OPENS

Door Limits are set.

Both LEDs flash Blue

and go OFF.

Continue with

Step 9 SET FORCE.

SET FORCE Force is set automatically with first full

CLOSE/OPEN door operation.

7 8

9

10

Perform a successful CONTACT REVERSE TEST and

then continue with remote programming.

NOTE: To reset LIMIT settings, repeat Steps 1-10.

PRESS and

RELEASE

On Wall Console

PRESS and RELEASE

PR

OGRAM

SET

—

NOTE: You can start and stop door

movement using either

buttons until

door is in correct open or closed position.

PRESS and

RELEASE

On Wall Console

PRESS and RELEASE

PRESS and HOLD until door is FULLY OPEN then RELEASE

8

1

2

3

4

CONTACT REVERSE TEST

The Force and Limit settings on the previous page MUST be COMPLETED before Contact

Reverse testing.

1. Test.

• Open garage door using wall console.

– Place a 2" x 4" board (laid flat) under center of garage door opening.

• Close garage door using wall console.

• When door contacts board, the door must stop (within 2 seconds) and reverse

direction returning to open position.

2. Adjustment.

• If the door:

– Stops before it contacts the 2 x 4 board, it may simply be responding to an

improperly set down limit. Return to pages 6-7 and repeat steps 1 through 10

to correct down limit.

– Stops after contacting the 2 x 4 board and does not reverse it may need an

adjustment to the down limit. Return to pages 6-7 and repeat steps 1 through 10

to correct down limit.

• Test again. Repeat as necessary until door reverses upon contacting board.

WARNING

A moving door can cause serious injury or death.

1. Keep people clear of opening while door is moving.

2. Do NOT allow children to play with opener, including

wall console, remote, or wireless keypad.

3. During programming, door opener could begin to run,

so stay away from moving door and its parts.

On Wall Console

PRESS and RELEASE

DOOR OPENS

PRESS and RELEASE

Once the Contact Reverse Testing is complete continue with Programming Remotes on the next page.

9

PROGRAM

SET

—

+

PROGRAM

SET

—

+

PROGRAM INTELLICODE® 2 REMOTE TO POWERHEAD FOR HELP-1-800-35-GENIE OR WWW.GENIECOMPANY.COM

2

PRESS and HOLD

SEE BOTH

Blue LEDs

come ON

SEE round Blue

LED come ON

SEE long Purple

LED flashing

RELEASE

1 2 3 4

5

6 7

The next press of the remote will operate door.

Repeat as necessary for other remotes.

Bring remote(s) to powerhead location.

Begin with Step 1 and continue through Step 7 for each button to be programmed.

NOTE: The following instructions are for the remote(s) provided with this opener. This

remote is preset for use with the IntelliCode® 2 Access Security System. Refer to page

16 for additional information on IntelliCode® 1 and 2 remotes and how to switch from

IntelliCode® 2 to IntelliCode® 1. See page 10 for programming instructions using

IntelliCode® 1 remotes.

PRESS and

RELEASE

PRESS and

RELEASE

PRESS and

RELEASE

Basic powerhead programming is complete.

Your garage door opener is ready to use.

WARNING

A moving door can cause serious injury or death.

1. Keep people clear of opening while door is moving.

2. Do NOT allow children to play with opener, including

wall console, remote, or wireless keypad.

3. During programming, door opener could begin to run,

so stay away from moving door and its parts.

SEE both LEDs OFF

SEE both LEDs

flash Blue

PRESS and

RELEASE

SEE both LEDs

flash Purple

10

PROGRAM

SET

—

+

PROGRAM

SET

—

+

PRESS and HOLD

SEE BOTH

Blue LEDs

come ON

SEE one

Blue LED

come ON

PRESS and release a previously programmed

Genie® IntelliCode® 2 remote button on

remote. If you are unsure which remote you

have see page 16. Remote must be IntelliCode®

2 enabled.

RELEASE

1

2

3

4

OPTIONAL

PROGRAMMING POWERHEAD TO

Homelink®, Car2U®, or IntelliCode® 1 REMOTES and IntelliCode® 1 WIRELESS KEYPADS

To complete any of these tasks you MUST have at least one Genie® IntelliCode® 2 remote

button already programmed to the powerhead present.

For Homelink® or Car2U®: You must also have your Homelink® or Car2U® enabled vehicle

present and their programming instructions to perform these programming steps.

For Genie® IntelliCode® 1 remote: You must also have your Genie® IntelliCode® 1 remote

present.

For Genie® IntelliCode® 1 wireless keypad: You must also have your Genie® wireless

keypad installed and a PIN already programmed into the keypad. Programming instructions

for Genie® IntelliCode® 2 wireless keypad will come with the wireless keypad.

PRESS and

RELEASE

5

On the IntelliCode® 1 remote

PRESS a button and RELEASE. SEE

long LED come ON Purple.

6

IntelliCode® 1 remote or wireless keypad programming

7

On the IntelliCode® 1 remote

PRESS the same button and

RELEASE.

SEE both LEDs on the powerhead

come ON Blue. The next press of

the remote will operate door.

Test. Repeat as necessary for any

other IntelliCode® 1 remotes.

Genie® IntelliCode® 1 remote Genie® IntelliCode® 1 wireless keypad

SEE long Purple

LED flashing

SEE both LEDs

flash Purple

All optional programming is complete. Your garage door opener is ready to use.

5

For Car2U® enabled vehicles follow the Car2U®

instructions.

6

Test. Repeat as necessary for any other Car2U®

enabled vehicle.

Homelink® programming

If your Homelink® has been previously programmed to an

Genie®

opener begin with Step 1 and continue through Step

5 and 6 of the Homelink® section below.

If your Homelink® has not yet been linked to a Genie®

opener then go to page 16 and change one remote button

from IntelliCode® 2 to IntelliCode® 1, then program

that button with the car Homelink® using Homelink®

instructions and repeat steps 1-4 then continue with

Homelink® steps 5-6.

5

6

PRESS the Homelink® button twice.

Test. Repeat as necessary for any other pre-

programmed Homelink® enabled vehicle.

5

Enter your wireless keypad PIN.

6

Press and hold button 1 second

then release and see on powerhead

long LED come ON Purple.

7

Press and hold button 1

second again then release and see on

powerhead both LEDs flash Blue.

8

Press and hold button again and

opener will activate

9

Wait 30 seconds, enter pin and press

button to verify operation.

Homelink® or Car2U® programming

Release Handle

Poignée de déverrouillage

Palanca de liberación

POWER HEAD

TÊTE DE PUISSANCE

CABEZA DE LA ENERGÍA

Power Cord

Cordon de secteur

Cable eléctrico

Door Arm

Bras de la porte

Brazo de la puerta

Header Bracket

Embase support

Soporte del travesaño

Clevis Pin, Long

Axe de chape, longue

Pasador de grillete, largo

Clip

Étrier

Abrazadera

Engage belt bullet to Carriage Slide

Embrayez la courroie balle

à la coulisse du chariot

Enganche la correa bala al deslizamiento del carro

Door Arm

Bras de la porte

Brazo de la puerta

See BLUE bag for screws

Voir le sac BLEU pour des vis

Vea el bolso AZUL para los tornillos

Tensioner (located inside rail, pg 20)

Tendeur (situé à l'intérieur du rail, pg 20)

Tensor (ubicado dentro del riel, pg 20)

Belt (located inside rail)

Courroie

(qui se trouve à l'intérieur du rail)

Cadena o correa (ubicada dentro del riel)

Carriage Slide (located inside rail)

Coulisse du chariot (situé à l'intérieur du rail)

Deslizamiento del carro (ubicado dentro del riel o carril)

Bullet

Balle

Bala

RETAIL RAIL

RAIL DE DETAIL

RIEL DE VENTA AL MENUDEO

Rail Connector

Maillon de junction du rail

Conector del riel

PROFESSIONAL INSTALLER RAIL

RAIL PROFESSIONNEL D'INSTALLATEUR

CARRIL PROFESIONAL DEL INSTALADOR

Rail Connector

Maillon de junction du rail

Conector del riel

11

REFERENCE - POWERHEAD & RAIL ASSEMBLED VIEW

RÉFÉRENCE – VUE DE LA TÊTE D’ALIMENTATION & DU RAIL ASSEMBLÉ

REFERENCIA - VISTA DEL CABEZAL ELÉCTRICO Y RIEL ENSAMBLADOS

NOTE: Use wall console and safety sensors provided with this unit. Do NOT substitute wall console or safety sensors.

REMARQUE: Utilisez la console sur le mur et les capteurs de sécurité fournis avec cet appareil. NE PAS substituer la console du mur ou les capteurs de sécurité.

NOTA: Use la consola de pared y los sensores de seguridad proporcionados con esta unidad. NO sustituya la consola de pared ni los sensores de seguridad.

FIG. 3-3

12

NOTICE

O R

B

CO E

OS

R C ED

P

O

W

O

DE

TYPICAL SECTIONAL DOOR INSTALLATION MOC.YNAPMOCEINEG.WWW RO EINEG-53-008-1-PLEH ROF

INSTALLATION TYPIQUE SUR UNE PORTE SECTIONELLE .................................POUR OBTENIR DE L’AIDE-1-800-35-GENIE

INSTALACIÓN HABITUAL DE UNA PUERTA SECCIONAL ................................. PARA OBTENER AYUDA, LLAME AL 1-800-35-GENIE

SAFE-T-BEAM® SENSORS

PALPEURS de SAFE-T-BEAM®

SENSORES SAFE-T-BEAM®

OPTIONAL - HEADER BRACKET MOUNTING

BOARD

PLANCHE DE MONTAGE FACULTATIVE POUR SUP-

PORT D’EMBASE

TABLERO DE MONTAJE OPCIONAL DE SOPORTE DEL

UMBRAL

BRACING

ATTACHE

ARRIOSTRAMIENTO

POWER CORD* TO 120V

GROUNDED OUTLET

CÂBLE D’ALIMENTATION** À PRISE

DE CONTACT DE 120V À CONTACT

DE MISE À LA TERRE

CABLE DE ALIMENTACIÓN*** A

UN TOMACORRIENTE DE 120 V

CONECTADO A TIERRA

EXTENSION SPRING

RESSORT DE TRACTION

RESORTE DE EXTENSIÓN

TORSION SPRING

RESSORT DE TORSION

RESORTE DE TORSIÓN

OR / OU / O

TYPICAL SUPPORT BRACKET (NOT PROVIDED)

SUPPORT TYPIQUE (NON FOURNI)

ESCUADRA DE SOPORTE TÍPICA (NO SE INCLUYE)

*If required direct wiring of power supply to opener must be installed by a licensed electrician. Power cord must reach

grounded outlet without use of extension cord.

**Le câblage direct de l'alimentation d'énergie à l'ouvreur doit être installé s'il y a lieu par un électricien autorisé. Le cordon de

secteur doit atteindre la sortie au sol sans utilisation de corde de prolongation.

***Si es necesario, un electricista certificado debe instalar el cableado directo del suministro de energía al abre puertas. El cable eléctrico

debe llegar al enchufe con conexión a tierra sin utilizar un cable de extensión.

3

FIG. 3-1

BRAS DE LA PORTE

BRAZO DE LA PUERTA

NOTE: For Low Headroom

installations do NOT reduce door

arm lengths by cutting door arms.

To clear door, reposition door

arms with greater angle.

REMARQUE: Pour les installations

à basse hauteur, ne PAS réduire la

longueur du bras de la porte en

coupant les bras de la porte. Pour

dégager la porte, repositionnez les

bras de la porte à un plus grand

angle.

NOTA: Para instalaciones a alturas

bajas, NO reduzca las longitudes de

los brazos de la puerta cortándolos.

Para despejar la puerta, vuelva a

colocar los brazos de la puerta en otra

posición con un ángulo mayor.

MAX. 6" - MIN. 5"

6 po (15 cm) MAX. -

5 po (12,7 cm) MIN.

MAX. 6" - MIN. 5"

DOOR ARM

13

SECTIONAL DOOR

PORTE SECTIONELLE

PUERTA SECCIONAL

ONE PIECE DOOR

PORTE D’UNE PIÈCE

PUERTA DE UNA SOLA PIEZA

O

R

E

O

S

B

STR

T

ED

P

O

W O

D

E

LIFT SPRING

RESSORT DE LEVAGE

RESORTE DE ELEVACIÓN

*If required direct wiring of power supply to opener must be installed by a licensed electrician. Power cord must reach

grounded outlet without use of extension cord.

**Le câblage direct de l'alimentation d'énergie à l'ouvreur doit être installé s'il y a lieu par un électricien autorisé. Le cordon de

secteur doit atteindre la sortie au sol sans utilisation de corde de prolongation.

***Si es necesario, un electricista certificado debe instalar el cableado directo del suministro de energía al abre puertas. El cable eléctrico

debe llegar al enchufe con conexión a tierra sin utilizar un cable de extensión.

TYPICAL ONE PIECE DOOR INSTALLATION ........... FOR HELP-1-800-35-GENIE OR WWW.GENIECOMPANY.COM

INSTALLATION TYPIQUE D’UNE PORTE DE GARAGE D’UNE PIÈCE .............POUR OBTENIR DE L’AIDE-1-800-35-GENIE

INSTALACIÓN HABITUAL DE PUERTA DE UNA SOLA PIEZA ................................... PARA OBTENER AYUDA, LLAME AL 1-800-35-GENIE

FIG. 3-2

WARNING

To reduce the risk of injury to persons or damage to property -

Use this opener only with a one piece or sectional door.

AVERTISSEMENT

Pour diminuer le risque de blessures corporelles ou

d’endommagement matériel - Utiliser cet l’ouvreur uniquement

avec les portes à section.

ADVERTENCIA

Para reducir el riesgo de lesión a las personas o daños a la propiedad

- utilice este abre puertas solamente con una puerta de una pieza o

seccional.

SAFE-T-BEAM® SENSORS

PALPEURS de SAFE-T-BEAM®

SENSORES SAFE-T-BEAM®

POWER CORD* TO 120V

GROUNDED OUTLET

CÂBLE D’ALIMENTATION**

À PRISE DE CONTACT DE

120V À CONTACT DE MISE

À LA TERRE

CABLE DE ALIMENTACIÓN***

A UN TOMACORRIENTE DE

120 V CONECTADO A TIERRA

HEADER BRACKET MOUNTING BOARD (not provided)

PLANCHE DE MONTAGE FACULTATIVE POUR SUPPORT

D’EMBASE (non fourni)

TABLERO DE MONTAJE DE SOPORTE DEL UMBRAL

(no se proporciona)

TYPICAL SUPPORT BRACKET (NOT PROVIDED)

SUPPORT TYPIQUE (NON FOURNI)

ESCUADRA DE SOPORTE TÍPICA (NO SE INCLUYE)

14

SET

PROGRAM

Open

Travel

Button

ROUND

LED Indicator

(Light)

Facing

Garage Door

LONG

LED Indicator

(Light)

Close

Travel

Button

OVERVIEW OF POWERHEAD CONTROLS

This section describes the simple programming

functions. Use this page to familiarize yourself with the

buttons and LED indicators used to program the opener.

NOTE: These and buttons are for programming use

only. Do NOT use these buttons to operate the opener.

PROGRAM

SET

—

+

To garage door

FIG. 4-1 Locate programming buttons

FIG. 4-2 Programming buttons

There are three programming buttons and two lights

(LEDs) on the powerhead.

Each of the buttons are used to enter and complete

the setup programming. The LEDs indicate status or a

function change by illuminating ON, OFF, or ON flashing

in one of three different colors: BLUE, RED, or PURPLE.

Throughout the instructions in this manual the buttons

and LEDs are also displayed as icons.

Buttons

Name Shape Use

Program button

PRO G RA M

SET

Enters into and selects

programming menus

Close Travel button

multi-function;

moves door, advances

through menus

Open Travel button

multi-function;

moves door, advances

through menus

LED Colors

Round Red and Long Red

Round Purple

and Long Purple

Round Blue

and Long Blue

Programming Overview

There are four Powerhead program menus:

Remote Program (Default menu)

Limits Program

Speed Program*

Force Program*

Programming steps for Limits and remotes are found on

pages 6 through 10.

*Force and Speed settings are set at the factory and do

not normally require adjustment programming. Custom

programming instructions for Speed and Force are

located in the Troubleshooting Section of this manual.

These are the basic steps to enter into the four

programming menus:

1. Press

PR O G R A M

SET

and hold until both BLUE lights come ON

then release.

2. Both LEDs go out and Round BLUE light comes

ON. You are in the Program Menus at the Remote

Programming.

By using the

or the button you can navigate to

the Limits, Speed, or Force program menus and the

LED display will change accordingly.

Each program menu has a specific LED display.

Press Program LED Display

Default Remote Round Blue

Limits Long Blue

X2 Speed Round Blue & Long Blue

X3 Force Round Red

3. Press

PR O G R A M

SET

button to enter into the program menu

functions.

If you have entered into an unwanted program menu

and are not sure where you are - do not press any

buttons for 30 seconds. The programming function

will time out after 30 seconds if there is no key stroke

activity.

4

Programming

buttons location

on powerhead.

15

OVERVIEW - REMOTES AND OPTIONS

5

FCC and IC CERTIFIED

This device complies with FCC Part 15 and RSS

210 of Industry Canada. This equipment has been

tested and found to comply with the limits for a

Class B digital device, pursuant to Part 15 of the

FCC Rules. These limits are designed to provide

reasonable protection against harmful interference

in a residential installation. This equipment

generates, uses and can radiate radio frequency

energy and, if not installed and used in accordance

with the instructions, may cause harmful

interference to radio communications. However,

there is no guarantee that interference will not

occur in a particular installation. If this equipment

does cause harmful interference to radio or

television reception, which may be determined

by turning the equipment OFF and ON, the user is

encouraged to try to correct the interference by

one or more of the following measures:

• Re-orient or relocate the receiver antenna.

• Increase the separation between the opener and

receiver.

•

Connect the opener into an outlet on a circuit

different from that to which the receiver is

connected.

• Consult your local dealer.

FIG. 5-1 Remote

WARNING

A moving door can cause serious injury or death.

1. Keep people clear of opening while door is

moving.

2. Do NOT allow children to play with opener,

including wall console, remote, or wireless

keypad.

3. During programming, the door opener could

begin to run, so keep people and objects away

from the moving door and its parts. To keep the

door from moving, close the door and disconnect

it from the rail carriage by pulling the Emergency

Release Handle. See page 19 for Release Handle

operation.

Three Button

Remote

See page 21 for battery changing instructions.

LOST OR STOLEN REMOTE - CLEARING MEMORY

Clearing remotes from powerhead memory will

clear ALL programmed remotes and wireless

keypad.

NOTE: Follow the PROGRAM REMOTE TO

POWERHEAD steps to re-enter remaining or new

remotes. See page 9.

1. Press

PR O G R A M

SE T

and hold

until both lights

come ON BLUE.

Release button.

2. Lights go out and Round

BLUE light comes ON.

3. Press

PR O G R A M

SE T

again and

long LED flashes

PURPLE.

PROGRAM

SET

—

+

PROGRAM

SET

—

+

4. Press both and

simultaneously on the

powerhead and hold until

both LEDs flash BLUE.

• Verify memory is cleared. Press a remote

button that was previously programmed to

the powerhead. Remote will not activate door

opener.

• Garage door opener will operate normally using

wall console.

• Program remaining or new remotes as shown

on page 9. Your door opener will no longer

recognize any signal received from the missing

remote, or any other which has not been

reprogrammed to the powerhead.

PR

OGRAM

SE T

—

+

16

3. Press the same button twice

to toggle IntelliCode®

selection from IntelliCode® 2

to IntelliCode® 1.

INTELLICODE® FEATURES

Other models of Genie® garage door openers,

remotes, and wireless keypads use

IntelliCode® 1 signals to communicate. Remote(s)

provided with this unit will transmit either

IntelliCode® 1 or IntelliCode® 2 signals.

Remote(s) contained in this package are preset

to IntelliCode® 2 and can be configured to

communicate with previously installed

IntelliCode® 1 openers. This dual IntelliCode®

option allows one IntelliCode® 2 remote to operate

different models of The Genie Company garage

door openers.

This new Genie® garage door opener will ONLY

accept signals from a remote sending IntelliCode®

2 signals (see page 9) or a Genie® brand

IntelliCode® 1 remote that has been programmed

to the opener using a new IntelliCode® 2 remote

(see page 10).

NOTE: Other remotes not enabled with Genie®

IntelliCode® 2 will not operate this opener.

If you have ...

Use this

IntelliCode®

programming

One or more IntelliCode® 2

openers with a maximum 3

different openers

Use IntelliCode®

2

Mixture of openers

manufactured between 1997

and 2010 (IntelliCode® 1) and

new IntelliCode® 2 openers

Use IntelliCode®

2 and/or 1

One or more openers

manufactured between 1997

and 2010 (IntelliCode® 1)

Use IntelliCode®

1

NOTE: A maximum of 3 different openers can be

programmed to a 3 button remote.

Programming remote to previously installed

IntelliCode® 1 Genie® garage door openers

Remotes provided with this unit can operate other

(IntelliCode® 1) models of Genie® garage door

openers. The default IntelliCode® 2 setting must

be changed to IntelliCode® 1. (Follow these same

steps to change IntelliCode® 1 back to IntelliCode®

2.)

The LED color displayed on the remote indicates

the IntelliCode® mode.

Red = IntelliCode® 1 / Green = IntelliCode® 2

1. Select a button on the remote that has NOT been

programmed to the

new powerhead.

2. Press and hold that

button for 10 seconds.

Both Red and Green

LEDs come ON and stay

ON.

10 SECS

4. Press the same button again

to confirm toggle. The

IntelliCode® selection for this

button is set to IntelliCode® 1.

5. Take the remote to the older Genie® garage door

opener and follow that opener's instructions to

program a new remote.

Repeat for other Genie® garage remote(s) as

necessary.

Red LED

Green LED

Three button

remote

ATTENTION

If you have another garage door opener that does NOT have

a Serial Number like this, then you will be using the

INTELLICODE® 1 setting on your remote to operate that opener.

If your garage door opener has a Serial Number sticker which

looks like this, in which the first two numbers are 10 or higher,

your opener is equipped with INTELLICODE®2.

MODEL AC SR3 THE GENIE COMPANY

FCC ID: B8Q AC SR3 Residential Door Operator

IC: 2133A CSD1D 120V 60HZ 5A

FOR H P CA 1 800 35GEN E OR WWW GEN ECOMPANY COM

S/N 10XXXX XXXXXXX

17

MAINTENANCE & TROUBLESHOOTING FOR HELP-1-800-35-GENIE OR WWW.GENIECOMPANY.COM

6

If you have any questions, please do not hesitate to contact customer service at: 1-800-35-GENIE

TRANSMITTER COMPLIANCE STATEMENT

Transmitters comply with all United States and Canadian legal requirements as of the date of manufacture.

No warranty is made that they comply with all legal requirements of any other jurisdiction. If transmitters

are to be used in another country, the importer must determine compliance with any local laws and

regulations which may differ from United States and Canadian requirements prior to use.

Los transmisores cumplen con todas las reglamentaciones legales de los Estados Unidos y del Canadá, en

la fecha de fabricación. Ninguna garantía se da que cumplan con todas las reglamentaciones legales de

ninguna otra jurisdicción. Si los transmisores se van a utilizar en otro país, el importador debe determinar

si cumplen con las reglamentaciones y leyes locales que puedan ser diferentes a las reglamentaciones de

los Estados Unidos y del Canadá, antes de usar los mismos.

Les émetteurs sont conformes à la réglementation américaine et canadienne à compter de leur date de

fabrication. Aucune garantie n’est stipulée indiquant qu’ils sont conformes à toutes les prescriptions

juridiques d’autres autorités. Si les émetteurs sont utilisés dans d’autres pays, il incombe à l’importateur

d’en déterminer leur conformité aux lois et règles locales pouvant différer de celles des États-Unis et du

Canada avant toute utilisation desdits émetteurs.

Sendegeräte entsprechen allen gesetzlichen Bestimmungen in den USA und Kanada zum Zeitpunkt der

Herstellung. Wir übernehmen keine Gewährleistung für die Einhaltung aller gesetzlichen Bestimmungen

in anderen Ländern. Sollen Sendegeräte in anderen Ländern eingesetzt werden, so muss der Importeur

vor dem Gebrauch sicherstellen, dass die Sendegeräte auch solchen lokalen Bestimmungen entsprechen,

welche von den Bestimmungen der USA und Kanadas abweichen.

IMPORTANT SAFETY INSTRUCTIONS

WARNING: To reduce the risk of severe injury or death:

1. READ AND FOLLOW ALL INSTRUCTIONS.

2. Never let children operate or play with the door controls. Keep the remote away from children.

3. Always keep the moving door in sight and away from people and objects until the door is completely closed. NO

ONE SHOULD CROSS THE PATH OF THE MOVING DOOR.

4. NEVER GO UNDER A STOPPED, PARTIALLY OPEN DOOR.

5. Test opener monthly. The door MUST reverse on contact with a 1-1/2" high object (or a 2" x 4" board laid flat)

at the center of the doorway on the floor. After adjusting either the force or the limit of travel, retest the door

opener. Failure to adjust the opener properly may cause severe injury or death.

6. When possible, use the emergency release only when the door is closed. Use caution when using this release

with the door open. Weak or broken springs are capable of increasing the rate of door closure and increasing the

risk of severe injury or death.

7. KEEP DOORS PROPERLY BALANCED. See your garage door Owner’s Manual. An improperly balanced door

increases the risk of severe injury or death. Have a trained door system technician make repairs to cables, spring

assemblies, and other hardware.

8.

SAVE THESE INSTRUCTIONS.

• With the door closed, pull release handle

DOWN and let go to release door carriage

assembly from drive system.

• Raise door manually approximately 3’- 4’ and

release.

– Door should remain stationary or move very

slightly.

– If door moves quickly, CONTACT A TRAINED

DOOR SYSTEM TECHNICIAN.

• Close the door.

• Verify RED block in carriage is in the up position.

(refer to page 19)

– Operate door using remote or wall console.

– Door will re-attach itself to carriage assembly.

18

WARNING

• Garage door hardware (springs, cables, brackets,

pulleys, etc.) are under extreme pressure and

tension.

• DO NOT attempt to repair or adjust door

springs or any hardware, and DO NOT OPERATE

garage door automatically or manually if door

is improperly balanced or springs are broken.

– CONTACT A TRAINED DOOR SYSTEM

TECHNICIAN.

ROUTINE MONTHLY MAINTENANCE

Basic monthly maintenance tasks.

• Safe-T-Beam® System Check

• Door balance

• Contact reverse

Instructions for these tasks and others are found on

the following pages.

DOOR BALANCE (SPRING TENSION)

3’ - 4’

Sectional Door

3’ - 4’

One-Piece Door

FIG. 6-1 Door balance

WARNING

Use wall console supplied with opener. Other

approved wall consoles may be available.

Unapproved or incompatible wall consoles can

cause the opener to operate unexpectedly.

Safe-T-Beam® (STB) SYSTEM CHECK

• STB Red and Green LEDs ON steady, system OK

• STB Red LED flashes

– Check for obstruction

– Check alignment

– Verify wire routing from

STBs to STB connection in

powerhead

– Check for signal interference

from another Safe-T-Beam®

unit

• No STB Red or Green LED displayed

– Check wiring and wire connections

STB BWC IWC

NOT

USED

NOT

USED

NOT

USED

NOT

USED

FROM STBs

FROM WALL

CONSOLE

FIG. 6-2 2 x 4 under center of door opening

CONTACT REVERSE TEST (Monthly test)

The Force and Limit settings MUST be

COMPLETED before testing. (See pages 6-7)

1. Test.

• Open garage door using wall console.

– Place a 2" x 4" board (laid flat) under center of

garage door opening (Fig. 6-2).

• Close garage door using wall console.

• When door contacts board, the door must

stop (within 2 seconds) and reverse direction

returning to open position.

2. Adjustment.

• If the door:

– Stops before it contacts the 2 x 4 board, it may

simply be responding to an improperly set

down limit. Return to pages 6-7 and repeat

steps 1 through 10 to correct down limit.

– Stops after contacting the 2 x 4 board and

does not reverse, it may need an adjustment

to the down limit. Return to pages 6-7 and

repeat steps 1 through 10 to correct down

limit.

• Test again. Repeat as necessary until door

reverses upon contacting board.

NOT CE

F DOO

R BECOMES

OBSTRUCED

PULL DOWN ON HAND

E

TO RELEASE CARRIAGE:

1. Pull handle DOWN then let go.

2. Manually move door until carriage releases from bullet.

3. Raise or lower door manually.

DOOR

PULL

TO RECONNECT CARRIAGE:

1. Verify RED block is in the UP position.

2. Manually move door until carriage engages bullet.

3. Raise or lower door using remote or wall console.

Release

Handle

DISENGAGEENGAGE

(for installation)

TO REENGAGE PULL

DOWN AND TOWARD

POWERHEAD THEN

LET GO

(for installation)

TO DISENGAGE

PULL DOWN AND

TOWARDS DOOR

THEN LET GO

DOOR

TO RELEASE or RECONNECT CARRIAGE,

PULL DOWN AND LET GO

DOOR

FIG. 6-4 Carriage Release (cut away view)

CARRIAGE ENGAGE/DISENGAGE

Use Release Handle to manually connect or release

belt bullet to Carriage.

FIG. 6-3 Carriage Release

CHANGE LIGHT BULBS

WARNING

• Observe all safety warning and precautions!

Improper light bulb removal or replacement

could result in Death or Serious Injury.

• Disconnect power from opener before

beginning this task.

• When replacing light cover, make sure wires are

not pinched or near moving parts.

1. Disconnect power to door opener.

• Open powerhead light cover.

• Remove light bulb(s).

• Replace with maximum 100 Watt light bulb(s).

– Do NOT use light bulbs with greater than

100 Watt rating.

• Close powerhead light cover.

2. Reconnect power to door opener.

• Test light operation.

19

RESET - OPEN/CLOSE TRAVEL LIMIT

Performing all ten (10) Limits/Force setting steps

(pages 6-7) erases previous Limits/Force settings.

NOTE: The opener will not close the door

automatically unless the Safe-T-Beam® System is

installed and Limits are programmed.

MOTION DETECTOR* - OVERVIEW

(Not available on all models)

Powerheads equipped with a motion detector

sensor provide additional security when

exiting or entering the garage area.

*This sensor works by detecting body heat. Range of detection may be

reduced when the temperature in the garage is close to body temperature.

NOTE: Detector positioning on the powerhead provides

for monitoring below the powerhead.

OPERATION

• Detector sensor is always ON. There are NO user

controls or adjustments.

• Lights automatically turn ON when a change is

detected and will turn OFF after 4 minutes of no

change.

• Motion detector sensor will not turn OFF lighting

turned ON at the wall console.

• Lighting turned ON at the wall console will remain

ON until wall console turns lighting OFF or opener

is used.

Motion Detector

DOOR

20

Independent Light Control Button

Controls door opener lights from inside garage

Sure-Lock™ Button

– LOCK disables controls

after door is completely

closed

– UNLOCK allows controls to

work normally

Indicator Light

Red indicator light is always ON

When Sure-Lock™ is ON the

indicator light flashes

Open/Close Button

Open and closes door from inside garage

WALL CONSOLE - OVERVIEW

Use only the Series III wall console provided with this

unit.

Wall console has three buttons and one indicator light.

Indicator Light

Indicator light will display Red when wall console is

properly wired and Sure-Lock™ is OFF. When Sure-

Lock™ is ON indicator light flashes.

Open/Close Button

Use this button to open or close garage door. When

Sure-Lock™ is ON the Open/Close button will CLOSE

door only. Note: Constant button pressure in the

CLOSE mode will override error responses in the

powerhead and close door.

Independent Light Control Button

Use this button to turn powerhead lights ON.

Powerhead lighting will remain ON until this button

is pressed again or a door action has been completed.

Note: If opener has a Motion Detector sensor the

sensor will keep powerhead lights ON as long as

motion is detected.

Sure-Lock™ Button

When Sure-Lock™ is ON the powerhead cannot be

activated by the wall console or a remote.

• Press and hold for 5 seconds (or until Indicator

Light flashes) to activate Sure-Lock™.

• Press and release to turn Sure-Lock™ OFF.

OPTIONAL DUAL WALL CONSOLE - INSTALLATION

Use only a Series III wall console when adding a

second wall console. The optional second

Genie®

Series III wall console must be purchased separately.

OR

STB BWC IWC

NOT

USED

NOT

USED

FROM STBs

FROM WALL

CONSOLE #1

FROM WALL

CONSOLE #2

TO

POWERHEAD

WALL

CONSOLE #1

WALL

CONSOLE #2

TO WALL CONSOLE #1

W

B/W

W

B/W

W

B/W

W

B/W

BOTH TO POWERHEAD

WALL

CONSOLE #1

WALL

CONSOLE #2

STB BWC IWC

NOT

USED

NOT

USED

NOT

USED

NOT

USED

FROM STBs

FROM WALL

CONSOLE

Tip: If indicator light on wall console comes ON, but

there is NO

operation from

buttons -

verify

wall console

wire

routing

at powerhead

connector.

STB BWC IWC

NOT

USED

NOT

USED

NOT

USED

NOT

USED

FROM STBs

FROM WALL

CONSOLE

STB BWC IWC

FROM STBs

FROM WALL

CONSOLE

STB

BWC

IWC

ROM WA

OM W

OLE

SO

Wire connector

on Powerhead

Wire connector on

Powerhead

This opener has a Serial Number sticker in which the serial

numbers begin with 10 or higher.

Follow the instructions on this page.

ATTENTION

If your garage door opener has a Serial Number sticker which

looks like this, in which the first two numbers are 10 or higher,

your opener will operate using this Series III wall control.

MODEL AC SR3 THE GENIE COMPANY

FCC ID: B8Q AC SR3 Residential Door Operator

IC: 2133A-CSD1D 120V. 60HZ. 5A

FOR HE P C L 1 800 35GENIE OR WWW GEN ECOMPANY COM

S/N:10XXXX XXXXXXX

Wall consoles from other manufacturers may not work with

openers of these serial number groups. Genie® Series I wall

buttons and Series II wall consoles will not work with openers

of this serial number group.

La page charge ...

Genie 4042 Manuel utilisateur

Genie 4042 Manuel utilisateur

dans d''autres langues

Documents connexes

Autres documents