Samsung RF263BEAESG Mode d'emploi

Refrigerator

user manual

imagine the possibilities

Thank you for purchasing this Samsung product.

To receive more complete service or accessory parts,

please register your product at or contact

www.samsung.com/register

1-800-SAMSUNG (726-7864)

Free Standing Appliance

English

RF263TE****

RF263BE****

DA68-02601A(EN+FR+ES)-0.2.indb 1 2012.3.31 9:49:28 AM

02_ Safety information

safety information

SAFETY INFORMATION

Before operating the appliance, please read this

manual thoroughly and retain it for your reference.

Use this appliance only for its intended purpose as

described in this instruction manual.

This appliance is not intended for use by persons

(including children) with reduced physical, sensory

or mental capabilities, or lack of experience

and knowledge, unless they have been given

supervision or instruction concerning use of the

appliance by a person responsible for their safety.

Because these following operating instructions

cover various models, the characteristics of your

refrigerator may differ slightly from those described

in this manual.

R600a or R134a is used as a refrigerant. Check

the compressor label on the rear of the appliance

or the rating label inside the fridge to see which

refrigerant is used for your refrigerator. When

this product contains ﬂ ammable gas(Refrigerant

R600a), contact your local authority in regard to

safe disposal of this product.

When disposing of this or other refrigerator/s,

remove the door/door seals, door latch so that

children or animals cannot become trapped

inside.

Children should be supervised to ensure that they

do not enter and play with the appliance.

If trapped inside, the child may become injury •

and suffocate to death.

Important safety symbols and

precautions:

WARNING

Hazards or unsafe practices that may result in

severe personal injury or death.

CAUTION

Hazards or unsafe practices that may result in

minor personal injury or property damage.

Do NOT attempt.

Do NOT disassemble.

Do NOT touch.

Follow directions carefully.

Unplug the power plug from the wall socket.

Make sure the refrigerator is grounded to

prevent electric shock.

Call the contact center for help.

Note.

These warning signs are here to prevent

injury to you and others.

Please follow them carefully.

After reading this section, keep it in a safe

place for future reference.

SEVERE WARNING SIGNS

FOR INSTALLATION

• Do not install the refrigerator in a damp

place or place where it may come in

contact with water.

Deteriorated insulation of electrical parts may -

cause an electric shock or ﬁ re.

Do not place this refrigerator in direct sunlight •

or expose to the heat from stoves, room

heaters or other appliance.

Do not plug several appliances into the same •

multiple power strip. The refrigerator should

always be plugged into its own individual

electrical outlet which has a voltage rating that

matches the voltage listed on the refrigerator’s

rating plate.

This provides the best performance and -

also prevents overloading house wiring

circuits, which could cause a ﬁ re hazard from

overheated wires.

If the wall socket is loose, do not insert the •

power plug.

There is a risk of electric shock of ﬁ re. -

Do not use a cord that shows cracks or •

abrasion damage along its length or at either

end.

Do not bend the power cord excessively or •

place heavy articles on it.

Do not pull or excessively bend the power -

cord.

Do not twist or tie the power cord.•

Do not hook the power cord over a metal •

object, place a heavy object on the power

cord, insert the power cord between objects,

or push the power cord into the space behind

the appliance.

When moving the refrigerator, be careful not to -

roll over or damage the power cord.

This may result in an electric shock or ﬁ re. -

WARNING

Safety information _03

This appliance should be positioned in such a •

way that it is accessible to the power plug.

Failing to do so may result in an electric shock -

or ﬁ re due to electric leakage.

Keep ventilation opening in the appliance •

enclosure or mounting structure clear of

obstruction.

Do not attempt to repair, disassemble, or •

modify the appliance yourself.

Do not use any fuse(such as cooper, steel wire, -

etc.) other than the standard fuse.

hen repairing or reinstalling the appliance is -

required, contact your nearest service center.

Failing to do so may result in an electric shock, -

ﬁ re, problems with the product, or injury.

To get the best energy efﬁ ciency of this •

product, please leave all selves, drawers and

baskets on their original position like as above

illustration.

Never unplug your refrigerator by pulling on the •

power cord. Always grip plug ﬁ rmly and pull

straight out from the outlet.

Damage to the cord may cause a short-circuit, -

ﬁ re and/or electric shock.

Do not use aerosols near the refrigerator.•

Aerosols used near the refrigerator may cause -

an explosion or ﬁ re.

Do not install this appliance near a heater, •

inﬂ ammable material.

Do not install this appliance in a humid, oily or •

dusty location, in a location exposed to direct

sunlight and water (rain drops).

Do not install this appliance in a location where •

gas may leak.

This may result in an electric shock or ﬁ re. -

• This refrigerator must be properly

installed and located in accordance with

the manual before you use it.

Connect the power plug in the proper position •

with the cord hanging down.

If you connect the power plug upside down, -

the wire can get cut off and cause a ﬁ re or

electric shock.

When moving the refrigerator, be careful not to •

roll over or damage the power cord.

This constitutes a ﬁ re hazard. -

Make sure that the power plug is not squashed •

or damaged by the back of the refrigerator.

Keep the packing materials out of reach of •

children.

There is a risk of death from suffocation if a -

child puts the packing materials on his or her

head.

The appliance must be positioned so that the •

plug is accessible after installation.

You need to remove all the protective plastic •

ﬁ lm before you initially plug the product in.

• The refrigerator must be safely

grounded.

Always make sure that you have -

grounded the refrigerator before

attempting to investigate or repair any

part of the appliance. Power leakages

can cause severe electric shock.

Never use gas pipes, telephone lines or other •

potential lightning attractors as an electrical

ground.

Improper use of the grounding plug can result -

in a risk of electric shock. If it is necessary

to use an extension cord, use only a 3-wire

extension cord that has a 3-blade grounding

plug and a 3-slot receptacle that will accept

the plug on the appliance. The marked rating

of the extension cord should be AC115-120 V,

10 A, or more. If a grounding adapter is used,

make sure the receptacle box is fully grounded.

• If the power cord is damaged,

have it replaced immediately by the

manufacturer or its service agent.

INSTALLATION CAUTIONS

• Allow sufﬁ cient space to install the

refrigerator on a ﬂ at surface.

If your refrigerator is not level, the internal -

cooling system may not work correctly.

Keep the ventilation space in the appliance •

enclosure or mounting structure clear of

obstruction.

Allow the appliance to stand for 2 hours after •

installation.

We recommend you have installed this •

refrigerator by a qualiﬁ ed technician or service

company.

Failing to do so may result in an electric shock, -

ﬁ re, explosion, problems with the product, or

injury.

This appliance must be properly grounded.•

Do not ground the appliance to a gas pipe, •

plastic water pipe, or telephone line.

You must ground the refrigerator to prevent -

any power leakages or electric shocks caused

by current leakage from the refrigerator.

This may result in an electric shock, ﬁ re, -

explosion, or problems with the product.

CAUTION

04_ Safety information

Never plug the power cord into a socket that is -

not grounded correctly and make sure that it is

in accordance with local and national codes.

Plug the power plug into the wall socket ﬁ rmly. •

Do not use a damaged power plug, damaged

power cord or loose wall socket.

This may result in an electric shock or ﬁ re. -

The installation or any service of this appliance •

is recommended by a qualiﬁ ed technician or

service company.

Failing to do so may result in an electric shock, •

ﬁ re, explosion, problems with the product, or

injury.

Do not touch the power plug with wet hands.•

This may result in an electric shock. -

Do not store articles on the top of the •

appliance.

When you open or close the door, the articles •

may fall and cause personal injury and/or

material damage.

Do not use or place any substances sensitive •

to temperature such as inﬂ ammable sprays,

inﬂ ammable objects, dry ice, medicine, or

chemicals near or inside of the refrigerator.

Do not keep volatile or inﬂ ammable objects or •

substances (benzene, thinner, propane gas,

alcohol, ether, LP gas and other such products

etc.) in the refrigerator.

This refrigerator is for storing food only. -

This may result in ﬁ re or explosion. -

If you smell pharmaceutical or smoke, pull •

out power plug immediately and contact your

Samsung Electronics service center

CRITICAL USAGE

WARNINGS

• Do not insert the power plug with wet

hands.

Do not store articles on the top of the •

appliance.

When you open or close the door, the articles -

may fall and cause personal injury and/or

material damage.

Do not put a container ﬁ lled with water on the •

refrigerator.

If spilled, there is a risk of ﬁ re or electric shock. -

Children should be supervised to ensure that •

they do not play with the appliance.

Keep ﬁngers out of “pinch point” areas; -

clearances between the doors and cabinet are

necessarily small. Be careful when you open

the doors when children are in the area.

Do not let children hang on the door. A serious •

WARNING

injury may occur.

Do not let children go inside the refrigerator.•

Children could become trapped.

Do not insert your hands into the bottom area •

under the appliance.

Any sharp edges may cause personal injury. -

Do not let children step on a drawer’s cover.•

The drawer may break and cause them to slip. -

Do not overﬁ ll the refrigerator with food.•

When you open the door, an item may fall out -

and cause personal injury or material damage.

Do not touch the inside walls of the freezer or •

products stored in the freezer with wet hands.

This may cause frostbite. -

Never put ﬁ ngers or other objects into the •

water dispenser hole, ice chute, or ice maker

bucket.

It may cause personal injury or material -

damage.

Do not spray ﬂ ammable gas near the •

refrigerator.

There is a risk of explosion or ﬁ re. -

Do not store volatile or ﬂ ammable substances •

in the refrigerator.

The storage of benzene, thinner, alcohol, ether, -

LP gas and other such products may cause

explosions.

Do not store pharmaceuticals products, •

scientiﬁ c materials, or temperature sensitive

products in the refrigerator.

Products that require strict temperature -

controls must not be stored in the refrigerator.

Do not place or use an electrical appliance •

inside the refrigerator, unless it is of a type

recommended by the manufacturer. Do not

stand on top of the appliance or place objects

(such as laundry, lighted candles, lighted

cigarettes, dishes, chemicals, metal objects,

etc.) on the appliance. This may result in an

electric shock, ﬁ re, problems with the product,

or injury. Do not put a container ﬁ lled with

water on the appliance.

If spilled, there is a risk of ﬁ re or electric shock. -

Do not use mechanical devices or any other •

means to accelerate the defrosting process,

other than those recommended by the

manufacturer.

Do not damage the refrigerant circuit.•

Do not spray volatile material such as •

insecticide onto the surface of the appliance.

As well as being harmful to humans, it may -

also result in an electric shock, ﬁ re or problems

Safety information _05

with the product.

Never stare directly at the UV LED lamp for t

long periods of time.

This may result in eye strain due to the -

ultraviolet rays.

t Do not disassemble or repair the

refrigerator by yourself.

You run risk of causing a ﬁ re, malfunction and/ -

or personal injury.

When the interior or exterior LED lamp has -

gone out, please contact your service agents.

t Children should be supervised to ensure

that they do not play with the appliance.

Keep ﬁ ngers out of “pinch point” areas : -

clearances between the doors and cabinet are

necessarily small. Be careful when you open

the doors when children are in the area. Do not

let children hang on the door. If not, a serious

injury may occur. Risk of children entrapment.

Do not let children enter inside the refrigerator.

Bottles should be stored tightly together so t

that they do not fall out.

This product is intended only for the storage of t

food in a domestic environment.

If a gas leak is detected, avoid any naked t

ﬂ ames or potential sources of ignition and air

the room in which the appliance is standing for

several minutes.

Do not touch the appliance or power cord. -

Do not use a ventilating fan. -

A spark may result in explosion or ﬁ re. -

If the products is equipped with the LED Lamp, t

do not disassemble Lamp Cover and LED

Lamp by yourself.

Please contact your service agent. -

Use only the LED Lamps provided by t

manufacturer or service agent.

Allow the appliance to stand for 2 hours after a)

installation.

To get Best performance from the product,b)

Do not place foods too closely in front of 1)

the vents at the rear of the appliance as

it can obstruct free air circulation in the

freezer compartment.

Wrap the food up properly or place it in 2)

airtight containers before putting it into the

fridge or freezer.

Do not put any newly introduced food for 3)

freezing near to already existing food.

Do not place glass or bottles or carbonated c)

beverages into the freezer.

The container may freeze and break, -

and this may result in injury.

Please observe maximum storage times and d)

expiry dates of frozen goods.

There is no need to disconnect the refrigerator e)

from the power supply if you will be away for

less than three weeks. But, Remove all the

food if you are going away for the three weeks

or more. Unplug the refrigerator and clean it,

rinse and dry.

Remove all foreign substances such as dust t

or water from the power plug terminals and

contact points using a dry cloth on a regular

basis.

Unplug the power plug and clean it with a dry -

cloth.

Failing to do so may result in an electric shock -

or ﬁ re.

Before cleaning or performing maintenance, t

unplug the appliance from the wall socket.

Failing to do so may result in an electric shock -

or ﬁ re.

t If there are burning smells or smoke, pull

out power plug immediately and contact

your Samsung Electronics service

center.

If you experience difﬁ culty when changing the t

light, contact a service agent.

If the product is equipped with LED Lamps, t

do not disassemble the Lamp Cover and LED

Lamp by yourself.

Please contact your service agents. -

If any dust or water is in refrigerator, pull out t

the power plug and contact your Samsung

Electronics service center.

Otherwise there is a risk of ﬁ re. -

USAGE CAUTIONS

t Do not re-freeze frozen foods that

have thawed completely. Do not place

carbonated or ﬁ zzy drinks in the freezer

compartment. Do not put bottles or

glass containers in the freezer.

When the contents freeze, the glass may break -

and cause personal injury.

Use only the ice maker provided with the t

refrigerator. The water supply to this refrigerator

must only be installed/connected by a suitably

qualiﬁ ed person and connected to a potable

water supply only. In order to operate the

ice maker properly, water pressure of 20 ~ 125 psi

CAUTION

06_ Safety information

is required. If you have a long vacation

or business trip and won’t use water or ice

dispensers, close the water valve.

Otherwise, water leakage may occur. -

Wipe excess moisture from the inside and

leave the doors open.

Otherwise, odor and mold may develop. -

Service warranty and Modiﬁ cation.

Any changes or modiﬁ cations performed -

by a 3rd party on this ﬁ nished appliance

are not covered under Samsung

warranty service, nor can Samsung be

responsible for safety issues that result

from 3rd party modiﬁ cations.

Do not block air holes.

If the air holes are blocked, especially with a -

plastic bag, the refrigerator can be over cooled.

If this cooling period lasts too long, the water

ﬁ lter may break and cause water leakage.

If the refrigerator is disconnected from the

power supply, you should wait for at least ﬁ ve

minutes before plugging it back in.

If you have a long vacation planned or the

refrigerator is not to be used for a long period

of time, you must empty the refrigerator and

pull out the power plug.

Letting the refrigerator run for a long time -

without using it can cause the insulation to

deteriorate and may cause a ﬁ re.

Wipe excess moisture from the inside and -

leave the doors open. Otherwise, odor and

mold may develop.

To get the best performance from the product:

Do not place foods too close to the vents at -

the rear of the appliance as it can obstruct free

air circulation in the refrigerator compartment.

Wrap food up properly or place it in airtight -

containers before putting it into the refrigerator.

Fill the water tank, ice tray, and water cubes

only with potable water.

If the product is ﬂ ooded, make sure to

contact your nearest service center.

There is a risk of electric shock or ﬁ re. -

CLEANING CAUTIONS

Do not directly spray water on the inside

or outside the refrigerator.

There is a risk of ﬁ re or electric shock. -

Do not use a hair dryer to dry the inside of the

refrigerator. Do not place a lighted candle in

CAUTION

the refrigerator to remove bad odors.

This may result in an electric shock or ﬁ re. -

Remove any foreign matter or dust from

the power plug pins. Do not use a wet

or damp cloth when cleaning the plug.

Otherwise, there is a risk of ﬁ re or electric -

shock.

Unplug the refrigerator before cleaning

or making repairs.

WARNING

This product contains chemicals known to

the State of California to cause cancer and

reproductive toxicity.

CRITICAL DISPOSAL

WARNINGS

Risk of child entrapment. Before you

throw away your old refrigerator or

freezer:

-

Leave the shelves in place so that children can -

not easily climb inside.

Please dispose of the packaging material from

this product in an environmentally friendly

manner.

Leave the shelves in place so that children

can not easily climb inside. Ensure that none

of the pipes on the back of the appliance are

damaged prior to disposal.

R600a or R134a is used as a refrigerant.

Check the compressor label on the rear of

the appliance or the rating label inside the

fridge to see which refrigerant is used for your

refrigerator. If this product contains ﬂ ammable

gas (Refrigerant R600a), contact your local

authority in regard to safe disposal of this

product.

When disposing of this refrigerator, remove the

WARNING

Safety information _07

contents

SETTING UP YOUR FRENCH DOOR REFRIGERATOR ……………………………………………… 08

OPERATING YOUR FRENCH DOOR REFRIGERATOR ………………………………………………… 16

TROUBLESHOOTING ……………………………………………………………………………………… 28

door/door seals and door latch so that small

children or animals cannot become trapped

inside. Children should be supervised to ensure

that they do not play with the appliance.

Cyclopentane is used in the insulation. The t

gases in the insulation material require a special

disposal procedure. Please contact your local

authorities in regard to the environmentally safe

disposal of this product. Ensure that none of

the pipes on the back of the refrigerator are

damaged prior to disposal.

When you use this function the energy t

consumption of the refrigerator will increase.

Remember to turn it o when you don’t t

need it and return the freezer to your original

temperature setting.

power freezing

If you need to freeze large amount of food t

stu, activate Power Freeze function at least

24 hours before.

Never put ﬁ ngers or other objects into the t

dispenser hole, ice chute and ice maker

bucket.

It may cause a personal injury or material -

damage.

08_

setting up

Setting up your French Door

Refrigerator

GETTING READY TO INSTALL

THE REFRIGERATOR

Congratulations on your purchase of this Samsung

French Door Refrigerator.

We hope you enjoy the state-of-art features and

A location with easy access to a water supply.

Choose:

A location without direct exposure to sunlight.

A location with a level ﬂoor.

A location with enough space for the

refrigerator doors to open easily.

A location that allows sufﬁcient space to the

right, left, back and top for air circulation.

A location that allows you to move the

refrigerator easily if it needs maintenance or

service.

Do not install the refrigerator where the

temperature will go below 50ºF (10ºC).

When moving your refrigerator

To prevent ﬂoor damage, be sure the front

adjusting legs are in the up position (above

the ﬂoor). Refer to ‘Adjusting the Level’ in

the manual (on page 9).

B

A

C

E

D

B

A

C

E

D

Flat-blade screw

driver(-)

Control Lever

CAUTION

DA68-02601A(EN+FR+ES)-0.2.indb 6 2012.3.31 9:49:31 AM

Model

Depth “A” 33 27/32” (860mm)

Width “B” 35 25/32” (909mm)

Height “C” 68 3/8” (1737mm)

Overall Height “D”

Depth “E” 36 7/32” (920mm)

The measurements here are based on

depending on the measuring method.

Do not locate the refrigerator where it may

become wet.

140

°

140

°

2”

(50 mm)

13 3/4”

(340 mm)

63 25/32”

(1620 mm)

1 37/64”

(40 mm)

3 3/4”

(95 mm)

29 6/64”

(740 mm)

48 1/32”

(1220 mm)

35 25/32”

(909 mm)

Selecting the best location for the refrigerator

70” (1778 mm)

RF263T**/ RF263B**

setting up

_09

01 SETTING UP

FLOORING

For proper installation, you must place this

refrigerator on a level, hard surface that is the

same height as the rest of the ﬂoor. This surface

should be strong enough to support a fully loaded

refrigerator, or approximately 335lbs (152kg).

To protect the ﬁnish of the ﬂooring, cut a large

section of the cardboard carton and place it under

the refrigerator where you are working. When

moving the refrigerator, you need to pull and push

it straight forwards or back. Do not wiggle it from

side to side.

ACCESSORIES AND

REQUIRED TOOLS

The following accessories are included with your

refrigerator:

Hex wrench Fastener

Required Tools (Not provided)

You need the following tools to complete the

installation of your refrigerator:

Philips

screwdriver(+)

Flat-blade screw

driver(-)

Socket wrench

(10mm)

Pliers

Allen wrench

(3/16”) (5mm)

REMOVING THE REFRIGERATOR

DOORS

For some installations you need to remove the

fridge and freezer drawers so you can move the

refrigerator to its ﬁnal location.

Do not remove

the doors/drawer if you don’t need to. If you do

not need to remove the refrigerator doors, go

to Adjusting the Level on page 9. If you need to

remove the doors. continue below.

Before removing the door/drawer, make sure you

read the following items:

Disconnect power to the refrigerator before

removing the door or drawer.

Be careful not to drop, damage or scratch

the door/drawer while removing them.

Reattach the doors/drawer properly to avoid:

- Moisture from air leakage.

- Uneven door alignment.

- Wasting energy due to improper door seal.

Use care when you remove the doors/drawer. The

doors are heavy and you could injure yourself.

WARNING

DA68-02601A(EN+FR+ES)-0.2.indb 7 2012.3.31 9:49:32 AM

HOW TO ASSEMBLE THE HANDLE

Orient each handle so that the end with the sticker

attached is at the top and the holes with the

tightening screws are facing each other.

Then, follow the directions below to install each

handle.

By using Phillips screwdriver, ﬁx the screw

(optional) and then put the handle on the

xer by sliding them down ﬁrmly.

setting up

_10

Fix the handles to the doors by sliding them left

side ﬁrmly.

4

3

DA68-02601A(EN+FR+ES)-0.2.indb 7 2012.3.31 9:49:32 AM

2

1

Fix the handles to the doors by

sliding them down ﬁrmly.

3

5

4

Tighten with wrench ﬁ

Drawer door handle assembly

Check the direction of Handle

assembly.

1

2

Fix the handles to the doors by

sliding them left side ﬁrmly.

5

Tilt up the Handle bar and tighten with wrench

ﬁrmly.

Disassemble the refrigerator doors

Be careful not to drop and scratch the

doors while removing them.

WARNING

With the door opened

Remove 3 screws holding down the TOP 1.

TABLE ( 1 ) and turn it with wires connected.

1

Screw

11_

setting up

Disconnect two connectors ( 2. 2 ) on the left side

door. To remove the water coupler from the

hinge, twist and pull it from the hinge. Remove

the water line ( 3 ) while pressing the marked

part ( 4 ) of the water line coupler.

If a red clip is on the coupler, it must be

removed before removing the tube.

Pull and remove the hinge lever ( 3. 5 ) . Remove

the ground screw ( 6 ) attached to the upper

left door hinges with a philips screwdriver (+).

Remove the upper left and right door hinges

( 7 ).

Lift the door straight up to remove.4.

Remove the screw (5. 8 ) attached to the

lower left and right door hinges with a philips

screwdriver (+). Remove the 2 hex head bolts

( 9 ) attached to the lower left and right door

hinges with an allen wrench (3/16”). Remove

the lower left and right door hinges ( 10 ).

REATTACHING THE

REFRIGERATOR DOORS

To reattach the fridge doors after you have moved

the fridge to its ﬁnal location, assemble the parts in

reverse order.

The Water Line must be fully Inserted to the 1.

center of transparent coupler to prevent water

leakage from the dispenser.

Insert2.

the clip in the top plate and check that it

By placing the 3 screws again ensure that the wires

are in not to damage the harness.

DISASSEMBLE THE FLEX DOOR

Take out the upper drawer by lifting it up.1.

Take out the lower basket ( 2.

1

) by lifting the

basket up from the rail system.

Press the ﬁxing hook of rail system. 3.

CAUTION

2

3

4

Red Clip

(1/4")

5

6

7

Allen wrench

10

8

9

1

DA68-02601A(EN+FR+ES)-0.2.indb 8 2012.3.31 9:49:38 AM

01 SETTING UP

setting up

_12

Holding the top of the Freezer Drawer, pull it out

all the way and then remove it from the rail system.

4.

Be careful not to scratch or dent the sliding

Make sure that you mount the freezer

basket in the right position when removing

/ installing the freezer door. Failing to do

so may result in the door not opening or

closing properly.

ASSEMBLE THE FREEZER

DRAWER

To reattach the drawer after you have moved

the fridge to its ﬁnal location, assemble the parts in

reverse order.

ADJUSTING THE LEVEL

Make sure the refrigerator is level so that you can

make ﬁnal adjustments. Use a level to test if the

refrigerator is level both side to side and back to

front. If the refrigerator is not level, it will not be

possible to get the doors perfectly even, which

may cause moisture condensation and increased

energy bills. Below is an example of how to level

the refrigerator if the left side of the refrigerator is

lower than the right side.

How to adjust the level

Open the freezer drawer and remove the lower 1.

basket.

Insert a ﬂat-blade screwdriver (-) into a notch 2.

on the left control lever, and turn it counter

clockwise to level the refrigerator. (You turn the

lever clockwise to lower the refrigerator and

counterclockwise to raise it.)

Both control levers must be touching the

ﬂoor to avoid possible personal injury or

property damage because of tipping.

If the right side is lower, perform the same

procedure, but with the right control lever.

It is difﬁcult to remove the cover leg

front from the refrigerator, so we do not

recommend making small adjustments

with the control lever. Instead, refer to the

next page for the best way to make minor

adjustments to the doors.

MAKING MINOR

ADJUSTMENTS BETWEEN

DOORS

Remember, a leveled refrigerator is necessary

for getting the doors perfectly even. If you need

help, review the previous section on leveling the

refrigerator.

The left door is ﬁxed. To make minor

adjustments between doors, adjust only

the right door.

CAUTION

ﬂat-blade screwdriver(-)

Control Lever

CAUTION

Adjustment

part

Fixed part

DA68-02601A(EN+FR+ES)-0.2.indb 9 2012.3.31 9:49:42 AM

13_

setting up

Pull out the freezer drawer ( 1. 1 ) to reveal

the lower hinge (

2

).

Insert the supplied allen wrench (3/16”) ( 2. 3 )

into the shaft ( 4 ) of the lower hinge.

Adjust the height by turning the 3.

hex wrench ( 3 ) clockwise (

DOWN

) or counter

clockwise (

UP

).

When you turn the hex wrench counter-

clockwise(

), the door will move up.

After adjusting the doors, insert the supplied 4.

fastener ( 6 ) using a pliers ( 5 ) in the gap

between the hinge-grommet ( 7 ) and the lower

hinge ( 8 ). The number of fasteners you’ll need

to insert depends on the gap.

2 fastener are enclosed with the refrigerator.

The thickness of each fastener is 0.04”.

INSTALLING THE WATER

DISPENSER LINE

A water dispenser with a ﬁlter is one of the helpful

features on your new refrigerator. To help promote

better health, the water ﬁlter removes unwanted

particles from your water. However, it does not

sterilize or destroy microorganisms. You may need

to purchase a water purifying system to do that.

The water line also connects to the ice maker.

For the ice maker to operate properly, water pressure

of 20~125psi ( 138~862kPa) is required.

If the refrigerator is installed in an area with low

water pressure (below 20psi), you can install

a booster pump to compensate for the low

pressure.

After you have connected the water line, make

sure the water storage tank inside the refrigerator

is properly ﬁlled. To do this, press the water

dispenser lever until the water runs from the water

outlet.

Water line installation kits are available at

extra cost from your dealer.

We recommend using a water line

installation kit that contains copper tubing

and ¼” compression nut.

Connecting to the water supply line

1.

supply.

Locate the nearest cold water drinking line and 2.

Connect the water line installation kit to the 3.

Connecting the water supply line to

the refrigerator.

There are several items that you need to purchase

to complete this connection.

You may ﬁnd these items sold as a kit at your local

hardware store.

Use Copper Tubing Use Plastic Tubing

¼” copper tubingt

¼” compression nut (1pc)t

Ferrule (2pc)t

¼” plastic tubing t

Molded end(Bulb)

¼” compression nut (1pc)t

Pipe clamp

Cold water line

Shut off valve

Pipe clamp

Cold water line

Water line installation kit

3

1

2

3

4

DA68-02601A(EN+FR+ES)-0.2.indb 10 2012.3.31 9:49:43 AM

01 SETTING UP

setting up

_14

Connect the household water line to the 1.

assembled compression ﬁtting.

If you are using copper tubing, slip the -

compression nut ( B ) (not supplied) and

ferrule (not supplied) on the copper tubing (not

supplied) as shown.

If you are using plastic tubing ( - B ) , insert the

molded end (Bulb) of the plastic tubing ( B )

into the compression ﬁtting.

Do not use without the molded end (Bulb)

of the plastic tubing ( B ).

Tighten the compression nut ( 2. B ) onto the

compression ﬁtting.

Do not over-tighten the compression nut ( B ) .

Turn water on and check for any leakage. If you 3.

ﬁnd water drops or leakage in the connection

the connections and, if necessary, tighten.

Flush 1 gallon of water through the ﬁlter 4.

before drinking or using the water from the

refrigerator. (Flush approximately 6 minutes.)

To ﬂush, press a large glass or cup against the

water dispenser lever. Fill the glass, empty it

into the kitchen sink after it is ﬁlled, and then

repeat.

After you turn on the refrigerator, let the ice 5.

maker make ice for 1 to 2 days. Over that

period of time, throw out the ﬁrst 1 or 2

buckets of ice the freezer makes to ensure all

impurities have been removed from the water

line.

Only connect the water line to a drinkable

water source.

If you have to repair or disassemble the water line,

get a snug, leak-free connection.

You can test the water line quickly using a

paper cup.Under normal conditions, the water

10 seconds.

COMPLETING THE SET UP

Now that you have your new refrigerator installed

in place, you are ready to set up and enjoy the

features and functions of the appliance.

By completing the following steps, your refrigerator

should be fully operational.

Make sure your refrigerator is in an appropriate 1.

location with reasonable clearance between it

and the wall. Refer to installation instructions in

this manual.

Once the refrigerator is plugged in, make sure 2

.

the interior light comes on when you open the

doors.

Set the Temperature control to the coldest 3.

temperature and wait for an hour. The freezer

will get slightly chilled and the motor will run

smoothly. Reset the refrigerator and freezer to

the temperatures you want.

After you plug the refrigerator in, it will 4.

take a few hours to reach the appropriate

temperature. You can store food and drinks

in the refrigerator after the temperature is

sufﬁciently cool.

Compression

Nut (1/4”)

(Assembled)

Ferrule

(Not supplied)

Plastic Tubing

(Assembled)

Compression

Fitting

(Assembled)

Molded

end(Bulb)

Compression

nut (B) (1/4”)

(Not supplied)

or

Copper tubing

(Not supplied)

Plastic tubing (B)

(Not supplied)

Household water supply line

Refrigerator

CAUTION

DA68-02601A(EN+FR+ES)-0.2.indb 11 2012.3.31 9:49:44 AM

In the event of a power failure, call the local ofﬁ ce

of your Electricity Company and ask how long it is

going to last.

Most power failures that are corrected in an -

hour or two will not aect your refrigerator

temperatures. However, you should minimize

the number of door openings while the power

is o.

But Should the power failure last more than -

24hours, remove all frozen food.

If the key is provided with refrigerator, the keys

should be kept out of the reach of children and

not be in the vicinity of the appliance.

The appliance might not operate consistently

(possibility of defrosting of co tents or

temperature becoming too warm in the frozen

food compartment) when sited for an extended

period of time below the cold end of the range of

temperatures for which the refrigerating appliance

is designed.

15_

setting up

Do not store food which goes bad easily at low

temperature, such as bananas, melons.

Your appliance is frost free, which means there is

no need to manually defrost your appliance, as

this will be carried out automatically.

Temperature rise during defrosting can comply

with ISO requirements. But If you want to prevent

an undue rise in the temperature of the frozen

food while defrosting the appliance, please wrap

the frozen food up in several layers of newspaper.

Any increase in temperature of frozen food during

defrosting can shorten its storage life.

Do not re-freeze frozen foods that have thawed

completely.

Install the appliance in a cool, dry room with

adequate ventilation.

Ensure that it is not exposed to direct sunlight and

never put it near a direct source of heat (radiator,

for example).

Never block any vents or grilles on the appliance.

Allow warm food to cool down before placing it in

the appliance.

Put frozen food in the refrigerator to thaw. You

can then use the low temperatures of the frozen

products to cool food in the refrigerator.

Do not keep the door of the appliance open for

too long when putting food in or taking food out.

The shorter time for which the door is open, the

less ice will form in the freezer.

Allow clearance to the right, left, back and top

when installing.

This will help reduce power consumption and

keep your energy bills lower.

01 SETTING UP

16_

operating

Operating your French Door

Refrigerator

USING THE CONTROL PANEL

( 1 ) Energy

Saver

Hold 3 sec for

°C

°F

Touching this button turns Energy Saver

Saver on, the Energy Saver icon lights.

automatically turns on when power is

supplied to the refrigerator.

If condensation or water drops appear

on the doors, turn the Energy Saver

Touch and hold this button for 3

seconds to switch the temperature units

between °C and °F.

( 2 ) Freezer

(Hold 3 sec

for Power

Freeze)

Touch this button to set the freezer to

your desired temperature.

You can set the temperature between

-8°F and 5°F (between -23°C and

-15°C). Touch and hold this button for 3

seconds to decrease the time needed

to freeze products in the Freezer. It can

be helpful if you need to quickly freeze

easily spoiled items or if the temperature

in the freezer has warmed dramatically

(For example, if the door was left open).

( 3 ) Ice

Type/Water

Hold 3 sec for

Filter Reset

Touch this button to select the ice or

water function. You can select water or

the types of ice(cubed/crushed ice).

Each time you press the button, the

cubed and crushed

ice modes alternate and the Cubed or

Crushed ice icon lights up, indicating

your selection.

After you replace the water ﬁlter, touch

and hold this button for 3 seconds to

reset the water ﬁlter life indicator.

( 4 ) Alarm

Hold 3 sec for

Lighting

If the door alarm is set to On, an alarm

beeps if any refrigerator door is left open

for more than three minutes. The beeping

stops when you close the door. The door

alarm function is preset to On int the factory

back on in the same fashion. The icon lights

up when the function is on.

releasing this button. You can turn it back

If you touch and hold the Alarm/Lighting

button for 3 seconds, the dispenser LED

the button for 3 seconds again.

( 5 ) Fridge

Hold 3 sec for

Power Cool

Touch this button to set the fridge to

your desired temperature. You can set

the temperature between 34 °F and 44 °F

(between 1°C and 7 °C ). Touch and hold

this button for 3 seconds to decrease

the time needed to cool products in

the Refrigerator. It can be helpful if you

need to quickly cool easily spoiled items

or if the temperature in the fridge has

warmed dramatically (For example, if the

door was left open).

( 6 ) Ice Off

Hold 3 sec for

Child Lock

If you don’t want to make more ice,

for 3 seconds turns

Touching this button

the display

on Child Lock which locks

panel and dispenser buttons so the

buttons can not be used. The Child Lock

icon lights up to indicate you’ve activated

the Child Lock function. Press 3 seconds

to unlock. The Child Lock are not going to

lock the Cool Pantry. The lights and motors start

( 7 ) Ice Off

If you don’t want to make more ice,

The icon will light up and the Ice-Maker

stops making ice.

We recommend you to stop ice

making if the following occur:

-

There is enough ice in the ice bucket.

-

You want to save water and energy.

- Water is not being supplied to

the refrigerator.

If the ice maker function is

ON, and the water Line is not

connected, there will be a water

valve noise from the back of the

unit, press the Ice Off (Hold 3sec

for child lock) button for less

than 3 seconds until the Ice Off

Indicator (

) illuminates.

(RF263T**)

(RF263B/N**)

8

7

1

2

3

5

6

4

DA68-02601A(EN+FR+ES)-0.2.indb 12 2012.3.31 9:49:44 AM

operating

_17

( 8 ) Filter Water ﬁlter usage

This icon will light up when you need to

change the ﬁlter. After you use about

300 gallons of water, the ﬁlter indicator

lights up. (about 6 months). After you

install the new water ﬁlter, reset the ﬁlter

indicator by touching the Ice Type Water/

Hold 3 sec for Filter Reset button.

If water is not dispensing or t

dispensing slowly, you need to

replace the water ﬁlter because

the water ﬁlter is clogged.

Some areas have large amounts t

of lime in their water, which

causes the water ﬁlter to clog

more quickly.

Cooling Off

Mode

mode), is designed for use by retailers

when they are displaying refrigerators on

refrigerator’s fan motor and lights work

normally, but the compressor does not

run, and the refrigerator and freezer do

touch and hold the Energy Saver button

and the Freezer button for 5 seconds

during normal operation. The refrigerator

chime sounds and the temperature

display ﬂashes OF OF.

hold the Energy Saver and the Freezer

buttons again for 5 seconds.

CHANGING THE WATER FILTER

To reduce risk of water damage to your

property DO NOT use generic brands

of water ﬁlters in your SAMSUNG

Refrigerator.

USE ONLY SAMSUNG BRAND WATER FILTERS.

SAMSUNG will not be legally responsible for any

damage, including, but not limited to property

damage caused by water leakage from the use of

a generic water ﬁlter. SAMSUNG Refrigerators are

designed to work ONLY WITH SAMSUNG Water

Filter.

The Filter light turns red to let you

know when it is time to change your

water ﬁlter cartridge.

To give you time to get a new ﬁlter,

the red light comes on just before the

capacity of the current ﬁlter runs out.

Changing the ﬁlter on time provides you with the

freshest, cleanest water from your refrigerator.

1.

ﬁlter ( 1 ) about 1/4 turn, counter-clockwise.

Pull the water ﬁlter ( 2. 1 ) from the case ﬁlter ( 2 ).

To change the water ﬁlter more easily, t

Sometimes, it is hard to disassemble the water t

ﬁlter because impurities in the water cause it

to stick. If you are having difﬁculties, grip the

water ﬁlter ﬁrmly and pull it hard.

When you pull the t

water ﬁlter, a little

water can leak from

the opening. This is

normal. To minimize

the water leaks, keep

the ﬁlter cartridge horizontal when you pull it.

yart retlﬁ retaw eht ytpme ,woﬂrevo tneverp oTt

( 3 ) and dry around the ﬁlter case ( 2 ).

Insert the new ﬁlter into the ﬁlter case ( 3. 4 ).

Push the ﬁlter, and then turn it clockwise until it 4.

locks.

If you have trouble inserting the water t

ﬁlter because of high water pressure,

The locked symbol should be lined up t

with the indicator line.

Touch the 5. “

Ice Type/Water

Hold 3 sec for Filter Reset

”

button (

(Filter Reset)

) for

about 3 seconds to reset

the water ﬁlter. The color of

of the indicator ( ) changes from

6.

on.

For a replacement water ﬁlter, you can

visit your local home Improvement center

or contact the Samsung Parts distributor.

Be sure the replacement water ﬁlter has

the SAMSUNG logo on the box and

on the water ﬁlter. Link : http://www.

samsungparts.com

WARNING

(Red)

3

2

4

2

1

DA68-02601A(EN+FR+ES)-0.2.indb 13 2012.3.31 9:49:46 AM

02 OPERATING

18_

operating

Removing any residual matter inside

the water supply line after installing

the water ﬁlter.

Turn ON the main water 1.

supply and supply water

to the refrigerator.

Select water in the button

2.

“ICE TYPE/WATER”,pour

1 Gal (6-7 minutes) to clean the water supplier

system and it will take the air out from the lines.

possible an additional ﬂushing in the household

lines.

If after pour 1 Gal the water doesn’t turn clear is

3.

Open the Refrigerator door and make sure 4.

there are no water leaks coming from the

w

ater ﬁlter.

Be sure to ﬂush the dispenser system thoroughly,

otherwise water may drip from the dispenser.

This means that there is still air in the line.

Reverse Osmosis Water Supply

IMPORTANT:

The pressure of the water supply coming out of a

reverse osmosis system going to the water inlet

valve of the refrigerator needs to be between 35

and 120 psi (241 and 827 kPa).

If a reverse osmosis water ﬁltration system is

connected to your cold water supply, the water

pressure to the reverse osmosis system needs to

be a minimum of 40 to 60 psi (276 to 414 kPa.) If

the water pressure to the reverse osmosis system

is less than 40 to 60 psi (276 to 414 kPa):

Check to see whether the sediment ﬁlter in the t

reverse osmosis system is blocked. Replace

the ﬁlter if necessary.

Allow the storage tank on the reverse osmosis t

system to reﬁll after heavy usage.

If your refrigerator has a water ﬁlter, it may t

further reduce the water pressure when used

in conjunction with a reverse osmosis system.

Remove the water ﬁlter.

If you have questions about your water pressure,

call a licensed, qualiﬁed plumber.

CONTROLLING THE TEMPERATURE

Basic temperature of Freezer and

Refrigerator Compartments

The basic temperature and recommended

temperatures of the Freezer and Refrigerator

Compartments are 0°F and 37°F(or -18°C and

3°C) respectively. If the temperature of the Freezer

and Refrigerator Compartments are too high or

low, adjust the temperature manually.

Controlling the Freezer

temperature

The Freezer temperature can be set between -8°F

and 5°F (or between -23°C and -15°C) to suit

your particular needs. Press the Freezer button

repeatedly until the desired temperature is shown

in the temperature display. The temperature will

change by 1°F (or 1°C) with each press. See

below.

Fahrenheit : 0°F

-1°F -2°F -3°F -4°F

-5°F -6°F -7 °F -8°F 5°F 4°F 3°F

2°F 1°F 0°F.

Centigrade : -18°C -19°C -20°C -21°C

-22°C -23°C - 15°C -16°C -17°C

-18°C.

Keep in mind that foods like ice cream may melt

at 4°F (or -15.5°C). The temperature display will

move sequentially from -8°F to 5°F (or from -23°C

to -15°C).

Controlling the fridge temperature

The fridge temperature can be set between

34°F and 44°F (or between 1°C and 7°C) to suit

your particular needs. Press the Fridge button

repeatedly until the desired temperature is shown

in the temperature display. The temperature will

change by 1°F (or 1°C) with each press. See

below.

Fahrenheit : 37°F

36°F 35°F 34°F 44°F

43°F 42°F 41°F 40°F 39°F 38°F

37°F.

Centigrade : 3°C 2°C 1°C 7°C 6°C

5°C 4°C 3°C.

The temperature control process for the Fridge

works just like the Freezer process. Press the

Recommend Temp (Freezer) : 0°F (or -18°C )

DA68-02601A(EN+FR+ES)-0.2.indb 14 2012.3.31 9:49:47 AM

_19

operating

CAUTION

check the

water level

Test button

Fridge button to set your desired temperature.

After a few seconds, the Fridge will begin

adjusting towards the newly set temperature. This

will be reﬂected in the digital display.

The temperature of the Freezer, Fridge -

or Cool Select Pantry Zone may rise

when you open the doors too frequently,

or if a large amount of warm or hot food

is placed inside.

This may cause the digital display to blink. -

Once the Freezer and Fridge temperature

return to their normal set temperatures, the

blinking will stop.

If the blinking continues, you may need to -

“reset” the Refrigerator. Try unplugging the

appliance, wait for around 10 minutes and then

plug the power cord back in.

If there is a communication error between the -

Display and Main Controller, the Convertible

Display light may blink. If the blinking continues

for a long period of time, please contact a

Samsung Electronics Service Center.

USING THE COLD WATER

DISPENSER

Push the appropriate ice type

button to select what you want

dispensed.

Using the ice Dispenser

Maintaining the Ice Bucket

Place a glass underneath the ice

dispenser and push gently against the

dispenser lever with your glass.

Make sure the glass is in line with

the dispenser to prevent the ice from

bouncing out.

Please wait 2 seconds before removing the

glass under the dispenser to prevent spills.

If the Refrigerator door opens, the

Dispenser does not work.

When Cubed Ice is selected after using

the Crushed Ice mode, a small amount of

residual crushed ice might be produced.

Do not pull the lever out. You could damage

or break the lever’s spring.

To clean the ice bin/bucket, wash with a mild t

detergent, rinse well, and dry thoroughly it. Do

not use harsh or abrasive cleaners or solvents.

The ice cubes generated by the rapid ice t

making process will look white, which indicates

they are generated normally.

As the ice maker in the refrigerator room t

makes ice cubes even faster, move the ice

cubes from the refrigerator ice bin to the

freezer ice bin if you need more ice cubes.

If ice doesn’t come out, pull out the ice bucket t

and press the test button located on the right

side of ice maker.

Do not press the test button continuously t

when the tray is ﬁlled with ice or water. Water

may overﬂow or ice may jam the bucket.

Normal Use

t

To ﬁll the ice bucket to maximum capacity after

installation, follow these steps:

Water may overﬂow or ice may jam the bucket.

NO ICE

Select this if you want to

Recommend Temp (Fridge) : 37°F (or 3°C )

DA68-02601A(EN+FR+ES)-0.2.indb 15 2012.3.31 9:49:48 AM

02 OPERATING

20_

operating

remove all ice cube tray. If not using the ice

dispenser, it is possible to stack the cubes.

Remove the tank in the direction of the arrow.

Dispose of ice cubes or ice mass. Push the bottom

of the tray until it clicks.

and try again.

Use only the ice maker refrigerator. Only a suitably

supply to the refrigerator. Connect only to a

potable water supply.

In order that the ice maker work properly, need a

water pressure of 20 ~ 125 psi (138 ~ 862 kPa).

Whether traveling for vacation or business and

will not use water dispensers and ice for an

extended period:

Close the stopcock. If not, can result in water

leakage.

Remove all food.

Unplug the refrigerator.

Remove excess moisture from inside the

refrigerator and leave doors open. Otherwise,

hands or any other inappropriate object in the

container or bucket of ice maker.

It may cause personal injury or property damage.

Can cause injury.

Never try to take the ice maker.

Do not wipe or spray the ice tray with water while

in the refrigerator. Remove for cleaning.

-

When inserting the tray of the ice maker,

make sure it is well centrada.De Otherwise,

you could lock.

The phenomenon of turbidity

The water entering the cooler circulates through

oxygen and nitrogen. When it is contacted with air,

the pressure drops rapidly and the oxygen and

nitrogen is oversaturated and generate gas bubbles.

Temporarily, water can have a cloudy appearance

due to these bubbles of oxygen. After a few seconds,

water is colorless.

To remove the ice cubes without use the

(Remove the front cover of the Ice Maker)

Ice cubes in the ice machine may leak on

the drawer.

Not put food into the tray of ice.de hielo.

If you store food in the ice bucket,may hinder the

ice maker to open or close the door, and damage

the ice maker.

Note that the ice cubes from the ice bucket

can spill over the box to remove the tray from

the drawer. In this case, you must remove the

drawer the ice cubes that have been spilled.

In case of power outage, ice cubes can melt

and then freeze when power returns, causing

the dispenser to stop working.

To prevent this from happening after a power outage,

remove the ice bucket and discard the ice and

wastewater.

If you use all the ice at one time, repeat

Steps 2 and 3 on the previous page.

may have bad taste.

However, wait only 8 hours before removing the

cubes and ensure their maximum output.

How to Use Ice O function

WARNNIG

DA68-02601A(EN+FR+ES)-0.2.indb 16 2012.3.31 9:50:26 AM

WARNNIG

check the

water level

Test button

La page charge ...

Samsung RF263BEAESG Mode d'emploi

Samsung RF263BEAESG Mode d'emploi

dans d''autres langues

Documents connexes