Wacker Neuson E2200 Manuel utilisateur

Operator’s Manual

Notice d'emploi

Hydronic Surface Heater

Réchauffeur hydronique de surface

E2200

E3000ES

Type E2200, E3000ES

Document 5100024640

Date

0118

Version 03

Language EN-FR

5100024640

Copyright notice

All rights, including copying and distribution rights, are reserved.

This publication may be photocopied by the original purchaser of the

machine. Any other type of reproduction is prohibited without express

written permission from Wacker Neuson Production Americas LLC.

Any type of reproduction or distribution not authorized by Wacker

Neuson Production Americas LLC represents an infringement of valid

copyrights. Violators will be prosecuted.

Trademarks

All trademarks referenced in this manual are the property of their

respective owners.

Manufacturer

Wacker Neuson Production Americas LLC

N92W15000 Anthony Avenue

Menomonee Falls, WI 53051 U.S.A.

Tel: (262) 255-0500 · Fax: (262) 255-0550 · Tel: (800) 770-0957

www.wackerneuson.com

Original instructions

This Operator’s Manual presents the original instructions. The original

language of this Operator’s Manual is American English.

E2200 / E3000ES Foreword

wc_tx004248gb_FM10.fm 3

Foreword

This heater is designed and approved for use as a construction heater in

accordance with the applicable standards of CSA. CHECK WITH YOUR LOCAL

FIRE SAFETY AUTHORITY IF YOU HAVE QUESTIONS ABOUT APPLICATIONS.

Other standards govern the use of fuel gases and heat producing products in

specific applications. Your local authority can advise you about these.

THE INSTALLATION OF THE UNIT SHALL BE IN ACCORDANCE WITH THE

REGULATIONS OF THE AUTHORITIES HAVING JURISDICTION.

Machines

covered by

this manual

This manual covers machines with the following item numbers:

Machine

identification

A nameplate listing the model number, item number, revision number, and serial

number is attached to this machine. The location of the nameplate is shown above.

Serial number

(S/N)

For future reference, record the serial number in the space provided below. You will

need the serial number when requesting parts or service for this machine.

Machine Item Number Revision

E2200 5000620176 105 and above

E2200 5000620215 105 and above

E2200G 5100017448 100 and above

E2200G 5100017449 100 and above

E3000ES 5000620967 100 and above

E3000ES-G 5100017801 100 and above

wc_gr012120

Serial Number:

Foreword E2200 / E3000ES

4 wc_tx004248gb_FM10.fm

Machine

documentation

 From this point forward in this documentation, Wacker Neuson Production

Americas

LLC will be referred to as Wacker Neuson.

 Keep a copy of the Operator’s Manual with the machine at all times.

 Use the separate Parts Book supplied with the machine to order replacement

parts.

 If you are missing any of these documents, please contact Wacker Neuson to

order a

replacement or visit www

.wackerneuson.com.

 When ordering parts or requesting service information, be prepared to provide

the machine model number

, item number, revision number, and serial number.

Expectations

for

information in

this manual

 This manual provides information and procedures to safely operate and

maintain the above Wacker Neuson model(s). For your own safety and to

reduce the risk of injury, carefully read, understand, and obser

ve all instructions

describe

d in this manu

al.

 Wacker Neuson expressly reserves the right to make technical modifications,

even

without notice, which improve the performance or safety standards of it

s

mac

hines.

 The information contained in this manual is based on machines manufactured

up until the time of publication. Wacker Neuson reserves the right to change

any p

ortion of this information without notice.

Manufacturer’s

approval

This manual contains references to approved parts, attachments, and

modifications. The following definitions apply:

 Approved parts or attachments are those either manufactured or provided by

Wacker Neuson.

 Approved modifications are those performed by an authorized Wacker

Neu

son service center according to written instructions published by Wacker

Neuson.

 Unapproved parts, attachments, and modifications are those that do not

meet the approved criteria.

Unapproved parts, attachments, or modifications may have the following

consequences:

 Serious injury hazards to the operator and persons in the work area

 Permanent damage to the machine which will not be covered under warranty

Contact your Wacker Neuson dealer immediately if you have questions about

approved or unapproved parts, attachments, or modifications.

wc_bo5100024598_03_FM10TOC.fm

5

Table of Contents

E2200 / E3000ES

Foreword 3

1

Safety Information 9

1.1 Signal Words Used in this Manual ....................................................... 9

1.2 Machine Description and Intended Use ............................................. 10

1.3 Safety Guidelines for Operating the Machine ..................................... 11

1.4 Service Safety .................................................................................... 13

1.5 Safety Guidelines for Operating Combustion Burners ....................... 15

1.6 Safety Guidelines for Operating Generators ...................................... 16

1.7 Safety Guidelines for Towing the Machine ......................................... 18

1.8 Safety Guidelines for Lifting the Machine ........................................... 19

1.9 Reporting Safety Defects ................................................................... 19

2 Labels 20

2.1 Label Locations .................................................................................. 20

2.2 Label Meanings .................................................................................. 23

3 Lifting and Transporting 31

3.1 Lifting the Machine ............................................................................. 31

3.2 Hazardous Materials Placards ........................................................... 32

3.3 Preparing the Machine for Transport on a Truck or Trailer ................ 33

3.4 Transporting the Machine on a Truck or Trailer ................................. 34

3.5 Before Towing Checklist ..................................................................... 35

3.6 Towing the Machine ........................................................................... 36

3.7 Testing the Breakaway System—Electric Brakes .............................. 37

4 Operation 39

4.1 Control and Component Locations ..................................................... 39

4.2 Control and Component Descriptions ................................................ 40

4.3 Control Panel ...................................................................................... 41

4.4 Control Panel Components ................................................................ 42

4.5 Rear Components .............................................................................. 43

4.6 Pumps, Gauges, and Valves .............................................................. 44

4.7 Preparing the Machine for First Use ................................................... 45

4.8 Breaking in the Generator .................................................................. 45

4.9 General Sequence of Operation ......................................................... 46

4.10 Checking the HTF Level ..................................................................... 47

4.11 Recommended Fuels and Fuel Blending Guide ................................. 48

6

wc_bo5100024598_03_FM10TOC.fm

Table of ContentsE2200 / E3000ES

4.12 Refueling the Machine .........................................................................49

4.13 Positioning the Machine ......................................................................50

4.14 Before Starting Checks .......................................................................51

4.15 Starting, Operating, and Stopping—Machines with Generators ..........54

4.16 Starting, Operating, and Stopping—Machines without Generators .....59

4.17 Preheating the HTF .............................................................................62

4.18 Initiating HTF Flow ..............................................................................63

4.19 Setting the Operating Temperature .....................................................65

4.20 Positioning the Hoses and Operating the Machine .............................66

4.21 Monitoring the Operating Parameters .................................................69

4.22 Rewinding the Hoses ..........................................................................70

4.23 Resetting a Low HTF Level Fault ........................................................72

4.24 Quick-Connect Coupling Usage and Care ..........................................75

4.25 Resetting the Snap Switch ..................................................................76

4.26 Operating States of the Beckett Burner Controller ..............................77

5 Accessories 81

5.1 Available Accessories .........................................................................81

5.2 Connecting the HX200 or HX60 Heat Exchanger ...............................82

5.3 Connecting the HX100 or HX30 Heat Exchanger ...............................84

5.4 Connecting the HX50 or HX15 Heat Exchanger .................................86

5.5 Combining the Machine with One HHS and One DPP ........................88

5.6 Combining the Machine with Two HHS and Two DPP (E2200 only) ..90

5.7 Mounting the Auxiliary Pump Panel ....................................................92

6 Burner Setup 93

6.1 Setting and Checking the Electrodes ..................................................96

6.2 Checking and Replacing the Burner Nozzle ........................................98

6.3 Setting the “Z” Distance on V1-Style Heads ......................................100

6.4 Adjusting the Air Settings ..................................................................102

6.5 Setting the Fuel Pressure ..................................................................103

7 Maintenance 104

7.1 Periodic Maintenance Schedule ........................................................104

7.2 Repairing a Hose ...............................................................................105

7.3 Inspecting the HTF System and the Fuel System .............................107

7.4 Inspecting Electrical Cords ................................................................108

7.5 Filling the HTF Reservoir ...................................................................109

7.6 Cleaning the HTF Strainer .................................................................112

wc_bo5100024598_03_FM10TOC.fm

7

Table of Contents

E2200 / E3000ES

7.7 Replacing the Fuel Filter .................................................................. 114

7.8 Lubricating the Hose Reel System ................................................... 115

7.9 Cleaning the Turbulators and the Exhaust Ducting .......................... 116

7.10 Inspecting and Replacing the Rope Gasket ..................................... 118

7.11 Removing the Burner ....................................................................... 119

7.12 Installing the Burner ......................................................................... 120

7.13 Storing the Machine ......................................................................... 121

7.14 Preparing the Machine for Seasonal Operation ............................... 122

7.15 Storing the Generator ....................................................................... 123

7.16 Connecting and Maintaining the Battery .......................................... 124

8 Generator Maintenance 125

8.1 Generator Load Banking Procedure ................................................. 127

9 Troubleshooting 129

9.1 Troubleshooting the Machine ........................................................... 129

10 Technical Data 132

10.1 E2200 ............................................................................................... 132

10.2 E3000ES .......................................................................................... 133

10.3 Trailer ............................................................................................... 134

10.4 Dimensions ....................................................................................... 134

MSDS: Dowfrost HD 50 135

Fuji Temperature Controller 143

Tire Safety Information 147

11 Schematics 159

11.1 Electrical Schematic ......................................................................... 159

11.2 Electrical Schematic Components .................................................... 160

11.3 Burner System Circuit ...................................................................... 163

11.4 Circulation System Circuit ................................................................ 164

11.5 Rewind System Circuit ..................................................................... 165

11.6 Generator—AC Schematic ............................................................... 166

11.7 Generator—AC Schematic Components ......................................... 167

8

wc_bo5100024598_03_FM10TOC.fm

Table of ContentsE2200 / E3000ES

11.8 Generator—DC Schematic ................................................................168

11.9 Generator—DC Schematic Components ..........................................169

11.10 Trailer Wiring .....................................................................................170

11.11 Trailer Plug—Wiring Diagram ............................................................171

11.12 Trailer Junction Box—Wiring Diagram ..............................................172

wc_si000540gb_FM10.fm

9

E2200 / E3000ES Safety Information

1 Safety Information

1.1 Signal Words Used in this Manual

This manual contains DANGER, WARNING, CAUTION, NOTICE, and NOTE

signal words which must be followed to reduce the possibility of personal injury,

damage to the equipment, or improper service.

NOTICE: Used without the safety alert symbol, NOTICE indicates a situation

which, if not avoided, could result in property damage.

Note: A Note contains additional information important to a procedure.

This is the safety alert symbol. It is used to alert you to potential personal hazards.

► Obey all safety messages that follow this symbol.

DANGER

DANGER indicates a hazardous situation which, if not avoided, will result in death

or serious injury.

► To avoid death or serious injury from this type of hazard, obe

y all safety

messages that follow this signal word.

WARNING

WARNING indicates a hazardous situation which, if not avoided, could result in

death or serious injury.

► To avoid possible death or serious injury from this type of hazard,

obey all safety

messages that follow this signal word.

CAUTION

CAUTION indicates a hazardous situation which, if not avoided, could result in

minor or moderate injury.

► To avoid possible minor or moderate injury from this type of hazard,

obey all

safety messages that follow this signal word.

wc_si000540gb_FM10.fm

10

Safety Information E2200 / E3000ES

1.2 Machine Description and Intended Use

This machine is a hydronic surface heater. The Wacker Neuson Hydronic Surface

Heaters consist of a trailer-mounted enclosure that houses an optional diesel

generator, a hydronic heater, electric motors, fixed pump(s) and plumbing, a diesel

(or gas) burner, a fuel tank, and a hose handling system.

The hydronic heating system utilizes a burner that indirectly warms the Heat

Transfer Fluid (HTF). The warmed HTF is continuously circulated through a

vented, closed loop hose system. A positive displacement pump pushes the

warmed HTF through the hose system, thereby radiating and transferring the heat

to the required application area.

An insulated blanket may be laid over the hoses to increase efficiency. The low

HTF level protection device shuts down the machine if the HTF level drops below

minimum operational capacity.

This machine is intended to be used as a surface heater in order to thaw frozen

ground, to cure concrete, or to prevent frost and freezing. In addition, when used

with other Wacker Neuson accessories, this machine can be used to heat air.

This machine has been designed and built strictly for the intended use(s) described

above. Using the machine for any other purpose could permanently damage the

machine or seriously injure the operator or other persons in the area. Machine

damage caused by misuse is not covered under warranty.

The following are some examples of misuse:

■ Using the machine to heat anything other than what is stated above

■ Using the machine to pump anything other than the factory recommended Heat

Transfer Fluid

■ Using the generator (if equipped) to power anything other than the machine

itself or Wacker Neuson accessory machines, as instructed in the Operator's

Manual

■ Using the machine as a ladder, support, or work surface

■ Using the machine to carry or transport passengers or equipment

■ Using the machine to tow other machines

■ Operating the generator (if equipped) in a manner that is inconsistent with all

federal, state, and local codes and regulations

■ Operating the machine outside of factory specifications

■ Operating the machine in a manner inconsistent with all warnings found on the

machine and in the Operator’s Manual

This machine has been designed and built in accordance with the latest global

safety standards. It has been carefully engineered to eliminate hazards as far as

practicable and to increase operator safety through protective guards and labeling.

However, some risks may remain even after protective measures have been taken.

They are called residual risks. On this machine, they may include exposure to:

■ Heat, noise, and exhaust from the engine or hydronic heater

■ Burns from the HTF or radiant heat from the hoses

wc_si000540gb_FM10.fm

11

E2200 / E3000ES Safety Information

■ Fire hazards from improper refueling techniques

■ Fuel and its fumes

■ Personal injury from improper lifting of the trailer tongue

■ Tripping hazards from the hoses

To protect yourself and others, make sure you thoroughly read and understand the

safety information presented in this manual before operating the machine.

1.3 Safety Guidelines for Operating the Machine

Operator

training

Before operating the machine:

■ Read and understand the operating instructions contained in all manuals

delivered with the machine.

■ Familiarize yourself with the location and proper use of all controls and safety

devices.

■ Contact Wacker Neuson for additional training if necessary.

When operating this machine:

■ Do not allow improperly trained people to operate the machine. People

operating the machine must be familiar with the potential risks and hazards

associated with it.

Operator

qualifications

Only trained personnel are permitted to start, operate, and shut down the machine.

They also must meet the following qualifications:

■ Have received instruction on how to properly use the machine

■ Are familiar with required safety devices

The machine must not be accessed or operated by:

■ Children

■ People impaired by alcohol, drugs or prescription drugs

Application

area

Be aware of the application area.

■ Keep unauthorized personnel, children, and pets away from the machine.

■ Remain aware of changing positions and the movement of other equipment and

personnel in the application area/job site.

■ Identify whether special hazards exist in the application area, such as toxic

gases or unstable ground conditions, and take appropriate action to eliminate

the special hazards before using the machine.

Be aware of the application area.

■ Do not operate the machine in areas that contain flammable objects, fuels, or

products that produce flammable vapors.

Safety

devices,

controls, and

attachments

Only operate the machine when:

■ All safety devices and guards are in place and in working order.

■ All controls operate correctly.

■ The machine is set up correctly according to the instructions in the Operator’s

Manual.

wc_si000540gb_FM10.fm

12

Safety Information E2200 / E3000ES

■ The machine is clean.

■ The machine’s labels are legible.

To ensure safe operation of the machine:

■ Do not operate the machine if any safety devices or guards are missing or

inoperative.

■ Do not modify or defeat the safety devices.

■ Only use accessories or attachments that are approved by Wacker Neuson.

Safe

operating

practices

When operating this machine:

■ Remain aware of the machine’s moving parts. Keep hands, feet, and loose

clothing away from the machine’s moving parts.

When operating this machine:

■ Do not operate a machine in need of repair.

Personal

Protective

Equipment

(PPE)

Wear the following Personal Protective Equipment (PPE) while operating this

machine:

■ Close-fitting work clothes that do not hinder movement

■ Safety glasses with side shields

■ Hearing protection

■ Safety-toed footwear

wc_si000540gb_FM10.fm

13

E2200 / E3000ES Safety Information

1.4 Service Safety

Service

training

Before servicing or maintaining the machine:

■ Read and understand the instructions contained in all manuals delivered with

the machine.

■ Familiarize yourself with the location and proper use of all controls and

protective devices.

■ Only trained personnel shall troubleshoot or repair problems occurring with the

machine.

■ Contact Wacker Neuson for additional training if necessary.

When servicing or maintaining this machine:

■ Do not allow untrained or improperly trained people to service or maintain the

machine. Personnel servicing or maintaining the machine must be familiar with

the associated potential risks and hazards.

■ Maintenance items that can be performed by the operator are listed in this

manual. Other repairs should be performed by a qualified technician. Repairs

can be hazardous if not performed correctly. Contact your Wacker Neuson

dealer service department for additional information or for repairs to your

machine.

Precautions

When servicing or maintaining the machine:

■ Read and understand the service procedures before performing any service to

the machine.

■ All adjustments and repairs must be completed before operating the machine.

Do not operate the machine with a known problem or deficiency.

■ All repairs and adjustments shall be completed by a qualified technician.

■ Turn off the machine before performing maintenance or making repairs.

■ Remain aware of the machine’s moving parts. Keep hands, feet, and loose

clothing away from the machine’s moving parts.

■ Re-install the safety devices and guards after repair and maintenance

procedures are complete.

Machine

modifications

When servicing or maintaining the machine:

■ Use only accessories/attachments that are approved by Wacker Neuson.

■ Do not defeat safety devices.

■ Do not modify the machine without the express written approval of Wacker

Neuson.

Replacing

parts and

labels

■ Replace worn or damaged components.

■ Replace all missing and hard-to-read labels.

■ When replacing electrical components, use components that are identical in

rating and performance to the original components.

■ When replacement parts are required for this machine, use only Wacker

Neuson replacement parts or those parts equivalent to the original in all types of

specifications, such as physical dimensions, type, strength, and material.

wc_si000540gb_FM10.fm

14

Safety Information E2200 / E3000ES

Cleaning

When cleaning and servicing the machine:

■ Keep machine clean and free of debris such as leaves, paper, cartons, etc.

■ Keep labels legible.

■ Clean with soapy water only.

When cleaning the machine:

■ Do not clean the machine while it is running.

■ Never use gasoline or other types of fuels or flammable solvents to clean the

machine. Fumes from fuels and solvents can become explosive.

Personal

Protective

Equipment

(PPE)

Wear the following Personal Protective Equipment (PPE) while servicing or

maintaining this machine:

■ Close-fitting work clothes that do not hinder movement

■ Safety glasses with side shields

■ Hearing protection

■ Safety-toed footwear

In addition, before servicing or maintaining the machine:

■ Tie back long hair.

■ Remove all jewelry (including rings).

Maintenance

guidelines

When maintaining the machine:

■ Keep the fuel lines in good condition and properly connected.

■ Allow the burner to cool before servicing the machine.

■ Allow the Heat Transfer Fluid (HTF) to cool before maintaining the machine.

■ Keep all electrical cords away from heat, oil, vibrating surfaces, and sharp

edges.

wc_si000540gb_FM10.fm

15

E2200 / E3000ES Safety Information

1.5 Safety Guidelines for Operating Combustion Burners

When using the machine:

■ Make sure you have proper certification or licensing required by the locality,

state, or province in which the machine is being installed to connect natural gas

or LP.

■ Clean up any spilled fuel immediately.

■ Replace the fuel tank cap after refueling the machine.

■ Refill the fuel tank in a well-ventilated area.

■ Always keep the oil supply valve shut off if the burner is shut down for an

extended period of time.

When using the machine:

■ Do not fill or drain the fuel tank near an open flame, while smoking, or while the

machine is running.

■ Do not smoke when refueling the machine.

■ Do not smoke when connecting natural gas or LP.

■ Do not attempt to start the burner when excess oil has accumulated, when the

unit is full of vapors, or when the combustion chamber is very hot.

Note: Some machines may not be capable of supporting natural gas or LP. Please

see the burner manufacturer’s literature for more information.

DANGER

Carbon monoxide. Using this machine indoors CAN KILL YOU IN MINUTES.

Exhaust gas contains carbon monoxide (CO). This is a deadly poison you cannot

see or smell. If you can smell the exhaust, you are breathing CO. Even if you

cannot smell the exhaust, you could be breathing CO.

► NEVER operate the machine inside an enclosed area, such as a home, tunnel,

or garage unless it is vented properly.

► ONLY use the machine outside and far away from windows, doors, and vents.

These openings can pull in exhaust gas.

► ALWAYS use a battery-powered or battery-backup CO alarm in nearby

structures. Even when you use the machine correctly, CO may leak into nearby

structures.

► If you start to feel sick, dizzy, or weak after the machine has been running, move

to fresh air IMMEDIATELY. See a doctor. You could have carbon monoxide

poisoning.

wc_si000540gb_FM10.fm

16

Safety Information E2200 / E3000ES

1.6 Safety Guidelines for Operating Generators

This machine is built with user safety in mind; however, like any electrical device it

can present serious hazards if improperly operated and serviced. Follow

instructions carefully. Should questions arise during operation or service of this

equipment, contact your Wacker Neuson dealer.

General

precautions

■ Keep a multi-class, type ABC or equivalent fire extinguisher at hand when using

the generator. Refer to NFPA No. 10 for further information regarding fire

extinguishers.

■ Do not use evaporative starting fluids. They are highly explosive.

■ Do not store items such as excess oil, oil rags, or tools within the generator

compartment. Items stored within the generator compartment are a fire hazard

and can restrict cooling air.

Before

operating the

generator

■ Know how to start, operate, and stop the generator before starting it.

■ Obtain the proper training for operating the generator. Do not allow untrained

personnel to operate or service the generator.

■ Check the fuel lines and the fuel tank for leaks and cracks before starting the

engine.

■ Clean the generator of any spilled fuel.

DANGER

Carbon monoxide. Using a generator indoors CAN KILL YOU IN MINUTES.

Generator exhaust contains carbon monoxide (CO). This is a poison you cannot

see or smell. If you can smell the generator exhaust, you are breathing CO. But

even if you cannot smell the exhaust, you could be breathing CO.

WARNING

Electrocution hazard. Generators present special hazards during operation and

servicing. These include the risk of electrocution or severe electrical shock. Failure

to follow the safety information below can result in severe injury or death.

► Read and follow the safety instructions in this Operator’s Manual.

► Contact the generator manufacturer for additional information regarding the

generator.

WARNING

Internal combustion engines present special hazards during operation and fueling.

Failure to follow the warnings and safety instructions could result in severe injury or

death.

► Read and follow the safety instructions in this Operator’s Manual.

► Contact the generator manufacturer for additional information regarding the

generator.

wc_si000540gb_FM10.fm

17

E2200 / E3000ES Safety Information

Running the

generator

■ Do not start the engine if fuel has spilled or a fuel odor is present.

■ Keep the area around the exhaust pipe free of flammable materials.

■ Do not smoke while operating the generator.

■ Keep sparks, flames, electrical arcs, and other sources of ignition far away from

the generator.

■ Do not touch the engine or muffler while the engine is running or immediately

after it has been turned off.

■ Do not overload the generator. The total amperage of the tools and equipment

attached to the generator must not exceed the load rating of the generator.

■ Do not operate the generator with wet hands.

■ Do not remove the radiator cap when the generator is running or hot.

Refueling

safety

When adding fuel to the fuel tank:

■ Do not smoke.

■ Do not refuel a hot or running engine.

When adding fuel to the fuel tank:

■ Keep sparks, flames, electrical arcs, and other sources of ignition far away from

the generator.

■ Refill the fuel tank only in a well-ventilated area.

■ Re-install the fuel tank cap after refueling.

Maintenance

safety

■ Only a trained technician should attempt to repair the generator.

■ Test procedures which require that the generator be running must be performed

using extreme caution.

■ Make sure clothing and shoes are dry, stand on a dry wooden platform or rubber

insulating mat, and use tools with insulated handles when servicing the

generator.

■ Engine antifreeze is toxic to humans and animals. Clean up spills and dispose

of used engine antifreeze in accordance with local environmental regulations.

■ Make sure all fasteners are secure and torqued properly.

wc_si000540gb_FM10.fm

18

Safety Information E2200 / E3000ES

1.7 Safety Guidelines for Towing the Machine

When towing the machine:

■ Do not tow the machine if the towing vehicle’s hitch or the trailer’s coupler are

damaged.

■ Do not tow the machine if safety chains are damaged.

■ Do not tow the machine if any of the trailer’s lug nuts are loose or missing.

■ Do not tow the machine if the trailer’s tires have less than 1/16 inch (1.5 mm) of

tread.

■ Do not tow the machine if trailer tires are underinflated.

■ Do not tow the machine unless the trailer’s brakes are functioning properly.

■ Do not tow the machine if trailer lighting is not functioning properly.

■ Do not exceed the trailer manufacturer’s speed limitations of 89 km/h (55 mph).

When towing the machine:

■ Only tow the machine when the trailer’s lug nuts are properly torqued.

■ Only tow the machine when the trailer’s tires are properly inflated.

■ Only tow the machine when all trailer lights are functioning correctly.

■ Only tow the machine when the trailer’s safety chains are connected to the

towing vehicle in a crisscross pattern.

■ Maintain extra distance between the towing vehicle and other vehicles.

■ Avoid soft shoulders, curbs, and sudden lane changes.

■ Abide by all licensing requirements for your area.

If you have not driven a towing vehicle with a trailer before, practice turning,

stopping, and backing up the towing vehicle with the trailer in an area away from

traffic. Only drive the towing vehicle with the trailer when you are confident in your

ability to do so.

WARNING

Risk of severe injury or death. Improper trailer condition and towing technique can

lead to an accident.

► Obey the instructions below to reduce the risk of an accident.

wc_si000540gb_FM10.fm

19

E2200 / E3000ES Safety Information

1.8 Safety Guidelines for Lifting the Machine

When lifting the machine:

■ Make sure slings, chains, hooks, ramps, jacks, forklifts, cranes, hoists, and any

other type of lifting device used is attached securely and has enough weight-

bearing capacity to lift or hold the machine safely. See chapter Technical Data

for machine weight.

■ Remain aware of the location of other people when lifting the machine.

■ Only use the lifting points and tie-downs described in the Operator’s Manual.

■ Make sure the transporting vehicle has sufficient load capacity and platform size

to safely transport the machine.

To reduce the possibility of injury:

■ Do not stand under the machine while it is being lifted or moved.

■ Do not get onto the machine while it is being lifted or moved.

1.9 Reporting Safety Defects

If you believe your trailer has a defect which could cause a crash or could cause

injury or death, you should immediately inform the National Highway Traffic Safety

Administration (NHTSA) in addition to notifying Wacker Neuson.

If NHTSA receives similar complaints, it may open an investigation; and if it finds

that a safety defect exists in a group of trailers, it may order a recall and remedy

campaign. However, NHTSA cannot become involved in individual problems

between you, your dealer, or Wacker Neuson.

To contact NHTSA, you may either contact the Vehicle Safety Hotline toll-free at

1-888-327-4236 (TTY: 1-800-424-9153); go to http://www.safercar.gov; or write to:

Administrator

NHTSA

1200 New Jersey Avenue S.E.

Washington, DC 20590

You can also obtain other information about your motor vehicle safety from

http://www.safercar.gov

wc_si000985gb_FM10.fm

20

Labels E2200 / E3000ES

2 Labels

2.1 Label Locations

wc_gr012117a

624

642

640

620

625

510

624

643

648

647

626

641

602

643

604

640

La page est en cours de chargement...

Wacker Neuson E2200 Manuel utilisateur

Ce manuel convient également à

Wacker Neuson E2200 Manuel utilisateur

dans d''autres langues

Documents connexes