Peerless ESA763PU Guide d'installation

ISSUED: 01-05-11 SHEET #: 061-9062-7 03-22-12

Models: ESA763PU

Installation and Assembly:

Corrosion Resistant Articulating Mount for Indoor or Outdoor

37" - 63" Flat Panel Displays

2300 White Oak Circle • Aurora, Il 60502 • (800) 865-2112 • Fax: (800) 359-6500 • www.peerless-av.com

Max UL Load Capacity: 200 lb (90.7 kg)

2 of 50 ISSUED: 01-05-11 SHEET #: 061-9062-7 03-22-12

Note: Read entire instruction sheet before you start installation and assembly.

Table of Contents

Parts List.............................................................................................................................................................................3, 4

Wall installation ...................................................................................................................................................................6, 7

Installing Adapter Brackets to Display ...............................................................................................................................8-13

Mounting Flat Panel Display .................................................................................................................................................14

Cable Management ..............................................................................................................................................................16

Tools Needed for Assembly

• stud ﬁ nder ("edge to edge" stud ﬁ nder is recommended)

• phillips screwdriver

• drill

• 3/16" (5mm) drill bits for wood studs, 13/32" (10mm) drill bits for concrete

• level

• Do not begin to install your Peerless product until you have read and understood the instructions and warnings

contained in this Installation Sheet. If you have any questions regarding any of the instructions or warnings, for US

customers please call Peerless customer care at 1-800-865-2112, for all international customers, please contact

your local distributor.

• This product should only be installed by someone of good mechanical aptitude, has experience with basic building

construction, and fully understands these instructions.

• Due to outdoor environmental conditions such as heavy snow, hail, rain, etc. the environmental mount and

hardware must be inspected at least once a year. This product should not be exposed to high winds. A qualiﬁ ed

installer or inspector must check for signs of rust, loose fasteners, bent metal, etc. If evidence of excessive wear,

deterioration or any unsafe condition is observed, this product must be taken out of service immediately. Direct all

inquiries to customer care if you have any questions.

• Make sure that the supporting surface will safely support the combined load of the equipment and all attached

hardware and components.

• Never exceed the Maximum UL Load Capacity. See page one.

• If mounting to wood wall studs, make sure that mounting screws are anchored into the center of the studs. Use of

an "edge to edge" stud ﬁ nder is highly recommended.

• Always use an assistant or mechanical lifting equipment to safely lift and position equipment.

• Tighten screws ﬁ rmly, but do not overtighten. Overtightening can damage the items, greatly reducing their holding

power.

• This product was designed to be installed on the following wall construction only;

WALL CONSTRUCTION HARDWARE REQUIRED

• Wood Stud Included

• Wood Beam Included

• Solid Concrete Included

• Cinder Block Included

•Metal Stud Contact Qualiﬁ ed Professional (not evaluated by UL)

•Brick Contact Qualiﬁ ed Professional (not evaluated by UL)

•Other or unsure? Contact Qualiﬁ ed Professional

WARNING

3 of 50 ISSUED: 01-05-11 SHEET #: 061-9062-7 03-22-12

ESA763PU

Description Qty. Part #

A

wall arm assembly 1 095-T1994

Buniversal adapter bracket 1 095-T1635-2

C3" wood screw 3 520-D1243

D10mm concrete anchor 4 590-0321

EM10 x 15mm socket head screw 2520-D1262

Fwall plate cover 2590-1325

Gcable ties 16 590-1168

H6mm allen wrench 1 560-9716

I5mm allen wrench 1 560-9640

Jrear cable cover 4 590-P1326

K

front cable cover 4 590-P1327

L5/32" allen wrench 1 560-9646

M2.5" security wood screw 1 520-D1668

Parts List

BCD

EG

M

H

J

L

F

K

I

A

Parts may appear slightly different than illustrated.

Before you begin, make sure all parts shown are included with your product.

4 of 50 ISSUED: 01-05-11 SHEET #: 061-9062-7 03-22-12

Adapter Bracket Fasteners

M4 x 12 mm (6)

(510-D1079)

M4 x 25 mm (4)

(510-D1082)

M5 x 12 mm (4)

(520-D1064) M5 x 25 mm (4)

(520-D1122)

M8 x 12 mm (6)

(520-D1068)

M8 x 40 mm (4)

(520-D1152)

M8 x 25 mm (4)

(520-D1101)

I.D. .34" (4)

(540-1059)

I.D. .22" (4)

(540-1057)

M6 x 30 mm (4)

(520-D1067)

M6 x 12 mm (4)

(520-D1050)

M6 x 25 mm (4)

(520-D1211)

M6 x 20 mm (4)

(520-D1554)

multi-washer (6)

(580-D1036)

5 of 50 ISSUED: 01-05-11 SHEET #: 061-9062-7 03-22-12

1/4-20 X 17 MM SCREWS WALL PLATE

WALL ARM

SLIDE PLATE

WALL PLATE RAIL

NOTE: If mounting wall arm (A) to wood stud walls, slots on wall plate must align to wood studs.

Determine desired location of display center detailed in step 2.

Measure the distance from the center of wall arm (A) to desired display center. Loosen four 1/4-20 x 17mm screws

using 5mm allen wrench (I). Slide wall arm assembly 4-1/2" to the left or right as shown in ﬁ gure 1.1. NOTE: Align

bevels (dots) of slide plate with bevels (dots) of wall plate rails as shown in detail 1 then retighten 1/4-20 x 17mm

screws.

Do not adjust arm while display is attached.

Skip to page 6 for Wood Stud Installation.

Skip to page 7 for Concrete and Cinder Block Installation.

1

Optional Horizontal Adjustment of Wall Arm on Wall Plate

ﬁ g. 1.1

DETAIL 1

6 of 50 ISSUED: 01-05-11 SHEET #: 061-9062-7 03-22-12

9"

(229 mm)

Use a stud ﬁ nder to locate the edges of the studs and draw a vertical line down the center of each stud. Determine

and mark the desired display center on the wall. Place wall plate template (wall arm) on wall with top mounting slots

9" (229mm) above desired display center as shown in ﬁ gure 2.1. Level wall plate template (wall arm) on wall and

mark center of four mounting holes making sure that the mounting holes are on the stud centerlines. Drill four 3/16"

(5mm) dia. pilot holes to a depth of 3" (76mm). Attach wall arm (A) to wall using three wood screws (C) and one

security wood screw (M) as shown in ﬁ g. 2.2.

Level wall plate then tighten all fasteners.

Installation to Double-Stud Wall

2

• Installer must verify that the supporting surface will safely support the combined load of the equipment and all

attached hardware and components.

• Tighten wood screws so that wall plate is ﬁ rmly attached, but do not overtighten. Overtightening can damage the

screws, greatly reducing their holding power.

• Never tighten in excess of 80 in. • lb (9 N.M.).

• Make sure that mounting screws are anchored into the center of the stud. The use of an "edge to edge" stud ﬁ nder

is highly recommended.

• Hardware provided is for attachment of mount through standard thickness drywall or plaster into wood studs.

Installers are responsible to provide hardware for other types of mounting situations (not evaluated by UL).

WARNING

A

WOOD STUD

ﬁ g. 2.2

CS = CENTER OF DISPLAY

ﬁ g. 2.1

CS

M

C

#14 SECURITY

SCREW

5/16" WOOD

SCREW

7 of 50 ISSUED: 01-05-11 SHEET #: 061-9062-7 03-22-12

Installation to Solid Concrete or Cinder Block

Determine and mark the desired display center on the

wall. Place wall plate template (wall arm) on wall with

top mounting slots 9" (229mm) above desired display

center as shown in ﬁ gure 2.1 on page 6. Level wall

plate template (wall arm) on wall and mark center of

four mounting holes. Drill four 13/32" (10mm) dia. pilot

holes to a depth of 3" (76mm). Insert anchors (D) into

four holes ﬂ ush with wall as shown (right). Place wall

arm (A) over anchors and secure using three wood

screws (C) and one security wood screw (M). Level,

then tighten all fasteners.

D

2

A

ﬁ g. 2.3

M

C

• When installing Peerless wall mounts on cinder block, verify that you have a minimum of 1-3/8" (35mm) of actual

concrete thickness in the hole to be used for the concrete anchors. Do not drill into mortar joints! Be sure to mount

in a solid part of the block, generally 1" (25mm) minimum from the side of the block. Cinder block must meet ASTM

C-90 speciﬁ cations. It is suggested that a standard electric drill on slow setting is used to drill the hole instead of a

hammer drill to avoid breaking out the back of the hole when entering a void or cavity.

• Concrete must be 2000 psi density minimum. Lighter density concrete may not hold concrete anchor.

• Make sure that the supporting surface will safely support the combined load of the equipment and all attached

hardware and components.

WARNING

• Tighten screws so that wall plate is ﬁ rmly attached,

but do not overtighten. Overtightening can damage

screws, greatly reducing their holding power.

• Never tighten in excess of 80 in. • lb (9 N.M.).

• Always attach concrete expansion anchors directly

to load-bearing concrete.

• Never attach concrete expansion anchors to

concrete covered with plaster, drywall, or other

ﬁ nishing material. If mounting to concrete surfaces

covered with a ﬁ nishing surface is unavoidable (not

evaluated by UL), the ﬁ nishing surface must be

counterbored as shown below. Be sure concrete

anchors do not pull away from concrete when

tightening screws. If plaster/drywall is thicker than

5/8" (16mm), custom fasteners must be supplied by

installer (not evaluated by UL).

WARNING

SOLID CONCRETE

CINDER BLOCK

CUTAWAY VIEW

INCORRECT CORRECT

wall

plate wall

plate

plaster/

dry wall plaster/

dry wall

concrete concrete

1

3

2

D

Drill holes and insert anchors (D).

Place plate (A) over anchors (D) and secure with screws (C,M).

Tighten all fasteners.

A

D

C,M

concrete

surface

#14 SECURITY

SCREW

5/16" WOOD

SCREW

8 of 50 ISSUED: 01-05-11 SHEET #: 061-9062-7 03-22-12

NOTE: If display has a VESA 400 horizontal

mounting pattern, skip to step 3-3 or 3-4 on page

10.

NOTE: For VESA 200x200 or VESA 200x100

mount hole patterns, skip to step 4 on page 11.

NOTE: For dedicated PLP plate installation skip to

step 5 on page 13.

Remove four 1/4-20 x .6" screws using 5 mm allen

wrench (I) and loosen two 1/4-20 x 1.25" screws

1/2 turn to allow for display bracket adjustment.

1/4-20 x .6" SCREWS

1/4-20 x 1.25" SCREWS

3

To prevent scratching the display, set a cloth on a ﬂ at, level surface that will support the weight of the display.

Place display face side down and refer to display manufacturers instructions for removing obstructions from the

back of the display. Adjust display brackets to align with display mounting holes.

Measure horizontal mounting hole pattern and choose ﬁ xed stop-position from chart below.

3-1

FIXED STOP-POSTION #2

FIXED STOP-POSTION #1

FIXED STOP-POSTION #3

horizontal mounting hole pattern fixed stop-position

10-3/4" - 16-1/16" (273 - 408 mm) #1

15-1/16" - 21-9/16" (383 - 548 mm) #2

20-7/16" - 27-9/16" (519 - 700 mm) #3

Installing Adapter Brackets to Display

9 of 50 ISSUED: 01-05-11 SHEET #: 061-9062-7 03-22-12

Select the screws from the bafﬂ ed fastener pack that best ﬁ t your display and secure to display following step 3-3

or 3-4 on page 10.

NOTE: Top and bottom mounting holes must be used for attaching display brackets. Middle holes should also be

used where the fasteners and displays allow.

Verify that all holes are properly aligned, then tighten screws using a phillips screwdriver.

CENTER DISPLAY BRACKETS VERTICALLY AND

HORIZONTALLY ON BACK OF DISPLAY

DISPLAY

DISPLAY BRACKETS

NOTE: "X" dimensions should be equal.

"Y" dimensions should be equal.

• Tighten screws so display brackets are ﬁ rmly attached to display. Do not tighten with excessive force.

Overtightening can cause stress damage to screws, greatly reducing their holding power and possibly causing

screw heads to become detached. Tighten to 40 in. • lb (4.5 N.M.) maximum torque.

• If screws don't get three complete turns in the display inserts or if screws bottom out and bracket is still not tightly

secured, damage may occur to display or product may fail.

WARNING

YY

X

Installing Adapter Brackets to Display

3-2

10 of 50 ISSUED: 01-05-11 SHEET #: 061-9062-7 03-22-12

Begin with the shortest length screw, hand thread

screw through multi-washer and display brackets

(B) into display as shown below. Screw must make

at least three full turns into the mounting hole and

ﬁ t snug into place. Do not over tighten. If screw

cannot make three full turns into the display, select

a longer length screw from the bafﬂ ed fastener

pack. Repeat for remaining mounting holes, level

display brackets and tighten screws.

NOTE: Spacers may not be used, depending upon

the type of display.

Skip to step 3-5.

Begin with the longest length screw, hand thread

screw through multi-washer, display brackets (B)

and spacer in that order into display as shown

below. Screw must make at least three full turns

into the mounting hole and ﬁ t snug into place.

Do not over tighten. If screw cannot make three

full turns into the display, select a shorter length

screw from the bafﬂ ed fastener pack. Repeat for

remaining mounting holes, level display brackets

and tighten screws.

For Flat Back Display

For Bump-out or Recessed Back Display

3-3

3-4

DISPLAY MULTI-WASHER

SCREW

B

DISPLAY MULTI-WASHER

SPACER

B

SCREW

Center display brackets horizontally and vertically

on back of display. Tighten two 1/4-20 x 1.25"

screws. Reinstall four 1/4-20 x .6" screws using

5 mm allen wrench (I) into appropriate ﬁ xed-stop

position from chart on page 8.

3-5 1/4-20 x 1.25" SCREWS

1/4-20 x .6" SCREWS

11 of 50 ISSUED: 01-05-11 SHEET #: 061-9062-7 03-22-12

Remove four 1/4-20 x .6" screws using 5mm allen wrench

(I) and loosen two 1/4-20 x 1.25" screws 1/2 turn to allow for

display bracket adjustment.

Remove four 1/4-20 self tapping screws to detach display brackets from outer mount holes of universal adapter

bracket (B) using 5mm allen wrench (I) as shown in ﬁ gure 4.1. Reinstall four 1/4-20 self tapping screws to secure

display brackets to inner set of mounting holes on universal adapter bracket (B) as shown in ﬁ gure 4.2.

1/4-20 SELF

TAPPING SCREWS 1/4-20 SELF

TAPPING SCREWS

DISPLAY

BRACKETS DISPLAY

BRACKETS

INNER

MOUNTING

HOLES

OUTER

MOUNTING

HOLES

ﬁ g. 4.1 ﬁ g. 4.2

VESA 200 x 200 or VESA 200 x 100 Mounting Pattern

To prevent scratching the display, set a cloth on a

ﬂ at, level surface that will support the weight of the

display. Place display face side down and place

universal adapter bracket (B) onto display.

4-1

4

BB

B

1/4-20 x .6" SCREWS

1/4-20 x 1.25" SCREWS

12 of 50 ISSUED: 01-05-11 SHEET #: 061-9062-7 03-22-12

Slide universal adapter bracket to the opposite side

and align second display bracket with second set of

display mounting holes.

Hand thread screws through multi-washer, display

bracket, and spacer if used, into display as shown.

Tighten all screws.

4-3

SCREW

MULTI-WASHER

MULTI-

WASHER

DISPLAY DISPLAY

BRACKET

VESA 200 x 200 or VESA 200 x 100 Mounting Pattern (Continued)

Align one display bracket with one set of display

mounting holes.

Begin with the shortest length screw, hand thread

screw through multi-washer and display brackets

into display as shown. Screw must make at least

three full turns into the mounting hole and ﬁ t snug

into place. Do not over tighten. If screw cannot

make three full turns into the display, select a longer

length screw from the bafﬂ ed fastener pack. Center

display brackets vertically and tighten screws.

NOTE: For displays with a bump-out or recessed

back, spacer may be used. Spacer goes between

display bracket and display.

4-2 SCREW DISPLAY

DISPLAY

BRACKET

Center display brackets horizontally on back of display as shown in ﬁ gure 4.3.

Tighten two 1/4-20 x 1.25" screws. Reinstall four 1/4-20 x .6" screws using 5 mm allen wrench (I) into ﬁ xed-stop

position 1 as shown in ﬁ gure 4.4.

4-4

ﬁ g. 4.4

1/4-20 x 1.25" SCREWS

FIXED STOP POSITION #1 WITH

1/4-20 x .6" SCREWS

ﬁ g. 4.3

13 of 50 ISSUED: 01-05-11 SHEET #: 061-9062-7 03-22-12

• Do not lift more weight than you can handle. Use additional man power or mechanical lifting equipment to safely

handle placement of the display.

• Do not tighten screws with excessive force. Overtightening can cause damage to mount. Tighten M10 x 15mm

screws (E) to 40 in. • lb (4.52 N.M.) maximum torque.

WARNING

For Dedicated PLP Plate (not evaluated by UL):

Refer to PLP model instruction sheet for attachment

of dedicated PLP plate to display.

Install two M10 x 15mm screws (provided with

dedicated PLP plate) into top two holes of dedicated

PLP plate leaving 1/4" of exposed thread as shown

in ﬁ gure 5.1.

Insert two M10 x 15mm screws (E) into bottom holes of adapter plate as shown in ﬁ gure 5.3 or 5.4. Tighten all

fasteners with 6mm allen wrench (H).

5-1

Mounting Flat Panel Display

5For Universal Adapter Bracket: Hook M10 x 15mm

screws into keyslots of wall arm adapter plate (A) as

shown ﬁ gure 5.2.

A

DEDICATED

PLP PLATE

ADAPTER PLATE ADAPTER PLATE

M10 X 15 MM

SCREW

1/4" M10 X 15 MM

SCREW

1/4"

ﬁ g. 5.1 ﬁ g. 5.2

ﬁ g. 5.3 ﬁ g. 5.4

EE

DEDICATED PLP PLATE

ADAPTER PLATE

DISPLAY NOT

SHOWN FOR

CLARITY

B

14 of 50 ISSUED: 01-05-11 SHEET #: 061-9062-7 03-22-12

TILT Adjustment: Adjust tension knob on side of

mount to desired tension to enable tilt adjustment

and balance your display size and weight. Push

or pull from top or bottom of display to adjust tilt

as shown. The tilt can be adjusted to a maximum

of 10° forward or 5° backward. Retighten tension

knob.NOTE: For larger displays, tension screw on

opposite side of mount may need to be tightened

using 5/32" allen wrench (L).

ROLL Adjustment: Rotate display 5° clockwise or

counter-clockwise, level display then tighten

M5 x 10mm roll screws using 5mm allen wrench (I)

as shown in detail 2.

FOR VERTICAL HEIGHT ADJUSTMENT: Tighten

or loosen M8 x 40mm screw to achieve ± 1" of

vertical height adjustment as shown in detail 2.

7

• Do not tighten screws with excessive force.

• Be careful not to pinch ﬁ ngers when opening and

closing mount from the wall.

CAUTION

TENSION KNOB

DETAIL 2

M5 X 10MM

SCREWS

M8 X 40MM

SCREW

Adjustment of Flat Panel Display

6

• M10 x 15mm screws (E) must be securly tightened before changing orientation of wall arm assembly (A). Failure to

lock adapter bracket can cause display to come off of mount.

WARNING

ﬁ g. 6.1

FOR PORTRAIT OR LANDSCAPE DISPLAY ORIENTATION: Remove two M5 x 12mm screws, one M5 x 6mm

screw and rotation block from top of tilt head as shown in top view and rear view. Gently grasp sides of display and

rotate display into portrait or landscape position as shown in ﬁ gure 6.1 and reinstall rotation block with two

M5 x 12mm screws and one M5 x 6mm screw. NOTE: M5 x 6mm screw required in landscape orientation only.

REAR VIEW

TOP VIEW

ROTATION BLOCK

M5 X 12MM SCREWS

M5 X 6MM SCREWS

M5 X 12MM

SCREWS

M5 X 6MM

SCREWS

15 of 50 ISSUED: 01-05-11 SHEET #: 061-9062-7 03-22-12

KJ

A

GCABLE

DETAIL 3

SLOT

Cable Management

NOTE: Make sure cables have enough slack to

allow full movement of the arm.

Run power cable through top or bottom of arm (A)

and signal cable(s) through other side of arm in

order to avoid interference with the signal. Lock

cables into place by snapping cable covers (J &

K) onto mount as shown. Display may have to be

moved for easy access.

Optional: If additional cable management is

required route cable ties (G) through slots of arm (A)

as shown in detail 3.

8

Snap wall plate covers (F) to top and bottom of wall

plate rails as shown.

9F

WALL PLATE RAIL

16 of 50 ISSUED: 01-05-11 SHEET #: 061-9062-7 03-22-12

If more or less tension is desired in the arm pivot points, do the following:

• To increase tension, turn socket screw clockwise with 5mm allen wrench (I). NOTE: Tighten screws to

50 in • lbs (5.6 N.m.) maximum torque.

• To reduce tension, turn socket screw counter-clockwise with 5mm allen wrench (I). NOTE: Do not turn more

than half a turn.

10

• Do not remove screw or loosen screw until it is no longer engaged with the mount. Doing so may cause the display

to fall.

• If screws become loose over time, tighten screws as necessary. Tighten screws to 50 in • lbs (5.6 N.m.) maximum

torque.

WARNING

TENSION SCREWS

TENSION SCREW

Arm Tension Adjustment

All other brand and product names are trademarks or registered trademarks of their respective owners.

Modelos: ESA763PU

Instalación y montaje:

Soporte articulador resistente a la corrosión para pantallas

planas de 37" a 63" para uso en interiores y exteriores

2300 White Oak Circle • Aurora, Il 60502 • (800) 865-2112 • Fax: (800) 359-6500 • www.peerless-av.com

PUBLICADO: 01-05-11 HOJA #: 061-9062-7 03-22-12

Màxima capcaidad de carga: 200 lb (90.7 kg)

18 de 50 PUBLICADO: 01-05-11 HOJA #: 061-9062-7 03-22-12

Español

• No comience a instalar su producto de Peerless hasta haber leído y entendido las instrucciones y las advertencias

contenidas en la Hoja de Instalación. Si tiene alguna pregunta acerca de cualquiera de las instrucciones o las

advertencias, por favor, llame a Servicio al Cliente de Peerless al 1-800-865-2112 si está en EE. UU. Si es un cliente

internacional, por favor, comuníquese con su distribuidor local.

• Este producto sólo debe ser instalado por una persona que tenga una buena aptitud mecánica, que tenga

experiencia en construcción básica de ediﬁ cios y que entienda estas instrucciones en su totalidad.

• Debido a condiciones ambientales, como grandes cantidades de nieve, granizo, lluvia, etc., el soporte y los

accesorios se tienen que inspeccionar, por lo menos, una vez al año. Este producto no debe estar expuesto a fuertes

vientos. Un instalador o inspector caliﬁ cado debe revisar el soporte para detectar señales de oxidación, sujetadores

sueltos, metales doblados, etc. Si se detectan señales de desgaste excesivo, deterioro o cualquier condición que no

sea segura, se debe descontinuar el uso del producto de inmediato. Dirija todas sus preguntas a Servicio al Cliente,

si tiene alguna.

• Asegúrese de que la superﬁ cie de apoyo sostendrá, con seguridad, la carga combinada del equipo y todos los

ﬁ jadores y componentes.

• Nunca sobrepase la capacidad máxima de soportar carga aceptada por Underwriters Laboratories. Vea la página 17.

• Si va a instalar el producto en una pared con montantes de madera, asegúrese de que los tornillos de montaje estén

anclados en el centro de los montantes. Se recomienda utilizar un localizador de montantes de "borde a borde".

• Siempre cuente con la ayuda de un asistente o utilice un equipo mecánico de izar para levantar y colocar el equipo

con más seguridad.

• Apriete los tornillos con ﬁ rmeza, pero no en exceso. Apretarlos en exceso puede dañar los artículos y puede

disminuir signiﬁ cativamente su fuerza de ﬁ jación.

• Este producto fue diseñado para ser instalado en paredes con la siguiente construcción solamente:

CONSTRUCCIÓN DE LA PARED ACCESORIOS NECESARIOS

• Montante de madera Incluido

• Viga de madera Incluido

• Concreto macizo Incluido

• Bloque de hormigón de escorias Incluido

• Montante de metal No lo instale excepto con el juego de accesorios de Peerless para

montantes de metal (no evaluados por UL)

• Ladrillo Comuníquese con un profesional caliﬁ cado (no evaluados por UL)

• ¿Otra superﬁ cie o no está seguro? Comuníquese con un profesional caliﬁ cado

ADVERTENCIA

NOTA: Lea la hoja de instrucciones completa antes de comenzar la instalación y el ensamblaje.

Herramientas necesarias para el ensamblaje

• localizador de montantes (se recomienda uno de "borde a borde")

•destornillador phillips

•taladro

•broca de 13/32" (10 mm) para paredes de concreto y de bloque de hormigón de escorias, broca de 3/16" (5 mm) para

paredes con montantes de madera

•nivel

Tabla de Contenido

Lista de piezas................................................................................................................................................................19, 20

Instalación en una pared ................................................................................................................................................22, 23

Instalación del soporte adaptador universal ....................................................................................................................24-28

Instalación de la pantalla plana ............................................................................................................................................29

Manejo de los cables ............................................................................................................................................................32

19 de 50 PUBLICADO: 01-05-11 HOJA #: 061-9062-7 03-22-12

Español

Las piezas pueden verse un poco distintas a la ilustración.

Antes de empezar, asegúrese de que todas las piezas que se muestran

son incluidos con su producto.

BCD

EG

M

H

J

L

F

K

I

A

ESA763PU

Descripción Cant. N° de pieza

A

brazo de pared 1 095-T1994

Bsoporte adaptador universal 1 095-T1635-2

C3" tornillos para madera 3 520-D1243

D10mm anclajes de concreto 4 590-0321

Etornillos de M10 x 15mm 2520-D1262

Fcubiertas de la placa de pared 2590-1325

Gsujetacables 16 590-1168

Hllave allen de 6mm 1 560-9716

Illave allen de 5mm 1 560-9640

JCubierta trasera para cables 4 590-P1326

K

Cubierta delantera para cables 4 590-P1327

Lllave allen de 5/32" 1 560-9646

M2.5" tornillo de seguridad para madera 1 520-D1668

Lista de piezas

20 de 50 PUBLICADO: 01-05-11 HOJA #: 061-9062-7 03-22-12

Español

M4 x 12 mm (6)

(510-D1079)

M4 x 25 mm (4)

(510-D1082)

M5 x 12 mm (4)

(520-D1064) M5 x 25 mm (4)

(520-D1122)

M8 x 12 mm (6)

(520-D1068)

M8 x 40 mm (4)

(520-D1152)

M8 x 25 mm (4)

(520-D1101)

I.D. .34" (4)

(540-1059)

I.D. .22" (4)

(540-1057)

M6 x 30 mm (4)

(520-D1067)

M6 x 12 mm (4)

(520-D1050)

M6 x 25 mm (4)

(520-D1211)

M6 x 20 mm (4)

(520-D1554)

Fijaciones para los soportes adaptadores

arandela

múltiple (6)

(580-1036)

La page est en cours de chargement...

Peerless ESA763PU Guide d'installation

Peerless ESA763PU Guide d'installation

dans d''autres langues

Documents connexes

Autres documents