VTech RM7868HD Guide de démarrage rapide

Catégorie
Moniteurs vidéo bébé
Taper
Guide de démarrage rapide
Go to www.vtechphones.com
to register your product for
enhanced warranty support and
latest VTech product news.
Congratulations
on purchasing your new VTech product.
Before using this baby monitor, please read the Important safety instructions.
For support, shopping, and everything new at VTech, visit our website at
www.vtechphones.com. In Canada, visit www.vtechcanada.com.
Frequency Baby unit: 2412 - 2462 MHz
Channels 11
LCD 7’’ Color LCD
(IPS 1280x800 pixels)
Nominal effective range Maximum power allowed by FCC and IC. Actual operating range may
vary according to environmental conditions at the time of use.
Power requirement Baby unit power adapter: Output: 5V DC, 1000mA.
Parent unit power adapter: Output: 5V DC, 2A.
Parent unit battery: 3.7V 5000mAh, 18.5Wh Lithium-ion battery
Specifications are subject to change without notice.
© 2022 VTech Communications, Inc.
All rights reserved. 05/22. RM7766-XHD_QSG_V2
Technical specications
Android TM and Google Play TM are trademarks of Google Inc.
App Store is a trademark of Apple Inc., registered in the U.S. and other countries.
IOS is a trademark or registered trademark of Cisco in the U.S. and other countries and is used under license.
UL STD.
62368-1
CERTIFIED TO
CSA STD.
C22.2 NO.62368-1
CONFORMS TO
RM7868HD
RM7868-2HD
7” Touch Screen Wi-Fi
1080p Pan & Tilt Monitor
What does HD Video Monitor do?
Disclaimer and Limitation of Liability
VTech Communications, Inc. and its suppliers assume no responsibility for any damage or loss
resulting from the use of this user’s manual. VTech Communications, Inc. and its suppliers assume no
responsibility for any loss or claims by third parties that may arise through the use of this product.
Company: VTech Communications, Inc.
Address: 9020 SW Washington Square Road - Ste 555 Tigard, OR 97223, United States
Phone: 1 (800) 595-9511 in the U.S. or 1 (800) 267-7377 in Canada
Quick start guide RM7868HD RM7868-2HD
For more support information
S
m
VTech 7” Touch Screen Wi-Fi 1080p Pan & Tilt Monitor allows you to stay close to your
baby when you are on the move or away. This monitor is Wi-Fi enabled, using your home
wireless network to stream live video and audio through the 1080p baby unit and 7-inch
color screen parent unit. It allows you to maintain a constant connection to your baby.
You can also monitor from your smartphone and mobile tablet.
VTech 7” Touch Screen Wi-Fi 1080p Pan & Tilt Monitor uses MyVTech Baby Pro app to let
you instantly see and hear what’s happening with your baby from anywhere in the world.
The app can be downloaded from the App Store or the Google PlayTM Store.
Direct mode
Your baby monitor parent unit and baby unit connect to each other in Direct mode by
default, which allows you to immediately stream video out of the box.
It is NOT recommended to continue using Direct Mode connection after initial
installation.
You may experience reduced signal
strength if your parent unit and
baby unit are far apart, or there are
obstructing factors, such as internal
walls, between them. You have to
set up Router mode to connect the
units via your home Wi-Fi network to
improve the connection between your
parent unit and baby unit.
Router mode
You are required to set up your
monitor in Router mode to enjoy live
video streaming via your parent unit
with an enhanced connection. Router
mode is the recommended mode for
stable connectivity.
Router mode uses your home Wi-
Fi network to connect your video
monitor. It supports live video
streaming through the parent unit
and smartphone app.
If you want to stream live video
remotely with your mobile device,
download and install the MyVTech
Baby Pro mobile app. With the
mobile app, your Wi-Fi router (not included) provides Internet connectivity to your HD
video monitor system. It serves as a communicating channel between your baby unit and
mobile device, allowing you to monitor and/or control your baby unit wherever you are.
For more details, see Download app for mobile access section in this quick start guide.
When both parent unit and app are viewing the camera simultaneously,
the video quality will be optimised to deliver the best possible viewing result.
Overview
What’s in the box
Connect, charge and power on the baby monitor
Protect your privacy and online security
x 2 x 2
Quick start guide
Your baby monitor package contains the following items. Save your sales receipt and original
packaging in the event warranty service is necessary.
How the system works
VTech cares about your privacy and peace of mind. That’s why we’ve put together a list of industry-recommended best
practices to help keep your wireless connection private and your devices protected when online. We recommend you
carefully review and consider complying with the following tips.
Ensure your wireless connection is secure.
Before installing a device, ensure your router’s wireless signal is encrypted by selecting the “WPA2-PSK with AES”
setting in your router’s wireless security menu.
Change default settings.
Change your wireless router’s default wireless network name (SSID) to something unique.
Change default passwords to unique, strong passwords. A strong password:
- Is at least 10 characters long.
- Is complex.
- Does not contain dictionary words or personal information.
- Contains a mix of uppercase letters, lowercase letters, special characters and numbers.
Keep your devices up to date.
Download security patches from manufacturers as soon as they become available. This will ensure you always have
the latest security updates.
If the feature is available, enable automatic updates for future releases.
Disable Universal Plug and Play (UPnP) on your router.
UPnP enabled on a router can limit the effectiveness of your firewall by allowing other network devices to open
inbound ports without any intervention or approval from you. A virus or other malware program could use this
function to compromise security for the entire network.
For more information on wireless connections and protecting your data, please review the following resources from
industry experts:
1. Federal Communications Commission: Wireless Connections and Bluetooth Security Tips –
www.fcc.gov/consumers/guides/how-protect-yourself-online.
2. U.S. Department of Homeland Security: Before You Connect a New Computer to the Internet –
www.us-cert.gov/ncas/tips/ST15-003.
3. Federal Trade Commission: Using IP Cameras Safely –
https://www.consumer.ftc.gov/articles/0382-using-ip-cameras-safely.
4. Wi-Fi Alliance: Discover Wi-Fi Security –
http://www.wi-fi.org/discover-wi-fi/security.
Parent unit icons
For mobile access:
MyVTech Baby Pro mobile app
Network Wi-Fi
Wi-Fi router 2.4GHz 802.11 b/g/n
Internet connection 1.5 Mbps @ 720p or 2.5 Mbps @1080p upload
bandwidth per baby unit
Requirements
Main
Menu Options
Monitoring mode (* For RM7868-2HD only)
View baby units in Single mode.
View baby units in Patrol mode.
View baby units in Split screen.
Night light
Turn on or turn off night light.
Select a night light color.
Adjust night light brightness.
Set a night light timer.
Melodies and soothing sounds
Select play all melodies, or play
one of the five melodies and five
soothing sounds.
You can also set the timer to stop
playing after 15, 30 or 60 minutes,
or playing non-stop.
Adjust baby unit speaker volume.
General settings
Connect to home Wi-Fi network.
Connect mobile phone.
Turn on/off parking mode
Adjust parent unit screen
brightness
Set screen lock timer
Set screen off timer
Temperature display format
Reset settings, software update.
Alerts Settings
Adjust alerts volume
Turn on/off temperature alert
Select maximum and minimum
temperature for alert range.
Turn on/off low battery alert tone
Turn on/off motion detection
alert tone
Select motion sensitivity level.
Turn on/off no link alert
Main
Menu Options
Help and info
Support information
System information
Privacy information
Connect the baby monitor
The rechargeable battery in the parent unit is built-in.
Use only the power adapters supplied with this product.
Make sure the parent unit and the baby unit are not connected to the switch controlled electric outlets.
Connect the power adapters in a vertical or floor mount position only. The adapters’ prongs are not
designed to hold the weight of the parent unit and the baby unit, so do not connect them to any ceiling,
under-the-table, or cabinet outlets. Otherwise, the adapters may not properly connect to the outlets.
Make sure the parent unit, the baby unit and the power adapter cords are out of reach of children.
Charge the parent unit battery before use
The parent unit runs on rechargeable battery or AC power. To continuously monitor your
baby, keep the parent unit connected to AC power.
Before using the baby monitor for the first time, charge the parent unit battery for 12 hours. When
the parent unit battery is fully charged, the battery icon becomes solid .
The standby time varies depending on your actual use.
The parent unit turns on automatically after connecting to the power socket, and the
welcome screen appears. You can press Power o turn the parent unit on or press and
hold to turn it off.
The battery icon indicates the battery status (see the following table).
Battery indicators Battery status Action
The screen displays and
.
The LED light flashes.
The battery has very little
charge and may be used
for only a short time.
Charge
without interruption
(about 30 minutes).
The battery icon becomes solid
.
The battery is fully
charged. To keep the battery charged,
connect it to AC power when
in use.
1 set for RM7868HD
2 sets for RM7868-2HD
Slide the switch to ON to power on your baby unit.
When powering up, the baby unit’s status LED turns on.
It will turn off after a while and keeps off.
The status LED is set to off by default.
NOTE:
Camera lens and surface may get
warm during normal operation.
WARM
WARM
Parent unit overview
13- level sound indicator light
Green: low sound level is detected by
the baby unit.
Green and amber: moderate sound
level is detected by the baby unit.
Green, amber and red: high sound level
is detected by the baby unit.
2LINK LED light
On when the parent unit is linked to the
baby unit.
Flashes when the link to the baby unit
is lost.
3 LED light
On when the parent unit is connected to
AC power, and the battery is charging.
Flashes when the parent unit battery is
low and needs to be charged.
4TALK /
Press and hold to talk to the baby unit.
While in a sub-menu, press to exit.
5MENU | SELECT
Press to enter the main menu.
While in a menu, press to choose an
item, or save a setting.
6 | | | Arrow keys
Press to navigate leftward, upward,
rightward or downward, within the
main menu and sub-menus.
While viewing a zoomed image, press
to move the image leftward, upward,
rightward or downward.
7 |
Increase or decrease parent unit
volume.
8 Zoom
Press to zoom in/out.
While in a sub-menu, press to view the
help menu.
9 Power | LCD ON/OFF
10 Microphone
11 Touch screen
12 Antenna
13 Speaker
14 Power jack
15 RESET
Force reboot the parent unit.
16 Stand
Mobile access
Connecting Wi-Fi to
enhance local access
2
1
3
4
5
6
7
8
9
10
11
16
15
14
13
12
Install MyVTech Baby Pro mobile app
1. Browse the App Store or the Google Play store .
2. Search for the mobile app with the keyword “myvtech baby pro“.
3. Download and install the MyVTech Baby Pro mobile app to your mobile device.
OR
Scan the QR codes on the right to get the app.
Make sure your mobile device meets the minimum
requirement for the mobile app.
Minimum requirement
The mobile app is compatible with:
AndroidTM 6.0 or later; and
iOS 12 or later.
Download the free MyVTech Baby Pro mobile app and install it to a
mobile device, then use your mobile device and the mobile app to
monitor your areas remotely.
1. Press MENU when the parent unit is idle.
2. Go to > > Connect Mobile Phone.
3. Scan the QR code in the parent unit to download the app into your
mobile device.
4. Follow the instructions in the mobile app to set up and pair your baby
unit to the mobile app.
Alternatively, you can download the mobile app from the App Store or
Google Play store.
1
Download app for mobile access
After installing the mobile app, follow the instructions in the mobile app and parent
unit to set up and pair your baby unit.
In your mobile device:
1. Tap to run the mobile app in your mobile device, and then create a user account.
2. We recommend that you use common webmail services, such as Google Gmail for
registration of your user account. Check your email (and Spam folder), and activate
your new camera account via the email link, then sign in to your account.
3. Follow the instructions in the mobile app to pair the camera. Tap , then Add Camera
in the mobile app to get started.
2
The applied nameplate is located at the bottom of the baby unit’s base.
When using your equipment, basic safety precautions should
always be followed to reduce the risk of fire, electric shock and
injury, including the following:
1. Follow all warnings and instructions marked on the product.
2. Adult setup is required.
3. CAUTION: Do not install the baby unit at a height above 6.5
feet (2 meters).
4. This product is intended as an aid. It is not a substitute for
responsible and proper adult supervision and should not be
used as such.
5. This product is not intended for use as a medical monitor.
6. Do not use this product near water. For example, do not use
it next to a bath tub, wash bowl, kitchen sink, laundry tub or
swimming pool, or in a wet basement or shower.
7. CAUTION: Use only the battery provided. There may be a risk
of explosion if a wrong type of battery is used for the parent
unit. The battery cannot be subjected to high or low extreme
temperature and low air pressure at high altitude during use,
storage or transportation. Disposal of battery into fire or a hot
oven, or mechanically crushing or cutting or the battery can
result in an explosion. Leaving the battery in an extremely
high temperature surrounding environment can result in an
explosion or the leakage of flammable liquid of gas. Battery
subjected to extremely low air pressure may result in an
explosion or the leakage of flammable liquid or gas. Dispose
of used battery according to the information in The RBRC seal.
8. Use only the adapters included with this product. Incorrect
adapter polarity or voltage can seriously damage the product.
Power adapters information:
Baby Unit Output: 5V DC 1000mA
VTech Telecommunications Ltd.
Model: VT05EUS05100
Parent Unit Output: 5V DC 2A
VTech Telecommunications Ltd.
Model: VT07EUS05200
Rechargeable battery information:
3.7V 5000mAh, 18.5Wh Lithium-ion battery
Zhuhai Great Power Energy Co., Ltd.
Model: GSP806090-5Ah-3.7V-1S1P
9. The power adapter is intended to be correctly oriented in a
vertical or floor mount position. The prongs are not designed
to hold the plug in place if it is plugged into a ceiling, under-
the-table or cabinet outlet.
10. For pluggable equipment, the socket-outlet (power adapter)
shall be installed near the equipment and shall be easily
accessible.
11. Unplug this product from the wall outlet before cleaning.
Do not use liquid or aerosol cleaners. Use a damp cloth for
cleaning.
12. Do not cut off the power adapters to replace them with other
plugs, as this causes a hazardous situation.
13. Do not allow anything to rest on the power cords. Do not
install this product where the cords may be walked on or
crimped.
14. This product should be operated only from the type of power
source indicated on the marking label. If you are not sure of
the type of power supply in your home, consult your dealer or
local power company.
15. The equipment is to be supplied from an identified USB port
complying with the requirements of Limited Power Source.
16. Do not overload wall outlets or use an extension cord.
17. Do not place this product on an unstable table, shelf, stand or
other unstable surfaces.
18. This product should not be placed in any area where proper
ventilation is not provided. Slots and openings in the back or
bottom of this product are provided for ventilation. To protect
them from overheating, these openings must not be blocked
by placing the product on a soft surface such as a bed, sofa
or rug. This product should never be placed near or over a
radiator or heat register.
19. Never push objects of any kind into this product through
the slots because they may touch dangerous voltage points
or create a short circuit. Never spill liquid of any kind on the
product.
20. To reduce the risk of electric shock, do not disassemble this
product, but take it to an authorized service facility. Opening
or removing parts of the product other than specified access
doors may expose you to dangerous voltages or other risks.
Incorrect reassembling can cause electric shock when the
product is subsequently used.
21. You should test the sound reception every time you turn on
the units or move one of the components.
22. Periodically examine all components
for damage.
23. There is a very low risk of privacy loss when using certain
electronic devices, such as baby monitors, cordless
telephones, etc. To protect your privacy, make sure the
product has never been used before purchase, reset the baby
monitor periodically by powering off and then powering on
the units, and power off the baby monitor if you will not use it
for some time.
24. Children should be supervised to ensure that they do not play
with the product.
25. The small parts of this monitor can be swallowed by babies or
small children. Keep these parts out of reach of children.
26. The product is not intended for use by persons (including
children) with reduced physical, sensory or mental capabilities,
or lack of experience and knowledge, unless they have
been given supervision or instruction concerning use of the
appliance by a person responsible for their safety.
SAVE THESE INSTRUCTIONS
Cautions
Use and store the product at a temperature between 32oF and
104oF.
Burn hazard, fire hazard, explosion hazard associated with
mishandling of the battery.
Do not expose the product to extreme cold, heat or direct
sunlight. Do not put the product close to a heating source.
Warning—Strangulation Hazard—Children
have STRANGLED in cords. Keep this cord out of
the reach of children (more than 3 ft (0.9m) away).
Do not remove this tag.
Never place the camera unit(s) inside the baby’s crib or
playpen. Never cover the camera unit(s) or parent unit with
anything such as a towel or a blanket.
Other electronic products may cause interference with your
camera unit. Try installing your camera unit as far away from
these electronic devices as possible: wireless routers, radios,
cellular telephones, intercoms, room monitors, televisions,
personal computers, kitchen appliances and cordless
telephones.
Precautions for users of implanted cardiac pacemakers
Cardiac pacemakers (applies only to digital cordless devices):
Wireless Technology Research, LLC (WTR), an independent
research entity, led a multidisciplinary evaluation of the
interference between portable wireless devices and implanted
cardiac pacemakers. Supported by the U.S. Food and Drug
Administration, WTR recommends to physicians that:
Pacemaker patients
Should keep wireless devices at least six inches from the
pacemaker.
Should NOT place wireless devices directly over the
pacemaker, such as in a breast pocket, when it is turned ON.
WTR’s evaluation did not identify any risk to bystanders with
pacemakers from other persons using wireless devices.
Electromagnetic fields (EMF)
This VTech product complies with all standards regarding
electromagnetic fields (EMF). If handled properly and according
to the instructions in this user’s manual, the product is safe to be
used based on scientific evidence available today.
Important safety instructions
Raise the parent unit
antenna for better
reception
Status icons
Direct mode
Parent unit, baby unit 1 and baby unit 2
(*For RM7868-2HD only) are connected to
each others directly.
Red bars indicate no connection.
Wi-Fi Router mode
Parent unit, baby unit 1 and baby unit 2
(*For RM7868-2HD only) are connected to
home Wi-Fi network.
The red icon(s) on the baby unit or parent
unit, indicates no connection between the
respective unit(s) and the router.
Baby unit 1 and 2 are being viewed in
Patrol mode (*For RM7868-2HD only).
Baby unit 1 and 2 are being viewed in
Split mode (*For RM7868-2HD only).
Touch screen is locked.
Night vision is turned on.
Motion detection alert is turned on.
Melodies and soothing sounds are
playing.
Night light is turned on.
Auto night light brightness is activated.
Temperature alert is turned on.
Parent viewer is muted.
Battery indicator.
1Light sensor
2Camera lens
3Infrared LEDs
Allow you to see clearly in a dark environment.
4Microphone
5Night Light
6 Night Light Control Key
Go to Night Light section to learn more.
7LED indicator
Red is steadily on when the baby unit is
connecting to the parent unit in direct mode.
Green is steadily on when the baby unit is
connected in Wi-Fi router mode.
Red flashing slowly during video streaming in
direct mode.
Green flashes slowly during video streaming
in Wi-Fi router mode.
8ON/OFF switch
Power it on or off.
9Speaker
10 Temperature sensor
11 Power jack
12 Wall mount slots
13 PAIR
Press and hold for three seconds to enter
pairing mode.
Reset the baby unit to factory default.
1. Press and hold PAIR key until you hear a
beep sound.
2. Release the PAIR key, and then press the
PAIR key again five times until you hear
another beep sound.
3. The baby unit will sound another beep
when the reset completes. Then, the
baby unit will reboot.
7
8
9
10
4
6
5
2
11
12
13
1
3
7
8
9
10
4
6
5
2
11
12
13
1
3
7
8
9
10
4
6
5
2
11
12
13
1
3
Baby unit overview
CABLE MANAGEMENT
1 2 3
Local access
Local access, for
start up quick view
and setup stage.
After powering up your video monitor, the parent unit streams live video in direct mode.
We recommend you follow the instructions on screen to set up home Wi-Fi network
with your monitor for functionality enhancements and mobile access. See Auto software
and firmware update and Download app for mobile access in this quick start guide.
Use the Control Panel
Tap the screen to open and use the Control Panel.
Tap to lock the panel, and tap to unlock it.
Use the Main Menu
Press MENU on the parent unit to enter the
main menu, choose a menu item, or save a
setting. You can use the parent unit menu for
advanced settings or operations, such as to
play or stop the baby unit lullaby, or adjust the
baby unit sound sensitivity.
While in the menu:
Press | | | to scroll among the
menu options.
Press SELECT to select an item.
Press TALK to return to the live video.
Press to go to the Help & info page.
To keep this product working well and looking good, follow these guidelines:
Avoid placing it near heating appliances and devices that generate electrical noise (for example,
motors or fluorescent lamps).
DO NOT expose it to direct sunlight or moisture.
Avoid dropping the product or treating it roughly.
Clean with a soft damp cloth.
DO NOT immerse the parent unit and the baby unit in water and do not clean them under the tap.
DO NOT use cleaning spray or liquid cleaners.
Make sure the parent unit and the baby unit are dry before you connect them to the mains again.
Clean the USB charging port of dust, dirt, and lint regularly.
When you are not going to use the video monitor for some time, store the parent unit, the baby unit
and the adapters in a cool and dry place.
Below are the questions most frequently asked about the video monitor.
Can I turn the parent
unit display screen
off but keep hearing
sounds from the baby
unit?
Yes, press | LCD ON/OFF on the parent unit to turn off the screen. The parent
unit display will also dim automatically after being inactive for some time. In both
instances, you will still be able to hear all sounds from the baby unit.
Press any key to turn the screen back on.
Why is the baby
unit not responding
normally?
Try the following (in the order listed) for a common cure:
1. Disconnect the power to the baby unit.
2. Wait a few minutes before connecting power back to the baby unit.
3. Reboot the parent unit.
Why is my screen in
black and white?
The baby unit has a light sensor that measures ambient light. When the
ambient light is dim, such as during night time or in a dark room, the baby unit
activates its infrared LEDs, and displays the camera images in black and white
night vision.
Why does my baby unit
show offline? Why is the
connection lost every
now and then?
The baby unit may have lost connection to the Wi-Fi router. Check your
network and router settings.
Other electronic products may cause interference with your baby unit. Try
installing your baby unit as far away from these electronic devices as possible.
Why can’t I hear a
sound/Why can’t I hear
my baby crying?
The parent unit speaker volume may be too low. Press on the parent unit
to increase the volume.
You may have set a low sound sensitivity level. Set the sound sensitivity to a
higher level. For details, go to www.vtechphones.com for online help topics.
Frequently asked questions
General product care
Storage
mount the baby unit (optional)
1. Place the wall mount bracket on a
wall and then use a pencil to mark
two holes in parallel. Remove the
wall mount bracket and drill two
holes in the wall (7/32 inch drill bit).
NOTESNOTE
Notes
Check for reception strength and
camera angle of the baby unit before
drilling the holes.
The types of screws and plugs you need
depend on the composition of the wall.
You may need to purchase the screws
and plugs separately to mount your
baby units.
2. If you drill the holes into a stud, go
to step 3.
If you drill the holes into an
object other than a stud, insert
the wall plugs into the holes.
Tap gently on the ends with a
hammer until the wall plugs are
flush with the wall.
3. Align the wall mount bracket and screws with
the holes in the wall as shown. Tighten the screw
in the middle hole first, so that the wall mount
bracket position is fixed. You can tighten the
other screw in the top hole.
3. Insert the screws into the holes and
tighten the screws until only 1/4 inch of
the screws are exposed.
4. Place the baby unit on the wall
mount bracket, and then slide it
forward until it locks into place. Align
the holes on the wall mount bracket
with the screws on the wall, and slide
the wall mount bracket down until it
locks into place.
5. You can maximize your baby unit’s viewing angles by tilting the wall mount bracket.
Hold the baby unit, and then rotate the knob in anticlockwise direction. This will loosen the joint of the wall mount bracket.
Tilt your baby unit up or down to adjust to your preferred angle. Then, rotate the knob in clockwise direction to tighten the joint
and secure the angle.
OR
4. Place the baby unit on the wall mount bracket,
and then slide it forward until it locks into place.
Connect the power adapter to the baby unit
and a power supply not controlled by a wall
switch.
12
Need help?
Use your smartphone or mobile device to access our online help.
Go to https://help.vtechphones.com/RM7868HD or
https://help.vtechphones.com/RM7868-2HD; OR
Scan the QR code on the right. Launch the camera app or
QR code scanner app on your smartphone or tablet. Hold
the device’s camera up to the QR code and frame it. Tap
the notification to be redirected to the online help page.
- If the QR code is not clearly displayed, adjust your
camera’s focus by moving your device closer or
further away until the image is clear.
If you would like to contact us, visit
https://help.vtechphones.com/cs.
You can also call our Customer Support at
1-844-848-8324 (1-844-84-VTECH) [in US] or
1-888-211-2005 [in Canada] for help.
Test the sound level and position the baby monitor
Basic operation
S
m
For instructions and guides to make the best use of your baby monitor,
and for the latest information and support, check out our online
help topics and FAQs. The online help page will also be updated
periodically to reflect product system updates.
To ensure that your HD video monitor is always at its best performance, the Parent Unit
will prompt a message and ask you to update its software and the Baby Unit’s firmware
when there are new versions available. Select “Now” to reboot the system, or switch off
and on the Parent Unit later to reboot the system into the latest software.
To check if your device is running on the latest software, or to update your device
software, go to:
> > Software Update.
Connect your HD video monitor with home Wi-Fi network
You must connect your video monitor to your secured home Wi-Fi network in order to
receive the latest software and firmware updates. To set the Wi-Fi up, go to:
> > Congure Wi-Fi.
Make sure the Baby Unit is on when you set up the Wi-Fi network.
Auto software and rmware update
If you plan to install your baby unit in a designated
location, and use your home Wi-Fi network to
connect your video monitor, you need to test
which of your selected monitoring areas within the
house have good Wi-Fi signal strength. After you
have powered on your parent unit, you can use
your parent unit’s Wi-Fi signal strength indicator
to assist in checking. Once you have identified the
suitable location, you can install your baby unit.
Adjust the distance between your baby unit and
the Wi-Fi router if needed.
Depending on surroundings and obstructing factors,
such as the effect distance and internal walls have on
signal strength, you may experience reduced Wi-Fi
signal. To improve the Wi-Fi signal strength, adjust the
distance or direction of your parent unit. Check with
your parent unit again.
test the location for the baby unit
Talk to your baby via the baby unit
1. Press and hold the TALK key.
2. When the icon displays on
screen, speak to your parent unit.
Your voice is transmitted to the
baby unit.
3. When finished talking, release
the TALK key to hear your baby
again.
Zoom
Press to zoom in or out in a fixed
zoom sequence. indicates that the
image is magnified 3 times.
Adjust speaker volume
Press | to adjust the parent unit
speaker volume level received from the
baby unit.
You can reset the parent unit by pressing the
RESET key at the back of the unit.
Insert a pin into the RESET hole on the back of
the parent unit, and then press the key inside.
Turn on/off the parent unit screen
You can turn on or turn off the parent unit
screen without powering off the unit. You
will still hear sounds from the baby unit.
Press | LCD ON/OFF on the parent unit
to turn off the screen.
Press any key on the parent unit to turn
the screen on again.
Testing the sound level of the baby monitor
This baby monitor is intended as an aid. It is not a substitute for proper adult supervision, and should
not be used as such.
For hearing protection, make sure the parent unit is more than 3 feet away from the baby
unit. If you hear any feedback noise from the parent unit, move the parent unit further until
the noise stops. You can also press on the parent unit to lower or mute the noise.
Increase the parent unit speaker volume if you cannot hear the sounds transmitted from the baby unit.
RM7868HD online help
RM7868-2HD online help
> 3ft
< 3ft (1m)
> 3ft (1m)
Muted
Press and hold
FCC and IC regulations
FCC Part 15
NOTE: This equipment has been tested and found to comply with the requirements for a Class B digital device under Part 15 of
the Federal Communications Commission (FCC) rules. These requirements are intended to provide reasonable protection against
harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not
installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is
no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio
or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the
interference by one or more of the following measures:
Reorient or relocate the receiving antenna.
Increase the separation between the equipment and receiver.
Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
Consult the dealer or an experienced radio/TV technician for help.
WARNING: Changes or modifications to this equipment not expressly approved by the party responsible for compliance could void
the user’s authority to operate the equipment.
This device complies with Part 15 of the FCC rules. Operation is subject to the following two conditions: (1) this device may not cause
harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired
operation.
To ensure safety of users, the FCC has established criteria for the amount of radio frequency energy that can be safely absorbed by a
user or bystander according to the intended usage of the product. This product has been tested and found to comply with the FCC
criteria. The baby unit shall be installed and used such that parts of all persons’ body are maintained at a distance of approximately 8 in
(20 cm) or more. The transmitter and antenna of the parent unit shall be held at least 1 in (2.5 cm) from your face.
This Class B digital apparatus complies with Canadian requirement:
CAN ICES-3 (B)/NMB-3(B)
Industry Canada
This device contains licence-exempt transmitter(s)/receiver(s) that comply with Innovation, Science and Economic Development Canada’s
licence-exempt RSS(s). Operation is subject to the following two conditions: (1) This device may not cause interference. (2) This device must
accept any interference, including interference that may cause undesired operation of the device.
The term ‘’IC:‘’ before the certification/registration number only signifies that the Industry Canada technical specifications were met.
This product meets the applicable Innovation, Science and Economic Development Canada technical specifications.
RF radiation exposure statement
The product complies with FCC RF radiation exposure limits set forth for an uncontrolled environment. The baby unit should be
installed and operated with a minimum distance of 8 in (20 cm) between the baby unit and all persons’ body. Use of other accessories
may not ensure compliance with FCC RF exposure guidelines. This equipment complies also with Industry Canada RSS-102 with respect
to Canada’s Health Code 6 for Exposure of Humans to RF Fields.
La plaque signalétique appliquée est située au bas du socle de
l’unité du bébé.
Lorsque vous utilisez votre appareil, vous devriez toujours suivre
certaines mesures de précaution de base afin de réduire les risques
d’incendie, d’électrocution et de blessures corporelles, dont ceux
qui suivent:
1. Observez toutes les instructions et mises en garde inscrites sur
l’appareil.
2. L’installation par un adulte est requise.
3. MISE EN GARDE: N’installez pas l’unité du bébé à une hauteur
supérieure à 2 mètres.
4. Ce produit a été conçu pour être un dispositif d’appoint
seulement. Il n’est pas le remplacement d’une supervision
responsable et adéquate par un adulte et ne devrait pas être
utilisé comme telle.
5. Ce produit n’est pas conçu pour être utilisé en tant que moniteur
médical.
6. N’utilisez pas cet appareil près de l’eau ni de toute autre source
d’humidité, par exemple, près d’une baignoire, cuve à lessive,
évier de cuisine, dans un sous-sol humide ni près d’une piscine,
dans un soussol humide ou une douche.
7. MISE EN GARDE: Utilisez uniquement la pile fournie. Un
risque d’explosion pourrait survenir si un mauvais type de
pile est utilisé pour l’unité du parent. La pile ne peut pas être
soumise à des températures extrêmes élevées ou basses et à
une faible pression d’air à haute altitude pendant l’utilisation,
l’entreposage ou le transport. L’élimination de la pile dans le
feu ou dans un four chaud, ou l’écrasement ou le découpage
mécanique de la pile peuvent entraîner une explosion. Laisser
la pile dans un environnement à température extrêmement
élevée peut entraîner une explosion ou la fuite d’un liquide ou
d’un gaz inflammable. Une pile soumise à une pression d’air
extrêmement basse peut provoquer une explosion ou une
fuite de liquide ou de gaz inflammable. Éliminer la pile usagée
conformément aux informations du Sceau RBRC.
8. N’utilisez que les adaptateurs inclus avec ce produit. L’utilisation
d’un adaptateur dont la polarité ou la tension serait inadéquate
risque d’endommager sérieusement le produit et mettre votre
sécurité en péril.
Informations sur les adaptateurs électriques :
Sortie : 5 V CC 1000mA.
VTech Telecommunications Ltd.
Mole : VT05EUS05100
Sortie : 5 V CC 2A.
VTech Telecommunications Ltd.
Mole : VT07EUS05200
Informations sur les piles rechargeables :
3.7V 5000mAh, 18.5Wh Lithium-ion batterie
Zhuhai Great Power Energy Co., Ltd.
Mole : GSP806090-5Ah-3.7V-1S1P
9. Lorsqu’ils sont branchés dans une prise de courant, les
adaptateurs secteur ont été conçus pour être orientés
correctement, soit à la verticale ou au plancher. Les broches
n’ont pas été conçues pour supporter le poids du bloc
d’alimentation et le maintenir en place si celuici est branché dans
une prise au plafond, sous une table ou dans un meuble.
10. Pour les appareils raccordés, la prise de courant (de l’adaptateur
secteur) doit être installée près de l’équipement et doit être
facilement accessible.
11. Débranchez ce produit de la prise de courant avant de
procéder au nettoyage. N’utilisez pas de nettoyants en aérosols.
Utilisez un chiffon humide pour le nettoyer.
12. Ne coupez pas les cordons d’alimentation pour remplacer les
fiches, car ceci peut présenter un danger potentiel.
13. Ne laissez aucun objet reposer ni appuyer sur le cordon
d’alimentation. N’installez pas cet appareil dans un endroit où
l’on risque d’écraser le cordon d’alimentation ou de le piétiner.
14. Ne faites fonctionner cet appareil qu’avec le type d’alimentation
indiqué sur l’étiquette. Si vous ne connaissez pas le type
d’alimentation que vous possédez à votre domicile, consultez
votre marchand ou votre compagnie locale d’électricité.
15. L’équipement doit être fourni à partir d’un acquiescement
gauche identifié d’USB aux conditions de la source d’énergie
limitée.
16. Ne surchargez pas les prises de courant murales ni les rallonges
électriques.
17. Ne placez pas cet appareil sur un chariot, meuble, trépied,
support de montage ni table chancelants.
18. Les trous et ouvertures du boîtier, situés à l’arrière de l’appareil
ou sous celui-ci, servent à aérer l’appareil. Pour l’empêcher de
surchauffer, ne bloquez sous aucun prétexte ces ouvertures et
n’empêchez pas l’aération adéquate de l’appareil en le plaçant
sur un lit, divan, tapis ou toute autre surface similaire. De même,
ne le positionnez pas à proximité ni au-dessus d’une source de
chaleur ou d’un calorifère. De plus, ne placez pas l’appareil dans
un endroit avant de vous assurer qu’il y ait une bonne circulation
d’air.
19. N’enfoncez jamais d’objets à travers les ouvertures de cet
appareil, car ils pourraient entrer en contact avec des points de
tension dangereux ou causer des courts-circuits qui peuvent
dégénérer en incendies ou en risques d’électrocution. Ne
renversez jamais de liquide dans ce produit.
20. Afin de réduire les risques d’électrocution, ne démontez pas cet
appareil, mais apportez-le dans un centre de service autorisé.
L’ouverture du boîtier ou le retrait de toutes pièces que contient
cet appareil, à l’exception de l’accès autorisé à certaines portes
ou ouvertures, risque de vous exposer à des points de tension
dangereux ou d’autres dangers. Un remontage incorrect peut
par la suite présenter des risques d’électrocution.
21. Vous devriez tester la réception chaque fois que vous mettez
l’appareil en fonction.
22. Examinez les composantes afin de vérifier si celles-ci ne sont pas
endommagées.
23. Il existe un très faible risque de perte de confidentialité
avec certains appareils électroniques (autres écoute-bébés,
téléphones sans fils etc.). Pour l’éviter, s’assurer que le produit
n’a jamais été utilisé avant l’achat, réinitialiser l’unité de façon
périodique, éteindre l’écoute-bébé quand il n’est pas en cours
d’utilisation.
24. Les enfants devraient être supervisés afin de vous assurer qu’ils
ne jouent pas avec l’appareil.
25. Les petites pièces de ce moniteur peuvent être avalées par les
bébés ou les petits enfants. Veuillez tenir ces pièces hors de
portée des enfants.
26. Le produit n’est pas conçu pour être utilisé par des personnes
(incluant des enfants) aux capacités physiques, sensorielles
ou mentales réduites ou qui manquent d’expérience et de
connaissances, à moins qu’on leur ait donné suffisamment
de supervision ou d’instructions relativement à l’utilisation de
l’appareil par une personne responsable de leur sécurité.
CONSERVEZ CES INSTRUCTIONS
Mises en garde
Utilisez et entreposez le produit à une température entre 0˚ C
(32˚F) et 40˚C (104˚ F).
Risque de brûlure, risque d’incendie, risque d’explosion associé
à une mauvaise manipulation de la batterie.
N’exposez pas cet appareil à des froids ou des chaleurs
extrêmes, ainsi qu’à la lumière directe du soleil. Ne l’installez pas
près d’une source de chauffage.
Avertissement - Risque de strangulation -
Les enfants se sont ÉTRANGLÉS dans des cordons.
Gardez ce cordon hors de portée des enfants (à plus
de 0,9 m). N’enlevez pas cette étiquette.
Ne jamais placer le moniteur à l’intérieur du berceau ou du parc
de bébé. Ne jamais couvrir le moniteur ou l’unité (s) portative
avec un article tel une serviette ou une couverture.
D’autres produits électroniques peuvent causer des
interférences auprès de votre caméra IP. Essayez d’installer
votre caméra IP le plus loin possible de ces dispositifs
électroniques : routeurs sans fil, radios, téléphones cellulaires,
interphones, moniteurs de pièces, téléviseurs, ordinateurs
personnels, appareils électriques de cuisine et téléphones sans
fil.
Stimulateurs cardiaques implantés dans l’organisme
Les simulateurs cardiaques (ne s’applique qu’aux dispositifs
numériques sans fil):
L’organisme ‘Wireless Technology Research, LLC (WTR)’, une
firme de recherche indépendante, a mené une évaluation
pluridisciplinaire des interférences entre les téléphones sans fil
portatifs et les stimulateurs cardiaques implantés dans l’organisme.
Appuyée par l’Administration des aliments et drogues (FDA) des
États-Unis, la firme WTR recommande aux médecins:
Avis aux détenteurs de stimulateurs cardiaques
Vous devriez maintenir les dispositifs sans fil à au moins six
pouces du simulateur cardiaque.
Ils ne doivent PAS placer le téléphone sans fil directement sur
le stimulateur cardiaque, tel que dans une poche de chemise,
lorsque celui-ci est en marche.
L’étude effectuée par l’organisme WRS n’a pas identifié de risque
pour les détenteurs de simulateurs cardiaques causés par les gens
qui utilisent dispositifs sans fil à proximité de ceux-ci.
Champs électromagnétiques (EMF)
Ce produit de VTech est conforme à toutes les normes se rapportant
aux champs électromagnétiques (EMF) standard. Si vous le
manipulez correctement en suivant les instructions de ce guide, son
utilisation sera sécuritaire pendant de nombreuses années, selon les
meilleures évidences scientifiques dont nous disposons aujourd’hui.
California Energy Commission battery
charging testing mode
This video monitor meets the California Energy Commission (CEC) regulations for energy consumption. Your video monitor is set up to
comply with the energy-conserving standards right out of the box.
Follow the instructions to install and charge the battery. The CEC battery charging testing mode is activated while charging.
Even if the parent unit is paired to camera units, the CEC battery charging testing mode is activated while it is powered off and
charging.
For cETL compliance only
What does this limited warranty cover?
The manufacturer of this VTech Product warrants to the
holder of a valid proof of purchase (“Consumer” or “you”)
that the Product and all accessories provided in the sales
package (“Product”) are free from defects in material
and workmanship, pursuant to the following terms and
conditions, when installed and used normally and in
accordance with the Product operating instructions. This
limited warranty extends only to the Consumer for Products
purchased and used in the United States of America and
Canada.
What will VTech do if the Product is not free from defects
in materials and workmanship during the limited warranty
period (“Materially Defective Product”)?
During the limited warranty period, VTech’s authorized
service representative will replace at VTech’s option, without
charge, a Materially Defective Product. If we choose to
replace the Product, we may replace it with a new or
refurbished Product of the same or similar design. We will
retain defective parts, modules, or equipment. Replacement
of the Product, at VTech’s option, is your exclusive remedy.
VTech will return the replacement Products to you in
working condition. You should expect the replacement to
take approximately 30 days.
How long is the limited warranty period?
The limited warranty period for the Product extends for
ONE (1) YEAR from the date of purchase (90 days on
products purchased as Refurbished*). This limited warranty
also applies to the replacement Product for a period of
either (a) 90 days from the date the replacement Product
is shipped to you or (b) the time remaining on the original
one-year warranty (90-day limited warranty on products
that are purchased as Refurbished*); whichever is longer.
*Refurbished products purchased from our online store
carry a 90-day replacement warranty.
What is not covered by this limited warranty?
This limited warranty does not cover:
1. Product that has been subjected to misuse, accident,
shipping or other physical damage, improper installation,
abnormal operation or handling, neglect, inundation,
fire, water or other liquid intrusion; or
2. Product that has been damaged due to repair, alteration
or modification by anyone other than an authorized
service representative of VTech; or
3. Product to the extent that the problem experienced is
caused by signal conditions, network reliability, or cable or
antenna systems; or
4. Product to the extent that the problem is caused by use
with non-VTech accessories; or
5. Product whose warranty/quality stickers, product serial
number plates or electronic serial numbers have been
removed, altered or rendered illegible; or
6. Product purchased, used, serviced, or shipped for repair
from outside the United States of America or Canada, or
used for commercial or institutional purposes (including
but not limited to Products used for rental purposes); or
7. Product returned without a valid proof of purchase (see
item 2 below); or
8. Charges for installation or set up, adjustment of customer
controls, and installation or repair of systems outside the
unit.
How do you get warranty service?
To obtain warranty service in the USA, please visit our
website at www.vtechphones.com or call 1 (800) 595-
9511. In Canada, go to www.vtechcanada.com or call
1 (800) 267-7377.
NOTE: Before calling for service, please review the user’s
manual - a check of the Product’s controls and features may
save you a service call.
Except as provided by applicable law, you assume the risk
of loss or damage during transit and transportation and are
responsible for delivery or handling charges incurred in the
transport of the Product(s) to the service location. VTech
will return replaced Product under this limited warranty.
Transportation, delivery or handling charges are prepaid.
VTech assumes no risk for damage or loss of the Product in
transit.
What must you return with the Product to get warranty
service?
1. Return the entire original package and contents
including the Product to the VTech service location along
with a description of the malfunction or difficulty; and
2. Include a “valid proof of purchase” (sales receipt)
identifying the Product purchased (Product model) and
the date of purchase or receipt; and
3. Provide your name, complete and correct mailing
address, and telephone number.
Other limitations
This warranty is the complete and exclusive agreement
between you and VTech. It supersedes all other written or
oral communications related to this Product. VTech provides
no other warranties for this Product. The warranty exclusively
describes all of VTech’s responsibilities regarding the
Product. There are no other express warranties. No one is
authorized to make modifications to this limited warranty and
you should not rely on any such modification. State/Provincial
Law Rights: This warranty gives you specific legal rights, and
you may also have other rights, which vary from state to state
or province to province.
Limitations: Implied warranties, including those of fitness
for a particular purpose and merchantability (an unwritten
warranty that the Product is fit for ordinary use) are limited
to one year from the date of purchase. Some states/
provinces do not allow limitations on how long an implied
warranty lasts, so the above limitation may not apply to you.
In no event shall VTech be liable for any indirect, special,
incidental, consequential, or similar damages (including,
but not limited to lost profits or revenue, inability to use
the Product or other associated equipment, the cost of
substitute equipment, and claims by third parties) resulting
from the use of this Product. Some states/provinces
do not allow the exclusion or limitation of incidental
or consequential damages, so the above limitation or
exclusion may not apply to you.
Please retain your original sales receipt as proof
of purchase.
Limited warranty
The RBRC seal on the lithium-ion battery indicates that VTech Communications, Inc. is voluntarily participating in an
industry program to collect and recycle these batteries at the end of their useful lives, when taken out of service within
the United States and Canada. The program provides a convenient alternative to placing used lithium-ion batteries into
the trash or municipal waste, which may be illegal in your area.
VTech’s participation makes it easy for you to drop off the spent product at local retailers participating in the program
or at authorized VTech product service centers. Please call 1 (800) 8 BATTERY® for information on Li-ion battery recycling and disposal
bans/restrictions in your area. VTech’s involvement in this program is part of its commitment to protecting our environment and
conserving natural resources.
The RBRC Seal and 1 (800) 8 BATTERY® are registered trademarks of Call2recycle, Inc.
The RBRC seal
For RM7868-2HD only
Monitoring Modes
When more than one baby unit is paired to the parent unit, you can choose to view
different baby units in three monitoring modes. Learn more about each below:
Change the monitoring mode:
1. Press MENU when the parent unit is idle.
2. Press MENU or to enter Monitoring Mode menu.
3. Press or to choose between Single , Split , and Patrol monitoring
mode options. Press SELECT to confirm.
On the baby unit:
Night Light
Single Mode
The screen displays images only from the selected baby
unit in full screen.
Split Mode The screen displays images from all paired baby units at
the same time in split view.
Patrol Mode The screen displays a single cam view that transitions to a
different baby unit every 10 seconds.
2. Adjust the angle of the baby unit to aim
at your baby.
1. Place the baby unit more than 3 feet away
from your baby.
3. To avoid causing feedback noise from your baby monitor:
Make sure your baby unit and parent unit are more than 3 feet apart; OR
Turn down the volume of your parent unit.
Positioning the baby monitor
Keep the baby unit out of the reach of your baby. Never place or mount the baby unit inside the baby’s
crib or playpen.
You can control the night light remotely on the parent unit or directly on the baby unit.
On the parent unit:
1. Press MENU.
2. Press or to scroll to Night Light
menu, then press MENU or to enter.
3. Press or to choose below options:
Night Light Control Key
Single Tap: Turn on/off
Tap and hold: Adjust night light brightness
Turn on/off night light
Change night light color
Adjust night light brightness
Set night light timer
  • Page 1 1
  • Page 2 2

VTech RM7868HD Guide de démarrage rapide

Catégorie
Moniteurs vidéo bébé
Taper
Guide de démarrage rapide

dans d''autres langues