Toro eTimeCutter 42in Riding Mower Manuel utilisateur

Form No. 3463-573 Rev A

eT imeCutter

®

42in or 54in Riding Mower

75841 , 75851

Cortacésped de asiento eT imeCutter

®

de 107 o 137

cm (42" o 54")

75841 , 75851

T ondeuse autoportée eT imeCutter

®

de 107 cm ou

137 cm (42 po ou 54 po)

75841 , 75851

www .T oro.com.

*3463-573*

Operator’s Manual

eTimeCutter® 42in or 54in Riding Mower

Model—Serial Range

75841—400000000 and Up

75851—400000000 and Up

3463-565A Original Instructions (EN) *3463-565*A

Disclaimers and Regulatory Information

WARNING

CALIFORNIA

Proposition 65

The power cord on this product contains lead, a chemical known to the State of California to

cause birth defects or other reproductive harm. Wash hands after handling.

Use of this product may cause exposure to chemicals known to the State of California to cause

cancer, birth defects, or other reproductive harm.

Table of Contents

Chapter 1: Introduction........................................................................................................................ 1–1

Intended Use ..................................................................................................................................... 1–1

Getting Help....................................................................................................................................... 1–1

Chapter 2: Safety.................................................................................................................................. 2–1

General Machine Safety Warnings .............................................................................................. 2–1

Lawn Mower Safety Warnings....................................................................................................... 2–3

Additional Safety Messages .......................................................................................................... 2–5

Safety-Alert Symbol ..................................................................................................................... 2–5

General Safety .............................................................................................................................. 2–5

Slope Indicator .................................................................................................................................. 2–6

Safety and Instructional Decals .................................................................................................... 2–7

Chapter 3: Product Overview ............................................................................................................ 3–1

Control Panel..................................................................................................................................... 3–2

Parking Brake.................................................................................................................................... 3–5

Motion-Control Levers..................................................................................................................... 3–5

MyRide® Suspension Adjustment Lever.................................................................................... 3–5

Specifications .................................................................................................................................... 3–6

Chapter 4: Operation ........................................................................................................................... 4–1

Before Operation .............................................................................................................................. 4–1

Before Operation Safety ............................................................................................................. 4–1

Installing the Battery Packs........................................................................................................ 4–2

Performing Daily Maintenance .................................................................................................. 4–2

Safety-Interlock System.............................................................................................................. 4–3

Positioning the Seat ..................................................................................................................... 4–4

Adjusting the Motion-Control Lever Height ............................................................................ 4–5

Adjusting the Motion-Control Lever Tilt ................................................................................... 4–6

During Operation .............................................................................................................................. 4–6

During Operation Safety ............................................................................................................. 4–6

Starting the Machine.................................................................................................................... 4–8

Shutting Off the Machine ............................................................................................................ 4–8

Operating the Parking Brake ..................................................................................................... 4–9

Driving the Machine ................................................................................................................... 4–10

Operating the Mower Blade-Control Switch (PTO) ............................................................ 4–12

Side Discharge............................................................................................................................ 4–13

8111 Lyndale Ave So

Bloomington, MN 55044

Contact us at www.Toro.com

Printed in the USA

Adjusting the Height of Cut....................................................................................................... 4–13

Adjusting the Anti-Scalp Rollers.............................................................................................. 4–14

Operating Tips............................................................................................................................. 4–14

After Operation................................................................................................................................ 4–16

After Operation Safety............................................................................................................... 4–16

Charging the Battery Packs ..................................................................................................... 4–16

Hauling the Machine .................................................................................................................. 4–18

Chapter 5: Maintenance ..................................................................................................................... 5–1

Maintenance Safety ......................................................................................................................... 5–1

Recommended Maintenance Schedule...................................................................................... 5–2

Pre-Maintenance Procedures ....................................................................................................... 5–2

Moving a Non-Functioning Machine ........................................................................................ 5–2

Raising the Machine .................................................................................................................... 5–3

Electrical System Maintenance..................................................................................................... 5–4

Preparing the Battery Pack for Recycling............................................................................... 5–4

Checking the Battery-Box Filter ................................................................................................ 5–4

Drive System Maintenance ............................................................................................................ 5–5

Checking the Tire Pressure........................................................................................................ 5–5

Checking the Wheel Lug Nuts................................................................................................... 5–5

Adjusting the Tracking................................................................................................................. 5–5

Mower-Deck Maintenance ............................................................................................................. 5–7

Blade Service ................................................................................................................................ 5–7

Leveling the Mower Deck ......................................................................................................... 5–10

Brake Maintenance ........................................................................................................................ 5–14

Testing the Parking Brake ........................................................................................................ 5–14

Cleaning............................................................................................................................................ 5–15

Cleaning Under the Mower Deck............................................................................................ 5–15

Chapter 6: Storage............................................................................................................................... 6–1

Storing the Machine......................................................................................................................... 6–1

Chapter 7: Troubleshooting ............................................................................................................... 7–1

Machine Troubleshooting ............................................................................................................... 7–1

Battery and Charger Troubleshooting ......................................................................................... 7–2

Display Error and Fault Code Troubleshooting ......................................................................... 7–4

Chapter 8: Schematic: Electrical Diagram...................................................................................... 8–1

California Proposition 65 Warning Information

3463-565 A :

Chapter 1

Introduction

Intended Use

This rotary-blade, riding lawn mower is intended to be used by homeowners in residential

applications. It is designed primarily for cutting grass on well-maintained lawns. Using this

product for purposes other than its intended use could prove dangerous to you and

bystanders.

Read this information carefully to learn how to operate and maintain your product properly

and to avoid injury and product damage. You are responsible for operating the product

properly and safely.

Getting Help

G444734

Visit www.Toro.com for product safety and

operation training materials, accessory

information, help finding a dealer, or to register

your product.

Whenever you need service, genuine Toro parts,

or additional information, contact an Authorized

Service Dealer or Toro Customer Service and have

the model and serial numbers of your product

ready. These numbers are located on the serial

plate on your product . Write the numbers in the

space provided.

IMPORTANT

With your mobile device, you can scan the QR code on the serial number decal (if

equipped) to access warranty, parts, and other product information.

Model

Number:

Serial

Number:

Introduction Page 1–1 3463-565 A

Chapter 2

Safety

General Machine Safety Warnings

WARNING—Read all safety warnings, instructions, illustrations and

specifications provided with this machine.

Failure to follow the warnings and instructions may result in electric shock, fire and/

or serious injury.

The term “machine” in all of the warnings listed below refers to your mains-operated

(corded) machine or battery-operated (cordless) machine.

1. Work area safety

A. Keep work area clean and well lit. Cluttered or dark areas invite accidents.

B. Do not operate the machine in explosive atmospheres, such as in the

presence of flammable liquids, gasses, or dust. The machine creates sparks,

which may ignite the dust or fumes.

C. Keep children and bystanders away while operating the machine. Distractions

can cause you to lose control.

2. Electrical safety

A. Machine plugs must match the outlet. Never modify the plug in any way. Do

not use any adapter plugs with an earthed (grounded) machine. Unmodified

plugs and matching outlets will reduce risk of electric shock.

B. Avoid body contact with earthed or grounded surfaces, such as pipes,

radiators, ranges, and refrigerators. There is an increased risk of electric shock if

your body is earthed or grounded.

C. Do not expose the machine to rain or wet conditions. Water entering a machine

will increase the risk of electric shock.

D. Do not abuse the cord. Never use the cord for carrying, pulling or unplugging

the machine. Keep cord away from heat, oil, sharp edges, or moving parts.

Damaged or entangled cords increase the risk of electric shock.

E. When operating the machine outdoors, use an extension cord suitable for

outdoor use. Use of a cord suitable for outdoor use reduces the risk of electric

shock.

F. If operating the machine in a damp location is unavoidable, use a residual

current device (RCD) protected supply. Use of an RCD reduces the risk of

electric shock.

3463-565 A Page 2–1 Safety

3. Personal safety

A. Stay alert, watch what you are doing, and use common sense when operating

the machine. Do not use the machine while you are tired or under the

influence of drugs, alcohol, or medication. A moment of inattention while

operating the machine may result in serious personal injury.

B. Use personal protective equipment. Always wear eye protection. Protective

equipment such as a dust mask, non-skid safety shoes, or hearing protection used

for appropriate conditions will reduce personal injuries.

C. Prevent unintentional starting. Ensure the switch is in the off-position before

connecting to power source and/or battery pack. Energising a machine that has

the switch on invites accidents.

D. Remove any adjusting key or wrench before turning the machine on. A wrench

or a key left attached to a rotating part of the machine may result in personal injury.

E. Do not overreach. Keep proper footing and balance at all times. This enables

better control of the machine in unexpected situations.

F. Dress properly. Do not wear loose clothing or jewelry. Keep your hair and

clothing away from moving parts. Loose clothes, jewelry or long hair can be

caught in moving parts.

G. If devices are provided for the connection of dust extraction and collection

facilities, ensure these are connected and properly used. Use of dust collection

can reduce dust-related hazards.

H. Do not let familiarity gained from frequent use of the machine allow you to

become complacent and ignore machine safety principles. A careless action

can cause severe injury within a fraction of a second.

4. Machine use and care

A. Do not force the machine. Use the correct machine for your application. The

correct machine will do the job better and safer at the rate for which it was designed.

B. Do not use the machine if the switch does not turn it on and off. Any machine

that cannot be controlled with the switch is dangerous and must be repaired.

C. Disconnect the plug from the power source and/or remove the battery pack, if

detachable, from the machine before making any adjustments, changing

accessories, or storing the machine. Such preventive safety measures reduce

the risk of starting the machine accidentally.

D. Store an idle machine out of the reach of children and do not allow persons

unfamiliar with the machine or these instructions to operate the machine. A

machine is dangerous in the hands of untrained users.

E. Maintain the machine and accessories. Check for misalignment or binding of

moving parts, breakage of parts and any other condition that may affect the

operation of the machine. If damaged, have the machine repaired before use.

Many accidents are caused by a poorly maintained machine.

F. Keep cutting tools sharp and clean. Properly maintained cutting tools with sharp

cutting edges are less likely to bind and are easier to control.

G. Use the machine, accessories, and tool bits etc., in accordance with these

instructions, taking into account the working conditions and the work to be

Safety: General Machine Safety Warnings Page 2–2 3463-565 A

performed. Use of the machine for operations different from those intended could

result in a hazardous situation.

H. Keep handles and grasping surfaces dry, clean and free from oil and grease.

Slippery handles and grasping surfaces do not allow for safe handling and control of

the machine in unexpected situations.

5. Battery machine use and care

A. Recharge only with the charger specified by a manufacturer. A charger that is

suitable for one type of battery pack may create a risk of fire when used with another

battery pack.

B. Use the machine only with specifically designated batteries. Use of any other

batteries may create a risk of injury and fire.

C. When battery pack is not in use, keep it away from other metal objects, like

paper clips, coins, keys, nails, screws or other small metal objects, that can

make a connection from one terminal to another. Shorting the battery terminals

together may cause burns or a fire.

D. Under abusive conditions, liquid may be ejected from the battery; avoid

contact. If contact accidentally occurs, flush with water. If liquid contacts

eyes, additionally seek medical help. Liquid ejected from the battery may cause

irritation or burns.

E. Do not use a battery pack or machine that is damaged or modified. Damaged

or modified batteries may exhibit unpredictable behavior resulting in fire, explosion

or risk or injury.

F. Do not expose a battery pack or machine to fire or excessive temperature.

Exposure to fire temperature above 130°C (265°F) may cause an explosion.

G. Follow all charging instructions and do not charge the battery pack or

machine outside the temperature range specified in the instructions. Charging

improperly or at temperatures outside the specified range may damage the battery

and increase the risk of fire.

6. Service

A. Have your machine serviced by a qualified repair person using only identical

replacement parts. This will ensure that the safety of the machine is maintained.

B. Never service damaged battery packs. Service of battery packs should be

performed only by the manufacturer or authorized service providers.

Lawn Mower Safety Warnings

A. Do not use the lawnmower in bad weather conditions, especially when there is a

risk of lightning. This decreases the risk of being struck by lightning.

B. Thoroughly inspect the area for wildlife where the lawnmower is to be used.

Wildlife may be injured by the lawnmower during operation.

C. Thoroughly inspect the area where the lawnmower is to be used and remove all

stones, sticks, wires, bones, and other foreign objects. Thrown objects can cause

personal injury.

3463-565A Page 2–3 Safety: Lawn Mower Safety Warnings

D. Before using the lawnmower, always visually inspect to see that the blade and the

blade assembly are not worn or damaged. Worn or damaged parts increase the risk

of injury.

E. Keep guards in place. Guards must be in working order and be properly mounted.

A guard that is loose, damaged, or is not functioning correctly may result in personal

injury.

F. Keep all cooling air inlets clear of debris. Blocked air inlets and debris may result in

overheating or risk of fire.

G. While operating the lawnmower, always wear non-slip and protective footwear. Do

not operate the lawnmower when barefoot or wearing open sandals. This reduces

the chance of injury to the feet from contact with the moving blade.

H. While operating the lawnmower, always wear long trousers. Exposed skin

increases the likelihood of injury from thrown objects.

I. Do not operate the lawnmower on slopes greater than 15°. This reduces the risk of

loss of control, slipping, and rollover which may result in personal injury.

J. Exercise extreme caution when working on slopes. This reduces the risk of loss of

control, slipping, and rollover which may result in personal injury.

K. Use extreme caution when reversing the lawnmower. Always be aware of your

surroundings.

L. Do not touch blades and other hazardous moving parts while they are still in

motion. This reduces the risk of injury from moving parts.

M. When clearing jammed material or cleaning the lawn mower, make sure all power

switches are off, and remove the key. Unexpected operation of the lawn mower may

result in serious personal injury.

Save all warnings and instructions for future reference.

Safety: Lawn Mower Safety Warnings Page 2–4 3463-565 A

Additional Safety Messages

Safety-Alert Symbol

The safety-alert symbol shown in this manual and on the machine identifies important safety

messages that you must follow to prevent accidents.

G405934

DANGER indicates an imminently hazardous situation which, if not avoided, will result in

death or serious injury.

WARNING indicates a potentially hazardous situation which, if not avoided, could result in

death or serious injury.

CAUTION indicates a potentially hazardous situation which, if not avoided, may result in

minor or moderate injury.

This manual uses 2 other words to highlight information. Important calls attention to special

mechanical information and Note emphasizes general information worthy of special

attention.

General Safety

This product is capable of amputating hands and feet and of throwing objects. Always follow

all safety instructions to avoid serious personal injury or death.

• Keep clear of the discharge opening.

• Allow only responsible and physically capable people to operate the machine.

• Shut off the machine, remove the key, and wait for all moving parts to stop before leaving

the operator's position. Allow the machine to cool before servicing, adjusting, or cleaning

it.

3463-565A Page 2–5 Safety: Additional Safety Messages

Slope Indicator

You may copy this page for personal use.

G011841s

The maximum slope you can operate the machine on is 15 degrees. Use the slope chart to determine the degree

of slope of hills before operating. Do not operate this machine on a slope greater than 15 degrees. Fold along

the appropriate line to match the recommended slope.

Align this edge with a vertical surface, a tree, building, fence pole, etc.

Example of how to compare slope with folded edge

Safety: Slope Indicator Page 2–6 3463-565 A

Safety and Instructional Decals

Safety decals and instructions are easily visible to the operator and are located near any area

of potential danger. Replace any decal that is damaged or missing.

Decal Part: 130-0731

s_decal130-0731

Warning—thrown object hazard;

keep the deflector in place.

Cutting hazard of hand or foot,

mower blade—keep away from moving

parts.

Decal Part: 133-8061

s_decal133-8061

Decal Part: 137-8127

s_decal137-8127

Attention—do not spray with high-

pressure water.

Decal Part: 139-1271

s_decal139-1271

Parking brake—Engage

Parking brake—Disengage

3463-565A Page 2–7 Safety: Safety and Instructional Decals

Decal Part: 139-2397

MyRIDE models only

s_decal139-2397

Decal Part: 145-3802

s_decal145-3802

The battery pack is charging.

The battery pack is fully charged.

The battery pack charging is on standby while

other batteries charge (charging mode

dependent).

The battery pack is over or under the appropriate

temperature range.

Battery pack charging fault.

Decal Part: 145-8263

decal145-8263

Read the Operator’s Manual.

Recycle the battery.

Do not dispose improperly.

Keep away from open fire or

flames.

Do not expose to rain.

Decal Part: 145-8265

decal145-8265

Battery charging status

Safety: Safety and Instructional Decals Page 2–8 3463-565 A

Decal Part: 145-8275

s_decal145-8275

Serial charging mode—one battery

charges fully at a time (other batteries

remain on standby).

Parallel charging mode—all

batteries are charged to the same level.

Decal Part: 147-0290

decal147-0290

Warning—light is bright; do not look

directly into the light.

Decal Part: 147-7614

decal147-7614

Blade control—fast

Traction drive—fast

Blade control—slow

Traction drive—slow

Off

On

3463-565A Page 2–9 Safety: Safety and Instructional Decals

Decal Part: 147-7615

decal147-7615

Thrown object hazard—keep

bystanders away.

Thrown object hazard, mower—do

not operate without the deflector,

discharge cover, or grass collection

system in place.

Cutting/dismemberment hazard of

hand or foot, mower blade—keep away

from moving parts.

Decal Part: 147-7616

MyRIDE models only

decal147-7616

Note: This machine complies with the industry standard stability test in the static lateral and

longitudinal tests with the maximum recommended slope indicated on the decal. Review the

instructions for operating the machine on slopes in the Operator’s Manual as well as the

conditions in which you would operate the machine to determine whether you can operate

the machine in the conditions on that day and at that site. Changes in the terrain can result

in a change in slope operation for the machine.

Warning—read the Operator’s Manual.

Warning—before performing maintenance, engage the parking brake and remove the key.

Cutting/dismemberment hazard of hand—keep away from moving parts; keep all guards and shields in place.

Thrown object hazard—keep bystanders away; pick up debris; keep the deflector in place.

Tipping hazard—do not use dual ramps when loading onto a trailer; use 1 ramp wide enough for the machine;

use a ramp with an incline less than 15°; back up the ramp when loading the machine and drive forward off the

ramp when unloading.

Runover hazard—do not carry passengers; look down and behind you when moving in reverse.

Tipping hazard—do not use the machine near drop-offs with slopes greater than 15°; only operate across slopes

less than 15°.

Safety: Safety and Instructional Decals Page 2–10 3463-565 A

Decal Part: 147-7617

Non-MyRIDE models only

s_decal147-7617

Note: This machine complies with the industry standard stability test in the static lateral and

longitudinal tests with the maximum recommended slope indicated on the decal. Review the

instructions for operating the machine on slopes in the Operator’s Manual as well as the

conditions in which you would operate the machine to determine whether you can operate

the machine in the conditions on that day and at that site. Changes in the terrain can result

in a change in slope operation for the machine.

Warning—read the Operator’s Manual.

Warning—before performing maintenance, engage the parking brake and remove the key.

Cutting/dismemberment hazard of hand—keep away from moving parts; keep all guards and shields in place.

Thrown object hazard—keep bystanders away; pick up debris; keep the deflector in place.

Tipping hazard—do not use dual ramps when loading onto a trailer; use 1 ramp wide enough for the machine;

use a ramp with an incline less than 15°; back up the ramp when loading the machine and drive forward off the

ramp when unloading.

Runover hazard—do not carry passengers; look down and behind you when moving in reverse.

Tipping hazard—do not use the machine near drop-offs with slopes greater than 15°; only operate across slopes

less than 15°.

3463-565A Page 2–11 Safety: Safety and Instructional Decals

Decal Part: 147-7619

decal147-7619

Fast

Slow

Neutral

Reverse

Traction controls

Decal Part: 147-7620

decal147-7620

Fast

Slow

Neutral

Reverse

Traction controls

Safety: Safety and Instructional Decals Page 2–12 3463-565 A

Decal Part: 147-7621

decal147-7621

Read the Operator’s Manual.

Full function

Limited function

No function/extremely limited

function

3463-565A Page 2–13 Safety: Safety and Instructional Decals

Chapter 3

Product Overview

G427499

MyRide® suspension adjustment

lever

Battery box

Motion-control lever

Parking brake

Caster wheel

Anti-scalp roller

Height-of-cut lever

Grass deflector

Control panel

G448680

Battery charger

Battery pack (4 included)

Product Overview Page 3–1 3463-565 A

La page charge ...

Toro eTimeCutter 42in Riding Mower Manuel utilisateur

Ce manuel convient également à

Toro eTimeCutter 42in Riding Mower Manuel utilisateur

dans d''autres langues

Documents connexes

Autres documents