Toro TimeCutter Max 54in Zero Turn Riding Mower Manuel utilisateur

Form No. 3466-520 Rev A

T imeCutter

®

Max or MyRIDE 54in or 60in Zero T urn

Riding Mower

77503 , 77504 , 77506 , 77507 , 77601 , 77603

Cortacésped giro cero de asiento T imeCutter

®

Max o

MyRIDE de 137 cm (54") o 152 cm (60")

77503 , 77504 , 77506 , 77507 , 77601 , 77603

T ondeuse autoportée à rayon de braquage zéro

T imeCutter

®

Max ou MyRIDE de137 cm ou 152 cm (54

po ou 60 po)

77503 , 77504 , 77506 , 77507 , 77601 , 77603

www .T oro.com.

*3466-520*

Operator’s Manual

TimeCutter® Max or MyRIDE 54in or 60in

Zero Turn Riding Mower

Model—Serial Range

77503—400000000 and Up

77504—400000000 and Up

77506—400000000 and Up

77507—400000000 and Up

77601—400000000 and Up

77603—400000000 and Up

3466-517A Original Instructions (EN) *3466-517*A

Disclaimers and Regulatory Information

It is a violation of California Public Resource Code Section 4442 or 4443 to use or operate

the engine on any forest-covered, brush-covered, or grass-covered land unless the engine

is equipped with a spark arrester, as defined in Section 4442, maintained in effective

working order or the engine is constructed, equipped, and maintained for the prevention of

fire.

Gross or Net Torque: The gross or net torque of this engine was laboratory rated by the

engine manufacturer in accordance with the Society of Automotive Engineers (SAE) J1940

or J2723. As configured to meet safety, emission, and operating requirements, the actual

engine torque on this class of mower will be significantly lower. Please refer to the engine

manufacturer’s information included with the machine.

The enclosed engine owner's manual is supplied for information regarding the US

Environmental Protection Agency (EPA) and the California Emission Control Regulation of

emission systems, maintenance, and warranty. Replacements may be ordered through the

engine manufacturer.

WARNING

CALIFORNIA

Proposition 65

The engine exhaust from this product contains chemicals known to the State of California to

cause cancer, birth defects, or other reproductive harm.

Battery posts, terminals, and related accessories contain lead and lead compounds, chemicals

known to the State of California to cause cancer and reproductive harm. Wash hands after

handling.

Use of this product may cause exposure to chemicals known to the State of California to cause

cancer, birth defects, or other reproductive harm.

Table of Contents

Chapter 1: Introduction........................................................................................................................ 1–1

Intended Use ..................................................................................................................................... 1–1

Getting Help....................................................................................................................................... 1–1

Manual Conventions........................................................................................................................ 1–2

Safety Alert Classifications......................................................................................................... 1–2

Chapter 2: Safety.................................................................................................................................. 2–1

General Safety .................................................................................................................................. 2–1

Slope Indicator .................................................................................................................................. 2–2

Safety and Instructional Decals .................................................................................................... 2–3

Chapter 3: Product Overview ............................................................................................................ 3–1

Control Panel..................................................................................................................................... 3–2

Motion-Control Levers..................................................................................................................... 3–3

Park Position ................................................................................................................................. 3–3

MyRide® Suspension Adjustment Lever.................................................................................... 3–4

8111 Lyndale Ave So

Bloomington, MN 55044

Contact us at www.Toro.com

Printed in Mexico

Height-of-Cut Pin.............................................................................................................................. 3–4

Deck-Lift Pedal.................................................................................................................................. 3–4

Specifications .................................................................................................................................... 3–4

Chapter 4: Operation ........................................................................................................................... 4–1

Before Operation .............................................................................................................................. 4–1

Before Operation Safety ............................................................................................................. 4–1

Fuel .................................................................................................................................................. 4–3

Performing Daily Maintenance .................................................................................................. 4–3

Break-In Time ................................................................................................................................ 4–4

Safety-Interlock System.............................................................................................................. 4–4

Positioning the Seat ..................................................................................................................... 4–5

Adjusting the Motion-Control Lever Height ............................................................................ 4–6

Adjusting the Motion-Control Lever Tilt ................................................................................... 4–7

During Operation .............................................................................................................................. 4–7

During Operation Safety ............................................................................................................. 4–7

Starting the Engine..................................................................................................................... 4–10

Shutting Off the Engine ............................................................................................................. 4–11

Driving the Machine ................................................................................................................... 4–12

Operating the Mower Blade-Control Switch (PTO) ............................................................ 4–13

Side Discharge............................................................................................................................ 4–14

Adjusting the Height of Cut....................................................................................................... 4–15

Adjusting the Anti-Scalp Rollers.............................................................................................. 4–15

Operating Tips............................................................................................................................. 4–15

After Operation................................................................................................................................ 4–17

After Operation Safety............................................................................................................... 4–17

Cleaning the Machine................................................................................................................ 4–17

Hauling the Machine .................................................................................................................. 4–17

Chapter 5: Maintenance ..................................................................................................................... 5–1

Maintenance Safety ......................................................................................................................... 5–1

Recommended Maintenance Schedule...................................................................................... 5–2

Pre-Maintenance Procedures ....................................................................................................... 5–3

Moving a Non-Functioning Machine ........................................................................................ 5–3

Raising the Machine .................................................................................................................... 5–4

Lubrication.......................................................................................................................................... 5–5

Greasing the Bearings ................................................................................................................ 5–5

Engine Maintenance........................................................................................................................ 5–6

Engine Safety ................................................................................................................................ 5–6

Air Cleaner Service ...................................................................................................................... 5–6

Engine-Oil Service ....................................................................................................................... 5–7

Servicing the Spark Plug .......................................................................................................... 5–11

Cleaning the Cooling System .................................................................................................. 5–12

Fuel Maintenance........................................................................................................................... 5–13

Replacing the Fuel Filter........................................................................................................... 5–13

Electrical System Maintenance................................................................................................... 5–14

Electrical System Safety........................................................................................................... 5–14

Battery Service............................................................................................................................ 5–14

Jump-Starting the Machine ...................................................................................................... 5–18

Servicing the Fuses ................................................................................................................... 5–20

Drive System Maintenance .......................................................................................................... 5–20

Checking the Tire Pressure...................................................................................................... 5–20

Checking the Wheel Lug Nuts................................................................................................. 5–21

Adjusting the Tracking............................................................................................................... 5–21

Belt Maintenance............................................................................................................................ 5–22

3466-517 A :

Inspecting the Belts.................................................................................................................... 5–22

Replacing the Mower Belt......................................................................................................... 5–22

Mower-Deck Maintenance ........................................................................................................... 5–25

Blade Safety ................................................................................................................................ 5–25

Blade Service .............................................................................................................................. 5–25

Leveling the Mower Deck ......................................................................................................... 5–28

Removing the Mower Deck...................................................................................................... 5–30

Installing the Mower Deck ........................................................................................................ 5–31

Replacing the Grass Deflector ................................................................................................ 5–31

Cleaning............................................................................................................................................ 5–32

Washing the Underside of the Mower Deck......................................................................... 5–32

Disposing of Waste .................................................................................................................... 5–33

Chapter 6: Storage............................................................................................................................... 6–1

Storage Safety .................................................................................................................................. 6–1

Preparing the Machine for Storage Over 30 Days.................................................................... 6–1

Storing the Battery............................................................................................................................ 6–3

Battery Storage Tips .................................................................................................................... 6–3

Chapter 7: Troubleshooting ............................................................................................................... 7–1

Chapter 8: Schematics........................................................................................................................ 8–1

Electrical Diagram ............................................................................................................................ 8–1

California Proposition 65 Warning Information

: Page 4 3466-517 A

Chapter 1

Introduction

Intended Use

This rotary-blade, riding lawn mower is intended to be used by homeowners in residential

applications. It is designed primarily for cutting grass on well-maintained lawns. Using this

product for purposes other than its intended use could prove dangerous to you and

bystanders.

Read this information carefully to learn how to operate and maintain your product properly

and to avoid injury and product damage. You are responsible for operating the product

properly and safely.

Getting Help

G451770

Visit www.Toro.com for product safety and

operation training materials, accessory

information, help finding a dealer, or to register

your product.

Whenever you need service, genuine Toro parts,

or additional information, contact an Authorized

Service Dealer or Toro Customer Service and have

the model and serial numbers of your product

ready. These numbers are located on the serial

plate on your product . Write the numbers in the

space provided.

IMPORTANT

With your mobile device, you can scan the QR code on the serial number decal (if

equipped) to access warranty, parts, and other product information.

Model

Number:

Serial

Number:

3466-517 A Page 1–1 Introduction

Manual Conventions

This manual identifies potential hazards and has safety messages identified by the safety-

alert symbol, which signals a hazard that may cause serious injury or death if you do not

follow the recommended precautions.

G405934

This manual uses 2 words to highlight information. Important calls attention to special

mechanical information and Note emphasizes general information worthy of special

attention.

Safety Alert Classifications

The safety-alert symbol shown in this manual and on the machine identifies important safety

messages that you must follow to prevent accidents.

Safety-alert symbol appears above information that alerts you to unsafe actions or situations

and is followed by the word DANGER,WARNING, or CAUTION.

DANGER

Danger indicates an imminently hazardous situation which, if not avoided, will result

in death or serious injury.

WARNING

Warning indicates a potentially hazardous situation which, if not avoided, could result

in death or serious injury.

CAUTION

Caution indicates a potentially hazardous situation which, if not avoided, may result

in minor or moderate injury.

Introduction: Manual Conventions Page 1–2 3466-517 A

Chapter 2

Safety

General Safety

This product is capable of amputating hands and feet and of throwing objects. Always follow

all safety instructions to avoid serious personal injury or death.

• Read, understand, and follow the instructions and warnings in this Operator’s Manual

and on the machine, engine, and attachments before starting the engine.

• Do not allow children or untrained people to operate or service the machine. Allow only

people who are responsible, trained, familiar with the instructions, and physically capable

to operate or service the machine.

• Keep bystanders, particularly children, away from the operating area.

• Do not operate the machine near drop-offs, ditches, embankments, water, or other

hazards, or on slopes greater than 15°.

• Do not put your hands or feet near moving parts.

• Do not operate the machine without all safety shields, guards, switches, and other

devices in place and working properly.

• Park the machine on a level surface, disengage the drives, engage the parking brake,

shut off the engine, remove the key, and wait for all moving parts to stop before leaving

the operator’s position.

• Wait for the machine to cool before servicing, adjusting, fueling, cleaning, or storing it.

3466-517 A Page 2–1 Safety

Slope Indicator

You may copy this page for personal use.

G011841s

The maximum slope you can operate the machine on is 15 degrees. Use the slope chart to determine the degree

of slope of hills before operating. Do not operate this machine on a slope greater than 15 degrees. Fold along

the appropriate line to match the recommended slope.

Align this edge with a vertical surface, a tree, building, fence pole, etc.

Example of how to compare slope with folded edge

Safety: Slope Indicator Page 2–2 3466-517 A

Safety and Instructional Decals

Safety decals and instructions are easily visible to the operator and are located near any area

of potential danger. Replace any decal that is damaged or missing.

Decal Part: 99-3943

Models 77503, 77504, and 77601 only

s_decal99-3943

Belt routing

Engine

Decal Part: 112-9840

s_decal112-9840

Read the Operator's Manual.

Height of cut

Remove the ignition key and read

the instructions before servicing or

performing maintenance.

Decal Part: 130-0731

Models 77503, 77504, and 77601 only

s_decal130-0731

Warning—thrown object hazard;

keep the deflector in place.

Cutting hazard of hand or foot,

mower blade—keep away from moving

parts.

3466-517A Page 2–3 Safety: Safety and Instructional Decals

Decal Part: 132-0872

Models 77503, 77504, and 77601 only

s_decal132-0872

Thrown object hazard—keep

bystanders away.

Thrown object hazard, mower—do

not operate the machine with an open

deck; use a bagger or a deflector.

Cutting/dismemberment hazard of

hands or feet, mower blade—stay away

from moving parts.

Entanglement hazard of hands,

belt—stay away from moving parts;

keep all guards and shields in place.

Decal Part: 139-2394

s_decal139-2394

Traction controls

Fast

Slow

Neutral

Reverse

Parking brake

Decal Part: 139-2395

s_decal139-2395

Parking brake

Fast

Slow

Neutral

Reverse

Traction controls

Decal Part: 142-5864

decal142-5864

Safety: Safety and Instructional Decals Page 2–4 3466-517 A

Decal Part: 144-5288

s_decal144-5288

Warning—read the Operator’s

Manual.

Cutting/dismemberment hazard of

the fingers or hand—keep hands away

from moving parts; keep all guards and

shields in place.

Thrown object hazard—keep

bystanders away; pick up debris; keep

the deflector in place.

Runover hazard—do not carry

passengers; look behind you and down

when moving in reverse.

Tipping hazard—when loading onto

a trailer, do not use dual ramps; only

use a singular ramp wide enough for the

machine; do not use a ramp with a

slope greater than 15°; back up the

ramp (in reverse) and drive forward off

the ramp.

Tipping hazard—do not use the

machine near drop-offs with slopes

greater than 15°; only operate across

slopes less than 15°.

Note: This machine complies with the industry standard stability test in the static lateral and

longitudinal tests with the maximum recommended slope indicated on the decal. Review the

instructions for operating the machine on slopes in the Operator’s Manual as well as the

conditions in which you would operate the machine to determine whether you can operate

the machine in the conditions on that day and at that site. Changes in the terrain can result

in a change in slope operation for the machine.

Decal Part: 147-2399

s_decal147-2399

Read the Operator’s Manual.

Warning—Fill to bottom of filler

neck; warning–do not overfill the tank.

3466-517A Page 2–5 Safety: Safety and Instructional Decals

Decal Part: 147-2866

decal147-2866

Height of cut

Decal Part: 147-3023

Models 77506, 77507, and 77603 only

s_decal147-3023

Warning—thrown object hazard;

keep the deflector shield in place.

Cutting hazard of hand or foot,

mower blade—keep away from moving

parts.

Safety: Safety and Instructional Decals Page 2–6 3466-517 A

Decal Part: 147-3025

Models 77506, 77507, and 77603 only

s_decal147-3025

Belt routing

Engine

Decal Part: 147-5152

Models 77506, 77507, and 77603 only

s_decal147-5152

Thrown object hazard—keep

bystanders away.

Thrown object hazard, mower—do

not operate the machine with an open

deck; use a bagger or a deflector.

Cutting/dismemberment hazard of

hands or feet, mower blade—stay away

from moving parts.

Entanglement hazard of hands,

belt—stay away from moving parts;

keep all guards and shields in place.

3466-517A Page 2–7 Safety: Safety and Instructional Decals

Decal Part: 147-7571

Models with an hour meter only

s_decal147-7571

Fast

Slow

Decal Part: 147-7574

MyRIDE models only

s_decal147-7574

Decal Part: 147-8753

Models without an hour meter only

decal147-8753

Fast

Slow

Safety: Safety and Instructional Decals Page 2–8 3466-517 A

Decal Part: 161-6207

decal161-6207

Bypass lever position for pushing

the machine

Bypass lever position for operating

the machine

3466-517A Page 2–9 Safety: Safety and Instructional Decals

Chapter 3

Product Overview

G454341

Engine

MyRide® suspension

adjustment lever (machines

with MyRide suspension only)

Control panel

Deflector

Height-of-cut pin

Deck-lift pedal

Anti-scalp roller

Front caster wheel

Motion-control lever

Fuel-tank cap

Product Overview Page 3–1 3466-517 A

Control Panel

G453238

Throttle control

Choke control

Key switch

Blade-control switch (power

takeoff)

Hour meter (certain models only)

Key Switch

Use the key switch to start or shut off the machine.

G375755s

Shut off the engine

Run the engine

Start engine

Throttle Control

G450843

The throttle controls the engine speed, and it has a

continuous-variable setting from the SLOW to FAST

position.

3466-517A Page 3–2 Product Overview: Control Panel

Blade-Control (PTO) Switch

G428617

The blade-control switch, represented by a power-

takeoff (PTO) symbol, engages and disengages

power to the mower blades.

Choke Control

Use the choke control to aid in starting a cold engine.

G419508

Engaged Disengaged

Hour Meter

For Machines with an Hour Meter

The hour meter records the number of hours the engine is running. Use these times for

scheduling regular maintenance.

Motion-Control Levers

Use the motion-control levers to drive the machine forward, reverse, and turn either

direction.

Park Position

G438246

Move the motion-control levers outward from the

center to the PARK position to engage the parking

brake when stopping or exiting the machine.

Product Overview: Control Panel Page 3–3 3466-517 A

La page charge ...

Toro TimeCutter Max 54in Zero Turn Riding Mower Manuel utilisateur

Ce manuel convient également à

Toro TimeCutter Max 54in Zero Turn Riding Mower Manuel utilisateur

dans d''autres langues

Documents connexes