ab Naida CI Q90 Manuel utilisateur

Naída CI Sound Processor user guide

English, Français, Español, Deutsch, Nederlands, Português

029-M497-85 Rev A

user guide

for the Naída CI Q90 Sound Processor

2 Naída CI Q90 Sound Processor User Guide

Labeling

Labeling symbols and their meanings:

*Only applicable if ‘refurbished’ is noted on the shipping label

Warning and Cautions

WARNINGS

• CHOKING HAZARD–contains small parts that pose a hazard of inhalation.

• Do not use or store the AB myPilot in shirt pockets if the recipient has a pacemaker, as

there is potential for interference. Contact a health care professional for more information.

European Community Mark of Conformity. Authorized to afﬁx the CE Mark in 2015

Model number

Date of manufacture

Serial number

Manufacturer

Type of Protection: B

Store at temperatures between -20˚C (-4˚F) and +55˚C (131˚F)

Fragile

Do not get wet

See Instructions for Use

Suitable for atmospheric range between 70 kPa and 106 kPa, which is equivalent to

3000 m above sea level to 380 m below sea level

Suitable for exposure to relative humidity between 0-95%

Dispose of in accordance with applicable national and local regulations

The Naída CI Q90 carries a rating of IP57. This rating indicates that the Naída CI Q90 is

protected

against the following conditions: protection against dust, failure due to one time immersion

for 30 minutes to a depth up to 1m and after drying overnight in a dry and store unit

IP57

Refurbished*

Naída CI Q90 Sound Processor User Guide 3

• Do not use a ComPilot if recipient has a pacemaker, as there is potential for

interference. Contact a health care professional for more information.

• Ensure appropriate supervision when child is wearing the Naída CI Q90 sound

processor and accessories.

• Keep batteries and accessories out of children’s reach as they may pose a choking hazard.

• If any parts are swallowed consult a physician or hospital immediately.

• Do not leave children unattended with or allow them to play with batteries.

• Do not place batteries in your mouth.

• Do not chew or swallow batteries. If this occurs, seek immediate medical attention.

• Do not allow children to play with or operate the drying system unattended.

• Using your sound processor and accessories in a manner other than their

intended use (e.g. placing them in your mouth or chewing them) may cause

bodily harm.

• Do not recharge disposable batteries.

• Do not allow leaking battery ﬂuid to come into contact with skin, mouth, or eyes.

• Do not expose batteries to heat (e.g., do not store in direct sunlight or in a hot car).

• Do not dispose of batteries in ﬁre.

• Do not allow children to charge batteries unattended.

• Do not use any power supply with the sound processor, AB myPilot remote

control or ComPilot unless it is supplied by Advanced Bionics or Phonak. If

needed, contact Advanced Bionics for a power supply replacement.

• Do not use the AB myPilot or the ComPilot when they are plugged in to power

sources such as wall outlets or USB compatible power sources such as laptops.

• The ComPilot comes with a neck loop antenna. Do not touch the neck loop

connectors at the same time.

• Power supplies and battery chargers should be operated in an open area to ensure

adequate airﬂow. While, to date, no injuries have been reported, components may

become hot during normal use or in the event of a fault. If the device’s temperature

results in discomfort or pain when touched, disconnect the power source and

contact your local Advanced Bionics representative.

4 Naída CI Q90 Sound Processor User Guide

CAUTIONS

• Remove external equipment to stop stimulation if sounds cause discomfort.

• It is important for the headpiece to have the correct magnet strength to

avoid discomfort or retention issues. If an insufﬁcient number of magnets

are used, the headpiece may fall off more than is acceptable. If too many

magnets are used, the recipient may experience irritation or discomfort. Consult

a clinician if there are any concerns regarding magnet strength. If deemed

appropriate, an audiologist may insert additional magnets or remove magnets

from the headpiece. Do not place additional magnets in the headpiece unless

under the direction of a cochlear implant professional. If the recipient experiences

any redness, irritation, or discomfort, discontinue use of the headpiece immediately

and contact a cochlear implant center. See the headpiece Instructions for Use for

additional information regarding adjustment of headpiece magnet strength.

• If the sound processor or accessories become unusually hot or warm, discontinue

use immediately and contact Advanced Bionics or a clinician.

• Store additional headpieces away from items with magnetic strips (e.g. credit

cards, hotel room key cards), as this may de-magnetize cards.

• Portable and mobile RF communications equipment, including radios and

cellular phones, may affect sound quality of the Naída CI Q90 sound processor and

accessories; however, there is no safety hazard associated with such equipment.

• The Naída CI Q90 sound processor and accessories should be used in accordance

with the electromagnetic compatibility (EMC) information provided in the Guidance and

Manufacturer’s Declaration section of the Instructions for Use.

• Only use the charger provided for charging AB PowerCels. Do not use it to

charge other batteries. Do not try to charge Naída CI Q90 PowerCels using a charger

other than the one provided by Advanced Bionics.

• Remove batteries from your sound processor when they are drained to prevent

damage from possible leaking.

• Do not expose any part of the Naída CI Q90 sound processor or accessories to

extreme heat, such as an oven, microwave, or hair dryer.

• Only charge batteries using charger(s) recommended by the manufacturer.

• Do not use your AB myPilot or ComPilot accessories when instructed not to use

wireless electronic devices, such as on airplanes.

• The AB myPilot should not come within 1/2” (1 cm) of the Naída CI Q90 processor

Naída CI Q90 Sound Processor User Guide 5

while stimulating the implant. Doing so could cause the implant and sound

processor to lose lock. If this happens, power down the processor and power back

on (by disengaging the battery and reattaching).

• The digitally-coded, inductive transmission technology used in this device is

extremely reliable and experiences virtually no interference from other devices.

It should be noted, however, that when operating the device near a computer

terminal or other strong electromagnetic ﬁelds, it may be necessary to be at least

24” (60 cm) away to ensure proper operation. If the Naída CI Q90 does not respond

to the implant device because of an unusual ﬁeld disturbance, move away from

the disturbing ﬁeld.

• If the AB myPilot stops being able to transmit commands to the sound processor,

it may be necessary to re-pair the AB myPilot with your sound processor. Consult the

Pairing to the AB myPilot section of this user manual.

• If volume commands from your AB myPilot to your sound processor seem erratic,

re-pair the AB myPilot and the Naída CI Q90.

• NOTE: When streaming audio with the ComPilot, if your headpiece becomes

unlocked, turn off the ComPilot prior to re-locking your headpiece. Not doing so

may prevent the sound processor from communicating with your implant.

• Patients are advised that the use of WindBlock, EchoBlock and/or SoundRelax

may affect the quality of sound.

Electrostatic Discharge (ESD)

High levels of static electricity may damage electronic components of your sound processor or

implant. Care should be taken to avoid exposure of the system to static electricity. ESD is present

when you feel a spark jump from your body or your hair

stands on-end.

The following are examples of situations where high levels of electrostatic charge may be created:

• Walking, crawling, or sliding on carpets.

• Sliding on plastic slides.

• Exiting an automobile.

• Pulling sweaters on and off.

• Touching TV or computer screens.

• Removing bedding materials.

6 Naída CI Q90 Sound Processor User Guide

To reduce the likelihood of electrostatic discharge damage:

• Touch a person or object with your ﬁngers prior to touching your or your child’s headpiece, cable,

or sound processor.

• Touch metal surfaces with your hand prior to allowing equipment to contact the metal surface.

This is particularly important on the playground where high levels of static electricity can be

generated. It is important to discharge any static electricity by touching a metal surface with your hand

prior to allowing the sound processor, cable, or headpiece to come into contact with the metal

surface.

• Take care to avoid contact between your cochlear implant equipment and metal surfaces

when exiting a vehicle.

• Remove cochlear implant equipment prior to removing clothing that may contain electric

charge (e.g. sweaters).

• Do not touch TV or computer screens. If screens are touched, be sure to touch an object

other than your implant system to discharge any charge build-up prior to touching any part

of your implant system.

• Use fabric softener on clothing and bedding.

Airport Security Metal Detectors

Metal detectors and security scanners, including full body scanners, will not damage your

implant system; however, metal detectors may be activated as you pass through. To avoid

hearing any unwanted sound when walking through metal detectors or security scanners, you

should reduce the volume on the sound processor or remove your headpiece.

Ultrasonic Sensors

Ultrasonic sensors, sometimes used in lighting sensors and security systems, will not damage

your implant system; however, they may be picked up by the headpiece microphone and lead

to distorted sound quality when you operate your sound processor in the immediate vicinity

of such a sensor. Additionally, if the ultrasonic sound is of a very high intensity, the processor

system microphone may become damaged. To avoid hearing any unwanted sound, you should

reduce the volume on your sound processor or remove your headpiece when passing near an

ultrasonic sensor (e.g. in entrances to libraries).

X-ray Machines

X-ray machines will not damage your sound processor or implant, but may damage your Naída

CI Q90 and head piece microphones. Avoid placing any system microphones in any checked

or carry-on baggage that is screened with X-ray. During airport security screenings, the sound

processor and microphone should be worn through the metal detector or examined by hand.

Table of Contents

Introduction ...............................................................................................................................10

Purpose of this Guide .....................................................................................................................10

About the Naída CI Q90 Sound Processor .........................................................................10

The Naída CI Q90 Sound Processor ................................................................................11

The Naída CI Q90 Sound Processor and Accessories Overview ..........................12

The Naída CI Q90 ...........................................................................................................................12

The Universal Headpiece .............................................................................................................13

AB myPilot ............................................................................................................................................ 13

ComPilot ................................................................................................................................................14

Naída CI Listening Check ............................................................................................................. 14

AquaCase™ Container ...................................................................................................................15

Phonak DECT Phone ......................................................................................................................15

Naída CI Q90 Sound Processor Features ......................................................................16

auto UltraZoom .................................................................................................................................16

StereoZoom ......................................................................................................................................... 16

UltraZoom ............................................................................................................................................ 16

WindBlock .............................................................................................................................................16

SoundRelax ..........................................................................................................................................16

EchoBlock .............................................................................................................................................17

DuoPhone ............................................................................................................................................17

ZoomControl .......................................................................................................................................17

QuickSync .............................................................................................................................................17

Assembling the Naída CI Q90 ........................................................................................... 17

Connecting the Universal Headpiece (UHP) Color Caps ............................................ 18

Connecting the Headpiece to the Naída CI Q90 ............................................................18

Removing the Headpiece from the Naída CI Q90 .........................................................19

Connecting the T-Mic™ 2/Earhook ..........................................................................................19

Removing the T-Mic 2/Earhook.................................................................................................20

Attaching the T-Mic 2 Cover .......................................................................................................21

Removing the T-Mic 2 Cover ......................................................................................................21

Wearing the Naída CI Q90 .................................................................................................22

Using the Clip .....................................................................................................................................22

Inserting the Naída CI Q90 in the Clip ................................................................................. 23

Removing the Naída CI Q90 from the Clip ........................................................................24

Using the Naída CI Q90 Sound Processor ....................................................................24

Powering the Naída CI Q90 .......................................................................................................24

Removing the Battery .....................................................................................................................25

Replacing the Battery ..................................................................................................................... 26

Understanding Naída CI Q90 LEDs .......................................................................................27

Understanding Internal Alarms .................................................................................................28

Using Naída CI Headpieces ................................................................................................28

The Universal Headpiece .............................................................................................................28

Replacing the RF Cables ...............................................................................................................28

Adjusting Headpiece Magnet Strength ................................................................................29

Removing Headpiece Color Caps ............................................................................................ 30

Adjusting Controls on the Naída CI Q90 .......................................................................30

Changing Programs ........................................................................................................................ 30

Changing Volume.............................................................................................................................31

Changing Sensitivity ........................................................................................................................32

Connectivity ...............................................................................................................................32

Using FM/Roger ................................................................................................................................32

Pairing to the AB myPilot ..............................................................................................................35

The Naída CI Listening Check and Listening Check Earbuds ................................38

Listening to the Microphone(s) and Auxiliary Inputs .....................................................38

Using the Telephone .......................................................................................................................41

Telephone Tips ................................................................................................................................... 42

Telecoil ....................................................................................................................................................42

Battery Information ................................................................................................................ 43

Assembling the PowerCel™ Charger ......................................................................................44

Inserting the PowerCels into the Charger ............................................................................45

Removing the PowerCels from the Charger........................................................................45

The Zn-Air Battery Pak ...................................................................................................................46

Inserting Zn-Air Batteries ..............................................................................................................46

Inserting Zn-Air Batteries (Tamperproof Cartridge) ........................................................47

Charger LED (Light Emitting Diode) Indicator ..................................................................48

Warnings ............................................................................................................................................... 49

Cautions ................................................................................................................................................49

Using Naída CI Accessories ................................................................................................49

Headpieces .......................................................................................................................................... 50

ComPilot ................................................................................................................................................50

Naída CI Listening Check and Listening Check Earbuds.............................................50

Audio Accessories ............................................................................................................................ 51

Color Customization ........................................................................................................................51

Naída CI Carrying Case ................................................................................................................52

Drying System .....................................................................................................................................52

IP Rating Information ............................................................................................................53

Care of the Naída CI Q90 Sound Processor and Accessories ................................53

Changing Microphone Covers ...................................................................................................53

Recommended Naída CI Q90 Operating and Storage Temperatures ................ 55

Approved Power Sources ..............................................................................................................55

Troubleshooting the Naída CI Q90 .................................................................................. 55

Troubleshooting Naída CI Q90 LEDs ....................................................................................57

Troubleshooting Naída CI Q90 Internal Alarms .............................................................. 59

Guidance and Manufacturer’s Declaration .................................................................. 60

Electromagnetic Emissions .......................................................................................................... 60

Electromagnetic Immunity ..........................................................................................................60

Separation Distances between RF Communications

Equipment and Naída CI Q90...................................................................................................61

Compatibility Tables ........................................................................................................................ 62

Cleaning & Maintenance .............................................................................................................63

Performance Data ..................................................................................................................63

HiRes™ and HiRes Fidelity120™ Sound Processing........................................................63

Contact Us .................................................................................................................................65

10 Naída CI Q90 Sound Processor User Guide

Sound Processor

Power Source

(PowerCel)

Universal Headpiece (UHP)

Introduction

Purpose of this Guide

This user guide is designed to help recipients, parents, and caregivers understand the use and

care of the Naída CI Q90 sound processor. The Naída CI Q90 sound processor represents the

latest in high-performance sound processing from Advanced Bionics. As the most advanced

sound as well as the smallest processors ever developed by AB, this latest generation in hearing

solutions features state-of-the-art technologies exclusively available from Advanced Bionics and

Phonak for the best possible hearing experience.

The Naída CI Q90 provides access to the latest sound processing innovations by Advanced

Bionics, the market leader in performance. This guide will provide all of the information needed

to use and care for the Naída CI Q90 and its accessories. In addition, this guide will provide

information for troubleshooting basic issues related to the Naída CI Q90, as well as important

safety information. Please read the entire manual prior to using the Naída CI Q90.

About the Naída CI Q90 Sound Processor

The Naída CI Q90 sound processor is one part of a complete cochlear implant system that

enables hearing. The other necessary parts of the system are the Implantable Cochlear

Stimulator (ICS), headpiece, and headpiece cable.

The sound processor consists of two parts: the sound processor and battery power source. There

are seven battery options, including two sizes of Lithium Ion rechargeable PowerCel™ batteries*,

two sizes of Lithium Ion rechargeable PowerCel Mini batteries* and a Zn-Air Battery Pak. The

recipient also has the option of wearing the power source completely off the ear by using either

the AAA/03 PowerPak or the Power Adapter. Please refer to the AAA PowerPak and Power

Adapter Instructions For Use for more details on these products.

* PowerCels refers to Naída CI PowerCel and Naída CI PowerCel Mini unless otherwise noted

Naída CI Q90 Sound Processor User Guide 11

AB myPilot

ComPilot

LEDs

The Naída CI Q90 includes programmable, multi-color light-emitting diode (LED) indicators

and programmable internal alarms for easy status updates and troubleshooting information.

Additional features include remote control access through the AB myPilot remote control and

the ability to stream from the Phonak ComPilot.

The Naída CI Q90 Sound Processor

This section will familiarize you with the Naída CI Q90 Sound Processor and Accessories

Sound Processor

Battery Cartridge

Program Button

Volume Control and Tri-Colored LEDs

(green, orange, red)

Volume Control

Universal Headpiece (UHP)

Microphone

Headpiece Cable

Phonak Dual-Microphone Technology

(front and back microphones)

AB’s Patented T-Mic™ 2 microphone

12 Naída CI Q90 Sound Processor User Guide

The Naída CI Q90 Sound Processor and Accessories Overview

The Naída CI Q90 is the newest and most advanced cochlear implant sound processor

available.

As evidence of Advanced Bionics’ dedication to providing the best hearing possible, the Naída

CI Q90 provides access to AutoSound™ technology, which dynamically adapts to every listening

environment, automatically adjusting volume levels to optimize hearing. The Naída CI Q90 is

also capable of utilizing all approved sound processing options offered by Advanced Bionics.

Depending on the country in which you live, this may include HiRes™-S, HiRes™-P, HiRes Fidelity

120™, ClearVoice™, HiRes™ Optima, CIS, and MPS.

The Naída CI Q90

The Naída CI Q90 is a miniature computer that converts sound picked up by the microphone

into electrical signals that are used by the cochlear implant to enable hearing. It is able to store

up to ﬁve (5) user-selectable programs for optimal hearing across all listening environments.

The Naída CI Q90 has diagnostic indicators, such as LEDs and internal audible alarms. The

Naída CI Q90 LEDs provide important information about Naída CI Q90 status, battery life,

program position, audio input, and Naída CI Q90 error conditions. Internal alarms provide a

discreet way for adult recipients to get important information about battery status, program

number, and volume level. For more information, refer to the Naída CI Q90 LEDs and Internal

Alarms sections of this User Guide.

The Naída CI Q90 can be programmed using Intellilink™ safety feature to prevent use by

a cochlear implant other than the one for which it has been programmed. IntelliLink is an

important safety feature for very young children and bilateral implant recipients.

The Naída CI Q90 can also be programmed bilaterally allowing the recipient access to up to

ten programs on a single processor, up to ﬁve programs for the left ear and up to ﬁve programs

for the right ear. When programmed bilaterally by your clinical professional, the Naída CI Q90

will detect which ear it is worn on and provide access to the appropriate programs for that ear.

Tri-Colored LEDs

(green, orange, red)

Naída CI Q90 Sound Processor User Guide 13

The Universal Headpiece

The Universal Headpiece includes a coil that transmits sound signals and power to the implant,

as well as a magnet well, which houses the necessary number of magnets to ensure the

headpiece stays on throughout the day. The headpiece is covered by a Color Cap, which snaps

securely in place. The headpiece also functions as a sound input source, having a microphone

embedded in it. The microphone picks up sound from the environment and transfers it to the

sound processor via a detachable cable. Once the sound processor has converted the sound

into electric signals, it sends the information to the implant via the cable and headpiece. The

cables come in a variety of colors and lengths to suit all needs. The Naída CI Q90 works with

the Universal Headpiece.

The Universal Headpiece (UHP), works with all Advanced Bionics’ sound processors, and is

intended for use with the Naída CI Q90 outside of water environments.

For more information, refer to the Replacing Headpiece Cables section of the User Guide or the

UHP and/or Cable Instructions for Use.

AB myPilot

The AB myPilot is an advanced remote control that leverages Phonak technology to enable

wireless communication for unilateral and bilateral Naída CI recipients. The AB myPilot provides

convenient controls to manipulate program, volume, sensitivity, source-speciﬁc listening checks,

and ZoomControl for the Naída CI Q90. The AB myPilot also has the ability to provide status

and battery information for Naída CI processors. For bilateral Naída CI users, AB myPilot offers

one-touch binaural controls, allowing changes to be made to both processors at once.

Color Cap

Microphone Cable Connection Port

14 Naída CI Q90 Sound Processor User Guide

ComPilot

The ComPilot allows unparalleled connectivity for Naída CI recipients, connecting them

wirelessly to Bluetooth® enabled phones and devices or MP3 players for speech or stereo music.

It is also compatible with Phonak’s portfolio of FM receivers via a euro socket. Additionally,

when unpaired, the ComPilot is able to stream to compatible Phonak instruments. This allows

bimodal wearers -- people who wear a Naída CI on one ear and a Phonak compatible hearing

instrument on the other ear -- access to bilateral wireless streaming.

When the ComPilot is paired to the Naída CI, it provides remote control functions to adjust the

Naída CI for increased listening comfort in addition to wireless streaming. When paired, you are

able to make program and volume changes via the ComPilot only to the Naída CI. If you are

bilaterally implanted, changes can be made to both Naída CI processors simultaneously. The

ComPilot also connects both Naída CI processors wirelessly to other communication and audio

devices, allowing you to hear the signal in both ears.

Naída CI Listening Check

The Naída CI Listening Check’s unique design makes conducting a diagnostic check of the

microphone and audio input sources easy and accessible. The Module itself does not have

a power source, as it relies solely on power from the Naída CI power sources (PowerCels,

Zn-Air Battery Pak, AAA/03 PowerPak or Off-the-Ear Power Options). The Naída CI Listening

Check allows an unaided listener to listen to the exact microphone conﬁgurations the recipient

is using. Alternatively, if the recipient owns an AB myPilot, the unaided listener can do a listening

check of all audio sources independently by selecting them individually on the AB myPilot menu.

Naída CI Q90 Sound Processor User Guide 15

AquaCase™ Container

The AquaCase delivers a durable, wearable, and swimmable solution for uncompromised

hearing in and out of water. The AquaCase carries an IP 68 rating for the ultimate protection

against water, sweat, dust, and sand. From farms and construction sites to pools and

playgrounds, you can rest assured your processor is protected in any environment.

Phonak DECT Phone

The Phonak DECT phone is a cordless phone that streams wirelessly to one or both implants

simultaneously. This phone also has the ability to stream to a compatible Phonak hearing

instrument. Apart from the streaming function, the phone has a regular acoustic output and

can therefore be used by non-implant users as well. Up to six handsets can be connected to one

base providing functionality for both home or small-ofﬁce use.

16 Naída CI Q90 Sound Processor User Guide

Naída CI Q90 Sound Processor Features

The Naída CI Q90 provides advanced Phonak features, including UltraZoom, auto UltraZoom,

Front/Back ZoomControl, WindBlock, EchoBlock, and SoundRelax. Bilateral Naída CI Q90 users

may also access Phonak Binaural VoiceStream Technology™ features , including DuoPhone,

Left/Right ZoomControl, StereoZoom, and QuickSync.

These features are programmed by your implant professional in the SoundWave™ professional

suite software.

The Naída CI Q90 includes:

• Smallest form factor of the Naída CI series of sound processors.

auto UltraZoom

auto UltraZoom is designed to be automatically activated, and like UltraZoom

it works adaptively to allow the listener to focus on voices coming from the front.

Even as noise from the side and back moves or changes, it is reduced to allow for

easier listening.

StereoZoom (bilateral only feature)

StereoZoom is designed to enable both Naída sound processors to work together

to focus on the person directly in front of you allowing you to hear them in very

noisy situations.

UltraZoom

UltraZoom works adaptively, and is designed to allow you to focus on voices

coming from the front. Even as noise from the side and back moves or changes, it

is reduced to allow for easier listening.

WindBlock

WindBlock is designed to reduce interference caused by windy conditions and

improve comfort for listeners.

SoundRelax

SoundRelax is designed to soften sudden loud sounds, such as slamming doors or

clanking dishes.

Naída CI Q90 Sound Processor User Guide 17

EchoBlock

EchoBlock is designed to remove the disturbing reﬂections of reverberant sound

in places like large halls and places of worship.

DuoPhone

DuoPhone allows bilateral users the ability to hear phone conversations in both

ears simultaneously while also reducing surrounding noise. By placing the phone

to one ear the conversation is automatically streamed to the other ear as well,

giving the user the best possible listening experience.

ZoomControl

When you cannot face the speaker, for example, in a car, ZoomControl can

be selected to zoom to the front or the back (for both unilateral and bilateral

recipients) or to either side (for bilateral recipients) for effortless understanding.

QuickSync

QuickSync allows for easy, instant, simultaneous adjustments to volume and

program settings on two Naída CI Q90 processors so bilateral users can control

both processors with one touch.

CAUTIONS:

• UltraZoom, StereoZoom, ZoomContol, and auto

Ultrazoom will dampen sounds that are not in front of the recipient.

• Do not use UltraZoom, StereoZoom, ZoomControl, or auto

Ultrazoom in an off-the-ear wearing conﬁguration.

NOTE: StereoZoom, auto UltraZoom, SoundRelax, WindBlock, and EchoBlock are

not approved for pediatric use in the United States.

Assembling the Naída CI Q90

The Naída CI Q90 Sound Processor and accessories consists of a Naída CI Q90 sound

processor, T-Mic™ 2 microphone or earhook option, headpiece, cable, and internal implant.

The Naída CI Q90 has various sound inputs that a hearing care professional can program for

use. The Naída CI Q90 allows access to a front and rear microphone, T-Mic 2, and headpiece

microphone. It also allows for the ability to use T-coil input, wireless FM, and Roger. The Naída

CI Q90 has the ability to wirelessly stream Bluetooth® and directly connect battery-operated

devices via the ComPilot.

The processor provides you with access to the latest in sound processing technology. In addition, the

processor offers you a wide range of wearing options that can be customized to ﬁt lifestyle needs.

18 Naída CI Q90 Sound Processor User Guide

Connecting the Universal Headpiece (UHP) Color Caps

WARNING: Small Parts Hazard: The processor, UHP Color Caps, magnets, and

spacers may cause choking if swallowed.

Attaching the UHP Color Cap

Removing the UHP Color Cap

Connecting the Headpiece to the Naída CI Q90

Align the Color Cap with the headpiece. Gently press the cap and headpiece together.

The Color Cap will snap into place.

1 2

Insert the UHP Removal Tool into the slot

above the headpiece cable connector. Gently push the tool forward to release the

Color Cap as shown above.

1 2

Align the pin on the right-angled end of

the cable with the cable connection port

located below the program button on the

body of the processor.

Press in until you feel it snap into place.

1 2

Naída CI Q90 Sound Processor User Guide 19

Removing the Headpiece from the Naída CI Q90

Connecting the T-Mic 2/Earhook

Line up the pin with the hole in the T-Mic

2/Earhook and gently push it through

the hole. The pin will move from one side

of the processor, through the T-Mic 2/

Earhook, to the other, holding the T-Mic

2/Earhook in place. The pin should not

come out the other side.

If a small portion of the pin extends

beyond the processor, use the side of the

tool to push the pin inward so it lies ﬂush

with the processor.

3 4

Hold the cable’s connector (the right-angled

plastic plug, not the wire). Gently pull the cable’s connector away

from the Naída CI.

1 2

Beginning with either the earhook or

T-Mic 2 disconnected, align the T-Mic 2

or earhook ﬂush with the processor. Hold

the T-Mic 2 or earhook ﬁrmly at the top

and push towards the processor until it

meets ﬂush with the processor.

Using the provided T-Mic 2/Earhook tool,

place one of the pins in the small hole on

the side of the tool. This will help to steady

the pin as you line it up with the pin hole

on the T-Mic 2/Earhook.

1 2

La page est en cours de chargement...

ab Naida CI Q90 Manuel utilisateur

ab Naida CI Q90 Manuel utilisateur

dans d''autres langues

Autres documents