LED Descriptions
Buttons and ports
PWR
LED indicator Status Description
Signal
Solid on The repeater is connected to a power source properly.
Off The repeater is not powered on.
WPS
Solid on A WPS connection has been established.
Blinking A WPS connection is being established.
Off The WPS function is disabled.
The repeater does not connect to your WiFi router.
Solid blue
Solid red
Off
The repeater has connected to your existing WiFi router, and its position is proper.
The repeater is too far away from the router.
Relocate the repeater closer to the router.
WPS
Button/Port Description
When the PWR LED of the repeater is solid on, hold down this button using a needle, and
release it when all the LED indicators blink once then turn off. When the PWR LED indicator
turns solid on again, it is reset successfully.
LAN port.
- In repeater mode, it is used to connect to a computer or an IPTV STB.
- In AP mode, it is used to connect to your wired router to provide wireless network for wireless
devices.
Press the button of the router, and enable the WPS function of another device within 2
minutes to establish a WPS connection.
RESET
Power on the repeater
Power on the repeater
Plug the repeater into a power outlet near the router in the
same room.
Wait until the PWR LED indicator turns solid on.
Extend your WiFi network
Press the WPS button on the router. Within 2 minutes, press
the WPS button on the repeater.
Enter the password for the selected WiFi network. Modify your
repeater’s SSID (optional), and click Extend.
5.
Extend your WiFi network
Connect your WiFi device to the repeater’s SSID Tenda_EXT.
Ensure that the Mobile Data (if any) function of your WiFi device
is disabled.
For better performance, follow the on-screen tips or the steps
below to relocate your repeater.
Plug the repeater into an outlet halfway between the router
and the WiFi dead zone.
The location you choose must be within the range of your
existing WiFi network.
1.
Relocate the repeater
For better performance, plug the repeater into an outlet halfway
between the router and the WiFi dead zone.
The location you choose must be within the range of your existing
WiFi network.
1.
Wait until the Signal LED turns solid blue. If not, relocate the
repeater closer to the router.
2.
Wait until the Signal LED on the repeater turns solid blue or red.
If not, try Method 1.
2.
Create a login password for security (recommend) and click Next.3.
re.tenda.cn
After connecting to the repeater’s SSID, you will be directed to
the quick setup page. If not, start a web browser, and access
re.tenda.cn or 192.168.0.254 in the address bar.
2.
1.
Method 1:
Extending your WiFi network using web UI
Method 2:
Extending your WiFi network using WPS
Relocate the repeater
Connect your WiFi devices to the repeater using the SSIDs set by
yourself, or your router’s SSID with the suffix _EXT or _5GEXT if
they are not changed, and using the WiFi password which is the
same as your router.
Connect to the Internet
Connect your WiFi devices to the repeater. The repeater’s SSIDs are
your WiFi router’s SSID with a suffix _EXT or _5GEXT. The WiFi
password of the repeater is the same as your WiFi router.
Connect to the Internet
FCC Statement
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to
Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful
interference in a residential installation. This equipment generates, uses and can radiate radio frequency
energy and, if not installed and used in accordance with the instructions, may cause harmful interference to
radio communications. However, there is no guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful interference to radio or television reception, which can be
determined by turning the equipment off and on, the user is encouraged to try to correct the interference by
one or more of the following measures:
— Reorient or relocate the receiving antenna.
— Increase the separation between the equipment and receiver.
— Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
— Consult the dealer or an experienced radio/TV technician for help.
This device is restricted to be used in the indoor.
Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and
(2) this device must accept any interference received, including interference that may cause undesired
operation.
IC RSS warning
Industry Canada(RSS-Gen Issue 4)
The device for operation in the band 5150-5250 MHz is only for indoor use to reduce the potential for
harmful interference to co-channel mobile satellite systems
les dispositifs fonctionnant dans la bande 5150-5250 MHz sont réservés uniquement pour une utilisation à
l’intérieur afin de réduire les risques de brouillage préjudiciable aux systèmes de satellites mobiles utilisant
les mêmes canaux
This device complies with Industry Canada’s licence-exempt RSSs. Operation is subject to the following two
conditions:
(1) This device may not cause interference; and
(2) This device must accept any interference, including interference that may cause undesired operation of
the device.
Le présent appareil est conforme aux CNR d’Industrie Canada applicables aux appareils radio
exempts de licence. L’exploitation est autorisée aux deux conditions suivantes :
(1) l’appareil ne doit pas produire de brouillage;
(2) l’utilisateur de l’appareil doit accepter tout brouillage radioélectrique subi, même si le brouillage est
susceptible d’en compromettre le fonctionnement.
IC Radiation Exposure Statement:
This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter.
This equipment should be installed and operated with a minimum distance of 20 centimeters between the
radiator and your body.
Cet émetteur ne doit pas être Co-placé ou ne fonctionnant en même temps qu'aucune autre antenne ou
émetteur. Cet équipement devrait être installé et actionné avec une distance minimum de 20 centimètres
entre le radiateur et votre corps.
The device meets the exemption from the routine evaluation limits in section 2.5 of RSS 102 and compliance
with RSS-102 RF exposure, users can obtain Canadian information on RF exposure and compliance.
Le dispositif rencontre l’exemption des limites courantes d’évaluation dans la section 2.5 de RSS 102 et la
conformité à l’exposition de RSS-102 rf, utilisateurs peut obtenir l’information canadienne sur l’exposition et
la conformité de rf.
Caution:
Any changes or modifications not expressly approved by the party responsible for compliance could void the
user's authority to operate this equipment.
This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter.
NOTE: (1) The manufacturer is not responsible for any radio or TV interference caused by unauthorized
modifications to this equipment. (2) To avoid unnecessary radiation interference, it is recommended to use a
shielded RJ45 cable.
Radiation Exposure Statement
This device complies with FCC radiation exposure limits set forth for an uncontrolled environment and it also
complies with Part 15 of the FCC RF Rules.
This equipment should be installed and operated with minimum distance 20cm between the device and your body.
Select the WiFi network (SSID) you want to extend.4.
Select the WiFi network you want
to extend...
My_home_wifi
Rescan Switch Mode
1.
2. Wait until the Signal LED turns blue. If not, relocate the
repeater closer to the router.
Plug the repeater into a power outlet near the router in the same
room.
Wait until the PWR LED turns solid on.
FAQ
I cannot log in to the web UI of the repeater. What
should I do?
Try the following solutions:
If a WiFi device is used, ensure that your WiFi device has
connected to the repeater’s WiFi network Tenda_EXT,
and the Mobile Data (if any) function is disabled.
If a computer is used, ensure that your computer has
connected to the repeater’s WiFi network Tenda_EXT,
and your computer has set to Obtain an IP address
automatically and Obtain DNS server address
automatically.
Reset the repeater, and try again.
Q1:
A1:
How to reset the repeater?
When the PWR LED of the repeater is solid on,
press the RESET button on the repeater using a
needle, and release it when all the LED indicators
blink once then turn off. After the PWR LED turns
solid on, the repeater is restored to the factory
settings successfully.
Q2:
A2:
The repeater cannot find the WiFi network of
my router. What should I do?
Try the following solutions:
Q3:
A3:
Ensure that the WiFi network of your router is
enabled and can be detected by your WiFi
device.
Change the channel of your router, and try
again.
Change the encryption type of the router to
WPA-PSK or WPA2-PSK, and try again.
CE Mark Warning
This is a Class B product. In a domestic environment, this product may cause radio interference, in which
case the user may be required to take adequate measures.
Operations in the 5.15-5.25GHz band are restricted to indoor use only.
This equipment should be installed and operated with minimum distance 20cm between the device and
your body.
The mains plug is used as disconnect device, the disconnect device shall remain readily operable.
For passthrough devices, plug the power strips into the integrated electrical sockets of the devices, but
devices of the same or another type not be stacked in normal use.
NOTE: (1) The manufacturer is not responsible for any radio or TV interference caused by unauthorized
modifications to this equipment. (2) To avoid unnecessary radiation interference, it is recommended to use a
shielded RJ45 cable.
Declaration of Conformity
Hereby, SHENZHEN TENDA TECHNOLOGY CO. LTD. declares that the radio equipment type A18 is in
compliance with Directive 2014/53/EU.
The full text of the EU declaration of conformity is available at the following internet address:
http://www.tendacn.com/en/service/download-cata-101.html.
Declaration of Conformity
Hereby, SHENZHEN TENDA TECHNOLOGY CO. LTD. declares that the radio equipment type A15 is in
compliance with Directive 2014/53/EU.
The full text of the EU declaration of conformity is available at the following internet address:
http://www.tendacn.com/en/service/download-cata-101.html.
RECYCLING
This product bears the selective sorting symbol for Waste electrical and electronic equipment (WEEE). This
means that this product must be handled pursuant to European directive 2012/19/EU in order to be recycled
or dismantled to minimize its impact on the environment.
User has the choice to give his product to a competent recycling organization or to the retailer when he
buys a new electrical or electronic equipment.
Technical Support
Shenzhen Tenda Technology Co., Ltd.
6-8 Floor, Tower E3, NO.1001, Zhongshanyuan Road, Nanshan District, Shenzhen, China. 518052
USA hotline: 1-800-570-5892
Toll Free: Daily-9am to 6pm PST
Canada hotline: 1-888-998-8966
Toll Free: Mon - Fri 9 am - 6 pm PST
Copyright
© 2020 Shenzhen Tenda Technology Co., Ltd. All rights reserved.
is a registered trademark legally held by Shenzhen Tenda Technology Co., Ltd. Other brand and
product names mentioned herein are trademarks or registered trademarks of their respective holders.
Specifications are subject to change without notice.
HongKong Hotline: 00852-81931998
Global Hotline: +86 755-2765 7180 (China Time Zone)
Website: http://www.tendacn.com
E-mail: [email protected]
You can use Method 2 if your router has a WPS button, which may be indicated by , , or . Otherwise, use Method 1.
WPS
re.tenda.cn
Create your login password
For security of your network, you are
recommended to set a login password. The
password is used for your later login.
Password (5 – 32 characters)
Confirm
Next Not Now
Wait until the Extended successfully page appears.
WiFi router
Antennas upward and vertical to the ground
Blue: Good connection
Red: Poor connection
A18
Signal
WiFi router
Antennas upward and vertical to the ground
Blue: Good connection
Red: Poor connection
A18
Signal
Press
Operating Frequency:
2.4G: EU/2400-2483.5MHz (CH1-CH13)
5G: EU/5150-5250MHz (CH36-CH48)
EIRP Power (Max.):
2.4GHz: 19.5dBm
5GHz: 20.5dBm
Software Version:
V02.03.01.116
Your existing WiFi network
Enter the password of “My_home_wifi”
My_home_wifi_5GEXT
Password of the extended network is
same as your existing WiFi network.
The extended WiFi network
SSID
Back Extend
PWR
PWR
Operating Temperature: 0 °C - 40 °C Operating Humidity: (10% - 90%) RH, non-condensing
For product or function details, please go to www.tendacn.com to download the
user guide.
Dual Band WiFi Repeater
A18/A15
Quick Installation Guide
Package contents
WiFi repeater × 1 Ethernet cable × 1 Quick installation guide × 1
(A18 is used for illustration in this guide)
-
1
dans d''autres langues
- English: Tenda A18 Installation guide
Documents connexes
Autres documents
-
Feit Electric FM13 Smart 13-Inch Flush Mount Ceiling Fixture Guide d'installation
-
Asus RP-AC68U Guide de démarrage rapide
-
GL iNet GL-AXT1800 Mode d'emploi
-
BrosTrend AC1200 Guide d'installation
-
Asus RP-AC53 Guide de démarrage rapide
-
Comtrend Corporation WAP-5903 Manuel utilisateur
-
Renkforce AC1200 Le manuel du propriétaire
-
Netgear MBR1516 Manuel utilisateur
-
Renkforce RF-WR-N300MINI Le manuel du propriétaire
-
Cradlepoint MBR1400 Series Manuel utilisateur
