Sony KP-XA43M61 Le manuel du propriétaire

4-083-403-12 (1)

Projection TV

Operating Instructions

Mode d’emploi

xxxxxxxxxx

C

PR

F

EN

A

KP-XA43

M61, M91, M31

Projection TV

KP-XA43

2

3

TV SYS: B/G

AUTO PROGRAM

VHF LOW

PR: 01

1

L(MONO)

R

3

ENTER MENU

4

5

-EN

Getting Started

WARNING

To prevent fire or shock hazard, do not expose the

projection TV to rain or moisture.

Dangerously high voltages are present inside the

projection TV. Do not open the cabinet. Refer

servicing to qualified personnel only.

For general safety:

• Do not expose the projection TV to rain or moisture.

• Do not open the rear cover.

For safe installation:

• Do not block the ventilation openings.

• Do not install the projection TV in hot, humid or

excessively dusty places.

• Do not install the projection TV where it may be

exposed to mechanical vibrations.

• Avoid operating the projection TV at temperatures

below 5°C (41°F).

• If the projection TV is transported directly from a

cold to a warm location, or if the room temperature

has changed suddenly, the picture may be blurred or

show poor color. This is because moisture has

condensed on the mirror or lenses inside. If this

happens, let the moisture evaporate before using the

projection TV.

• To obtain the best picture, do not expose the screen to

direct illumination or direct sunlight. It is

recommended to use spot lighting directed down

from the ceiling or to cover the windows that face the

screen with opaque drapery. It is desirable to install

the projection TV in a room where the floor and walls

are not of reflecting material. If necessary, cover

them with dark carpeting or wall paper.

• Do not install the appliance in a confined space, such

as a bookcase or built-in cabinet.

For safe operations:

• Do not operate the projection TV on anything but

110–120/220-240 V AC, 50/60 Hz.

• Do not operate the projection TV if any liquid or solid

object falls in it—have it checked immediately.

• Do not keep the projection TV plugged in if you are

not going to use it for several days.

• Do not pull the power cord to disconnect the

projection TV. Pull it out by the plug.

Caution

• When using TV games, computers, and similar

products with your projection TV, keep the

brightness and contrast functions at low settings. If a

fixed (non-moving) pattern such as a station logo is

left on the screen for long periods of time at a high

brightness or contrast setting, the image can be

permanently imprinted onto the screen. These types

of imprints are not covered by your warranty.

• Avoid touching the screen surface and do not scratch

it with hard objects.

Table of contents

Getting Started

6 Connections

9 Installing the projection TV

10 Getting to know the remote commander

11 Introducing the menu system

12 Changing the menu language

13 Presetting channels

16 Adjusting the convergence (CONVERGENCE)

Operations

17 Watching the TV

19 Adjusting the picture and sound

21 Listening with dynamic sound (POWER BASSO)

22 Listening to the surround sound (HYPER

SURROUND)

23 Selecting a stereo or bilingual program

24 Viewing Teletext

25 Operating optional components

27 Viewing a video game screen (GAME MODE)

28 Customizing the TV

Additional Information

29 Troubleshooting

30 Cleaning the screen

30 Specifications

EN

6

-EN

Getting Started

1

L

(MONO)

R

2

3

Connections

On a wall

Rear of TV

or

Rear of TV

VCR

to

S video

output

to

antenna

output

to video and

audio outputs

: Signal flow

Getting Started

to (antenna) socket

to … 1, 2, or 3 (video input)

(yellow)

-L (MONO)(white)

-R (red)

to (S video input)

Connecting a VHF antenna or a combination VHF/UHF antenna

— 75-ohm coaxial cable (round)

Attach an optional IEC antenna connector to the 75-ohm coaxial cable.

Plug the connector into the (antenna) socket at the rear of the TV.

Connecting optional equipment

You can connect optional audio/video equipment to your TV such as a VCR, multi disc player, camcorder, video

game or stereo system.

Connecting video equipment using video input jacks

7

-EN

Getting Started

L(MONO)

R

3

1

L

(MONO)

R

2

3

(VARIABLE)

RL

Camcorder

to S video output

to video and

audio outputs

: Signal flow

Rear of TV

VCR

to

antenna

output

to video and

audio inputs

Audio system

to audio

inputs

: Signal flow

or

to (S video input)

to … 3 (video input)

(yellow)

-L (MONO)(white)

-R (red)

to (antenna) socket

to Ú (monitor/TV output)

(yellow)

-L (MONO)(white)

-R (red)

When connecting a monaural VCR

Connect the yellow plug to (video input) and the black plug to -L (MONO) (audio input).

When connecting video game equipment

Connect video game equipment to the … 3 (video input) jacks at the front or the rear of your TV.

When connecting a VCR to the (antenna) terminal

Preset the signal output from the VCR to the program position 0.

When connecting video equipment to the … 3 (video input) jacks at the front and the rear

Do not connect video equipment to the … 3 (video input) jacks at the front and the rear of your TV simultaneously; otherwise the picture

will not be displayed properly on the screen.

If both S Video and video signals are input simultaneously

The S video input signal is selected. To view a video input signal, disconnect the (S video) connection.

Note on the video input

When no signal is input, the screen becomes blue.

Connecting audio/video equipment using Ú (monitor/TV output) jacks

When the audio cable is connected to the (VARIABLE) jacks, you can adjust the volume with Á +/–.

Front of TV

8

-EN

Getting Started

COMPOMENT VIDEO OUT

S VIDEO OUT

LINE OUT

C

B/B-YYCR/R-Y

R-AUDIO-L VIDEO

CR/

R-Y

C

B/

B-Y

Y

L

R

1

L

(MONO)

R

2

3

LINE OUT

R-AUDIO-L VIDEO

Connecting a DVD player

C

Connecting an amplifier with Dolby* Pro Logic decoder

Even though you use an amplifier with Dolby Pro Logic

decoder instead of the projection TV’s audio system, you

can still use the projection TV’s center speaker.

* Manufactured under license from Dolby Laboratories

Licensing Corporation.

DOLBY, the double-D symbol a and “PRO LOGIC” are

trademarks of Dolby Laboratories Licensing Corporation.

Amplifier with Dolby Pro

Logic decoder

Rear

speaker

(L)

Rear

speaker

(R)

Front

speaker

(L)

Front

speaker

(R)

to (center speaker

inputs)

Rear of TV

Connecting a DVD player with component video output connectors

Notes

• Since the high quality pictures on a DVD disc contain a lot of

information, picture noise may appear. In this case, adjust the

sharpness (SHARP) in the VIDEO ADJUST menu. (See page 19.)

• Connect your DVD player directly to your TV. Connecting the

DVD player through other video equipment will cause unwanted

picture noise.

• If your DVD player can output interlace and progressive mode

signals, select the interlace output when connecting to

(component video input) on your TV.

Your TV can receive either 525i/60 Hz or 625i/50 Hz interlace

signals.

Rear of TV

: Signal flow

to audio/

video

outputs

DVD player

to … 1, 2, or 3 (video input)

(yellow)

-L (MONO)(white)

-R (red)

Rear of TV

: Signal flow

-L (white)

-R (red)

to (component video

input) Y/C

B

/B-Y/C

R

/R-Y

to component video

output

to audio output

DVD player

9

-EN

Getting Started

Installing the

projection TV

min 1.5m (5 ft.)

75°

Optimum viewing area (Vertical)

min 1.5m (5 ft.)

27°

For the best picture quality, install the projection TV

within the areas shown below.

Optimum viewing area (Horizontal)

10

-EN

Getting Started

PROGR

MENU

A/B

GAME

1

2

3

4

5

6

7

8

0

-/--

9

ENTER

POWER

BASSO

1

2

3

4

!§

5

6

7

!¶

!•

!ª

!∞

!¢

!£

!™

!¡

!º

9

8

TITLE

VIDEO

Symbol

1

2 ¤

3 A/B

4

5 ÷

6 POWER

BASSO

7 .+/–

8 GAME

9 u

!º …

!¡ ;

!™ 1,2,3,4,5,

6,7,8,9,0

!£ JUMP

!¢ MENU

!∞ V/b/v/B

ENTER

!§ ©

!¶

!• PROGR +/–

!ª

VIDEO u

+/#

(

=/3

p

P

r

TITLE

Names/symbols of buttons on the remote commander are indicated in different colors to represent the available

functions.

Label color Button function

Grey For general TV operations.

Green For Teletext operations.

Getting to know the

remote commander

Name Refer to page

On-screen display button 18

Teletext: Reveal button 25

Mute on/off button 18

Sound select button 23

Teletext: Enlarge button 25

Teletext button 24

Double-digit entering button 17

POWER BASSO button 21

Volume control button 17

GAME button 25

TV standby button 17

Input mode selector 18

Hold button 24

TV power on/TV mode selector 18

Number buttons 17

JUMP button 18

MENU button 11

Cursor control key 11

Enter button 11

Teletext: INDEX button 24

Sleep timer button 18

Teletext: Text clear button 25

Program selectors 17

DVD, VCR, MDP, CD, MD 25

operation buttons

Power button 25

Fastforward/search forward 26

button

Play button 26

Rewind/search backward 26

button

Stop button 26

Pause button 26

Record button 26

TITLE button 26

11

-EN

Getting Started

A / V CONTROL

DYNAMI C

SOFT

STANDARD

PERSONAL

V I DEO ADJUST

AUDIO ADJUST

TV SYS: B/G

VHF

LO

W

PR: 01

ATT : OFF

MANUAL PROGRAM

VOLUME: 0

TV SYS: B/G

AUTO PROGRAM

VHF LO

W

PR: 01

PRESET

SKIP:

PR02 OFF

TV SYS: B/G

COL

SYS : AUTO

ENGL I SH

AUTO PROGRAM

MANUAL PROGRAM

LANGUAGE /

:

GAME MODE

HYPER SURROUND:

OFF

MONITOR

AV OUT:

FEATURES

CONVERGENCE

BASS

80

00

80

TREBLE

BALANCE

AUDIO ADJUST

SPEAKER:

MAIN

P I CTURE

50

90

0

50

V IDEO ADJUST

COLOR

BR I GHT

HUE

SHARP

VM: HIGH

50

0

A/V CONTROL

FEATURES

Getting back to the previous menu

(except for AUTO PROGRAM)

Press V or v to move the cursor (z) to the first

line (N) of each menu, and press ENTER.

Cancelling the menu screen

Press MENU.

Notes (except for AUTO PROGRAM)

• When a menu is selected after pressing ENTER, the color of

both the menu and the menu symbol change and the cursor

(z) appears beside the first item of the menu.

• When an item on the menu is selected after pressing ENTER,

the color of the item changes.

• You can refer to the guide (

) at the bottom of the

menus (except for the and PRESET menu) for the basic

operations of the menu.

• If more than approximately 60 seconds elapse after you press a

button, the menu screen disappears automatically.

PRESET

Introducing the

menu system

You can preset TV channels, adjust the picture and sound qualities, and select some settings using the on-screen

menus. You can use the buttons on both the remote commander and the TV to operate the menus.

12

-EN

Getting Started

A / V CONTROL

DYNAM IC

SOFT

STANDARD

PERSONAL

V I DEO ADJUST

AUDIO ADJUST

MENU

ENTER

PRESET

SKIP: PR02 OFF

TV SYS: B/G

COL SYS : AUTO

ENGL I SH

AUTO PROGRAM

MANUAL PROGRAM

LANGUAGE/

:

ENTER ENTER

Changing the menu

language

If you prefer Chinese (for M61/M31 model)/Arabic

(for M91 model) to English, you can change the menu

language. You can use buttons on both the remote

commander and the TV.

1 Press U to turn on the TV.

2 Press MENU.

3 Press V or v to move the cursor (z) to the

PRESET menu ( ), and press ENTER.

4 Make sure the cursor (z) appears beside

LANGUAGE/ ( ), and press ENTER.

5 Press V/b/v/B to select ( ), and press

ENTER.

All of the menus change to Chinese (Arabic).

6 Press MENU to return to the normal screen.

MENU

13

-EN

Getting Started

You can preset TV channels easily by storing all the

receivable channels automatically. You can also preset

channels manually or disable program positions (see

page 15 ).

Presetting channels automatically

You can preset up to 100 TV channels in numerical

sequence from the program position 1. You can preset

channels automatically using the button on the TV or

the menu.

1 Press U to turn on the TV.

2 Press .

The TV starts scanning and presetting channels

automatically. When all of the receivable channels

are stored, the AUTO PROGRAM menu

disappears.

MENU

ENTER

PRESET

SKIP: PR02 OFF

TV SYS: B/G

COL SYS : AUTO

ENGL I SH

AUTO PROGRAM

MANUAL PROGRAM

LANGUAGE/

:

ENTER ENTER

Presetting channels

TV SYS:B/G

AUTO PROGRAM

VHF LO

W

PR: 01

A / V CONTROL

DYNAM IC

SOFT

STANDARD

PERSONAL

V I DEO ADJUST

AUDIO ADJUST

MENU

To preset channels automatically using

the menu

1 Press MENU.

2 Press V or v to move the cursor (z) to the

PRESET menu ( ), and press ENTER.

3 Press V or v to move the cursor (z) to AUTO

PROGRAM, and press ENTER.

Presetting channels manually

To change the program position for a channel or to

receive a channel with a weak signal which you cannot

receive by automatic presetting, preset the channel

manually.

1 Press MENU.

2 Press V or v to move the cursor (z) to the

PRESET menu ( ), and press ENTER.

3 Select your local TV system.

(1) Press V or v to move the cursor (z) to TV SYS, and

press ENTER.

(2) Press V/b/v/B until your local TV system appears

on the menu, and press ENTER.

ENTER

14

-EN

Getting Started

TV SYS:B/G

VHF

LO

W

PR: 01

ATT : OFF

MANUAL PROGRAM

ENTER ENTER

VOLUME: 0

TV SYS:B/G

VHF

LO

W

PR: 01

ATT : OFF

MANUAL PROGRAM

ENTER ENTER

VOLUME: 0

PRESET

SKIP: PR02 OFF

TV SYS: B/G

COL SYS : AUTO

ENGL I SH

AUTO PROGRAM

MANUAL PROGRAM

LANGUAGE/

:

ENTER ENTER

TV SYS:B/G

VHF

LO

W

PR: 01

ATT : OFF

MANUAL PROGRAM

ENTER ENTER

VOLUME: 0

4 Press V or v to move the cursor (z) to

MANUAL PROGRAM, and press ENTER.

5 Select the program position to which you

want to preset a channel.

(1) Make sure the cursor (z) appears beside PR, and

press ENTER.

(2) Press V/b/v/B until the program position you

want appears on the menu, and press ENTER.

6 Select the desired channel.

(1) Press V or v to move the cursor (z) to VHF LOW

(VHF Hi or UHF), and press ENTER.

(2) Press V/b/v/B until the desired channel picture

appears on the TV screen, and press ENTER.

7 Press MENU to return to the normal screen.

If the TV system is not properly selected

The picture color may be poor and/or the sound may

be noisy. In this case, select the appropriate TV system.

1 Press PROGR +/– or the number buttons to select

the program position.

2 Display the PRESET menu.

3 Press V or v to move the cursor (z) to TV SYS, and

press ENTER.

4 Press V/b/v/B until the appropriate TV system

appears, and press ENTER.

Notes

• The TV SYS (TV system), the ATT (attenuator), and the

VOLUME (volume offset) settings are memorized for each

program position.

• If you do not know your local TV system, consult your nearest

Sony dealer or authorized service center.

Attenuating the signal for individual

programs

If the TV signal is too strong, the picture may be

distorted. You can reduce the picture distortion by

attenuating the signal individually.

1 Display the PRESET menu.

2 Press V or v to move the cursor (z) to

MANUAL PROGRAM, and press ENTER.

3 Press V or v to move the cursor (z) to ATT,

and press ENTER.

4 Press V/b/v/B to select ON, and press ENTER.

15

-EN

Getting Started

Presetting the volume level for

individual programs

If the volume of the selected program is louder than

that of other programs, set the volume level.

1 Press MENU.

2 Press V or v to move the cursor (z) to the

PRESET menu ( ), and press ENTER.

3 Press V or v to move the cursor (z) to

MANUAL PROGRAM, and press ENTER.

4 Press V or v to move the cursor (z) to

VOLUME, and press ENTER.

5 Press V/b/v/B to set the level, and press

ENTER.

The level can be set as 0, –1, –2, ....–6 (minimum).

TV SYS:B/G

VHF

LO

W

PR: 01

ATT : OFF

MANUAL PROGRAM

ENTER ENTER

VOLUME: 0

PRESET

SKIP: PR02 OFF

TV SYS: B/G

COL SYS : AUTO

ENGL I SH

AUTO PROGRAM

MANUAL PROGRAM

LANGUAGE/

:

ENTER ENTER

PRESET

SKIP: PR02 OFF

TV SYS: B/G

COL SYS : AUTO

ENGL I SH

AUTO PROGRAM

MANUAL PROGRAM

LANGUAGE/

:

ENTER ENTER

A / V CONTROL

DYNAM IC

SOFT

STANDARD

PERSONAL

V I DEO ADJUST

AUDIO ADJUST

MENU

A / V CONTROL

DYNAM IC

SOFT

STANDARD

PERSONAL

V I DEO ADJUST

AUDIO ADJUST

MENU

Disabling program positions

By disabling unused or unwanted program positions,

you can skip those positions when you press PROGR

+/–.

1 Press MENU.

2 Press V or v to move the cursor (z) to the

PRESET menu ( ), and press ENTER.

3 Press V or v to move the cursor (z) to SKIP,

and press ENTER.

4 Press V or v until the unused or unwanted

program position appears on the menu,

and press ENTER.

5 Press V/b/v/B to select ON, and press ENTER.

6 To disable other program positions, repeat

steps 4 and 5.

7 Press MENU to return to the normal screen.

To cancel the skip setting

1 Display the PRESET menu.

2 Press V or v to move the cursor (z) to SKIP, and

press ENTER.

3 Press V or v until the program position you want to

cancel the skip setting appears, and press ENTER.

4 Press V/b/v/B to select OFF, and press ENTER.

16

-EN

Getting Started

Before you use the projection TV, adjust convergence.

The projection tube image appears on the screen in

three layers (red, green and blue). If they do not

converge, the color is poor and the picture blurs. To

correct this, adjust convergence.

After 20-30 minutes of turning on the power, adjust

convergence.

Adjusting the convergence

automatically

Press on the TV.

The auto convergence function works for about 30

seconds.

Adjusting the convergence manually

When the auto convergence function does not work

correctly with , adjust convergence by selecting

CONVERGENCE of the FEATURES menu.

1 Press MENU.

2 Press V or v to move the cursor (z) to the

FEATURES menu ( ), and press ENTER.

3 Press V or v to move the cursor (z) to

CONVERGENCE and press ENTER.

The CONVERGENCE adjustment screen appears.

4 Press V or v to move the cursor (z) to the

symbol showing the line you want to

adjust, and press ENTER.

: Red vertical line (left/right adjustment)

: Red horizontal line (up/down adjustment)

: Blue vertical line (left/right adjustment)

: Blue horizontal line (up/down adjustment)

R

ENTER

GAME MODE

HYPER SURROUND :

OFF

MON I TOR

AV OUT:

FEATURES

ENTER ENTER

CONVERGENCE

5 Press V or v to move the line until it

converges with the center green line, and

press ENTER.

To move up/right, press V.

To move down/left, press v.

6 Repeat steps 4 and 5 to adjust the other

lines until all three lines converge and are

seen as a white cross.

7 Press MENU to return to the normal screen.

Adjusting the

convergence

(CONVERGENCE)

R=Red

G=Green

B=Blue

R

G

B

R

G

B

R

G+B

(Light blue)

R

G+B

(Light blue)

/

17

-EN

Operations

PROGR

Watching the TV

1 Press U to turn on the TV.

When the TV is turned on in the standby mode, the

u/Â indicator on the TV lights up. To turn on the

TV completely, press u on the remote commander.

2 Select the TV program you want to watch.

To select a program position directly

Press the number button.

To select a two-digit program position, press “÷”

before the number buttons.

For example: to select program position 25, press

“÷,” then “2” and “5.”

2

-/--

5

Operations

1

2

3

4

5

6

7

8

0

-/--

9

FREEZE SWAP

PIP

PROGR

To scan through program positions

Press PROGR +/– on the remote commander or the

TV until the program position you want appears.

3 Press Á +/– on the remote commander or

the TV to adjust the volume.

Turning off the TV

To turn off the TV temporarily

Press u on the remote commander. The u/Â

indicator lights up.

To turn off the TV completely

Press U on the TV.

Operations

18

-EN

VIDEO 1 VIDEO 2 VIDEO 3 1

DVD

Displaying the on-screen information

Press .

Note

• The on-screen display shows the program position or the video

mode, the picture and sound information. The on-screen

display for the picture and sound information disappears after

being displayed for approximately three seconds.

Setting the Sleep Timer

You can set the TV to turn off automatically after the

period of time you want.

Press .

To cancel the Sleep Timer, press repeatedly until

“SLEEP TIMER: OFF” appears, or turn the TV off.

Watching the video input

Press … on the remote commander or … on

the TV.

To watch TV

Press ; on the remote commander or … on the TV.

Switching back quickly to the previous

channel

Press JUMP.

Muting the sound

Press ¤.

MUTING

POWER BASSO: ON

DYNAMIC

8

After 30 minutes

After 60 minutes

No Sleep Timer

After 90 minutes

SLEEP TIMER:30M SLEEP TIMER:60M

SLEEP TIMER:OFF SLEEP TIMER:90M

19

-EN

Operations

Press V/b

Increase picture

contrast.

Increase color

intensity.

Brighten the picture.

Make picture tones

become greenish.

Sharpen the picture.

Select HIGH to

increase emphasis on

picture edges.

P I CTURE

50

90

0

50

V I DEO ADJUST

COLOR

BR I GHT

HUE

SHARP

VM: HIGH

50

0

ENTER ENTER

Adjusting the

picture and sound

ENTER ENTER

MENU

Adjusting the picture settings

(VIDEO ADJUST)

You can adjust the picture settings to suit your taste

with the VIDEO ADJUST option. The adjusted settings

are stored in the PERSONAL option.

1 Press MENU.

2 Make sure the cursor (”) appears in the A/V

CONTROL menu ( ), and press ENTER.

3 Press V or v to move the cursor (”) to VIDEO

ADJUST, and press ENTER.

4 Press V or v to move the cursor (”) to the

item you want to adjust, and press ENTER.

5 Press V/b/v/B to adjust the selected item,

and press ENTER.

For details on each item, see “Description of adjustable

items” below.

6 To adjust other items, repeat steps 4 and 5.

7 Press MENU to return to the normal screen.

Description of adjustable items

Item Press v/B

PICTURE Decrease picture

contrast.

COLOR Decrease color

intensity.

BRIGHT Darken the picture.

HUE Make picture tones

become reddish.

SHARP Soften the picture.

VM* Select LOW to

decrease emphasis

on picture edges.

*: Each time you press V/b/v/B, the picture changes as follows:

Note

• You can adjust HUE for the NTSC color system only. (Note

that you can't adjust the NTSC color system of the component

inputs.)

n HIGH n LOW

MENU

ENTER

A / V CONTROL

DYNAM IC

SOFT

STANDARD

PERSONAL

V I DEO ADJUST

AUDIO ADJUST

MENU

A / V CONTROL

DYNAM IC

SOFT

STANDARD

PERSONAL

V I DEO ADJUST

AUDIO ADJUST

MENU

Selecting the picture and sound modes

1 Press MENU.

2 Make sure the cursor (”) appears in the A/V

CONTROL menu ( ), and press ENTER.

3 Press V or v to move the cursor (”) to

DYNAMIC, STANDARD, SOFT, or PERSONAL,

and press ENTER.

Select To

DYNAMIC Receive high contrast picture with

powerful sound.

STANDARD Receive normal contrast picture with

medium listening sound.

SOFT Receive mild picture with soft sound.

PERSONAL Receive the last picture and sound

settings that are adjusted using VIDEO

ADJUST and AUDIO ADJUST.

4 Press MENU to return to the normal screen.

Operations

20

-EN

If the picture is slightly snowy

You may try to improve the picture by changing the

VM setting as described below:

1 Display the VIDEO ADJUST menu.

2 Press V or v to move the cursor (”) to VM, and

press ENTER.

3 Press V/b/v/B to select LOW, and press ENTER.

If the picture color is abnormal when receiving

programs through the ˘ (antenna) terminal

Change the color system or the TV system from the

PRESET menu as described below until the color

becomes normal.

1 Display the PRESET menu.

2 Press V or v to move the cursor (”) to

COL SYS or TV SYS, and press ENTER.

3 Press V/b/v/B to change the color system or the

TV system until the color becomes normal, and

press ENTER.

Note

• Normally set the color system (COL SYS) to AUTO.

Adjusting the sound settings

(AUDIO ADJUST)

You can adjust the sound settings to suit your taste

with the AUDIO ADJUST option. The adjusted settings

are stored in the PERSONAL option.

1 Press MENU.

2 Make sure the cursor (”) appears in the A/V

CONTROL menu ( ), and press ENTER.

3 Press V or v to move the cursor (”) to

AUDIO ADJUST, and press ENTER.

4 Press V or v to move the cursor (”) to the

item you want to adjust, and press ENTER.

BASS

80

00

80

TREBLE

BALANCE

AUDIO ADJUST

ENTER ENTER

SPEAKER:

MAIN

Press V/b

Increase the bass

sound.

Increase the treble

sound.

Increase the right

speaker's volume.

5 Press V/b/v/B to adjust the selected item,

and press ENTER.

For details on each item, see “Description of adjustable

items” below.

6 To adjust other items, repeat steps 4 and 5.

7 Press MENU to return to the normal screen.

Description of adjustable items

Item Press v/B

BASS Decrease the bass

sound.

TREBLE Decrease the treble

sound.

BALANCE Increase the left

speaker's volume

If the sound is distorted or noisy when

receiving programs through the (antenna)

terminal

Change the TV system from the PRESET menu as

described below until the sound becomes normal.

1 Display the PRESET menu.

2 Press V or v to move the cursor (”) to TV SYS, and

press ENTER.

3 Press V/b/v/B to change the TV system until the

sound becomes normal, and press ENTER.

A / V CONTROL

DYNAM IC

SOFT

STANDARD

PERSONAL

V I DEO ADJUST

AUDIO ADJUST

MENU

La page charge ...

Sony KP-XA43M61 Le manuel du propriétaire

Ce manuel convient également à

Sony KP-XA43M61 Le manuel du propriétaire

dans d''autres langues

Documents connexes

Autres documents