Best WC35IQ90SB Guide d'installation

WC35 Series

ENGLISH.....................................2

FRANÇAIS.................................24

ESPAÑOL.................................. 47

In USA - BEST Hartford, Wisconsin

In CANADA - BEST Drummondville, QC, Canada

REGISTER YOUR PRODUCT ONLINE AT : www.BestRangeHoods.com/register

For additional Information visit www.BestRangeHoods.com

- 2 -

READ AND SAVE THESE INSTRUCTIONS

WARNING

TO REDUCE THE RISK OF FIRE, ELECTRIC SHOCK, OR INJURY TO PERSONS, OBSERVE

THE FOLLOWING:

1. Use this unit only in the manner intended by the manufacturer. If you have questions, contact

the manufacturer at the address or telephone number listed in the warranty.

2. Before servicing or cleaning unit, switch power off at service panel and lock service panel to

prevent power from being switched on accidentally. When the service disconnecting means can-

not be locked, securely fasten a prominent warning device, such as a tag, to the service panel.

3. Installation work and electrical wiring must be done by a qualified person(s) in accordance with

all applicable codes and standards, including fire-rated construction codes and standards.

4. Sufficient air is needed for proper combustion and exhausting of gases through the flue (chimney)

of fuel burning equipment to prevent backdrafting. Follow the heating equipment manufacturer’s

guidelines and safety standards such as those published by the National Fire Protection Associa-

tion (NFPA), and the American Society for Heating, Refrigeration and Air Conditioning Engineers

(ASHRAE), and the local code authorities.

5. When cutting or drilling into wall or ceiling, do not damage electrical wiring and other hidden

utilities.

6. Ducted fans must always be vented to the outdoors.

7. Do not use this unit with any separate solid-state speed control device.

8. To reduce the risk of fire, use only metal ductwork.

GROUNDING INSTRUCTIONS

This appliance must be grounded. In the event of an electrical short circuit, grounding reduces the

risk of electrical shock by providing an escape wire for the electric current. This appliance is equipped

with a cord having a grounding wire with a grounding plug. The plug must be plugged into an outlet

that is properly installed and grounded.

WARNING - Improper grounding can result in a risk of electric shock.

Consult a qualified electrician if the grounding instructions are not completely understood, or if doubt

exists as to whether the appliance is properly grounded.

Do not use an extension cord. If the power supply cord is too short, have a qualified electrician install

an outlet near the appliance.

!

INTENDED FOR DOMESTIC COOKING ONLY

!

- 3 -

!

CAUTION

1. For indoor use only.

2. To reduce risk of fire and to properly exhaust air, be sure to duct air outside. Do not vent exhaust

air into spaces within walls or ceilings or into attics, crawl spaces, or garages.

3. Take care when using cleaning agents or detergents.

4. Avoid using food products that produce flames under the Range Hood.

5. For general ventilating use only. Do not use to exhaust hazardous or explosive materials and

vapors.

6. To avoid motor bearing damage and noisy and/or unbalanced impellers, keep drywall spray,

construction dust, etc. off power unit.

7. Your hood motor has a thermal overload which will automatically shut off the motor if it becomes

overheated. The motor will restart when it cools down. If the motor continues to shut off and

restart, have the hood serviced.

8. For best capture of cooking impurities, the bottom of the hood should be a minimum of 24”

and a maximum of 30” above the cooking surface. See “Install Mounting Bracket” section for

mounting restrictions.

9. Two installers are recommended because of the large size and weight of this hood.

10. This product is equipped with a thermostat which may start blower automatically. To reduce

the risk of injury and to prevent power from being switched on accidentally, switch power off at

service panel and lock or tag service panel.

11. Please read specification label on product for further information and requirements.

12. EXTERNAL BLOWER MODELS ONLY: To reduce the risk of fire and electric shock, install this

range hood only with Best Exterior Blower Models EB6, EB9, EB12 or EB15 or Best In-Line

Blower Models ILB3, ILB6, ILB9 or ILB11. Other blower cannot be substituted. Blowers sold

separately.

WARNING

TO REDUCE THE RISK OF A RANGE TOP GREASE FIRE:

A. Never leave surface units unattended at high settings. Boilovers cause smoking and greasy

spillovers that may ignite. Heat oils slowly on low or medium settings.

B. Always turn hood ON when cooking at high heat or when flambeing food (i.e. Crepes Suzette,

Cherries Jubilee, Peppercorn Beef Flambé).

C. Clean ventilating fans frequently. Grease should not be allowed to accumulate on fan or filter.

D. Use proper pan size. Always use cookware appropriate for the size of the surface element.

TO REDUCE THE RISK OF INJURY TO PERSONS IN THE EVENT OF A RANGE TOP GREASE

FIRE, OBSERVE THE FOLLOWING:*

1. SMOTHER FLAMES with a close-fitting lid, cookie sheet, or metal tray, then turn off the burner.

BE CAREFUL TO PREVENT BURNS. If the flames do not go out immediately, EVACUATE AND

CALL THE FIRE DEPARTMENT.

2. NEVER PICK UP A FLAMING PAN - You may be burned.

3. DO NOT USE WATER, including wet dishcloths or towels - violent steam explosion will result.

4. Use an extinguisher ONLY if:

A. You know you have a Class ABC extinguisher and you already know how to operate it.

B. The fire is small and contained in the area where it started.

C. The fire department is being called.

D. You can fight the fire with your back to an exit.

* Based on “Kitchen Fire Safety Tips” published by NFPA.

- 4 -

OPERATION

Controls (Fig. 1)

HEAT SENTRY™

Your hood is equipped with a HEAT SENTRY™ thermostat. This thermostat is a

device that will turn on or speed up the blower if it senses excessive heat above

the cooking surface.

1) If blower is OFF - it turns blower ON to HIGH speed.

2) If blower is ON at a lower speed setting - it turns blower up to HIGH speed.

When the temperature level drops to normal, the blower will return to its original setting.

WARNING

The HEAT SENTRY thermostat can start the blower even if the hood is turned OFF. When

this occurs, it is impossible to turn the blower OFF with its switch. If you must stop the

blower, do it from the main electrical panel.

Light

Switch

Blower

On / Off

Blower

Speed 2

Time

Delay

FIG. 1

Blower

Speed 3

Blower

Speed 4

Filter

Reset

This range hood is equipped with the latest in capacitive touch technology. The buttons do

not move, but are touch-sensitive. When a touch is understood, the control will emit a sound.

Light Button turns the LED lights on and off. Push once to turn lights on. Push again to turn

lights off.

Blower On / Off button turns the blower on to low speed. Push a second time to turn blower off.

Blower Speed 2 button increases blower speed to medium-low speed.

Blower Speed 3 button increases blower speed to medium-high speed.

Blower Speed 4 button increases blower speed to high speed.

Delay button activates a delay off feature. Press once to activate the 5-minute delay off for any

of the blower speed settings. Press again to deactivate the time delay off.

Filter Reset lights after every 30 hours of operation, indicating a need to clean the filters. After

filters are cleaned or replaced, press once to reset the 30-hour timer.

Clean Mode deactivates controls for cleaning of glass. Press and hold and

for

5 seconds. Repeat to re-activate controls.

Auto Shut-Off Feature

If the blower and/or the lights are on continuously for 10 hours without any user interaction with

the controls, the hood will automatically shut off. Press any control button to re-activate the hood.

- 5 -

LED LAMPS

The hood is provided with LED lamps which require no maintenance.

CLEANING AND MAINTENANCE

Proper maintenance of the Range Hood will assure proper performance of the unit.

Motor

The motor is permanently lubricated and never needs oiling. If the motor bearings make excessive or

unusual noise, replace the motor with the exact service motor. The impeller should also be replaced.

Grease Filter

The grease filter should be cleaned frequently. Use a warm detergent solution. Grease filter is dishwasher

safe.

Clean all-metal filters in the dishwasher using a non-phosphate detergent. Discoloration of the filter may

occur if using phosphate detergents, or as a result of local water conditions - but this will not affect filter

performance. This discoloration is not covered by the warranty.

See “INSTALL FILTERS” section for removal and installation instructions.

Non-ducted Recirculation Filter

The non-ducted recirculation filter should be changed every 6 months. Replace more often if your

cooking style generates extra grease, such as frying and wok cooking. See “INSTALL FILTERS” section

for removal and installation instructions.

Stainless Steel Cleaning

DO:

• Regularlywashwithcleanclothorragsoaked

with warm water and mild soap or liquid dish

detergent.

• Alwayscleaninthedirectionoforiginalpolish

lines.

• Alwaysrinsewellwithclearwater(2or3times)

after cleaning. Wipe dry completely.

•  Yo u  may also use a specialized household

stainless steel cleaner.

DON’T:

•

Use any steel or stainless steel wool or any

other scrapers to remove stubborn dirt.

• Useanyharshorabrasivecleansers.

• Allowdirttoaccumulate.

• Let plaster dust or any other construction

residues reach the hood. During construction/

renovation, cover the range hood to make sure

no dust sticks to the stainless steel surface.

Avoid: When choosing a detergent

• Anycleanersthatcontainbleachwillattackstainlesssteel

• Anyproductscontaining:chloride,fluoride,iodide,bromidewilldeterioratesurfacesrapidly.

• Anycombustibleproductsusedforcleaningsuchasacetone,alcohol,ether,benzol,etc.,arehighly

explosive and should never be used close to a range.

- 6 -

PREPARE THE HOOD

Unpack hood and check contents.

You should receive:

1 - Hood

1 - Decorative Flue Assembly

1 - Parts Bag containing:

2 - Mounting Brackets

1 - Damper Kit

1 - Flue Mounting Bracket Assembly

8 - Mounting Screws (4.8 x 38mm Pan Head)

4 - Mounting Screws (3.9 x 9.5mm Pan Head)

2 - Mounting Screws (3.9 x 6mm Flat Head)

8 - Drywall Anchors

2 - Flat Washers

1 - Filter Support

4 - Mounting Screws (4 x 8mm)

1 - Installation Instructions

MOUNTING

BRACKETS

FLUE MOUNTING BRACKET

8 MOUNTING SCREWS

(4.8 x 38mm Pan Head)

8 DRYWALL

ANCHORS

4 MOUNTING

SCREWS (3.9 x

9.5mm Pan Head)

DECORATIVE

FLUE

2 MOUNTING

SCREWS (3.9 x

6mm Flat Head)

FIG. 2

2 FLAT

WASHERS

DAMPER KIT

FILTER SUPPORT & (4)

MOUNTING SCREWS

(4 X 8mm)

- 7 -

EXTERIOR OR IN-LINE BLOWER SELECTION (WC35E)

CAUTION: Either an exterior blower or in-line blower may be used with this hood.

The hood must be installed with blower models EB6, EB9, EB12, EB15, ILB3,

ILB6, ILB9, or ILB11 only. Other Blowers cannot be substituted (Blowers sold

separately).

DECORATIVE

FLUE

8” ROUND

DUCT

INSTALL THE DUCTWORK

NOTE: To reduce the risk of fire, use only metal ductwork.

1. Choose the location where the Exterior or In-Line Blower will be mounted. See

illustrations below for mounting location suggestions and restrictions.

2. A straight, short duct run will allow the hood to perform most efficiently.

3. Long duct runs, elbows and transitions will reduce the performance of the

hood. Use as few of them as possible. Larger ducting may be required for best

performance with long duct runs.

4. After the Exterior or In-Line Blower has been installed, connect round metal

ductwork and work back towards the hood location. Use duct tape to seal joints

between ductwork sections.

5. An 8” round to 10” round transition (Model 414) is required. For best air

performance, install the transition as close to the range hood as possible.

OK

SUGGESTED MOUNTING LOCATIONS

EXTERIOR BLOWER

CAUTION: MAY NOT FIT

UNDER EAVES OF SINGLE

STORY HOMES

EXTERIOR

BLOWER

10” ROUND

DUCT

EXTERIOR

BLOWER

8” TO 10”

ROUND

TRANSITION

8” ROUND

ELBOW

10”

ROUND

DUCT

HOOD

24” TO 30” ABOVE

COOKING SURFACE

4¼” DISTANCE FROM

CENTERLINE OF DUCT

TO DRYWALL

- 8 -

IN-LINE BLOWER

- 9 -

ROOF CAP

8-INCH

ROUND DUCT

DECORATIVE

FLUE

HOOD

WALL

CAP

8-INCH

ROUND

ELBOW

24” TO 30”

ABOVE

COOKING

SURFACE

(see “INSTALL

MOUNTING

BRACKETS”

section for

mounting

restrictions)

4¼”

DISTANCE

FROM

CENTERLINE

OF DUCT TO

DRYWALL

INSTALL THE DUCTWORK

DUCTED HOODS ONLY

CAUTION: To reduce the risk of fire, use

only metal ductwork.

1. Decide where the ductwork will run be-

tween the hood and the outside. Fig. 3.

2. A straight, short duct run will allow the

hood to perform most efficiently.

3. Long duct runs, elbows, and transitions

will reduce the performance of the hood.

Use as few of them as possible. Larger

ducting may be required for best perfor-

mance with longer duct runs.

4. Install a roof or wall cap. Connect round

metal ductwork to cap and work back

towards hood location. Use duct tape to

seal the joints between ductwork sections.

INSTALL ELECTRICAL

DUCTED and NON-DUCTED HOODS

WARNING : Electrical wiring must

be done by a qualified person(s) in ac-

cordance with all applicable codes and

standards. This range hood must be prop-

erly grounded. Turn off electrical power at

service entrance before wiring.

1. Plan where the hood will be located

above the cook top. Refer to the “INSTALL

MOUNTING BRACKET” section for hood

mounting height options.

2. Install a standard 2” x 4” wall outlet box

and 3-blade 125 volt, 15 Amp grounded

receptacle. Fig. 4.

3. Mount the center of the wall outlet 18½”

to 19½” above the bottom of the hood.

4. Locate the box and the receptacle within

boundary shown and off center of the

ductwork (to allow for power cord plug

and flue clearance).

FIG. 4

18½” to 19½”

4”

8”

CENTERLINE

OF HOOD

FIG. 3

- 10 -

EXTERNAL BLOWER ELECTRICAL CONNECTIONS

Blower connection at hood:

1. Run 2-wire plus ground power cable from

the Exterior or In-Line Blower to the hood’s

wiring box marked “motor connection”.

2. Remove the cover from the wiring box and

remove one knockout.

3. Feed 6” of cable through the knockout

opening and secure the cable to the wiring

box with an appropriate connector.

4. Make electrical connections at the hood.

Connect white-to-white, red-to-black and

green-to-ground.

5. Replace the wiring box cover and screws.

make sure wires are not pinched between

the cover and box.

Exterior or In-line blower connection:

1. Make electrical connections at the exterior

or in-line blower (see instructions provided

with the exterior or in-line blower).

Power connection at hood:

1. Plug the power cord into the electrical wall

receptacle.

BLOWER CONNECTION AT HOOD

BOX MARKED

“MOTOR

CONNECTION”

CONNECT:

WHITE-TO-WHITE,

RED-TO-BLACK,

GREEN-TO-GROUND.

Exterior or

In-Line blower

FIG. 5

- 11 -

INSTALL MOUNTING

BRACKETS

DUCTED and NON-DUCTED HOODS

1. Construct wood wall framing that is flush

with interior surface of wall studs. Fig. 6.

Make sure:

a) the framing is centered over installa-

tion location.

b) the height of the framing will allow the

mounting brackets to be secured

to the framing within the dimensions

shown.

2. After wall surface is finished, secure

the mounting brackets to framing with (4)

4.8 x 38 mm mounting screws. See chart

below for mounting bracket location.

Notes:

a. Minimum hood distance above cook top must not be less than 24”. A maximun of 30” above

cook top is highly recommended for best capture of cooking impurities. Distances over 30”

are at the installer and user’s discretion; and if ceiling height and flue length permit.

b. Requires optional 10’ flue extension, ducted model AEWC345

IQSB or non-ducted model

AEWC345IQSBN.

HOOD DISTANCE ABOVE 36” HIGH COOK TOP (see note below)

30”

MOUNTING BRACKET CENTER HOLE LOCATION ABOVE 36” HIGH COOK TOP

CEILING

HEIGHT

8 FEET

24” 25” 26” 27” 28” 29”

37-7/8” 38-7/8” 39-7/8” 40-7/8”

9 FEET

41-7/8”

42-7/8” 43-7/8”

DUCTED

NON-DUCTED

DUCTED OR

NON-DUCTED

DUCT

METHOD

37-7/8” 38-7/8” 39-7/8” 40-7/8”

40-7/8” 41-7/8”

42-7/8” 43-7/8”

10 FEET (see note b.)

39-7/8” 40-7/8” 41-7/8”

42-7/8” 43-7/8”

37-7/8” 38-7/8”

INSTALL CENTER BRACKET

1. Install center bracket using (4) M4x8

screws. Fig. 7.

FIG. 7

(4) M4x8

SCREWS

CENTER

BRACKET

41-7/8”

42-7/8” 43-7/8”

WOOD CROSS

SUPPORT BEHIND

DRYWALL

FIG. 6

FRAMING

BEHIND WOOD

CROSS SUPPORT

CENTERLINE

3-1/2”

2-3/16”

---

- 12 -

INSTALL FLUE MOUNTING

BRACKET

DUCTED AND NON-DUCTED HOODS

1. Assemble the flue mounting brack-

et, adjusting outside width as shown.

Fig. 8.

2. Carefully center the mounting bracket

directly over the range hood location.

3. Secure the bracket assembly to the

ceiling using (2) 4.8 x 38 mm mount-

ing screws and drywall anchors.

Fig. 9. Make sure the bracket is pushed

into the corner, tight against the wall and

centered over the hood.

FLUE MOUNTING BRACKET

11¾”

FIG. 8

3.9 x 6 mm FLAT HEAD

BRACKET SCREWS

FIG. 9

4.8x38mm

MOUNTING SCREWS

DRYWALL ANCHORS

FIG. 11

INSTALL THE HOOD

Note: Remove the plastic protective film

from all exterior surfaces, decorative

flues and filters, prior to final installation.

Remove filters. (Refer to the “Install Filters”

Section.)

DUCTED and NON-DUCTED INSTALLATION

1. Remove the electrical system box from

chimney frame by removing (2) 3.9 x 9.5 mm

screws. Fig. 10.

2. Attach electrical system box to frame using (2)

3.9 x 9.5 mm screws removed in Step 1 and

(2) 3.9 x 9.5 mm screws and (2) lock washers

from hardware bag.

3. Install hood onto the wall mounting brackets.

Fig. 11. Adjust leveling screws on mounting

brackets to level hood with floor.

3. Mark and install (2) additional screws as

shown. Use drywall anchors only if necessary.

ELECTRICAL

SYSTEM BOX

FIG. 10

REMOVE (2)

3.9 x 9.5 mm

SCREWS

4.8 x 38 mm

SCREWS

INSTALL (4)

3.9 x 9.5 mm

SCREWS &

LOCK WASHERS

ON (2) SCREWS

- 13 -

FIG.12

8-INCH DIA.

METAL DUCT

DUCTED INSTALLATION ONLY

Note: Rooms with 10-foot ceiling require

flue extension model AEWC345

I QSB,

available from your local dealer. Discard

the upper flue supplied with the range

hood and replace it with the longer flue

extension.

1. Remove protective tape from blower outlet

before installing damper to hood with

(4) screws supplied and tape joint with

aluminum duct tape. Fig. 12.

2. Run 8-inch diameter metal ductwork to

the outside location.

3. Install an appropriate wall or roof cap with

damper to exhaust the air to the outside.

4. Tape all duct joints with aluminum duct

tape.

5. Plug power cord into wall outlet. Fig. 13.

6. Install upper and lower decorative flues

onto the range hood.

- Vents are concealed on 8-foot

ceilings.

- Vents are exposed on 9-foot

ceilings.

7. Secure upper flue to flue mounting bracket

with (2) 3.9 x 6 mm screws. Fig. 14

FIG.13

FIG.14

DAMPER/

DUCT

CONNECTOR

CONCEALED

VENTS

CEILING

3.9 x 6mm

SCREWS

2

- 14 -

NON-DUCTED INSTALLATION ONLY

Note:

a. Purchase Model ANKWC345 Non-ducted

Recirculation Kit.

b. Rooms with 10-foot ceiling require flue

extension model AEWC345

IQSBN,

available from your local dealer. Discard

the upper flue supplied with the range

hood and replace it with the longer flue

extension.

1. Install discharge collar supplied with the

range hood. Fig. 15.

2. Attach the 6”-to-8” adapter to blower

discharge and tape joint with aluminum

duct tape. Fig. 15.

3. Install the plenum to the upper decorative

flue using (4) 3.4 x 15 mm screws

provided as shown. Fig. 16.

4. Attach 6-inch expandable ducting to the

plenum and tape joint with aluminum duct

tape. Fig. 17.

5. Attach non-duct filter frame using (4) 3.9

x 6 mm screws. Fig. 18.

FIG.15

FIG.16

FIG.17

3.9 x 6mm

SCREWS

FIG.18

- 15 -

6. Temporarily secure the upper and lower

flue together with duct tape as shown. Fig.

19.

7. Lift the flue into position above the hood.

Secure upper flue to the flue mounting

bracket with (2) 3.9 x 6 mm screws. Fig.

20.

8. Stretch expandable duct, attach it to the

6”-to-8” adapter and tape duct joints. Fig.

2 1.

9. Plug power cord into wall outlet.

10. Remove tape from flues and lower into

position on the hood. Fig. 22.

FIG.20

FIG.19

FIG.21 FIG.22

3.9 x 6mm

SCREWS

2

- 16 -

INSTALL FILTERS

DUCTED AND NON-DUCTED HOODS

1. To remove the GREASE filter, pull down

latch tab to disengage the filter from the

hood. Tilt the filter downward and remove.

Fig. 23.

2. To install the GREASE filter, align rear filter

tabs with slots in the hood. Pull down latch

tab, push filter into position and release.

Make sure the filter is securely engaged

after installation. Fig. 24.

NOTE: Prior to use, remove protective film

from the filter frame.

NON-DUCTED HOODS ONLY

1. To remove the CHARCOAL filter, grip and

push filter tab toward rear of hood. Pull the

filter down to disengage the rear filter tabs.

Fig. 23.

2. To install the CHARCOAL filter, align filter

in rectangular opening. Push filter against

springs in rear of hood and press into place.

Make sure the filter is securely engaged

after assembly.

3. Install GREASE filter after charcoal filter

is installed.

FIG.23

FIG.24

- 17 -

CALIBRATE IQ BLOWER

SYSTEM

TM

INTERNAL BLOWER DUCTED UNITS ONLY

After the hood is installed and wired, en-

gage the calibration process (our Guaran-

teed Performance System Technology to

ensure full-rated airflow is being delivered).

Prior to calibration, ensure that all filters,

light bulbs and duct system are installed.

CALIBRATION PROCESS Fig. 25.

Hold the calibration button for 3 seconds;

calibration button will light up and stay on

for up to 13 minutes. The blower will start

and begin the calibration process. When

calibration is complete, one of two things

will occur:

A. The blower turns off and calibration but-

ton light turns off = Successful calibra-

tion.

B. The blower turns off and calibration but-

ton light blinks continuously = Too much

restriction in the ductwork is preventing

the IQ Blower System™ from achieving

the rated airflow. The blower is automati-

cally set to maximum intensity.

NOTE: Common items that cause restric-

tions: restricted damper flap (backdraft

damper, wall cap, roof cap), too many

elbows, duct size less than 80% of hood

outlet, poor transition, use of flex ducting

and/or crushed ducting.

Two options are available:

1. Press the calibration button to accept

airflow as is. The IQ Blower System™

is now configured to its highest possible

setting. The blinking calibration light

goes out.

2. Correct duct restriction and repeat the

calibration process.

a. To clear the original calibration data,

hold calibration button for 10 seconds.

The light will blink 3 times to confirm

and the blower configuration will go

back to default settings.

b. Repeat calibration process.

FIG.25

CALIBRATION

BUTTON

CALIBRATION

LIGHT

- 18 -

The range hood is designed to work with

several different blower models. Before

using, the control must first be programmed

to your blower model, in order to achieve

proper operating speeds.

From the chart below:

1. Find the SETUP number that

corresponds to the blower model that is

installed with your range hood.

2. The control is factory-preset to SETUP

3. If your blower model is listed under

SETUP 3, no programming is required

and the range hood is ready to use.

SETUP SETUP SETUP

(default)

BLOWER

MODEL

NUMBER

EB6

ILB3

ILB6

EB12

EB15

ILB9

EB9

ILB11

3. To program blower models listed under

SETUP 1 and 2:

A) Power must be supplied to the

hood. The blower and lights must be

turned off.

B) Press and hold

for 5 seconds.

+

will flash 3

times. After 1 second, ,

or will light up to indicate the

current setting.

C) Select the proper SETUP for your

blower from the chart at left. Press

, or to select the

proper SETUP. Then press to

confirm and store the new setting.

D) The range hood is now ready to use.

EXTERNAL BLOWER

PROGRAMMING MODE PROCEDURE (WC35E)

Light

Switch

Blower

On / Off

Blower

Speed 2

Time

Delay

FIG. 26

Blower

Speed 3

Blower

Speed 4

Filter

Reset

- 19 -

SERVICE PARTS

WC35IQ SERIES

KEY NO. DESCRIPTION PART NO.

CAS BLOWER ASSEMBLY 06002259

49 FAN (CLOCK WISE) 03295071

IME ELECTRICAL INSTALLATION ASSEMBLY 06145222

114 RUNNER WIRES 032904990

506 BLDC DRIVER 97019431

67 WIRES 06102592

202 REFLECTOR STOP 03292290

415 FAIRLEAD 03202288

60 FEEDER CABLE 02300249

415 FAIRLEAD 03202288

37 KNOB 02300804

474 LED LAMP 08093413

AQI SWITCH BOX ASSEMBLY 06102590

439 STOP RING 02320034

507 WIRE CALIBRATION BUTTON 06102584

195 BRACKET E3351078

9 GREASE FILTER 08087823

ARU CONNECTION AIR OUTLET SET 080810849

485 TELESCOPIC DUCT KIT 08016368

120 FLUE MOUNTING BRACKET 08091851

195 CENTER BRACKET E3351078

122 NON-DUCT PLENUM 08093478

86 6” ADAPTER RING 032292300

503 6” EXPANDABLE DUCT 02011557

58 8” TO 6” REDUCER 03294170

- 20 -

SERVICE PARTS

WC35IQ SERIES

474

485

64

US-DUNE HS BLDC

195

CAS

IME

506

202

60

202

415

(03202288)

415

(03202288)

49

114

AQI

9

120

503

86

122

67

ARU

439

37

507

58

La page charge ...

Best WC35IQ90SB Guide d'installation

Ce manuel convient également à

Best WC35IQ90SB Guide d'installation

dans d''autres langues

Documents connexes

Autres documents