WilsonPro Pro 1000R Guide d'installation

Taper
Guide d'installation
ENGLISH FRANÇAIS
A Wilson Electronics Brand
wilsonpro.com 866.294.1660
User Manual
In-Building Signal Booster
With Extended Dynamic Range
WILSON PRO
1000R
Package Content
1
About The WilsonPro 1000R
2
Key Features
4
Competitive Advantages
5
Post Install Setup
7
Status Screen
8
Band Status Screens
10
Safety Guidelines
12
Warranty
16
Index
1
WILSON PRO 1000R IN-BUILDING SIGNAL BOOSTER
EN
WilsonPro
1000R
2’ Wilson
400
Lightning Surge
Protector
Wide Band Directional
Antenna + 75’
Wilson 400 Cable
Dome Antenna +
100’ Wilson 400 Cable
Package
Content
Kit 460231
2
IN-BUILDING SIGNAL BOOSTER WILSON PRO 1000R
EN
Easy Rack-Mounted
Installation
Neat and clean installation while leaving
the unit easily accessible.
Color LCD For Easier
Access
Unlike other boosters, the WilsonPro
1000R has a color LCD screen
with four-way navigation, allowing
integrators to have easy and e ective
control of the product.
Extended Dynamic
Range For Continuous
Connectivity
XDR allows the booster to never shutdown
due to too strong of a signal. No matter how
strong, the booster will never overpower and
shutdown.
WilsonPro 1000R
Onboard Software For
Better Control
Automatically controlled with onboard
software, ensuring great connectivity
throughout large spaces and multi-story
buildings.
3
WILSON PRO 1000R IN-BUILDING SIGNAL BOOSTER
EN
Designed to provide enhanced
in-building cellular coverage for
all commercial spaces, including
hospitals, hotels, warehouses and o ces, the WilsonPro 1000R amplifi es
weak cell signals to provide reliable voice and data coverage–including 4G – to inside
spaces where signals may not penetrate.
Like all WilsonPro cellular signal boosters, the WilsonPro 1000R features cell site
protections that auto-detect and prevent any cell tower interference.
Unlike other boosters, the WilsonPro 1000R has a color LCD screen with four-way
navigation, allowing integrators to have easy and e ective control of the product.
The 1000R is intended to fi t into an existing server rack. This design allows for a neat
and clean installation while leaving the unit easily accessible.
XDR gives the 1000R the greatest tolerance of any competing booster for a strong
incoming signal from the tower. XDR allows the booster to never shutdown due to
too strong of a signal. No matter how strong, the booster will never overpower and
shutdown.
The 1000R provides cellular coverage for all commercial spaces
4
IN-BUILDING SIGNAL BOOSTER WILSON PRO 1000R
EN
Easy rack-mounted installation: The 1000R is intended to fi t into
an existing server rack. This design allows for a neat and clean
installation while leaving the unit easily accessible.
Onboard Software for Better Control: Booster is automatically
controlled with automatic onboard software, ensuring great
connectivity throughout large spaces and multi-story buildings.
The booster will adjust its gain level up or down as required by the
conditions of the immediate signal environment.
Extended Dynamic Range (XDR) for continuous connectivity: Gives
the 1000R much greater tolerance than any competing booster for
a strong incoming signal from the tower. XDR lets the 1000R system
work with an incoming signal stronger than any competing booster
and never shuts down due to a strong outside signal.
Color LCD for Easier Access: Unlike other boosters, the Wilson
1000R has a color LCD screen with four-way navigation, allowing
integrators to optimize antenna position and maximize the
performance of the booster.
Key Features
5
WILSON PRO 1000R IN-BUILDING SIGNAL BOOSTER
EN
Highest Downlink Power: Up to +15dB more downlink power than
the competition allows for stronger signal in environments where
the incoming signal is weak. The benefi t is a stronger signal sent to
the inside antennas, providing larger coverage area from a single
booster.
Highest Uplink Power: This allows for a stronger signal transmitted
to the tower, up to +3dB more than the competition, providing greater
user capacity and increased range from the cell site.
Lower Overload and Shutdown Threshold: No matter how strong
the outside signal, the WilsonPro 1000R never shuts down. This is a
huge benefi t in strong signal environments like cities and locations
close to a carrier tower.
Intelligent Control: WilsonPro cellular boosters automatically adjust
signal gain while still providing even signal coverage throughout the
building.
Sophisticated Software: Cellular signals are constantly fl uctuating.
The software is always monitoring signal levels and making
immediate adjustments as needed, allowing the booster to operate at
maximum gain consistently.
Competitive
Advantages
6
IN-BUILDING SIGNAL BOOSTER WILSON PRO 1000R
EN
Outside
Directional
Antenna
Inside Dome
Antenna(s)
1000R
Lightning
Surge Protector
The direction of the
outside antenna should
be adjusted until the
“DL” bar is maximized.
A Wilson Lightning Surge Protector is recommended for all building installations. Make
sure the protector is installed outside the building at point of entry connected to a
suitable ground and in line between the Outside Antenna and the Signal Booster.
Installation
Diagram
7
WILSON PRO 1000R IN-BUILDING SIGNAL BOOSTER
EN
The WilsonPRO 1000R is designed with advanced internal programming, which allows
it to automatically adjust for a variety of conditions, while still boosting weak signals.
Once the AC power cable and antenna cables are connected, turn the unit on by
toggling the power switch located near the AC power receptacle, located at the rear
of the unit.
Power Switch
Post Install
Setup
8
IN-BUILDING SIGNAL BOOSTER WILSON PRO 1000R
EN
The 1000R takes about 20 seconds to boot up. Once boot up is complete, the status
screen will appear, showing the amplifi cation and status of each port and band.
A solid green light
indicates that
a band is operating correctly with
maximum allowable gain.
A solid yellow light indicates band gain
reduction because of an oscillation
condition. Reposition antennas
(more separation between indoor
and outdoor antennas, and pointed
in opposite directions) and reboot
(power cycle) the 1000R for maximum
performance. When adequate
separation is achieved, the yellow
lights will return to green upon reboot.
Note that when the light is yellow,
the band is operational; however,
performance is reduced.
System Status Screen
Splash Screen
Status Screen
Lights Description
9
WILSON PRO 1000R IN-BUILDING SIGNAL BOOSTER
EN
A red light indicates a band which has
been completely shut down because
of a severe oscillation condition or
repeated oscillation events. Reposition
antennas (more separation between
indoor and outdoor antennas, and
pointed in opposite directions) and
then reboot (power cycle) the 1000R
to reactivate the band and maximize
performance. When adequate
separation is achieved, the red light(s)
will return to green upon reboot.
(LIGHTS DESCRIPTION cont.)
10
IN-BUILDING SIGNAL BOOSTER WILSON PRO 1000R
EN
This screen provides specifi c band
and port information. Including the
strength of the received uplink and
downlink signal, status details, and
the amplifi er gain.
By pressing enter on a highlighted light,
as shown, a more detailed status screen
will be displayed for the
highlighted band.
D-Pad with Enter
button
Status Screen
Close-up
Band Details Screen
Band Status Screens
Green Light
11
WILSON PRO 1000R IN-BUILDING SIGNAL BOOSTER
EN
In the presence of a strong outdoor
cell tower signal, the 1000R will
reduce it’s “boost” (Gain) using
internal Automatic Gain Control (AGC).
This gain reduction is necessary to
stay within FCC requirements. When
this occurs, the 1000R has reached
the ‘speed limit’ so this is good!
The outside antenna should always
be adjusted until the “DL” bar is
maximized and “AGC” is indicated, if
possible with a weak outside signal,
this may not be possible.
Band Details Screen
This screen indicates band gain
has been reduced because of the
oscillation condition detected at a
nearby band.
Pressing enter on a highlighted light
with a yellow light (Band 12), as shown,
will display the following...
D-Pad with Enter
button
Status Screen
Close-up
Band Details Screen
(BAND STATUS SCREENS - GREEN LIGHT cont.)
Yellow Light
12
IN-BUILDING SIGNAL BOOSTER WILSON PRO 1000R
EN
Warnings
To uphold compliance with network protection standards, all active cellular devices must maintain at
least 6 feet of separation distance from Panel and Dome antennas.
Use only the power supply provided in this package. Use of a non-Wilson Electronics product may
damage your equipment.
The Signal Booster unit is designed for use in an indoor, temperature-controlled environment (less than
100 degrees Fahrenheit). It is not intended for use in attics or similar locations subject to temperatures
in excess of that range.
RF Safety Warning: Any antenna used with this device must be located at least 8 inches from all persons.
AWS Warning: The Outside Antenna must be installed no higher than 10 meters (31’9”) above ground.
This device complies with Part 15 of FCC rules. Operation is subject to two conditions: (1) This device may not cause harmful
interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
Changes or modifications not expressly approved by weBoost could void the authority to operate this equipment.
FOR MORE INFORMATION ON REGISTERING YOUR SIGNAL BOOSTER WITH YOUR
WIRELESS PROVIDER, PLEASE SEE BELOW:
Sprint: http://www.sprint.com/legal/fcc_boosters.html
T-Mobile/MetroPCS: https://support.t-mobile.com/docs/DOC-9827
Verizon Wireless: http://www.verizonwireless.com/wcms/consumer/register-signal-booster.html
AT&T: https://securec45.securewebsession.com/attsignalbooster.com/
U.S. Cellular: http://www.uscellular.com/uscellular/support/fcc-booster-registration.jsp
This is a CONSUMER device.
BEFORE USE, you MUST REGISTER THIS DEVICE with your wireless provider and have
your provider’s consent. Most wireless providers consent to the use of signal boosters.
Some providers may not consent to the use of this device on their network. If you are
unsure, contact your provider.
In Canada, BEFORE USE you must meet all requirements set out in ISED CPC-2-1-05.
You MUST operate this device with approved antennas and cables as specifi ed by the
manufacturer. Antennas MUST be installed at least 20 cm (8 inches) from (i.e., MUST
NOT be installed within 20 cm of) any person.
You MUST cease operating this device immediately if requested by the FCC (or ISED in
Canada) or licensed wireless service provider.
WARNING. E911 location information may not be provided or may be inaccurate for calls
served by using this device.
This device may be operated ONLY in a fi xed location (i.e..may operate in a fi xed location
only) for in-building use.
Safety Guidelines
13
WILSON PRO 1000R IN-BUILDING SIGNAL BOOSTER
EN
The following accessories are certifi ed by the FCC to be used with the
Wilson PRO 1000R.
Inside Antenna Expansion Kit
Kit 309900-50N40090
2 - Wall Panel antennas
1 - 50 ohm 3-Way Splitter
1 - 100' Wilson 400
Kit 309905-50N17420
3 - Wall Panel Antennas
3 - 2-Way 50 Ohm Splitters
20' RG174
Kit 309902-75F0650
2 - Wall Panel Antennas
1 - 3-Way 75Ohm Splitter
50' RG6
Kit 309903-75F1180
3 - Wall Panel Antennas
3 - 2-Way 75Ohm Splitters
80' RG11 cable
Kit 309904-75F5830
1 - Wall Panel Antenna
1 - 2-Way 75 Ohm Splitter
30' RG58 cable
Inside Antenna Kits
Kit 311155-0670
75 Ohm Wall mount Panel Antenna
70’ RG6 Cable
Kit 311135-5840
50 Ohm Wall mount Panel Antenna
40’ RG58 Cable
Kit 311135-400150
50 Ohm Wall mount Panel Antenna
150' Wilson 400
Kit 311155-11120
75 Ohm Wall mount Panel Antenna
10’ RG11 cable
Kit 304412-400100
50 Ohm 4G Dome Antenna
100' Wilson400 cable
Kit 304412-5830
50 Ohm 4G Dome Antenna
30' RG58 cable
Kit 304419-1175
75 Ohm 4G Dome Antenna
75' RG 11 cable
Kit 304419-17450
75 Ohm 4G Dome Antenna
50' RG174 cable
May need separate adapter
Kit 304419-0650
75 Ohm 4G Dome Antenna
50' RG6 cable
50 Ohm Outside Antenna Kits
Kit 314453-5825
50 Ohm Pole Mount Panel Antenna
25’ RG58 Cable
Kit 314411-5825
50 Ohm Wide Band Directional
25’ RG58 Cable
Kit 301111-5850
Yagi Directional Antenna
50’ RG58 Cable
Kit 311203-5820
Omni-Directional antenna
20’ RG58 Cable
Kit 314411-40075
50 Ohm Wide Band Directional
75’ LMR400 Cable
Kit 311203-40020
Omni-Directional antenna
20’ LMR400 Cable
Kit 301111-400170
Yagi Directional w/ N-Female
170’ LMR400
Kit 314453-40075
50 Ohm Pole Mount Panel Antenna
75’ LMR400 Cable
Kit 304422-40020
50 Ohm 4G Omni Antenna
20’ Wilson400 cable
Kit 304422-5810
50 Ohm 4G Omni Antenna
10’ RG58 cable
Kit 304422-1120
50 Ohm 4G Omni Antenna
20’ RG11 cable
May need separate adapter
75 Ohm Outside Antenna Kits
Kit 301111-0675
Yagi Directional Antenna
75’ RG6 Cable
N-Male to F-Female adapter
Kit 311201-0620
Omni Directional w/ F-Female
20’ RG6 Cable
Kit 314473-0640
75 Ohm Pole Mount Panel Antenna
40’ RG6 Cable
Kit 311141-0620
75 Ohm Grey Brick Antenna
20’ RG6 Cable
Kit 301111-11140
Yagi Directional Antenna
140’ RG11 Cable
N-Male to F-Female adapter
Kit 311201-1120
Omni Directional w/ F-Female
20’ RG11 Cable
Kit 314473-1175
75 Ohm Pole Mount Panel Antenna
75’ RG11 Cable
Kit 314475-0630
75 Ohm Wide Band Directional
30’ RG6 Cable
Kit 314475-1175
75 Ohm Wide Band Directional
75’ RG11 Cable
Kit 311141-1120
75 Ohm Grey Brick Antenna
20’ RG11 Cable
Kit 304421-17410
75 Ohm 4G Omni Antenna
10’ RG174 cable
Kit 304421-0610
75 Ohm 4G Omni Antenna
10’ RG6 cable
Kit 304421-5810
75 Ohm 4G Omni Antenna
10’ RG58 cable
May need separate adapter
Kit 304421-1120
75 Ohm 4G Omni Antenna
20’ RG 11 cable
Antenna Kit Options
14
IN-BUILDING SIGNAL BOOSTER WILSON PRO 1000R
EN
Product Number 460037
Model Number 460036
FCC ID
PWO460037
Connectors N-Female
Antenna Impedance 50 Ohms
Frequency
698-716 MHz, 729-746 MHz, 746-756 MHz, 777-787 MHz, 824-894 MHz, 1850-1995 MHz,
1710-1755/2110-2155 MHz
Passband Gain (nominal)
700
MHz Band12/17
57.6
700MHz Band13
58.0
800MHz
59.2
1700/2100
MHz
65.7
1900
MHz
65.2
20 dB Bandwidth (MHz)
700
MHz Band12/17 700MHz Band13 800MHz 1700/2100MHz 1900MHz
Typical
Maximum
29.6
35.4
30.3
35.4
36.8
37.8
77.5
81.0
74.5
75.1
Power output for single cell
phone (Uplink) dBm
700
MHz Band12/17 700MHz Band13 800MHz 1700MHz 1900MHz
25.3 25.8 24.7 26.2 25.3
Power output for single cell
phone (Downlink) dBm
700
MHz Band12/17 700MHz Band13 800MHz 2100MHz 1900MHz
15.2 13.9 15.4 15.4 15.4
Power output for multiple
received channels (Uplink) dBm
No. Tones
700
MHz Band12/17 700MHz Band13 800MHz 1700MHz 1900MHz
2 23.0 23.9 20.4 22.4 22.1
3 19.5 20.4 16.9 18.9 18.6
4 17.0 17.9 14.4 16.4 16.1
5 15.0 15.9 12.4 14.4 14.1
6 13.5 14.4 10.9 12.9 12.6
Power output for multiple
received channels
(Downlinklink) dBm
No. Tones 700
MHz Band12/17 700MHz Band13 800MHz 2100MHz 1900MHz
2 16.1 15.2 15.3 12.0 15.3
3 12.6 11.7 11.8 8.5 11.8
4 10.1 9.2 9.3 6.0 9.3
5 8.1 7.2 7.3 4.0 7.3
6 6.6 5.7 5.8 2.5 5.8
Noise Figure 5 dB nominal
Isolation > 90 dB
Power Requirements
12V 3A
The term “IC” before the radio certifi cation number only signifi es that Industry Canada technical specifi cations were met.
Each Signal Booster is individually tested and factory set to ensure FCC compliance. The Signal Booster cannot be
adjusted without factory reprogramming or disabling the hardware. The Signal Booster will amplify, but not alter
incoming and outgoing signals in order to increase coverage of authorized frequency bands only. If the Signal Booster
is not in use for fi ve minutes, it will reduce gain until a signal is detected. If a detected signal is too high in a frequency
band, or if the Signal Booster detects an oscillation, the Signal Booster will automatically turn the power o on that
band. For a detected oscillation the Signal Booster will automatically resume normal operation after a minimum of 1
minute. After 5 (fi ve) such automatic restarts, any problematic bands are permanently shut o until the Signal Booster
has been manually restarted by momentarily removing power from the Signal Booster. Noise power, gain, and linearity
are maintained by the Signal Booster’s microprocessor.
The Manufacturer’s rated output power of this equipment is for single carrier operation. For situations when multiple
carrier signals are present, the rating would have to be reduced by 3.5 dB, especially where the output signal is re-
radiated and can cause interference to adjacent band users. This power reduction is to be by means of input power or
gain reduction and not by an attenuator at the output of the device.
Specifi cations
15
WILSON PRO 1000R IN-BUILDING SIGNAL BOOSTER
EN
Notes
30 DAY MONEY-BACK GUARANTEE
All WilsonPro products are protected by WilsonPro 30-day money-back guarantee.
If for any reason the performance of any product is not acceptable, simply return
the product directly to the reseller with a dated proof of purchase.
3 YEAR WARRANTY
WilsonPro Boosters are warranted for three (3) years against defects in
workmanship and/or materials. Warranty cases may be resolved by returning the
product directly to the reseller with a dated proof of purchase.
Signal Boosters may also be returned directly to the manufacturer at the
consumer’s expense, with a dated proof of purchase and a Returned Material
Authorization (RMA) number supplied by WilsonPro. WilsonPro shall, at its option,
either repair or replace the product.
This warranty does not apply to any Signal Boosters determined by WilsonPro
to have been subjected to misuse, abuse, neglect, or mishandling that alters or
damages physical or electronic properties.
Replacement products may include refurbished WilsonPro products that have been
recertified to conform with product specifications.
RMA numbers may be obtained by contacting Customer Support.
DISCLAIMER: The information provided by WilsonPro is believed to be complete and
accurate. However, no responsibility is assumed by WilsonPro for any business or
personal losses arising from its use, or for any infringements of patents or other rights
of third parties that may result from its use.
NEED HELP?
support.wilsonpro.com 866.294.1660
Warranty
wilsonpro.com 866.294.1660
Guide de l’utilisateur
Amplifi cateur de signal pour bâtiment
avec technologie XDR (Plage dynamique étendue)
WILSON PRO
1000R
Une marque Wilson Electronics
FRANÇAIS
Contenu de l'ensemble
1
À propos du système WilsonPro 1000R
2
Caractéristiques clés
4
Avantages comparativement à la concurrence
5
Réglage après l’installation
7
Écran d'état
8
Écrans d'état de bande
10
Directives de sécurité
12
Garantie
15
Table des matières
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16
  • Page 17 17
  • Page 18 18
  • Page 19 19
  • Page 20 20
  • Page 21 21
  • Page 22 22
  • Page 23 23
  • Page 24 24
  • Page 25 25
  • Page 26 26
  • Page 27 27
  • Page 28 28
  • Page 29 29
  • Page 30 30
  • Page 31 31
  • Page 32 32
  • Page 33 33
  • Page 34 34
  • Page 35 35
  • Page 36 36

WilsonPro Pro 1000R Guide d'installation

Taper
Guide d'installation

dans d''autres langues