Hatco GRPWS Series Le manuel du propriétaire

Hatco
Marque
Hatco
Modèle
GRPWS Series
Taper
Le manuel du propriétaire
Glo-Ray
®
Pizza Warmer
Plaque chauffante pour pizza
GRPWS Series/Série
Installation and Operating Manual
Manuel d’installation et d’utilisation
hatcocorp.com
Register Online!
(see page 2)
S’inscrire en ligne!
(voir page 16)
Do not operate this equipment unless you
have read and understood the contents
of this manual! Failure to follow the
instructions contained in this manual
may result in serious injury or death.
This manual contains important safety
information concerning the maintenance,
use, and operation of this product. If
you’re unable to understand the contents
of this manual, please bring it to the
attention of your supervisor. Keep this
manual in a safe location for future
reference.
English = p 2
WARNING
No opere este equipo al menos que haya
leído y comprendido el contenido de este
manual! Cualquier falla en el seguimiento
de las instrucciones contenidas en
este manual puede resultar en un serio
lesión o muerte. Este manual contiene
importante información sobre seguridad
concerniente al mantenimiento, uso y
operación de este producto. Si usted
no puede entender el contenido de
este manual por favor pregunte a su
supervisor. Almacenar este manual en
una localización segura para la referencia
futura.
ADVERTENCIA
Ne pas utiliser cet équipement sans avoir
lu et compris le contenu de ce manuel ! Le
non-respect des instructions contenues
dans ce manuel peut entraîner de
graves blessures ou la mort. Ce manuel
contient des informations importantes
concernant l’entretien, l’utilisation et le
fonctionnement de ce produit. Si vous ne
comprenez pas le contenu de ce manuel,
veuillez le signaler à votre supérieur.
Conservez ce manuel dans un endroit
sûr pour pouvoir vous y référer plus tard.
Français = p 16
AVERTISSEMENT
P/N 07.04.315.00 © 2019 Hatco Corporation
Form No. GRPWSM-0719
2
English
Safety information that appears in this manual is identified by
the following signal word panels:
WARNING
WARNING indicates a hazardous situation which, if not
avoided, could result in death or serious injury.
CAUTION
CAUTION indicates a hazardous situation which, if not
avoided, could result in minor or moderate injury.
NOTICE
NOTICE is used to address practices not related to personal
injury.
INTRODUCTION
Hatco Glo-Ray
®
Pizza Warmers are perfect for holding boxed
or bagged pizza and other wrapped food product on a buffet
line or at temporary serving areas. These warmers hold
hot wrapped food product and keep it at optimum serving
temperatures without affecting quality. The thermostatically-
controlled heated base in each heat zone extends the holding
times of most wrapped food product. These units also feature
incandescent lights along with a cord and plug set.
Hatco Glo-Ray Pizza Warmers are products of extensive
research and field testing. The materials used were selected
for maximum durability, attractive appearance, and optimum
performance. Every unit is inspected and tested thoroughly
prior to shipment.
This manual provides the installation, safety, and operating
instructions for Glo-Ray Pizza Warmers. Hatco recommends all
installation, operating, and safety instructions appearing in this
manual be read prior to installation or operation of the warmer.
Important Owner Information ..............................................2
Introduction ...........................................................................2
Important Safety Information ..............................................3
Model Description ................................................................4
Model Designation ...............................................................4
Specifications .......................................................................5
Plug Configurations .............................................................5
Electrical Rating Chart — GRPWS-xxxx Models ...............5
Electrical Rating Chart — GRPWS-xxxxD Models ............5
Electrical Rating Chart — GRPWS-xxxxT Models ............. 5
Electrical Rating Chart — GRPWS-xxxxQ Models ............6
Dimensions — Box Stop with Sign Holder .......................... 6
Dimensions — GRPWS-xxxx and
GRWPS-XXXXD Models ................................................... 7
Dimensions — GRPWS-xxxxT Models ...............................8
Dimensions — GRPWS-xxxxQ Models ...............................9
Installation ...........................................................................10
General .............................................................................. 10
Operation ............................................................................. 11
General .............................................................................. 11
Maintenance ........................................................................12
General .............................................................................. 12
Daily Cleaning ...................................................................12
Replacing Display Light Bulbs ...........................................12
Troubleshooting Guide ......................................................13
Options and Accessories ..................................................14
Limited Warranty ................................................................15
Authorized Parts Distributors ...........................Back Cover
IMPORTANT OWNER INFORMATION
Record the model number, serial number, voltage, and purchase
date of the unit in the spaces below (specification label located
on the back of the unit). Please have this information available
when calling Hatco for service assistance.
Model No. ____________________________________
Serial No. _____________________________________
Voltage _______________________________________
Date of Purchase _______________________________
Register your unit!
Completing online warranty registration will prevent delay in
obtaining warranty coverage. Access the Hatco website at
www.hatcocorp.com, select the Support pull-down menu,
and click on “Warranty”.
Business
Hours: 7:00 am to 5:00 pm Monday–Friday,
Central Time (CT)
(Summer Hours — June to September:
7:00 am to 5:00 pm Monday–Thursday
7:00 am to 4:00 pm Friday)
Telephone: 800-558-0607; 414-671-6350
E-mail: [email protected]
24 Hour 7 Day Parts and Service
Assistance available in the United States
and Canada by calling 800-558-0607.
Additional information can be found by visiting our web site at
www.hatcocorp.com.
CONTENTS
Form No. GRPWSM-0719
3
English
IMPORTANT SAFETY INFORMATION
WARNING
Make sure food product has been heated to the proper
food-safe temperature before placing in unit. Failure to
heat food product properly may result in serious health
risks. This unit is for holding pre-heated food product only.
Hatco Corporation is not responsible for actual food
product serving temperature. It is the responsibility of the
user to ensure that food product is held and served at a
safe temperature.
Do not place food product directly onto hardcoat surface.
Food product must be wrapped, boxed, or on a food pan.
Make sure all operators have been instructed on the safe
and proper use of the unit.
This unit is not intended for use by children or persons
with reduced physical, sensory, or mental capabilities.
Ensure proper supervision of children and keep them
away from the unit.
This unit has no “user-serviceable” parts. If service
is required on this unit, contact an Authorized Hatco
Service Agent or contact the Hatco Service Department at
800-558-0607 or 414-671-6350.
CAUTION
BURN HAZARD: Some exterior surfaces on unit will get
hot. Use caution when touching these areas.
Locate unit at proper counter height in an area that is
convenient for use. The location should be level to prevent
unit or its contents from falling accidentally and strong
enough to support the weight of the unit and contents.
The National Sanitation Foundation (NSF) requires that
units over 36″ (914 mm) in width or weighing more than
80 lbs. (36 kg) either be sealed to or raised above the
installation surface. If unit cannot be sealed at the point
of use, 4″ (102 mm) legs are included to allow for proper
cleaning access below unit.
NOTICE
Do not lay unit on the side with the control panel. Damage
to unit could occur.
Use non-abrasive cleaners and cloths only. Abrasive
cleaners and cloths could scratch finish of unit, marring its
appearance and making it susceptible to soil accumulation.
Clean unit daily to avoid malfunctions and maintain
sanitary operation.
Do not locate unit in area with excessive air movement
around unit. Avoid areas that may be subject to active air
movements or currents (i.e., near exhaust fans/hoods, air
conditioning ducts, and exterior doors).
WARNING
ELECTRIC SHOCK HAZARD:
• Plug unit into a properly grounded electrical receptacle
of the correct voltage, size, and plug configuration. If
plug and receptacle do not match, contact a qualified
electrician to determine and install proper voltage and
size electrical receptacle.
• Turn OFF power switch, unplug power cord, and
allow unit to cool before performing any cleaning,
adjustments, or maintenance.
• Unit is not weatherproof. Locate unit indoors where
ambient air temperature is a minimum of 70°F (21°C).
• DO NOT submerge or saturate with water. Unit is not
waterproof. Do not operate if unit has been submerged
or saturated with water.
• Do not steam clean or use excessive water on unit.
• This unit is not “jet-proof” construction. Do not use
jet-clean spray to clean this unit.
• Do not pull unit by power cord.
• Discontinue use if power cord is frayed or worn.
• Do not attempt to repair or replace a damaged
power cord. The cord must be replaced by Hatco, an
Authorized Hatco Service Agent, or a person with
similar qualifications.
• Do not clean unit when it is energized or hot.
• This unit must be serviced by qualified personnel only.
Service by unqualified personnel may lead to electric
shock or burn.
• Use only Genuine Hatco Replacement Parts when
service is required. Failure to use Genuine Hatco
Replacement Parts will void all warranties and may
subject operators of the equipment to hazardous
electrical voltage, resulting in electrical shock or burn.
Genuine Hatco Replacement Parts are specified to
operate safely in the environments in which they are
used. Some aftermarket or generic replacement parts
do not have the characteristics that will allow them to
operate safely in Hatco equipment.
FIRE HAZARD: Locate unit a minimum of 1″ (25 mm) from
combustible walls and materials. If safe distances are not
maintained, discoloration or combustion could occur.
Use only light bulbs that meet or exceed National
Sanitation Foundation (NSF) standards and are specifically
designed for food holding areas. Breakage of light bulbs
not specially-coated could result in personal injury and/or
food contamination.
Read the following important safety information before using this equipment to avoid serious
injury or death and to avoid damage to equipment or property.
Form No. GRPWSM-0719
4
English
MODEL DESCRIPTION
MODEL DESIGNATION
All Models
All Hatco Glo-Ray
®
Pizza Warmers are constructed of
aluminum and stainless steel. Features include tempered
glass side panels (no glass side panels on single shelf units),
a separate POWER On/Off switch for each heat zone, a
separate TEMPERATURE CONTROL for each heat zone,
incandescent lights, feet/legs, and a cord and plug set. The
operating temperature range of each heat base is from room
temperature to approximately 185°F (85°C).
GRPWS-xxxx Models
Glo-Ray Pizza Warmers are available in widths of 24″, 36″,
and 48″ (610, 914, 1219 mm); and in depths of 18″ or 24″ (457
or 610 mm). The units are available in single, dual, triple, or
quadruple shelf models.
NOTE:Singleshelfmodelsareavailableinthe24″(610mm)
depth only.
NOTE: Refer to the OPTIONS AND ACCESSORIES section
for other display light options.
Model GRPWS-xxxx
Model GRPWS-xxxxD
Models GRPWS-xxxx and GRPWS-xxxxD
Model GRPWS-xxxxT
Model GRPWS-xxxxQ
Models GRPWS-xxxxT and GRPWS-xxxxQ
G R P W S - x x x x D
Glo-Ray
Pizza Warmer
Depth of Unit (inches)
No Character = Single Shelf
D = Dual Shelf
T = Triple Shelf
Q = Quadruple Shelf
Slanted Shelf
Width of Unit (inches)
Form No. GRPWSM-0719
5
English
Model Voltage Watts Amps Plug Configuration Shipping Weight
GRPWS-2418T 120 1440 12.0 NEMA 5-15P 98 lbs. (44 kg)
GRPWS-3618T 120/208–240 2160 12.0 NEMA L14-20P 136 lbs. (62 kg)
GRPWS-4818T 120/208–240 2880 16.0 NEMA L14-20P 175 lbs. (79 kg)
GRPWS-2424T 120 1800 15.0 NEMA 5-15P * 123 lbs. (56 kg)
GRPWS-3624T 120/208–240 2700 15.0 NEMA L14-20P 175 lbs. (79 kg)
GRPWS-4824T 120/208–240 3585 20.0 NEMA L14-30P 227 lbs. (103 kg)
Model Voltage Watts Amps Plug Configuration Shipping Weight
GRPWS-2418D 120 960 8.0 NEMA 5-15P 76 lbs. (34 kg)
GRPWS-3618D 120 1440 12.0 NEMA 5-15P 91 lbs. (41 kg)
GRPWS-4818D 120
1920
16.0 NEMA 5-20P
136 lbs. (62 kg)
120/208-240 8.0 NEMA L14-20P
GRPWS-2424D 120 1200 10.0 NEMA 5-15P 108 lbs. (49 kg)
GRPWS-3624D 120 1800 15.0 NEMA 5-15P * 136 lbs. (62 kg)
GRPWS-4824D 120/208-240 2390 10.0 NEMA L14-20P 177 lbs. (80 kg)
Model Voltage Watts Amps Plug Configuration Shipping Weight
GRPWS-2424 120 345 2.9 NEMA 5-15P 40 lbs. (18 kg)
GRPWS-3624 120 505 4.2 NEMA 5-15P 45 lbs. (20 kg)
GRPWS-4824 120 660 5.5 NEMA 5-15P 60 lbs. (27 kg)
Electrical Rating Chart — GRPWS-xxxx Models
Plug Configurations
Units are supplied from the factory with an electrical cord and
plug installed. Plugs are supplied according to the applications.
WARNING
ELECTRIC SHOCK HAZARD: Plug unit into a properly
grounded electrical receptacle of the correct voltage,
size, and plug configuration. If plug and receptacle do not
match, contact a qualified electrician to determine and
install the proper voltage and size electrical receptacle.
NOTE: Receptacle not supplied by Hatco.
NEMA 5-15P NEMA 5-20P
NEMA L14-20P
NEMA L14-30P
Plug Configurations
* NEMA 5-20P for Canada
Electrical Rating Chart — GRPWS-xxxxD Models
SPECIFICATIONS
Electrical Rating Chart — GRPWS-xxxxT Models
Form No. GRPWSM-0719
6
English
Model Box Stop/Sign Width (A)
GRPWS-24xxD
GRPWS-24xxT
GRPWS-24xxQ
22-1/4″ (565 mm)
GRPWS-36xxD
GRPWS-36xxT
GRPWS-36xxQ
34-1/4″ (870 mm)
GRPWS-48xxD
GRPWS-48xxT
GRPWS-48xxQ
46-1/4″ (1175 mm)
Model Voltage Watts Amps Plug Configuration Shipping Weight
GRPWS-2418Q 120 ‡
1920
16.0 NEMA 5-20P
119 lbs. (54 kg)
120/208–240 8.0 NEMA L14-20P
GRPWS-3618Q 120/208–240 2880 12.0 NEMA L14-20P 157 lbs. (71 kg)
GRPWS-4818Q 120/208–240 3840 16.0 NEMA L14-20P 214 lbs. (97 kg)
GRPWS-2424Q 120/208–240 2400 10.0 NEMA L14-20P 151 lbs. (69 kg)
GRPWS-3624Q 120/208–240 3600 15.0 NEMA L14-20P 214 lbs. (97 kg)
GRPWS-4824Q 120/208–240 4780 20.0 NEMA L14-20P † 277 lbs. (126 kg)
SPECIFICATIONS
‡ Not available in Canada.
† NEMA L14-30P for Canada.
Electrical Rating Chart — GRPWS-xxxxQ Models
Dimensions — Box Stop with Sign Holder
A
A
2-1/2″
(64 mm)
2-3/8″
(60 mm)
FRESH HOT PIZZA
Recommended Sign Thickness = 1/8″ (3 mm)
Box Stop w/Sign Holder
Sign
Box Stop with Sign Holder Dimensions
NOTE: Signage is not supplied by Hatco.
NOTE: The Box Stop with Sign Holder is
not available for single shelf units
(GRPWS-xxxx).
Form No. GRPWSM-0719
7
English
Model
Width
(A)
Depth
(B)
Height
(C)
†
Height
(D)
†
Footprint
Width (E)
Footprint
Depth (F)
Shelf
Height (G)
GRPWS-2424
22-7/8″
(581 mm)
24-1/4″
(616 mm)
10-3/8″
(264 mm)
6-7/8″
(174 mm)
20-1/8″
(511 mm)
21-3/8″
(543 mm)
---
---
GRPWS-3624
34-7/8″
(886 mm)
24-1/4″
(616 mm)
10-3/8″
(264 mm)
6-7/8″
(174 mm)
32-1/8″
(816 mm)
21-3/8″
(543 mm)
---
---
GRPWS-4824
46-7/8″
(1191 mm)
24-1/4″
(616 mm)
10-3/8″
(264 mm)
6-7/8″
(174 mm)
44-1/8″
(1121 mm)
21-3/8″
(543 mm)
---
---
GRPWS-2418D
23-7/8″
(606 mm)
20-1/16″
(509 mm)
22-9/16″
(573 mm)
19-1/2″
(494 mm)
20-1/8″
(511 mm)
15-3/8″
(391 mm)
4-1/8″
(104 mm)
GRPWS-3618D
35-7/8″
(911 mm)
20-1/16″
(509 mm)
22-9/16″
(573 mm)
19-1/2″
(494 mm)
32-1/8″
(816 mm)
15-3/8″
(391 mm)
4-1/8″
(104 mm)
GRPWS-4818D
47-7/8″
(1216 mm)
20-1/16″
(509 mm)
22-9/16″
(573 mm)
19-1/2″
(494 mm)
44-1/8″
(1121 mm)
15-3/8″
(391 mm)
4-1/8″
(104 mm)
GRPWS-2424D
23-7/8″
(606 mm)
26-1/16″
(662 mm)
23-5/8″
(600 mm)
19-1/2″
(494 mm)
20-1/8″
(511 mm)
21-3/8″
(543 mm)
4-1/8″
(104 mm)
GRPWS-3624D
35-7/8″
(911 mm)
26-1/16″
(662 mm)
23-5/8″
(600 mm)
19-1/2″
(494 mm)
32-1/8″
(816 mm)
21-3/8″
(543 mm)
4-1/8″
(104 mm)
GRPWS-4824D
47-7/8″
(1216 mm)
26-1/16″
(662 mm)
23-5/8″
(600 mm)
19-1/2″
(494 mm)
44-1/8″
(1121 mm)
21-3/8″
(543 mm)
4-1/8″
(104 mm)
SPECIFICATIONS
Dimensions — GRPWS-xxxx and GRPWS-xxxxD
Front View
Side View
A
B
E
F
C
D
GRPWS-xxxx Dimensions
† Height (C and D) includes 4″ (102 mm) legs. Subtract 4″
(102 mm) from Height (C and D) if unit is sealed to countertop.
Subtract 3″ (76 mm) from Height (C and D) if unit is equipped
with 1″ (25 mm) feet.
C
Rear View
Side View
F
B
E
A
G
D
GRPWS-xxxxD Dimensions
Form No. GRPWSM-0719
8
English
Model
Width
(A)
Depth
(B)
Height
(C)†
Height
(D)†
Footprint
Width (E)
Footprint
Depth (F)
Shelf
Height (G)
GRPWS-2418T
23-7/8″
(606 mm)
20-1/16″
(509 mm)
29-11/16″
(754 mm)
26-9/16″
(674 mm)
20-1/8″
(511 mm)
15-3/8″
(391 mm)
4-1/8″
(104 mm)
GRPWS-3618T
35-7/8″
(911 mm)
20-1/16″
(509 mm)
29-11/16″
(754 mm)
26-9/16″
(674 mm)
32-1/8″
(816 mm)
15-3/8″
(391 mm)
4-1/8″
(104 mm)
GRPWS-4818T
47-7/8″
(1216 mm)
20-1/16″
(509 mm)
29-11/16″
(754 mm)
26-9/16″
(674 mm)
44-1/8″
(1121 mm)
15-3/8″
(391 mm)
4-1/8″
(104 mm)
GRPWS-2424T
23-7/8″
(606 mm)
26-1/16″
(662 mm)
30-3/4″
(781 mm)
26-9/16″
(674 mm)
20-1/8″
(511 mm)
21-3/8″
(543 mm)
4-1/8″
(104 mm)
GRPWS-3624T
35-7/8″
(911 mm)
26-1/16″
(662 mm)
30-3/4″
(781 mm)
26-9/16″
(674 mm)
32-1/8″
(816 mm)
21-3/8″
(543 mm)
4-1/8″
(104 mm)
GRPWS-4824T
47-7/8″
(1216 mm)
26-1/16″
(662 mm)
30-3/4″
(781 mm)
26-9/16″
(674 mm)
44-1/8″
(1121 mm)
21-3/8″
(543 mm)
4-1/8″
(104 mm)
SPECIFICATIONS
Dimensions — GRPWS-xxxxT Models
GRPWS-xxxxT Dimensions
† Height (C and D) includes 4″ (102 mm) legs. Subtract 4″
(102 mm) from Height (C and D) if unit is sealed to countertop.
Form No. GRPWSM-0719
9
English
Model
Width
(A)
Depth
(B)
Height
(C)†
Height
(D)†
Footprint
Width (E)
Footprint
Depth (F)
Shelf
Height (G)
GRPWS-2418Q
23-7/8″
(606 mm)
20-1/16″
(509 mm)
36-13/16″
(935 mm)
33-11/16″
(855 mm)
20-1/8″
(511 mm)
15-3/8″
(391 mm)
4-1/8″
(104 mm)
GRPWS-3618Q
35-7/8″
(911 mm)
20-1/16″
(509 mm)
36-13/16″
(935 mm)
33-11/16″
(855 mm)
32-1/8″
(816 mm)
15-3/8″
(391 mm)
4-1/8″
(104 mm)
GRPWS-4818Q
47-7/8″
(1216 mm)
20-1/16″
(509 mm)
36-13/16″
(935 mm)
33-11/16″
(855 mm)
44-1/8″
(1121 mm)
15-3/8″
(391 mm)
4-1/8″
(104 mm)
GRPWS-2424Q
23-7/8″
(606 mm)
26-1/16″
(662 mm)
37-7/8″
(962 mm)
33-11/16″
(855 mm)
20-1/8″
(511 mm)
21-3/8″
(543 mm)
4-1/8″
(104 mm)
GRPWS-3624Q
35-7/8″
(911 mm)
26-1/16″
(662 mm)
37-7/8″
(962 mm)
33-11/16″
(855 mm)
32-1/8″
(816 mm)
21-3/8″
(543 mm)
4-1/8″
(104 mm)
GRPWS-4824Q
47-7/8″
(1216 mm)
26-1/16″
(662 mm)
37-7/8″
(962 mm)
33-11/16″
(855 mm)
44-1/8″
(1121 mm)
21-3/8″
(543 mm)
4-1/8″
(104 mm)
SPECIFICATIONS
GRPWS-xxxxQ Dimensions
Dimensions — GRPWS-xxxxQ Models
† Height (C and D) includes 4″ (102 mm) legs. Subtract 4″
(102 mm) from Height (C and D) if unit is sealed to countertop.
Form No. GRPWSM-0719
10
English
INSTALLATION
General
Hatco Glo-Ray
®
Pizza Warmers are shipped with most
components pre-assembled. Care should be taken when
unpacking shipping carton to avoid damage to the unit and
components enclosed.
WARNING
ELECTRIC SHOCK HAZARD: Unit is not weatherproof.
Locate unit indoors where ambient air temperature is a
minimum of 70°F (21°C).
FIRE HAZARD: Locate unit a minimum of 1″ (25 mm) from
combustible walls and materials. If safe distances are not
maintained, discoloration or combustion could occur.
CAUTION
The National Sanitation Foundation (NSF) requires that
units over 36″ (914 mm) in width or weighing more than
80 lbs. (36 kg) either be sealed to or raised above the
installation surface. If unit cannot be sealed at the point
of use, 4″ (102 mm) legs are included to allow for proper
cleaning access below unit.
1. Remove the unit from the carton. Two people are required
for this step.
NOTE: To prevent delay in obtaining warranty coverage, complete
online warranty registration. See the IMPORTANT
OWNER INFORMATION section for details.
2. Remove tape and protective packaging from all surfaces
of unit.
NOTICE
Do not lay unit on the side with the control panel. Damage
to unit could occur.
3. Install the 1″ (25 mm) metal foot studs with rubber feet or
4″ (102 mm) adjustable legs. Two people are required for
this step.
a. Carefully lay the unit on its side.
Foot
Stud
Rubber
Foot
b. Install the feet or legs.
To install the 1″ (25 mm)
rubber feet:
• Thread a foot stud into
the hole at each corner
on the bottom of the unit.
Tighten securely.
• Slip a rubber foot over
each foot stud.
To install the 4″ (102 mm) adjustable legs:
4″ Leg
Adjustable Tip
• Thread a leg into the
hole at each corner on
the bottom of the unit.
Hand-tighten the legs
until snug. Do not over-
tighten.
c. Return the unit to the upright
position.
NOTE:4″ (102 mm) legs are adjustable for leveling the unit.
Usea5/8″(16mm)open-endwrenchtomakeleveling
adjustmentsoncetheunitisplacedinfinalposition.
4. Slide each side glass panel into the upper channel, then
gently lower the panel into the lower channel.
Upper Channel
Side
Glass
Panel
Lower Channel
Side Glass Panel Installation (GRPWS-xxxxD shown)
5. Install the box stop w/sign holder on each shelf. To install:
a. Position the box stop on the shelf
b. Secure the box stop at each end using the supplied
thumbscrews.
Box Stop
w/Sign Holder
Thumbscrew
Box Stop w/Sign Holder Installation (GRPWS-xxxxT shown)
NOTE: Unit must be transported in the upright position.
6. Place the unit in the desired location.
• Locate the unit in an area where the ambient air
temperature is constant and a minimum of 70°F
(21°C). Avoid areas that may be subject to active air
movements or currents (i.e., near exhaust fans/hoods,
air conditioning ducts, and exterior doors).
• Make sure the unit is at the proper counter height in an
area convenient for use.
• Make sure the countertop is level and strong enough to
support the weight of the unit and food product.
• Make sure all the feet/legs on the bottom of the unit are
positioned securely on the countertop.
Form No. GRPWSM-0719
11
English
OPERATION
General
Use the following procedures to operate a Glo-Ray Pizza
Warmer.
WARNING
Read all safety messages in the IMPORTANT SAFETY
INFORMATION section before operating this equipment.
Do not place food product directly onto hardcoat surface.
Food product must be wrapped, boxed, or on a food pan.
Startup
1. Plug the unit into a properly grounded electrical receptacle
of the correct voltage, size, and plug configuration. See
the SPECIFICATIONS section for details.
2. Turn on the desired number of shelves, depending on the
unit. For each shelf:
a. Move the Power On/Off switch to the “On” position. The
overhead lights will turn on and the heated shelf will
energize.
NOTE:ThePowerOn/Offswitchmustbeinthe“On”position
for the corresponding heated shelf to function.
CAUTION
BURN HAZARD: Some exterior surfaces on unit will get
hot. Use caution when touching these areas.
b. Turn the Temperature Control knob to the desired
temperature setting for the heated shelf. Turning the
Temperature Control knob clockwise will increase the
temperature setting. Turning the Temperature Control
knob counterclockwise will decrease the temperature
setting.
3. Allow the unit 30 minutes to reach operating temperature
before placing preheated food product.
Shutdown
1. Move the Power On/Off switch(es) to the “Off” position.
The overhead lights and heated shelf/shelves will shut off.
GRPWS Controls (GRPWS-xxxxD control panel shown)
Form No. GRPWSM-0719
12
English
MAINTENANCE
General
Hatco Glo-Ray
®
Pizza Warmers are designed for maximum
durability and performance with minimum maintenance.
WARNING
ELECTRIC SHOCK HAZARD:
• Turn OFF power switch, unplug power cord, and
allow unit to cool before performing any cleaning,
adjustments, or maintenance.
• DO NOT submerge or saturate with water. Unit is not
waterproof. Do not operate if unit has been submerged
or saturated with water.
• Do not steam clean or use excessive water on unit.
• This unit is not “jet-proof” construction. Do not use
jet-clean spray to clean this unit.
• Do not clean unit when it is energized or hot.
• Use only Genuine Hatco Replacement Parts when
service is required. Failure to use Genuine Hatco
Replacement Parts will void all warranties and may
subject operators of the equipment to hazardous
electrical voltage, resulting in electrical shock or burn.
Genuine Hatco Replacement Parts are specified to
operate safely in the environments in which they are
used. Some aftermarket or generic replacement parts
do not have the characteristics that will allow them to
operate safely in Hatco equipment.
This unit has no “user-serviceable” parts. If service
is required on this unit, contact an Authorized Hatco
Service Agent or contact the Hatco Service Department at
800-558-0607 or 414-671-6350.
Daily Cleaning
To preserve the finish of the unit as well as maintain
performance, it is recommended that the unit be cleaned daily.
NOTICE
Use non-abrasive cleaners and cloths only. Abrasive
cleaners and cloths could scratch finish of unit, marring its
appearance and making it susceptible to soil accumulation.
Clean unit daily to avoid malfunctions and maintain
sanitary operation.
1. Turn off the unit, unplug the power cord, and allow the unit
to cool.
2. Remove the box stop w/sign holder on each shelf by
unscrewing the thumbscrews at each end of the box stop.
3. Wipe down all exterior and interior surfaces using a damp,
non-abrasive cloth. A non-abrasive cleaner may be used
for difficult stains. Hard to reach areas should be cleaned
using a small brush and mild soap.
4. Clean the side glass panels using a standard glass cleaner.
The glass panels can be removed for cleaning by reversing
the installation procedure shown in the installation section
of this manual.
5. Wipe down each box stop w/sign holder using a damp,
non-abrasive cloth, then reinstall.
Replacing Display Light Bulbs
WARNING
Use only light bulbs that meet or exceed National
Sanitation Foundation (NSF) standards and are specifically
designed for food holding areas. Breakage of light bulbs
not specially coated could result in personal injury and/or
food contamination.
The display lights are incandescent light bulbs that illuminate
the warming area. Each bulb has a special coating to guard
against injury and food contamination in the event of breakage.
1. Turn off the unit, unplug the power cord, and allow the unit
to cool.
2. Unscrew the light bulb from the unit and replace it with a
new, specially-coated incandescent light bulb.
NOTE:Hatco shatter-resistant light bulbs meet NSF
standardsforfoodholdinganddisplayareas.For120
and 120/208–240 volt applications, use Hatco P/N
02.30.265.00.
Form No. GRPWSM-0719
13
English
Symptom Probable Cause Corrective Action
Light bulb not working. Light bulb defective. Replace light bulb.
Power turned OFF. Move Power On/Off switch(es) to the On position.
Heated base or shelf not hot
enough.
Temperature Control(s) set too low. Adjust Temperature Control(s) to a higher setting.
Heating element(s) not working.
Contact an Authorized Hatco Service Agent or Hatco for
assistance.
Temperature Control(s) not working properly.
Excessive air movement around unit. Restrict or redirect air movement (i.e., air conditioning duct
or exhaust fan) away from unit.
Unit connected to incorrect power supply. Contact an Authorized Hatco Service Agent or Hatco for
assistance.
Heated base or shelf too hot. Temperature Control(s) set too high. Adjust Temperature Control(s) to a lower setting.
Temperature Control(s) not working properly.
Contact an Authorized Hatco Service Agent or Hatco for
assistance.
Unit connected to incorrect power supply.
No heat, but light works. Temperature Control(s) set too low. Adjust Temperature Control(s) to a higher setting.
Heating element(s) not working.
Contact an Authorized Hatco Service Agent or Hatco for
assistance.
Temperature Control(s) not working properly.
No heat and no lights. Power turned OFF. Move Power On/Off switch(es) to the On position.
Circuit breaker tripped. Reset circuit breaker. If circuit breaker continues to trip,
contact Authorized Service Agent or Hatco for assistance.
Power switch defective. Contact an Authorized Hatco Service Agent or Hatco for
assistance.
TROUBLESHOOTING GUIDE
WARNING
This unit must be serviced by qualified personnel only.
Service by unqualified personnel may lead to electric
shock or burn.
WARNING
ELECTRIC SHOCK HAZARD: Turn OFF power switch,
unplug power cord, and allow unit to cool before
performing any cleaning, adjustments, or maintenance.
Troubleshooting Questions?
If you continue to have problems resolving an issue, please contact the nearest Authorized Hatco Service Agency or Hatco for
assistance. To locate the nearest Service Agency, log onto the Hatco website at www.hatcocorp.com, select the Support pull-
down menu, and click on “Find A Service Agent”; or contact the Hatco Parts and Service Team at:
Telephone: 800-558-0607 or 414-671-6350
e-mail: [email protected]
Form No. GRPWSM-0719
14
English
OPTIONS AND ACCESSORIES
Digital Temperature Controller
The digital temperature controller is factory installed and takes
the place of the standard control panel. Use the following
procedure to operate the digital temperature controller.
Startup
1. Move the Power I/O (on/off) switch(es) to the I (on) position.
• The corresponding digital temperature controller will
energize and the current temperature of the shelf or
“LO” will appear on the digital display. “LO” indicates
the shelf temperature is below 70°F(21°C).
2. Press the key three times to verify the setpoint
temperature. (“SP” will be displayed after the second press.)
• The setpoint temperature will be shown for 10 seconds.
After 10 seconds, the digital display will revert to
the current temperature of the unit. To change the
setpoint temperature, refer to “Changing the Setpoint
Temperature” in this section.
NOTE:Thedigitaltemperaturecontrollerispre-settoasetpoint
temperatureof185°F(85°C)atthefactory.Oncethe
setpoint temperature is changed, the new setpoint
temperature will remain in memory until it is changed
again. The minimum to maximum setpoint temperature
rangeis70°F(21°C)to200°F(93°C).
CAUTION
BURN HAZARD: Some exterior surfaces on unit will get
hot. Use caution when touching these areas.
3. Allow unit 15–20 minutes to reach operating temperature.
Shutdown
1. Move the Power I/O (on/off) switch to the O (off) position.
The digital temperature controller and heating elements
will shut off.
Changing the Setpoint Temperature
Use the following procedure to change the setpoint temperature.
1. Press the key three times. The current setpoint
temperature will be shown on the digital display (“SP” will
be displayed after the second press).
2. Press the key or key within 10 seconds to change
the setpoint temperature.
3. Press the key to lock in the new setpoint temperature.
The digital display will go blank for two seconds to show
that the new setting has been accepted.
NOTE: After10secondsofinactivityduringtheprogramming
process, the controller will exit programming mode
automatically without saving any changes.
Changing Fahrenheit and Celsius Setting
Use the following procedure to change between Fahrenheit
and Celsius on the display.
1. Press the key once. Either an “F” for Fahrenheit or “C”
for Celsius will be displayed.
2. Press the key or key within 10 seconds to change
between “F” (Fahrenheit) and “C” (Celsius).
3. Press the key three times to lock in the new setting.
The digital display will go blank for two seconds to show
that the new setting has been accepted.
NOTE: After10secondsofinactivityduringtheprogramming
process, the controller will exit programming mode
automatically without saving any changes.
Digital
Temperature
Controller
Power I/O (on/off)
Switch
Control Panel with Digital Temperature Controler
Halogen Display Light Bulbs
Shatter-resistant halogen display light bulbs
can be ordered in place of the standard
incandescent display light bulbs. The bulbs
have a special coating to guard against
injury and food contamination in the event
of breakage. For 120 and 120/208–240 volt
applications, use Hatco P/N 02.30.081.00.
Form No. GRPWSM-0719
15
English
1. PRODUCT WARRANTY
Hatco warrants the products that it manufactures (the “Products”)
to be free from defects in materials and workmanship, under
normal use and service, for a period of one (1) year from the
date of purchase when installed and maintained in accordance
with Hatco’s written instructions or 18 months from the date
of shipment from Hatco. Buyer must establish the Product’s
purchase date by registering the Product with Hatco or by other
means satisfactory to Hatco in its sole discretion.
Hatco warrants the following Product components to be free
from defects in materials and workmanship from the date of
purchase (subject to the foregoing conditions) for the period(s)
of time and on the conditions listed below:
a) One (1) Year Parts and Labor PLUS One (1) Additional
Year Parts-Only Warranty:
Conveyor Toaster Elements (metal sheathed)
Drawer Warmer Elements (metal sheathed)
Drawer Warmer Drawer Rollers and Slides
Strip Heater Elements (metal sheathed)
Display Warmer Elements (metal sheathed air heating)
Holding Cabinet Elements (metal sheathed air heating)
Heated Well Elements — HW and HWB Series
(metal sheathed)
b) Two (2) Year Parts and Labor Warranty:
Induction Ranges
Induction Warmers
c) One (1) Year Parts and Labor PLUS Four (4) Years
Parts-Only Warranty:
3CS and FR Tanks
d) One (1) Year Parts and Labor PLUS Nine (9) Years
Parts-Only Warranty on:
Electric Booster Heater Tanks
Gas Booster Heater Tanks
e) Ninety (90) Day Parts-Only Warranty:
Replacement Parts
THE FOREGOING WARRANTIES ARE EXCLUSIVE AND
IN LIEU OF ANY OTHER WARRANTY, EXPRESSED OR
IMPLIED, INCLUDING BUT NOT LIMITED TO ANY IMPLIED
WARRANTY OF MERCHANTABILITY OR FITNESS FOR
A PARTICULAR PURPOSE OR PATENT OR OTHER
INTELLECTUAL PROPERTY RIGHT INFRINGEMENT. Without
limiting the generality of the foregoing, SUCH WARRANTIES
DO NOT COVER: Coated incandescent light bulbs, fluorescent
lights, heat lamp bulbs, coated halogen light bulbs, halogen
heat lamp bulbs, xenon light bulbs, LED light tubes, glass
components, and fuses; Product failure in booster tank, fin
tube heat exchanger, or other water heating equipment caused
by liming, sediment buildup, chemical attack, or freezing;
or Product misuse, tampering or misapplication, improper
installation, or application of improper voltage.
2. LIMITATION OF REMEDIES AND DAMAGES
Hatco’s liability and Buyer’s exclusive remedy hereunder will
be limited solely, at Hatco’s option, to repair or replacement
using new or refurbished parts or Product by Hatco or a Hatco-
authorized service agency (other than where Buyer is located
outside of the United States, Canada, United Kingdom, or
Australia, in which case Hatco’s liability and Buyer’s exclusive
remedy hereunder will be limited solely to replacement of part
under warranty) with respect to any claim made within the
applicable warranty period referred to above. Hatco reserves
the right to accept or reject any such claim in whole or in part. In
the context of this Limited Warranty, “refurbished” means a part
or Product that has been returned to its original specifications
by Hatco or a Hatco-authorized service agency. Hatco will not
accept the return of any Product without prior written approval
from Hatco, and all such approved returns shall be made
at Buyer’s sole expense. HATCO WILL NOT BE LIABLE,
UNDER ANY CIRCUMSTANCES, FOR CONSEQUENTIAL
OR INCIDENTAL DAMAGES, INCLUDING BUT NOT LIMITED
TO LABOR COSTS OR LOST PROFITS RESULTING FROM
THE USE OF OR INABILITY TO USE THE PRODUCTS OR
FROM THE PRODUCTS BEING INCORPORATED IN OR
BECOMING A COMPONENT OF ANY OTHER PRODUCT OR
GOODS.
LIMITED WARRANTY
Formulaire n° GRPWSM-0719
16
Français
Les consignes de sécurité qui apparaissent dans ce manuel
sont identifiées par les mots indicateurs suivants :
AVERTISSEMENT
AVERTISSEMENT indique une situation dangereuse qui,
si elle n’est pas évitée, peut provoquer la mort ou des
blessures graves.
ATTENTION
ATTENTION indique une situation dangereuse qui, si elle
n’est pas évitée, peut provoquer des blessures légères ou
moyennes.
AVIS
AVIS est utilisé pour des questions sans rapport avec des
blessures corporelles.
INTRODUCTION
Les plaques chauffantes pour pizza Hatco Glo-Ray
®
sont
parfaites pour présenter des pizzas emballées dans des boîtes
ou des sacs ainsi que d’autres produits alimentaires emballés
sur un buffet ou dans un espace de service temporaire. Ces
appareils chauffants maintiendront vos aliments chauds
emballés à des températures optimales ; ils seront prêts à être
servis à tout moment sans que la qualité ne soit altérée. Elles
comportent une base chauffante contrôlée par un thermostat
pour chaque zone de chauffe afin de prolonger les temps de
conservation de la plupart des plats. Ces appareils disposent
également de lampes à incandescence et d’un cordon avec fiche
électrique.
Les chauffe-pizzas Glo-Ray de Hatco sont le fruit de recherches
poussées et d’essais sur site complets. Les matériaux utilisés
ont été sélectionnés pour une durabilité maximale, une
esthétique et des performances optimales. Chaque appareil
est minutieusement inspecté et testé avant expédition.
Ce manuel fournit les instructions d’installation et d’utilisation
des chauffe-pizzas Glo-Ray, et les consignes de sécurité
associées. Hatco vous recommande de lire l’ensemble des
instructions d’installation, de sécurité et de fonctionnement
contenues dans ce manuel avant d’installer et d’utiliser l’appareil.
Informations Importantes pour le Propriétaire ................16
Introduction .........................................................................16
Consignes de Sécurité Importantes ................................. 17
Description du Modèle .......................................................18
Désignation du Modèle ...................................................... 18
Caractéristiques Techniques ............................................19
Configuration des Fiches ...................................................19
Tableau des valeurs nominales électriques ......................19
Dimensions — Butoir avec porte-étiquettes ...................... 20
Dimensions ........................................................................ 21
Installation ...........................................................................24
Généralités ........................................................................24
Mode d’emploi ....................................................................25
Généralités ........................................................................25
Maintenance ........................................................................26
Généralités ........................................................................26
Nettoyage quotidien ...........................................................26
Remplacement des ampoules de la vitrine .......................26
Guide de Dépannage ..........................................................27
Options et accessoires ...................................................... 28
Garantie Limitée .................................................................29
Autorisés Distributeurs de Pièces ........Couverture Arrière
INFORMATIONS IMPORTANTES POUR LE PROPRIÉTAIRE
Notez le numéro de modèle, le numéro de série, la tension
et la date d’achat de l’appareil dans les espaces ci-dessous
(étiquette des caractéristiques techniques située au dos de
l’appareil). Veuillez avoir cette information à portée de la main
si vous appelez Hatco pour assistance.
Modèle No. ______________________________________
Numéro de série __________________________________
Voltage _________________________________________
Date d’achat _____________________________________
Enregistrez votre appareil!
Remplissez la garantie en ligne pour éviter les retards
pour faire jouer la garantie. Accédez au site Web Hatco
www.hatcocorp.com, sélectionnez le menu déroulant
Support (Assistance), puis cliquez sur « Warranty » (Garantie).
Horaires
ouvrables : 7h00 à 17h00 du lundi au vendredi
Heure du Centre (CT)
(Horaires d’été—juin à septembre:
7h00 à 17h00 du lundi au jeudi
7h00 à 16h00 le vendredi)
Téléphone: 800-558-0607; 414-671-6350
Courriel: [email protected]
Service d'assistance et de pièces de
rechange disponible 7j/7, 24h/24 aux
États-Unis et au Canada en composant
le 800-558-0607.
Des renseignements supplémentaires sont disponibles sur
notre site Web à www.hatcocorp.com.
SOMMAIRE
Formulaire n° GRPWSM-0719
17
Français
CONSIGNES DE SÉCURITÉ IMPORTANTES
AVERTISSEMENT
S’assurer que la nourriture a été chauffée à une
température adaptée à une alimentation saine avant de
la placer sur l’appareil. Le non-chauffage des aliments à
une température appropriée peut poser un grand risque
pour la santé. Cet appareil n’est destiné qu’à maintenir des
aliments préchauffés au chaud.
Hatco Corporation n’est pas responsable de la température
réelle à laquelle les aliments sont servis. Il est de la
responsabilité de l’utilisateur de s’assurer que les produits
alimentaires sont maintenus et servis à une température
sans danger.
Ne placez aucun produit alimentaire directement sur
une surface à revêtement dur. Les produits alimentaires
doivent être emballés, placés dans une boîte ou dans un
bac alimentaire.
Assurez-vous que tous les opérateurs ont été formés à
l’utilisation sûre et correcte de l’appareil.
Cet appareil ne doit pas être utilisé par des enfants ou des
personnes avec des capacités physiques, sensorielles ou
mentales diminuées. Assurez-vous que les enfants sont
bien surveillés et tenez-les à l’écart de l’appareil.
Cet appareil ne contient aucune pièce réparable par
l’utilisateur. Si cet appareil doit être réparé, contacter un
réparateur Hatco agréé ou le Service après-vente Hatco au
800-558-0607 ou 414-671-6350.
ATTENTION
DANGER DE BRÛLURE : Certaines surfaces extérieures
de l’appareil deviennent chaudes. Toucher ces zones de
l’appareil avec précaution.
Placez l’unité à une hauteur adaptée au comptoir, à un
emplacement pratique à utiliser. L’emplacement doit être
plan pour éviter que l’unité ou son contenu ne tombe
accidentellement, et suffisamment solide pour supporter
le poids de l’unité et de son contenu.
La National Sanitation Foundation (NSF) exige que les
appareils de plus de 914 mm (36″) de large ou pesant plus
de 36 kg (80 lbs.) soient fixés sur ou surélevés par rapport à
la surface d’installation. Si l’appareil ne peut pas être fixé sur
l’emplacement d’utilisation, des pieds de 102 mm (4″) sont
fournis pour permettre le nettoyage en dessous de l’appareil.
AVIS
Ne couchez pas l’unité sur le côté comportant le panneau
de commande. L’unité pourrait être endommagée.
Utilisez seulement des nettoyants non abrasifs et des
chiffons doux. Les chiffons et nettoyant abrasifs pourraient
érafler la finition de l’unité, entachant son apparence et la
rendant susceptible à l’accumulation de saleté.
Nettoyez l’unité quotidiennement pour éviter les
dysfonctionnements et assurer un fonctionnement sain.
Ne placez pas l’appareil dans un endroit où la circulation
de l’air est trop forte. Évitez les zones pouvant être
soumises à des mouvements d’air ou à des courants d’air
actifs (comme à proximité de ventilateurs d’échappement/
de hottes d’aspiration, de conduites de climatisation et de
portes extérieures).
AVERTISSEMENT
DANGER DE DÉCHARGE ÉLECTRIQUE :
• Brancher l’appareil sur une prise de courant avec terre
de tension, de format et de configuration des broches
corrects. Si la fiche et la prise ne se correspondent pas,
s’adresser à un électricien qualifié pour déterminer et
installer une prise de courant de format et de tension
corrects.
• Mettez l’unité hors tension depuis l’interrupteur,
débranchez le cordon d’alimentation et laissez l’unité
refroidir avant d’effectuer tout nettoyage, tout réglage
ou tout entretien.
• NE PAS immerger l’appareil ni le saturer d’eau.
L’appareil n’est pas étanche à l’eau. Ne pas le faire
fonctionner s’il a été immergé ou saturé d’eau.
• Ne pas nettoyer à la vapeur ni utiliser trop d’eau sur
l’appareil.
• Cet appareil n’est pas étanche aux jets. Ne pas utiliser
de jet sous pression pour nettoyer l’appareil.
• L’appareil n’est pas à l’épreuve des intempéries. Placer
l’appareil à l’intérieur à une température ambiante de
21°C (70°F) minimum.
• Ne pas utiliser l’appareil si le cordon est endommagé
ou usé.
• Ne pas tirer l’appareil par son cordon électrique.
• Ne pas tenter de réparer ni de changer un cordon
électrique endommagé. Ce cordon doit être changé
par Hatco, par un réparateur Hatco agréé ou par une
personnes de qualifications comparables.
• Ne nettoyez pas l’appareil tant qu’il est branché ou
chaud.
• Cette unité doit être entretenue uniquement par des
personnes qualifiées. Un entretien réalisé par des
personnes non-qualifiées peut entraîner des décharges
électriques ou provoquer des brûlures.
• Utilisez uniquement des pièces de rechange d’origine
Hatco lorsque l’entretien est nécessaire. Utilisez des
pièces détachées Hatco authentiques sous peine
d’annuler toutes les garanties et d’exposer l’utilisateur
à des tensions électriques dangereuses pouvant
entraîner une électrocution ou des brûlures. Les pièces
de rechange authentiques Hatco sont spécifiées pour
fonctionner en toute sécurité dans les environnements
dans lesquels elles sont utilisées. Certaines pièces de
rechange génériques ou d’après-vente n’ont pas les
caractéristiques qui leur permettent d’opérer en toute
sécurité dans les équipements Hatco.
DANGER D’INCENDIE : Placez l’unité à au moins 25 mm
(1″) de murs ou de matières inflammables. Si ces distances
de sécurité ne sont pas respectées, une décoloration ou
une combustion peut se produire.
N’utilisez que des ampoules électriques qui correspondent
ou qui sont supérieures aux normes de la Fondation
Nationale des Affaires Sanitaires (NSF) et qui sont
spécifiquement conçues pour les espaces de conservation
des aliments. Les bris d’une ampoule non équipée d’un
revêtement adapté peuvent provoquer des dommages
corporels et/ou une contamination des aliments.
Lisez les consignes de sécurité importantes suivantes avant d’utiliser cet équipement pour éviter
toute blessure grave ou la mort et pour éviter d’endommager l’équipement ou la propriété.
Formulaire n° GRPWSM-0719
18
Français
DESCRIPTION DU MODÈLE
DÉSIGNATION DU MODÈLE
Tous les modèles
Toutes les plaques chauffantes pour pizza Hatco Glo-Ray
®
sont
fabriquées en aluminium et acier inoxydable. Elles comportent
des panneaux latéraux en verre trempé (sauf sur les modèles
à un seul rayonnage), un interrupteur séparé pour l’alimentation
de chaque zone de chauffe, une commande de la température
pour chaque zone de chauffe, un éclairage à incandescence,
des pieds/supports et un jeu de cordon et fiche électriques. La
plage de température de service de chaque base chauffante est
comprise entre la température ambiante et environ 85°C (185°F).
Modèles GRPWS-xxxx
Les plaques chauffantes pour pizza Glo-Ray sont disponibles
en 610 mm, 914 mm et 1 219 mm de largeur (24″, 36″ et 48″)
et 457 ou 610 mm de profondeur (18″ ou 24″). Les appareils se
déclinent en modèles à un, deux, trois ou quatre rayonnages.
NOTA: Les modèles à un rayonnage sont uniquement
disponiblesen610mm(24″)deprofondeur.
NOTA:Reportez-vous à la rubrique OPTIONS ET
ACCESSOIRES pour en savoir plus sur toutes les
options disponibles en matière d’éclairage.
Modèle GRPWS-xxxx
Modèle GRPWS-xxxxD
Modèles GRPWS-xxxx and GRPWS-xxxxD
Modèle GRPWS-xxxxT
Modèle GRPWS-xxxxQ
Modèles GRPWS-xxxxT and GRPWS-xxxxQ
G R P W S - x x x x D
Glo-Ray
Plaque chauffante pour pizza
Profondeur de l'appareil (mm)
Aucune lettre = Rayonnage simple
D = Rayonnage double
T = Rayonnage triple
Q = Rayonnage quadruple
Plateau incliné
Largeur (en pouces)
Formulaire n° GRPWSM-0719
19
Français
Modèle Tension Puissance Intensité Configuration de Fiches
Poids
d’embarquement
GRPWS-2418D 120 V 960 W 8.0 A NEMA 5-15P 34 kg (76 lbs.)
GRPWS-3618D 120 V 1440 W 12.0 A NEMA 5-15P 41 kg (91 lbs.)
GRPWS-4818D 120 V
1920 W
16.0 A NEMA 5-20P
62 kg (136 lbs.)
120/208-240 V 8.0 A NEMA L14-20P
GRPWS-2424D 120 V 1200 W 10.0 A NEMA 5-15P 49 kg (108 lbs.)
GRPWS-3624D 120 V 1800 W 15.0 A NEMA 5-15P * 62 kg (136 lbs.)
GRPWS-4824D 120/208-240 V 2390 W 10.0 A NEMA L14-20P 80 kg (177 lbs.)
Modèle Tension Puissance Intensité Configuration de Fiches
Poids
d’embarquement
GRPWS-2424 120 V 345 W 2.9 A NEMA 5-15P 18 kg (40 lbs.)
GRPWS-3624 120 V 505 W 4.2 A NEMA 5-15P 20 kg (45 lbs.)
GRPWS-4824 120 V 660 W 5.5 A NEMA 5-15P 27 kg (60 lbs.)
CARACTÉRISTIQUES TECHNIQUES
Configuration des fiches
Les appareils sont livrés avec un cordon électrique avec fiche.
Différentes fiches sont fournies selon les applications.
AVERTISSEMENT
DANGER DE DÉCHARGE ÉLECTRIQUE : Brancher
l’appareil sur une prise de courant avec terre de tension,
de format et de configuration des broches corrects. Si la
fiche et la prise ne se correspondent pas, s’adresser à un
électricien qualifié pour déterminer et installer une prise
de courant de format et de tension corrects.
NOTA: PrisenonfournieparHatco.
NEMA 5-15P NEMA 5-20P
NEMA L14-20P
NEMA L14-30P
Configuration des fiches
* NEMA 5-20P pour le Canada.
Modèle Tension Puissance Intensité Configuration de Fiches
Poids
d’embarquement
GRPWS-2418T 120 V 1440 W 12.0 A NEMA 5-15P 44 kg (98 lbs.)
GRPWS-3618T 120/208–240 V 2160 W 12.0 A NEMA L14-20P 62 kg (136 lbs.)
GRPWS-4818T 120/208–240 V 2880 W 16.0 A NEMA L14-20P 79 kg (175 lbs.)
GRPWS-2424T 120 V 1800 W 15.0 A NEMA 5-15P * 56 kg (123 lbs.)
GRPWS-3624T 120/208–240 V 2700 W 15.0 A NEMA L14-20P 79 kg (175 lbs.)
GRPWS-4824T 120/208–240 V 3585 W 20.0 A NEMA L14-30P 103 kg (227 lbs.)
Tableau des valeurs nominales électriques — GRPWS-xxxx Modèles
Tableau des valeurs nominales électriques — GRPWS-xxxxD Modèles
Tableau des valeurs nominales électriques — GRPWS-xxxxT Modèles
Formulaire n° GRPWSM-0719
20
Français
Modèle Tension Puissance Intensité Configuration de Fiches
Poids
d’embarquement
GRPWS-2418Q 120 V‡
1920 W
16.0 A NEMA 5-20P
54 kg (119 lbs.)
120/208–240 V 8.0 A NEMA L14-20P
GRPWS-3618Q 120/208–240 V 2880 W 12.0 A NEMA L14-20P 71 kg (157 lbs.)
GRPWS-4818Q 120/208–240 V 3840 W 16.0 A NEMA L14-20P 97 kg (214 lbs.)
GRPWS-2424Q 120/208–240 V 2400 W 10.0 A NEMA L14-20P 69 kg (151 lbs.)
GRPWS-3624Q 120/208–240 V 3600 W 15.0 A NEMA L14-20P 97 kg (214 lbs.)
GRPWS-4824Q 120/208–240 V 4780 W 20.0 A NEMA L14-20P † 126 kg (277 lbs.)
Modèle
Butoir/Largeur
porte-étiquettes (A)
GRPWS-24xxD
GRPWS-24xxT
GRPWS-24xxQ
565 mm (22-1/4″)
GRPWS-36xxD
GRPWS-36xxT
GRPWS-36xxQ
870 mm (34-1/4″)
GRPWS-48xxD
GRPWS-48xxT
GRPWS-48xxQ
1175 mm (46-1/4″)
CARACTÉRISTIQUES TECHNIQUES
† NEMA L14-30P pour le Canada.
‡ Non disponible au Canada.
Tableau des valeurs nominales électriques — GRPWS-xxxxQ Modèles
Dimensions — Butoir avec porte-étiquettes
A
A
64 mm
(2-1/2″)
60 mm
(2-3/8″)
FRESH HOT PIZZA
Épaisseur d'étiquette recommandée = 3 mm (1/8″)
Butoir avec porte-étiquettes
Étiquette
Dimensions du butoir avec porte-étiquettes
NOTA: La signalisation n’est pas fournie par Hatco.
NOTA: Le butoir avec porte-étiquettes n’est pas
disponible pour les modèles à un seul
rayonnage(GRPWS-xxxx).
La page est en cours de chargement...
La page est en cours de chargement...
La page est en cours de chargement...
La page est en cours de chargement...
La page est en cours de chargement...
La page est en cours de chargement...
La page est en cours de chargement...
La page est en cours de chargement...
La page est en cours de chargement...
La page est en cours de chargement...
La page est en cours de chargement...
La page est en cours de chargement...
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16
  • Page 17 17
  • Page 18 18
  • Page 19 19
  • Page 20 20
  • Page 21 21
  • Page 22 22
  • Page 23 23
  • Page 24 24
  • Page 25 25
  • Page 26 26
  • Page 27 27
  • Page 28 28
  • Page 29 29
  • Page 30 30
  • Page 31 31
  • Page 32 32

Hatco GRPWS Series Le manuel du propriétaire

Hatco
Marque
Hatco
Modèle
GRPWS Series
Taper
Le manuel du propriétaire
Télécharger le PDF
rapport

dans d''autres langues

Documents connexes

Autres documents