Hatco GRSDH, GRSDS, GRSDS/H Series Le manuel du propriétaire

Hatco
Marque
Hatco
Modèle
GRSDH, GRSDS, GRSDS/H Series
Taper
Le manuel du propriétaire
P/N 07.04.301.00 © 2019 Hatco Corporation
Glo-Ray
®
Merchandising Display Warmers
Présentoirs Chauffants
GRSDH, GRSDS, and GRSDS/H Series
Installation and Operating Manual
Manuel d’installation et d’utilisation
hatcocorp.com
Register Online!
(see page 2)
S’inscrire en ligne!
(voir page 18)
Do not operate this equipment unless you
have read and understood the contents
of this manual! Failure to follow the
instructions contained in this manual
may result in serious injury or death.
This manual contains important safety
information concerning the maintenance,
use, and operation of this product. If
you’re unable to understand the contents
of this manual, please bring it to the
attention of your supervisor. Keep this
manual in a safe location for future
reference.
English = p 2
WARNING
No opere este equipo al menos que haya
leído y comprendido el contenido de este
manual! Cualquier falla en el seguimiento
de las instrucciones contenidas en
este manual puede resultar en un serio
lesión o muerte. Este manual contiene
importante información sobre seguridad
concerniente al mantenimiento, uso y
operación de este producto. Si usted
no puede entender el contenido de
este manual por favor pregunte a su
supervisor. Almacenar este manual en
una localización segura para la referencia
futura.
ADVERTENCIA
Ne pas utiliser cet équipement sans avoir
lu et compris le contenu de ce manuel ! Le
non-respect des instructions contenues
dans ce manuel peut entraîner de
graves blessures ou la mort. Ce manuel
contient des informations importantes
concernant l’entretien, l’utilisation et le
fonctionnement de ce produit. Si vous ne
comprenez pas le contenu de ce manuel,
veuillez le signaler à votre supérieur.
Conservez ce manuel dans un endroit
sûr pour pouvoir vous y référer plus tard.
Français = p 18
AVERTISSEMENT
Form No. GRSDM-1219
2
English
CONTENTS
Safety information that appears in this manual is identified by
the following signal word panels:
WARNING
WARNING indicates a hazardous situation which, if not
avoided, could result in death or serious injury.
CAUTION
CAUTION indicates a hazardous situation which, if not
avoided, could result in minor or moderate injury.
NOTICE
NOTICE is used to address practices not related to personal
injury.
INTRODUCTION
The Hatco Glo-Ray
®
Merchandising Display Warmers are
perfect for holding wrapped sandwiches or boxed pizza on
a buffet line or at temporary serving areas. These warmers
hold hot wrapped products and keep them at optimum serving
temperatures without affecting quality. Pre-focused infrared
heat from above and a thermostatically controlled heated
base extends the holding times of most wrapped food. The
infrared heating elements are guaranteed against burnout and
breakage for two years. These units also feature incandescent
lights along with a cord and plug set(s).
Hatco Glo-Ray Merchandising Display Warmers are products
of extensive research and field testing. The materials used
were selected for maximum durability, attractive appearance,
and optimum performance. Every unit is inspected and tested
thoroughly prior to shipment.
This manual provides the installation, safety, and operating
instructions for Glo-Ray Merchandising Display Warmers.
Hatco recommends all installation, operating, and safety
instructions appearing in this manual be read prior to installation
or operation of the warmer.
Important Owner Information ..............................................2
Introduction ...........................................................................2
Important Safety Information ..............................................3
Model Description ................................................................4
All Models ............................................................................ 4
GRSDH Models ................................................................... 4
GRSDS Models ...................................................................4
GRSDS/H Models ................................................................4
Model Designation ...............................................................4
Specifications .......................................................................5
Plug Configurations .............................................................5
Electrical Rating Charts ....................................................... 5
Dimensions .......................................................................... 8
Installation ........................................................................... 11
General .............................................................................. 11
Operation .............................................................................12
General .............................................................................. 12
Maintenance ........................................................................13
General .............................................................................. 13
Daily Cleaning ...................................................................13
Replacing Display Light Bulbs ...........................................13
Troubleshooting Guide ......................................................14
Options and Accessories ..................................................15
Limited Warranty ................................................................17
Authorized Parts Distributors ...........................Back Cover
IMPORTANT OWNER INFORMATION
Record the model number, serial number, voltage, and purchase
date of the unit in the spaces below (specification label located
on the back of the unit). Please have this information available
when calling Hatco for service assistance.
Model No. ________________________________________
Serial No. _________________________________________
Voltage ___________________________________________
Date of Purchase ___________________________________
Register your unit!
Completing online warranty registration will prevent delay in
obtaining warranty coverage. Access the Hatco website at
www.hatcocorp.com, select the Support pull-down menu,
and click on “Warranty”.
Business
Hours: 7:00  to 5:00  Monday–Friday,
Central Time (CT)
(Summer Hours: June to September—
7:00  to 5:00  Monday–Thursday
7:00  to 4:00  Friday)
Telephone: 800-558-0607; 414-671-6350
E-mail: [email protected]
24 Hour 7 Day Parts and Service
Assistance available in the United States
and Canada by calling 800-558-0607.
Additional information can be found by visiting our web site at
www.hatcocorp.com.
Form No. GRSDM-1219
3
English
IMPORTANT SAFETY INFORMATION
WARNING
Use only light bulbs that meet or exceed National
Sanitation Foundation (NSF) standards and are specifically
designed for food holding areas. Breakage of light bulbs
not specially coated could result in personal injury and/or
food contamination.
Do not place food product directly onto hardcoat surface.
Food product must be wrapped, boxed, or on a food pan.
Make sure all operators have been instructed on the safe
and proper use of the unit.
This unit is not intended for use by children or persons
with reduced physical, sensory, or mental capabilities.
Ensure proper supervision of children and keep them
away from the unit.
CAUTION
BURN HAZARD: Some exterior surfaces on unit will get
hot. Use caution when touching these areas.
Locate unit at proper counter height in an area that is
convenient for use. Location should be level to prevent
unit or its contents from falling accidentally and strong
enough to support the weight of the unit and contents.
The National Sanitation Foundation (NSF) requires that
units over 36″ (914 mm) in width or weighing more than
80 lbs. (36 kg) either be sealed to or raised above the
installation surface. If unit cannot be sealed at the point
of use, 4″ (102 mm) legs are included to allow for proper
cleaning access below unit.
NOTICE
Do not lay unit on the side with the control panel. Damage
to unit could occur.
Units with two power cords must each be plugged into
individual branch circuits.
Use non-abrasive cleaners and cloths only. Abrasive
cleaners and cloths could scratch finish of unit, marring
its appearance and making it susceptible to soil
accumulation. Use of abrasive materials will void warranty.
Do not slide pans across hardcoat surface, use rough-
bottomed pans, or drop anything on hardcoat surface.
Scratching may occur. Damage to hardcoat surface
caused by misuse is not covered under warranty.
IMPORTANT—DO NOT use paper towel or glass cleaner
to clean plastic surfaces such as sneeze guards and
flip-up doors. Paper towel and glass cleaner may scratch
the material. Wipe off plastic surfaces using a soft, clean,
water-dampened cloth.
Clean unit daily to avoid malfunctions and maintain
sanitary operation.
Locate the unit in an area where the ambient air
temperature is constant and a minimum of 70°F (21°C).
Avoid areas that may be subject to active air movements
or currents (i.e., near exhaust fans/hoods, air conditioning
ducts, and exterior doors).
WARNING
ELECTRIC SHOCK HAZARD:
• Plug unit into a properly grounded electrical receptacle
of the correct voltage, size, and plug configuration. If
plug and receptacle do not match, contact a qualified
electrician to determine and install proper voltage and
size electrical receptacle.
• Turn OFF power switch, unplug power cord, and allow
unit to cool before performing any cleaning, setup, or
maintenance.
• Units with two power cords must have both power
supply cords disconnected before performing any
cleaning, adjustments, or maintenance.
• Unit is not weatherproof. Locate unit indoors where
ambient air temperature is a minimum of 70°F (21°C).
• DO NOT submerge or saturate with water. Unit is not
waterproof. Do not operate if unit has been submerged
or saturated with water.
• Do not steam clean or use excessive water on unit.
• This unit is not “jet-proof” construction. Do not use
jet-clean spray to clean this unit.
• Do not clean unit when it is energized or hot.
• Do not pull unit by power cord.
• Discontinue use if power cord is frayed or worn.
• Do not attempt to repair or replace a damaged power cord.
Cord must be replaced by Hatco, an Authorized Hatco
Service Agent, or a person with similar qualifications.
• This unit must be serviced by qualified personnel only.
Service by unqualified personnel may lead to electric
shock or burn.
• Use only Genuine Hatco Replacement Parts when
service is required. Failure to use Genuine Hatco
Replacement Parts will void all warranties and may
subject operators of the equipment to hazardous
electrical voltage, resulting in electrical shock or burn.
Genuine Hatco Replacement Parts are specified to
operate safely in the environments in which they are
used. Some aftermarket or generic replacement parts
do not have the characteristics that will allow them to
operate safely in Hatco equipment.
FIRE HAZARD: Locate unit a minimum of 1″ (25 mm) from
combustible walls and materials. If safe distances are not
maintained, discoloration or combustion could occur.
Make sure food product has been heated to the proper
food-safe temperature before placing in unit. Failure to
heat food product properly may result in serious health
risks. This unit is for holding pre-heated food product only.
This unit has no “user-serviceable” parts. If service
is required on this unit, contact an Authorized Hatco
Service Agent or contact the Hatco Service Department at
800-558-0607 or 414-671-6350.
Read the following important safety information before using this equipment to avoid serious
injury or death and to avoid damage to equipment or property.
Form No. GRSDM-1219
4
English
MODEL DESCRIPTION
MODEL DESIGNATION
All Models
All Hatco Glo-Ray
®
Merchandising Display Warmers are
constructed of aluminum, stainless steel, and powdercoated
steel. Features include tempered glass side panels, a
temperature controlled heated base shelf, infrared upper
heating elements, incandescent lights, product divider rods,
legs, and a cord and plug set. The operating temperature
range is from room temperature to approximately 185°–200°F
(85°–93°C).
GRSDH Models
The GRSDH models are horizontal shelf warmers designed
to hold hot wrapped product. They can be ordered in various

single or dual shelf models.
GRSDH Model — Single Shelf
GRSDS Models
The GRSDS models are slant shelf warmers designed to
hold hot wrapped product. The shelves are slanted for the
convenience of self-serve. They can be ordered in various


units are available in triple shelf models.
GRSDS Model — Dual Shelf
GRSDS/H Models
The GRSDS/H models are dual shelf units that include one
slanted base shelf and one horizontal shelf. They can be
           
(1041 mm). Optional high wattage is available for top shelf.
GRSDS/H models are ideal for holding popcorn on the top
horizontal shelf and nachos, boxed pizza, or wrapped product
on the bottom, slanted shelf.
GRSDS/H Model — Dual Shelf
GR S D x - xx x HW
Glo-Ray
Sandwich
Width of Unit (inches)
HW = High Wattage
No Character = Standard Watt
No Character = Single Shelf
D = Dual Shelf
T = Triple Shelf
Display
H = Horizontal Shelf
S = Slanted Shelf
S/H = Base Slanted and
Center Horizontal Shelf
Form No. GRSDM-1219
5
English
Model Voltage Watts Amps Plug Configuration Shipping Weight
GRSDH-24D
120 1660 13.8
NEMA 5-15P *
88 lbs. (40 kg)
GRSDH-30D 120 1920 16.0 NEMA 5-20P 100 lbs. (45 kg)
GRSDH-36D
120
†
1170
9.8
NEMA 5-15P ‡
120 lbs. (54 kg)
120/208–240 2340 NEMA L14-20P
GRSDH-41D
120
†
1340
11.2
NEMA 5-15P ‡
137 lbs. (62 kg)
120/208–240 2680 NEMA L14-20P 137 lbs. (62 kg)
GRSDH-52D
120
†
1760
14.7
NEMA 5-15P ‡
172 lbs. (78 kg)
120/208–240 3520 NEMA L14-20P
GRSDH-60D
120/208–240 4200 17.5
NEMA L14-20P ∆
197 lbs. (89 kg)
Model Voltage Watts Amps Plug Configuration Shipping Weight
GRSDH-24 120 830 6.9 NEMA 5-15P 48 lbs. (22 kg)
GRSDH-30 120 970 8.1 NEMA 5-15P 56 lbs. (25 kg)
GRSDH-36 120 1170 9.8 NEMA 5-15P 66 lbs. (30 kg)
GRSDH-41 120 1340 11.2 NEMA 5-15P 74 lbs. (34 kg)
GRSDH-52 120 1760 14.7 NEMA 5-15P * 86 lbs. (39 kg)
GRSDH-60 120/208–240 2100 15.0 NEMA L14-20P 133 lbs. (60 kg)
SPECIFICATIONS
Plug Configurations
Units are supplied from the factory with an electrical cord and
plug installed (plugs are supplied according to the applications).
Some international units may require field installation of the
proper plug.
WARNING
ELECTRIC SHOCK HAZARD: Plug unit into a properly
grounded electrical receptacle of the correct voltage,
size, and plug configuration. If plug and receptacle do not
match, contact a qualified electrician to determine and
install proper voltage and size electrical receptacle.
NOTE: Receptacle not supplied by Hatco.
NEMA 5-15P NEMA 5-20P
NEMA L14-20P NEMA L14-30P
Plug Configurations
Electrical Rating Chart — GRSDH Models, Single Shelf
Electrical Rating Chart — GRSDH Models, Horizontal Dual Shelf
† Not available in Canada
‡ Unit comes equipped with two cord and plug sets, requiring two separate 15 A power circuits. Ratings are for each circuit.
* NEMA 5-20P for Canada
∆ NEMA L14-30P for Canada.
Form No. GRSDM-1219
6
English
Model Voltage Watts Amps Plug Configuration Shipping Weight
GRSDS-24D 120 1355 11.3 NEMA 5-15P 115 lbs. (52 kg)
GRSDS-24DHW 120/208–240 2290 9.7 NEMA L14-20P
115 lbs. (52 kg)
120
†
1165/1125 9.7/9.4 NEMA 5-15P ‡
GRSDS-30D 120 1530 12.8 NEMA 5-15P * 140 lbs. (64 kg)
GRSDS-30DHW 120
†
1400/1450 11.7/12.1 NEMA 5-15P ‡
140 lbs. (64 kg)
120/208–240 2850 12.1 NEMA L14-20P
GRSDS-36D 120 1810 15.1 NEMA 5-20P 160 lbs. (73 kg)
GRSDS-36DHW 120/208–240 3490 14.8 NEMA L14-20P
160 lbs. (73 kg)
120
†
1715/1775 14.3/14.8 NEMA 5-15P ‡
GRSDS-41D 120
†
1090/1030 9.1/8.6 NEMA 5-15P ‡
180 lbs. (82 kg)
120/208–240 2120 9.1 NEMA L14-20P
GRSDS-41DHW 120
†
2010/2070 16.8/17.3 
180 lbs. (82 kg)
120/208–240
†
4080 17.3 NEMA L14-20P
GRSDS-52D 120† 1400/1325 11.7/11.0 NEMA 5-15P ‡
215 lbs. (98 kg)
120/208–240 2725 11.7 NEMA L14-20P
GRSDS-52DHW 120/208–240 5340 22.6 NEMA L14-30P 215 lbs. (98 kg)
GRSDS-60D 120/208–240 3340 14.3 NEMA L14-20P 238 lbs. (108 kg)
Model Voltage Watts Amps Plug Configuration Shipping Weight
GRSDS-24 120 695 5.8 NEMA 5-15P 80 lbs. (36 kg)
GRSDS-24HW 120 1165 9.7 NEMA 5-15P 80 lbs. (36 kg)
GRSDS-30 120 790 6.6 NEMA 5-15P 80 lbs. (36 kg)
GRSDS-30HW
120 1450 12.1 NEMA 5-15P * 80 lbs. (36 kg)
GRSDS-36
120 935 7.8 NEMA 5-15P 92 lbs. (42 kg)
GRSDS-36HW
120 1775 14.8 NEMA 5-15P * 92 lbs. (42 kg)
GRSDS-41
120 1090 9.1 NEMA 5-15P 96 lbs. (44 kg)
GRSDS-41HW
120
†
2070 17.3 NEMA 5-20P 96 lbs. (44 kg)
GRSDS-52
120 1400 11.7 NEMA 5-15P 110 lbs. (50 kg)
GRSDS-52HW
120/208–240 2710 14.8 NEMA L14-20P 110 lbs. (50 kg)
GRSDS-60
120 1715 14.3 NEMA 5-15P * 167 lbs. (76 kg)
SPECIFICATIONS
Electrical Rating Chart — GRSDS Models, Slant Single Shelf
Electrical Rating Chart — GRSDS Models, Slant Dual Shelf
†
Not available in Canada
* NEMA 5-20P for Canada
‡ Unit comes equipped with two cord and plug sets, requiring two separate 15 A power circuits. Ratings are for each circuit.
♦ Unit comes equipped with two cord and plug sets, requiring two separate 20 A power circuits. Ratings are for each circuit.
NOTE: High wattage units have a high wattage output on the top shelf only.
Form No. GRSDM-1219
7
English
Model Voltage Watts Amps Plug Configuration Shipping Weight
GRSDS-24T 120
†
2015 16.8 NEMA 5-20P 164 lbs. (74 kg)
GRSDS-36T 120/208–240 2685 14.6 NEMA L14-20P 219 lbs. (99 kg)
SPECIFICATIONS
Model Voltage Watts Amps Plug Configuration Shipping Weight
GRSDS/H-30D 120 1530 12.8 NEMA 5-15P * 140 lbs. (64 kg)
GRSDS/H-30DHW 120/208–240 2450 11.0 NEMA L14-20P 140 lbs. (64 kg)
GRSDS/H-36D 120 1810 15.1 NEMA 5-20P 158 lbs. (72 kg)
GRSDS/H-36DHW 120/208–240 2910 13.3 NEMA L14-20P 158 lbs. (72 kg)
GRSDS/H-41D 120/208–240 2120 9.1 NEMA L14-20P 178 lbs. (81 kg)
GRSDS/H-41DHW 120/208–240 3360 15.0 NEMA L14-20P 178 lbs. (81 kg)
Electrical Rating Chart — GRSDS Models, Slant Triple Shelf
Electrical Rating Chart — GRSDS/H Models, Slant/Horizontal Dual Shelf
†
Not available in Canada
* NEMA 5-20P for Canada
‡ Unit comes equipped with two cord and plug sets, requiring two separate 15 A power circuits. Ratings are for each circuit.
NOTE: High wattage units have a high wattage output on the top shelf only.
Form No. GRSDM-1219
8
English
Model
Width
(A)
Depth
(B)
Height
(C) •
Shelf
Height (D)
Footprint
Width (E)
Footprint
Depth (F)
GRSDH-24 24
(610 mm)
19-1/2
(495 mm)
12†
(305 mm)
7
(176 mm)
21-1/2
(546 mm)
18
(457 mm)
GRSDH-30 30
(762 mm)
19-1/2
(495 mm)
12†
(305 mm)
7
(176 mm)
27-1/2
(699 mm)
18
(457 mm)
GRSDH-36 36
(914 mm)
19-1/2
(495 mm)
12†
(305 mm)
7
(176 mm)
33-1/2
(851 mm)
18
(457 mm)
GRSDH-41 41
(1041 mm)
19-1/2
(495 mm)
15
(381 mm)
7
(176 mm)
38-1/2
(978 mm)
18
(457 mm)
GRSDH-52 52
(1321 mm)
19-1/2
(495 mm)
15
(381 mm)
7
(176 mm)
49-1/2
(1257 mm)
18
(457 mm)
GRSDH-60 60
(1524 mm)
19-1/2
(495 mm)
15
(381 mm)
7
(176 mm)
57-1/2
(1461 mm)
18
(457 mm)
GRSDH-24D 24
(610 mm)
19-1/2
(495 mm)
25-1/2
(648 mm)
7
(176 mm)
21-1/2
(546 mm)
18
(457 mm)
GRSDH-30D 30
(762 mm)
19-1/2
(495 mm)
25-1/2◘
(648 mm)
7
(176 mm)
27-1/2
(699 mm)
18
(457 mm)
GRSDH-36D 36
(914 mm)
19-1/2
(495 mm)
25-1/2
(648 mm)
7
(176 mm)
33-1/2
(851 mm)
18
(457 mm)
GRSDH-41D 41
(1041 mm)
19-1/2
(495 mm)
25-1/2
(648 mm)
7
(176 mm)
38-1/2
(978 mm)
18
(457 mm)
GRSDH-52D 52
(1321 mm)
19-1/2
(495 mm)
25-1/2
(648 mm)
7
(176 mm)
49-1/2
(1257 mm)
18
(457 mm)
GRSDH-60D 60
(1524 mm)
19-1/2
(495 mm)
25-1/2◘
(648 mm)
7
(176 mm)
57-1/2
(1461 mm)
18
(457 mm)
SPECIFICATIONS
Dimensions — GRSDH Models
GRSDH—Single ShelfGRSDH—Dual Shelf
B
F
A
E
B
F
A
E
C
D
D
D
C
GRSDH Single Shelf and Dual Shelf Dimensions
•
Height includes 4
†

◘

(Canada Only)
Form No. GRSDM-1219
9
English
Model
Width
(A)
Depth
(B)
Height
(C)
Shelf
Height (D)
Footprint
Width (E)
Footprint
Depth (F)
GRSDS-24 24
(610 mm)
24-1/4
(614 mm)
18-5/8†
(473 mm)
9-1/4
(235 mm)
21-1/2
(546 mm)
22-1/2
(572 mm)
GRSDS-30 30
(762 mm)
24-1/4
(614 mm)
18-5/8†
(473 mm)
9-1/4
(235 mm)
27-1/2
(699 mm)
22-1/2
(572 mm)
GRSDS-36 36
(914 mm)
24-1/4
(614 mm)
21-5/8
(548 mm)
9-1/4
(235 mm)
33-1/2
(851 mm)
22-1/2
(572 mm)
GRSDS-41 41
(1041 mm)
24-1/4
(614 mm)
21-5/8
(548 mm)
9-1/4
(235 mm)
38-1/2
(978 mm)
22-1/2
(572 mm)
GRSDS-52 52
(1321 mm)
24-1/4
(614 mm)
21-5/8
(548 mm)
9-1/4
(235 mm)
49-1/2
(1257 mm)
22-1/2
(572 mm)
GRSDS-60 60
(1524 mm)
24-1/4
(614 mm)
21-5/8
(548 mm)
9-1/4
(235 mm)
57-1/2
(1461 mm)
22-1/2
(572 mm)
GRSDS-24D 24
(610 mm)
24-1/4
(614 mm)
32-3/8
(822 mm)
8-1/4
(210 mm)
21-1/2
(546 mm)
22-1/2
(572 mm)
GRSDS-30D 30
(762 mm)
24-1/4
(614 mm)
32-3/8
(822 mm)
8-1/4
(210 mm)
27-1/2
(699 mm)
22-1/2
(572 mm)
GRSDS-36D 36
(914 mm)
24-1/4
(614 mm)
32-3/8
(822 mm)
8-1/4
(210 mm)
33-1/2
(851 mm)
22-1/2
(572 mm)
GRSDS-41D 41
(1041 mm)
24-1/4
(614 mm)
32-3/8
(822 mm)
8-1/4
(210 mm)
38-1/2
(978 mm)
22-1/2
(572 mm)
GRSDS-52D 52
(1321 mm)
24-1/4
(614 mm)
32-3/8
(822 mm)
8-1/4
(210 mm)
49-1/2
(1257 mm)
22-1/2
(572 mm)
GRSDS-60D 60
(1524 mm)
24-1/4
(614 mm)
32-3/8
(822 mm)
8-1/4
(210 mm)
57-1/2
(1461 mm)
22-1/2
(572 mm)
SPECIFICATIONS
Dimensions — GRSDS Models
GRSDS—Single ShelfGRSDS—Dual Shelf
B
F
A
E
B
F
A
E
C
D
D
D
C
GRSDS Single Shelf and Dual Shelf Dimensions
†

Height includes 4
Form No. GRSDM-1219
10
English
Model
Width
(A)
Depth
(B)
Height
(C)
Footprint
Width (D)
Footprint
Depth (E)
GRSDS-24T 24
(610 mm)
24-1/4
(614 mm)
43-7/8
(1114 mm)
21-1/2
(546 mm)
22-1/2
(572 mm)
GRSDS-36T 36
(914 mm)
24-1/4
(614 mm)
43-7/8
(1114 mm)
33-1/2
(851 mm)
22-1/2
(572 mm)
Model
Width
(A)
Depth
(B)
Height
(C)
Top Shelf
Height (D)*
Base Shelf
Height (E)
Footprint
Width (F)
Footprint
Depth (G)
GRSDS/H-30D 30
(762 mm)
24-1/4
(614 mm)
33-1/2
(851 mm)
12
(305 mm)
10-3/8
(264 mm)
27-1/2
(699 mm)
22-1/2
(572 mm)
GRSDS/H-36D 36
(914 mm)
24-1/4
(614 mm)
33-1/2
(851 mm)
12
(305 mm)
10-3/8
(264 mm)
33-1/2
(851 mm)
22-1/2
(572 mm)
GRSDS/H-41D 41
(1041 mm)
24-1/4
(614 mm)
33-1/2
(851 mm)
12
(305 mm)
10-3/8
(264 mm)
38-1/2
(978 mm)
22-1/2
(572 mm)
GRSDS-30DHW 30
(762 mm)
24-1/4
(614 mm)
33-1/2
(851 mm)
12
(305 mm)
10-3/8
(264 mm)
27-1/2
(699 mm)
22-1/2
(572 mm)
GRSDS-36DHW 36
(914 mm)
24-1/4
(614 mm)
33-1/2
(851 mm)
12
(305 mm)
10-3/8
(264 mm)
33-1/2
(851 mm)
22-1/2
(572 mm)
GRSDS-41DHW 41
(1041 mm)
24-1/4
(614 mm)
33-1/2
(851 mm)
12
(305 mm)
10-3/8
(264 mm)
38-1/2
(978 mm)
22-1/2
(572 mm)
SPECIFICATIONS
Dimensions — GRSDS Models, Slant Triple Shelf
A
D
A
F
B
G
B
E
C
C
8-1/4″
(210 mm)
8-1/8″
(206 mm)
8-1/8″
(206 mm)
D
E
GRSDS Triple Shelf Model GRSDS/H Model
GRSDS Triple Shelf and GRSDS/H Dimensions
Height includes 4
Dimensions — GRSDS/H Models
Height includes 4
*
Form No. GRSDM-1219
11
English
INSTALLATION
General
Glo-Ray
®
Merchandising Display Warmers are shipped with
most components pre-assembled. Care should be taken when
unpacking shipping carton to avoid damage to the unit and
components enclosed.
WARNING
ELECTRIC SHOCK HAZARD: Unit is not weatherproof.
Locate unit indoors where ambient air temperature is a
minimum of 70°F (21°C).
Fire Hazard: Locate unit a minimum of 1″ (25 mm) from
combustible walls and materials. If safe distances are not
maintained, discoloration or combustion could occur.
CAUTION
The National Sanitation Foundation (NSF) requires that
units over 36″ (914 mm) in width or weighing more than
80 lbs. (36 kg) either be sealed to or raised above the
installation surface. If unit cannot be sealed at the point
of use, 4″ (102 mm) legs are included to allow for proper
cleaning access below unit.
1. Remove the unit from the carton.
NOTE: To prevent delay in obtaining warranty coverage,
complete online warranty registration. See the
IMPORTANT OWNER INFORMATION section for
details.
2. Remove tape and protective packaging from all surfaces
of the unit.
NOTICE
Do not lay unit on the side with the control panel. Damage
to unit could occur.
Units with two power cords must each be plugged into
individual branch circuits.
Locate the unit in an area where the ambient air temperature
is constant and a minimum of 70°F (21°C). Avoid areas
that may be subject to active air movements or currents
(i.e., near exhaust fans/hoods, air conditioning ducts, and
exterior doors).
3. Carefully lay the unit on its side
and install the four rubber feet.
• Thread a foot stud into the
hole at each corner on the
bottom of the unit. Tighten
securely.
• Slip a rubber foot over each
foot stud.
NOTE:If 4″ (102 mm) legs are
required, refer to the
OPTIONS AND ACCESSORIES section in this
manualforinstallationinstructions.4″(102mm)legs
arestandardon single shelfmodels 36″ (1041mm)
and wider, all dual shelf models, and all triple shelf
models.
4. Slide each glass side panel into the upper channel, then
carefully lower the panel into the lower channel.
Glass Side Panel Installation
5. Install the channel dividers and product divider rods.
• Position the channel dividers onto the locator pins on the
front edge and back edge of the unit.
• Place the product divider rods into the channel dividers.
The rods can be adjusted easily to separate holding
areas as needed.
Product
Divider Rod
Channel
Divider
Locator Pin
Installing Product Divider Rods
NOTE: Unit must be transported in the upright position.
6. Place the unit in the desired location.
• Locate the unit in an area where the ambient air
temperature is constant and a minimum of 70°F
(21°C). Avoid areas that may be subject to active air
movements or currents (i.e., near exhaust fans/hoods,
air conditioning ducts, and exterior doors).
• Make sure the unit is at the proper counter height in an
area convenient for use.
• Make sure the countertop is level and strong enough to
support the weight of the unit and food product.
• Make sure all the feet on the bottom of the unit are
positioned securely on the countertop.
Form No. GRSDM-1219
12
English
OPERATION
General
Use the following procedures to operate the Merchandising
Display Warmers.
WARNING
Read all safety messages in the IMPORTANT SAFETY
INFORMATION section before operating this equipment.
ELECTRIC SHOCK HAZARD: Units with two power cords
must have both power supply cords disconnected before
performing any cleaning, adjustments, or maintenance.
Do not place food product directly onto hardcoat surface.
Food product must be wrapped, boxed, or on a food pan.
NOTICE
Do not slide pans across hardcoat surface, use rough-
bottomed pans, or drop anything on hardcoat surface.
Scratching may occur. Damage to hardcoat surface
caused by misuse is not covered under warranty.
Control Panel Symbols
The following are descriptions of the symbols on the control
panel. All symbols and controls are located on the control panel
at the back of the unit.
Heat Source Icon — (Bottom Heat)
The heat source icon consists of a bar with heat waves and
appears next to the temperature control for each heat source.
The location of the heat waves, either above or below the bar,
indicates whether the knob/switch controls bottom heat or
overhead heat.
Shelf Indicator —
The shelf indicator is a number that corresponds to the shelf
that the knob/switch controls. “1” refers to the bottom shelf or
base of the unit.
Startup
1. Plug the unit into a properly grounded electrical outlet of
the correct voltage, size, and plug configuration. See the
SPECIFICATIONS section for details.
• Units with two power cords must each be plugged into
individual branch circuits.
2. Move the Power I/O (on/off) switch(es) to the I (on)
position.
• The overhead strip heaters and overhead lights will turn
on.
• The heated base/shelves will energize.
NOTE:All Power I/O (on/off) switches must be in the I
(on)positionfortheheatedbase/shelvestofunction.
CAUTION
BURN HAZARD: Some exterior surfaces on unit will get
hot. Use caution when touching these areas.
3. Turn the Temperature Control(s) to the desired temperature
setting. The operating temperature range of the heated
base/shelves is from room temperature to approximately
185°–200°F (85°–93°C).
• Turning the Temperature Control clockwise will increase
the temperature setting. Turning the Temperature
Control counterclockwise will decrease the temperature
setting.
NOTE: Each heated base/shelf is controlled independently.
Power I/O
(on/off) Switch
(Top Shelf)
Temperature
Control
(Top Shelf)
Power I/O
(on/off) Switch
(Bottom Shelf)
Temperature
Control
(Bottom Shelf)
Controls
NOTE: If the unit is equipped with a Digital Temperature
Controller(s) instead of the standard Temperature
Control knob(s), see the OPTIONS AND
ACCESSORIES section for operation instructions.
4. Allow the unit 30 minutes to reach operating temperature
before placing preheated food product.
Shutdown
1. Move the Power I/O (on/off) switch(es) to the O (off)
position. The overhead strip heaters, overhead lights, and
heated base/shelves will shut off.
Form No. GRSDM-1219
13
English
MAINTENANCE
General
Hatco Glo-Ray
®
Merchandising Display Warmers are designed
for maximum durability and performance with minimum
maintenance.
WARNING
ELECTRIC SHOCK HAZARD:
• Turn OFF power switch, unplug power cord, and allow
unit to cool before performing any cleaning, setup, or
maintenance.
• Units with two power cords must have both power
supply cords disconnected before performing any
cleaning, adjustments, or maintenance.
• DO NOT submerge or saturate with water. Unit is not
waterproof. Do not operate if unit has been submerged
or saturated with water.
• Do not steam clean or use excessive water on unit.
• Do not clean unit when it is energized or hot.
This unit has no “user-serviceable” parts. If service
is required on this unit, contact an Authorized Hatco
Service Agent or contact the Hatco Service Department at
800-558-0607 or 414-671-6350.
Daily Cleaning
To preserve the finish of the unit as well as maintain
performance, it is recommended that the unit be cleaned daily.
NOTICE
IMPORTANT—DO NOT use paper towel or glass cleaner
to clean plastic surfaces such as sneeze guards and
flip-up doors. Paper towel and glass cleaner may scratch
the material. Wipe off plastic surfaces using a soft, clean,
water-dampened cloth.
Clean unit daily to avoid malfunctions and maintain
sanitary operation.
1. Turn off the unit, unplug the power cord(s), and allow the
unit to cool.
• Units with two power cords must have both power
supply cords disconnected before performing any
cleaning, adjustments, or maintenance.
2. Remove and wipe down the product divider rods and
channel dividers.
3. Wipe down all exterior and interior surfaces using a water-
dampened cloth. A non-abrasive cleaner may be used for
difficult stains. Hard to reach areas should be cleaned
using small brush and mild soap.
4. Clean the glass side panels using a standard glass
cleaner.
5. Clean the plastic sneeze guards and flip-up doors (if
equipped) using soft cleaning cloths, mild soap, and water,
if equipped. NOTICE: Do not use paper towel or glass
cleaner on plastic surfaces — scratching may occur.
Replacing Display Light Bulbs
WARNING
Use only light bulbs that meet or exceed National
Sanitation Foundation (NSF) standards and are specifically
designed for food holding areas. Breakage of light bulbs
not specially coated could result in personal injury and/or
food contamination.
The display light is an incandescent light bulb that illuminates
the warming area. The bulb has a special coating to guard
against injury and food contamination in the event of breakage.
1. Turn off the unit, unplug the power cord(s), and allow the
unit to cool.
• Units with two power cords must have both power
supply cords disconnected before performing any
cleaning, adjustments, or maintenance.
2. Unscrew the light bulb from the unit and replace it with a
new, specially-coated incandescent light bulb.
NOTE: Hatco shatter-resistant light bulbs meet NSF
standards for food holding and display areas. For
120and120/208–240Vapplications,useHatcoP/N
02.30.043.00.
NOTE: Shatter-resistant halogen bulbs are available in place
of the standard incandescent bulbs. Halogen bulbs
have a special coating to guard against injury and
food contamination in the event of breakage. For
120and120/208–240Vapplications,useHatcoP/N
02.30.081.00.
WARNING
ELECTRIC SHOCK HAZARD: Use only Genuine Hatco
Replacement Parts when service is required. Failure to use
Genuine Hatco Replacement Parts will void all warranties
and may subject operators of the equipment to hazardous
electrical voltage, resulting in electrical shock or burn.
Genuine Hatco Replacement Parts are specified to operate
safely in the environments in which they are used. Some
aftermarket or generic replacement parts do not have the
characteristics that will allow them to operate safely in
Hatco equipment.
Form No. GRSDM-1219
14
English
Symptom Probable Cause Corrective Action
Unit is on, but no lights. Light bulb defective. Replace light bulb.
Blown fuse. Replace blown fuse. Follow “Replacing a Fuse” procedure in
the MAINTENANCE section.
Food cavity not hot enough. Temperature Control set too low. Adjust Temperature Control to a higher setting.
Heating element(s) not working.
Contact Authorized Service Agent or Hatco for assistance.
Temperature Control not working properly.
Excessive air movement around unit. Restrict or redirect air movement (i.e., air conditioning duct
or exhaust fan) away from unit or install flip-up doors on unit
to contain heat and block air flow.
Unit connected to incorrect power supply. Contact Authorized Service Agent or Hatco for assistance.
Food cavity too hot. Temperature Control set too high. Adjust Temperature Control to a lower setting.
Temperature Control not working properly.
Contact Authorized Service Agent or Hatco for assistance.
Unit connected to incorrect power supply.
No heat, but light works. Temperature Control set too low. Adjust Temperature Control to a higher setting.
Heating element(s) not working.
Contact Authorized Service Agent or Hatco for assistance.
Temperature Control not working properly.
No heat and no light. Power turned OFF. Move Power I/O (on/off) switch(es) to the I (on) position.
Circuit breaker tripped. Reset circuit breaker. If circuit breaker continues to trip,
contact Authorized Service Agent or Hatco for assistance.
TROUBLESHOOTING GUIDE
WARNING
This unit must be serviced by qualified personnel only.
Service by unqualified personnel may lead to electric
shock or burn.
WARNING
ELECTRIC SHOCK HAZARD: Turn OFF power switch,
unplug power cord, and allow unit to cool before
performing any cleaning, setup, or maintenance.
Troubleshooting Questions?
If you continue to have problems resolving an issue, please contact the nearest Authorized Hatco Service Agency or Hatco for
assistance. To locate the nearest Service Agency, log onto the Hatco website at www.hatcocorp.com, select the Support pull-
down menu, and click on “Find A Service Agent”; or contact the Hatco Parts and Service Team at:
Telephone: 800-558-0607 or 414-671-6350
e-mail: [email protected]
Form No. GRSDM-1219
15
English
OPTIONS AND ACCESSORIES
Digital Temperature Controller
Units may be equipped with an optional digital temperature
controller that regulates and displays the base/shelf
temperature(s). Use the following procedures to operate the
digital temperature controller.
NOTE: This option is factory installed only, not available for
retrofit.
NOTE: Units manufactured for use outside the United States
and Canada will have digital temperature controllers
thatindicatetemperatureinCelsius(°C).
Down Arrow
Key
Up Arrow
Key
“out 1”
Fahrenheit
Symbol
SET
Key
Digital Temperature Controller
1. Move the unit Power I/O (on/off) switch to the I (on)
position.
• The digital temperature controller will energize and
the current temperature of the heated base/shelves
will appear on the display. CAUTION! Some exterior
surfaces on the unit will get hot. Use caution when
touching these areas.
• The phrase “out 1” will appear in the upper left corner of
the display to show that the base is in heat mode.
2. Press and release the key. The current setpoint
temperature will be shown on the display and ”out 1” will
flash in the upper left corner.
3. Press the key or key within 15 seconds to
change the setpoint temperature. If no key is pressed
within 15 seconds, the display will revert to the current
temperature of the heated base(s)
4. Press the key or wait 15 seconds to lock in the new
setpoint temperature. The setpoint temperature range of
the controller is from room temperature to the maximum
operating temperature of the unit.
Locking/Unlocking the Digital Temperature
Controller
The keys on the digital temperature controller can be locked to
prevent unauthorized changes to the settings.
To lock the keys of the digital temperature controller:
• Press and hold both the key and key at the
same time for over two seconds. The message “Loc” will
appear on the display.
To unlock the keys of the digital temperature controller:
• Press and hold both the key and key at the
same time until the message “UnL” appears on the display.
Sneeze Guards
Optional sneeze guards are available for the all models.
GRSDH models can be fitted with sneeze guards above each
shelf on both sides of the unit. GRSDS and GRSDS/H models
can be fitted with sneeze guards above each shelf on the
customer side of the unit only. Use the following procedure to
install sneeze guards.
1. Remove the screws from the face of the unit that align with
the holes in the sneeze guard.
2. Align the holes on the sneeze guard with the screw holes
on the unit.
3. Insert the screws removed in step 1 through the sneeze
guard and into the unit.
4. Tighten the screws until the sneeze guard is secure. Do
not over-tighten the screws.
Sneeze Guard
Screw
GRSDS Model Sneeze Guard Installation
Display Sign Holder
A display sign holder (sign not included) is available
for installation on the top or intermediate shelf. The sign holder
is installed by simply attaching the magnetic side of the sign
holder to the desired shelf.
Magnet
Sign Holder
Display Sign Holder
Form No. GRSDM-1219
16
English
OPTIONS AND ACCESSORIES
4″ (102 mm) Adjustable Legs
NOTICE
Do not lay unit on the side with the control panel or
damage to unit could occur.
Carefully lay unit on its side. Install legs to bottom of unit. Hand-
tighten legs until snug. Do not over-tighten. Return unit to the
upright position.
Lengthen
Shorten
Leg Adjustment
Leg Installation
NOTE: Legs are adjustable for leveling the unit. Use
a 5/8″ (16 mm) open-end wrench to make leveling
adjustments once the unit is placed in final position.
Stainless Steel End Panels
Stainless steel end panels are factory installed options in place
of the glass end panels.
Flip-Up Door Locking Plates
Flip-up door locking plates are factory installed and are
available as options for GRSDS-XX, GRSDS-XXD, and
GRSDS-XXT models. Flip-up door locking plates allow access
to the server side only.
Halogen Display Lights
Optional halogen display light bulbs can be ordered in place of
the standard 120 V incandescent display light bulbs.
Divider Rods
Additional divider rods are available to help keep product
separate in the channels.
12″ Shelf Height Spacing
(GRSDH-XXD Models Only)
         

It is available for GRSDH-XXD models on the top shelf only.
Chef LED Bulbs
Chef LED bulbs are available for all models. CHEF LED bulbs
are LED light bulbs that offer energy savings over incandescent
bulbs.
Flip-Up Doors
Flip-up doors are available as accessories for all models. The
doors can be installed to each shelf on either the customer
side or operator side of the unit. Use the following procedure to
install flip-up doors (the procedure is the same for either side
as well as each shelf).
NOTE:Units 52″ (1321mm) andlarger require2 doorsper
shelf and a center mounting bracket.
1. Remove the two screws from the element end cover above
the desired shelf on each side of the unit.
2. Align the holes on the mounting brackets with the screw
holes on the element end covers of the unit.
3. Insert the screws removed in step 1 through the mounting
brackets and into the unit. Tighten securely.
NOTE:Forunits52″(1321mm)andlarger,acentermounting
bracket is required. Remove the screws from the center
of the middle or top housing and use them to mount the
center mounting bracket.
4. Place a spacer on each hinge screw (both included with door).
5. Align the screw holes at each end of the channel on the
flip-up door with the hole on each mounting bracket.
6. Insert a hinge screw with spacer through each mounting
bracket and into the flip-up door.
7. Tighten the hinge screws until the flip-up door is secure.
Make sure the spacers on the hinge screws go through
the holes in the mounting brackets. Do not over-tighten the
screws.
Mounting
Bracket
End
Cover
Screw
End
Cover
Hinge
Screw
Spacer
Flip-Up
Door
Mounting
Bracket
Mounting
Bracket
End Cover
Screw
Flip-Up Door Installation
Form No. GRSDM-1219
17
English
LIMITED WARRANTY
1. PRODUCT WARRANTY
Hatco warrants the products that it manufactures (the
“Products”) to be free from defects in materials and
workmanship, under normal use and service, for a period of
one (1) year from the date of purchase when installed and
maintained in accordance with Hatco’s written instructions
or 18 months from the date of shipment from Hatco. Buyer
must establish the Product’s purchase date by registering the
Product with Hatco or by other means satisfactory to Hatco in
its sole discretion.
Hatco warrants the following Product components to be free
from defects in materials and workmanship from the date of
purchase (subject to the foregoing conditions) for the period(s)
of time and on the conditions listed below:
a) One (1) Year Parts and Labor PLUS One (1) Additional
Year Parts-Only Warranty:
Conveyor Toaster Elements (metal sheathed)
Drawer Warmer Elements (metal sheathed)
Drawer Warmer Drawer Rollers and Slides
Strip Heater Elements (metal sheathed)
Display Warmer Elements (metal sheathed air heating)
Holding Cabinet Elements (metal sheathed air heating)
Heated Well Elements — HW and HWB Series
(metal sheathed)
b) Two (2) Year Parts and Labor Warranty:
Induction Ranges
Induction Warmers
c) One (1) Year Parts and Labor PLUS Four (4) Years
Parts-Only Warranty:
3CS and FR Tanks
d) One (1) Year Parts and Labor PLUS Nine (9) Years
Parts-Only Warranty on:
Electric Booster Heater Tanks
Gas Booster Heater Tanks
e) Ninety (90) Day Parts-Only Warranty:
Replacement Parts
THE FOREGOING WARRANTIES ARE EXCLUSIVE AND
IN LIEU OF ANY OTHER WARRANTY, EXPRESSED OR
IMPLIED, INCLUDING BUT NOT LIMITED TO ANY IMPLIED
WARRANTY OF MERCHANTABILITY OR FITNESS FOR
A PARTICULAR PURPOSE OR PATENT OR OTHER
INTELLECTUAL PROPERTY RIGHT INFRINGEMENT. Without
limiting the generality of the foregoing, SUCH WARRANTIES
DO NOT COVER: Coated incandescent light bulbs, fluorescent
lights, heat lamp bulbs, coated halogen light bulbs, halogen
heat lamp bulbs, xenon light bulbs, LED light tubes, glass
components, and fuses; Product failure in booster tank, fin
tube heat exchanger, or other water heating equipment caused
by liming, sediment buildup, chemical attack, or freezing;
or Product misuse, tampering or misapplication, improper
installation, or application of improper voltage.
2. LIMITATION OF REMEDIES AND DAMAGES
Hatco’s liability and Buyer’s exclusive remedy hereunder will
be limited solely, at Hatco’s option, to repair or replacement
using new or refurbished parts or Product by Hatco or a Hatco-
authorized service agency (other than where Buyer is located
outside of the United States, Canada, United Kingdom, or
Australia, in which case Hatco’s liability and Buyer’s exclusive
remedy hereunder will be limited solely to replacement of part
under warranty) with respect to any claim made within the
applicable warranty period referred to above. Hatco reserves
the right to accept or reject any such claim in whole or in part. In
the context of this Limited Warranty, “refurbished” means a part
or Product that has been returned to its original specifications
by Hatco or a Hatco-authorized service agency. Hatco will not
accept the return of any Product without prior written approval
from Hatco, and all such approved returns shall be made
at Buyer’s sole expense. HATCO WILL NOT BE LIABLE,
UNDER ANY CIRCUMSTANCES, FOR CONSEQUENTIAL
OR INCIDENTAL DAMAGES, INCLUDING BUT NOT LIMITED
TO LABOR COSTS OR LOST PROFITS RESULTING FROM
THE USE OF OR INABILITY TO USE THE PRODUCTS OR
FROM THE PRODUCTS BEING INCORPORATED IN OR
BECOMING A COMPONENT OF ANY OTHER PRODUCT OR
GOODS.
18
Formulaire n° GRSDM-1219
Français
SOMMAIRE
Les consignes de sécurité qui apparaissent dans ce manuel
sont identifiées par les mots indicateurs suivants :
AVERTISSEMENT
AVERTISSEMENT indique une situation dangereuse qui,
si elle n’est pas évitée, peut provoquer la mort ou des
blessures graves.
ATTENTION
ATTENTION indique une situation dangereuse qui, si elle
n’est pas évitée, peut provoquer des blessures légères ou
moyennes.
AVIS
AVIS est utilisé pour des questions sans rapport avec des
blessures corporelles.
INTRODUCTION
Le présentoir chauffant /présentoir Glo-Ray
®
de Hatco sont
parfait pour l’attente des sandwiches enveloppés ou des
pizza emballées sur une ligne de buffet ou dans une région
de service temporaire. Ces présentoirs chauffants contiennent
les produits emballés chauds et les maintiennent à une
température de service optimale sans affecter leur qualité. Une
chaleur infrarouge venant du sommet et une base chauffante
thermoscope étendent les périodes d’attente de la plupart des
aliments emballés. Les éléments chauffants infrarouge sont
garantis contre toute rupture et panne électrique pour une
période de deux ans. Ces appareils possèdent également
des lampes à incandescence et un cordon l’alimentation muni
d’une fiche.
Les présentoirs chauffants Glo-Ray sont le produit de
recherches intensives et de tests sur le terrain. Les matériaux
utilisés ont été sélectionnés pour une durabilité maximale, une
apparence attractive et des performances optimales. Chaque
unité est soigneusement inspectée et testée avant expédition.
Ce manuel fournit des instructions d’installation, de sécurité
et de fonctionnement pour les présentoirs chauffants Glo-Ray.
Hatco vous recommande de lire l’ensemble des instructions
d’installation, de sécurité et de fonctionnement contenues dans
ce manuel avant d’installer et d’utiliser l’appareil.
Informations Importantes pour le Propriétaire ................18
Introduction .........................................................................18
Consignes de Sécurité Importantes ................................. 19
Description du Modèle .......................................................20
Tous les modèles ...............................................................20
Modèles GRSDH ............................................................... 20
Modèles GRSDS ...............................................................20
Modèles GRSDS/H ............................................................20
Désignation du Modèle ...................................................... 21
Caractéristiques Techniques ............................................21
Configuration des fiches .................................................... 21
Tableau des valeurs nominales électriques ......................21
Dimensions ........................................................................ 24
Installation ...........................................................................27
Généralités ........................................................................27
Mode d’emploi ....................................................................28
Généralités ........................................................................28
Maintenance ........................................................................29
Généralités ........................................................................29
Nettoyage quotidien ...........................................................29
Remplacement du tube d’éclairage ...................................29
Guide de Dépannage ..........................................................30
Options et accessoires ...................................................... 31
Garantie Limitée .................................................................33
Distributeurs de pièces autorisés ........Couverture Arrière
INFORMATIONS IMPORTANTES POUR LE PROPRIÉTAIRE
Notez le numéro de modèle, le numéro de série, la tension
et la date d’achat de l’appareil dans les espaces ci-dessous
(étiquette de spécification située sur le côté de l’appareil).
Veuillez avoir cette information à portée de la main si vous
appelez Hatco pour assistance.
Modèle No. ______________________________________
Numéro de série __________________________________
Voltage _________________________________________
Date d’achat _____________________________________
Enregistrez votre appareil!
Remplissez la garantie en ligne pour éviter les retards
pour faire jouer la garantie. Accédez au site Web Hatco
www.hatcocorp.com, sélectionnez le menu déroulant
Support (Assistance), puis cliquez sur « Warranty » (Garantie).
Horaires
ouvrables : 7h00 à 17h00 du lundi au vendredi
Heure du Centre (CT)
(Horaires d’été : juin à septembre—
7h00 à 17h00 du lundi au jeudi
7h00 à 16h00 le vendredi)
Téléphone: 800-558-0607; 414-671-6350
Courriel: [email protected]
Service d'assistance et de pièces de
rechange disponible 7j/7, 24h/24 aux
États-Unis et au Canada en composant
le 800-558-0607.
Des renseignements supplémentaires sont disponibles sur
notre site Web à www.hatcocorp.com.
Formulaire n° GRSDM-1219
19
Français
CONSIGNES DE SÉCURITÉ IMPORTANTES
AVERTISSEMENT
DANGER D’INCENDIE : Placez l’unité à au moins
25 mm (1″) des murs combustibles et des produits. Si
les distances de sécurité ne sont pas respectées, une
décoloration ou combustion peut avoir lieu.
N’utiliser que des ampoules électriques qui correspondent
ou qui surpassent les standards de la Fondation Nationale
des Affaires Sanitaires (NSF) et qui sont spécifiquement
conçus pour les espaces de conservation des aliments.
La casse d’ampoules électriques non enduites de manière
spécifique pourrait entraîner des lésions corporelles et/ou
une contamination des aliments.
Assurez-vous que tous les opérateurs ont été formés à
l’utilisation sûre et correcte de l’appareil.
Cet appareil ne doit pas être utilisé par des enfants ou des
personnes avec des capacités physiques, sensorielles ou
mentales diminuées. Assurez-vous que les enfants sont
bien surveillés et tenez-les à l’écart de l’appareil.
S’assurer que le produit alimentaire a été chauffé à une
température adaptée au maintien de sa salubrité avant de
le mettre dans l’appareil sous peine de risques graves pour
la santé. Cet appareil est destiné au maintien au chaud de
produits alimentaires préchauffés uniquement.
Ne placez aucun produit alimentaire directement sur
une surface à revêtement dur. Les produits alimentaires
doivent être emballés, placés dans une boîte ou dans un
bac alimentaire.
Cet appareil ne contient aucune pièce réparable par
l’utilisateur. Si cet appareil doit être réparé, contacter un
réparateur Hatco agréé ou le Service après-vente Hatco au
800-558-0607 ou 414-671-6350.
ATTENTION
DANGER DE BRÛLURE : Certaines surfaces extérieures
de l’appareil deviennent chaudes. Toucher ces zones de
l’appareil avec précaution.
Placez l’unité à une hauteur adaptée au comptoir, à un
emplacement pratique à utiliser. L’emplacement doit être
plan pour éviter que l’unité ou son contenu ne tombe
accidentellement, et suffisamment solide pour supporter
le poids de l’unité et de son contenu.
La National Sanitation Foundation (NSF) exige que les
appareils mesurant plus de 914 mm (36″) de largeur et
pesant plus de 36 kg (80 lbs.) soient hermétiquement fixés
ou rehaussés sur la surface d’installation. Si l’unité ne
peut pas être fixée à l’endroit d’utilisation, des pieds de
102 mm (4″) sont fournis pour permettre le nettoyage du
dessous de l’unité.
AVERTISSEMENT
DANGER DE DÉCHARGE ÉLECTRIQUE :
• Brancher l’appareil sur une prise de courant avec terre
de tension, de format et de configuration des broches
corrects. Si la fiche et la prise ne se correspondent pas,
s’adresser à un électricien qualifié pour déterminer et
installer une prise de courant de format et de tension
corrects.
• Mettez l’unité hors tension depuis l’interrupteur,
débranchez le cordon d’alimentation et laissez l’unité
refroidir avant d’effectuer tout nettoyage, tout réglage
ou tout entretien.
• Si les appareils sont dotés de deux cordons
d’alimentation, ces derniers doivent tous deux être
débranchés avant d’effectuer tout nettoyage, réglage
ou entretien de l’appareil.
• NE PAS immerger l’appareil ni le saturer d’eau.
L’appareil n’est pas étanche à l’eau. Ne pas le faire
fonctionner s’il a été immergé ou saturé d’eau.
• L’appareil n’est pas à l’épreuve des intempéries. Placer
l’appareil à l’intérieur à une température ambiante de
21°C (70°F) minimum.
• Ne tirez pas l’unité par le cordon d’alimentation.
• Interrompez l’utilisation de l’unité si le cordon
d’alimentation est effiloché ou usé.
• N’essayez jamais de réparer ou de remplacer un cordon
d’alimentation. Celui-ci devra être remplacé par Hatco,
un agent de service agréé par Hatco ou une personne
possédant des qualifications similaires.
• Ne pas nettoyer à la vapeur ni utiliser trop d’eau sur
l’appareil.
• Cet appareil n’est pas étanche aux jets. Ne pas utiliser
de jet sous pression pour nettoyer l’appareil.
• Ne pas nettoyer l’appareil lorsqu’il est sous tension.
• Cet appareil doit uniquement être réparé par un
personnel qualifié. Toute réparation par un personnel
non qualifié peut entraîner une électrocution et des
brûlures.
• Pour les réparations, utiliser exclusivement des pièces
de rechange Hatco d’origine. Utilisez des pièces
détachées Hatco authentiques sous peine d’annuler
toutes les garanties et d’exposer l’utilisateur à des
tensions électriques dangereuses pouvant entraîner
une électrocution ou des brûlures. Les pièces
de rechange Hatco d’origine sont conçues pour
fonctionner sans danger dans les environnements
dans lesquels elles sont utilisées. Certaines pièces
de rechange génériques ou de second marché ne
présentent pas les caractéristiques leur permettant de
fonctionner sans danger dans la matériel Hatco.
Lisez l’information de securite importante suivante avant d’utiliser cet équipement pour éviter
des dommages ou la mort sérieux et pour éviter d’endommager l’équipement ou la propriété.
20
Formulaire n° GRSDM-1219
Français
CONSIGNES DE SÉCURITÉ IMPORTANTES
Tous les Modèles
Tous les présentoirs chauffants Hatco Glo-Ray
®
sont fabriqués
en aluminium, acier inoxydable et acier zingué. Les accessoires
comprennent des panneaux latéraux en verre trempé, une base
chauffante réglable par thermostat, des éléments chauffants
supérieurs à infrarouges, des lumières à incandescence, des
barres de séparation des produits, des pieds, ainsi qu’un jeu
comprenant un cordon d’alimentation et une fiche. La plage
de température de service est comprise entre la température
ambiante et 85°C–93°C (185°–200°F).
Modèles GRSDH
Les modèles GRSDH sont des présentoirs chauffants à
rayonnages horizontaux conçus pour contenir des produits
enveloppés. Ces modèles peuvent être commandés dans

disponibles avec un rayonnage simple ou double.
Modèle GRSDH — Rayonnage Simple
Modèles GRSDS
Les modèles GRSDS sont des présentoirs chauffants à
rayonnages inclinés conçus pour contenir des produits
enveloppés. Ces rayonnages sont inclinés pour le côté
pratique de la restauration self-service. Ces modèles peuvent
être commandés dans différentes largeurs, de 610 à 1524 mm

    
disponibles en modèles à rayonnage triple.
Modèle GRSDS — Rayonnage Double
Modèles GRSDS/H
Les modèles GRSDS/H sont des unités à rayonnage double
comprenant un rayonnage incliné et un rayonnage horizontal.
Ces modèles peuvent être commandés dans différentes

puissance en watts plus élevée est disponible en option pour le
rayonnage supérieur. Les modèles GRSDS/H sont idéaux pour
contenir du popcorn sur le rayonnage horizontal supérieur et
des nachos, des pizzas en boîte ou des produits emballés sur
le rayonnage incliné inférieur.
Modèle GRSDS/H Model — Rayonnage Double
DESCRIPTION DU MODÈLE
AVIS
Ne couchez pas l’unité sur le côté comportant le panneau
de commande. L’unité pourrait être endommagée.
Si les appareils sont dotés de deux cordons d’alimentation,
ils doivent être connectés à des circuits en dérivation
distincts.
Utilisez uniquement des nettoyants non abrasifs et des
chiffons doux. Les chiffons et nettoyant abrasifs pourraient
rayer la finition de l’unité, altérant son apparence et la
rendant vulnérable à l’accumulation de saleté. Utilisation
de matériaux abrasifs annulera la garantie.
IMPORTANT—N’UTILISEZ JAMAIS une serviette en papier
ou un nettoyant pour vitres sur les surfaces en plastique
telles que les pare-haleine ou les capots rabattables. Les
serviettes en papier et le nettoyant pour vitres peuvent
rayer l’équipement. Essuyez les surfaces plastique à l’aide
d’un chiffon doux, propre et humide.
AVIS
Ne faites pas glisser de casseroles sur les surfaces
à revêtement dur, n’utilisez pas de casseroles avec
revêtement à fond dur et ne laissez rien tomber sur
les surfaces à couche dure. Cela pourrait rayer votre
équipement. Les dommages causés sur les surfaces à
revêtement dur dus à une mauvaise utilisation ne sont pas
couverts par la garantie.
Nettoyez l’unité quotidiennement pour év iter les
dysfonctionnements et assurer un fonctionnement sain.
Placez l’unité dans une zone dont la température ambiante
est constante 21°C minimum (70°F). Évitez les endroits
susceptibles d’activer les mouvements ou les courants
d’air.
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16
  • Page 17 17
  • Page 18 18
  • Page 19 19
  • Page 20 20
  • Page 21 21
  • Page 22 22
  • Page 23 23
  • Page 24 24
  • Page 25 25
  • Page 26 26
  • Page 27 27
  • Page 28 28
  • Page 29 29
  • Page 30 30
  • Page 31 31
  • Page 32 32
  • Page 33 33
  • Page 34 34
  • Page 35 35
  • Page 36 36

Hatco GRSDH, GRSDS, GRSDS/H Series Le manuel du propriétaire

Hatco
Marque
Hatco
Modèle
GRSDH, GRSDS, GRSDS/H Series
Taper
Le manuel du propriétaire
Télécharger le PDF
rapport

dans d''autres langues

Documents connexes

Autres documents