Viper DS4VB+ Le manuel du propriétaire

Table of Contents

Congratulations ..........................................................................1

Important Information ..................................................................2

Government Regulations and Safety Information .....................2

Your Warranty ..................................................................... 2

Replacement Remote Controls ................................................2

Introduction .................................................................................3

Control Center ..................................................................... 3

Using the System .......................................................................... 4

Arm/Lock ...........................................................................4

Disarm/Unlock ....................................................................4

Start Engine ........................................................................4

Stop Engine .......................................................................5

Valet Mode .........................................................................5

Battery Information .......................................................................6

Low Battery Alert ................................................................6

Battery Replacement ............................................................. 6

Battery Disposal ..................................................................7

Patent Information ........................................................................7

Government Regulations ...............................................................8

Warning! Safety First .................................................................. 10

Limited Lifetime Consumer Warranty .............................................13

Congratulations

Congratulations on the purchase of your state-of-the-art Directed

Digital System. Reading this Owner’s Guide prior to using your

system will help maximize the use its many features. For more

information please visit us online (see back cover for URL). For

any additional questions please contact your authorized Directed

dealer or Directed at 1-800-753-0600. Additional support is also

available at: http://support.directed.com.

Note: Your system is conﬁgurable and may or may not include

features such as remote start or security. This guide also covers

optional features which may not be applicable to your system.

Please speak with your installation technician to ﬁnd out which

features are applicable.

2

Important Information

Government Regulations and Safety Information

Read the Government Regulations and Warning!

Safety First sections of this manual prior to operating

this system.

WARNING! Failure to heed this information can result

in death, personal injury or property damage and may

also result in the illegal use of the system beyond its

intended purpose.

Your Warranty

Your system comes with a warranty. The warranty terms are de-

tailed at the end of this guide. Make sure that you receive the

proof of purchase from your dealer, indicating the product was

installed by an authorized Directed dealer.

Replacement Remote Controls

Please see your authorized dealer or visit us at www.directedstore.

com to order additional remote controls. Remote control RPN (Re-

placement Part Number) are typically found on the back of the

device.

3

Introduction

Control Center

Status LED

Valet/Control

Center Button

In-vehicle System Antenna

The Control Center sends and receives commands or messages to

and from the system. It consists of:

• The antenna, for system communication.

• The Status LED, as a visual indicator of the system’s status.

• Valet button, for accessing various feature, programming,

and reporting functions of the system.

4

Using the System

Arm/Lock

Press and release the remote control button. The vehicle doors

lock, siren/horn sound, parking lights ﬂash once, and alarm* fea-

tures are enabled. If a Trigger Zone Fault is detected, the siren

chirps once again, and the Control Center LED generates a Trig-

ger Fault Zone report.*

Disarm/Unlock

Press and release the remote control button, then press and release

it a second time. The vehicle doors unlock, siren/horn sound,

parking lights ﬂash twice, and alarm* features are disabled. An

Alarm Report* alert of four or ﬁve siren chirps will replace the

normal disarm chirps, if the alarm was triggered.

Start Engine

When the engine is OFF, press and hold the remote control button

to start the engine. If the remote start fails to turn on, the vehicle

parking lights will ﬂash to indicate the cause. Refer to the following

table for the likely cause.

Alert Conditions:

Parking Light

Flashes*

Possible Cause Solution

5 Brake ON. Release Foot Brake.

6 Hood Open. Close Hood.

7

After performing Remote Start

command MTS not enabled.

Enabled MTS Mode.

9 Start Valet ON. Turn Start Valet OFF.

* Available for systems with security features only.

5

Stop Engine

When the engine is ON with Remote Start, press and hold the

remote control button. The engine stops run ning and the parking

lights turn OFF.

Valet Mode

Start Valet mode disables remote start features until turned off.

Use the following routine to manually turn on/off the Start Valet

Mode:

1. Turn the ignition ON and then OFF.

2. Press and hold the Valet button for ﬁve seconds.

The parking lights ﬂash nine times in rapid succession when

turned on, and nine times in slow succession when turned

off.

Emergency Override*

The following procedure Disarms the system when a programmed

remote is not available. Number of presses__________

1. Turn the ignition ON.

2. Press and release the Control Center button the correct num-

ber of times (the default is once).

After a few seconds the siren output ceases and the system

is disarmed.

* Available for systems with security features only.

6

Battery Information

The 2-way remote 7816*, is powered by two coin cell batteries

(CR-2016), and the 1-way remote 7616, is powered by a single

coin cell battery (CR-2016). Operating range diminishes as bat-

tery charge depletes.

Low Battery Alert

When unlocking the vehicle using a remote control with a low

battery charge, the system provides a notiﬁcation by emitting a

third horn honk output (if connected). If conﬁrmation chirps are

programmed off, the system still emits one horn honk when unlock-

ing. After performing a command with the remote control, sever-

al beeps play to indicate the battery/batteries need replacing.

Once the alerts begin, the remote control will remain operational

for several days but the battery/batteries should be replaced at

the earliest opportunity or failure to control the system may occur.

Battery Replacement

1. Unscrew the hardware on unit rear and remove from hous-

ing (if present).

2. Use a small ﬂat blade screwdriver and insert it into the slot

located along the bottom of the remote, near the key ring.

Carefully pry open the case.

3. Gently slide out the used battery/batteries to remove it from

the holding clip. Orient the new battery for the correct polar-

ity and insert into holding clip.

4. Realign the case parts and snap together by pressing ﬁrmly

and evenly on the front and back. Reinstall screw (if present).

7

Battery Disposal

Directed cares about the environment. If you need to

dispose of the battery, please do so in accordance with

your municipal requirements for battery disposal.

* Note: Your system may not include the 2-way remote (7816).

Patent Information

This product is covered by one or more of the following United

States patents:

Remote Start Patents:

5,349,931; 5,872,519; 5,914,667; 5,952,933;

5,945,936; 5,990,786; 6,028,372; 6,467,448;

6,561,151; 7,191,053; 7,483,783

Vehicle Security Patents:

5,467,070; 5,532,670; 5,534,845; 5,563,576;

5,646,591; 5,650,774; 5,673,017; 5,712,638;

5,872,519; 5,914,667; 5,952,933; 5,945,936;

5,990,786; 6,028,505; 6,452,484

Other patents pending.

8

Government Regulations

This device complies with Part 15 of FCC rules. Operation is subject

to the following two conditions: (1) This device may not cause harmful

interference, and (2) This device must accept any interference received,

including interference that may cause undesirable operation.

This equipment has been tested and found to comply with the limits for

a Class B digital device, pursuant to Part 15 of the FCC Rules. These

limits are designed to provide reasonable protection against harmful

interference in a residential installation. This equipment generates and

can radiate radio frequency energy and, if not installed and used in

accordance with the instruction manual, may cause harmful interference to

radio communications. However, there is no guarantee that interference will

not occur in a particular installation. If this equipment does cause harmful

interference to radio or television, which can be determined by turning

the equipment OFF and ON, the user is encouraged to try to correct the

interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.

• Increase the separation between the equipment and receiver.

• Connect the equipment into an outlet on a circuit different from that

to which the receiver is connected.

• Consult the dealer or an experienced radio / TV technician for help.

Remote Controls

To satisfy FCC RF exposure compliance requirements, this device should

be used in hand-held, hand operated configurations only. The device and

its antenna must maintain a separation distance of 20 cm or more from

the person’s body, except for the hand and wrists, to satisfy RF exposure

compliance. This device is designed to be used in a person’s hands and

its operating configurations do not support normal transmissions while it is

carried in pockets or holsters next to a person’s body.

Control Center

To satisfy FCC RF exposure compliance requirements, the device and

its antenna must maintain a separation distance of 20 cm or more from

the person’s body, except for the hand and wrists, to satisfy RF exposure

compliance.

9

This device complies with the Industry Canada Radio Standards

Specification RSS 210. Its use is authorized only on a no-interference,

no-protection basis; in other words, this device must not be used if it is

determined that it causes harmful interference to services authorized by

IC. In addition, the user of this device must accept any radio interference

that may be received, even if this interference could affect the operation

of the device.

WARNING!

Changes or modifications not expressly approved by the

party responsible for compliance could void the user’s authority to operate

this device.

10

Warning! Safety First

Please read the safety warnings below before proceed-

ing. Improper use of the product may be dangerous

or illegal.

Installation

Due to the complexity of this system, installation of this product must only be

performed by an authorized Directed dealer. If you have any questions, ask

your retailer or contact Directed directly at 1-800-753-0600.

Remote Start Capable

When properly installed, this system can start the vehicle via a command

signal from the remote control transmitter. Therefore, never operate the

system in an enclosed area or partially enclosed area without ventilation

(such as a garage). When parking in an enclosed or partially enclosed

area or when having the vehicle serviced, the remote start system must be

disabled using the “Start Valet” procedure found under “Valet Modes” in

this guide. It is the user’s sole responsibility to properly handle and keep

out of reach from children all remote control remote controls to assure

that the system does not unintentionally remote start the vehicle. IT IS

RECOMMENDED THAT THE USER INSTALL A CARBON MONOXIDE

DETECTOR IN THE LIVING AREAS ADJACENT TO THE VEHICLE. ALL

DOORS LEADING FROM ADJACENT LIVING AREAS TO THE ENCLOSED

OR PARTIALLY ENCLOSED VEHICLE STORAGE AREA MUST BE CLOSED

AT ALL TIMES. These precautions are the sole responsibility of the user.

Manual Transmission Vehicles

Remote starters on manual transmission vehicles operate differently than

those with automatic transmission because you must leave your car in

neutral. You must read this Owner’s Guide to familiarize yourself with

the proper procedures regarding manual transmission remote starters. If

you have any questions, ask your authorized Directed dealer or contact

Directed at 1-800-753-0600.

11

Before remote starting a manual transmission vehicle, be sure to:

• Leave the vehicle in neutral and be sure no one is standing in front

or behind the vehicle.

• Only remote start on a flat surface

• Have the parking brake fully engaged

WARNING!

It is the responsibility of the owner to ensure the parking/

emergency brake properly functions. Failure to do so can result in personal

injury or property damage. We recommend the owner have the parking /

emergency brake system inspected and adjusted by a qualified automotive

shop biannually.

Use of this product in a manner contrary to its intended mode of operation

may result in property damage, personal injury, or death. (1) Never

remotely start the vehicle with the vehicle in gear, and (2) Never remotely

start the vehicle with the keys in the ignition. The user must also have

the neutral safety feature of the vehicle periodically checked, wherein the

vehicle must not remotely start while the car is in gear. This testing should be

performed by an authorized Directed dealer in accordance with the Safety

Check outlined in the product installation guide. If the vehicle starts in gear,

cease remote start operation immediately and consult with the authorized

Directed dealer to fix the problem.

After the remote start module has been installed, contact your authorized

dealer to have him or her test the remote start module by performing the

Safety Check outlined in the product installation guide. If the vehicle starts

when performing the Neutral Safety Shutdown Circuit test, the remote

start unit has not been properly installed. The remote start module must be

removed or the installer must properly reinstall the remote start system so that

the vehicle does not start in gear. All installations must be performed by an

authorized Directed dealer.

OPERATION OF THE REMOTE START MODULE IF THE VEHICLE STARTS

IN GEAR IS CONTRARY TO ITS INTENDED MODE OF OPERATION.

OPERATING THE REMOTE START SYSTEM UNDER THESE CONDITIONS

MAY CAUSE THE VEHICLE TO UNEXPECTEDLY LUNGE FORWARD

RESULTING IN PROPERTY DAMAGE OR SERIOUS PERSONAL INJURY

INCLUDING DEATH. YOU MUST IMMEDIATELY CEASE THE USE OF

12

THE UNIT AND SEEK THE ASSISTANCE OF AN AUTHORIZED DIRECTED

DEALER TO REPAIR OR DISCONNECT THE INSTALLED REMOTE START

MODULE. DIRECTED WILL NOT BE HELD RESPONSIBLE OR PAY FOR

INSTALLATION OR REINSTALLATION COSTS.

This product is designed for fuel injected vehicles only. Use of this product in

a standard transmission vehicle must be in strict accordance with this guide.

This product should not be installed in any convertible vehicles, soft or

hard top with a manual transmission. Installation in such vehicles may pose

certain risk.

Interference

All radio devices are subject to interference which could affect proper

performance.

Upgrades

Any upgrades to this product must be performed by an authorized Directed

dealer. Do not attempt to perform any unauthorized modifications to this

product.

Water/Heat Resistance

This product is not designed to be water and/or heat-resistant. Please take

care to keep this product dry and away from heat sources. Any damage

from water or heat will void the warranty.

13

Limited Lifetime Consumer Warranty

Directed Electronics. (“Directed”) promises to the original purchaser to

repair or replace (at Directed’s election) with a comparable reconditioned

model any Directed unit (hereafter the “unit”), excluding without limitation

the siren, the remote transmitters, the associated sensors and accessories,

which proves to be defective in workmanship or material under reasonable

use during the lifetime of the vehicle provided the following conditions

are met: the unit was purchased from an authorized Directed dealer, the

unit was professionally installed and serviced by an authorized Directed

dealer; the unit will be profession¬ally reinstalled in the vehicle in which

it was originally installed by an authorized Directed dealer; and the unit

is returned to Directed, shipping prepaid with a legible copy of the bill of

sale or other dated proof of purchase bearing the following information:

consumer’s name, telephone number and address; the authorized dealers

name, telephone number and address; complete product description,

including accessories; the year, make and model of the vehicle; vehicle

license number and vehicle identification number. All components other

than the unit, including without limitation the siren, the remote transmitters

and the associated sensors and accessories, carry a one-year warranty

from the date of purchase of the same. ALL PRODUCTS RECEIVED BY

DIRECTED FOR WARRANTY REPAIR WITHOUT PROOF OF PURCHASE

FROM AN AUTHORIZED DEALER WILL BE DENIED. This warranty is

non-transferable and is automatically void if: the unit’s date code or serial

number is defaced, missing or altered; the unit has been modified or used

in a manner contrary to its intended purpose; the unit has been damaged

by accident, unreasonable use, neglect, improper service, installation or

other causes not arising out of defects in materials or construction. The

warranty does not cover damage to the unit caused by installation or

removal of the unit. Directed, in its sole discretion, will determine what

constitutes excessive damage and may refuse the return of any unit with

excessive damage.

TO THE MAXIMUM EXTENT ALLOWED BY LAW, ALL WARRANTIES,

INCLUDING BUT NOT LIMITED TO EXPRESS WARRANTY, IMPLIED

WARRANTY, WARRANTY OF MERCHANTABILITY, FITNESS FOR

PARTICULAR PURPOSE AND WARRANTY OF NON-INFRINGEMENT OF

INTELLECTUAL PROPERTY, ARE EXPRESSLY EXCLUDED; AND DIRECTED

NEITHER ASSUMES NOR AUTHORIZES ANY PERSON OR ENTITY TO

14

ASSUME FOR IT ANY DUTY, OBLIGATION OR LIABILITY IN CONNECTION

WITH ITS PRODUCTS. DIRECTED DISCLAIMS AND HAS ABSOLUTELY NO

LIABILITY FOR ANY AND ALL ACTS OF THIRD PARTIES INCLUDING ITS

AUTHORIZED DEALERS OR INSTALLERS. DIRECTED SECURITY SYSTEMS,

INCLUDING THIS UNIT, ARE DETERRENTS AGAINST POSSIBLE THEFT.

DIRECTED IS NOT OFFERING A GUARANTEE OR INSURANCE

AGAINST VANDALISM, DAMAGE OR THEFT OF THE AUTOMOBILE,

ITS PARTS OR CONTENTS; AND HEREBY EXPRESSLY DISCLAIMS ANY

LIABILITY WHATSOEVER, INCLUDING WITHOUT LIMITATION, LIABILITY

FOR THEFT, DAMAGE AND/OR VANDALISM. THIS WARRANTY DOES

NOT COVER LABOR COSTS FOR MAINTENANCE, REMOVAL OR

REINSTALLATION OF THE UNIT OR ANY CONSEQUENTIAL DAMAGES

OF ANY KIND. IN THE EVENT OF A CLAIM OR A DISPUTE INVOLVING

DIRECTED OR ITS SUBSIDIARY, THE VENUE SHALL BE SAN DIEGO

COUNTY IN THE STATE OF CALIFORNIA. CALIFORNIA STATE LAWS

AND APPLICABLE FEDERAL LAWS SHALL APPLY AND GOVERN THE

DISPUTE. THE MAXIMUM RECOVERY UNDER ANY CLAIM AGAINST

DIRECTED SHALL BE STRICTLY LIMITED TO THE AUTHORIZED DIRECTED

DEALER’S PURCHASE PRICE OF THE UNIT. DIRECTED SHALL NOT BE

RESPONSIBLE FOR ANY DAMAGES WHATSOEVER, INCLUDING BUT

NOT LIMITED TO, ANY CONSEQUENTIAL DAMAGES, INCIDENTAL

DAMAGES, DAMAGE TO VEHICLE, DAMAGES FOR THE LOSS OF TIME,

LOSS OF EARNINGS, COMMERCIAL LOSS, LOSS OF ECONOMIC

OPPORTUNITY AND THE LIKE. NOTWITHSTANDING THE ABOVE, THE

MANUFACTURER DOES OFFER A LIMITED WARRANTY TO REPLACE OR

REPAIR THE CONTROL MODULE SUBJECT TO THE CONDITIONS AS

DESCRIBED HEREIN. THIS WARRANTY IS VOID IF THE UNIT HAS NOT

BEEN PURCHASED FROM DIRECTED, OR AN AUTHORIZED DIRECTED

DEALER, OR IF THE UNIT HAS BEEN DAMAGED BY ACCIDENT,

UNREASONABLE USE, NEGLIGENCE, ACTS OF GOD, NEGLECT,

IMPROPER SERVICE, OR OTHER CAUSES NOT ARISING OUT OF

DEFECT IN MATERIALS OR CONSTRUCTION.

Some states do not allow limitations on how long an implied warranty will

last or the exclusion or limitation of incidental or consequential damages.

This warranty gives you specific legal rights and you may also have other

rights that vary from State to State.

This warranty is only valid for sale of product(s) within the United States

of America and in Canada. Product(s) sold outside of the United States of

America or Canada are sold “AS-IS” and shall have NO WARRANTY,

express or implied.

For further details relating to warranty information of Directed products,

please visit the support section of Directed’s website at: www.directed.com.

This product may be covered by a Guaranteed Protection Plan (“GPP”).

See your authorized Directed dealer for details of the plan or call Directed

Customer Service at 1-800-876-0800.

920-10011-01 2011-06

Télécommande à 1 bouton :

Unidirectionnelle 7616

Manuel d’utilisation

G7616VB 2017-08

FailSafe®, Learn Routine™, Silent Mode™, Valet® et Warn Away®

sont des marques commerciales ou des marques déposées appartenant à Directed®.

La page est en cours de chargement...

Viper DS4VB+ Le manuel du propriétaire

Viper DS4VB+ Le manuel du propriétaire

dans d''autres langues

Documents connexes

Autres documents