Risco watchout 312PR Installation Instructions Manual

Portuguese

Français

Español

Italiano

English

PIR Outdoor Detector

Rivelatore da Esterno ad Infrarosso Passivo

Detector de Exterior PIR

Détecteur IRP extérieur

Detector Infravermelho Passivo para área Externa

WatchOUT 312PR

Installation Instructions - Relay & BUS Modes

Istruzioni per l’installazione in modalità Relé e BUS

Instrucciones de Instalación - Modos Relé y BUS

Guide d'installation - Modes Relais et BUS

Instruções de Instalação - Modos Relé & BUS

2 WatchOUT PIR Installation Manual

WatchOUT PIR Installation Manual 3

English

Table of Contents

Relay Mode Installation 4

Introduction 4

Mounting 4

Mounting Considerations 4

Wall Mount Installation 6

Flat Mounting: 6

45° angle Mounting (Left side mounting) 6

Changing Back Tamper position 7

Terminal Wiring 7

DIP Switch Settings 8

Detection Range Adjustment 8

Walk test 9

LEDs Display 10

Relay Mode / Bus Mode Jumper 10

Optional Swivel Installation (Not Supplied) 10

Wall Mounting 10

Swivel Conduit Mounting

(using Conduit Metal Swivel Adaptor - CSMA, Figure 8, Detail A) 11

Replacing Lenses 12

Technical Specification 13

Ordering Information 13

Accessories Kits 13

BUS Mode Installation 14

Introduction 14

Terminal Wiring 14

Cover and Back Tamper 14

Cover Tamper Only 14

Cover Tamper to Zone Input 14

DIP Switch Settings 14

ProSYS Programming 15

4 WatchOUT PIR Installation Manual

Relay Mode Installation

Introduction

RISCO Group's WatchOUT 312PR, is a unique detector with signal processing based on two

Passive Infrared (PIR) channels. The detector has an adjustable detection range. The detector

can operate as a regular relay detector connected to any control panel, or as a BUS accessory

when connected to RISCO Group's ProSYS control panel via the RS485 BUS, thus having unique

remote control and diagnostic capabilities.

The following instructions describe the installation of the WatchOUT in Relay & BUS mode.

Mounting

Mounting Considerations

1. Installation Height: 0.8m - 1.2m

(2'8" – 3'11")

Typical Installation Height: 1m (3'3")

0.8m -1.2m

(2'8" - 3'11")

2. To ensure maximum operational reliability, install the detector perpendicular to the ground so

that the upper detection area is parallel to the ground.

ü

3. For optimum detection,

select a location that is likely

to intercept an intruder

moving across the coverage

pattern.

ü

4. Avoid pointing the detector to moving

objects (swaying trees, bushes etc.)

WatchOUT PIR Installation Manual 5

English

Installing the WatchOUT 312PR in challenging situations

In the following situations, rapid and significant infrared radiation changes can happen in both

PIR channels together, resulting in false alarms and therefore care should be taken.

1. Situations in which metal and/or glass objects measuring over 70cm (2‟4”) in height from the

ground are in the field of view of the detector (cars, metal gates, shutters, metal walls,

windows, etc.)

2. Situations in which a reflective surface on the ground larger than 1m (3‟4”) in diameter may

cause reflection into the detector‟s lens. Examples of a reflective surface on the ground are a

puddle, wet road or car park, smooth concrete or asphalt surface, swimming pool, etc.

Water Reflection

NOTES:

1. Please note that any outdoor PIR detector will require reduction in range to a shorter distance than the car,

metal object or surface reflection (so that these objects won‟t be protected) in order to eliminate false

alarms.

2. For full 15m (50’) coverage in the above situations, it is highly recommended to install the

WatchOUT DT, the only outdoor detector with 2 PIR channels and 2 Microwave channels.

3. WatchOUT detectors include high quality Silicon filters on the PIR sensors for blocking out white light

interferences. These filters are not intended to block infrared thermal radiation.

6 WatchOUT PIR Installation Manual

Wall Mount Installation

Note:

The installation knockouts numbering are marked on

the back plate.

1. Open WatchOUT front cover (unlock C1,

Figure 1).

2. Release internal base (unlock I1,

Figure 2).

3. Select mounting installation as follows:

Flat Mounting:

Open knockouts on external base (Figure 3).

 B1 - B4: Wall mounting knockouts

 T1: Back tamper knockout

 W2 / W3: wires entry knockouts

45° angle Mounting (Left side

mounting)

a. Open knockouts on external base

(Figure 3).

 L1, L2: Left mounting knockouts

 T3: Left tamper knockout

 W5 / W6: Wire entry knockouts

b. Remove tamper spring

c. Replace tamper bracket (Item 1) with

supplied flat tamper bracket (Item 2).

Item 1

Item 2

d. Insert Tamper lever B onto T5 and T3

and secure screw A (Figure 3)

4. Insert external wires through external base

W2, W3 (Flat Mounting) or W5, W6 (Left

side mounting)(Figure 3).

5. Secure external base to the wall.

6. Insert external wires and tamper wires

through internal base (Figure 4).

7. Secure internal base to external base (lock

I1, Figure 2).

8. Close the front cover (Lock C1, Figure 1)

after wiring and setting DIP switches.

9. Walk test the detector.

Figure 1

C1

Figure 2

I1

Figure 3

Tamper

Lever

A

T5

T1

B2

W9

B3

W2

L1

T3

B1

L2

W3

B4

R1

R2

T2

T6

(not visible)

T4

W5

W6

(not visible)

W7

W8

B

(not

visible)

(not

visible)

Figure 4

Note:

For 45° right side installation use the equivalent units on the external base as follows:

Knockouts Description

Left

Right

Mounting Knockouts

L1, L2

R1, R2

Tamper spring knockouts

T1,T3

T2,T4

Tamper screw anchor

T5

T6

Wiring Knockouts

W5, W6

W7, W8

WatchOUT PIR Installation Manual 7

English

Changing Back Tamper position

The back tamper is by default secured on the

right side of the internal base (Rear view). If

you wish to move it to the left side (rear view),

do the following (Figure 5):

1. Remove tamper screw 1 in order to

release the tamper from position 7.

2. Ensure tamper spring 2 rests over tamper

wire base 4.

3. Ensure plastic tamper bracket 3 rests over

both 2 and 4.

4. Secure tamper screw 1 into 3 over

position 6.

Figure 5

Left Side

Tamper

Right Side

Tamper

3

6

1

2

4

7

5

Notes:

a. Verify that you hear a "Click" when attaching the tamper spring to the wall.

b. For pole installation, the tamper can be moved to the bottom right-hand side of the internal base.

Terminal Wiring

12VDC

N.C N.C

+ -

LED

ENABL

ALARM

FREE

N.O COM

GRN

YEL

TAMPER

FREE

N.C

WatchOUT PIR - PCB

+,-

12 VDC

YELLOW

N/A (Used only for BUS mode installation)

GREEN

N/A (Used only for BUS mode installation)

ALARM

N.C relay, 24VDC , 0.1A

TAMPER

N.C relay, 24VDC , 0.1A

FREE

A free terminal that can be used to connect wires and EOL resistors

LED

ENABLE

Used to remotely control the LEDs when DIP1 is set to ON (used in high security

environments).

LED Enable: input is +12V OR no terminal connection.

LED Disable: Connect the input to 0V.

N.O

Programmable auxiliary relay terminals. This relay is used to activate auxiliary

units such as cameras or lighting when an alarm is triggered.

The operation of the auxiliary relay depends on the settings of DIP switches 4-7.

NORMAL

N.O

COM

N.C

ALARM

N.C

COM

N.O

COM

N.C

WatchOut 312PR - PCB

8 WatchOUT PIR Installation Manual

DIP Switch Settings

1 2 3 4 5 6 7 8

ON

Factory

Default

DIP 1: LEDs operation

On: LEDs enabled

Off: LEDs disabled

DIP 2-3: PIR Detection Sensitivity

Sensitivity

DIP2

DIP3

Low

Off

Mid

Off

On

Normal

On

Off

Maximum

On

DIP 4: Auxiliary relay control

ON: Enabled

OFF: Disabled

DIP 5: Used to define the auxiliary relay operation

following an alarm condition, depending on

Day/Night time (defined by 24 Hours / Night

Photocell)

ON (Night): Auxiliary relay is activated only

during nighttime.

OFF (24 Hours): Auxiliary relay is activated

24 hour

DIP 6-7: Defines the time duration that the auxiliary

relay is activated

Activation Time

Switch 6

Switch 7

2.2 seconds

OFF

2.0 Minutes

OFF

ON

4.0 Minutes

ON

OFF

8.0 Minutes

ON

DIP 8: Red LED /3 LED

ON: Red LED only

OFF: 3 LEDs

Detection Range Adjustment

Slide the moving PIR to the desired

position, see figure 6.

The range of the lower detection area

determines the detection range.

The upper PIR is fixed and its detection

area is parallel to the ground at all times.

The lower detection area changes from

2m to 12m depending on the location of

the moving PIR. Therefore, the detection

range is established according to the

location of the lower PIR since both the

upper and the lower PIR should be

triggered in order to activate an alarm.

Figure 6

WatchOUT PIR Installation Manual 9

English

Detection patterns (side view):

Detection range with 1m (3'3")

installation height:

POSITION

MAX.

DETECTION

LENGTH*

A

B

C

D

12m

(40')

7m

(23')

3m

(9'10")

2m

(6'6")

* NOTE:

Length may vary according to

environmental thermal conditions.

Walk test

Two minutes after applying power, walk test the protected area to verify proper operation.

Adjust the moving PIR for required detection range and reliability.

IMPORTANT!

Both upper and lower detection areas must be blocked simultaneously for detection to occur, see

figure 7 below.

NO DETECTION

DETECTION

Figure 7

10 WatchOUT PIR Installation Manual

LEDs Display

LED

State

Description

GREEN

Steady

Indicates upper PIR detection

YELLOW

Steady

Indicates moving PIR detection

RED

Steady

Indicates ALARM (Simultaneous 2 PIR channels)

Flashing

Indicates malfunctioned communication with ProSYS (BUS mode

only)

All LEDs

Flashing

(One after

another)

Unit initialization on power up

Notes:

1. DIP-Switch 1 should be in ON position to enable LED indications.

2. Only one LED is active at any one time. For example, in the case of both PIR channels detection, either the

steady yellow LED or the steady green LED is displayed (the first to detect), followed by the alarm red LED.

Relay Mode / Bus Mode Jumper

J-BUS jumper (located on the PCB between the red and

green LEDs) is used to define the detector’s mode of

operation as follows:

Relay

Mode

BUS Mode

O

N

O

N

Optional Swivel Installation (Not Supplied)

Please follow the instructions below for mounting the detector with the Standard Swivel:

1. Open WatchOUT front cover (Unlock C1, Figure 1).

2. Release internal base (Unlock I1, Figure 2).

3. Open knockouts on external base (Figure 8, Detail B)

 W1: Wires knockout

 S1,S2: Knockouts for securing external base to Standard Swivel

 S3: External base locking screw knockout

4. On the swivel accessory remove the required swivel cable wiring knockout S2, S7 or S9

(Figure 8, Detail A).

5. Remove back tamper from the internal base (see “Changing Back Tamper Position"

paragraph) and connect it to S5 (Figure 8, Detail A) on the Standard Swivel.

6. Select the mounting installation as follows:

Note:

Ensure that you see the engraved UP mark on the upper front face of the swivel.

Wall Mounting

a. Insert external cable wiring through knockouts S2, S7 or S9 and extract them (including the

tamper wires) through the Swivel Wires Passage (Figure 8, Detail B).

b. Secure swivel to the wall through holes S1, S3, S6 and S8.

WatchOUT PIR Installation Manual 11

English

Swivel Conduit Mounting (using Conduit Metal Swivel Adaptor - CSMA, Figure 8, Detail A)

S1

S2

S3

S9

S8

S7 S6

S5

S4

Tamper

(see Detail C)

Swivel Wires

Passage

Tamper

Spring

Holes

Ø 21 mm

Ø 16 mm

CSMA

M1

M2

M3

M4

Detail A Detail B

S1

W1

S2

S3

Snaps

Standard Swivel

Detail C

Figure 8

Note:

The CSMA is required when wiring is in a pipe external to the wall. It should be ordered separately P/N

RA300S.

a. Choose the direction upon which to mount the CSMA according to the required diameter:

16mm (0.63 inches) or 21mm (0.83 inches).

b. Insert conduit to the CSMA.

c. Secure CSMA to the wall through points (M1, M4).

d. Insert external cables and tamper wires from the conduit through the swivel wires passage

of the swivel (Figure 8, Detail A).

e. Secure swivel to the wall through holes S1, S3, S6 and S8.

Note:

The Tamper spring S5 (Figure 8) should make contact with the wall through the tamper spring holes M2 or

M3 on the CSMA. Make sure to hear the tamper "Click" when connecting to the wall.

7. Insert tamper wires and external cable wiring from Standard Swivel through knockout W1 on

the external base (Figure 8, Detail B).

8. Connect the external base to the swivel using the dedicated snaps (Figure 9).

External Base

Angle Locking

Screw

(See Note 2)

See Detail A

Swivel to External Base

Connecting Screws

Detail A

Swivel Assy

Connecting Screw

(See Note)

Snaps

S1

W1

S2

S3

Internal Base

PCB

Figure 9

12 WatchOUT PIR Installation Manual

NOTE:

Do not open or close the Swivel Assy Screw since it is used for connecting the swivel parts only.

9. Secure external base to swivel with two screws fastened to knockouts S1 and S2 (Figure 9).

10. Insert the supplied angle locking screw from the external base through the angle locking screw

knockout S3 on the external base to the standard swivel (Figure 9).

11. Rotate the Swivel to the desired position. Once the

Standard Swivel is in the desired position, secure

the angle locking screw.

IMPORTANT!

Take care not to tilt the detector upwards and

downwards. The detector should remain

perpendicular to the ground for maximum detection

and reliability.

12. Line up the internal base onto the external base.

Insert all wiring cables through the internal base.

13. Secure internal base to external base (Lock I1,

Figure 2).

14. To readjust the Standard Swivel when the PCB is

installed (Figure 10):

a. Bend down the black foam located below the

RED LED on the PCB (enough to reach the

Swivel locking screw).

b. Use a Philips screwdriver to release the

locking screw (see Figure 10).

c. Rotate the Swivel to the desired position.

d. Secure the angle locking screw.

Figure 10

NOTE:

When marks on the two movable parts are aligned (Figure 9), the Swivel is in 0 vertical /horizontal position.

Each click from this position represents shifting of 5 in vertical / horizontal position.

15. Close the front cover (Lock C1, Figure 1) and walk test the detector.

NOTE:

The screw has to pass through External Base and locked to the swivel.

Replacing Lenses

1. Unlock the six screws that hold the lens holding sleeve from the back of the front cover.

2. To release the protective sleeve, gently push the lens from the external side of the front cover.

3. Disconnect the lens from the sleeve by gently pushing the lens clips that secure it to the

sleeve.

4. Replace the lens. Place the 4 clips of the lens into the matching holes on the sleeve.

5. Insert the protective sleeve back into place on the front cover. Pay attention to place the

sleeve over the sealing rubber.

6. Secure the 6 holding screws back to their place.

WatchOUT PIR Installation Manual 13

English

Sleeve Locking

Screws

Lens Protecting

Sleeve

Holes for

Lens Clips

Lens Locking

Clips

Sealing Rubber

Front Cover

Locking Screw

Technical Specification

Electrical

Current consumption (Relay

Mode)

31mA at 12 VDC (Stand by)

44mA at 12 VDC (MAX with LED ON)

Current consumption (BUS

Mode)

34mA at 12 VDC (Stand by),

47mA at 12 VDC (Max. with LED ON)

Voltage requirements

9 -16 VDC

Alarm contacts

24 VDC, 0.1A

Auxiliary Relay

30 VDC, 1A

Physical

Size (including hood)

LxWxD

220 x 115 x 123mm (8.7 x 4.5 x 4.85 in.)

Environmental

Operating/Storage temperature

-30°C to 60°C (-22°F to 140°F)

* PIR technology is limited in rough environmental conditions.

Ordering Information

Model

Description

WatchOUT 312PR

WatchOUT PIR

Accessories Kits

Model

Description

Weight

RA300S

RA300P

Standard Swivel Kit

WatchOut Pole Adaptor Kit

0.21 Kg (0.46 lb)

0.25 Kg (0.55 lb)

14 WatchOUT PIR Installation Manual

BUS Mode Installation

Introduction

The information in this section relates to WatchOUT 312PR installation in BUS Mode only. Up to

32 bus detectors can be installed on the ProSYS RS485 bus, saving cabling time and enabling

remote control and diagnostics.

Terminal Wiring

+,-

Used for the connection of 12VDC power supply. Connect the (+) terminal to

the AUX RED and the (–) terminal to the COM BLK of the ProSYS terminals

YELLOW

Used for data communication with the ProSYS. Connect to the terminal to the

BUS YEL of the ProSYS

GREEN

Used for data communication with the ProSYS. Connect to the terminal to the

BUS GRN of the ProSYS

TAMPER

Used for the wiring for tamper detection, see below

LED

ENABLE

Used for the wiring for tamper detection, see below

Cover and Back Tamper

+

-

LED

ENABL

ALARM

FREE

N.O COM

GRN

YEL

TAMPER

FREE

N.C

COM

BLK

BUS

GRN

YEL

BUS Mode:

Cover + Back tamper wiring

BACK

TAMPER (N.C)

ProSYS

Short

AUX

RED

Cover Tamper Only

+

-

LED

ENABL

ALARM

FREE

N.O COM

GRN

YEL

TAMPER

FREE

N.C

COM

BLK

BUS

GRN

YEL

BUS Mode:

Cover Tamper Wiring

ProSYS

Short

AUX

RED

Cover Tamper to Zone Input

COM

BLK

BUS

GRN

YEL

BUS Mode:

Cover Tamper to Zone Input

ProSYS

BUS

Short

COM

Z1 Z2

Zone

Input

AUX

RED

+ -

LED

ENABL

ALARM

FREE

N.O COM

GRN

YEL

TAMPER

FREE

N.C

DIP Switch Settings

DIP Switch

Number

Description

1 - 5

Used to set the detector ID number. (See Table 1) Set the ID number in the

same way as for any other ProSYS accessory (Refer to the ProSYS installation

instruction manual)

6 - 8

Not used

WatchOUT PIR Installation Manual 15

English

WatchOUT ID: DIP Switches 1 - 5

ID

1

2

3

4

5

ID

1

2

3

4

5

01

OFF

17

OFF

ON

02

ON

OFF

18

ON

OFF

ON

03

OFF

ON

OFF

19

OFF

ON

OFF

ON

04

ON

OFF

20

ON

OFF

ON

05

OFF

ON

OFF

21

OFF

ON

OFF

ON

06

ON

OFF

ON

OFF

22

ON

OFF

ON

OFF

ON

07

OFF

ON

OFF

23

OFF

ON

OFF

ON

08

ON

OFF

24

ON

OFF

ON

09

OFF

ON

OFF

25

OFF

ON

10

ON

OFF

ON

OFF

26

ON

OFF

ON

11

OFF

ON

OFF

ON

OFF

27

OFF

ON

OFF

ON

12

ON

OFF

ON

OFF

28

ON

OFF

ON

13

OFF

ON

OFF

29

OFF

ON

14

ON

OFF

ON

OFF

30

ON

OFF

ON

15

OFF

ON

OFF

31

OFF

ON

16

ON

OFF

32

ON

ProSYS Programming

The following section describes the additional software programming options, added to the

ProSYS software, that concern the settings of the Without PIR as a BUS detector. Up to 32 BUS

detectors can be added to the system (16 in ProSYS 16) and each of them comes at the expense

of a zone in the system.

It is recommend reading and fully understanding the ProSYS Installation and User Manuals,

before programming the WatchOUT.

Notes:

The WatchOUT is compatible with the ProSYS software Version 4.xx and above.

The WatchOUT can be programmed via the U/D Software from UD Version 1.8 and above.

For maximum operation stability, it is best NOT to exceed a total of 300 meters (1000 feet) of wiring when

connecting the WatchOUT to the BUS

The WatchOUT is part of a new accessory category, BUS zones. Therefore, Adding/Deleting the

WatchOUT is identical to any other accessory with the following exception:

Each BUS Zone Detector should be assigned to a Regular Zone.

Any BUS detector can be assigned to a physical wired zone or to a virtual zone.

Physical zone: Any zone on the ProSYS PCB (zones 1-8) or on a wired zone expander

(ZE08, ZE16).

Virtual zone: Any zone on a BUS zone expander defined as BZ08 or BZ16.

Notes:

Virtual BUS zones are cost effective. They enable to expand your system zones without adding physical zone

expanders.

The virtual BUS zone expander can be used only for BUS zone detectors.

To add a BUS zone expander select type BZ08 or BZ16 when adding a zone expander (Quick key [7][1][2])

To Add / Delete the WatchOUT 312PIR

1. From the installer menu enter the Add/Delete menu: Quick Key [7][1][9][5] for BUS Zones

detectors

2. Use the / or / keys to position the cursor over the Bus Zone

ID number for which you want to assign (or delete) a detector.

Note:

Make sure that the detector's physical ID number is identical to the ID number you select

during programming

3. Place the cursor on the TYPE field and use the / key to select OPR12 for the

WatchOUT 312PIR detector.

16 WatchOUT PIR Installation Manual

4. Press / to confirm.

5. Repeat the process for the other BUS detectors.

Assigning the WatchOUT 312PIR to a Zone

1. From the main installer menu enter Zones: One by One option (Quick key [2][1])

2. Select the zone number that you want to assign the BUS detector.

Note:

If you defined a BUS Zone Expander select a zone number from the virtual zones (defined

by the BUS zone expander).

3. Define Partitions, Groups, Zone Type and Zone Sound.

4. In the Termination category select [5] Bus Zone followed by / . The

following display appears:

Z:001 LINK TO:

ID:01 TYPE:OPR12

Z:001 LINK TO:

ID:01 TYPE:OPR12

5. Select the BUS zone number to assign to the programmed zone. The type field will be

updated automatically when selecting the BUS zone.

6. Press / . The loop response category is not applicable to a BUS zone and

the following display appears:

Z:001 RESPONSE:

N/A-BUS ZONE

Z:001 RESPONSE:

N/A-BUS ZONE

7. Press / , assign label and press /

Configuring the WatchOUT 312PIR Parameters

1. To access the WatchOUT settings option press [2][0][3] from the main installer menu.

The following display appears:

B-ZONE PRMS:

ZONE#=001 (M:ZZ)

B-ZONE PRMS:

ZONE#=001 (M:ZZ)

2. Select the zone that the BUS zone was assigned to and press / . You can

now program the WatchOUT parameters as follows:

Zones Miscellaneous: BUS Zone

Quick Keys

Parameter

Default

[2][0][3][zzz]

[1]

LEDS

3 LEDS

Defines the LEDS operation mode

[2][0][3][zzz]

[1][1]

Off

Disables the LEDS operation

[2][0][3][zzz]

[1][2]

Red Only

Only the Red led will operate. This option is highly recommended to avoid

the possibility that the intruder will “Learn” the detector behavior.

[2][0][3][zzz]

[1][3]

3 LEDS

All 3 LEDs will operate

[2][0][3][zzz]

[2]

PIR Sensitivity

Normal

Defines the PIR sensitivity of the detector

[2][0][3][zz]

[2][1]..[4]

Sensitivity Options

WatchOUT PIR Installation Manual 17

English

Zones Miscellaneous: BUS Zone

Quick Keys

Parameter

Default

1) Low

2) Medium

3) Normal

4) High

[2][0][3][zzz]

[3]

Lens Type

Wide Angle

Defines the actual Lens of the detector

[2][0][3][zzz]

[3][1]..[2]

Lens Type Options

1) Wide Angle 2) Barrier / Long Range

[2][0][3][zzz]

[4]

Auxiliary Relay Mode

No

Defines the operation of the Auxiliary relay of the detector

[2][0][3][zzz]

[4][1]

Off

Auxiliary relay is disabled

[2][0][3][zzz]

[4][2]

24 Hours

The Auxiliary Relay will always follow an alarm

[2][0][3][zzz]

[4][3]

Night Only

The auxiliary relay output will follow an alarm condition only during night time.

The time defined by the photocell on the PCB.

[2][0][3][zzz]

[5]

Auxiliary Relay Time

2.2 seconds

Defines the time duration that the auxiliary relay is activated

[2][0][3][zzz]

[5][1]..4]

Auxiliary Relay Time Options

1) 2.2 seconds

2) 2 minutes

3) 4 minutes

4) 8 minutes

Diagnostics

The ProSYS enables you to test parameters that reflect the operation of the detector.

1. From the main user menu press [4] to access the Maintenance menu.

2. Enter the Installer code (or sub-installer) and press / .

3. Press [9] [1] to for the Bus Zones diagnostic menu.

4. Enter the digit of the zone that you want to test and then press / . The

system will perform the diagnostics test and a list of test parameters will appear, as

indicated in the table below.

5. Use the keys / / to view the diagnostics test results

User Menu: 4) Maintenance  9) Diagnostic  1) Bus Zone

Quick Keys

Parameter

[4][9][1][zzz]

Detector Input Voltage: Display the input voltage of the detector.

PIR 1 Level: Displays PIR channel 1 DC level. Range 0.1v - 4v

PIR 1 Noise Level: Displays PIR channel 1 AC level. Range 0VAC

(No noise) - 4VA

PIR 2 Level: Displays PIR channel 1 DC level. Range 0.1v - 4v

PIR 2 Noise Level: Displays PIR channel 2 AC level. Range 0VAC

(No noise) - 4VA

18 Manuale di installazione WatchOUT PIR

INDICE DEI CONTENUTI

Installazione in modalità relé 19

Introduzione 19

Installazione 19

Considerazioni per l’installazione 19

Installazione a parete 21

Installazione piana: 21

Installazione angolare di 45° (installazione a sinistra) 21

Modifica della posizione del tamper antirimozione 22

Cablaggio Morsettiera 22

Predisposizione microinterruttori 23

Regolazione area di copertura 23

Prova di movimento 24

Indicatori LED 25

Microinterruttore Modalità Relé / Bus 25

Installazione dello Snodo Standard 25

Installazione a parete 25

Installazione per tubo elettrico 26

Sostituzione delle Lenti 28

Caratteristiche Tecniche 29

Informazioni per l’ordine 29

Kit Accessori 29

Installazione in modalità BUS 30

Introduzione 30

Cablaggio morsettiera 30

Tamper Antiapertura e Antirimozione 30

Solo Tamper Antiapertura 30

Tamper Antiapertura ad un Ingresso di Zona 30

Predisposizione Microinterruttori 30

Programmazione ProSYS 31

Manuale di installazione WatchOUT PIR 19

Italiano

Installazione in modalità relé

Introduzione

Il rivelatore da esterno ad infrarosso passivo WatchOUT di RISCO, è un dispositivo a

microprocessore che elabora i segnali rilevati tramite due canali all’infrarosso passivo (PIR). Il

WLT312 ha un‟area di copertura regolabile. Il rivelatore può funzionare come rivelatore

tradizionale con uscite a relé collegabili a qualsiasi centrale d’allarme, o come rivelatore

indirizzato via BUS 485 collegato ai sistemi ProSYS di RISCO. Quando viene collegato ai sistemi

ProSYS, il rivelatore può essere programmato e testato sia localmente che in remoto tramite

tastiere LCD ProSYS e/o software di Teleassistenza.

Le istruzioni che seguono descrivono l’installazione e la configurazione del WatchOUT sia in

modalità Relé che via BUS. Per informazioni sul collegamento in modalità BUS ProSYS,

consultare il capitolo il capitolo “Installazione in modalità BUS”.

Installazione

Considerazioni per l’installazione

1. Altezza possibile: da 0.8m a 1.2m

Altezza tipica: 1m

Angolo di copertura: 90°

0.8m -1.2m

(2'8" - 3'11")

2. Per ottenere la migliore condizione di funzionamento ed affidabilità, installare il rivelatore

perpendicolare al terreno in modo che la zona di rilevazione superiore sia parallela al terreno.

3. Per una migliore rivelazione

selezionare una posizione

di installazione in modo che

l‟eventuale intruso attraversi

l‟area di copertura.

ü

4. Evitare di direzionare l‟unità verso oggetti in

movimento (alberi ondeggianti, cespugli, ecc.)

20 Manuale di installazione WatchOUT PIR

Installazione del WatchOUT 312PR in situazioni critiche:

Nelle seguenti situazioni variazioni delle radiazioni all‟infrarosso rapide e rilevanti possono far si

che entrambi i canali PIR si attivino contemporaneamente, con conseguenti falsi allarmi.

1. Situazioni in cui oggetti riflettenti di vetro e/o metallo di dimensioni superiori ai 70 cm di

altezza da terra siano nel campo visivo del rivelatore (automobili, cancelli metallici,

saracinesche, muri metallici, finestre, etc.).

2. Situazioni in cui una superficie riflettente a terra con un diametro maggiore di 1m possa

causare un riflesso nelle lenti del rivelatore. Per esempio una piscina, una pozzanghera, la

strada bagnata, asfalto o cemento molto liscio.

Riflesso dell‟acqua

NOTE:

a. Si noti che qualsiasi rivelatore PIR da esterno, per evitare falsi allarmi, richiede una riduzione di portata al

fine di evitare di proteggere superfici riflettenti come auto, oggetti metallici o pozzanghere.

b. Per ottenere una copertura completa a 15m nelle installazioni sopra descritte, si raccomanda di

installare il WatchOUT DT, l’unico rivelatore da esterno con 2 canali PIR e 2 canali a microonde.

c. I rivelatori WatchOUT includono sui sensori PIR dei filtri al silicone di elevata qualità per filtrare le

interferenze causate dalle luci bianche. Questi filtri non bloccano le radiazioni termiche ad infrarossi

necessarie per rilevazione degli intrusi.

La page charge ...

Risco watchout 312PR Installation Instructions Manual

Risco watchout 312PR Installation Instructions Manual

dans d''autres langues

Documents connexes

Autres documents