3com Baseline 2016 Manuel utilisateur

Marque: 3com

Modèle: Baseline 2016

Catégorie: Commutateurs réseau

Taper: Manuel utilisateur

Ce manuel convient également à

Baseline 2024

The 3Com

Baseline Switch 2016/2024 is a versatile, easy-to-use

unmanaged switch. It is ideal for users who want the high-speed

performance of 10/100 switching but do not need sophisticated

management capabilities. The Baseline 10/100 Switch is shipped

ready for use. No configuration is necessary.

The Switch has 16 or 24 shielded RJ-45, 10/100 Mbps

auto-negotiating ports on the front panel. Each port automatically

determines the speed and duplex mode of the connected

equipment and provides a suitable switched connection. Each port

also supports automatic MDI/MDI-X detection.

The Switch is suited for office use where it can be free standing,

or rack mounted (in a wiring closet or equipment room).

The Switch comes with:

 One power cord for use with the Switch

 Four self-adhesive rubber pads

 One mounting kit

The Switch is powered from the AC mains supply.

The Switch provides high performance switched connections to

10 Mbps and 100 Mbps hubs, servers and workstations that

require a dedicated switched link.

The diagram opposite shows an example configuration:

INTRODUCTION

Endstations on shared

100 Mbps connections

Baseline Dual Speed Hub

10/100Mbps link

Endstations on switched

10/100 Mbps connections

Baseline Switch 2024

3Com

Baseline Switch 2016 and 2024 User Guide

3C16470B/3C16471B

Part No. 10016425 Rev. AA

Bas

elin

e Swit

ch 2024

Numbered elements in this diagram refer to numbered sections in

the text. A 24-port unit is shown.

Front Panel

1 24 RJ-45 10/100 Ports

WARNING

: RJ-45 ports. These are shielded RJ-45 data

sockets. They cannot be used as standard traditional

telephone sockets, or to connect the unit to a traditional

PBX or public telephone network. Only connect RJ-45

data connectors, network telephony systems, or network

telephones to these sockets. Either shielded or unshielded

data cables with shielded or unshielded jacks can be

connected to these data sockets.

AVERTISSEMENT: Les ports RJ-45. Ceux-ci sont

protégés par des prises de données. Ils ne peuvent pas

être utilisés comme prises de téléphone conventionnelles

standard, ni pour la connection de l’unité à un réseau

téléphonique central privé ou public. Raccorder seulement

connecteurs de données RJ-45, systèmes de réseaux de

téléphonie ou téléphones de réseaux à ces prises. Il est

possible de raccorder des câbles protégés ou non

protégés avec des jacks protégés ou non protégés à ces

prises de don.

WARNUNG: RJ-45-Porte. Diese Steckdose sind

geschützte Datensteckdosen. Sie dürfen weder wie

normale traditionelle Telefonsteckdosen noch für die

Verbindung der Einheit mit einem traditionellem privatem

oder öffentlichem Telefonnetzwerk gebraucht werden.

Nur RJ-45-Datenanscluße, Telefonnetzsysteme or

Netztelefone an diese Steckdosen anschließen. Entweder

geschützte oder ungeschützte Buchsen dürfen an diese

Datensteckdosen angeschlossen werden.

ADVERTENCIA: puertos RJ-45. Son conectores de datos

RJ-45 blindados. No pueden utilizarse como tomas de

teléfono tradicionales estándar ni para conectar la unidad

a una central de conmutación PBX tradicional ni a una

red telefónica pública. Conecte sólo conectores de datos

RJ-45, sistemas de telefonía de red local o teléfonos de

red local a estas tomas. Es posible conectar cables de

datos blindados o sin blindar con clavijas blindadas o sin

blindar a estos conectores de datos.

10BASE-T/100BASE-TX Ports

The Switch has 16 (3C16470B) or 24 (3C16471B) 10/100 Mbps

auto-negotiating ports. To connect a device to the Switch, use

Category 5 unshielded or shielded (screened) 100 Ohm TP cable

(or Category 3 cable for a 10 Mbps connection). The maximum

length of cable for each connection is 100m (328ft). Connect one

end of the cable to an RJ-45 port on the Switch, and the other

end to the appropriate RJ-45 port on the connecting device.

Each port on the Switch is auto-negotiating: its speed and duplex

mode (half duplex or full duplex) are automatically determined by

the capabilities of the connected device.

Each port supports automatic MDI/MDI-X detection and can be

connected to either a 10BASE-T or a 100BASE-TX device.

If you connect two Switch units together, the link

between them operates at 100 Mbps full duplex. You

must use Category 5 cable when connecting the units.

CAUTION: The Switch supports full duplex auto-negotia-

tion. If the connected device does not support auto-nego-

tiation, the Switch will operate in half duplex mode (even

if the device is operating in full duplex mode). In such a

configuration, you may notice some degradation of net-

work performance. 3Com recommends that you use

devices that are capable of auto-negotiation (and that

you ensure that auto-negotiation is enabled, if it is a con-

figurable option).

Activity/Link/Speed Status LEDs

The first (top) and third row of LEDs, which are colored yellow or

green, show the activity and speed status of the related ports:

3 Duplex Status LEDs

The second and fourth (bottom) row of Status LEDs, which are

colored yellow, show the duplex status of the related ports:

HOW TO USE THE 2016/2024 SWITCH

21 24

Baseline Switch 2024

Status Meaning

On The link has been established.

Flashing Packets are being received or transmitted on the port.

Off If the link has not been established, either nothing is

connected to the port, or there is a problem:

■ Check that the attached device is powered on.

■ Check that the cable is the correct type and is not faulty.

If these checks do not identify the cause of the problem, it

may be that the unit or the device connected to the port is

faulty. Contact your supplier for further advice.

Green The link is operating at 100 Mbps.

Yell ow The link is operating at 10 Mbps.

Status Meaning

On Yellow The port is operating in full-duplex mode.

Off The port is operating in half-duplex mode.

4 Power LED

The Power LED shows the power status of the Switch:

Self-adhesive Pads

The unit is supplied with four self-adhesive rubber pads.

You do not need to apply the pads if you intend to rack

mount the unit.

If the unit is to be part of a free standing stack, apply the pads to

each marked corner area on the underside of the unit. Place the

unit on top of the lower unit, ensuring that the pads locate with

the recesses of the lower unit.

Rear Panel Connections

6 Power Supply

The Switch automatically adjusts to the supply voltage. Only use

the power cord that is supplied with the Switch.

Positioning the Switch

CAUTION: If installing the Switch in a stack of different

size Baseline units, the smaller units must be installed

above the larger ones. Do not have a free-standing stack

of more than six units.

CAUTION: Please read the following safety information

carefully before installing the Switch.

AVERTISSEMENT: Veuillez lire à fond l'information de la

sécurité suivante avant d'installer le Switch.

WARNUNG: Bitte unbedingt vor dem Einbauen des

Switches die folgenden Sicherheitsanweisungen durchle-

sen.

ATTENZIONE: Vi preghiamo prima di leggere con attenzi-

one tutte le informazioni concernenti l'installazione

dell'interruttore.

When deciding where to position the Switch ensure that:

 It is accessible and cables can be connected easily.

 Cabling is away from sources of electrical noise such as

radios, transmitters and broadband amplifiers, and away from

power lines and fluorescent lighting fixtures.

 The Switch is situated away from sources of electrically

conductive dust, for example laser printers.

 The AC supply used by the Switch is separate to those used

by units that generate high levels of AC noise, for example air

conditioning units and laser printers.

 Water or moisture cannot enter the case of the unit.

 Air flow around the unit and through the vents in the side of

the case is not restricted (3Com recommends that you

provide a minimum of 25 mm (1 in.) clearance).

To prolong the operational life of your units:

 Never stack units more than six high if free-standing, and

ensure that cables are supported so that they do not cause

the stack to fall over.

 Do not place objects on top of any unit or stack.

 Do not obstruct any vents at the sides of the case.

Rack Mounting

The Switch can be mounted in a 19-inch equipment rack using

the Mounting Kit. Refer to “Mounting Kit Instructions” on

page 5.

Power Up

Use the following sequence to power up the Switch:

1 Check the network connections and cables.

2 Connect the power supply cable to the appropriate power

socket on the rear panel of the unit; refer to 6 Power

Supply

3 Connect the plug to the power supply outlet socket and

switch on the power supply at the socket.

When the switch is powered on, the Power LED should be lit on

green. If it is not, refer to 4 Power LED.

Spot Checks

At frequent intervals you should visually check the Switch. Regular

checks can give you an early warning of a possible failure; any

problems can then be attended to when there will be least effect

on users. Check that all external cabling connections are secure

and that no cables are pulled taut.

If you experience any problems operating the Switch, refer to “Prob-

lem Solving” on page 3.

Refer to the information about LEDs given earlier in this guide to

see if the problem can be identified and rectified. Here are some

common problems that can occur:

Link Status LED not lit for a port that has a connection.

There is a problem with this connection. Check that:

 The device being connected to is powered on and operating

correctly.

 The cable is connected at both ends.

 The cable is not damaged.

 If the connection is to a workstation, that the workstation’s

network interface is installed and configured correctly.

All ports appear to show continual activity. There may be

broadcast storms on the network.

Remove port connections one at a time, waiting a few seconds

between each port. If the LEDs go off after disconnection, the

device that was connected to that port is introducing an excessive

amount of broadcast frames to the network (some pieces of net-

work equipment operate by sending out broadcast frames regu-

larly). Refer to the documentation that accompanies the device for

information on disabling the broadcast operation.

If the problem persists and the unit still does not operate success-

fully, contact your supplier. Include the product number and serial

number (printed on a label supplied with the unit) as well as a

brief description of the fault.

Status Meaning

On Green The unit is powered on and ready for use.

Off The unit is not receiving power:

■ Check the power cord is connected correctly.

■ If the unit still does not operate, contact your supplier.

INSTALLING THE SWITCH

PROBLEM SOLVING

Please read the following safety information carefully before

installing the Switch.

WARNING: Installation and removal of the unit must be carried out

by qualified personnel only.

 If installing the Switch unit in a stack with other Baseline units, the

Switch must be installed below the narrower Hub units.

 The unit must be connected to an earthed (grounded) outlet to comply

with international safety standards.

 Do not connect the unit to an A.C. outlet (power supply) without an

earth (ground) connection.

 The appliance coupler (the connector to the unit and not the wall plug)

must have a configuration for mating with an EN60320/IEC320

appliance inlet.

 The socket outlet must be near to the unit and easily accessible. You

can only remove power from the unit by disconnecting the power cord

from the outlet.

 This unit operates under SELV (Safety Extra Low Voltage) conditions

according to IEC 60950-1. The conditions are only maintained if the

equipment to which it is connected also operates under SELV

conditions.

France and Peru only

This unit cannot be powered from IT (Impédance à la terre) supplies. If your supplies

are of IT type, this unit must be powered by 230V (2P+T) via an isolation

transformer ratio 1:1, with the secondary connection point labelled Neutral,

connected directly to earth (ground).

Power Cord Set

This must be approved for the country where it will be used. e.g.

Veuillez lire à fond l'information de la sécurité suivante avant

d'installer le Switch.

AVERTISSEMENT: L’installation et la dépose de ce groupe doivent

être confiés à un personnel qualifié.

 Si vous entassez l’unité Switch avec les unités Baseline, l’unité Switch

doit être installée en dessous des unités Hub plus étroites.

 Ne branchez pas votre appareil sur une prise secteur (alimentation

électrique) lorsqu'il n'y a pas de connexion de mise à la terre (mise à la

masse).

 Vous devez raccorder ce groupe à une sortie mise à la terre (mise à la

masse) afin de respecter les normes internationales de sécurité.

 Le coupleur d’appareil (le connecteur du groupe et non pas la prise

murale) doit respecter une configuration qui permet un branchement

sur une entrée d’appareil EN60320/IEC 320.

 La prise secteur doit se trouver à proximité de l’appareil et son accès

doit être facile. Vous ne pouvez mettre l’appareil hors circuit qu’en

débranchant son cordon électrique au niveau de cette prise.

 L’appareil fonctionne à une tension extrêmement basse de sécurité qui

est conforme à la norme IEC 60950-1. Ces conditions ne sont

maintenues que si l’équipement auquel il est raccordé fonctionne dans

les mêmes conditions.

France et Pérou uniquement:

Ce groupe ne peut pas être alimenté par un dispositif à impédance à la terre. Si vos

alimentations sont du type impédance à la terre, ce groupe doit être alimenté par

une tension de 230 V (2 P+T) par le biais d’un transformateur d’isolement à rapport

1:1, avec un point secondaire de connexion portant l’appellation Neutre et avec

raccordement direct à la terre (masse).

Cordon électrique

Il doit être agréé dans le pays d’utilisation.

Bitte unbedingt vor dem Einbauen des Switches die folgenden

Sicherheitsanweisungen durchlesen.

WARNUNG: Die Installation und der Ausbau des Geräts darf nur

durch Fachpersonal erfolgen.

 Wenn der Switch 2016/2024 mit anderen 3Com Hubs oder Switch

gestackt werden soll, müssen grössere Geräte unter den schmaleren

Hubs eingebaut werden.

 Das Gerät sollte nicht an eine Wechselstromsteckdose angeschlossen

werden.

 Das Gerät muß an eine geerdete Steckdose angeschlossen werden,

welche die internationalen Sicherheitsnormen erfüllt.

 Der Gerätestecker (der Anschluß an das Gerät, nicht der

Wandsteckdosenstecker) muß einen gemäß EN60320/IEC320

konfigurierten Geräteeingang haben.

 Die Netzsteckdose muß in der Nähe des Geräts und leicht zugänglich

sein. Die Stromversorgung des Geräts kann nur durch Herausziehen

des Gerätenetzkabels aus der Netzsteckdose unterbrochen werden.

 Der Betrieb dieses Geräts erfolgt unter den SELV-Bedingungen

(Sicherheitskleinstspannung) gemäß IEC 60950-1. Diese Bedingungen sind

nur gegeben, wenn auch die an das Gerät angeschlossenen Geräte unter

SELV-Bedingungen betrieben werden.

SAFETY INFORMATION

U.S.A. and

Canada

■ The cord set must be UL-approved and CSA certified.

■ The minimum specifications for the flexible cord are:

No. 18 AWG

Type SV or SJ

3-conductor

■ The cord set must have a rated current capacity of at least

10A.

■ The attachment plug must be an earth-grounding type

with a NEMA 5-15P (15 A, 125 V) or NEMA 6-15P (15 A,

250 V) configuration.

Denmark ■ The supply plug must comply with Section 107-2-D1,

Standard DK2-1a or DK2-5a.

Switzerland ■ The supply plug must comply with SEV/ASE 1011.

UK ■ The supply plug must comply with BS1363 (3-pin 13-amp)

and be fitted with a 5 A fuse which complies with

BS1362.

■ The mains cord must be <HAR> or <BASEC> marked and

be of type HO3VVF3GO.75 (minimum).

Europe ■ The supply plug must comply with CEE7/7 (“SCHUKO”)

■ The mains cord must be <HAR> or <BASEC> marked and

be of type HO3VVF3GO.75 (minimum).

L’INFORMATION DE SÉCURITÉ IMPORTANTE

Etats-Unis et

Canada:

■ Le cordon doit avoir reçu l’homologation des UL et un

certificat de la CSA.

■ Le cordon souple doit respecter, à titre minimum, les

spécifications suivantes:

calibre 18 AWG

type SV ou SJ

à 3 conducteurs

■ Le cordon doit être en mesure d’acheminer un courant

nominal d’au moins 10 A.

■ La prise femelle de branchement doit être du type à mise à la

terre (mise à la masse) et respecter la configuration NEMA

5-15P (15 A, 125 V) ou NEMA 6-15P (15 A, 250 V).

Danemark:

■ La prise mâle d’alimentation doit respecter la section 107-2 D1

de la norme DK2 1a ou DK2 5a.

Suisse:

■ La prise mâle d’alimentation doit respecter la norme SEV/ASE

1011.

Europe

■ La prise secteur doit être conforme aux normes CEE 7/7

(“SCHUKO”)

■ LE cordon secteur doit porter la mention <HAR> ou <BASEC>

et doit être de type HO3VVF3GO.75 (minimum).

WICHTIGE SICHERHEITSINFORMATIONEN

Stromkabel. Dies muss von dem Land, in dem es benutzt wird geprüft werden:

Schweiz

■ Dieser Stromstecker muß die SEV/ASE 1011Bestimmungen

einhalten.

Europe ■ Das Netzkabel muß vom Typ HO3VVF3GO.75

(Mindestanforderung) sein und die Aufschrift <HAR> oder

<BASEC> tragen.

■ Der Netzstecker muß die Norm CEE 7/7 erfüllen (”SCHUKO”).

Lea la sección ‘Información de seguridad importante’ detenida-

mente antes de instalar la unidad

ADVERTENCIA: La instalación y la extracción de la unidad sólo

debe llevarla a cabo personal cualificado.

 Si instala la unidad Switch en una pila con unidades Baseline, el Switch

se debe instalar debajo de las unidades Hub más estrechas.

 La unidad debe estar conectada a tierra para garantizar el

cumplimiento de las normas de seguridad.

 No conecte la unidad a una toma de CA (fuente de alimentación) sin

conexión a tierra.

 El acoplador del equipo (es decir, el conector para la unidad y no la

toma de la pared) debe tener una configuración que se adapte a una

entrada del equipo EN60320/IEC320.

 El enchufe debe estar cerca de la unidad y ser de fácil acceso. La única

forma de interrumpir la alimentación de la unidad es desconectando el

cable eléctrico de la toma de corriente.

 Esta unidad funciona en condiciones de voltaje extrabajo de seguridad

(SELV), de conformidad con la norma IEC 60950-1. Las condiciones de

funcionamiento sólo se mantendrán si el equipo al que esté conectada

la unidad también cumple los requisitos SELV.

Sólo para Francia y Perú.

Esta unidad no puede recibir corriente de fuentes IT

†

. Si las fuentes de

suministro de corriente son de tipo IT, esta unidad debe recibir 230 V (2P+T) a

través de un transformador aislador con relación 1:1, con el punto de

conexión secundario etiquetado como neutro conectado directamente a tierra.

†

Impédance à la terre

El cable eléctrico

Debe estar homologado para el país donde se utilice:

Introduction

The Switch is supplied with two mounting brackets and four

screws. These are used for rack-mounting the unit. When

mounting the unit, you should take note of the guidelines given

in “Positioning the Switch” on page 3.

Rack Mounting the Units

The Switch is 1U high and will fit a standard 19-inch rack.

CAUTION: Disconnect all cables from the unit before

continuing. Remove the self-adhesive pads from the

underside of unit, if already fitted.

1 Place the unit the right way up on a hard, flat surface with

the front facing towards you.

2 Locate a mounting bracket over the mounting holes on one

side of the unit (refer to the figure following step 6).

3 Insert the two screws supplied in the mounting kit and fully

tighten with a suitable screwdriver.

4 Repeat the two previous steps for the other side of the unit.

5 Insert the unit into the 19-inch rack and secure with suitable

screws (not provided).

6 Reconnect all cables.

Related Standards

The 3Com Baseline Switch 2016/2024 has been designed to the

following standards:

Environmental

Physical

Electrical

INFORMACION DE SEGURIDAD IMPORTANTÉ

Europa

■ La toma de alimentación debe cumplir la norma CEE

7/7 (“SCHUKO”).

■ El cable de la red eléctrica debe tener la marca <HAR>

o <BASEC> y ser de tipo H03VVF3g0.75 (mínimo).

MOUNTING KIT INSTRUCTIONS

TECHNICAL INFORMATION

Functional

ISO 8802-3, IEEE 802.3 (Ethernet), IEEE 802.3u (Fast

Ethernet), IEEE 802.3x (Flow Control), IEEE 802.3d

(Bridging)

Safety

UL 60950-1, EN60950-1, CSA 22.2 No. 60950-1, IEC

60950-1

EMC Emissions

EN 55022 Class A, FCC Part 15 Subpart B Class A,

ICES-003 Class A, VCCI Class A, AS/NZS CISPR 22 Class

Immunity

EN 55024

Operating Temperature

0–40 °C (32–104 °F)

Humidity

10–95% (non-condensing)

Width

440 mm (17.3 in.)

Depth

173 mm (6.8 in.)

Height

44 mm (1.7 in.) or 1U

Weight

2.6 kg (5.8 lb)

Mounting

Free standing, or 19 in. rack mounted using the

mounting kit supplied

Power Inlet

IEC 320

AC Line Frequency

50/60 Hz

Input Voltage

100–240 VAC

Current Rating

1 Amp (maximum)

Maximum Power

Consumption

3C16470B: 15 VA

3C16471B: 20 VA

Maximum Power

Dissipation

3C16470B: 52 BTU/hr

3C16471B: 68 BTU/hr

FCC Statement

This equipment has been tested and found to comply with the

limits for a Class A digital device, pursuant to part 15 of the FCC

rules. These limits are designed to provide reasonable protection

against harmful interference when the equipment is operated in

a commercial environment. This equipment generates, uses and

can radiate radio frequency energy and, if not installed and used

in accordance with the instructions, may cause harmful interfer-

ence to radio communications. Operation of this equipment in a

residential area is likely to cause harmful interference to radio

communications, in which case the user will be required to cor-

rect the interference at their own expense.

Information To The User

If this equipment does cause interference to radio or television

reception, which can be determined by turning the equipment

off and on, the user is encouraged to try to correct the interfer-

ence by one or more of the following measures:

 Reorient the receiving antenna.

 Relocate the equipment with respect to the receiver.

 Move the equipment away from the receiver.

 Plug the equipment into a different outlet so that equipment

and receiver are on different branch circuits.

If necessary, the user should consult the dealer or an experienced

radio/television technician for additional suggestions. The user

may find the following booklet prepared by the Federal Commu-

nications Commission helpful:

How to Identify and Resolve Radio-TV Interference Problems

This booklet is available from the U.S. Government Printing

Office, Washington, DC 20402, Stock No. 004-000-00345-4.

In order to meet FCC emissions limits, this equipment must be

used only with cables which comply with IEEE 802.3.

CE Statement (Europe)

This product complies with the European Low Voltage Directive

73/23/EEC and ETIC Directive 89/336/EEC as amended by

European Directive 93/68/EEC/.

European Declaration of Conformity

A signed copy of the European Declaration of Conformity for the

Baseline Switch 2016 & 2024 can be downloaded from:

http://support.3com.com/doc/3C1647xB_EU_DoC.pdf

CSA Statement

This Class A digital apparatus meets all requirements of the

Canadian Interference-Causing Equipment Regulations.

Cet appareil numérique de la classe A respecte toutes les

exigences du Règlement sur le matériel brouilleur du Canada.

VCCI Statement

3Com offers product registration, case management, and repair

services through eSupport.3com.com. You must have a user

name and password to access these services, which are described

in this appendix.

To take advantage of warranty and other service benefits, you

must first register your product at: http://eSupport.3com.com/

3Com eSupport services are based on accounts that are created

or that you are authorized to access.

Solve Problems Online

3Com offers the following support tool:

 3Com Knowledgebase — Helps you to troubleshoot 3Com

products. This query-based interactive tool is located at:

http://knowledgebase.3com.com

It contains thousands of technical solutions written by 3Com

support engineers.

Purchase Extended Warranty and Professional

Services

To enhance response times or extend your warranty benefits, you

can purchase value-added services such as 24x7 telephone tech-

nical support, software upgrades, onsite assistance, or advanced

hardware replacement.

Experienced engineers are available to manage your installation

with minimal disruption to your network. Expert assessment and

implementation services are offered to fill resource gaps and

ensure the success of your networking projects. For more infor-

mation on 3Com Extended Warranty and Professional Services,

see: http://www.3com.com/

Contact your authorized 3Com reseller or 3Com for additional

product and support information. See the table of access num-

bers later in this appendix.

Access Software Downloads

You are entitled to bug fix / maintenance releases for the version

of software that you initially purchased with your 3Com product.

To obtain access to this software, you need to register your prod-

uct and then use the Serial Number as your login. Restricted

Software is available at: http://eSupport.3com.com/

To obtain software releases that follow the software version that

you originally purchased, 3Com recommends that you buy an

Express or Guardian contract, a Software Upgrades contract, or

an equivalent support contract from 3Com or your reseller. Sup-

port contracts that include software upgrades cover feature

enhancements, incremental functionality, and bug fixes, but they

do not include software that is released by 3Com as a sepa-

rately ordered product. Separately orderable software releases

and licenses are listed in the 3Com Price List and are available for

purchase from your 3Com reseller.

REGULATORY NOTICES

OBTAINING SUPPORT FOR YOUR PRODUCT

3Com offers telephone, internet, and e-mail access to technical

support and repair services. To access these services for your

region, use the appropriate telephone number, URL, or e-mail

address from the table in the next section.

Telephone Technical Support and Repair

To obtain telephone support as part of your warranty and other

service benefits, you must first register your product at:

http://eSupport.3com.com/

When you contact 3Com for assistance, please have the follow-

ing information ready:

 Product model name, part number, and serial number

 A list of system hardware and software, including revision

level

 Diagnostic error messages

 Details about recent configuration changes, if applicable

To send a product directly to 3Com for repair, you must first

obtain a return materials authorization number (RMA). Products

sent to 3Com without authorization numbers clearly marked on

the outside of the package will be returned to the sender

unopened, at the sender’s expense. If your product is registered

and under warranty, you can obtain an RMA number online at

http://eSupport.3com.com/. First-time users must apply for a user

name and password.

Telephone numbers are correct at the time of publication. Find a

current directory of 3Com resources by region at:

http://csoweb4.3com.com/contactus/

Country Telephone Number Country Telephone Number

Asia, Pacific Rim — Telephone Technical Support and Repair

Australia

Hong Kong

India

Indonesia

Japan

Malaysia

New Zealand

1800 075 316

2907 0456

000 800 440 1193

001 803 852 9825

03 3507 5984

1800 812 612

0800 450 454

Philippines

PR of China

Singapore

South. Korea

Tai wan

Thailand

1800 144 10220 or

029003078

800 810 0504

800 616 1463

080 698 0880

00801 444 318

001 800 441 2152

Pakistan Call the U.S. direct by dialing 00 800 01001, then dialing 800 763 6780

Sri Lanka Call the U.S. direct by dialing 02 430 430, then dialing 800 763 6780

Vietnam Call the U.S. direct by dialing 1 201 0288, then dialing 800 763 6780

You can also obtain non-urgent support in this region at this email address apr_technical_s[email protected]

Or request a return material authorization number (RMA) by FAX using this number: +61 2 9937 5048, or send an email at this email address:

ap_rma_requ[email protected]

Europe, Middle East, and Africa — Telephone Technical Support and Repair

From anywhere in these regions not listed below, call: +44 1442 435529

From the following countries, call the appropriate number:

Austria

Belgium

Denmark

Finland

France

Germany

Hungary

Ireland

Israel

Italy

0800 297 468

0800 71429

800 17309

0800 113153

0800 917959

0800 182 1502

06800 12813

1 800 553 117

180 945 3794

800 879489

Luxembourg

Netherlands

Norway

Poland

Portugal

South Africa

Spain

Sweden

Switzerland

U.K.

800 23625

0800 0227788

800 11376

00800 4411 357

800 831416

0800 995 014

900 938 919

020 795 482

0800 553 072

0800 096 3266

You can also obtain support in this region using this URL: http://emea.3com.com/support/email.html

You can also obtain non-urgent support in this region at these email addresses:

Technical support and general requests: [email protected]m

Return material authorization: warranty_repair@3com.com

Contract requests: emea_contract@3com.com

Latin America — Telephone Technical Support and Repair

Antigua

Argentina

Aruba

Bahamas

Barbados

Belize

Bermuda

Bonaire

Brazil

Cayman

Chile

Colombia

Costa Rica

Curacao

Ecuador

Dominican Republic

1 800 988 2112

0 810 444 3COM

1 800 998 2112

52 5 201 0010

1 800 998 2112

0800 13 3COM

1 800 998 2112

AT&T +800 998 2112

1 800 998 2112

AT&T +800 998 2112

Guatemala

Haiti

Honduras

Jamaica

Martinique

Mexico

Nicaragua

Panama

Paraguay

Peru

Puerto Rico

Salvador

Trinidad and Tobago

Uruguay

Venezuela

Virgin Islands

AT&T +800 998 2112

57 1 657 0888

AT&T +800 998 2112

1 800 998 2112

571 657 0888

01 800 849CARE

AT&T +800 998 2112

54 11 4894 1888

AT&T +800 998 2112

1 800 998 2112

AT&T +800 998 2112

1 800 998 2112

AT&T +800 998 2112

57 1 657 0888

You can also obtain support in this region in the following ways:

■ Spanish speakers, enter the URL: http://lat.3com.com/lat/support/form.html

■ Portuguese speakers, enter the URL: http://lat.3com.com/br/support/form.html

■ English speakers in Latin America, send e-mail to: lat_support_anc@3com.com

US and Canada — Telephone Technical Support and Repair

All locations: All 3Com products: 1 800 876 3266

documentation may be reproduced in any form or by any means or used to make

any derivative work (such as translation, transformation, or adaptation) without

permission from 3Com Corporation.

3Com Corporation reserves the right to revise this documentation and to make

changes in content from time to time without obligation on the part of 3Com

Corporation to provide notification of such revision or change.

3Com Corporation provides this documentation without warranty of any kind,

either implied or expressed, including, but not limited to, the implied warranties of

merchantability and fitness for a particular purpose. 3Com may make improvements

or changes in the product(s) and/or the program(s) described in this documentation

at any time.

UNITED STATES GOVERNMENT LEGENDS:

If you are a United States government agency, then this documentation and the

software described herein are provided to you subject to the following restricted

rights:

For units of the Department of Defense:

Restricted Rights Legend: Use, duplication or disclosure by the Government is

subject to restrictions as set forth in subparagraph (c) (1) (ii) for restricted Rights in

Technical Data and Computer Software clause at 48 C.F.R. 52.227-7013. 3Com

Centre, Boundary Way, Maylands Park South, Hemel Hempstead, Herts, HP2 7YU,

U.K.

For civilian agencies:

Restricted Rights Legend: Use, reproduction or disclosure is subject to restrictions set

forth in subparagraph (a) through (d) of the Commercial Computer Software -

Restricted Rights Clause at 48 C.F.R. 52.227-19 and the limitations set forth in

3Com Corporation’s standard commercial agreement for the software. Unpublished

rights reserved under the copyright laws of the United States.

If there is any software on removable media described in this documentation, it is

furnished under a license agreement included with the product as a separate

document, in the hard copy documentation, or on the removable media in a

directory file named LICENSE.TXT. If you are unable to locate a copy, please contact

3Com and a copy will be provided to you.

Unless otherwise indicated, 3Com registered trademarks are registered in the United

States and may or may not be registered in other countries.

3Com and the 3Com logo are registered trademarks of 3Com Corporation.

Other brand and product names may be registered trademarks or trademarks of their

respective holders.

General Environmental Statement

It is the policy of 3Com Corporation to be environmentally-friendly in all

operations. To uphold our policy, we are committed to:

 Establishing environmental performance standards that comply

with national legislation and regulations

 Conserving energy, materials and natural resources in all

operations

 Reducing the waste generated by all operations

 Ensuring that all waste conforms to recognized environmental

standards

 Maximizing the recyclable and reusable content of all products

 Ensuring that all products can be recycled, reused and disposed

of safely

 Ensuring that all products are labelled according to recognized

environmental standards

 Improving our environmental record on a continual basis

End Of Life Statement

3Com processes allow for the recovery, reclamation and safe disposal of

all end-of-life electronic components.

Regulated Materials Statement

3Com products do not contain any hazardous or ozone-depleting

material.

Enviromental Statement about the Documentation

The documentation for this product is printed on paper that comes from

sustainable, managed forests; it is fully biodegradeable and recyclable,

and is completely chlorine-free. The varnish is enviromentally-friendly, and

the inks are vegetable-based with a low heavy-metal content.

Product Registration

You can now register your 3Com Baseline Switch 2016/2024 on

the 3Com web site: http://eSupport.3com.com/

Documentation Feedback

Your suggestions are very important to us. They will help make

our documentation more useful to you. Please e-mail comments

about this document to 3Com at:

[email protected]

Please include the following information when commenting: the

document title, part number (shown at the bottom of this page),

and page number, if appropriate.

LEGAL NOTICES

ENVIROMENTAL STATEMENTS

PRODUCT REGISTRATION

Part Number: 10016425 Rev. AA

Published: September 2007

3com Baseline 2016 Manuel utilisateur

Marque: 3com

Modèle: Baseline 2016

Catégorie: Commutateurs réseau

Taper: Manuel utilisateur

Ce manuel convient également à

Baseline 2024

Télécharger le PDF

rapport

dans d''autres langues

English: 3com Baseline 2016 User manual

3com Baseline 2016 Manuel utilisateur

Ce manuel convient également à

3com Baseline 2016 Manuel utilisateur

dans d''autres langues

Documents connexes