GE IM5D Manuel utilisateur

Catégorie
Frigos
Taper
Manuel utilisateur
Icemaker Accessory Kit
IM-5D
239D4769P001 49-60740-1 01-16 GE
Safety Information ................ 2
Operating Instructions ............3
Automatic Icemaker ....................3
Preparing for Vacation .................3
When You Should Set the
Icemaker to OFF .......................3
Installation Instructions
Water Line Installation ...............4-7
Icemaker Installation ................8-12
Before You Call For Service .........13-15
Normal Sounds You May Hear ..........15
Consumer Support
Warranty ............................ 16
Consumer Support ................... 18
Owner’s Manual and
Installation Instructions
Machine à glaçons
Trousse
Manuel d’utilisation
et d’installation
Máquina de Hielos
Equipo de Accesorios
Manual del propietario
e instalación
READ AND FOLLOW THIS SAFETY INFORMATION CAREFULLY.
READ AND SAVE THESE INSTRUCTIONS
GE Appliances website
For more information on your refrigerator’s operation, visit www.GEAppliances.com or
call 800.GECARES (800.432.2737). In Canada visit GEAppliances.ca or call 800.561.3344.
This is the safety alert symbol. This symbol alerts you to potential hazards that can kill or hurt you and others. All safety
messages will follow the safety alert symbol and the word “DANGER”, “WARNING”, or “CAUTION”. These words are defined as:
Indicates a hazardous situation which, if not avoided, will result in death or serious injury.
Indicates a hazardous situation which, if not avoided, could result in death or serious injury.
Indicates a hazardous situation which, if not avoided, could result in minor or moderate injury.
REFRIGERATOR SAFETY INFORMATION
SAFETY
WARNING
WARNING
DANGER
CAUTION
n Unplug the refrigerator before installing ice
maker. Note: Power to the refrigerator cannot be
disconnected by any setting on the control panel.
n Replace all parts and panels before operating
refrigerator.
n Avoid contact with the moving parts of the ice maker
mechanism and with the heating element that
releases the cubes. Do not place fingers or hands on
the ice making mechanism while the refrigerator is
plugged in.
IMPORTANT SAFETY INSTRUCTIONS
To reduce the risk of injury when using your refrigerator, follow these basic
safety precautions.
2
About the automatic icemaker. GEAppliances.com
A newly-installed refrigerator may take 12 to 24 hours to begin making ice.
Feeler Arm
Automatic Icemaker
The icemaker will produce seven cubes
per cycle approximately 100–130 cubes
in a 24-hour period, depending on freezer
compartment temperature, room temperature,
number of door openings and other use
conditions.
The icemaker will fill with water when it cools to
15°F (–10°C). A newly installed refrigerator may
take 12 to 24 hours to begin making ice cubes.
If the refrigerator is operated before the water
line connection is made to the unit or if the
water supply to an operating refrigerator is
turned off, make sure that the icemaker is
turned off. Once the water has been connected
to the refrigerator, the icemaker may be turned
on. To turn the icemaker on or off, use the ICE
MAKER button on the control.
You may hear a buzzing sound each time the
icemaker fills with water.
Throw away the first few batches of ice to allow
the water line to clear.
Be sure nothing interferes with the sweep of the
feeler arm.
When the bin fills to the level of the feeler arm,
the icemaker will stop producing ice. It is normal
for several cubes to be joined together.
If ice is not used frequently, old ice cubes will
become cloudy, taste stale and shrink.
NOTE: In homes with lower-than-average water
pressure, you may hear the icemaker cycle
multiple times when making one batch of ice.
WARNING
To minimize the risk of personal injury, avoid contact with the moving parts of the ice
maker mechanism and with the heating element that releases the cubes. Do not place
fingers or hands on the ice making mechanism while the refrigerator is plugged in.
Refrigerator controls.
Icemaker setting
Press and hold to turn your icemaker on/off.
When you should turn the icemaker OFF
When the ice storage bin is removed for more than a minute
or two.
When the water supply will be shut off for several hours.
When the refrigerator will not be used for several days.
For long vacations or absences, remove food and unplug the
refrigerator. Clean the interior with a baking soda solution of
one tablespoon (15 ml) of baking soda to one quart (1 liter) of
water. Leave the doors open.
Turn refrigerator off at control (see Quick Install Guide).
If the temperature can drop below freezing, have a qualified
service technician drain the water supply system to prevent
serious property damage due to flooding.
Before going on vacation
1) Turn the cooling system off (see Quick Install Guide) or unplug
the refrigerator.
2) Empty ice bucket
3) Turn water supply off
If you cut the water supply off, turn off the icemaker (see
above).
Upon returning from vacation:
1) Replace the water filter (see Owner’s Manual).
2) Run 2 gallons of water through the cold water dispenser
(about 5 minutes) to flush the system.
3) Turn cooling system on (see Quick Install Guide).
4) Reset Filter Status message (see Quick Use & Care Guide). If
you cut the water supply, turned on icemaker (see above).
3
Icemaker
Recommended copper water supply kits are WX8X2,
WX8X3 or WX8X4, depending on the amount of
tubing you need. Approved plastic water supply
lines are GE SmartConnect
Refrigerator Tubing
(WX08X10006, WX08X10015 and WX08X10025).
When connecting your refrigerator to a GE Reverse
Osmosis Water System, the only approved installation
is with a GE RVKit. For other reverse osmosis water
systems, follow the manufacturer’s recommendations.
If the water supply to the refrigerator is from
a Reverse Osmosis (RO) Water Filtration System
AND the refrigerator also has a water filter,
use the refrigerator’s filter bypass plug. Using
the refrigerator’s water filtration cartridge in
conjunction with the RO water filter can result in
hollow ice cubes.
This water line installation is not warranted
by the refrigerator or icemaker manufacturer.
Follow these instructions carefully to minimize
the risk of expensive water damage.
Water hammer (water banging in the pipes)
in house plumbing can cause damage to
refrigerator parts and lead to water leakage
or flooding. Call a qualified plumber to correct
water hammer before installing the water supply
line to the refrigerator.
To prevent burns and product damage, do not
hook up the water line to the hot water line.
If the refrigerator is operated before the water
connection is made to the icemaker, press and
release the ICE MAKER button on the control panel
to disengage the icemaker. When the refrigerator
has been connected to the water supply, press and
release the ICE MAKER button on the control panel
to re-engage the icemaker.
Do not install the icemaker tubing in areas where
temperatures fall below freezing.
When using any electrical device (such as a
power drill) during installation, be sure the device
is double insulated or grounded in a manner to
prevent
the hazard of electric shock, or is battery powered.
All installations must be in accordance with local
plumbing code requirements.
BEFORE YOU BEGIN
WHAT YOU WILL NEED
Copper or GE SmartConnect
Refrigerator Tubing
kit, 1/4 outer diameter to connect
the refrigerator to the water supply. If using
copper, be sure both ends of the tubing are
cut square.
To determine how much tubing you need:
measure the distance from the water valve
on the back of the refrigerator to the water supply
pipe. Be sure there is sufficient extra tubing to allow
the refrigerator to move out from the wall after
installation.
GE SmartConnect
Refrigerator Tubing Kits are
available in the following lengths:
8 (2.4 m) – WX08X10006
15 (4.6 m) – WX08X10015
25 (7.6 m) – WX08X10025
NOTE: The only GE approved plastic tubing
is that supplied in GE SmartConnect
Refrigerator
Tubing kits. Do not use any other plastic water
supply line because the line is under pressure at all
times. Certain types of plastic will crack or rupture
with age and cause water damage to your home.
A GE water supply kit (containing tubing,
shutoff valve and fittings listed below) is available
at extra cost from your dealer or from Parts
and Accessories, 800.626.2002 (in Canada
1.800.661.1616).
A cold water supply. The water pressure must be
between 20 and 120 p.s.i. (1.4–8.1 bar).
Power drill.
1/2 or adjustable wrench.
Straight and Phillips blade screwdriver.
Two 1/4 outer diameter compression nuts
and 2 ferrules (sleeves)—to connect the copper
tubing to the shutoff valve and the refrigerator
water valve.
OR
If you are using a GE SmartConnect
Refrigerator Tubing kit, the necessary fittings
are pre-assembled to the tubing.
4
Installing the water line.
If your existing copper water line has a flared
fitting at the end, you will need an adapter
(available at plumbing supply stores) to connect
the water line to the refrigerator OR you can cut
off the flared fitting with a tube cutter and then
use a compression fitting. Do not cut formed end
from GE SmartConnect
Refrigerator tubing.
Shutoff valve to connect to the cold water line.
The shutoff valve should have a water inlet with
a minimum inside diameter of 5/32 at the point of
connection to the COLD WATER LINE. Saddle-type
shutoff valves are included in many water supply
kits. Before purchasing, make sure a saddle-type
valve complies with your local plumbing codes.
WHAT YOU WILL NEED (CONT.)
SHUT OFF THE MAIN WATER SUPPLY
Turn on the nearest faucet long enough to clear
the line of water.
Install the shutoff valve on the nearest frequently used
drinking water line.
1
Choose a location for the valve that is easily
accessible. It is best to connect into the side
of a vertical water pipe. When it is necessary
to connect into a horizontal water pipe, make
the connection to the top or side, rather than at
the bottom, to avoid drawing off any sediment
from the water pipe.
CHOOSE THE VALVE LOCATION
2
DRILL THE HOLE FOR THE VALVE
3
Drill a 1/4 hole in the water pipe (even if using
a self-piercing valve), using a sharp bit. Remove
any burrs resulting from drilling the hole in
the pipe.
Take care not to allow water to drain into
the drill.
Failure to drill a 1/4 hole may result in reduced
ice production or smaller cubes.
5
GEAppliances.com
Fasten the shutoff valve to the cold water pipe
with the pipe clamp.
NOTE: Commonwealth of Massachusetts
Plumbing Codes 248CMR shall be adhered
to. Saddle valves are illegal and use is not
permitted in Massachusetts. Consult with your
licensed plumber.
FASTEN THE SHUTOFF VALVE
4
Pipe Clamp
Vertical Cold Water
Pipe
Saddle-Type
Shutoff Valve
Place the compression nut and ferrule (sleeve)
for copper tubing onto the end of the tubing
and connect it to the shutoff valve.
Make sure the tubing is fully inserted into
the valve. Tighten the compression nut securely.
For plastic tubing from a GE SmartConnect
Refrigerator Tubing kit, insert the molded end
of the tubing into the shutoff valve and tighten
compression nut until it is hand tight, then
tighten one additional turn with a wrench. Over
tightening may cause leaks.
NOTE: Commonwealth of Massachusetts
Plumbing Codes 248CMR shall be adhered
to. Saddle valves are illegal and use is not
permitted in Massachusetts. Consult with your
licensed plumber.
CONNECT THE TUBING TO THE VALVE
7
Saddle-Type
Shutoff Valve
Compression Nut
Packing Nut
Outlet Valve
Ferrule (sleeve)
Turn the main water supply on and flush out
the tubing until the water is clear.
Shut the water off at the water valve after
about one quart (1 liter or 2 minutes) of water
has been flushed through the tubing.
FLUSH OUT THE TUBING
8
SmartConnect
Tubing
Tighten the clamp screws until the sealing
washer begins to swell.
NOTE: Do not over tighten or you may crush
the tubing.
TIGHTEN THE PIPE CLAMP
5
Washer
Inlet End
Pipe Clamp
Clamp
Screw
Route the tubing between the cold water line
and the refrigerator.
Route the tubing through a hole drilled in the
wall or floor (behind the refrigerator or adjacent
base cabinet) as close to the wall as possible.
ROUTE THE TUBING
6
6
Installing the water line. (cont.)
CONNECTING THE REFRIGERATOR
TO THE HOUSE WATER LINE
A cold water supply is required for automatic icemaker
operation. If there is not a cold water supply, you will
need to provide one. See Installing the Water Line
section.
NOTES:
Before making the connection to the refrigerator, be
sure the refrigerator power cord is not plugged into
the wall outlet.
If you are not using your refrigerator water filter, we
recommend installing one if your water supply has
sand or particles that could clog the screen of the
refrigerator’s water valve. Install it in the water line
near the refrigerator. If using GE SmartConnect
Refrigerator Tubing Kit, you will need an additional
tube (WX08X10002) to connect the filter. Do not cut
plastic tube to install filter.
Before connecting the water line to the house, purge
the house line for at least 2 minutes.
If you are using copper tubing, place a compression
nut and ferrule (sleeve) onto the end of the tubing
coming from the house cold water supply.
If you are using the GE SmartConnect
tubing, the
nuts are already assembled to the tubing.
If you are using copper tubing, insert the end of the
tubing into the refrigerator connection, at the back of
the refrigerator, as far as possible. While holding the
tubing, tighten the fitting.
If you are using GE SmartConnect
tubing, insert
the molded end of the tubing into the refrigerator
connection, at the back of the refrigerator, and tighten
the compression nut until it is hand tight. Then tighten
one additional turn with a wrench. Over tightening
may cause leaks.
Fasten the tubing into the clamp provided to hold it in
position. You may need to pry open the clamp.
9
1/4
Compression
Nut
Ferrule
(sleeve)
SmartConnect
Tubing
Refrigerator
Connection
7
GEAppliances.com
BEFORE YOU BEGIN
Installation IM-5D
Instructions Icemaker Kit
Read these instructions completely and carefully.
IMPORTANT – Save these instructions
for local inspector’s use.
IMPORTANT – Observe all governing
codes and ordinances.
Note to Installer – Be sure to leave these
instructions with the Consumer.
Note to Consumer – Keep these instructions
for future reference.
• Skill level – Installation of this appliance requires
basic mechanical and electrical skills.
• Completion time – 20–60 minutes
Proper installation is the responsibility of the
installer.
Product failure due to improper installation is not
covered under the Warranty.
Questions? Call 800.GE.CARES (800.432.2737) or Visit our Website at: GEAppliances.com
In Canada, call 1.800.561.3344 or Visit our Website at: geappliances.ca
If the unit is damaged in shipment, return the unit to the
store in which it was bought for repair or replacement.
If the unit is damaged by the customer, repair or
replacement is the responsibility of the customer.
If the unit is damaged by the installer (if other than
the customer), repair or replacement must be made by
arrangement between customer and installer.
DAMAGE – SHIPMENT/INSTALLATION
CONTENTS OF KIT IM-5D
Icemaker
Large Ice Bucket*
Small Ice Bucket*
(for counter depth models)
Icemaker Fill Cup
Hex Head Screw
(3/4”)
Installation
Instructions
*Kit comes with 2 ice buckets.
The smaller is for counter
depth models. Use extra
bucket for additional ice
storage or recycle.
Warranty Label
Ice Bucket Cover
(for large ice bucket)
WARNING
To eliminate the risk of
electric shock or injury during installation,
you must first unplug the refrigerator
before proceeding. Failure to follow these
instructions can result in electrical shock.
Small Flat-head
Screwdriver
TOOLS YOU WILL NEED
1/4” Nut Driver
8
Installation
Instructions
ICEMAKER
WARRANTY VERIFICATION
Shut the water off at the water vlave.
SHUT OFF THE WATER SUPPLY
Saddle-Type
Shutoff Valve
3/8” Socket
Ratchet/Driver
REMOVE THE OUTLET COVERS
Inside the freezer,
remove the 2
outlet covers from
the side wall.
Remove the outlet
covers with a
small flat-blade
screwdriver.
For round
cover: Insert the
screwdriver into
one of the smaller
outermost slots
and push in firmly
to release the
round cover.
For rectangular
cover: insert the screwdriver into the slot at
the top of the cover. Lift the screwdriver up
to release the snap and pull the cover out
away from liner. (This part is disposable and
may break when removed.)
Remove the icemaker power cord plug from
the pocket in the side wall.
Installation Instructions
INSTALLING ICEMAKER
9
PREPARE FOR INSTALLATION
Pull the freezer door open to full extension.
Remove 3 attachment screws, located at
the bottom on each side of the freezer door
using 3/8” hex socket driver.
CAUTION
Lifting Hazard
Freezer door is heavy Use both hands to
secure the door before lifting.
Lift the freezer
door to
disengage it
from the slide
mechanism
The door can
safely rest on
the bottom. Do
not rest the door
on any other
surfaces to avoid
scratches.
REMOVE FREEZER DRAWER
Remove the top freezer drawer by fully
extending the drawer then lifting up and out.
Push the bottom
basket back
until the slide
mechanism self
retracts.
INSTALL THE ICEMAKER FILL CUP
Remove the ice maker
from the kit, install the
icemaker fill cup that
came with your kit
into the icemaker as
shown.
For New Install
Choose the
appropriate size
ice bucket from
the kit. Place the
ice bucket in the
left side of the
freezer basket,
upside down,
with taller end
toward the rear
of the basket.
1
2
3
4
Outlet covers
Icemaker power cord
3 Screws
INSTALLING ICEMAKER (cont.)
10
Installation Instructions
PLUG IN THE ICEMAKER
Place icemaker and fill cup on top of lower
basket contents, or ice bucket (for support),
with the wire and connectors facing up.
Install the six pin connector first and then
the four pin connector.
CHECK INSTALLATION
Push the icemaker back toward the rear
of the cabinet so the mounting screw
hole in the icemaker flange aligns with
the mounting hole in the freezer side wall,
making sure wires are not hanging outside
of wire housing.
Install self-tapping
hex head screw
from the kit into
the hole in the
flange of the
icemaker.
REMOVE THE ICE BUCKET
Remove the ice bucket from the basket.
For non-counter depth modles: Install the ice
bucket cover onto the ice bucket by snapping
pins into holes at the back of the ice bucket.
NOTE: Kit comes with two ice buckets. Counter
depth models will use smaller bucket. Use extra
bucket (in models with “Y” in model number
such as GYE) for additional ice storage or it can
be recycled.
MOUNT THE ICEMAKER
Lift the icemaker up and rotate to align the
slots on the side of the icemaker with the
mounting pins
in the freezer
wall. Slide the
icemaker back
so the fill tube
on the top
wall fits inside
the fill cup
opening.
Make sure:
- The connector plugs are still firmly in the
sockets.
- The fill tube extends into the fill cup
opening at the back of the icemaker.
- The icemaker is level.
Check the wiring to make sure the ice maker
is plugged in correctly.
5
7
8
6
6-Pin Connector
6-Pin Connector
4-Pin Connector
4-Pin Connector
Ice Bucket
Cover
Ice Bucket
(Front)
Fill Tube
Mounting Pins
Mounting Screw
Screw
Hole
Fill Cup
Hex Head
Mounting Screw
11
Installation Instructions
REMOVE FREEZER DRAWER CORNER
Remove the drawer corner piece by pulling
out and up on three tabs while pushing
down on the back of the drawer. Then pull
out the side flange while pulling up on the
corner piece to complete the removal.
REPLACE FREEZER DOOR (Cont.)
For adjusting freezer door gaps, follow the
instructions in the Owner’s Manual.
Replace freezer basket onto the slide
brackets and make sure the freezer door
operates and closes freely.
REPLACE FREEZER DOOR
Pull the lower basket and slide mechanism
to full extension using both hands.
Remove the basket resting on the slides.
If the basket is full of frozen goods, lift the
basket and set to the rear of the freezer
compartment until after the freezer door is
located on slides.
CAUTION
Lifting Hazard
Freezer door is heavy Use both hands to
secure the door before lifting.
Lift the freezer door and align the tabs on
the door bracket sides with the square holes
in slide mechanisms.
Replace the attachment screws and torque
the screws to 65 in-lb.
RE-INSTALL FREEZER DRAWER
Re-install freezer drawer by placing the rear
drawer wheels onto the top of the track
mounted to the side of the freezer walls. The
front wheels on the freezer drawer should
be on top of the bottom basket sides. Place
the ice bucket in the drawer and push the
drawer into the freezer with the front of
the bucket (see page 10) to the front of the
basket,.
Make sure:
- The ice bucket does not hit the icemaker
arm and the freezer drawer retracts
completely into the freezer compartment.
- The fill tube extends into the fill cup
opening at the back of the icemaker.
9
10
10
11
Align and insert tab
on Freezer Door
Bracket with slot
on Freezer Slide
Bracket.
NOTE: Place one
side in first and
then align the other
side.
PLUG IN THE REFRIGERATOR
Plug in the refrigerator.
Arrange the coil of tubing
so that it does not vibrate
against the back of the
refrigerator or against the
wall. Push the refrigerator
back to the wall.
INSTALLING ICEMAKER (cont.)
12
Installation Instructions
START THE ICEMAKER
Set the icemaker to ON. See page 3.
16
15
ATTACH WARRANTY LABEL
A label is provided with this kit to record the
date of installation for warranty purposes.
Apply it to the inside of the refrigerator
under existing model/serial number label on
the side wall of the fresh food compartment.
KEEP THIS MANUAL
The warranty for the icemaker is printed in
this manual. Keep this manual with your
Refrigerator Owner’s Manual.
The icemaker installation inside the freezer is
now complete.
TURN THE WATER ON AT THE
SHUTOFF VALVE
Tighten any connections that leak.
12
13
14
Problem Possible Causes What To Do
Automatic icemaker does not
work
Freezer compartment too
warm.
After installing the kit, allow the refrigerator to
completely cool down for 24 hours. Once the
compartment is cool, the icemaker will begin ice
production.
Icemaker is not turned on Use the ICE MAKER button on the control.
Icemaker is not plugged in
correctly
Check that the icemaker cord pug is fully inserted into
the socket. See Plug in the Icemaker, page 10.
Water line is kinked Check that the plastic water line running from the valve
to the water tube inlet is not kinked. See Connect the
Water Line. A kink in the water line will restrict flow of
water.
Water supply tuned off or not
connected
After installing the kit, make sure the house water
supply to the refrigerator has been turned on.
Piled up cubes in the storage
bin cause the icemaker to shut
off
Level cubes by hand.
Before you call for service…
GEAppliances.com
Troubleshooting Tips
Save time and money! Review the following chart first
and you may not need to call for service.
13
Adhesive-backed
Fasteners
Water Line
Tubing
Before you call for service…
Troubleshooting Tips
Save time and money! Review the following chart first
and you may not need to call for service.
14
Problem Possible Causes What To Do
Leaking water around the fill cup Fill tube not correctly seated
in the fill cup
Check that the fill tube is correctly inserted in the fill cup
opening. See Mount the Icemaker.
Leaking water behind the
refrigerator
House supply not properly
connected to the water valve
Check that the house supply is firmly attached to the
water valve. See Water Line Installation Instructions.
Water line not
connected to
the water tube
inlet
Slow ice/freezer not cold enough Door left open Check to see if package is holding door open.
Temperature control not set
cold enough
See Controls-Temperature Settings in the Owner’s Manual
(Web only) or the Quick Installation Guide - Controls of the
refrigerator.
Ice cubes too small/slow ice Water shutoff valve
connecting refrigerator to
house water line may be
clogged
We recommend drilling a 1/4” hole in the water pipe to
connect the water shut-off valve. Failure to drill a 1/4”
hole may result in reduced ice
production or smaller cubes.
See Installing the Water Line.
Water line is kinked Check that the plastic water line running from the valve to
the water tube inlet is not kinked. See Connect the Water
Line. A kink in the water line will restrict flow of water.
Check water filter See Owner’s Manual (Web Only), and the Quick Use and
Care.
1/4
Compression
Nut
Ferrule
(sleeve)
SmartConnect
Tubing
Refrigerator
Connection
Drill 1/4" hole
in water pipe
Fill Tube
Fill Cup
Adhesive-backed
Fasteners
Water Line
Tubing
15
Problem Possible Causes What To Do
Ice cubes not landing in bucket Icemaker cord causing
icemaker bucket misalignment
Be sure ice maker wires are not hanging outside of the
wiring enclosure on back of ice maker. (See step 7 page 10)
Ice cubes have odor/taste Ice storage bin needs cleaning Empty the wash bin. Discard old cubes
Food transmitting odor/taste
to ice cubes
Wrap foods well. Move strong tasting foods away from ice
bucket, meat, etc.
Interior of refrigerator needs
cleaning
See Care and Cleaning in the Owner’s Manual (Web Only,)
and the Quick Installation guide of the refrigerator.
Ice cubes hollow Water supply in RO Water
Filtration System.
See Installing Water Line, use Filter bypass plug.
Interior of refrigerator needs
cleaning
See Care and Cleaning in the Owner’s Manual (Web Only,)
and the Quick Installation guide of the refrigerator.
Frequent “buzzing” sound Normal operation During normal operation, the water valve will “buzz” when
the icemaker fills with water.
GEAppliances.com
The icemaker water valve will buzz when the icemaker fills
with water. If the icemaker is on it will buzz even if it has
not yet been hooked up to water. Keeping the icemaker on
before it is hooked up to water can damage the icemaker. To
prevent this, turn the icemaker off. This will stop the buzzing.
The sound of cubes dropping into the bin and water running
in the pipes as the icemaker refills.
Normal sounds you may hear
16
Icemaker Warranty.
All warranty service provided by our Factory Service Centers, or an
authorized Customer Care
®
technician. To schedule service, on-line,
visit us at GEAppliances.com, or call 800.GE.CARES (800.432.2737). In
Canada, call 1.800.561.3344. Please have serial number and model
number available when calling for service.
For The Period Of: We Will Replace:
One Year Any part of the icemaker which fails due to a defect in materials or workmanship.
From the date of the During this limited one-year warranty, GE will provide, free of charge, replacement parts
original purchase for any defective part in your icemaker kit.
Service trips to your home to teach you how to use
the product.
Improper installation.
You are responsible for providing adequate electrical,
plumbing, and other connecting facilities, including the
water line to the icemaker and the water line installation.
Failure of the product if it is abused, misused, or used for
other than the intended purpose or used commercially.
Replacement of house fuses or resetting of circuit
breakers.
Damage to the product caused by accident, fire, floods
or acts of God.
Incidental or consequential damage caused by possible
defects with this appliance.
Product not accessible to provide required service.
What Is Not Covered (for customers in the United States):
This warranty is extended to the original purchaser and any succeeding owner for products purchased for home
use within the USA. If the product is located in an area where service by a GE Authorized Servicer is not available,
you may be responsible for a trip charge or you may be required to bring the product to an Authorized GE Service
location for service. In Alaska, the warranty excludes the cost of shipping or service calls to your home.
Some states do not allow the exclusion or limitation of incidental or consequential damages. This warranty gives
you specific legal rights, and you may also have other rights which vary from state to state. To know what your
legal rights are, consult your local or state consumer affairs office or your state’s Attorney General.
Warrantor: General Electric Company. Louisville, KY 40225
Staple your receipt here.
Proof of the original purchase
date is needed to obtain service
under the warranty.
What Is Not Covered (for customers in Canada):
Service trips to your home to teach you how to use
the product.
Read your Owner’s Manual. If you then have any questions
about
operating the product, please contact
your dealer or
our Consumer Relations office at:
General Manager, Customer Relations
GE Appliances, Appliance Park
Louisville, KY 40225
Improper installation.
If you have an installation problem, contact your dealer
or installer. You
are responsible for providing adequate
electrical, exhausting and other connecting facilities.
Replacement of house fuses or resetting
of circuit
breakers.
Failure of the product if it is misused, or used for other
than the intended purpose or used commercially.
Damage to product caused by accident,
fire, floods or
acts of God.
WARRANTOR IS NOT RESPONSIBLE FOR CONSE QUEN TIAL DAMAGES.
EXCLUSION OF IMPLIED WARRANTIES—Your sole and exclusive remedy is product repair as provided in
this Limited Warranty. Any implied warranties, including the implied warranties of merchantability or
fitness for a particular purpose, are limited to one year or the shortest period allowed by law.
17
Notes.
GEAppliances.com
Printed in the United States
Consumer Support.
GE Appliances Website In the U.S.: GEAppliances.com
Have a question or need assistance with your appliance? Try the GE Appliances Website 24 hours a day,
any day of the year! For greater convenience and faster service, you can now download Owner’s Manuals,
order parts or even schedule service on-line. In Canada: www.geappliances.ca
Schedule Service In the U.S.: GEAppliances.com
Expert GE repair service is only one step away from your door. Get on-line and schedule your service at your
convenience any day of the year! Or call 800.GE.CARES (800.432.2737) during normal business hours.
In Canada, visit www.geppliances.ca
Real Life Design Studio In the U.S.: GEAppliances.com
GE supports the Universal Design concept—products, services and environments that can be used by people of
all ages, sizes and capabilities. We recognize the need to design for a wide range of physical and mental abilities
and impairments. For details of GE’s Universal Design applications, including kitchen design ideas for people with
disabilities, check out our Website today. For the hearing impaired, please call 800.TDD.GEAC (800.833.4322).
In Canada, visit www.geppliances.ca.
Extended Warranties In the U.S.: GEAppliances.com
Purchase a GE extended warranty and learn about special discounts that are available while your warranty is still
in effect. You can purchase it on-line anytime, or call 800.626.2224 during normal business hours. GE Consumer Home
Services will still be there after your warranty expires. In Canada, call 1.800.290.9029
Parts and Accessories In the U.S.: GEApplianceParts.com
Individuals qualified to service their own appliances can have parts or accessories sent directly to their homes
(VISA, MasterCard and Discover cards are accepted). Order on-line today, 24 hours every day or by phone at
800.626.2002 during normal business hours.
Instructions contained in this manual cover procedures to be performed by any user. Other servicing generally
should be referred to qualified service personnel. Caution must be exercised, since improper servicing may cause
unsafe operation.
Customers in Canada should consult the yellow pages for the nearest GE Appliances Service Center or
www.geappliacnes.ca.
Contact Us In the U.S.: GEAppliances.com
If you are not satisfied with the service you receive from GE, contact us on our Website with all the details including
your phone number, or write to: General Manager, Customer Relations
GE Appliances, Appliance Park
Louisville, KY 40225
In Canada, visit www.geppliances.ca.
Register Your Appliance In the U.S.: GEAppliances.com
Register your new appliance on-line—at your convenience! Timely product registration will allow for enhanced
communication and prompt service under the terms of your warranty, should the need arise. You may also
mail in the pre-printed registration card included in the packing material, or detach and use the form in this
Owner’s Manual. In Canada: www.geappliances.ca
Trousse Machine à glaçons
IM-5D
Mesures de sécurité ............................ 2
Instructions de fonctionnement ...............3
La machine à glaçons automatique ..................3
Préparation à un départ de longue durée ............3
Quand devez-vous éteindre la machine à glaçons? ...3
Instructions d’installation
Installation de la conduite d’eau .................. 4-7
Installation de la machine à glaçons pour ........8-12
Avant d’appeler un réparateur ..................13-15
Bruits normaux que vous pouvez entendre ......... 15
Services aux consommateurs
Garantie ..........................................16
Soutien au consommateur ........................18
Manuel d’utilisation
et d’installation
LISEZ ET SUIVEZ SOIGNEUSEMENT CES MESURES DE SÉCURITÉ.
LISEZ ET CONSERVEZ CES INSTRUCTIONS.
2
Site Internet d’Électroménagers GE
Pour de plus amples informations sur le fonctionnement de votre réfrigérateur, consultez le
site www.electromenagersge.ca ou composez le 800.561.3344.
CONSIGNES DE SÉCURITÉ POUR LE RÉFRIGÉRATEUR
SÉCURITÉ
Ce symbole représente une alerte de sécurité. Ce symbole vous avise de dangers possibles pouvant causer
la mort, des blessures ou autres. Tous les messages de sécurité seront précédés du symbole d’alerte de sécurité
ainsi que des mots « DANGER », « AVERTISSEMENT » ou « MISE EN GARDE ». Ces messages sont les suivants :
Signale une situation qui présente un danger imminent et qui, si elle n’est pas évitée, entraînera des blessures
graves, voire la mort.
Signale une situation qui présente un danger imminent et qui, si elle n’est pas évitée, peut entraîner des
blessures graves, voire la mort.
.
Signale une situation qui présente un danger imminent et qui, si elle n’est pas évitée, peut entraîner des
blessures mineures ou graves.
AVERTISSEMENT
DANGER
IMPORTANTES CONSIGNES DE SÉCURITÉ
Pour réduire le risque d’incendie, d’explosion, de choc électrique ou de blessures
lorsque vous utilisez votre réfrigérateurde , veuillez suivre ces consignes de sécurité :
AVERTISSEMENT
n Débranchez le réfrigérateur avant d’installer la
machine à glaçons. Remarque : L’alimentation
électrique à l’appareil ne peut pas être débranchée à
partir du panneau de commande.
n Replacez toutes les pièces et les panneaux avant de
faire fonctionner le réfrigérateur.
n Évitez de toucher les pièces mobiles du mécanisme
de la machine à glaçons ainsi que l’élément chauffant
qui libère les cubes. Ne placez ni les doigts ni les mains
sur le mécanisme de la machine à glaçons lorsque le
réfrigérateur est branché.
ATTENTION
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16
  • Page 17 17
  • Page 18 18
  • Page 19 19
  • Page 20 20
  • Page 21 21
  • Page 22 22
  • Page 23 23
  • Page 24 24
  • Page 25 25
  • Page 26 26
  • Page 27 27
  • Page 28 28
  • Page 29 29
  • Page 30 30
  • Page 31 31
  • Page 32 32
  • Page 33 33
  • Page 34 34
  • Page 35 35
  • Page 36 36
  • Page 37 37
  • Page 38 38
  • Page 39 39
  • Page 40 40
  • Page 41 41
  • Page 42 42
  • Page 43 43
  • Page 44 44
  • Page 45 45
  • Page 46 46
  • Page 47 47
  • Page 48 48
  • Page 49 49
  • Page 50 50
  • Page 51 51
  • Page 52 52
  • Page 53 53
  • Page 54 54
  • Page 55 55
  • Page 56 56

GE IM5D Manuel utilisateur

Catégorie
Frigos
Taper
Manuel utilisateur

dans d''autres langues