Sony AK8MV65STF Manuel utilisateur

Catégorie
Lecteur CD
Taper
Manuel utilisateur

Ce manuel convient également à

© 2004 Sony Corporation
US
MV-65ST
For installation and connections, refer to “Connection” on page 8.
En ce qui concerne l’installation et les raccordements, reportez-vous à la section
« Raccordements », page 8.
Si desea obtener información sobre la instalación y las conexiones, consulte el
apartado “Conexiones” de la página 8.
Owner’s Record
The model and serial numbers are located on the bottom of the unit.
Record these numbers in the space provided below.
Refer to these numbers whenever you call upon your Sony dealer regarding this
product.
Model No. MV-65ST Serial No.
2-021-315-14 (1)
Operating Instructions
Mode d’emploi
Manual de instrucciones
Portable DVD
Player
FR
ES
2
DANGER INVISIBLE
AVOID DIRECT EXPOSURE TO BEAM.
LASER RADIATION WHEN OPEN.
CAUTION
The use of optical instruments with this
product will increase eye hazard.
CAUTION
Use of controls or adjustments or
performance of procedures other than
those specified herein may result in
hazardous radiation exposure.
This is located on the drive unit's internal
chassis.
To prevent fire or shock hazard, do not
expose the unit to rain or moisture.
This symbol is intended to
alert the user to the presence of
uninsulated “dangerous
voltage” within the product’s
enclosure that may be of
sufficient magnitude to
constitute a risk of electric
shock to persons.
This symbol is intended to
alert the user to the presence of
important operating and
maintenance (servicing)
instructions in the literature
accompanying the appliance.
Warning
Warning
This equipment has been tested and found to
comply with the limits for a Class B digital
device, pursuant to Part 15 of the FCC Rules.
These limits are designed to provide
reasonable protection against harmful
interference in a residential installation. This
equipment generates, uses, and can radiate
radio frequency energy and, if not installed
and used in accordance with the instructions,
may cause harmful interference to radio
communications. However, there is no
guarantee that interference will not occur in a
particular installation. If this equipment does
cause harmful interference to radio or
television reception, which can be determined
by turning the equipment off and on, the user
is encouraged to try to correct the interference
by one or more of the following measures:
— Reorient or relocate the receiving
antenna.
— Increase the separation between the
equipment and receiver.
— Connect the equipment into an outlet on
a circuit different from that to which the
receiver is connected.
— Consult the dealer or an experienced
radio/TV technician for help.
You are cautioned that any changes or
modifications not expressly approved in this
manual could void your authority to operate
this equipment.
CAUTION
The use of optical instruments with this
product will increase eye hazard.
Operation is subject to the following two
conditions: (1) this device may not cause
interference, and (2) this device must accept
any interference, including interference that
may cause undesired operation of the device.
For the customers in the United
States
This product contains mercury. Disposal of
this product may be regulated if sold in the
United States. For disposal or recycling
information, please contact your local
authorities or the Electronics Industries
Alliance (http://www.eiae.org).
3
Table of Contents
Welcome ! .............................................................. 4
Precautions............................................................ 4
About this manual ............................................... 5
About discs this player can play ........................ 6
Connection ............................................................ 8
Resetting the player ........................................... 10
Location of controls ........................................... 11
Various Playback
Playing a disc ...................................................... 13
Searching a chapter/title/track directly ..........14
Resume playback .................................................15
Using MP3/JPG menu ........................................15
Displaying elapsed time ................................... 16
Changing the subtitle language ....................... 17
Using a DVD menu............................................ 18
Using the TOP MENU button ............................18
Using the MENU button .....................................18
Changing the audio language .......................... 19
Changing angles................................................. 19
Changing the audio output .............................. 20
Using the PBC (playback control) function.... 20
Changing Setup
System settings — SYSTEM menu .................. 21
Selecting the language on the menus
— OSD LANGUAGE.....................................21
Setting the screen saver
— SCREEN SAVER ........................................22
Returning this player to the factory setting
— LOAD SETUP DEF....................................22
Settings for DVD playback
— DVD SETUP menu .................................. 22
Selecting the audio language for DVD
AUDIO .......................................................22
Displaying the subtitles for DVD
— SUBTITLE ...................................................23
Setting the aspect ratio for the TV screen
— TV SCREEN ...............................................23
Displaying the multi-angle notice
— ANGLE MARK ..........................................23
Preparing for the initial parental setting
— PARENTAL CONTROL ..........................23
Setting the password — PASS WORD ..............24
Selecting the speaker mode
— SPEAKER menu ....................................... 25
Selecting the downmix mode
— DOWNMIX ................................................25
Selecting the digital audio output mode
— AUDIO menu ........................................... 25
Selecting the color system for the output
video signal — VIDEO menu ..................... 26
Monitoring video signals input from the
connected device ........................................... 26
Selecting the color system for the input
video signal.................................................... 27
Settings by using the MENU button on the
monitor ........................................................... 27
Adjusting the contrast .........................................27
Adjusting the brightness.....................................28
Adjusting the color ..............................................28
Adjusting the hue (NTSC only) .........................28
Adjusting the dimmer .........................................28
Resetting the adjustments...................................28
Setting the screen mode ......................................28
Setting the FM transmitter..................................29
Setting the blue background screen ..................29
Exiting the menu operation ................................29
Turning the image upside down...................... 30
Setting the reference volume ............................ 30
Additional information
Maintenance........................................................ 31
Notes on discs..................................................... 32
About MP3 files .................................................. 33
Specifications ...................................................... 34
Troubleshooting.................................................. 35
Error display ....................................................... 36
Language Code List ........................................... 37
4
Precautions
To avoid the risk of serious injury or accident,
read the following precautions before
installing and operating the player.
On safety
Do not put any foreign objects in the DC IN
12V jack.
On power sources
Use house current or car battery (12 V DC).
For use in your house, use the AC power
adaptor supplied with the player. Do not use
any other AC power adaptor since it may
cause the player to malfunction.
Connect the AC power adaptor to an easily
accessible AC outlet. Should you notice an
abnormality in the AC power adaptor,
disconnect it from the AC outlet
immediately.
The player is not disconnected from the AC
power source (mains) as long as it is
connected to the wall outlet, even if the
player itself has been turned off.
If you are not going to use the player for a
long time, be sure to disconnect the power
supply (AC power adapter or car battery
cord). To remove the AC power adaptor from
the wall outlet, grasp the plug itself; never
pull the cord.
On heat build-up
Heat may build up in the player if it is used for
an extended period of time. This, however, is
not a malfunction.
For driver's safety
Comply with your local traffic rules and
regulations.
While driving
— The driver must not watch or operate the
player. It may lead to distraction and
cause an accident.
— The driver must not use the headphones.
It may lead to distraction and cause an
accident.
Park the car in a safe place when the
driver watch and operate the player or use
the headphones.
Thank you for purchasing this Sony Portable
DVD Player. You can enjoy its various features
even more with:
DVD/Video CD/Audio CD playback.
Support DTS/Dolby Digital through optical
digital output terminal.
MP3/JPG file playback (recorded on CD-
ROMs/CD-Rs/CD-RWs).
Supplied controller accessory
Card remote commander
RM-X137
Before operating the player, please read this
operating instructions thoroughly and retain it
for future reference.
Copyrights
This product incorporates copyright protection
technology that is protected by method claims
of certain U.S. patents, other intellectual
property rights owned by Macrovision
Corporation, and other rights owners. Use of
this copyright protection technology must be
authorized by Macrovision Corporation, and is
intended for home and other limited viewing
uses only unless otherwise authorized by
Macrovision Corporation. Reverse engineering
or disassembly is prohibited.
Manufactured under license from Dolby
Laboratories. “Dolby”, “Pro Logic”, and the
double-D symbol are trademarks of Dolby
Laboratories.
“DTS,” “DTS Digital Surround” and “DTS
Digital Out” are trademarks of Digital Theater
Systems, Inc.
Welcome !
Polarity of
the plug
5
About this manual
Conventions
Instructions in this manual describe how to
use the player mainly by using the controls
on the supplied wireless card remote
commander.
The icons below are used in this manual:
While operating
— Do not insert your hands, fingers or
foreign objects into the player. It may
cause injury or damage to the player.
— Take extra care not to wind the wire of the
headphones around your neck avoiding
injury or suffocation in the event of a
sudden movement of the vehicle.
— Keep small articles out of the reach of
children.
If the player does not work, check the
connections first. If everything is in order,
check the fuse.
If your car was parked in direct sunlight,
allow the player to cool off before operating
it.
Avoid installing the player in places:
— subject to temperature below 0 °C (32 °F)
or above 45 °C (113 °F)
— subject to direct sunlight
— near heat sources (such as heaters)
— exposed to rain or moisture
— exposed to excessive dust or dirt
— subject to excessive vibration
— subject to heat:
Keep the player away from nearby hot
vehicle components that heat up over
time such as hoses, high current wires,
and braking systems components. Make
sure to leave enough room for ventilation
on openings and slots to protect from over
heating.
If you have any questions or problems
concerning the player, please consult your
nearest Sony dealer.
Moisture condensation
On a rainy day or in a very damp area,
moisture condensation may occur inside the
lenses. Should this occur, the player will not
operate properly. In such a case, remove the
disc and wait for about an hour until the
moisture has evaporated.
To maintain high sound quality
Be careful not to splash juice or other soft
drinks onto the player or discs.
Icon Meaning
Functions available for DVD
VIDEOs or DVD-Rs/DVD-RWs in
video mode
Functions available for Video CDs
or CD-Rs/CD-RWs in video CD
format
Functions available for music CDs
or CD-Rs/CD-RWs in music CD
format
Functions available for files in MP3
format stored on CD-ROMs/CD-
Rs/CD-RWs
Functions available for files in
JPEG format stored on CD-ROMs/
CD-Rs/CD-RWs
6
Region
code
About discs this player can
play
This player can play the following discs:
DVD
DVD-R
DVD-RW
Video CD
Audio CD
CD-R/CD-RW
Disc type Label on the disc
DVD Videos
Video CDs
Audio CDs
MP3 files/
JPEG files
“DVD VIDEO,” “DVD-R” and “DVD-RW” are
trademarks.
Notes on CD-Rs (recordable CDs)/
CD-RWs (rewritable CDs)/DVD-Rs
(recordable DVDs)/DVD-RWs
(rewritable DVDs)
Some CD-Rs/CD-RWs/DVD-Rs/DVD-RWs
(depending on the equipment used for its
recording or the condition of the disc) may
not play on this player.
•You cannot play a CD-R/CD-RW that is not
finalized*.
•You cannot play a CD-R/CD-RW that is
recorded in Multi Session.
•You can play MP3/JPEG files recorded on
CD-ROMs, CD-Rs, and CD-RWs.
* A process necessary for a recorded CD-R/CD-RW
disc to be played on the audio CD player.
Region code of DVDs this player
can play
This player has a region code printed on the
rear of the player and will only play DVDs that
are labeled with identical region codes. DVDs
labeled
ALL
will also be played on this player.
If you try to play any other DVD, the message
“REGION ERROR” will appear on the screen.
Depending on the DVD, the region code
indication may not appear even if the DVD is
prohibited by area restrictions.
Cautions
• This player CANNOT play these discs.
— DVD-Audio — DVD-RAM
— DVD-ROM — CD-G
— SVCD — CD-I
— Photo-CD — VSD
— Active-Audio (Data)
— CD-Extra (Data)
— Mixed CD (Data)
— CD-ROM (the data other than the MP3/JPEG
file)
— DVD-RW recorded in VR mode
• This product incorporates copyright protection
technology that is protected by method claims of
certain U.S. patents and other intellectual
property rights owned by Macrovision
Corporation and other rights owners. Use of this
copyright protection technology must be
authorized by Macrovision Corporation, and is
intended for home and other limited viewing
uses only unless otherwise authorized by
Macrovision Corporation. Reverse engineering or
disassembly is prohibited.
7
Note on PBC (Playback Control)
This player conforms to Ver. 1.1 and Ver. 2.0 of
Video CD standards. You can enjoy two kinds
of playback according to the disc type.
Disc type
Video CDs without
PBC functions
(Ver. 1.1 discs)
Video CDs with
PBC functions
(Ver. 2.0 discs)
Note on DTS-encoded CDs
When playing DTS*-encoded CDs, excessive
noise will be heard from the analog stereo
outputs. To avoid possible damage to the
audio system, the consumer should take
proper precautions when the analog stereo
outputs of this player are connected to an
amplification system. To enjoy DTS Digital
Surround™ playback, an external 5.1-channel
DTS Digital Surround™ decoder system must
be connected to the digital output of this
player.
* “DTS,” “DTS Digital Surround” and “DTS Digital
Out” are trademarks of Digital Theater Systems,
Inc.
Terms for discs
DVD structure
Disc
Title
Chapter
You can
Video playback (moving
pictures) as well as music.
• Interactive software
with menu screens
displayed on the
monitor
(PBC Playback, page
20).
• Video playback
functions.
• High-resolution still
pictures if they are
included on the disc.
Video CD/Audio CD structure
Title
The longest section of a picture or music
feature on a DVD, e.g., a movie for video
software, or an album for audio software, etc.
Chapter
Sections of a picture or a music feature that
are smaller than titles. A title is composed of
several chapters. Each chapter is assigned a
chapter number enabling you to locate the
chapter you want. Depending on the disc,
chapters may not be recorded.
Track
Sections of a picture or a music feature on a
Video CD/Audio CD. Each track is assigned
a track number enabling you to locate the
track you want.
Scene
On a Video CD with PBC (playback control)
functions, the menu screens, moving pictures
and still pictures are divided into sections
called “scenes.” Each scene is assigned a
scene number enabling you to locate the
scene you want.
Track
Disc
8
Connection
On AUDIO/VIDEO OUTPUT
connectors
You can connect a TV to the AUDIO/VIDEO
OUTPUT connectors to output the contents
being played back on the player. Connect the
yellow plugs of the audio/video cable to the
video connectors on both the TV and the
player and connect the white plugs and the red
plugs to the white (left audio) connectors and
red (right audio) connectors respectively.
On AUDIO/VIDEO INPUT connectors
You can connect a VTR, etc. to the AUDIO/
VIDEO INPUT connectors to input the
contents being played back on the device. You
can connect the device in the same way as
described on “On AUDIO/VIDEO OUTPUT
connectors” above.
Optical cable
(not supplied)
To a digital
amplifier, etc.
AUDIO/VIDEO INPUT OPTICAL OUTPUT
DC IN 12V
AUDIO/VIDEO OUTPUT
Two headphones
connectors
(at the side)
AC power
adaptor
(supplied)
Audio/video
cable
(not supplied)
Antenna for FM
transmission
(supplied)
Power cord for the
cigar lighter socket
(supplied)
TV, etc.
To audio/video
input connectors
To the cigar lighter socket
When using the
player in the car
To a
wall
outlet
Notes
• When connecting the other device to the player,
be sure to connect the player to the power
source after all other connections are completed.
• If an obstacle such as cigar ash is caught inside
the cigar lighter socket, the contact between the
power cord plug and the socket becomes
incomplete and the plug may get extremely hot
during use. To avoid this, check the socket and
clean it if necessary before connecting the power
cord.
* Polarity of the plug
This player is supplied with two types of
power cable. When you use the player in the
car, connect the player to the cigar lighter
socket; when using at home, connect it to the
AC outlet.
*
AC power cord
(supplied)
9
Installing the player in the car
The player can be installed in the car by using
the supplied mounting straps.
1 Attach the angled hook on each of the
supplied mounting straps to the four
brackets at the bottom of the player.
2 Attach the round hooks to the car.
Be sure to hook the player to steady objects
such as the headrest shafts of the seat or the
seat rails.
When you attach the player to the center
console, secure the round hooks to the
bottom edge of the console.
3 Take in the slack of the belts to secure
the player.
Example when the player is attached behind
the seat
Example when the player is attached between
the seats
Example when the player is attached to the
center console
When the player is attached to the center console
• When picture noise appears or the sound
dropouts occur due to vibrations from the car,
place a cushioning material under the player.
• If a gap exists between the top of the center
console and the bottom of the player, fill the
gap with a material with optimum thickness so
that the player becomes stable.
continue to next page t
To the car
To the player
Round hook Angled hook
10
REVERSE
Resetting the player
Before operating the player for the first time,
you must reset the player.
Press (RESET) with a pointed object, such as a
ballpoint pen. Pushing it with force by using a
needle may damage the player.
Notes
• When you press (RESET), some of the previous
settings may be lost. If this occurs, make the
settings again.
• It takes about 10 seconds for the player to reset
itself after pressing (RESET). Do not insert a disc
during this time. If you do, the player may not be
reset properly.
RESET
When the player is installed behind
the seat or between the seats
The player is installed upside down.
Do the procedure below to turn the picture on
the screen upside down and switch the audio
channels to use the player.
1 Open the monitor of the player, rotate it
in 180 degrees, then close it with the
screen facing upward.
2 Turn on the player, then press
(REVERSE) on the monitor.
To cancel this, press (REVERSE) again.
11
MV-65ST
D
IS
C
IN
R
E
S
E
T
6
7
8
9
0
qa
qd
qs
qf
qg
Refer to the pages listed for details.
1 Monitor
2 VOL –/+ buttons 13, 27
To turn up or down the volume or to select
the item during menu operation.
3 Disc slot
4 DISC IN light
When a disc is in the player, the DISC IN
light glows orange.
5 POWER (on/off) button 13
To turn on/off the player.
6 u (play/pause) button 13, 14, 15, 20
7 x (stop) button 14, 15
8 . (previous)/> (next) buttons 14,
20
9 Receptor for the card remote
commander
q; Reverse button 10, 30
To switch images upside down and
reverse the output of the audio channels.
qa Speakers (left/right)
qs MENU button 27
To make various display settings and FM
transmitter setting.
qd HEADPHONES jacks
To connect the headphones. 2 sets of
headphones can be connected.
qf Z (eject) button 14
Available to eject a disc from the player
even when the player is turned off.
qg RESET button 10
Note
Even when the player is turned off by pressing
(POWER), you can eject a disc from the player,
though you cannot insert a disc.
continue to next page t
Location of controls
12
Card remote commander RM-X137
ENTER
SEARCH
POWER
DISPLAY
CLEAR
SETUP
AUDIO
ANGLE
SUBTITLE
MENU
TOP MENU
INPUT
123
456
7890
VOL
Refer to the pages listed for details.
1 DISPLAY button 16
To display the time information of the disc.
2 Number buttons (0 to 9) 14, 20, 24
3 TOP MENU button 18
To display the top menu of a recorded
DVD.
4 MENU button 18, 20
To display the recorded DVD menu, or to
turn on/off the PBC (Playback control)
menu of a Video CD.
5 O (return) button 20
6 ./> (previous/next) buttons 14, 20
7 m (fast reverse)/
M (fast forward) buttons 14
8 M/,/m/< buttons 14, 15, 18, 21
9 POWER (on/off) button 13
To turn on/off the player.
q; SEARCH button 14
To specify a desired point on a disc by
chapter, title, or track.
qa CLEAR button
qs SUBTITLE button 17
To change the subtitle language while
playing a DVD.
qd ENTER button 14, 21
To enter a setting.
qf ANGLE button 19
To select the multiple angles of view while
playing a DVD.
qg AUDIO button 19
To change the audio output/audio
language.
qh (slow reverse)/y (slow forward)
buttons 14
qj u (play/pause) button 13, 14, 15, 20
qk x (stop) button 14, 15
ql SETUP button 22
Used to perform menu operations.
w; INPUT button 26
To select the input source.
wa VOL (–/+) buttons 13, 27
To turn up or down the volume.
The corresponding buttons of the card
remote commander control the same
functions as those on the player.
Instructions in this manual describe how to use
the player by mainly using the card remote
commander.
Tip
Refer to “Replacing the lithium battery of the card
remote commander” for details on how to replace
the battery (page 31).
13
Various Playback
This chapter describes various functions for
playback.
Playing a disc
ENTER
SEARCH
POWER
DISPLAY
CLEAR
SETUP
AUDIO
ANGLE
SUBTITLE
MENU
TOP MENU
INPUT
123
456
7890
VOL
./>
u
x
POWER
SEARCH
M/m
</,
/y
m/M
VOL
1 Open the monitor and adjust the tilt and
swivel.
2 Press (POWER) to turn on the player.
The monitor turns on and the green light of
the POWER switch on the player lights up.
Number
buttons
3 Insert the disc (labeled side up) into the
player.
Playback starts automatically.
If a disc is already inserted or playback does
not start automatically, press u to start
playback.
4 Press (VOL) (+) or (VOL) (–) on the card
remote commander to adjust the
volume.
To turn off the power
Press (POWER) so that the green light of the
POWER switch on the player turns off.
After use
Turn off the player and disconnect the power
cord from the power source.
Note on using the player in the car
Using the player while the ignition key is in
ACC position and the engine is stopped may
cause the car battery to run down.
Notes
Even when the player is turned off, you can eject
a disc from the player, though you cannot insert
a disc.
Read the instruction manual supplied with the
disc to play with this player.
When you play an 8-cm disc (e.g., CD-single), be
sure to insert it to the center area of the disc slot.
Depending on the recording method used on the
disc, it may take a minute or more before
playing.
Depending on the condition of the disc, it may
not play back (page 32).
A high-bit rate MP3 file such as 320 kbps may not
play back properly.
continue to next page t
14
Operation for playback
To Do this
Stop playback Press x*
1
Eject the disc Press Z on the
player.
Pause Press u *
2
.
Press again to
resume playback.
Go to the next chapter, Press >
track, or scene
Go back to the preceding Press .
chapter, track, or scene
Fast forward/ Press M/m while
fast reverse playing*
3
*
4
Each press changes
the playback speed
as follows: 2 times
normal speed
t 4 times normal
speed t 8 times
normal speed t 16
times normal speed
t 32 times normal
speed t normal
playback speed.
Slow forward Press y/ while
(DVD/Video CD only)/ playing
*
4
Slow reverse Each press changes
(DVD only) the playback speed
as follows: 1/2 times
normal speed t 1/4
times normal
speedt 1/8 times
normal speedt 1/
16 times normal
speedt 1/32 times
normal speedt
normal playback
speed.
*
1
If the resume playback function is activated, you
can resume playback later by pressing u. For
details, see “Resume playback” (page 15).
*
2
DVD/Video CD/Audio CD/MP3/JPEG
X” is displayed on the screen.
*
3
DVD/Video CD/Audio CD/MP3/JPEG
No sound is output during fast forward or fast
reverse.
*
4
A disc other than a DVD returns to normal
playback when a track/MP3 file finishes.
Searching a chapter/title/track
directly
1 During playback or pause, press
(SEARCH) to display search screen.
•DVD*
1
Each time you press (SEARCH), the
search screen changes as follows: “TIME
SEARCH,” “SELECT TITLE,” and “OFF.”
When you press < or , button while
“SELECT TITLE” is displayed in the
screen, the screen toggles between
“SELECT CHAPTER” and “SELECT
TITLE.”
•Video CD (only when PBC is off)/Audio
CD*
2
Each time you press (SEARCH), the
search screen toggles between “TIME
SEARCH” and “SELECT TRACK.”
2 Press the number buttons to enter the
desired chapter/title/track number.
When “TIME SEARCH” is displayed
When “SELECT TITLE,” “SELECT CHAPTER,” or
“SELECT TRACK” is displayed
3 Press (ENTER).
*
1
Search is possible even while the player is
stopped.
*
2
You can use the number buttons on the card
remote commander to select the track.
Note
You cannot set “0.”
15
Resume playback
You can resume playback from the point
where the playback has been stopped. The
player memorizes the point even after the
power is turned off.
1 During playback, press x to stop.
The player memorizes the point where
playback is stopped.
•DVD/Video CD/Audio CD
“PRESS PLAY KEY TO LASTPLAY”
appears on the screen.
2 Press u to start playback.
“LASTPLAY” appears on the screen and
playback starts from the point where
playback has been stopped.
•MP3/JPEG
When resume playback is activated,
playback starts from the beginning of the
MP3/JPEG file (track) during which you
have stopped playback.
Notes
• To deactivate the resume function, press x again
while playback is stopped. “PRESS PLAY KEY TO
PLAY” appears on the screen at this time.
• The resume function will be deactivated when
the disc is ejected.
• The resume function will also be deactivated
when the ignition key is turned to OFF position
or when the player is disconnected from the
power source.
Using MP3/JPG menu
When you insert a disc containing MP3 or
JPEG files, playback automatically starts and
the MP3/JPG menu appears on the screen.
To make settings on the MP3/JPG menu, press
x to stop the player.
To select a folder or a file
While the player is stopped, use M/m buttons
to select the folder or a file, then press
(ENTER).
When you press (ENTER) after selecting a
folder, files inside the folder appear.
To select the display mode
While the player is stopped, use ,/<
buttons to select “DISPLAY,” then press
(ENTER) repeatedly to select the display
mode.
Each time you press (ENTER), display mode
changes as follows: MP3 ONLY (only MP3
files are displayed) t JPG ONLY (only JPEG
files are displayed) t MP3 AND JPG (MP3
files and JPEG files are grouped and
displayed).
To select the playback mode
While the player is stopped, use ,/</m
buttons to select “PLAYMODE,” then press
(ENTER) repeatedly to select the playback
mode.
Each time you press (ENTER), playback mode
changes as follows: REPEAT DISC (repeats all
the tracks on the disc) t NORMAL (normal
playback) t REPEAT DIR (repeats all the
tracks within the directory) t REPEAT ONE
(repeats one track) t RANDOM (plays tracks
at random; the same track may be played more
than once) t SHUFFLE (plays tracks at
random; tracks are played only once).
continue to next page t
16
Displaying elapsed time
You can display the elapsed time and the
remaining time of DVDs, Video CDs and
Audio CDs.
ENTER
SEARCH
POWER
DISPLAY
CLEAR
SETUP
AUDIO
ANGLE
SUBTITLE
MENU
TOP MENU
INPUT
123
456
789
0
VOL
DISPLAY
During playback, press (DISPLAY).
The elapsed time or the remaining time is
displayed at the upper left.
Each time you press (DISPLAY), the display
changes as follows:
DVD
Elapsed time of the title
Remaining time of the title
Elapsed time of the chapter
Remaining time of the chapter
OFF (default display)
Notes
• While playing back, you cannot change a folder
or file with the MP3/JPG menu. Only the files in
the selected folder can be selected with the ./
> button. To change the folder, stop playback.
• Names for the MP3 folders and files are
displayed properly when they consist of
alphabets, numbers, or symbols only. Folders and
files containing other characters are displayed as
“DIR--001” or “FILEOPEN--001.”
17
Video CD
Audio CD
To turn off the time information
Press (DISPLAY) repeatedly to select “OFF.”
Elapsed time of the disc
Elapsed time of the track and audio
mode (stereo/mono)
Elapsed time of the track and PBC
setting (ON/OFF)
Remaining time of the track
OFF (default display)
Changing the subtitle
language
Some DVDs have recorded subtitles in one or
more languages. You can turn the subtitles on
or off, or change the subtitle language on such
DVDs.
ENTER
SEARCH
POWER
DISPLAY
CLEAR
SETUP
AUDIO
ANGLE
SUBTITLE
MENU
TOP MENU
INPUT
123
456
789
0
VOL
SUBTITLE
Press (SUBTITLE) during playback.
The subtitle language is displayed at the
upper left.
Example: a subtitle language display
Each time you press (SUBTITLE), the
language switches within the list of subtitle
languages recorded on the disc.
To turn off the subtitle
Press (SUBTITLE) repeatedly to select “OFF.”
Notes
• You can also change the subtitle languages by
changing Setup*.
See “Displaying the subtitles
for DVD — SUBTITLE” (page 23).
*
You can change to a specific subtitle language
using the DVD SETUP menu, only if the
language is included in both the disc and the
menu. In some discs, the initial language to be
displayed is specified regardless of the DVD
SETUP menu setting.
• This function varies or may not work, depending
on the DVD.
The disc contains 2
subtitle languages and
the first language is
currently selected.
Remaining time of the disc
Elapsed time of the disc
OFF
Elapsed time of the track
(default display)
18
Using the MENU button
Some DVDs have more comprehensive menu
that includes such things as the audio
languages, subtitle languages, titles, and
chapters, etc.
1 During a DVD playback, press (MENU).
The DVD menu is displayed.
2 Press M/,/m/< to select the desired
item.
3 Press (ENTER).
If additional selection screens appear,
repeat step 2 and 3.
Notes
• Some DVDs do not have a DVD menu and on
some DVDs, the contents of the DVD menu and
title menu are the same.
• On some DVDs, “DVD Menu” may be expressed
as “MENU.”
• On some DVDs, “Press ENTER” may be expressed
as “Press SELECT” in step 3.
• The contents of the DVD menu differ, depending
on the DVD.
• Read the instruction manual supplied with a
DVD.
Using a DVD menu
With some DVDs you can use the original
menu such as Title menu and DVD menu. In
title menu, you can play your favorite scene or
song by selecting titles of songs and scenes.
You can select an item, subtitle language,
audio language etc. by selecting a DVD menu.
The contents of title menus and DVD menus
differ, depending on the DVD. There may be
some DVDs which have no recorded menus.
ENTER
SEARCH
POWER
DISPLAY
CLEAR
SETUP
AUDIO
ANGLE
SUBTITLE
MENU
TOP MENU
INPUT
123
456
7890
VOL
TOP MENU
MENU
ENTER
M/m
</,
Using the TOP MENU button
Some DVDs have a title menu. From the title
menu you can select a title for playback. Titles
are the longest sections of a picture or music
feature on a DVD, e.g., a movie, or an album
for audio software, etc. The TOP MENU
button is available to display the initial menu
screen.
1 During DVD playback, press (TOP MENU).
The title menu* (top menu) is displayed.
*
The contents of the title menu differ,
depending on the DVD.
2 Press M/,/m/< to select the desired
title.
3 Press (ENTER).
The title you selected starts to play.
19
Changing the audio
language
Some DVDs have multiple audio languages
you can choose from.
ENTER
SEARCH
POWER
DISPLAY
CLEAR
SETUP
AUDIO
ANGLE
SUBTITLE
MENU
TOP MENU
INPUT
123
456
789
0
VOL
AUDIO
During playback, press (AUDIO)
repeatedly to select the desired audio
language.
The current audio language is displayed at
the upper left.
Example: an audio language display
When the display for the language code
appears, input the language code
corresponding to the desired language
(page 37).
Notes
• You can switch the audio language only if
multiple audio languages are recorded on the
DVD.
• You can also change the audio languages by
using the DVD menu (page 18) or the DVD SETUP
menu* (page 22).
* You can change to a specific audio language
using the DVD SETUP menu, only if the
language is included in both the disc and the
menu. In some discs, the initial language to be
output is specified regardless of the DVD SETUP
menu setting.
• This function varies or may not work, depending
on the DVD.
The format of the sound source
(Dolby D, DTS, or LPCM) may appear.
Changing angles
Some DVDs have multiple alternative angles
recorded for certain scenes. If you have set
“ANGLE MARK” to “ON” (page 23), a notice
appears at the scene.
ENTER
SEARCH
POWER
DISPLAY
CLEAR
AUDIO
ANGLE
SUBTITLE
MENU
TOP MENU
INPUT
123
456
789
0
VOL
SETUP
ANGLE
1 During playback of a DVD having
multiple alternative angles recorded,
press (ANGLE) when a notice appears.
The number of the currently selected angle
is displayed at the upper right.
2 Press (ANGLE) repeatedly to select your
favorite angle number, while the angle
number is displayed.
Each time you press (ANGLE), the angle
number switches.
Notes
• You can switch the angle only if multiple angles
are recorded on the DVD.
• The total number of recorded angles differs
depending on the DVD and scene.
• You can switch the angle only during normal
playback. You cannot switch the angle during
fast forward/reverse playback.
• When the selected scene with multi angles
appears, the angle is automatically switched to
the angle number you selected in step 2.
• This function varies or may not work, depending
on the DVD.
The angle number you
have currently selected/
the total number of
multiple alternative
angles
20
Using the PBC (playback
control) function
During playback of a PBC compatible Video
CD, you can display the PBC menu and select
the item from the menu.
ENTER
SEARCH
POWER
DISPLAY
CLEAR
SETUP
AUDIO
ANGLE
SUBTITLE
MENU
TOP MENU
INPUT
123
456
7890
VOL
MENU
./>
u
O
1 Insert a Video CD, then press
(MENU) repeatedly to select “PBC ON.”
Depending on the Video CD, the PBC menu
may be displayed automatically after
inserting a Video CD.
Each time you press (MENU), the PBC
menu function turns on or off.
2 Press u.
The PBC menu is displayed.
3 While the PBC menu screen is displayed;
— press the number buttons to select the
number of the desired item.
— press ./> to go to the previous/
next page.
Button functions vary or may not work,
depending on the Video CD.
Notes
• To display the PBC menu during playback of a
Video CD, press (MENU) repeatedly to select
“PBC ON,” then press u.
• During playback of a Video CD with “PBC ON,”
press ./> to change the item. The PBC
menu is not displayed but the item you selected
starts to play.
• During playback of a Video CD with “PBC ON,”
press O to display the PBC menu and the B
mark.
• The PBC menus differ, depending on the Video
CD. Read the instruction manual supplied with
the Video CD.
Changing the audio output
You can select the desired audio output from
“STEREO” or “L-MONO/R-MONO” during
Video CD or Audio CD playback.
ENTER
SEARCH
POWER
DISPLAY
CLEAR
SETUP
AUDIO
ANGLE
SUBTITLE
MENU
TOP MENU
INPUT
123
456
789
0
VOL
AUDIO
1 During playback, press (AUDIO).
The current output is displayed at the
upper left.
Example: an audio output display
L-MONO
2 Press (AUDIO) to select the desired
output from “STEREO” or “L-MONO/R-
MONO” while the output is displayed.
Each time you press (AUDIO), the output
switches.
Number
buttons
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16
  • Page 17 17
  • Page 18 18
  • Page 19 19
  • Page 20 20
  • Page 21 21
  • Page 22 22
  • Page 23 23
  • Page 24 24
  • Page 25 25
  • Page 26 26
  • Page 27 27
  • Page 28 28
  • Page 29 29
  • Page 30 30
  • Page 31 31
  • Page 32 32
  • Page 33 33
  • Page 34 34
  • Page 35 35
  • Page 36 36
  • Page 37 37
  • Page 38 38
  • Page 39 39
  • Page 40 40
  • Page 41 41
  • Page 42 42
  • Page 43 43
  • Page 44 44
  • Page 45 45
  • Page 46 46
  • Page 47 47
  • Page 48 48
  • Page 49 49
  • Page 50 50
  • Page 51 51
  • Page 52 52
  • Page 53 53
  • Page 54 54
  • Page 55 55
  • Page 56 56
  • Page 57 57
  • Page 58 58
  • Page 59 59
  • Page 60 60
  • Page 61 61
  • Page 62 62
  • Page 63 63
  • Page 64 64
  • Page 65 65
  • Page 66 66
  • Page 67 67
  • Page 68 68
  • Page 69 69
  • Page 70 70
  • Page 71 71
  • Page 72 72
  • Page 73 73
  • Page 74 74
  • Page 75 75
  • Page 76 76
  • Page 77 77
  • Page 78 78
  • Page 79 79
  • Page 80 80
  • Page 81 81
  • Page 82 82
  • Page 83 83
  • Page 84 84
  • Page 85 85
  • Page 86 86
  • Page 87 87
  • Page 88 88
  • Page 89 89
  • Page 90 90
  • Page 91 91
  • Page 92 92
  • Page 93 93
  • Page 94 94
  • Page 95 95
  • Page 96 96
  • Page 97 97
  • Page 98 98
  • Page 99 99
  • Page 100 100
  • Page 101 101
  • Page 102 102
  • Page 103 103
  • Page 104 104
  • Page 105 105
  • Page 106 106
  • Page 107 107
  • Page 108 108
  • Page 109 109
  • Page 110 110
  • Page 111 111
  • Page 112 112

Sony AK8MV65STF Manuel utilisateur

Catégorie
Lecteur CD
Taper
Manuel utilisateur
Ce manuel convient également à

dans d''autres langues