Allen-Bradley ControlLogix 1756-OX8I Installation Instructions Manual

Marque: Allen-Bradley

Modèle: ControlLogix 1756-OX8I

Taper: Installation Instructions Manual

Publication 1756-IN513D-EN-P - November 2003

Installation Instructions

ControlLogix AC (10-265V) DC (5-150V) Isolated

Relay Module

Catalog Number 1756-OX8I

Obtain a User Manual

This product also has a user manual (pub. no. 1756-UM058). To view

it, visit www.ab.com/manuals

or www.theautomationbookstore.com.

To purchase a manual, you can:

• contact your distributor or Rockwell Automation representative

• visit www.theautomationbookstore.com

and place an order

• call 800.963.9548 (USA/Canada) or 001.320.725.1574 (outside

USA/Canada)

To: See page:

Identify the Module Components 7

Note the Power Requirements 7

Install the Module 8

Key the Module and Removable Terminal Block/Interface Module 9

Wire the Removable Terminal Block 10

Wire the Module 11

Assemble the Removable Terminal Block and the Housing 12

Install the Removable Terminal Block onto the Module 12

Check the Indicators 13

Remove the Removable Terminal Block from the Module 14

Remove the Module 14

See Specifications 15

Allen-Bradley Parts

2 ControlLogix AC (10-265V) DC (5-150V) Isolated Relay Module

Publication

1756-IN513D-EN-P - November 2003

Important User Information

Solid state equipment has operational characteristics differing from those of electromechanical

equipment. Safety Guidelines for the Application, Installation and Maintenance of Solid State Controls

(Publication SGI-1.1 available from your local Rockwell Automation sales office or online at

http://www.ab.com/manuals/gi) describes some important differences between solid state equipment

and hard-wired electromechanical devices. Because of this difference, and also because of the wide

variety of uses for solid state equipment, all persons responsible for applying this equipment must

satisfy themselves that each intended application of this equipment is acceptable.

In no event will Rockwell Automation, Inc. be responsible or liable for indirect or consequential damages

resulting from the use or application of this equipment.

The examples and diagrams in this manual are included solely for illustrative purposes. Because of the

many variables and requirements associated with any particular installation, Rockwell Automation, Inc.

cannot assume responsibility or liability for actual use based on the examples and diagrams.

No patent liability is assumed by Rockwell Automation, Inc. with respect to use of information, circuits,

equipment, or software described in this manual.

Reproduction of the contents of this manual, in whole or in part, without written permission of Rockwell

Automation, Inc. is prohibited.

Throughout this manual we use notes to make you aware of safety considerations.

WARNING

Identifies information about practices or circumstances that can cause an explosion in a

hazardous environment, which may lead to personal injury or death, property damage,

or economic loss.

IMPORTAN

Identifies information that is critical for successful application and understanding of the

product.

ATTENTION

Identifies information about practices or circumstances that can lead to personal injury

or death, property damage, or economic loss. Attentions help you:

• identify a hazard

• avoid a hazard

• recognize the consequence

SHOCK HAZAR

Labels may be located on or inside the drive to alert people that dangerous voltage may

be present.

BURN HAZARD

Labels may be located on or inside the drive to alert people that surfaces may be

dangerous temperatures.

ControlLogix AC (10-265V) DC (5-150V) Isolated Relay Module 3

Publication

1756-IN513D-EN-P - November 2003

Environment and Enclosure

Prevent Electrostatic Discharge

ATTENTION

This equipment is intended for use in a Pollution Degree 2 industrial environment, in

overvoltage Category II applications (as defined in IEC publication 60664-1), at altitudes

up to 2000 meters without derating.

This equipment is considered Group 1, Class A industrial equipment according to

IEC/CISPR Publication 11. Without appropriate precautions, there may be potential

difficulties ensuring electromagnetic compatibility in other environments due to

conducted as well as radiated disturbance.

This equipment is supplied as "open type" equipment. It must be mounted within an

enclosure that is suitably designed for those specific environmental conditions that will

be present and appropriately designed to prevent personal injury resulting from

accessibility to live parts. The interior of the enclosure must be accessible only by the

use of a tool. Subsequent sections of this publication may contain additional

information regarding specific enclosure type ratings that are required to comply with

certain product safety certifications.

NOTE: See NEMA Standards publication 250 and IEC publication 60529, as applicable,

for explanations of the degrees of protection provided by different types of enclosure.

Also, see the appropriate sections in this publication, as well as the Allen-Bradley

publication 1770-4.1 ("Industrial Automation Wiring and Grounding Guidelines"), for

additional installation requirements pertaining to this equipment.

ATTENTION

This equipment is sensitive to electrostatic discharge, which can cause internal

damage and affect normal operation. Follow these guidelines when you handle this

equipment:

• Touch a grounded object to discharge potential static.

• Wear an approved grounding wriststrap.

• Do not touch connectors or pins on component boards.

• Do not touch circuit components inside the equipment.

• If available, use a static-safe workstation.

• When not in use, store the equipment in appropriate static-safe packaging.

Allen-Bradley Parts

4 ControlLogix AC (10-265V) DC (5-150V) Isolated Relay Module

Publication

1756-IN513D-EN-P - November 2003

Removal and Insertion Under Power

Be sure that power is removed or the area is nonhazardous before

proceeding. Repeated electrical arcing causes excessive wear to

contacts on both the module and its mating connector. Worn contacts

may create electrical resistance that can affect module operation.

European Hazardous Location Approval

If you install the module in a European Zone 2 location, consider:

WARNING

When you insert or remove the module while backplane

power is on, an electrical arc can occur. This could cause

an explosion in hazardous location installations.

European Zone 2 Certification (The following applies when the product bears the

EEx Marking)

This equipment is intended for use in potentially explosive atmospheres as defined by

European Union Directive 94/9/EC.

The LCIE (Laboratoire Central des Industries Electriques) certifies that this equipment has

been found to comply with the Essential Health and Safety Requirements relating to the

design and construction of Category 3 equipment intended for use in potentially explosive

atmospheres, given in Annex II to this Directive. The examination and test results are

recorded in confidential report No. 28 682 010.

Compliance with the Essential Health and Safety Requirements has been assured by

compliance with EN 50021.

IMPORTANT

When using this product, also consider the following:

• This equipment is not resistant to sunlight or other sources of UV

radiation.

• The secondary of a current transformer shall not be

open-circuited when applied in Class I, Zone 2 environments.

• Equipment of lesser Enclosure Type Rating must be installed in

an enclosure providing at least IP54 protection when applied in

Class I, Zone 2 environments.

• This equipment shall be used within its specified ratings defined

by Allen-Bradley.

• Provision shall be made to prevent the rated voltage from being

exceeded by transient disturbances of more than 40% when

applied in Class I, Zone 2 environments.

ControlLogix AC (10-265V) DC (5-150V) Isolated Relay Module 5

Publication

1756-IN513D-EN-P - November 2003

North American Hazardous Location Approval

The following information applies

when operating this equipment in

hazardous locations:

Informations sur l’utilisation de cet

équipement en environnements

dangereux:

Products marked “CL I, DIV 2, GP A, B, C,

D” are suitable for use in Class I Division 2

Groups A, B, C, D, Hazardous Locations

and nonhazardous locations only. Each

product is supplied with markings on the

rating nameplate indicating the hazardous

location temperature code. When

combining products within a system, the

most adverse temperature code (lowest

“T” number) may be used to help

determine the overall temperature code of

the system. Combinations of equipment in

your system are subject to investigation

by the local Authority Having Jurisdiction

at the time of installation.

Les produits marqués "CL I, DIV 2, GP A, B, C, D"

ne conviennent qu’à une utilisation en

environnements de Classe I Division 2 Groupes

A, B, C, D dangereux et non dangereux. Chaque

produit est livré avec des marquages sur sa

plaque d’identification qui indiquent le code de

température pour les environnements

dangereux. Lorsque plusieurs produits sont

combinés dans un système, le code de

température le plus défavorable (code de

température le plus faible) peut être utilisé pour

déterminer le code de température global du

système. Les combinaisons d’équipements

dans le système sont sujettes à inspection par

les autorités locales qualifiées au moment de

l’installation.

Allen-Bradley Parts

6 ControlLogix AC (10-265V) DC (5-150V) Isolated Relay Module

Publication

1756-IN513D-EN-P - November 2003

WARNING

EXPLOSION HAZARD

• Do not disconnect

equipment unless

power has been

removed or the area

is known to be

nonhazardous.

• Do not disconnect

connections to this

equipment unless

power has been

removed or the area

is known to be

nonhazardous.

Secure any external

connections that

mate to this

equipment by using

screws, sliding

latches, threaded

connectors, or other

means provided

with this product.

• Substitution of

components may

impair suitability for

Class I, Division 2.

• If this product

contains batteries,

they must only be

changed in an area

known to be

nonhazardous.

AVERTISSEMENT

RISQUE D’EXPLOSION

• Couper le courant ou

s’assurer que

l’environnement est

classé non dangereux

avant de débrancher

l'équipement.

• Couper le courant ou

s'assurer que

l’environnement est

classé non dangereux

avant de débrancher

les connecteurs. Fixer

tous les connecteurs

externes reliés à cet

équipement à l'aide

de vis, loquets

coulissants,

connecteurs filetés ou

autres moyens fournis

avec ce produit.

• La substitution de

composants peut

rendre cet équipement

inadapté à une

utilisation en

environnement de

Classe I, Division 2.

• S’assurer que

l’environnement est

classé non dangereux

avant de changer les

piles.

The following information applies

when operating this equipment in

hazardous locations:

Informations sur l’utilisation de cet

équipement en environnements

dangereux:

ControlLogix AC (10-265V) DC (5-150V) Isolated Relay Module 7

Publication

1756-IN513D-EN-P - November 2003

Identify the Module Components

You received the following components with your order:

• 1756-OX8I module

• Removable Terminal Block (RTB) door label

If you did not receive these components, contact your local

distributor Rockwell Automation sales office.

This module mounts in a 1756 chassis and uses a separately-ordered

RTB or a Bulletin 1492 Interface Module (IFM)

(1)

to connect all

field-side wiring. This module uses one of the following RTBs:

• 1756-TBCH 36 position Cage clamp RTB

• 1756-TBS6H 36 position Spring clamp RTB

Use an extended-depth cover (1756-TBE) for applications with heavy

gauge wiring or requiring additional routing space. When using an

IFM, consult the documentation that came with it to connect wiring.

Note the Power Requirements

This module receives power from the 1756 chassis power supply and

requires 2 sources of power from the ControlLogix backplane:

• 100mA at 5.1V dc

• 100mA at 24V dc

Add this current/power value (2.9W) to the requirements of all other

modules in the chassis to prevent overloading the power supply.Field

output supply power should be limited to 10KVA available short

circuit power.

(1)

The ControlLogix system has been agency certified using the only the ControlLogix RTBs (i.e.

1756-TBCH, 1756-TBNH 1756-TBSH and 1756-TBS6H). Any application that requires agency

certification of the ControlLogix system using other wiring termination methods may require

application specific approval by the certifying agency.

IMPORTANT

Before you install your module, you should:

• install and ground a 1756 chassis and power supply.

• order and receive an RTB or IFM, and its

components, for your application.

Allen-Bradley Parts

8 ControlLogix AC (10-265V) DC (5-150V) Isolated Relay Module

Publication

1756-IN513D-EN-P - November 2003

Install the Module

You can install or remove the module while chassis power is applied.

Be sure that power is removed or the area is nonhazardous before

proceeding. Repeated electrical arcing causes excessive wear to

contacts on both the module and its mating connector. Worn contacts

may create electrical resistance that can affect module operation.

1. Align the circuit board with the top and bottom chassis guides.

2. Slide the module into chassis until module locking tabs click.

WARNING

When you insert or remove the module while backplane

power is on, an electrical arc can occur. This could cause

an explosion in hazardous location installations.

20861–M

Printed

Circuit

Board

Locking tab

ControlLogix AC (10-265V) DC (5-150V) Isolated Relay Module 9

Publication

1756-IN513D-EN-P - November 2003

Key the Module and Removable Terminal Block/Interface Module

Use the wedge-shaped keying tabs and U-shaped keying bands to

prevent connecting the wrong wires to your module.

Key positions on the module that correspond to unkeyed positions

on the RTB. For example, if you key the first position on the module,

leave the first position on the RTB unkeyed.

1. To key the module, insert the U-shaped band, as shown.

2. Push the band until it snaps in place.

3. To key the RTB or IFM, insert the wedge-shaped tab with

rounded edge first, as shown.

4. Push the tab until it stops.

Reposition the tabs to rekey future module applications.

20850–M

U-shaped

bands

20851–M

Wedge-shaped tab

Allen-Bradley Parts

10 ControlLogix AC (10-265V) DC (5-150V) Isolated Relay Module

Publication

1756-IN513D-EN-P - November 2003

Wire the Removable Terminal Block

Wire the RTB with a 1/8 inch (3.2mm) maximum flat-bladed

screwdriver before installing it onto the module.

Be sure that power is removed or the area is nonhazardous before

proceeding.

WARNING

When you connect or disconnect the Removable

Terminal Block (RTB) while field side power is on, an

electrical arc can occur. This could cause an explosion in

hazardous location installations.

Spring Clamp RTB Cage Clamp RTB

20860-M

20859-M

1. Strip 7/16 inch (11mm) maximum

length of wire.

2. Insert the screwdriver into the

inner hole of the RTB.

3. Insert the wire into the

open terminal and

remove the screwdriver.

1. Strip 3/8 inch (9.5mm) maximum

length of wire.

2. Insert the wire into the open terminal.

3. Turn the screw clockwise to close the

terminal on the wire.

ControlLogix AC (10-265V) DC (5-150V) Isolated Relay Module 11

Publication

1756-IN513D-EN-P - November 2003

Wire the Module

You can only connect wiring to your module with an RTB or IFM.

After completing field-side wiring, secure the wires in the strain relief

area with a cable-tie.

910

1112

1314

1516

1718

1920

2122

2324

2526

2728

2930

3132

3334

3536

30241-M

Non-isolated

wiring

Isolated wiring

Daisy chain to other RTBs

1756-OX8I

L1-0

L1-1

L1-4

L1-2

L1-3

L1-4

L1-5

L1-6

L1-7

Not used

OUT-0 N.C.

OUT-0 N.O.

OUT-1 N.C.

OUT-1 N.O.

OUT-4 N.C.

OUT-2 N.C.

OUT-2 N.O.

OUT-3 N.C.

OUT-3 N.O.

Not used

OUT-4 N.O.

OUT-5 N.C.

OUT-5 N.O.

OUT-6 N.C.

OUT-6 N.O.

OUT-7 N.C.

OUT-7 N.O

Not used

Jumper bar – Cut to length

(Part number 97739201)

DC-2 (-)

L1-7

L2-0

DC-2 (+)

L1-0

NOTES:

1. All terminals with the same name are connected together on the module. For

example, L1-0 can be connected to either terminal marked L1-0.

2. Do not physically connect more than two wires to a single RTB terminal. When

you use the third L1-7 terminal to daisy chain to other RTBs, always connect the

daisy chain to the terminal directly connected to the supply wire, as shown.

3. When using the jumper bar to daisy chain terminals together as shown, the

maximum current you may apply to the module through a single contact point

is 8A.

4. If separate power sources are used, do not exceed the specified isolation voltage.

Allen-Bradley Parts

12 ControlLogix AC (10-265V) DC (5-150V) Isolated Relay Module

Publication

1756-IN513D-EN-P - November 2003

Assemble the Removable Terminal Block and the Housing

Install the Removable Terminal Block onto the Module

Before proceeding with RTB installation, make certain:

• power is removed or the area is nonhazardous.

• field-side wiring of the RTB has been completed.

• the RTB housing is snapped in place on the RTB.

• the RTB housing is closed.

• the locking tab at the top of the module is unlocked.

WARNING

If you connect or disconnect the Removable Terminal

Block (RTB) with field side power applied, an electrical

arc can occur. This could cause an explosion in

hazardous location installations.

20858–M

Groove

Side edge of the RTB

Strain relief area

1. Align the grooves at the bottom of the housing with the side edges of the RTB.

2. Slide the RTB into the housing until it snaps into place.

20853–M 20854–M

Module

guide

RTB guides

Locking tab

1. Align the side and top, bottom guides. 2. Press quickly and evenly to seat the RTB

until the latches snap into place.

3. Slide the locking tab down.

ControlLogix AC (10-265V) DC (5-150V) Isolated Relay Module 13

Publication

1756-IN513D-EN-P - November 2003

Check the Indicators

The indicators show individual I/O status (yellow) for each point and

a bi-colored LED for module "OK" (red/green). .

During power up, an indicator test is done and the following occurs:

• "OK" indicator turns red for 1 second and then turns to

flashing green if it has passed the self-test.

• I/O status indicators turn ON for a maximum of 2 seconds and

then turn OFF.

This completes installation of the module. Use the following

information to remove the module, if necessary.

Indicator: Displaying: Means: Take this action:

OK Steady green

light

The outputs are actively being

controlled by a system

processor.

None

OK Flashing

green light

The module has passed

internal diagnostics but is not

actively controlled.

Configure the module.

OK Flashing red

light

Previously established

communication has timed out.

Check controller and chassis

communication.

OK Steady red

light

An unrecoverable error has

occurred on the module.

Replace the module.

I/O State Yellow The output is active. None

40456-M

ST 0 1 2 3 4 5 6 7

RELAY OUTPUT

Allen-Bradley Parts

14 ControlLogix AC (10-265V) DC (5-150V) Isolated Relay Module

Publication

1756-IN513D-EN-P - November 2003

Remove the Removable Terminal Block from the Module

If you need to remove the module, you must remove the RTB first.

Before removing the module, you must remove the RTB.

Remove the Module

WARNING

When you insert or remove the module while backplane

power is on, an electrical arc can occur. This could cause

an explosion in hazardous location installations. Be sure

that power is removed or the area is nonhazardous

before proceeding.

20855–M

2. Open the RTB door and pull

the RTB off the module.

1. Unlock the locking tab at

the top of the module.

42517

1. Push in top and bottom locking tabs. 2. Pull module out of the chassis.

20856–M 20857–M

ControlLogix AC (10-265V) DC (5-150V) Isolated Relay Module 15

Publication

1756-IN513D-EN-P - November 2003

1756-OX8I Specifications

Number of Outputs 8 N.O. & 8 N.C. (2 points/common)

Module Location 1756 ControlLogix Chassis

Backplane Current 100mA @ 5.1V dc & 100mA @ 24V dc

Backplane Power 2.9W

Maximum Power Dissipation

(Module)

3.1W @ 60

Thermal Dissipation 10.57 BTU/hr

Output Voltage Range 10-265V 47-63Hz/5-150V dc

Output Voltage Range

(load dependent)

5-30V dc @ 2.0A resistive

48V dc @ 0.5A resistive

125V dc @ 0.25A resistive

125V ac @ 2.0A resistive

240V ac @ 2.0A resistive

Output Current Rating

(at rated power)

Resistive

Inductive

2A @ 5-30V dc 2.0A steady state @ 5-30V dc

0.5A @ 48V dc 0.5A steady state @ 48V dc

0.25A @ 125V dc 0.25A steady state @ 125V dc

2A @ 125V ac 2.0A steady state, 15A make @

125V ac

2A @ 240V ac 2.0A steady state, 15A make @

240V ac

Power Rating (steady state) 250W maximum for 125V ac resistive output

480W maximum for 240V ac resistive output

60W maximum for 30V dc resistive output

24W maximum for 48V dc resistive output

31W maximum for 125V dc resistive output

250VA maximum for 125V ac inductive output

480VA maximum for 240V ac inductive output

60VA maximum for 30V dc inductive output

24VA maximum for 48V dc inductive output

31VA maximum for 125V dc inductive output

Allen-Bradley Parts

16 ControlLogix AC (10-265V) DC (5-150V) Isolated Relay Module

Publication

1756-IN513D-EN-P - November 2003

UL/CSA/FM ratings Output rating: C300, R150 Pilot Duty (C300=240V ac,

2.5 A thermal continuous - 7.5A make, 0.75A break

@240V ac 50/60Hz.15A make, 1.5A break@120V ac

50/60 Hz 1800VA max make, 180VA max break;

R150=1A thermal continuous - 0.22A make/break @

125V dc 28VA max make/break)

Minimum Load Current 10mA/point

Initial Contact Resistance 100m

Ω maximum @ 6V 1A

Switching Frequency 1 operation/3s (0.3Hz at rated load) maximum

Bounce Time 1.2ms (mean)

Expected Contact Life 300k cycles resistive/100k cycles inductive

Maximum Off-State Leakage

Current

0mA

Output Delay Time

OFF to ON

ON to OFF

13ms maximum

Scheduled Outputs Synchronization within 16.7 seconds maximum,

reference to the Coordinated System Time

Configurable Fault States/Point Hold Last State, ON or OFF (OFF is the default)

Config. States in Program

Mode/Point

Hold Last State, ON or OFF (OFF is the default)

Fusing Not protected - Fused IFM is recommended to protect

outputs (See publication 1492-2.12)

Isolation Voltage

Channel to channel

User to system

100% tested at 2546V dc for 1s

250V maximum continuous voltage

100% tested at 2546V dc for 1s

250V maximum continuous voltage

RTB Screw Torque (Cage clamp) 4.4 inch-pounds (0.4Nm) maximum

Module Keying (Backplane) Software configurable

RTB Keying User defined mechanical keying

Field Wiring Arm and Housing

36 Position RTB (1756-TBCH or TBS6H)

(1)

Conductors Wire Size

Allen-Bradley ControlLogix 1756-OX8I Installation Instructions Manual

Marque: Allen-Bradley

Modèle: ControlLogix 1756-OX8I

Taper: Installation Instructions Manual

Télécharger le PDF

rapport

dans d''autres langues

English: Allen-Bradley ControlLogix 1756-OX8I

Allen-Bradley ControlLogix 1756-OX8I Installation Instructions Manual

Allen-Bradley ControlLogix 1756-OX8I Installation Instructions Manual

dans d''autres langues

Documents connexes

Autres documents