Allen Bradley Allen-Bradley ControlLogix 5580 Controllers Modern Control System Manuel utilisateur

Taper
Manuel utilisateur
Installation Instructions
Original Instructions
ControlLogix 5580 Controllers
The ControlLogix® 5580 controllers help enable faster system performance, capacity, productivity, and security to help meet the growing demands of smart machines and
equipment for manufacturing.
Integrated Motion over EtherNet/IP™ for up to 256 axes.
1 Gb embedded Ethernet port enables high performance, communications, I/O, and motion control.
Secure Digital (SD) card provides optional nonvolatile memory to store user program and tag data on the controller.
Digitally signed and encrypted firmware helps protect against malicious intent.
ControlLogix NSE controllers deplete their residual stored energy to specific levels.
ControlLogix Process controllers are optimized for process applications.
ControlLogix-XT™ and ControlLogix Process controllers are designed for temperature extremes.
ControlLogix Standard controllers with a ‘K’ in the catalog number, ControlLogix NSE controllers, ControlLogix-XT controllers, and ControlLogix Process controllers
are conformal coated for extended protection in harsh, corrosive environments.
Summary of Changes
This manual contains new and updated information as indicated in the following table.
Standard Catalog Numbers: 1756-L81E, 1756-L81EK, 1756-L82E, 1756-L82EK, 1756-L83E, 1756-L83EK, 1756-L84E,
1756-L84EK, 1756-L85E, 1756-L85EK
No Stored Energy (NSE) Catalog Numbers: 1756-L81E-NSE, 1756-L82E-NSE, 1756-L83E-NSE, 1756-L84E-NSE, 1756-L85E-NSE
ControlLogix-XT Catalog Numbers: 1756-L81EXT, 1756-L82EXT, 1756-L83EXT, 1756-L84EXT, 1756-L85EXT
Process Catalog Numbers: 1756-L81EP, 1756-L83EP, 1756-L85EP
Topic Page
Product Advisories 3
Parts List 4
Required System Components 5
Product Dimensions 5
Connectors and Status Indicators 6
Install the Controller 6
Install the SD Card 7
Connect to an EtherNet/IP Network 7
Confirm Installation 7
Specifications 8
Additional Resources 8
Topic Page
Added Plug Attention Statement 6
Specifications 8
2Rockwell Automation Publication 1756-IN043D-EN-P - March 2021
ControlLogix 5580 Controllers Installation Instructions
ATTENTION: Read this document and the documents listed in the Additional Resources section about installation, configuration and operation of this equipment before you install, configure,
operate or maintain this product. Users are required to familiarize themselves with installation and wiring instructions in addition to requirements of all applicable codes, laws, and
standards.
Activities including installation, adjustments, putting into service, use, assembly, disassembly, and maintenance are required to be carried out by suitably trained personnel in accordance
with applicable code of practice. If this equipment is used in a manner not specified by the manufacturer, the protection provided by the equipment may be impaired.
岤䠑㖈㸝鄳ծꂁ縨ծ乼⡲ㄤ絶䫡劥❡ㅷ⵸霼ꢓ靀劥俒咓⟄⿺  Ⱖ➭餴彂  鿈ⴔ⴩ⴀ涸剣Ⱒ霃㢊㸝鄳ծꂁ縨ㄤ乼⡲涸湱䎾俒咓կꤑ✫䨾剣鷓欽錞薴ծ岁䖒
ㄤ叻ⲥ涸湱Ⱒ銳宠⛓㢪欽䨪鵮䗳곢擿䜪㸝鄳ㄤ䱹絁霹僈կ
㸝鄳ծ靈侮ծ䫏鵘ծ⢪欽ծ絆鄳ծ䬒⽸ㄤ絶䫡瘝ぐ고乼⡲䗳곢歋絑鵂鷓䔲雲絅涸⚁⚌➃プ䭽撑鷓欽涸乼⡲錞薴㹊倶կ
㥵卓劢䭽撑ⵖ鸣㉁䭷㹁涸倰䒭⢪欽霪霃㢊ⴭ〳腊⠔䰀㹲霃㢊䲿⣘涸⥂䫡կ
ATENCIÓN: Antes de instalar, configurar, poner en funcionamiento o realizar el mantenimiento de este producto, lea este documento y los documentos listados en la sección Recursos
adicionales acerca de la instalación, configuración y operación de este equipo. Los usuarios deben familiarizarse con las instrucciones de instalación y cableado y con los requisitos de todos
los códigos, leyes y estándares vigentes.
El personal debidamente capacitado debe realizar las actividades relacionadas a la instalación, ajustes, puesta en servicio, uso, ensamblaje, desensamblaje y mantenimiento de conformidad
con el código de práctica aplicable. Si este equipo se usa de una manera no especificada por el fabricante, la protección provista por el equipo puede resultar afectada.
ATENÇÃO: Leia este e os demais documentos sobre instalação, configuração e operação do equipamento que estão na seção Recursos adicionais antes de instalar, configurar, operar ou
manter este produto. Os usuários devem se familiarizar com as instruções de instalação e fiação além das especificações para todos os códigos, leis e normas aplicáveis.
É necessário que as atividades, incluindo instalação, ajustes, colocação em serviço, utilização, montagem, desmontagem e manutenção sejam realizadas por pessoal qualificado e
especializado, de acordo com o código de prática aplicável.
Caso este equipamento seja utilizado de maneira não estabelecida pelo fabricante, a proteção fornecida pelo equipamento pode ficar prejudicada.
ВНИМАНИЕ: Перед тем как устанавливать, настраивать, эксплуатировать или обслуживать данное оборудование, прочитайте этот документ и
документы, перечисленные в разделе «Дополнительные ресурсы». В этих документах изложены сведения об установке, настройке и эксплуатации
данного оборудования. Пользователи обязаны ознакомиться с инструкциями по установке и прокладке соединений, а также с требованиями всех
применимых норм, законов и стандартов.
Все действия, включая установку, наладку, ввод в эксплуатацию, использование, сборку, разборку и техническое обслуживание, должны выполняться
обученным персоналом в соответствии с применимыми нормами и правилами.
Если оборудование используется не предусмотренным производителем образом, защита оборудования может быть нарушена.
󴎤󲼑 : 󳦥󷢢󱡸󷫤󶔨󳸔󳃮󵫪󱕜󱁃󲔛󱑹󳦥󳥆󳦥󳼤󱬼󷫤󶔨󷫤󲕁󳕽󰽳󱛬󶙌󷽺󳛲󷭪󲰳󵶙󳄾󷪹󸋺󳛒󳥆󵕢
󸔑󷭪󲰳󳧵󰾾󴎁󲲓󷧊󳭔󷦳󰻞󱔈󷫤󶔨󸞂󶊁󳅜󹌬󶗠󴯿󲳴󷦳
󷫤󶔨󷰄󳚮󸖋󸋅󸻛󲄤󰾫󵈾󶅉󵰨󷩒󰽥󱁃󲔛󱞎󷲀󰽳󳵠󷭪󲰳󲕌󳜶󷧊󱑲󲲟󷪯󶊻󱜍󸗞󱐗󰽳󳵠󱢟󲕌󷝥󲳴󷦳
󳦥󳼤󱬼󷢢󸔢󳉸󲕁󳜰󴎁󰾫󵈾󱸦󱝖󳼤󱬼󳏀󰿙󱁃󷶋󳐧󲷋
ACHTUNG: Lesen Sie dieses Dokument und die im Abschnitt „Weitere Informationen“aufgeführten Dokumente, die Informationen zu Installation, Konfiguration und Bedienung dieses Produkts
enthalten, bevor Sie dieses Produkt installieren, konfigurieren, bedienen oder warten. Anwender müssen sich neben den Bestimmungen aller anwendbaren Vorschriften, Gesetze und Normen
zusätzlich mit den Installations- und Verdrahtungsanweisungen vertraut machen.
Arbeiten im Rahmen der Installation, Anpassung, Inbetriebnahme, Verwendung, Montage, Demontage oder Instandhaltung dürfen nur durch ausreichend geschulte Mitarbeiter und in
Übereinstimmung mit den anwendbaren Ausführungsvorschriften vorgenommen werden.
Wenn das Gerät in einer Weise verwendet wird, die vom Hersteller nicht vorgesehen ist, kann die Schutzfunktion beeinträchtigt sein.
ATTENTION : Lisez ce document et les documents listés dans la section Ressources complémentaires relatifs à l’installation, la configuration et le fonctionnement de cet équipement avant
d’installer, configurer, utiliser ou entretenir ce produit. Les utilisateurs doivent se familiariser avec les instructions d’installation et de câblage en plus des exigences relatives aux codes, lois
et normes en vigueur.
Les activités relatives à l’installation, le réglage, la mise en service, l’utilisation, l’assemblage, le démontage et l’entretien doivent être réalisées par des personnes formées selon le code de
pratique en vigueur.
Si cet équipement est utilisé d’une façon qui n’a pas été définie par le fabricant, la protection fournie par l’équipement peut être compromise.
󻷋󻰧 : 󻇇󽴔󻳫󼥗󽴔󻗳󼌧 , 󻗳󻳤 , 󻱠󺢨󽴔󺫟󺝣󽴔󻯯󻺏󽴔󻇃󻛧󼨧󺋿󽴔󻳓󻪟󽴔󻇇󽴔󻀇󻗫󺹋󽴔󼢻󼨷󼨧󻪻󽴔󻗳󼌧, 󻗳󻳤󽴔󻃞󽴔󻱠󺢨󻪟󽴔󺇏󼨫󽴔󼄇󺆯󽴔󻱟󺶛󽴔󻘈󻘧󻰧󽴔󻀇󻗫󺦳󻰓󽴔󻃧󺦫󻞫󽴔󻱌󺆯󽴔󻛨󻺏󼨧󻞼󻞫󻫳 . 󻕻󻭸󻱟󺝣󽴔󺽷󺦯󽴔
󺇏󺳷󽴔󺊫󻳤 , 󻅤󺊫󽴔󻃞󽴔󼤫󻷏󻪟󻗫󽴔󻭣󺈻󼨧󺝣󽴔󻕻󼨼󻪟󽴔󺟏󼩃󽴔󻃧󺦫󻞫󽴔󻗳󼌧󽴔󻃞󽴔󻃿󻗯󽴔󻺏󼌷󻰓󽴔󻛨󻺏󼩃󻩋󽴔󼨸󺞗󺞳 .
󻗳󼌧 , 󻴿󻳤 , 󺃏󺢨 , 󻕻󻭸 , 󻴿󺺌 , 󻉓󼩃 , 󻯯󻺏󻇃󻛧󽴔󺧀󽴔󺽷󺦯󽴔󻱠󻪔󻰏󽴔󺇏󺳷󽴔󺊫󻳤󻪟󽴔󺧿󺱋󽴔󻳐󻳗󼨫󽴔󺈟󻯰󻰓󽴔󻃪󻰏󽴔󻕻󻭸󻱟󺹋󽴔󼚄󼩃󻗫󺺛󽴔󻛧󼩘󼩃󻩋󽴔󼨸󺞗󺞳 .
󻇇󽴔󻱴󻌓󺹋󽴔󻳫󻴿󻕻󺃏󽴔󺽔󻞫󼨧󻺏󽴔󻨙󻰏󽴔󻃸󻅤󻰋󺴫󽴔󻕻󻭸󼨧󺽃󽴔󻱴󻌓󻰧󽴔󻇃󼬇󽴔󺋿󺝴󻱃󽴔󻙟󻖐󺣯󽴔󻛧󽴔󻱗󻞄󺞗󺞳 .
ATTENZIONE Prima di installare, configurare ed utilizzare il prodotto, o effettuare interventi di manutenzione su di esso, leggere il presente documento ed i documenti elencati nella sezione
“Altre risorse”, riguardanti l’installazione, la configurazione ed il funzionamento dell’apparecchiatura. Gli utenti devono leggere e comprendere le istruzioni di installazione e cablaggio, oltre ai
requisiti previsti dalle leggi, codici e standard applicabili.
Le attività come installazione, regolazioni, utilizzo, assemblaggio, disassemblaggio e manutenzione devono essere svolte da personale adeguatamente addestrato, nel rispetto delle
procedure previste.
Qualora l’apparecchio venga utilizzato con modalità diverse da quanto previsto dal produttore, la sua funzione di protezione potrebbe venire compromessa.
DİKKAT: Bu ürünün kurulumu, yapılandırılması, işletilmesi veya bakımı öncesinde bu dokümanı ve bu ekipmanın kurulumu, yapılandırılması ve işletimi ile ilgili İlave Kaynaklar bölümünde yer
listelenmiş dokümanları okuyun. Kullanıcılar yürürlükteki tüm yönetmelikler, yasalar ve standartların gereksinimlerine ek olarak kurulum ve kablolama talimatlarını da öğrenmek zorundadır.
Kurulum, ayarlama, hizmete alma, kullanma, parçaları birleştirme, parçalarıkme ve bakım gibi aktiviteler sadece uygun eğitimleri almış kişiler tarafından yürürlükteki uygulama
yönetmeliklerine uygun şekilde yapılabilir.
Bu ekipman üretici tarafından belirlenmiş amacın dışında kullanılırsa, ekipman tarafından sağlanan koruma bozulabilir.
岤䠑✲갪㖈㸞酤鏤㹁乽⡲䧴笞隌劥欴ㅷ⵹锞⯓ꠗ隡姽俒⟝⟃⿻⴪倴 չⰦ➮须彂պ畎眏⚥剤ꡠ㸞酤鏤㹁莅乽⡲姽鏤⪔涸俒⟝⢪欽罏䗳갭擿䜫㸞
ㄤꂂ箁䭸爚⚛痘ざ䨾剤岁鋊岁䖒ㄤ垦彋銴宠
⺫䭍㸞酤锅侮❜➰⢪欽⢪欽穉酤䬓⽹ㄤ笞隌瘞⹛⡲鿪䗳갭❜歋䊺竤麕黠殹鎯箻涸➃㆞鹎遤⟃痘ざ黠欽涸㻜⡲岁鋊
㥶卓㼟鏤⪔欽倴ꬌ醢鸤㉂䭸㹁涸欽鸁儘〳腋剚鸤䧭鏤⪔䨾䲿⣘涸⥃隌⸆腋「䴦
POZOR: Než začnete instalovat, konfigurovat či provozovat tento výrobek nebo provádět jeho údržbu, přečtěte si tento dokument a dokumenty uvedené v části Dodatečné zdroje ohledně
instalace, konfigurace a provozu tohoto zařízení. Uživatelé se musejí vedle požadavků všech relevantních vyhlášek, zákonů anorem nutně seznámit také s pokyny pro instalaci a elektrické
zapojení.
Činnosti zahrnující instalaci, nastavení, uvedení do provozu, užívání, montáž, demontáž a údržbu musí vykonávat vhodně proškolený personál v souladu s příslušnými prováděcími předpisy.
Pokud se toto zařízení používá způsobem neodpovídajícím specifikaci výrobce, může být narušena ochrana, kterou toto zařízení poskytuje.
UWAGA: Przed instalacją, konfiguracją, użytkowaniem lub konserwacją tego produktu należy przeczytać niniejszy dokument oraz wszystkie dokumenty wymienione w sekcji Dodatkowe
źródła omawiające instalację, konfigurację i procedury użytkowania tego urządzenia. Użytkownicy mają obowiązek zapoznać się z instrukcjami dotyczącymi instalacji oraz oprzewodowania,
jak również z obowiązującymi kodeksami, prawem i normami.
Działania obejmujące instalację, regulację, przekazanie do użytkowania, użytkowanie, montaż, demontaż oraz konserwację muszą być wykonywane przez odpowiednio przeszkolony personel
zgodnie z obowiązującym kodeksem postępowania.
Jeśli urządzenie jest użytkowane w sposób inny niż określony przez producenta, zabezpieczenie zapewniane przez urządzenie może zostać ograniczone.
OBS! Läs detta dokument samt dokumentet, som står listat i avsnittet Övriga resurser, om installation, konfigurering och drift av denna utrustning innan du installerar, konfigurerar eller
börjar använda eller utföra underhållsarbete på produkten. Användare måste bekanta sig med instruktioner för installation och kabeldragning, förutom krav enligt gällande koder, lagar och
standarder.
Åtgärder som installation, justering, service, användning, montering, demontering och underhållsarbete måste utföras av personal med lämplig utbildning enligt lämpligt bruk.
Om denna utrustning används på ett sätt som inte anges av tillverkaren kan det hända att utrustningens skyddsanordningar försätts ur funktion.
LET OP: Lees dit document en de documenten die genoemd worden in de paragraaf Aanvullende informatie over de installatie, configuratie en bediening van deze apparatuur voordat u dit
product installeert, configureert, bediend of onderhoudt. Gebruikers moeten zich vertrouwd maken met de installatie en de bedradingsinstructies, naast de vereisten van alle toepasselijke
regels, wetten en normen.
Activiteiten zoals het installeren, afstellen, in gebruik stellen, gebruiken, monteren, demonteren en het uitvoeren van onderhoud mogen uitsluitend worden uitgevoerd door hiervoor opgeleid
personeel en in overeenstemming met de geldende praktijkregels.
Indien de apparatuur wordt gebruikt op een wijze die niet is gespecificeerd door de fabrikant, dan bestaat het gevaar dat de beveiliging van de apparatuur niet goed werkt.
Rockwell Automation Publication 1756-IN043D-EN-P - March 2021 3
ControlLogix 5580 Controllers Installation Instructions
Product Advisories
ATTENTION:
In case of malfunction or damage, no attempts at repair should be made. The module should be returned to the manufacturer for repair. Do not
dismantle the module.
The USB port is intended for temporary local programming purposes only and not intended for permanent connection. The USB cable is not to exceed
3.0 m (9.84 ft) and must not contain hubs.
Use only a soft dry anti-static cloth to wipe down equipment. Do not use any cleaning agents.
When ControlLogix 5580 Standard and ControlLogix 5580 NSE controllers are installed in a 1756 Series B Chassis, this equipment is certified for use
only within the surrounding air temperature range of 0…50 °C (32…122 °F). The equipment must not be used outside of this range.
When ControlLogix 5580 Standard and ControlLogix 5580 NSE controllers are installed in a 1756 Series C Chassis, this equipment is certified for use
only within the surrounding air temperature range of 0…60 °C (32…140 °F). The equipment must not be used outside of this range.
When ControlLogix-XT 5580 Controllers and ControlLogix 5580 Process controllers are installed in a 1756 Series B Chassis, this equipment is certified
for use only within the surrounding air temperature range of -25…+50 °C (-13…+122 °F). The equipment must not be used outside of this range.
When ControlLogix-XT 5580 Controllers and ControlLogix 5580 Process controllers are installed in a 1756 Series C Chassis, this equipment is certified
for use only within the surrounding air temperature range of -25…+60 °C (-13…+140 °F). The equipment must not be used outside of this range.
•When ControlLogix-XT 5580 Controllers and ControlLogix 5580 Process controllers are installed in a ControlLogix-XT Series C Chassis, this equipment
is certified for use only within the surrounding air temperature range of -25…+70 °C (-13…+158 °F). The equipment must not be used outside of this
range.
WARNING:
When you press the reset button while power is on, an electric arc can occur. This could cause an explosion in hazardous location installations.
Be sure that power is removed or the area is nonhazardous before proceeding.
Do not use the USB port in hazardous locations.
North American Hazardous Location Approval
The following information applies when operating this equipment in
hazardous locations. Informations sur l’utilisation de cet équipement en environnements dangereux.
Products marked "CL I, DIV 2, GP A, B, C, D" are suitable for use in Class I Division 2
Groups A, B, C, D, Hazardous Locations and nonhazardous locations only. Each
product is supplied with markings on the rating nameplate indicating the
hazardous location temperature code. When combining products within a
system, the most adverse temperature code (lowest "T" number) may be used to
help determine the overall temperature code of the system. Combinations of
equipment in your system are subject to investigation by the local Authority
Having Jurisdiction at the time of installation.
Les produits marqués "CL I, DIV 2, GP A, B, C, D" ne conviennent qu'à une utilisation en
environnements de Classe I Division 2 Groupes A, B, C, D dangereux et non dangereux.
Chaque produit est livré avec des marquages sur sa plaque d'identification qui
indiquent le code de température pour les environnements dangereux. Lorsque
plusieurs produits sont combinés dans un système, le code de température le plus
défavorable (code de température le plus faible) peut être utilisé pour déterminer le
code de température global du système. Les combinaisons d'équipements dans le
système sont sujettes à inspection par les autorités locales qualifiées au moment de
l'installation.
WARNING:
Explosion Hazard –
Do not disconnect equipment unless power has been
removed or the area is known to be nonhazardous.
Do not disconnect connections to this equipment unless
power has been removed or the area is known to be
nonhazardous. Secure any external connections that mate to
this equipment by using screws, sliding latches, threaded
connectors, or other means provided with this product.
Substitution of components may impair suitability for Class I,
Division 2.
If this product contains batteries, they must only be changed
in an area known to be nonhazardous.
AVERTISSEMENT:
Risque d’Explosion –
Couper le courant ou s'assurer que l'environnement est clas
non dangereux avant de débrancher l'équipement.
Couper le courant ou s'assurer que l'environnement est clas
non dangereux avant de débrancher les connecteurs. Fixer tous
les connecteurs externes reliés à cet équipement à l'aide de vis,
loquets coulissants, connecteurs filetés ou autres moyens
fournis avec ce produit.
La substitution de composants peut rendre cet équipement
inadapté à une utilisation en environnement de Classe I,
Division 2.
S'assurer que l'environnement est classé non dangereux avant de
changer les piles.
European Hazardous Location Approval
The following applies to products marked , II 3 G:
Are Equipment Group II, Equipment Category 3, and comply with the Essential Health and Safety Requirements relating to the design and construction of such
equipment given in Annex II to Directive 94/9/EC. See the EC Declaration of Conformity at rok.auto/certifications for details.
The type of protection is for Ex nA IIC T4 Gc according to EN 60079-15.
Comply to standards: EN 60079-0:2012+A11:2013, EN60079-15:2010, reference certificate number DEMKO13ATEX1325026X.
Are intended for use in areas in which explosive atmospheres caused by gases, vapors, mists, or air are unlikely to occur, or are likely to occur only infrequently and
for short periods. Such locations correspond to Zone 2 classification according to ATEX directive 1999/92/EC.
Can have catalog numbers followed by a "K" to indicate a conformal coating option.
4Rockwell Automation Publication 1756-IN043D-EN-P - March 2021
ControlLogix 5580 Controllers Installation Instructions
Parts List
The controller ships with these parts:
A key for the mode switch
2 GB Secure Digital Card (1784-SD2), pre-installed in the controller
IEC Hazardous Location Approval
The following applies to products with IECEx certification:
Are intended for use in areas in which explosive atmospheres caused by gases, vapors, mists, or air are unlikely to occur, or are likely to occur only infrequently and
for short periods. Such locations correspond to Zone 2 classification to IEC 60079-0.
The type of protection is Ex nA IIC T4 Gc according to IEC 60079-15.
Such modules comply to Standards IEC 60079-0:6th Edition, IEC 60079-15:4th Edition, reference IECEx certificate number IECExUL14.0008X.
Can have catalog numbers followed by a "K" to indicate a conformal coating option.
Special Conditions for Safe Use
WARNING:
This equipment is not resistant to sunlight or other sources of UV radiation.
This equipment shall be mounted in an ATEX/IECEx Zone 2 certified enclosure with a minimum ingress protection rating of at least IP54
(as defined in EN/IEC 60529) and used in an environment of not more than Pollution Degree 2 (as defined in EN/IEC 60664-1) when
applied in Zone 2 environments.
The enclosure must be accessible only by the use of a tool.
This equipment shall be used within its specified ratings defined by Rockwell Automation.
Provision shall be made to prevent the rated voltage from being exceeded by transient disturbances of more than 140% of the rated
voltage when applied in Zone 2 environments.
The instructions in the user manual shall be observed.
This equipment must be used only with ATEX/IECEx certified Rockwell Automation backplanes.
Do not disconnect equipment unless power has been removed or the area is known to be nonhazardous.
The USB port is intended for temporary local programming purposes only and not intended for permanent connection. Do not use the
USB port in hazardous locations.
Environment and Enclosure
ATTENTION: This equipment is intended for use in a Pollution Degree 2 industrial environment, in overvoltage Category II applications (as
defined in EN 60664-1), at altitudes up to 2000 m (6562 ft) without derating.
This equipment is not intended for use in residential environments and may not provide adequate protection to radio communication
services in such environments.
This equipment is supplied as open-type equipment for indoor use. It must be mounted within an enclosure that is suitably designed for
those specific environmental conditions that will be present and appropriately designed to prevent personal injury resulting from
accessibility to live parts. The enclosure must have suitable flame-retardant properties to prevent or minimize the spread of flame,
complying with a flame spread rating of 5VA or be approved for the application if non-metallic. The interior of the enclosure must be
accessible only by the use of a tool. Subsequent sections of this publication may contain more information regarding specific enclosure
type ratings that are required to comply with certain product safety certifications.
In addition to this publication, see the following:
Industrial Automation Wiring and Grounding Guidelines, publication 1770-4.1, for more installation requirements.
NEMA Standard 250 and EN/IEC 60529, as applicable, for explanations of the degrees of protection provided by different types of
enclosure.
IMPORTANT Any illustrations, charts, sample programs, and layout examples that are shown in this publication are intended solely for the purposes of
example. Since there are many variables and requirements that are associated with any particular installation, Rockwell Automation does not
assume responsibility or liability for actual use based on the examples that are shown in this publication.
Rockwell Automation Publication 1756-IN043D-EN-P - March 2021 5
ControlLogix 5580 Controllers Installation Instructions
Required System Components
To use the controller, a chassis and power supply are required. For controller and chassis operating specifications, see the 1756 ControlLogix Controller Specifications
Technical Data, publication 1756-TD001.
Product Dimensions
Component Catalog Number
ControlLogix Standard Chassis, series C and series B 1756-A4, 1756-A4K, 1756-A7, 1756-A7K, 1756-A10, 1756-A10K, 1756-A13, 1756-A13K, 1756-A17, 1756-A17K
Power supply, standard 1756-PA72, 1756-PA72K, 1756-PA75, 1756-PA75K, 1756-PB72, 1756-PB72K,1756-PB75, 1756-PB75K,1756-PC75,
1756-PH75
Power supply, standard slim 1756-PA50, 1756-PA50K, 1756-PB50, 1756-PB50K
Power supply, redundant 1756-PA75R, 1756-PA75RK,1756-PB75R, 1756-PB75RK, 1756-PSCA2, 1756-PSCA2K
ControlLogix-XT Chassis, series C 1756-A7XT, 1756-A10XT
ControlLogix-XT Power supply 1756-PAXT, 1756-PBXT
ControlLogix-XT Slim Power supply 1756-PA30XT, 1756-PB30XT
ControlLogix-XT Redundant Power supply 1756-PAXTR, 1756-PBXTR
139.6 mm
(5.50 in.)
34.55 mm
(1.360 in.)
145.2 mm
(5.717 in.)
6Rockwell Automation Publication 1756-IN043D-EN-P - March 2021
ControlLogix 5580 Controllers Installation Instructions
Connectors and Status Indicators
Install the Controller
Added Plug Attention Statement
Before you install the controller, make sure to follow the instructions in the
ControlLogix Chassis and Power Supply Installation Instructions,
publication 1756-IN005.
When installing a ControlLogix controller, you can do the following:
Place the controller in any slot.
Use multiple controllers in the same chassis.
You can install or remove a ControlLogix controller while chassis power is on and
the system is operating.
1. Align the circuit board with the top and bottom guides in the chassis.
2. Slide the module into the chassis until it snaps into place.
3. Verify that the controller is flush with the power supply or other
installed modules.
ATTENTION: If you are using a ControlLogix 5580 Standard
or NSE controller to the maximum temperature of 60 °C
(140 °F), you must use a ControlLogix chassis, series C.
If you are using a ControlLogix-XT 5580 or ControlLogix
Process controller to the maximum temperature of 70 °C
(158 °F), you must use a ControlLogix-XT chassis, series C.
WARNING: When you insert or remove the module while
backplane power is on, an electric arc can occur. This could
cause an explosion in hazardous location installations. Be sure
that power is removed or the area is nonhazardous before
proceeding. Repeated electrical arcing causes excessive wear
to contacts on both the module and its mating connector. Worn
contacts can create electrical resistance that can affect
module operation.
ATTENTION: The ControlLogix 5580 controllers that are
listed on page 1 of this document that end with a ‘K’ or ‘XT’
are shipped with port protection plugs installed to provide a
layer of protection from corrosive atmospheres. Port plugs
must remain installed in unused ports at all times during
storage and operation for the product to meet its corrosive
atmosphere rating. If temporary access is required, plugs
can be removed, and should be reinserted after temporary
access is complete.
1
4
3
5
6
2
Item Description
1 4-character display
2 Status Indicators
3 Mode switch (Remote, Run, Program)
4 Ethernet Port
5 Ethernet Status Indicators
6 SD card slot and Reset Button are behind the door.
7 USB Port
7
ATTENTION: This equipment is sensitive to electrostatic
discharge, which can cause internal damage and affect
normal operation.
Follow these guidelines when you handle this equipment:
Touch a grounded object to discharge potential static.
Wear an approved grounding wriststrap.
Do not touch connectors or pins on component boards.
Do not touch circuit components inside the equipment.
Use a static-safe workstation, if available.
Store the equipment in appropriate static-safe packaging
when not in use.
Top Circuit
Board Aligned
Bottom Circuit
Board Aligned
Rockwell Automation Publication 1756-IN043D-EN-P - March 2021 7
ControlLogix 5580 Controllers Installation Instructions
Install the SD Card
If the SD card is not already installed in the controller, then complete these steps to
install the SD card.
1. Verify that the SD card is locked or unlocked according to your preference.
For more information about the lock/unlock memory settings,
see the ControlLogix 5580 Controllers User Manual, publication 1756-UM543.
2. Remove the key.
3. To access the SD card slot, open the door on the controller key panel.
4. Position the SD card so that the contact end goes into the controller,
with the contacts on the right and the label on the left. The beveled corner
is on top.
5. Insert the SD card into the card slot and gently press the card until it clicks
into place.
6. The card slides in easily, if it is oriented correctly. You can insert the card
only one way.
7. Close the door.
8. Reinsert the key, if desired.
Connect to an EtherNet/IP Network
If you are connecting the controller directly to an EtherNet/IP network, then
connect an RJ45 cable to the Ethernet port on the controller.
Confirm Installation
After you have inserted the controller into the chassis and applied power,
the 4-character display and status indicators display status information for the
controller. See the ControlLogix 5580 and GuardLogix® 5580 Controllers User
Manual, publication 1756-UM543, for information on how to interpret the
4-character display messages and the status indicators.
WARNING: When you insert or remove the SD memory card
while power is on, an electric arc can occur. This could cause an
explosion in hazardous location installations. Be sure that power
is removed or the area is nonhazardous before proceeding.
Unlocked Locked
32005-M
SD Card
SD Card
WAR NIN G: If you connect or disconnect the communications
cable with power applied to this module or any device on the
network, an electric arc can occur. This could cause an
explosion in hazardous location installations. Be sure that power
is removed or the area is nonhazardous before proceeding.
ATTENTION: 10 Mbps Ethernet automatic negotiations are
functional. However, 10 Mbps Ethernet connections are not
fully supported or intended for normal use. Use 10 Mbps
Ethernet connections only if necessary during temporary
setup.
8Rockwell Automation Publication 1756-IN043D-EN-P - March 2021
ControlLogix 5580 Controllers Installation Instructions
Specifications
Additional Resources
These documents contain additional information concerning related products from Rockwell Automation.
You can view or download publications at rok.auto/literature.
Attribute
1756-L81E, 1756-L81EK,
1756-L82E, 1756-L82EK,
1756-L83E, 1756-L83EK,
1756-L84E, 1756-L84EK,
1756-L85E, 1756-L85EK
1756-L81E-NSE,
1756-L82E-NSE,
1756-L83E-NSE,
1756-L84E-NSE,
1756-L85E-NSE
1756-L81EXT,
1756-L82EXT,
1756-L83EXT,
1756-L84EXT,
1756-L85EXT
1756-L81EP,
1756-L83EP,
1756-L85EP
Temperature, operating
IEC 60068-2-1 (Test Ad, Operating Cold),
IEC 60068-2-2 (Test Bd, Operating
Dry Heat),
IEC 60068-2-14 (Test Nb, Operating
Thermal Shock)
0 °C < Ta < +60 °C (+32 °F < Ta < +140 °F) for Standard Chassis,
Series C
0 °C < Ta < +50 °C (+32 °F < Ta < +122 °F) for Standard Chassis,
Series B
-25 °C < Ta < +70 °C (-13°F < Ta < +158 °F) for XT Chassis,
Series C
-25 °C < Ta < +60 °C (-13 °F < Ta < +140 °F) for Standard
Chassis, Series C
-25 °C < Ta < +50 °C (-13 °F < Ta < +122 °F) for Standard
Chassis, Series B
Temperature, Surrounding Air max 60 °C (140 °F) for Standard Chassis, Series C
50 °C (122 °F) for Standard Chassis, Series B
70 °C (158 °F) for XT Chassis, Series C
60 °C (140 °F) for Standard Chassis, Series C
50 °C (122 °F) for Standard Chassis, Series B
Corrosive Atmosphere(1)
ASTM B845-97 Method H Accelerated
Test (20-Day Exposure)
(1) Only applicable to modules that end with a ‘K’ or ‘XT’.
Severity Level G3(2) per ANSI/ISA 71.04–2013, Airborne Contaminants—Gases
Severity Level CX(2)(3) per IEC 60721-3-3:2019, Chemically Active Substances
(2) Port Plugs must remain installed in unused ports at all times during storage and operation for the product to meet it’s corrosive atmosphere rating.
(3) Up to 9.6 microns per year, corrosion rate of copper.
Enclosure type rating None (open-style)
Voltage and current ratings 1200 mA @ 5.1V DC
5.0 mA @ 1.2V DC
Isolation Voltage 50V (continuous), Basic Insulation type, USB port to Backplane, Ethernet port to Backplane, and USB Port to Ethernet port.
Type tested at 1000V AC for 60 seconds
Weight, approx 394 g (0.868 lb)
Wire size Ethernet cabling and installation according to IEC 61918 and IEC 61784-5-2
North American temp code T4
ATEX Temp Code T4
IECEx Temp Code T4
Resource Description
1756 ControlLogix Controller Specifications Technical Data, publication 1756-TD001 Provides controller specifications, including communication options,
memory use, compatibilities, redundancy, and available accessories.
1756 ControlLogix Power Supplies Specifications Technical Data, publication 1756-TD005 Provides technical specifications for ControlLogix power supplies.
1756 ControlLogix Chassis Specifications Technical Data, publication 1756-TD006 Provides chassis specifications, including spacing requirements,
mounting dimensions, and available accessories.
ControlLogix Chassis Installation Instructions, publication 1756-IN621 Provides information on how to install ControlLogix chassis.
ControlLogix Power Supply Installation Instructions, publication 1756-IN619 Provides information on how to install ControlLogix standard power
supplies.
ControlLogix Redundant Power Supply Installation Instructions, publication 1756-IN620 Provides information on how to install ControlLogix redundant power
supplies.
ControlLogix 5580 and GuardLogix® 5580 Controllers User Manual, publication 1756-UM543 Provides information on how to configure, select I/O modules, manage
communication, develop applications, and troubleshoot the ControlLogix
5580 controllers.
Replacement Guidelines: Logix 5000™ Controllers Reference Manual, publication 1756-RM100 Compares ControlLogix 5580 controllers to ControlLogix 5560/5570
controllers, and provides guidelines on the features, functions,
instruction updates, and differences between controllers.
Industrial Automation Wiring and Grounding Guidelines, publication 1770-4.1 Provides general guidelines for installing a Rockwell Automation
industrial system.
Product Certifications website, rok.auto/certifications Provides declarations of conformity, certificates, and other certification
details.
Rockwell Automation Publication 1756-IN043D-EN-P - March 2021 9
ControlLogix 5580 Controllers Installation Instructions
Notes:
10 Rockwell Automation Publication 1756-IN043D-EN-P - March 2021
ControlLogix 5580 Controllers Installation Instructions
Notes:
Rockwell Automation Publication 1756-IN043D-EN-P - March 2021 11
ControlLogix 5580 Controllers Installation Instructions
Notes:
Publication 1756-IN043D-EN-P - March 2021 | Supersedes Publication 1756-IN043C-EN-P-July 2020
Copyright © 2021 Rockwell Automation, Inc. All rights reserved. Printed in the U.S.A.
Rockwell Otomasyon Ticaret A.Ş. Kar Plaza İş Merkezi E Blok Kat:6 34752 İçerenköy, İstanbul, Tel: +90 (216) 5698400 EEE Yönetmeliğine Uygundur
PN-625857
Allen-Bradley, ControlLogix, ControlLogix-XT, expanding human possibility, FactoryTalk, GuardLogix, Logix 5000, and Rockwell Automation are trademarks of
Rockwell Automation, Inc.
EtherNet/IP is a trademark of ODVA, Inc.
Trademarks not belonging to Rockwell Automation are property of their respective companies.
Your comments help us serve your documentation needs better. If you have any suggestions on how to improve our content, complete the form at rok.auto/docfeedback.
For technical support, visit rok.auto/support.
Waste Electrical and Electronic Equipment (WEEE)
Rockwell Automation maintains current product environmental compliance information on its website at rok.auto/pec.
At the end of life, this equipment should be collected separately from any unsorted municipal waste.
Rockwell Automation Support
Use these resources to access support information.
Documentation Feedback
Your comments help us serve your documentation needs better. If you have any suggestions on how to improve our content, complete the form at rok.auto/docfeedback.
Technical Support Center Find help with how-to videos, FAQs, chat, user forums, and product notification updates. rok.auto/support
Knowledgebase Access Knowledgebase articles. rok.auto/knowledgebase
Local Technical Support Phone Numbers Locate the telephone number for your country. rok.auto/phonesupport
Literature Library Find installation instructions, manuals, brochures, and technical data publications. rok.auto/literature
Product Compatibility and Download Center
(PCDC) Download firmware, associated files (such as AOP, EDS, and DTM), and access product
release notes. rok.auto/pcdc
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12

Allen Bradley Allen-Bradley ControlLogix 5580 Controllers Modern Control System Manuel utilisateur

Taper
Manuel utilisateur