Use and Care & Installation Guide
Refrigerator
GE Appliances
Top-Mount No-Frost Models—
Export G-Line: 18–25
English Version ................................. 2
Version française ......................... 23
Versión en español .................... 45
Safety Instructions ....................... 3
Operating Instructions, Tips
Accessories .................................................... 5
Anti-Moisture Switch ................................... 2
Automatic Icemaker .................................... 8
Freezer Compartment ................................. 7
Icemaker Accessory Kit ............................... 8
Shelves ....................................................... 4, 5
Storage Drawers ...................................... 6, 7
Temperature Controls ................................. 3
Care and Cleaning
Behind Refrigerator ...................................... 9
Cleaning—Inside and Outside .................... 9
Drawer and Cover Removal ................ 9, 10
Light Bulb Replacement ........................... 10
Under Refrigerator ....................................... 9
Problem Solver ..................... 20, 21
Normal Operating Sounds ....................... 20
Preparation
Clearances ................................................... 11
Dimensions .................................................. 11
Rollers ........................................................... 11
Vacation and Moving ................................ 11
Water Supply to Icemaker ....................... 11
Installation ................................ 12–19
Earthing ................................................. 12, 13
Electrical Requirements .................... 12, 13
Fitting a Different Plug .............................. 13
Great Britain and Ireland .......................... 13
Mains Lead Replacement ................... 2, 13
Reversing the Door Swing ............... 16–19
Water Line Installation ...................... 14, 15
Model and Serial Numbers ........................ 2
HELP US HELP YOU…
Read this guide carefully. Write down the model and serial numbers.
It is intended to help you operate and maintain your new refrigerator
properly. Keep it handy for answers to your questions.
If you received a damaged refrigerator…
Immediately contact the dealer (or builder) that sold you
the refrigerator.
Save time and money. Before you request service…
Check the Problem Solver. It lists minor operating problems that you
can correct yourself.
You’ll see them on a label on the left side, near the top of the fresh
food compartment.
Model Number
Serial Number
Use these model and serial numbers in any correspondence or service
calls concerning your refrigerator.
WARNING—When using this appliance, always
exercise basic safety precautions, including the
following:
• Use this appliance only for its intended purpose as described
in this Use and Care Guide.
• This refrigerator must be properly installed in accordance
with the Installation Instructions before it is used. See
grounding instructions in the Installation section.
WARNING: Connect to potable water supply
only.
• Never unplug your refrigerator by pulling on the power
cord. Always grip plug firmly and pull straight out from
the outlet.
• Repair or replace immediately all electric service cords
that have become frayed or otherwise damaged. Do not use
a cord that shows cracks or abrasion damage along its length
or at either the plug or appliance end.
• When moving your refrigerator away from the wall, be
careful not to roll over or damage the power cord.
• Do not allow children to climb, stand or hang on the shelves
in the refrigerator. They could damage the refrigerator and
seriously injure themselves.
• If your old refrigerator is still around the house
but not in use, be sure to remove the doors. This
will reduce the possibility of danger to children.
• After your refrigerator is in operation, do not touch the
cold surfaces in the frozen food storage compartment,
particularly when hands are damp or wet. Skin may adhere
to these extremely cold surfaces.
• If your refrigerator has an automatic icemaker, avoid
contact with the moving parts of the ejector mechanism, or
with the heating element that releases the cubes. Do not
place fingers or hands on the automatic icemaking mechanism
while the refrigerator is plugged in.
• Don’t refreeze frozen foods which have thawed completely.
Food safety experts say:
‘‘…You may safely refreeze frozen foods that have thawed if
they still contain ice crystals or if they are still cold—below 4°C.
‘‘…Thawed ground meats, poultry or fish that have any off-odor
or off-color should not be refrozen and should not be eaten.
Thawed ice cream should be discarded. If the odor or color of
any food is poor or questionable, get rid of it. The food may be
dangerous to eat.
‘‘…Even partial thawing and refreezing reduces the eating
quality of foods, particularly fruits, vegetables and prepared
foods. The eating quality of red meats is affected less than that of
many other foods. Use refrozen foods as soon as possible to save
as much of their eating quality as you can.’’
• Unplug your refrigerator before cleaning and making
repairs. NOTE: We strongly recommend that any servicing
be performed by a qualified individual.
• Before replacing a burned-out light bulb, the refrigerator
should be unplugged in order to avoid contact with a live wire
filament. (A burned-out light bulb may break when being
replaced.) NOTE: Turning control to “0” position does not
remove power to the light circuit.
• Do not store or use gasoline or other flammable vapors and
liquids in the vicinity of this or any other appliance.
Mains lead replacement
If the mains lead on your refrigerator needs replacing at any time,
it must be replaced by a special lead which is obtainable from
your local dealer. A charge will be made for the replacement of
the mains lead if you have damaged the lead.
SAVE THESE
INSTRUCTIONS
IMPORTANT SAFETY INSTRUCTIONS
Read all instructions before using this appliance.
2
TEMPERATURE CONTROLS
Important Safety Instructions Temperature Controls
How to Test Temperatures No Defrosting
Use the milk test for the fresh food compartment. Place a
container of milk on the top shelf in the fresh food compartment.
Check it a day later. If the milk is too warm or too cold, adjust the
temperature controls.
Use the ice cream test for the frozen food storage compartment.
Place a container of ice cream in the center of the frozen food storage
compartment. Check it after a day. If it’s too hard or too soft, adjust
the temperature controls.
After changing the controls, always allow 24 hours for the
refrigerator to reach the temperature you have set.
It is not necessary to defrost the frozen food storage compartment
or fresh food compartment. Although your refrigerator is designed
and equipped to defrost itself automatically, some frost on packages
is normal.
3
Fresh Food Frozen Food
Initially set both controls at “4.”
The fresh food control moves
a damper to change the amount
of cold air that moves from the
frozen food compartment to the
fresh food compartment.
The frozen food control
maintains the temperatures
throughout the frozen food
storage compartment. Moving
the frozen food control to “0”
stops cooling in both areas—
fresh food and frozen food
storage compartments—but
does not shut off power to
the refrigerator.
Effervescent drinks should not be stored in the frozen food storage
compartment. For fastest food freezing, set the frozen food control at
position “7.” Since the compressor will run 100% of the time at this
setting, don’t forget to turn back the setting after the food is frozen.
0
7
5
3
1
6
4
2
7
1
4
Cold air
from frozen
food storage
compartment
Side View
Damper
(coldest setting)
(warmest setting)
Damper
Ambient Room Temperature Limits Anti-Moisture Switch
This refrigerator is designed to operate in ambient temperatures
specified by its Temperature Class which is marked on the rating plate.
Temperature Symbol Ambient Temperature
Class
Maximum Minimum
Extended-
Temperate SN 32°C 10°C
Temperate N 32°C 16°C
Subtropical ST 38°C 18°C
Tropical T 43°C 18°C
NOTE: Internal temperature may be affected by such factors as the
location of the refrigerator, ambient temperature and frequency of
door openings. Adjust temperature controls as required to compensate
for these factors.
The anti-moisture switch is located on the
temperature control panel. To reduce the amount
of electricity required to operate your refrigerator,
push switch to the left.
This turns off the unit in your refrigerator that
prevents moisture from forming on the inside or
outside surfaces.
With this unit turned off, moisture may form on the
inside or outside of your refrigerator, especially when the weather is
humid. The humidity is most likely to be high in the summer, in the
early morning hours, and in homes which are not air conditioned.
Over an extended period of time, moisture that forms on the
refrigerator surface may cause deterioration of the paint finish. It will
be important to protect the finish by using appliance polish wax as
described in the Care and Cleaning section.
The cost to operate the low-wattage unit is about the same as it costs
to use two night lights.
When you move the anti-moisture switch to the right, low wattage
electricity flows through the unit and warms the outside of the
refrigerator and the top of the fresh food section. Under most
conditions, this prevents the forming of moisture or water droplets.
Removable Wine Rack (on some models)
The wine rack is designed to hold
a bottle on its side and will fit on
any shelf.
Extra Frozen Food Storage Compartment Shelf
(on some models)
Some models have an extra
frozen food storage
compartment shelf that allows
you to use the frozen food
storage compartment space
more efficiently.
SHELVES
Adjustable Shelves (on some models)
Shelves in the fresh food and
frozen food storage
compartments are adjustable,
enabling you to make
efficient shelf arrangements
to fit your family’s food
storage needs. Steel shelves
in the frozen food storage
compartment in some
models are adjustable in the
same way.
To remove shelves: Tilt the
shelf up at front, then lift it up and out
of tracks on the rear wall of the refrigerator.
To replace shelves: Select the
desired shelf height. With shelf
front raised slightly, engage top
hooks in tracks at rear of cabinet.
Then lower front of shelf until it
locks into position.
Tempered glass shelves (on
some models) are adjustable in
the same manner.
2
Lift up and out
1
Tilt up
Engage
top hook
Lower to lock
into place
1
2
Porta-Bins on the Doors (on some models)
Adjustable Porta-Bins on fresh
food and frozen food storage compartment
doors can easily be carried from the
refrigerator to the work area.
To remove: Slide Porta-Bin forward on
molded supports until it comes completely
out of the door.
To relocate: Select desired shelf height,
engage Porta-Bins in the molded supports
of the door, and slide in. Porta-Bin will hook in place.
Snuggers are designed
to give you storage flexibility
in Porta-Bins and on your fresh
food door shelves. Items such
as salad dressings, steak sauces
and other condiments can now
be kept securely against the door
liner to help prevent tipping,
spilling or sliding.
Place index finger and middle
finger on either side of the snugger
near the front and simply move it
back and forth to fit your needs.
Snugger
Quick Serve
TM
System (on some models)
Cooking-serving-storage dishes with
durable see-through lids fit into a
rack that hangs on the fresh food or
freezer compartment door. Dishes
can be removed from and returned to
the rack as needed, and the rack can
be removed and relocated on either
door in the same manner as the door bins.
Dishes and lids are safe for use in microwave ovens, refrigerators,
freezers, and are dishwasher-safe.
The dishes should not be used for cooking high-fat foods such as
bacon and high-sugar foods such as candy and syrup. The high
temperatures of the fat and sugar can cause bubbles to form on the
inside of the dish.
CAUTION:
• Dishes and lids are not designed for use in the regular oven,
on the range-top or in the broiler. Such use can be hazardous.
4
Quick Store Bin (on some models)
5
This removable tilt-out bin made of
Lexan polycarbonate resin can be
located on the fresh food or frozen
food storage compartment door. It has
been designed for convenient storage
of those frequently used items that do
not fit easily into a Porta-Bin or soon-
to-be-used items that require covered
storage to keep from drying out.
To open, push the latch up and
pull the bin handle forward.
To avoid damaging the
refrigerator, make sure the bin
is closed and latched before
closing the refrigerator door.
To remove the bin, lift it up and
out of the bin housing.
To relocate the Quick Store unit,
lift the bin housing up and out of the
molded supports on the door, move it
to the desired new location, and
lower it onto the molded supports on
the door. You do not have to remove
the bin from the housing when
relocating the Quick Store unit.
1
2
QUICK S
Pull forward
Push up
ACCESSORIES
Condiment Caddy Beverage Rack
The condiment caddy keeps frequently
used condiments together. It fits in your
refrigerator door shelf. A convenient
handle allows condiments to be easily
carried to the table.
Slide-out beverage rack holds
twelve cans of soda or two
wine/water bottles (lengthwise).
Can be removed for cleaning.
Quick Store Bin
Bin Housing
Shelves Accessories
STORAGE DRAWERS
6
Fruit & Vegetable Drawers Moist’n Fresh Drawer (on some models)
The storage drawers at the bottom of the fresh food compartment are
designed to provide high humidity levels required by most vegetables
and lower humidity levels required for most fruits.
When replacing the drawers, always push them all the way in.
Storage time will depend upon the type of food and its condition when
placed in the drawers.
Excess water that may accumulate in the bottom of the drawers should
be emptied and the drawers wiped dry.
Cool ’n Fresh Drawer (on some models)
This refrigerated drawer is designed to provide lower humidity storage
for items such as:
• Apples • Nectarines • Raspberries
• Apricots • Oranges • Squash, summer
• Grapes • Peaches • Strawberries
• Mushrooms • Pears • Tangerines
This refrigerated drawer is designed to keep unwrapped foods fresh
by retaining the natural moisture content of foods such as:
• Artichokes • Cherries • Peas, green
• Asparagus • Corn • Plums
• Beets, topped • Currants • Radishes
• Blueberries • Greens, leafy • Rhubarb
• Carrots • Lettuce • Spinach
• Celery • Parsley • Tomatoes, ripe
As in any refrigerated storage area, it is recommended that foods
with strong odors be stored wrapped—foods such as:
• Broccoli • Cauliflower • Parsnips
• Brussels sprouts • Green Onions • Turnips
• Cabbage
Adjustable Humidity Drawers (on some models) Snacks Drawer (on some models)
These drawers have individual,
adjustable humidity controls that let
you regulate the amount of cold air
entering the drawers.
Slide the control all the way to the setting and the drawer
provides high humidity recommended for most vegetables.
Slide the control all the way to the setting to provide
lower humidity levels recommended for most fruits.
The slide-out Snacks drawer can
be removed and taken to the sink
or food preparation area. You
may also relocate it and the shelf
to which it attaches within the
fresh food compartment to suit
your storage needs.
7
Adjustable Temperature Meat Drawer (on some models)
Fresh meats are stored best in the coldest part of the refrigerator.
When the drawer is placed in the top 6
slots on the left side and the lever is set at ,
air from the frozen food storage compartment is
forced around the drawer to keep it very cold.
You can move the drawer to any location for storage of items other
than fresh meats.
The variable temperature control lever lets you regulate the amount
of cold air surrounding the drawer.
When the lever is set at , the damper over the opening in
the drawer is fully open to provide the coldest storage area.
When the lever is set at , the damper is fully closed. Normal
refrigerator temperatures will be maintained.
Variable settings between these extremes may be selected.
FREEZER COMPARTMENT
• Food to be frozen must not be placed in direct contact with food in storage.
• Do not store commercially quick-frozen food longer than the time recommended
by the food manufacturers.
• For fastest food freezing, set the frozen food control at position “7.” Since the
compressor will run 100% of the time at this setting, don’t forget to turn back
the setting after the food is frozen.
• If the power to the appliance is shut off for an extended time or if the refrigerating system
fails, do not open the doors unless absolutely necessary. When it is necessary, close them as
quickly as possible so the frozen food will stay frozen as long as possible.
Effervescent drinks should not be stored in the frozen food storage compartment.
Some products such as water ices should not be consumed too cold.
Storage Drawers Freezer Compartment
AUTOMATIC ICEMAKER
(on some models)
8
Your icemaker will produce eight cubes per cycle—approximately
100 cubes in a 24-hour period, depending on frozen food storage
compartment temperature, room temperature, number of door
openings and other use conditions.
If your refrigerator is
operated before the water
connection is made to the
icemaker, keep the feeler arm
in the STOP (up) position.
When the refrigerator is first
installed, allow about 24 hours
for the frozen food storage
compartment to cool down to
icemaking temperatures.
Throw away the first few batches of ice.
This flushes away impurities in the water line.
When the refrigerator has
been connected to the water
supply, move the feeler arm
to the ON (down) position.
Icemaking will continue until the feeler arm senses a sufficient
accumulation of ice cubes in the storage bin and halts the operation
temporarily. For maximum ice storage, level the stored cubes with
your hand occasionally. Be sure nothing interferes with the swing of
the feeler arm.
The icemaker ejects cubes in groups of eight and it is normal for
several cubes to be joined together.
Move the icemaker feeler arm to the STOP (up) position when:
• home water supply is to be off for several hours.
• ice storage bin is to be removed for a period of time.
• going away on vacation, at which time you should also turn off the
valve in the water supply line to your refrigerator.
• turning the fresh food control to “0.”
If ice is not used frequently, old ice cubes will become cloudy
and taste stale. Empty the ice storage bin periodically and wash
it in lukewarm water. Be sure to allow the storage bin to dry before
replacing it—otherwise ice cubes may stick to other parts of
the icemaker.
If this is your first icemaker, you’ll hear occasional sounds that may
be unfamiliar. They are normal icemaking sounds and are not a cause
for concern.
Icemaker
Ice
Storage Bin
Feeler arm in
STOP (up) position
Feeler arm in
ON (down)
position
Water Supply Kit Icemaker Accessory Kit
A kit containing copper tubing, shutoff valve, fittings and
instructions needed to connect the icemaker to your cold water
line is available at extra cost. Contact your local distributor and
order the appropriate kit depending on how much copper tubing
you need. See Preparation section.
If your refrigerator did not come already equipped with an automatic
icemaker, an Icemaker Accessory Kit is available at extra cost from
your local distributor. Check the back of the refrigerator for the
specific icemaker kit needed for your model.
CARE AND CLEANING
Cleaning—Outside
9
The door handles can be cleaned with a cloth dampened with a
solution of mild liquid dishwashing detergent and water. Dry with a
soft cloth. Don’t use wax on the door handles with metal trim.
Keep the finish clean. Wipe with a clean cloth lightly dampened with
kitchen appliance wax or mild liquid dishwashing detergent. Dry and
polish with a clean, soft cloth. Do not wipe the refrigerator with a
soiled dishwashing cloth or wet towel. These may leave a residue that
can erode the paint. Do not use scouring pads, powdered cleaners,
bleach or cleaners containing bleach because these products can
scratch and weaken the paint finish.
Protect the paint finish. The outside of the refrigerator has a high
quality, baked-on paint finish. With proper care, it will stay new-
looking and rust-free for years. Apply kitchen/appliance wax when
the refrigerator is new and then at least twice a year.
Cleaning—Inside
Clean the inside of the fresh food and frozen food storage
compartments at least once a year. Unplug refrigerator before
cleaning. If this is not practical, wring excess moisture out of sponge
or cloth when cleaning around switches, lights or controls. Apply an
appliance wax/polish to the inside surface between the doors.
Use warm water and baking soda solution—about 15 ml of baking
soda to one liter of water. This both cleans and neutralizes odors.
Rinse thoroughly with water and wipe dry.
Avoid cleaning cold glass shelves (on some models) with hot water
because the extreme temperature difference may cause them to break.
Other parts of the refrigerator—including door gaskets, vegetable
drawers, ice trays and all plastic parts—can be cleaned the same way.
After cleaning the door gaskets, apply a thin layer of petroleum jelly
to the door gaskets at the hinge side. This helps keep the gaskets from
sticking and bending out of shape. Do not use cleansing powders or
other abrasive cleaners.
To help prevent odors, leave an open box of baking soda in the
rear of the refrigerator, on the top shelf. Change the box every three
months. An open box of baking soda in the frozen food storage
compartment will absorb stale frozen food storage compartment odors.
Quick Serve dishes and lids can be cleaned in an automatic
dishwasher or by hand with liquid dishwashing detergent and water.
You can remove stains by soaking them in a bleach and water
solution—1 part chlorine bleach to 3 parts water. (Stubborn stains
may require soaking.) Use a plastic scouring pad to remove burned-on
soil. Do not use cleansing powders or other abrasive cleaners.
Do not wash any of your refrigerator’s plastic parts in your
automatic dishwasher.
Under Refrigerator Behind Refrigerator
For most efficient operation, you
need to keep the area under the
refrigerator clean. Turn the
temperature control to “0.”
Remove the base grille. Sweep
away or vacuum dust that is readily
accessible on the condenser coils,
then turn the control back on.
For best results, use a brush
specially designed for this purpose,
available from your local distributor.
This easy cleaning operation should
be done at least once a year.
Care should be taken in moving your refrigerator away from the wall.
All types of floor coverings can be damaged, particularly cushioned
coverings and those with embossed surfaces.
Pull the refrigerator straight out and return it to position by pushing
it straight in. Moving your refrigerator in a side direction may
result in damage to your floor covering or refrigerator. Refer to
the Rollers section.
Clean the condenser coils at
least once a year.
Storage Drawer and Drawer Cover Removal
Drawers at the bottom of the fresh food compartment will stop
before coming all the way out of the refrigerator, to help prevent
contents from spilling onto the floor. These drawers can be removed
easily by lifting the sides up slightly while pulling the drawers past
the ‘‘stop’’ location.
To remove the drawers and their covers when the fresh food
compartment door cannot be opened fully, follow the procedure that
applies to your model.
(continued next page)
Automatic Icemaker Care and Cleaning
CARE AND CLEANING
(continued)
10
Two Drawers (on some models)
1. Remove the drawer farthest
from the door.
2. Remove the other drawer.
On models with a bottom
door shelf that blocks the
other drawer, slide the other
drawer toward the middle
and remove it.
3. Remove the glass cover. Reach
in, push the front of the glass
cover up and, at the same time,
pull it forward as far as it will
come. Tilt it and take it out.
4. Remove the drawer frame
(Always remove the glass
cover before you take out the
drawer frame.)
Lift the frame off the supports
at each side and back, pull it
forward, tilt it and take it out.
To replace:
1. Lower the frame until it rests
on the supports at each side
and back.
2. Replace the drawers.
If you removed the drawer slide,
replace it with the sloped end at
the front.
a. Slide one side of the drawer
onto the drawer slide.
b. Move the slide and drawer all
the way to the hinge side until
the other side of the drawer rests
on the frame.
c. Slide the other drawer into place.
3. Replace the glass cover, pushing its rear edge firmly into the rear
frame channel and gently lowering the front into place.
Frame
Drawer Slide
(sloped end)
Light Bulb Replacement
A light bulb and socket are located at the top of the fresh food
compartment opposite the temperature control panel.
Some models also have a bulb and socket in the upper left corner of
the frozen food storage compartment behind a removable light shield.
To replace either bulb, unplug the refrigerator from its electrical
outlet and remove the light shield by pulling down on the shield at
the bulb end. When the bulb cools, unscrew it and replace it with a
similar size bulb.
When replacing the light
shield make sure the tab
is placed in the groove
of the light shield holder.
Then rotate the shield
back and up until the
shield snaps into place.
Tab
Groove
PREPARATION
11
Clearances Water Supply to Icemaker (on some models)
Allow the following clearances for ease of installation, proper air
circulation and plumbing and electrical connections:
Sides..........................................................................19 mm
Top.............................................................................25 mm
Back...........................................................................25 mm
If Model 19, 22, or 25 is to be installed against a wall on the hinge side,
allow 38 mm for door clearance.
If your refrigerator has an icemaker, or if you plan to add an
icemaker later, the icemaker will have to be connected to a cold
drinking water line.
A water supply kit containing copper tubing, shutoff valve, fittings
and instructions is available at extra cost from your local distributor.
There should be sufficient tubing from the cold water supply to the
icemaker inlet to allow moving the refrigerator out from the wall
several feet (approximately 244 cm of 1/4
² copper tubing in three
25 cm diameter coils).
Do not use kits with plastic tubing since there is water pressure in the
supply line at all times.
Maximum permissible inlet water pressure—8.3 bars.
Minimum permissible inlet water pressure—1.4 bars.
Installation of icemaker must be made by a qualified service technician.
Rollers
Some models have adjustable rollers that allow you to move the
refrigerator away from the wall for cleaning. Rollers should be set so
the refrigerator is firmly positioned on the floor and the front is raised
just enough (about 19 mm from the floor) that the doors close easily
when opened about halfway.
Remove the base grille by
grasping the bottom of the grille
and pulling it out.
Turn the two front roller adjusting screws
clockwise to raise the refrigerator,
counterclockwise to lower it.
To replace the base grille, line
up the clips on the back of the
grille with the openings in the
base plate and push the grille
forward until it snaps into place.
When You Go on Vacation When You Move
For shorter vacations, remove perishable foods and leave controls at
regular settings. However, if room temperature is expected to drop
below 16°C, follow the same instructions as for extended vacations.
For extended vacations or absences, shut off the power to the
refrigerator, move the fresh food control to the “0” position, and
clean the interior with a baking soda solution of 15 ml of baking soda
to one liter of water. Wipe dry. To prevent odors, leave an open box of
baking soda in the refrigerator. Leave doors open.
Move icemaker feeler arm to STOP (up) position and be sure to shut
off water supply to the refrigerator.
Disconnect power cord from wall outlet, remove all food, and clean
and dry the interior.
Secure all loose items such as grille, shelves and storage pans by
taping them securely in place to prevent damage.
Be sure refrigerator stays in
upright position during actual moving and
in van. Refrigerator must be secured in van to prevent movement.
Protect outside of refrigerator with blanket.
Dimensions
Model 18 19 21 22 24 25
A* 163 cm 163 cm 168 cm 168 cm 170 cm 170 cm
B 75 cm 75 cm 79 cm 79 cm 87 cm 87 cm
C** 80 cm 83 cm 80 cm 83 cm 80 cm 83 cm
D 147 cm 147 cm 152 cm 152 cm 160 cm 160 cm
E 70 cm 70 cm 70 cm 70 cm 70 cm 70 cm
* Height does not include hinge—Add 22 mm for hinge.
** Depth includes handle.
A
B
C
D
E
Care and Cleaning Preparation
12
INSTALLATION REQUIREMENTS
IMPORTANT…Please Read Carefully
Electrical Requirements
The refrigerator should always be plugged into its own individual
electrical outlet— Please refer to the rating plate on the refrigerator
for the correct voltage and frequency. This is recommended for best
performance and to prevent overloading house wiring circuits, which
could cause a fire hazard from overheated wires.
WARNING: HOW TO AVOID ACCIDENTS TO CHILDREN.
WHEN DISCARDING AN OLD REFRIGERATOR OR
FREEZER BE CERTAIN TO MAKE THE LOCK UNUSABLE.
IF POSSIBLE, REMOVE THE DOORS AND DISCARD
SEPARATELY. DO NOT ATTEMPT TO STAND ON TOP OF
YOUR APPLIANCE. IT IS NOT DESIGNED FOR SUCH USE
AND YOU COULD INJURE YOURSELF OR DAMAGE THE
APPLIANCE BY SUCH ABUSE. CHILDREN SHOULD NOT
BE ALLOWED TO PLAY WITH THE APPLIANCE OR
TAMPER WITH THE CONTROLS.
How to Connect Electricity
For personal safety, this appliance must be
properly earthed.
The power cord of this appliance
is equipped with an earthing plug
which mates with a standard
earthed wall outlet to minimize
the possibility of electric shock
hazard from this appliance.
Have the wall outlet checked
by a qualified electrician to make
sure the outlet is properly earthed.
Where an unearthed wall outlet is encountered, it is your personal
responsibility and obligation to have it replaced with a properly
earthed wall outlet.
If the plug does not fit your outlet a new plug can be fitted.
IMPORTANT: In some countries the refitting of electric plugs
and cables is only permitted when the work is completed by a
qualified technician.
If the power supply cord becomes damaged, it must be replaced by a
qualified service agent in order to avoid a safety hazard.
Insure proper
earthing exists
before using.
Earthing Plug
13
Installation
INSTALLATION INSTRUCTIONS
FOR GREAT BRITAIN AND IRELAND ONLY
IMPORTANT: Fitting a Different Plug
The wires in the mains lead are coloured in accordance with the
following code: Green and Yellow—Earth; Blue—Neutral; Brown—
Live. If you fit your own plug the colours of these wires may not
correspond with the identifying marks on the plug terminals. This is
what you have to do:
1. Connect the green and yellow
(Earth) wire to the terminal
in the plug marked ‘E’ with
the symbol or coloured green
or green and yellow.
2. Connect the blue (Neutral) wire
to the terminal in the plug
marked ‘N’ or coloured black.
3. Connect the brown (Live) wire to
the terminal marked ‘L’ or
coloured red.
With alternative plug a 15A fuse must be fitted either in the plug or
adapter or in the main fuse box. In the event of replacing a fuse in the
plug supplied, a 13A ASTA approved fuse to BS1362 must be fitted.
If the plug is the moulded-on type the fuse cover must be refitted
when changing the fuse. In the event of losing the fuse cover the plug
must not be used until a replacement fuse cover has been obtained and
fitted. A new fuse cover can be obtained from your nearest Service
Centre or local Electricity Board. The colour of the correct
replacement fuse cover is that of the coloured marks or insert in the
base of the plug.
E
13 AMP
L
N
Mains Lead Replacement
If the mains lead on this appliance needs replacing at any time, it must be replaced by a
special lead which is obtainable from your nearest Service centre. A charge will be made for
the replacement of the mains lead if you have damaged the lead.
Green
Yellow
Blue
Brown
Cord Grip
Electrical Requirements
We recommend that this appliance is connected to the mains supply via a suitable switched
socket in a readily accessible position. All appliances come complete with a fitted plug.
The plug on your refrigerator has a 13A fuse. If the plug does not fit your sockets, a new
plug can be fitted. Cut off the old plug and throw it away, do not insert it into a socket
elsewhere in the house as this could cause a shock.
WARNING: THIS APPLIANCE MUST BE EARTHED.
14
WATER LINE INSTALLATION
CAUTION:
• If you use your refrigerator before connecting
the water line, make sure the icemaker feeler arm
is kept in the STOP (up) position.
• Do not install the icemaker tubing in areas
where temperatures fall below 0°C.
•When using any electrical device (such as a
power drill) during installation, be sure the device
is insulated or wired in a manner to prevent the
hazard of electric shock.
• All installations must be in accordance with
local plumbing code requirements.
WARRANTY INFORMATION
This water line installation is not warranted by
the refrigerator or icemaker manufacturer.
Follow these instructions carefully to minimize
the risk of expensive water damage.
SHUT OFF THE MAIN WATER SUPPLY.
Turn on the nearest faucet long enough to clear
the line of water.
1
INSTALL THE SHUTOFF VALVE ON THE
NEAREST FREQUENTLY USED DRINKING
WATER LINE.
a. Choose a location for the valve that is easily
accessible. It is best to connect into the side of
a vertical water pipe. When it is necessary to
connect into a horizontal water pipe, make the
connection to the top or side, rather than at the
bottom, to avoid drawing off any sediment from
the water pipe.
b. Drill a 1/4
² hole in the water pipe, using a
sharp bit. Remove any burrs resulting from
drilling the hole in the pipe. (Do not drill
a hole if the valve is a self-piercing type.)
c. Fasten the shutoff valve to the cold water pipe
with the pipe clamp.
d. Tighten the
clamp screws until the
sealing washer
begins to swell. Do
not overtighten or
you may crush the
copper tubing.
2
WHAT YOU WILL NEED
• A cold water supply is required for automatic
icemaker operation. The water pressure must be
between 1.4 and 8.3 bars.
•
Power drill, unless you have a self-piercing valve.
• Copper tubing, 1/4² outer diameter to connect
the refrigerator to the water supply. Be sure both
ends of the tubing are cut square.
To determine how much copper tubing you need:
measure the distance from the water valve on the
back of the refrigerator to the water supply pipe.
Then add 244 cm. Be sure there is sufficient extra
tubing (about 244 cm coiled into 3 turns of about
25 cm diameter) to allow the refrigerator to move
out from the wall after installation. Do not use
plastic tubing or plastic fittings because the water
supply line is under pressure at all times. Also,
certain types of plastic tubing may become brittle
with age and crack, resulting in water leakage.
• Shutoff valve to connect to the cold water line.
The shutoff valve should have a water inlet with a
minimum inside diameter of 5/32² at the point of
connection to the COLD WATER LINE. Saddle-
type shutoff valves are included in many water
supply kits. Before purchasing, make sure a
saddle-type valve complies with your local
plumbing codes.
• Two 1/4² outer diameter compression nuts
and 2 ferrules (sleeves)—to connect the copper
tubing to the shutoff valve and the refrigerator
water valve.
• If your existing water line has a flared fitting at
the end, you will need an adapter (available at
plumbing supply stores) to connect the water line
to the refrigerator OR—you can cut off the flared
fitting with a tube cutter and then use a
compression fitting.
Typical ways to connect to water supply
Under sink
to cold
water pipe
Through wall to
utility room cold
water pipe
In crawl
space under
house
Through floor
to basement
cold water pipe
Pipe
Clamp
Saddle-Type
Shutoff
Valve
Washer
Inlet
End
Vertical
Cold Water
Pipe
15
ROUTE THE COPPER TUBING BETWEEN THE
COLD WATER LINE AND THE REFRIGERATOR.
Route the tubing through a hole drilled in the
floor or wall (behind the refrigerator or adjacent
base cabinet) as close to the wall as possible. Be
sure there is sufficient extra tubing (about 244 cm
coiled into 3 turns of about 25 cm diameter) to
allow the refrigerator to move out from the wall
after installation.
3
a. Remove the
plastic flexible
cap from the
water valve.
b. Place the
compression
nut and ferrule
(sleeve) onto the
end of the tubing
as shown.
c. Insert the end
of the copper
tubing into the water valve connection as far as
possible. While holding the tubing, tighten the
fitting.
d. Fasten the copper tubing into the clamp
provided to hold it in a vertical position. You may
need to pry open the clamp.
TURN THE WATER ON AT THE
SHUTOFF VALVE.
Tighten any connections that leak.
7
PLUG THE REFRIGERATOR POWER CORD
INTO AN EARTHED ELECTRICAL OUTLET.
8
MOVE THE REFRIGERATOR BACK TO
THE WALL.
Arrange the coil of copper tubing so that it does
not vibrate against the back of the refrigerator or
against the wall.
10
SET THE ICEMAKER FEELER ARM TO THE ON
(DOWN) POSITION.
The icemaker will not begin to operate until it
reaches its operating temperature of -9°C or
below. It will then begin operation automatically if
the icemaker is in the ON (down) position.
NOTE: The icemaker may double-cycle when it
first starts, causing some water spillage from the
icemaker into the ice bucket. This is normal and
should not happen again. The first few batches of
cubes should be thrown away, so that remaining
impurities in the water line will be flushed out.
9
CONNECT THE COPPER TUBING TO THE
SHUTOFF VALVE.
Place the compression
nut and ferrule
(sleeve) onto the
end of the tubing
and connect it to the
shutoff valve. Make
sure the tubing is fully
inserted into the valve.
Tighten the compression
nut securely.
4
TURN ON THE WATER AND FLUSH OUT
THE TUBING.
a. Turn the main water supply on and flush out
the tubing until the water is clear.
b. Shut the water off at the water valve after
about one liter of water has been flushed through
the tubing.
5
CONNECT THE COPPER TUBING TO
THE REFRIGERATOR.
Before making the connection to the
refrigerator, be sure the refrigerator power
cord is not plugged into the wall outlet.
We recommend installing a water filter (available
from your local distributor) if your water supply
has sand or particles that could clog the screen of
the refrigerator’s water valve. Install it in the
water line near the refrigerator.
6
Saddle-Type
Shutoff
Valve
Packing
Nut
Outlet
Valve
Compression Nut
Ferrule
(sleeve)
Ferrule
(sleeve)
1/4² Copper Tubing
1/4² Compression Nut
Tubing
Clamp
Refrigerator Connection
REVERSING THE DOOR SWING
16
NOTE: DOORS ON DISPENSER MODELS
DO NOT REVERSE.
When reversing the door swing:
• Read the instructions all the way through
before starting.
• Handle parts carefully to avoid scratching paint.
• Set screws down by their related parts to avoid
using them in the wrong places.
• Provide a non-scratching work surface for
the doors.
REMOVE FROZEN FOOD STORAGE
COMPARTMENT DOOR.
a. Tape the door shut with masking tape.
b. With a Phillips screwdriver,
remove the hinge cover (on
some models). With a
Torxdriver, remove 2 Torx
screws that hold the top hinge
to the cabinet.
c. Lift the hinge straight up
to free the hinge pin from the
socket in the top of the door.
d. Remove tape, tilt the door
away from the cabinet and lift it to free its
bottom socket from the hinge pin on the center
hinge bracket.
e. Set the door on a non-scratching surface
with the outside up.
2
IMPORTANT: Once you begin, do not move
cabinet until door-swing reversal is completed.
These instructions are for changing the
hinges from the right side to the left side.
If you ever want to change the hinges back to the
right side, follow these same instructions (merely
reverse all references to left and right).
REMOVE FRESH FOOD DOOR.
a. Tape the door shut
with masking tape.
b. Remove the hinge
pin with a 3/8
² socket
and ratchet.
c. Remove tape and tilt
the door away from the
cabinet. Remove and
save the washer on the
hinge pin.
d. Lift the door
straight up to
free its bottom socket
from the pin in the
bottom hinge bracket.
3
TOOLS REQUIRED
• Phillips screwdriver
• Masking tape
• T20 or T25 Torxdriver, whichever
your model requires
• Putty knife or thin-blade screwdriver
• 3/8² socket and ratchet
(a 6-point socket is recommended)
GENERAL
a. Unplug the refrigerator from its
electrical outlet.
b. Empty all door shelves, including the
dairy compartment.
CAUTION: Do not let either door drop to the
floor. To do so could damage the door stop.
1
REMOVE THE DOORS
Plastic
Washer
Hinge
Pin
Center
Hinge
Bracket
Fresh Food Door
17
TRANSFER BOTTOM HINGE BRACKET TO THE LEFT.
a. Remove the base grille. Grasp it at the bottom
and pull it straight out.
b. Using a Torxdriver, remove the hinge bracket
and plastic washer from the bottom right side
of the cabinet.
c. Reinstall the hinge bracket and plastic
washer to the bottom left side of the cabinet.
1
TRANSFER CENTER HINGE BRACKET TO THE LEFT.
a. Remove the center hinge bracket by removing
the three Torx screws. NOTE: Keep these
screws with the hinge bracket. They are
longer screws and will be used when
installing the hinge on the other side.
b. Remove the three Torx screws from the center
left side of the cabinet. Screw them into the holes
on the right side, which were uncovered in Step
(a) above.
Place the center hinge bracket over the holes at the
center left side of the cabinet, insert the three
screws that were removed with the center hinge
bracket in Step (a) and tighten them.
2
TRANSFER TOP HINGE TO THE LEFT.
Interchange hinge and screws at top right with
screws at top left of cabinet. Do not tighten
screws on hinge side at this time.
3
TRANSFER DOOR STOPS.
a. On each door, move the metal door stop from
the right end to the left end.
b. Move any screws from the left end to the
right end.
4
Plastic washer
Bottom left
Center left
Center right
Do not remove this screw
Do not remove this screw
Bottom right
Plastic washer
REVERSE HARDWARE ON CABINET
(continued next page)
REVERSING THE DOOR SWING
(continued)
18
TRANSFER FRESH FOOD DOOR HANDLE
TO THE RIGHT.
To remove handle…
• Remove handle plug using
putty knife under edge, and
remove screw underneath.
• Remove two screws holding
handle to top of door.
After removing
handle…
• Remove small plug
buttons from right edge
of door top and insert
them into handle screw
holes on left side.
• Remove large plug
button from left edge of
door and insert it into
hole on opposite side.
• Transfer medallion on
door to opposite side.
When reinstalling handle…
• Attach handle to right side of door with screws
at top and under handle plug.
1
TRANSFER FROZEN FOOD STORAGE
COMPARTMENT DOOR HANDLE TO THE RIGHT.
• Remove one screw holding handle to top of door
and two screws holding handle to bottom of door.
• Remove handle.
• Remove plug button from right edge of door
and insert it into handle screw hole on left side.
• Attach handle on the opposite side using the
holes closest to the edge of door.
2
REVERSE DOOR HANDLES
Large Plug Button
Medallion
Small Plug
Buttons
Models with long handles have a pin that
fits into a hole at the bottom of the door.
Hole
Handle Plug
Pin
Handle Plug
19
a. Lower bottom socket of fresh food door
onto pin on bottom hinge bracket. Be sure
washer is in place.
b. Tilt door toward cabinet and gently push
door under center hinge bracket and align
with the hole in the center hinge bracket.
c. Reinstall hinge
pin with a 3/8
²
socket and ratchet
so it extends
through hole in
center hinge
bracket and into
socket on top of
fresh food door.
a. Lower bottom socket of frozen food
storage compartment door onto center hinge
pin. Be sure washer is in place.
b. Tilt door toward cabinet, lifting the top
hinge so the pin fits into the socket on top of
the door.
c. Tighten the top hinge screws after
supporting the door on the handle side and
aligning so the gap between the doors is even all
across the front.
REHANG FRESH FOOD DOOR REHANG FROZEN FOOD STORAGE
COMPARTMENT DOOR
Plastic
Washer
Plastic
Washer
Hinge Pin
Fresh Food Door
Center
Hinge
Bracket
Plastic Washer
Center Hinge Pin
PROBLEM POSSIBLE CAUSE
REFRIGERATOR DOES • May be in defrost cycle when motor does not operate for about 30 minutes.
NOT OPERATE
• Temperature control is in “0” position.
• If interior light is not on, refrigerator may not be plugged in at wall outlet.
• If plug is secure and the refrigerator still fails to operate, plug a lamp or a small
appliance into the same outlet to determine if there is a tripped circuit breaker or
burned-out fuse.
MOTOR OPERATES • Modern refrigerators with more storage space and a larger frozen food storage
FOR LONG PERIODS compartment require more operating time.
• Normal when refrigerator is first delivered to your home—usually requires
24 hours to completely cool down.
• Large amounts of food placed in refrigerator to be cooled or frozen.
• Hot weather—frequent door openings.
• Door left open.
• Temperature control is set too cold. Refer to Temperature Control section.
• Grille and condenser need cleaning. Refer to Care and Cleaning section.
MOTOR STARTS AND • Temperature control starts and stops motor to maintain even temperatures.
STOPS FREQUENTLY
VIBRATION OR RATTLING • If refrigerator vibrates, more than likely it is not resting solidly on the floor.
The front leveling legs need adjusting, or floor is weak or uneven. Refer to
Rollers in the Preparation section.
• If dishes vibrate on shelves, try moving them. Slight vibration is normal.
QUESTIONS?
USE THIS PROBLEM SOLVER
NORMAL OPERATING SOUNDS
These sounds are normal and are due mostly to highly efficient operation.
Icemaker (on some models).
Occasionally you will hear ice cubes
dropping into the ice bin.
Evaporator Fan. You may hear air being forced through the cabinet by the fan.
Evaporator. The flow of refrigerant through the evaporator may create a
boiling or gurgling sound.
Defrost Heater. During defrost cycles, water dripping onto the heater may
cause a hissing or sizzling sound. After defrosting, a popping sound may occur
and the evaporator may create a boiling or gurgling sound.
Cold Control & Defrost Timer. These parts can produce a snapping sound
when turning the refrigerator on or off. The timer also produces a sound similar
to an electric clock.
Plastic Liner. Cracking or popping sounds due to expansion of the plastic liner.
Condenser Fan. You may hear air being forced over the condenser by the fan.
Compressor. Modern, high efficiency compressors operate much faster than
older models. The compressor may have a high pitched hum or pulsating sound.
Water Valve (on models equipped with an automatic icemaker). When
the icemaker fills with water, a buzzing sound and running water will be heard.
Water Pan. Water may be heard running into the drain pan during the
defrost cycle.
Depending on the placement of the refrigerator in your kitchen, you may want to
place a piece of rubber-backed carpet under the refrigerator to reduce the noise.
20
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
-
1
-
2
-
3
-
4
-
5
-
6
-
7
-
8
-
9
-
10
-
11
-
12
-
13
-
14
-
15
-
16
-
17
-
18
-
19
-
20
-
21
-
22
-
23
-
24
-
25
-
26
-
27
-
28
-
29
-
30
-
31
-
32
-
33
-
34
-
35
-
36
-
37
-
38
-
39
-
40
-
41
-
42
-
43
-
44
-
45
-
46
-
47
-
48
-
49
-
50
-
51
-
52
-
53
-
54
-
55
-
56
-
57
-
58
-
59
-
60
-
61
-
62
-
63
-
64
-
65
-
66
-
67
-
68
dans d''autres langues
- English: GE TBI18JIBWW User guide
- español: GE TBI18JIBWW Guía del usuario