Cameo PIXBAR® TW IP G2 Manuel utilisateur

USER´S MANUAL

BEDIENUNGSANLEITUNG

MANUEL D`UTILISATION

MANUAL DE USUARIO

INSTRUKCJA OBSŁUGI

MANUALE D‘ USO

PIXBAR® G2

TUNABLE WHITE LED PIXBAR IP65

CLPBTWIPG2

CONTENTS / INHALTSVERZEICHNIS / CONTENU /

CONTENIDO / TREŚĆ / CONTENUTO

ENGLISH

INFORMATION ON THIS USER MANUAL 6

INTENDED USE 6

DEFINITIONS AND SYMBOL EXPLANATIONS 6

SAFETY INSTRUCTIONS 7

NOTES ON PORTABLE OUTDOOR DEVICES 10

PACKAGING CONTENT 11

INTRODUCTION 11

CONNECTIONS, OPERATING AND DISPLAY ELEMENTS 12

OPERATION 14

INSTALLATION 23

FROST FILTER 26

GLARE SHIELD 27

CARE, MAINTENANCE AND REPAIR 27

OPTIONAL ACCESSORIES 28

DIMENSIONS 29

TECHNICAL DATA 30

EXPLANATION OF IP PROTECTION CLASS 31

MINIMUM DISTANCE TO ILLUMINATED SURFACE 32

MINIMUM DISTANCE TO NORMALLY FLAMMABLE MATERIALS 32

DISPOSAL 32

MANUFACTURER’S DECLARATIONS 33

DEUTSCH

INFORMATIONEN ZU DIESER BEDIENUNGSANLEITUNG 34

BESTIMMUNGSGEMÄSSER GEBRAUCH 34

BEGRIFFS- UND SYMBOLERKLÄRUNGEN 34

SICHERHEITSHINWEISE 35

HINWEISE FÜR ORTSVERÄNDERLICHE OUTDOOR-GERÄTE 39

LIEFERUMFANG 39

EINFÜHRUNG 39

ANSCHLÜSSE, BEDIEN- UND ANZEIGEELEMENTE 40

BEDIENUNG 42

MONTAGE 52

FROSTFILTER 55

BLENDSCHUTZ 56

PFLEGE, WARTUNG UND REPARATUR 56

OPTIONALES ZUBEHÖR 57

ABMESSUNGEN 58

TECHNISCHE DATEN 59

ERLÄUTERUNGEN ZUR IP-SCHUTZART 61

MINDESTABSTAND ZUR BELEUCHTETEN FLÄCHE 61

MINDESTABSTAND ZU NORMAL ENTFLAMMBAREN MATERIALIEN 61

ENTSORGUNG 62

HERSTELLERERKLÄRUNGEN 62

FRANÇAIS

INFORMATIONS SUR CE MANUEL D'UTILISATION 64

UTILISATION PRÉVUE 64

DÉFINITIONS ET EXPLICATION DES PICTOGRAMMES 64

CONSIGNES DE SÉCURITÉ 65

NOTES SUR LES APPAREILS PORTABLES POUR EXTÉRIEUR 69

CONTENU DU CARTON 69

INTRODUCTION 69

CONNECTEURS, UTILISATION ET INDICATEURS 70

UTILISATION 72

INSTALLATION 82

FILTRE FROST 85

ÉCRAN ANTI-ÉBLOUISSEMENT 86

ENTRETIEN, MAINTENANCE ET RÉPARATION 86

ACCESSOIRES EN OPTION 87

DIMENSIONS 88

CARACTÉRISTIQUES TECHNIQUES 89

EXPLICATION DE LA CLASSE DE PROTECTION IP 91

DISTANCE MINIMALE PAR RAPPORT À LA SURFACE ÉCLAIRÉE 92

DISTANCE MINIMALE PAR RAPPORT AUX MATÉRIAUX INFLAMMABLES ORDINAIRES 92

MISE AU REBUT 92

DÉCLARATIONS DU FABRICANT 93

ESPAÑOL

INFORMACIÓN SOBRE ESTE MANUAL DE USUARIO 94

USO PREVISTO 94

DEFINICIONES Y EXPLICACIONES DE LOS SÍMBOLOS 94

INSTRUCCIONES DE SEGURIDAD 95

INDICACIONES PARA EQUIPOS PORTÁTILES DE EXTERIOR 99

ELEMENTOS SUMINISTRADOS 99

INTRODUCCIÓN 99

CONEXIONES, CONTROLES E INDICADORES 100

OPERACIÓN 101

MONTAJE 111

FILTRO FROST 115

PROTECCIÓN ANTIRREFLEJO 116

CUIDADO, MANTENIMIENTO Y REPARACIÓN 116

ACCESORIOS OPCIONALES 117

DIMENSIONES 118

CARACTERÍSTICAS TÉCNICAS 119

EXPLICACIÓN SOBRE LA CLASE DE PROTECCIÓN IP 121

DISTANCIA MÍNIMA A LA SUPERFICIE ILUMINADA 121

DISTANCIA MÍNIMA A MATERIALES NORMALMENTE INFLAMABLES 122

ELIMINACIÓN 122

DECLARACIÓN DEL FABRICANTE 122

POLSKI

INFORMACJE NA TEMAT NINIEJSZEJ INSTRUKCJI OBSŁUGI 124

ZAMIERZONE ZASTOSOWANIE 124

DEFINICJE I OBJAŚNIENIA SYMBOLI 124

INSTRUKCJE BEZPIECZEŃSTWA 125

UWAGI DOTYCZĄCE PRZENOŚNYCH URZĄDZEŃ DO ZASTOSOWAŃ ZEWNĘTRZNYCH 129

ZAWARTOŚĆ OPAKOWANIA 129

WPROWADZENIE 129

PRZYŁĄCZA, ELEMENTY OBSŁUGI I WSKAŹNIKI 130

OBSŁUGA 132

INSTALACJA 142

FILTR FROST 145

OSŁONA PRZECIWODBLASKOWA 146

PIELĘGNACJA, KONSERWACJA I NAPRAWA 146

AKCESORIA OPCJONALNE 147

WYMIARY 148

DANE TECHNICZNE 149

WYJAŚNIENIE KLASY OCHRONY IP 151

MINIMALNA ODLEGŁOŚĆ OD OŚWIETLANEJ POWIERZCHNI 151

CONTENTS / INHALTSVERZEICHNIS / CONTENU /

CONTENIDO / TREŚĆ / CONTENUTO

MINIMALNA ODLEGŁOŚĆ OD NORMALNIE ŁATWOPALNYCH MATERIAŁÓW: 152

UTYLIZACJA 152

DEKLARACJE PRODUCENTA 152

ITALIANO

INFORMAZIONI SU QUESTO MANUALE D’ISTRUZIONI 154

USO CONFORME 154

SPIEGAZIONE DI TERMINI E SIMBOLI 154

INDICAZIONI SULLA SICUREZZA 155

AVVERTENZE PER DISPOSITIVI PORTATILI PER ESTERNI 159

DOTAZIONE 159

INTRODUZIONE 159

CONNESSIONI, ELEMENTI DI COMANDO E INDICATORI 160

UTILIZZO 161

MONTAGGIO 171

FILTRO FROST 175

PROTEZIONE ANTIRIFLESSO 176

CURA, MANUTENZIONE E RIPARAZIONE 176

ACCESSORI OPZIONALI 177

DIMENSIONI 178

DATI TECNICI 179

SPIEGAZIONI SULLA CLASSE DI PROTEZIONE IP 181

DISTANZA MINIMA DALLA SUPERFICIE ILLUMINATA 181

DISTANZA MINIMA DA MATERIALI NORMALMENTE INFIAMMABILI 181

SMALTIMENTO 182

DICHIARAZIONI DEL FABBRICANTE 182

DMX CONTROL / DMX STEUERUNG / PILOTAGE DMX /

CONTROL DMX / STEROWANIE DMX / CONTROLLO DMX 183

6

DMX

ITALIANO

POLSKI

ESPAÑOL

FRANCAIS

DEUTSCHENGLISH

ENGLISH

YOU HAVE MADE THE RIGHT CHOICE!

This device has been developed and manufactured to the highest quality standards to ensure

many years of trouble-free operation. Please read this user manual carefully to be able to quickly

put your new Cameo Light product to optimum use. Further information about Cameo Light is

available on our website CAMEOLIGHT.COM.

INFORMATION ON THIS USER MANUAL

• Carefully read the safety instructions and the entire manual before operating the device.

• Observe the warnings on the device and in the user manual.

• Always keep the user manual within reach.

• If you sell or pass on the device, it is important that you also include this user manual, as it is an

integral part of the product.

INTENDED USE

The product is a device for event technology!

This product has been developed for professional use in the field of event technology and is not

suitable for use as domestic lighting!

Furthermore, this product is only intended for qualified users with specialist knowledge of

event technology!

Use of the product outside the specified technical data and operating conditions is considered

improper use!

Liability is exempted when damage and third-party damage to persons and property is caused by

inappropriate use!

The product is not suitable for:

• Use by persons (including children) with limited physical, sensory or mental abilities or lack of

experience and knowledge.

• Children (children must be instructed not to play with the device).

DEFINITIONS AND SYMBOL EXPLANATIONS

1. DANGER: The word DANGER, possibly in combination with a symbol, indicates immediately

dangerous situations or conditions for life and limb.

2. WARNING: The word WARNING, possibly in combination with a symbol, indicates potentially

dangerous situations or conditions for life and limb.

3. CAUTION: The word CAUTION, possibly in combination with a symbol, is used to indicate situa-

tions or conditions that may lead to injury.

4. ATTENTION: The word ATTENTION, possibly in combination with a symbol, refers to situations

or conditions that can lead to damage to property and/or the environment.

7

DMX DEUTSCHFRANCAIS

ESPAÑOL ENGLISH

ITALIANO POLSKI

This symbol identiﬁes hazards that can cause electric shock.

This symbol identiﬁes hazardous areas or hazardous situations.

This symbol indicates hazards caused by hot surfaces.

This symbol indicates hazards caused by intense light sources.

This symbol indicates a device in which there are no user-replaceable parts.

This symbol indicates additional information on the operation of the product.

SAFETY INSTRUCTIONS

DANGER:

1. Do not open or modify the device.

2. If your device no longer functions properly, if liquids or objects get inside it or if it

has been damaged in any other way, switch it off immediately and disconnect it

from the mains. The device may be repaired only by authorised repair technicians.

3. For devices of protection class 1, the protective earth conductor must be connected

correctly. Never disconnect the protective earth conductor. Devices of protection

class 2 do not have a protective earth conductor.

4. Ensure that live cables are not kinked or otherwise mechanically damaged.

5. Never bypass the device fuse.

WARNING:

1. The device may not be operated if it shows obvious signs of damage.

2. The device may only be installed in a voltage-free state.

3. If the power cable of the device is damaged, do not operate the device.

4. Permanently connected power cables may only be replaced by a qualified person.

ATTENTION:

1. Do not operate the device if it has been exposed to large temperature fluctuations

(for example, after transport). Moisture and condensation can damage the device.

Switch on the device only when it has reached ambient temperature.

8

DMX

ITALIANO

POLSKI

ESPAÑOL

FRANCAIS

DEUTSCHENGLISH

2. Make sure that the voltage and frequency of the mains supply correspond to the

values indicated on the device. If the device has a voltage selector switch, do not

turn the device on until it has been set correctly. Use only suitable power cables.

3. To disconnect the device from the mains at all poles, it is not sufficient to press the

on/off switch on the device.

4. Make sure that the fuse used corresponds to the type printed on the device.

5. Make sure that appropriate measures have been taken against overvoltage (e.g.

lightning strike).

6. Observe the specified maximum output current on devices with a Power Out

connection. Ensure that the total current consumption of all connected devices

does not exceed the specified value.

7. Only replace plug-in power cables with equivalent cables that correspond to

the cable originally supplied. The cross-section must not be smaller than the

cross-section of the original cable.

8. Connect the device only to compliant, tested and undamaged power outlets.

DANGER:

1. Danger of suffocation! Plastic bags and small parts must be kept out of reach of

persons (including children) with reduced physical, sensory or mental capabilities.

2. Danger caused by falling device! Make sure that the device is securely installed

and cannot fall down. Only use suitable stands or mounts (particularly for fixed

installations). Ensure that accessories are properly installed and secured. Ensure

that all applicable safety regulations are observed.

WARNING:

1. Use the device only in the prescribed manner.

2. Operate the device only with the accessories recommended and intended by the

manufacturer.

3. During installation, observe the safety regulations applicable in your country.

4. After connecting the device, check all cable routes to avoid damage or accidents,

e.g. due to tripping hazards.

5. Always observe the specified minimum distance to normally flammable materials!

Unless explicitly stated, the minimum distance is 0.3 m.

6. Always observe the minimum distance to the illuminated surface specified on the

device!

CAUTION:

1. Moving components such as mounting brackets pose a jamming hazard.

2. In the case of devices with motor-driven components, there is a risk of injury from

the movement of the device. Sudden movement of the device can cause shock

reactions.

9

DMX DEUTSCHFRANCAIS

ESPAÑOL ENGLISH

ITALIANO POLSKI

CAUTION:

3. The exterior surface of the device can become very hot during regular operation.

Ensure that accidental touching of the housing is not possible. Always allow the

device to cool sufficiently before removal, maintenance work and charging etc.

ATTENTION:

1. Do not install and operate the device in the vicinity of radiators, heat accumulators,

ovens, or other heat sources. Ensure that the device is always installed in such a

way that it is sufficiently cooled and cannot overheat.

2. Do not place ignition sources such as lighted candles near the device.

3. Vents must not be covered and fans must not be blocked.

4. Use the original packaging or packaging provided by the manufacturer for transport.

5. Avoid shock or impact to the device.

6. Observe the IP rating as well as the ambient conditions such as temperature and

humidity according to the specification.

7. Devices can always be further improved. In the event of any discrepancies between

the operating instructions and the device labelling with regard to operating condi-

tions, performance or other device characteristics, the information on the device

always takes precedence.

8. The device is not suitable for tropical climates and for operation at elevations

higher than 2000 m above sea level.

9. Unless explicitly stated, the unit is not suitable for operation in marine conditions.

PLEASE NOTE:

For conversion or retroﬁt sets or accessories provided by the manufacturer, it is

essential to observe the included instructions.

CAUTION! IMPORTANT INFORMATION REGARDING LIGHTING PRODUCTS!

1.Never look directly into the beam of light, not even for a short period of time.

2. Never look into the beam of light using optical devices such as a magnifying glass.

3. Stroboscopic effects may cause epileptic seizures in susceptible individuals!

4. Permanently installed lamps are built into these lighting units. These may not

be replaced by the user. In the event of a fault, please contact your distribution

partner.

SIGNAL TRANSMISSION BY RADIO

(E.G. W-DMX OR WIRELESS AUDIO SYSTEMS):

The quality and performance of wireless signal transmissions generally depends on

the ambient conditions.

For example, the following factors can impact range and signal quality:

Shielding (e.g. masonry, metal structures, water)

10

DMX

ITALIANO

POLSKI

ESPAÑOL

FRANCAIS

DEUTSCHENGLISH

High volumes of radio trafﬁc (e.g. powerful wireless LAN networks)

Interference

Electromagnetic radiation (e.g. LED video screens, dimmers)

All range speciﬁcations refer to free-ﬁeld line-of-sight applications without interfer-

ence!

The operation of radio transmission systems is subject to ofﬁcial regulations. These

may vary from region to region and must be checked by the operator before use (e.g.

radio frequency and transmission power).

WARNING: Devices with wireless signal transmission are not suitable for use in sen-

sitive areas in which radio operation can lead to potentially detrimental interactions.

These include e.g.:

• Hospitals, health centres or other healthcare facilities that provide patient treatment

with skilled personnel and equipment.

• Hazardous areas Class I, II and III

• Restricted areas

• Military facilities

• Aircraft or vehicles

• Areas where the use of mobile phones is prohibited

TRANSMISSION VIA W-DMX

WARNING: In general, wireless DMX transmission must not be used for applications

involving safety-related factors that might result in personal injury or property dama-

ge in the event of a failure.

This applies in particular to moving scene or truss structures, DMX-controlled motors/

lifts or lifting devices for operating DMX-operated platform lifts, hydraulic systems or

comparable moving components.

Furthermore, wireless DMX transmission must not be used to control flame or pyro-

technic devices, explosion-driven effects, or gas or liquid effects. These include e.g.

CO2 cannons, confetti shooters, water effects or similar.

NOTES ON PORTABLE OUTDOOR DEVICES

1. Temporary operation! Event equipment is generally only designed for temporary

operation.

2. Continuous operation or permanent structural installation – particularly outdoors –

can impair the function, surfaces and seals and cause premature material fatigue.

3. Damage to the surface coating can impair the device's corrosion protection. Da-

maged surface coating (e.g. scratches) must be promptly repaired using suitable

measures.

11

DMX DEUTSCHFRANCAIS

ESPAÑOL ENGLISH

ITALIANO POLSKI

PACKAGING CONTENT

Remove the product from the packaging and remove all packaging material.

Please check the completeness and integrity of the delivery and notify your distribution partner

immediately after purchase if the delivery is not complete or if it is damaged.

The packaging content includes:

X 1 x PIXBAR® Tunable White IP65 G2 LED BAR

X 2 x Sliding mounting feet with folding SPIN16® mounting spigot (pre-assembled)

X 1 x Standard frost filter

X 1 x Glare shield

X 1 x Power cable

X 1 x Operating instructions

INTRODUCTION

PIXBAR® TW G2 Outdoor LED BAR

CLPBTWIPG2 with 16 3-in-1 amber, warm white and cool white LEDs

CONTROL FUNCTIONS:

1-channel, 2-channel CCT, 3-channel Direct, 3-channel Strobe CCT, 5-channel Direct, 8-channel

Direct Control, 10-channel Effect Pattern, 11-channel Wash, 16-channel Pixel, 18-channel Pixel

CCT, 26-channel Pattern, 48-channel Pixel, 52-channel Pixel Dim, D2-channel Dim, D4-channel

CCT and D6-channel Direct DMX control

RDM

W-DMX™

Master/Slave modes

Stand-alone functions

FEATURES

• IP65 Protection class

• Convection cooling

• Operating voltage: 100 - 240 VAC

The LED Bar supports the RDM standard (Remote Device Management). Remote device manage-

ment allows the user to monitor the status and configuration of RDM devices using an RDM-ca-

pable controller, such as the optionally available Cameo UNICON (item number CLIREMOTE). The

Cameo UNICON also allows access to the entire fixture menu.

12

DMX

ITALIANO

POLSKI

ESPAÑOL

FRANCAIS

DEUTSCHENGLISH

CONNECTIONS, OPERATING AND DISPLAY ELEMENTS

1 2

3 4

5

6

7 8

1 POWER IN

IP65 mains input socket with rubber sealing cap (TRUE1 compatible). Operating voltage 100 - 240

VAC / 50 - 60 Hz. Use the supplied power cable (when not in use, always close the rubber sealing

cap).

2 POWER OUT

IP65 mains output socket with rubber sealing cap (TRUE1 compatible). Enables power supply to

other CAMEO lights. Ensure that the total current consumption of all connected devices does not

exceed the value specified on the device in amperes (A) (when not in use, always close the rubber

sealing cap).

3 DMX IN

Male IP65 5-pin XLR socket for connecting a DMX control device (e.g. DMX console; when not in

use, always close the rubber sealing cap).

4 DMX OUT

Female IP65 5-pin XLR socket for forwarding the DMX control signal (when not in use, always

close the rubber sealing cap).

5 OLED DISPLAY

The OLED display shows the currently activated operating mode or the current DMX address

(main screen), the menu items in the menu and the numerical value or operational status of

certain menu items.

6 TOUCH-SENSITIVE CONTROLS

MENU – Press MENU to access the main menu. Press again or repeatedly to return to the main

screen.

UP and DOWN – Select menu items in the main menu (DMX address, operating mode, etc.) and in

the sub-menus using UP and DOWN. Change value or status of a menu item, e.g. DMX address. To

change a value quickly (e.g. the DMX start address), press and hold UP or DOWN.

13

DMX DEUTSCHFRANCAIS

ESPAÑOL ENGLISH

ITALIANO POLSKI

ENTER – Press ENTER to access the menu level in order to make value or status changes, and to

access one of the sub-menus. Confirm value or status changes by pressing ENTER.

PLEASE NOTE:

• Before navigating the menu, make sure that the control panel is dry and clean so

that its functionality is not impaired.

• Moisture on the control panel can lead to incorrect operation of the fixture, e.g. in

outdoor conditions. Therefore, activate the lock function after configuring the light

to prevent incorrect operation due to moisture (Settings -> Display -> Autolock).

7 PRESSURE EQUALISATION ELEMENT

Pressure equalisation element to prevent condensation inside the housing. In order to ensure its

proper function, the element must be protected from dirt.

8 W-DMX™ ANTENNA

Antenna for W-DMX™ control.

ATTENTION: In order to provide protection from water sprays in accordance with the

IP65 protection class, the special DMX input and output sockets must be used with

special IP65-rated XLR connectors, or they must be sealed using the rubber caps.

When connected correctly, or when sealed correctly with the rubber sealing caps, the

POWER IN and POWER OUT sockets are protected from water sprays in accordance

with IP65.

14

DMX

ITALIANO

POLSKI

ESPAÑOL

FRANCAIS

DEUTSCHENGLISH

OPERATION

NOTES

• As soon as the fixture is correctly connected to the power supply, the following messages are

displayed in succession: “Update wait ...” (for service purposes only), “Welcome to Cameo”, the

model name and the software version. After this process, the light is ready for operation and

the previously activated operating mode is launched.

• If there is no input for approx. 30 seconds, the display automatically returns to the main screen.

• Note on the main screen in operating modes with external control: In the event that the control

signal is interrupted, the characters in the display begin flashing; once the control signal is

present again, the flashing stops.

• Briefly pressing UP from the main screen rotates the display by 180°.

SET DMX START ADDRESS (DMX address)

Starting from the main screen, press MENU to enter the main menu. Now use UP and DOWN to

select DMX Address and confirm with ENTER. Using the UP and DOWN buttons, configure the

desired DMX start address and press ENTER to confirm (the highest possible value depends on

the selected DMX mode).

CONFIGURE DMX MODE (DMX Mode)

Starting from the main screen, press MENU to enter the main menu. Now use UP and DOWN to

select DMX Mode and confirm with ENTER. Now select the desired DMX mode using UP and

DOWN and confirm the selection with ENTER. DMX modes with DMX delay channel and group

selection (Group 0 - 24) are marked with "D". DMX tables with the channel assignments can be

found in the DMX CONTROL section of this user manual.

15

DMX DEUTSCHFRANCAIS

ESPAÑOL ENGLISH

ITALIANO POLSKI

DMX modes with DMX delay channel

The DMX Delay function is a simple way to create a running light effect with a large number of

identical fixtures that are running the same software version, which would otherwise require a

suitable DMX controller and extensive programming. All the lights used (same model, same soft-

ware version) are set to the same DMX mode with DMX delay channel and controlled via the same

DMX start address.

Setting the DMX delay: Select one of the DMX modes with DMX delay channel and confirm the

selection (example: D4 CH CCT).

Assign the fixtures to one of up to 24 groups (plus Group 0) according to preference, whereby se-

veral lighs can be assigned to one group. The group number is also the factor by which the delay

time set in the DMX controller is multiplied. Confirm each entry by pressing ENTER.

The delay time of the DMX signal is set by means of a DMX controller in the separate DMX delay

channel of the corresponding DMX mode (0.0 s to 2.0 s in 0.1 s increments).

Setup example:

STAND-ALONE MENU MASTER / ALONE

In the stand-alone operating modes Direct LED, CCT and Play Loop, the control signal of the corre-

sponding mode can be output to slave units via XLR (DMX OUT) and W-DMX™:

Stand Alone -> Master/Alone -> Master

If you do not want to output the control signal, deactivate the output:

Stand Alone -> Master/Alone -> Alone

16

DMX

ITALIANO

POLSKI

ESPAÑOL

FRANCAIS

DEUTSCHENGLISH

In the stand-alone modes Auto Program and Play Loop, you can set a delay for slave units to delay

the output of the control signal.

Starting from the main screen, press MENU to enter the main menu. Now select Stand Alone,

confirm, select Master/Alone and confirm again.

This will take you to the submenu for configuring the submenu items (see table).

Control signal is forwarded via DMX OUT

Activate DMX control signal forwarding via W-DMX

Deactivate DMX control signal forwarding via W-DMX

Pair with ready-to-pair W-DMX devices

Disconnect all W-DMX connections

Set DMX delay for slave units: Off, 0.1s - 2.0s

Do not forward control signal

DIRECT LED STAND-ALONE MODE

The stand-alone mode “Direct LED” allows you to set the dimmer, amber, warm white and cold

white directly on the device, similar to a DMX control unit. This allows you to create a custom

scene without an additional DMX controller.

Starting from the main screen, press MENU to enter the main menu. Use UP and DOWN to select

Stand Alone, confirm with ENTER, then select Direct LED and confirm again with ENTER. Now

select the menu item you want to edit, confirm the selection, set the desired value and confirm

the entry.

CCT STAND-ALONE MODE (Correlated Colour Temperature)

The stand-alone mode “CCT” allows you to adjust the colour temperature in 100K increments

from 1800K to 6500K, as well as the hue (tint) and brightness (dimmer).

17

DMX DEUTSCHFRANCAIS

ESPAÑOL ENGLISH

ITALIANO POLSKI

Starting from the main screen, press MENU to enter the main menu. Use UP and DOWN to select

Stand Alone, confirm the selection, then select CCT and confirm again with ENTER. Now select

the menu item you want to edit, confirm the selection and make the settings as desired. Confirm

each entry.

PLAY LOOP STAND-ALONE MODE (8-step colour sequences 1 - 8)

The 8 available loops are pre-programmed at the factory, but can be customised in the Edit Loop

menu. The brightness can be set at a higher level.

Starting from the main screen, press MENU to enter the main menu. Using UP and DOWN, select

Stand Alone, confirm with ENTER, then select Play Loop and confirm again with ENTER. Now

select the menu item you want to edit, confirm the selection and make the settings as desired.

Confirm each entry.

TIMER FUNCTION

The timer function allows the Static stand-alone mode to be timer-controlled; the fade-in time can

be set from 0 to 60 minutes, the dwell time from 1 to 24 hours and the fade-out time from 0 to

60 minutes. After activation of the timer function, the timer control will take effect upon the next

start-up of the system.

Starting from the main screen, press MENU to enter the main menu. Select Stand Alone, confirm

the selection, then select Timer and confirm again. Under Timer, select the setting On and con-

firm. For custom timer settings, select Fade In, Dwell Time or Fade Out and confirm. You can

now adjust the respective value as desired. Confirm all entries. To deactivate the timer function,

select Timer->Off and confirm the entry.

Note: The timer function can be used in master/slave mode via cable and W-DMX™.

18

DMX

ITALIANO

POLSKI

ESPAÑOL

FRANCAIS

DEUTSCHENGLISH

EDIT LOOP

The brightness, step duration and fade time can be set independently for all eight loops. Starting

from the main screen, press MENU to enter the main menu. Using UP and DOWN, select Stand

Alone, confirm with ENTER, then select Edit Loop and confirm again. Now select the desired loop

for editing and confirm.

This will take you to the submenu for configuring the submenu items (see table). The settings for

each loop are made independently and are retained even after restarting the device.

Step selection

Set the step duration for the selected

step

Set the fade time for the selected

step

Selection of the colour temperature or

blackout for the selected step

Select colour temperature or blackout

or skip selected step

SLAVE MODE

Standard slave mode: Starting from the main screen, press MENU to enter the main menu.

Using the UP and DOWN buttons, select Slave, confirm with ENTER, then select Slave Group 0

and confirm again. Connect the slave and master units (same model, same software version)

using a DMX cable or via W-DMX™ and activate one of the stand-alone modes (Direct LED, CCT,

Play Loop) in the master unit. The slave unit will now follow the master unit.

Extended slave mode: If you wish to control the slave units in master/slave mode using one

of the Auto Program or Play Loop stand-alone modes, the control signal can be played back

with a time delay of up to 24 steps. The delay is set in the Stand Alone menu Master/Alone

in the master unit; the delay factor is set in the slave menu of the corresponding fixture (Group).

This is a simple way to create a running light effect with a large number of identical lighs that are

running the same software version, which would otherwise require a suitable DMX controller and

19

DMX DEUTSCHFRANCAIS

ESPAÑOL ENGLISH

ITALIANO POLSKI

extensive programming. Connect the slave and master units (same model, same software version)

using a DMX cable or via W-DMX™.

0 - 24 Set slave group for signal delay

XLR (permanently active)

Activate W-DMX module

Deactivate W-DMX module

Disconnect all connections

and place in pairing standby

mode

Assign the fixtures to one of up to 24 groups (plus Group 0) according to preference, whereby se-

veral lights can be assigned to one group. The group number is also the factor by which the delay

time set in the master unit is multiplied.

Setup example:

SYSTEM SETTINGS (Settings)

Starting from the main screen, press MENU to enter the main menu. Using the UP and DOWN

buttons, select Settings and confirm with ENTER.

This will take you to the submenu for editing the following submenu items (see table, select with

UP and DOWN, confirm with ENTER, change value or status with UP and DOWN, confirm with

ENTER).

=Wireless

settings

W-DMX activated

W-DMX deactivated

W-DMX mode: Receiver

G3 (G3 transmission standard)

G4s (G4s transmission standard)

Unpair all devices and make them ready

for pairing

20

DMX

ITALIANO

POLSKI

ESPAÑOL

FRANCAIS

DEUTSCHENGLISH

=Wireless

settings

Pair with W-DMX devices. W-DMX must

be enabled on all devices, and the

pairing with a transmitter must be reset

(Receive Reset).

Send incoming signal to XLR connector

Use the XLR input signal in case the

W-DMX signal is lost.

No connection between W-DMX signal

and XLR connectors

=Display

settings

Rotate display by 180° (e.g. for overhead

installation)

No display rotation

Display illumination permanently on

Deactivate display illumination after

approx. 20 seconds of inactivity

Function disabled

The controls and display are locked

after approx. 60 seconds without any

operation. Unlock: Press UP and DOWN

simultaneously for approx. 5 seconds

=

Dimming

behaviour

and PWM

frequency

Dimmer curve: The light intensity in-

creases linearly with the DMX value

Dimmer curve: The light intensity can be

adjusted ﬁnely in the lower DMX value

range and coarsely in the upper DMX

value range

Dimmer curve: The light intensity can be

adjusted coarsely in the lower DMX value

range and ﬁnely in the upper DMX value

range

Light intensity can be adjusted ﬁnely

at lower and higher DMX values and

coarsely at medium DMX values

Select LED PWM frequency

The light responds abruptly to changes

in DMX value

The ﬁxture behaves like a halogen light

with smooth brightness changes

La page charge ...

Cameo PIXBAR® TW IP G2 Manuel utilisateur

Cameo PIXBAR® TW IP G2 Manuel utilisateur

dans d''autres langues

Documents connexes