PowerSmart DB5021LED Manuel utilisateur

INSTRUCTION MANUAL

EN 21"ELECTRIC SNOW THROWER

FR 21"CHASSE-NEIGE ÉLECTRIQUE

ES LANZDE NIEVE ELECTRICA DE 21"

Model

Have product questions or need technical support? Please feel free to contact us!

Website:

www.PowerSmartUSA.com

Toll free: 1-800-791-9458 Mon-Fri 9-5 EST

Email: support@amerisuninc.com

# DB5021LED

Website

2

3

TABLE OF CONTENTS

Feature Identification ...................................................................................... 4

Safety Information ........................................................................................... 5

Operating Instructions ..................................................................................... 7

Troubleshooting .............................................................................................. 12

Care and Maintenance ..................................................................................... 12

Exploded View and Part List ........................................................................... 13

Two Years Limited Warranty .......................................................................... 17

PRODUCTS SPECIFICATIONS

Voltage:120v,60Hz

Input Power:15Amp

Rotation speed:2,100 RPM

Clearing width and depth: Approx. 53 cm x 31 cm (21 in. x 12.5 in.)

Max. throwing distance: 10 m (30 ft.)

Net Wight:18 kg (40lbs)

EN

4

FEATURE IDENTIFICATION

1

Auger Control

7

Auger

2

Switch button

8

Chute Deflector

3

Upper Tube

9

Chute

4

Polarized Plug

10

Chute Crank

5

Lower Tube

11

Knob

6

Wheel

12

Light

5

SAFETY INFORMATION

Please read and understand this entire manual before attempting to assemble, operate or install the product.

Work Area

 Keep work area clean and well-lit. Cluttered, dark areas invite accidents.

 Do not operate snow thrower in an explosive atmosphere, such as in the presence of flammable liquids, gases,

or dust. Electrical appliances create sparks that may ignite the dust or fumes.

 Keep children, pets, and bystanders away from work area. Be aware that the normal noise of the machine when

turned on may make it difficult for you to hear approaching people.

Electrical Safety

 Electrical plugs must match the outlet. Never modify the plug in any way. Do not use any adaptor plugs with

grounded appliances. Unmodified plugs and matching outlets will reduce risk of electric shock.

 Avoid body contact with earthed or grounded surfaces such as pipes, radiators, ranges, and refrigerators. There

is an increased risk of electric shock if your body is earthed or grounded.

 Do not abuse the cord. Keep cord away from heat, oil, sharp edges or moving parts. Damaged or yank the cord

to disconnect it from the electrical outlet.

 Replace or properly repair damaged cords. If cord is damaged in any manner while plugged in, pull the

extension cord from the wall receptacle.

 Contact with water while operating the snow thrower can result in electric shock and serious bodily injury. Do

not use the snow thrower in damp or wet locations or expose to rain. Do not handle the plug or the appliance

with wet hands or while standing in water.

 Extension Cord-WARNING –Only use a UL-rated extension cord for OUTDOOR, all-weather use (usually

orange color).The extension cord MUST be of the proper gauge size depending on it’s length(see page 11).To

prevent the extension cord from disconnecting during operation.tie it around top right side of the middle frame

before connecting it to the snow thrower as shown in Figure 2 on page 12.

 Turn off the power switch and disconnect the power cable before inspecting, servicing, repairing, or cleaning

the snow thrower stop completely.

 Do not move or transport the snow thrower when the plug is connected to the power socket and the switch in

turned on.

Personal Safety

 Stay alert-watch what you are doing and use common sense when operating the snow thrower.

 Do not use the machine when tired, ill, or under the influence of drugs, alcohol, or medication. A moment of

inattention may result in serious personal injury.

 Wear proper clothing-Wearing rubber boots offers additional protection from electric shock. Do not wear loose

clothing or jewelry that may become caught in the machine. Wear protective headgear to keep hair away from

revolving parts of the machine. Safety glasses offer better protection than everyday eyeglasses.

 Moving parts present risks –Keep your face, hair, clothing, hands, and feet away from moving parts. All guards

and safety attachments must be installed properly before using the unit. Shut off and disconnect cord before

touching any parts other than handles and switch.

 Surfaces-This snow thrower is intended for use on paved surfaces. Do not use on gravel, stone, or other

unpaved surfaces unless the snow thrower is adjusted for such surfaces according to the instructions given in

the operators manual.

 Avoid accidental starting –Make sure the switch is in the off position before plugging in the unit. Do not carry

the snow thrower with your finger on the switch.

6

 Body position-Maintain proper footing and balance at all times. Place heels firmly on the ground and tightly

grasp the handle bar. Watch for uneven surfaces and do not over reach. In case you fall or collide with the snow

thrower, inspect the unit for damage. When steeping backwards, be careful to avoid obstacles beneath your feet

or behind you to avoid falling.

 Snow Thrower Use and Care

 Know your snow blower-Familiarize yourself with the main parts of your snow thrower. Read the operators

manual carefully. Learn your snow throwers applications and limitations as well as specific potential hazards

related to this machine. Do not use this machine for any purpose other than one for which it was designed.

Otherwise, it may cause mechanical defaults, serious damage or personal injury.

 Preliminary unit inspection –Thoroughly inspect the unit before use. Make sure all the parts are secure and

installed correctly. If you notice any abnormalities, do not use the machine until it has been properly repaired.

Always perform a test run the first time you use the snow thrower or after replacing parts to ensure that unit is

functioning properly.

 Preliminary area inspection-Clear the area to be plowed before each use. Remove all objects such as rocks,

broken glass, nails, wire, or string which can be thrown by or become entangled in the snow thrower .Keep the

area of operation clear of other people and pets.

 Excessive force –The snow thrower was designed to respond at a certain rate for various snow conditions for

optimum safety band performance. Do not force it; keep pressure constant.

 Malfunctioning switch-Do not use the snow blower if the switch does not turn it on and off. Any electrical

appliance that can not be controlled by the switch is not safe to use and must be repaired.

 Hitting an object-If the snow thrower accidentally strikes an object, stop the snow thrower. Inspect for damage;

repair or replace any damaged part before restarting and operating the snow thrower.

 Discharge chute safety -Never direct the snow discharge chute at the operator, at bystanders, at vehicles or at

windows. Thrown snow and foreign objects accidentally picked up by the snow thrower can cause serious

damage and personal injury. Do not use your hands to unclog the discharge chute. Stop the motor before

removing debris.

 Abnormal operation-If you notice the snow thrower running in an unstable state or hear abnormal sounds from

machine，stop the machine, disconnect the power immediately, and contact your original distributor.

 Noise control-When using the snow thrower, you must respect local laws and regulations regarding noise

control and environmental protection. To avoid noise disturbance, you should carefully decide upon an

appropriate operation time and consider the surrounding conditions.

 When work is completed -Disconnected the snow thrower from the power source when not in use, when

changing accessories, and before performing any maintenance.

 Store safety-Store snow thrower indoors in a dry area between uses. Keep in a locked area where children and

unauthorized users can not gain access. Do not store the machine while it is still connected to the power source.

It may cause damage and injury.

 Maintain for safety and longevity-Check for misalignment or binding of moving parts, breakage of parts, and

any other conditions that may affect the units operation. If damaged, repair or replace the damaged part before

use. Use only those replacement parts made for your model. When replacing any parts, you must strictly

observe the instructions and procedures described in this manual. Special care should be paid to any rubber

parts, since these parts may increase the engine load and decrease its mechanical power if damaged.

7

PRODUCT LABELS

WARNING-Read, understand and follow all safety labels and markings on the unit.

CAUTION

Inspect wiring, which, if damaged during shipping, may cause serious bodily injury during equipment use. If any

damage is seen or suspected, do not assemble. instead, contact our customer service department at 1-800-791-9458.

Handle with care during assembly so that electrical wiring does not become damaged.

OPERATING INSTRUCTIONS

Note: Before using this machine, make sure that the power source you will use complies with the

specification’sdetailedinthismanual.Beforeinsertingtheplugintothesocket, verify that the snow throwers auger and

scraper are firmly attached with screws. Perform a test run to ensure that the rotor turns freely.

SECURING THE EXTENSION CORD

1. For safe and efficient use of your snow thrower, use only a UL-rated extension cord recommended for outdoor

use. Refer to the Extension Cord Chart below.

WARNING

Electric shock may cause SEVERE INJURY or DEATH. Heed these warnings:

• Do not allow any part of snow thrower to make contact with water while powered on. If the appliance becomes

wet while turned off, wipe dry before starting.

8

• Use only a UL-rated extension cord for outdoor, all-weather use. Do not use an extension cord more

than150feet long.

• Don't touch the appliance or its plug with wet hands or while standing in water. Wearing rubber boots offers

some protection.

EXTENTION CORD CHART

Cord Length

Up to 100 ft.

100-150ft.

Wire Gauge

14

12

2. To prevent the extension cord from disconnecting during use, tie the female end of

the extension cord in to a loose knot on the top right side of the middle frame (B)

before connecting to the male plug in the socket of the snow thrower.

Note: The protective cover around the polarized plug is compatible with most extension

cords. When choosing an extension cord be sure the female end of your cord will fit

into the polarized plug.

3. Note that the snow thrower has a polarized male plug (O), with one prong in the

socket slightly longer and wider than the other. The extension cord female end

should be likewise polarized, so that the extension cord fits snugly into the socket.

WARNING

Damaged electrical cords present risk of fire, electric shock, and serious bodily injury.

Before operating the snow thrower, carefully examine the electrical cord. Id the cord is damaged, do not use the

snow thrower. Replace or repair the damaged cord immediately. If you need assistance, contact our customer

service department at 1-800-791-9458.

POWERING ON AND OFF

1. Connect extension cord to the male plug on the snow thrower then connect

extension cord to proper AC power source.

2. Press and Hold the switch button.

9

3. To start, while holding the switch button in, pull the handlebar toward you until it

touches the handle. The switch button must be pressed in and held before pulling the

handle. Once the snow thrower starts, release the switch button.

4. To stop, release switch button.

USING LIGHT

1. Press button 1 to control the light. Press 1 time for high light, 2 times for low light,

and 3 times for flash. Press 4 times to turn off the light.

2. 2 is the charging port, The light switch displays red when charging and green

when fully charged.

MOVING THE MACHINE AND PLOWING THE SNOW

WARNING

Foreign objects, such as rocks, broken glass, nails, wire, or string, can be picked up and thrown by the snow

thrower, causing serious personal injury.

Remove all foreign objects from the area to be plowed before operating the snow thrower.

 Keep the area of operation free of foreign objects that can be become thrown by the rotor blades.

 Perform a thorough inspection of the area since some objects may be hidden from view by surrounding

snow, If the snow thrower hits an obstruction or picks up a foreign object during use, stop the snow

thrower, disconnect the extension cord, remove the obstruction, and inspect the unit for damage.

Repair or replace any damaged parts before restarting and operating the unit.

 Keep children, pets, and bystanders away from the area of operation. Be aware that the normal noise of the

machine when turned on may make it difficult for you to hear approaching people.

 When moving the snow thrower, use the wheels on the sides as the pivot point. Slightly tilt the snow

thrower on this pivot point to move it forward or backward.

 Start your clearing path near the electrical outlet and work outward, throwing snow in a back and forth

motion, To clear in the opposite direction, stop over the cord and pivot the snow thrower on its wheels.

Make sure to overlap clearing paths.

 Note wind direction. If possible, move in the same direction as the wind so that the snow is not thrown

against the wind (and thus back into your face and back onto the patch).

 While moving the snow thrower, do not drag the power cable violently or roughly. The snow thrower

should move within the range that the cable can reach.

 Do not push the snow thrower with excessive force. You should push machine gently and evenly in

accordance with the units throw rate.

 Some parts of the snow thrower may freeze under extreme temperature conditions. Do not attempt to

operate the snow thrower with frozen parts. If the parts freeze while the snow thrower is in use, stop the

snow thrower, unplug the extension cord, and inspect for frozen parts. Free all parts before operating the

snow thrower. Never force controls that have frozen.

10

 Working on pebbles, gravel, or unpaved surfaces-To avoid throwing loose surface material along with the

snow, push down on the raise the scrapper at the base of the unit above the pebbles or gravel.

CHANGING THROW DIRECTION AND THROW HEIGHT

WARNING

Never direct the snow discharge chute at the operator, at bystanders, at vehicles or at nearby windows.

Discharge snow and foreign objects accidentally picked up by the snow thrower can cause serious damage and

personal injury.

Always orient the discharge chute in the opposite direction from where you, bystanders, surrounding vehicles,

or windows are located.

1. The discharge chute (H) can be adjusted 180 degrees

by rotating the chute crank. Rotate the chute control

crank clockwise to move the discharge chute (H) to

the left, counterclockwise to move the chute to the

right.

2. The chute deflector on the top of the discharge chute (H) controls the height of the snow stream. Loosen

both chute deflector knobs to raise or lower the deflector to the desired height you wish to throw the snow.

Tighten the knobs to secure the deflector.

Note: Do not over tighten the chute deflector knobs.

H

11

DRIVE BELT REPLACEMENT

WARNING Entanglement Hazard - Before performing any service procedures, make sure the snow thrower is

disconnected from the power source.

Note: Record component position before disassembly, to assist in reassembly.

1. Using screw driver, remove 3 screws attaching belt cover to housing.

2. Manually push the belt tension pulley up to reduce belt tension.

Note: When replacing the belt it is important to determine the cause of the failure (if applicable) and take

corrective action to avoid repeated failure.

3. Inspect the old belt, pulleys and tension spring before installing a new belt for damage and wear, replace

parts as required

4. Inspect the new belt to ensure it is the correct size and type.

Original – Part Number: 3PK695

5. Manuallypushthebelttensionpulleyuptoallowinstallationofthenewbelt.

6. Position the belt onto the small drive pulley, then while holding the belt tension pulley away from the belt,

carefully wind the belt onto the large pulley. Do not damage the new belt during installation.

7. Using screwdriver, install 3 screws attaching belt cover to housing.

12

TROUBLESHOOTING

Problem

Possible Causes

Remedy

WARNING - Before attempting to make any inspections, repairs or adjustments, stop the snow thrower, wait for

all moving parts to stop moving and carefully disconnect the AC extension cord from the power source.

No start

condition,

won't not

turn on

No power from AC

power source

Connect to known good AC power source

Extension cord not

connected

Securely connect extension cord at power source and

snow thrower

Extension cord faulty

Connect a known good extension cord

Improper starting

procedure

Review "Powering ON and OFF" procedure in this

manual

Auger damaged or

blocked

Check auger for damage, blockage or frozen

condition, repair as required

Faulty switch, wiring or

motor

Call customer service or contact service center

Turns on,

but won't

blow snow

Auger damaged or

blocked

Check auger for damage, blockage or frozen

condition, repair as required

Chute blocked or

damaged

Check chute for damage or blockage, repair as

required

Drive belt damaged

or loose

Check drive belt condition, repair as required (drive

belt is located on left side behind cover)

Turns on,

but won't

run at full

speed

Extension cord faulty

Connect a known good extension cord

Improper extension

cord

Check extension cord length and gauge for use in proper

application, Review "Extension Cord Chart" in this manual

Auger damaged or

blocked

Check auger for damage, blockage or frozen

condition, repair as required

Drive belt damaged or

loose

Check drive belt condition, repair as required (drive

belt is located on left side behind cover)

Faulty wiring or motor

Call customer service or contact service center

CARE AND MAINTENANCE

WARNING

Make sure to turn off the switch and disconnect the extension cord before performing any maintenance task on

your snow thrower.

 Run the snow thrower for a few minutes to melt away any snow on the snow thrower. Turn the snow

thrower's power off.

 Disconnect the extension cord from the snow thrower.

 Examine the extension cord thoroughly for signs of wear or damage. Replace it if it is worn or damaged.

 Examine the snow thrower thoroughly for worn, loose bolts or damaged parts. For repairing or replacing

parts, contact customer service.

 Store the extension cord with the snow thrower.

 Store the unit in a locked and dry or high and dry place to prevent unauthorized use/damage and keep out

of the reach of children. Store the instruction manual along with unit for future use.

13

EXPLODED VIEW AND PART LIST

AUGER HOUSING ASSEMBLY

14

ITEM

SKU#

DESCRIPTION

QTY

ITEM

SKU#

DESCRIPTION

QTY

1

303020561

hex bolt M6*16

6

43

301080009

overcurrent protector

1

2

303050066

shaft ring Φ17

1

44

306010037

screw crimping cap

1

3

303100034

6203Z ball bearing

2

45

303010203

screw 3*10

4

303070797

bearing platen welded

2

46

303070074

brush holder

2

5

303020106

hex bolt M8*20

12

47

301110043

brush cover

2

6

303042013

flat washer

12

48

301110058

electrical carbon

2

7

303030036

lock nut M8

12

49

301110044

brush component

2

8

302110091

short scraper

2

50

303010162

screw ST4×70

2

9

302110092

long scraper

4

51

303041008

spring washer

2

10

303181282

auger shaft welded

1

52

303042038

flat wahser

2

11

303042018

flat washer Φ18*Φ24*2

3

53

203020050

rear motor support

1

12

203010646

belt pulley

1

54

303100023

608Z ball bearing

1

13

303042009

flat wahser

1

55

301030008

stator

1

14

303041009

spring washer φ6

1

56

203050587

motor holder

1

15

303020282

hex bolt

1

57

303010185

screw ST6.3*30

4

16

303010176

screw ST6.3×16

2

58

203020063

front motor bracket

1

17

303010383

screw ST4.8*10

1

59

301030005A

rotor

1

18

203050655

right side cover

1

60

303100030

6001Z ball bearing

1

19

203010747

LOGO plate

1

61

303090005

middle cover

1

20

203050170A

base

1

62

303110021

woodruff key

1

21

303070739

right corner

1

63

203060019

small gear

1

22

303010284

screw ST4.8×12

4

64

303030047

nut M8-

1

23

303010108

screw ST4.8*16

3

65

303130019

tensioner spring

1

24

303070741A

Shovel

1

66

303042019

flat wahser

1

25

303070738

left corner

1

67

303020077

bolt M4*10

1

26

302040090

belt 3PK695

1

54

303100023

608Z ball bearing

1

27

203050654

left side cover

1

68

303050029

shaft ring

1

17

303010383

screw ST4.8*10

1

69

303160004

big gear

1

16

303010176

screw ST6.3×16

2

70

303110020

woodruff key

1

28

303030066

normal nut

2

71

303160111

output shaft

1

29

203020336A

knob

2

72

303100024

6201Z ball bearing

1

30

303042023

flat wahser

2

73

303070029

oil pad

1

31

203020380

tooth pad M8*25

2

74

303090002

end cover

1

32

303020161

bolt

4

75

303010221

screw ST4×40

2

33

203050174

upper chute

1

51

303041008

spring washer

3

34

203050175

middle chute

1

52

303042038

flat wahser

3

35

303030077

lock nut M8

2

76

303020079

bolt M4*14

3

36

203010648

chute handle

1

77

303180588

tensioning wheel bracket

welding

1

37

203050172

rotating disc

1

66

303042019

flat wahser

3

38

203010647

located block

1

67

303020077

bolt M4*10

3

39

303130138

chute pressure spring

2

78

203020077

tension wheel

1

40

203050171

base part

1

79

303100016

6000RS ball bearing

1

41

203050567

motor bracket

1

80

303042035

flat washer

1

42

303010358

screw ST4.2×14

2

67

303020077

bolt M4*10

1

16

303010176

screw ST6.3×16

8

81

303160957

small pulley

1

23

303010108

screw ST4.8*16

6

15

PANEL ASSEMBLY

16

ITEM

SKU#

DESCRIPTION

QTY

ITEM

SKU#

DESCRIPTION

QTY

82

303071480

right support

plate

1

29

203020336A

knob

4

83

303010353

screw ST6.3x16

8

28

303030066

normal nut

4

84

303071479

left support

plate

1

105

303081213

middle handle

1

85

303160845

butterfly pin

2

106

303081212

upper handle

1

86

303181283A

shaft

1

107

301120014

light

1

87

203021421

right wheel

cover

1

108

301040045

power cord

1

88

303121002

cotter pin

2

109

303010028

screw 4*18

10

89

303100065

wheel bearing

4

110

302070001

sealing ring

4

90

203050544

8 inch wheel

2

111

203050660

lower switch box

1

91

203050658

left wheel cover

1

112

303130013

knob spring

1

92

203050662

battery pack

cover

1

113

303042019

flat wahser

1

93

303100086

cover shaft

2

114

303010313

screw 4×12

1

16

303010176

screw ST6.3×16

2

115

203021102A

switch button

1

94

203050656

upper cover

1

116

203010655

push rod

1

95

303042019

flat wahser

1

117

203021101A

right switch trigger

2

96

303010363

screw ST4.2*10

1

118

203050552

upper switch box

1

97

203020047

cable clamp

1

114

303010313

screw 4×12

2

16

303010176

screw ST6.3×16

4

119

303130125

anti-self-locking button spring

1

98

203050657

bottom cover

1

120

203010656

anti-self-lock button

1

99

303020124

hex bolt

7

121

303130124

spring

1

100

303042013

flat wahser

6

122

301040078A

connection line

1

101

303030077

lock nut M8

7

123

203050519

wire clip

2

102

303081214

lower handle

1

97

203020047

cable clamp

2

103

303020057

T-screw M8×45

4

124

301100046

switch

1

104

303043010

concave pad

4

17

TWO (2) YEARS LIMITED WARRANTY

POWERSMART IS COMMITTED TO BUILDING TOOLS THAT ARE DEPENDABLE FOR YEARS. OUR

WARRANTIES ARE CONSISTENT WITH OUR COMMITMENT AND DEDICATION TO QUALITY.

TWO (2) YEARS LIMITED WARRANTY OF POWER SMART PRODUCTS FOR HOME USE.

POWERSMART (“SELLER") WARRANTS TO THE ORIGINAL PURCHASER ONLY, THAT ALL POWERSMART

CONSUMER POWER TOOLS WILL BE FREE FROM DEFECTS IN MATERIAL OR WORKMANSHIP FOR A

PERIOD OF TWO (2) YEARS FROM DATE OF PURCHASE. NINETY (90) DAYS FOR ALL POWERSMART

PRODUCTS, IF THE TOOL IS USED FOR PROFESSIONAL OR COMMERCIAL USE.

SELLER’S SOLE OBLIGATION AND YOUR EXCLUSIVE REMEDY UNDER THIS TWO (2) YEARS LIMITED

WARRANTY AND, TO THE EXTENT PERMITTED BY LAW, ANY WARRANTY OR CONDITION IMPLIED BY LAW,

SHALL BE THE REPAIR OR REPLACEMENT OF PARTS, WITHOUT CHARGE, WHICH ARE DEFECTIVE IN

MATERIAL OR WORKMANSHIP AND WHICH HAVE NOT BEEN MISUSED, CARELESSLY HANDLED, OR

MISREPAIRED BY PERSONS OTHER THAN SELLER OR AUTHORIZED SERVICE CENTER. TO MAKE A

CLAIM UNDER THIS LIMITED WARRANTY, YOU MUST RETURN THE ENTIRE POWER TOOL PRODUCT;

TRANSPORTATION PREPAID, TO POWERSMART INCLUDE A LEGIBLE COPY OF THE ORIGINAL RECEIPT,

WHICH LISTS THE DATE OF PURCHASE (MONTH AND YEAR) AND THE NAME OF THE COMPANY

PURCHASED FROM.

THIS LIMITED WARRANTY DOES NOT APPLY TO ANY ACCESSORY ITEMS INCLUDED WITH THE TOOL

SUCH AS CIRCULAR SAW BLADES OTHER RELATED ITEMS OR TO ANY REPLACEMENT PARTS LISTED

UNDER MAINTENANCE.

ANY IMPLIED WARRANTIES SHALL BE LIMITED IN DURATION TO TWO (2) YEARS FROM DATE OF

PURCHASE. SOME STATES IN THE U.S. AND SOME CANADIAN PROVINCES DO NOT ALLOW LIMITATIONS

ON HOW LONG AN IMPLIED WARRANTY LASTS, SO THE ABOVE LIMITATION MAY NOT APPLY TO YOU.

IN NO EVENT SHALL SELLER BE LIABLE FOR ANY INCIDENTAL OR CONSEQUENTIAL DAMAGES

(INCLUDING BUT NOT LIMITED TO LIABILITY FOR LOSS OF PROFITS) ARISING FROM THE SALE OR USE

OF THIS PRODUCT. SOME STATES IN THE U.S. AND SOME CANADIAN PROVINCES DO NOT ALLOW THE

EXCLUSION OR LIMITATION OF INCIDENTAL OR CONSEQUENTIAL DAMAGES, SO THE ABOVE

LIMITATION OR EXCLUSION MAY NOT APPLY TO YOU.

THIS LIMITED WARRANTY GIVES YOU SPECIFIC LEGAL RIGHTS, AND YOU MAY ALSO HAVE OTHER

RIGHTS WHICH VARY FROM STATE TO STATE IN THE U.S., PROVINCE TO PROVINCE IN CANADA AND

FROM COUNTRY TO COUNTRY.

FOR QUESTIONS / COMMENTS, TECHNICAL ASSISTANCE OR REPAIR PARTS – PLEASE CALL TOLL FREE

AT: 1-800-791-9458 (M-F 9AM – 5PM EST) EMAIL: SUPPORT@AMERISUNINC.COM

SAVE YOUR RECEIPTS. THIS WARRANTY IS VOID WITHOUT THEM.

18

TABLE DE MATIÈRES

IDENTIFICATION DES CARACTÉRISTIQUES ....................................................................................................................... 19

INFORMATIONS SUR LA SÉCURITÉ

................................................................................................................................... 20

INSTRUCTIONS D'UTILISATION

.......................................................................................................................................... 22

DÉPANNAGE

............................................................................................................................................................................. 27

ENTRETIEN ET MAINTENANCE

.......................................................................................................................................... 27

VUE EXPLOSÉE ET LISTE DES PIÈCES .................................................................................................................................. 28

GARANTIE LIMITÉE DE DEUX (2) ANS ................................................................................................................................. 32

SPÉCIFICATIONS DES PRODUITS

Tension :120v,60Hz

Puissance d'entrée :15Amp

Vitesse de rotation :2,100 RPM

Largeur et profondeur du défrichement : Environ 53 cm x 31 cm (21 pouces x 12.5 pouces)

Distance de projection max. : 10 m (30 pieds)

Poids net :18 kg (40 livres)

FR

19

IDENTIFICATION DES CARACTÉRISTIQUES

1

Contrôle de la tarière

7

Tarière

2

Bouton de commutation

8

Déflecteur de goulotte

3

Tube supérieur

9

Goulotte

4

Fiche polarisée

10

Manivelle de la goulotte

5

Tube inférieur

11

Bouton

6

Roue

12

Lumière

20

INFORMATIONS SUR LA SÉCURITÉ

Veuillez lire et comprendre l'ensemble de ce manuel avant d'essayer d'assembler, d'utiliser ou d'installer le

produit.

Espace de travail

 Gardez la zone de travail propre et bien éclairée. Les zones encombrées et sombres sont propices aux accidents.

 Ne faites pas fonctionner la souffleuse à neige dans une atmosphère explosive, par exemple en présence de

liquides, de gaz ou de poussières inflammables. Les appareils électriques créent des étincelles qui peuvent

enflammer la poussière ou les fumées.

 Tenez les enfants, les animaux domestiques et les passants à l'écart de la zone de travail. Sachez que le bruit

normal de l'appareil lorsqu'il est allumé peut vous rendre difficile d'entendre les personnes qui s'approchent.

Sécurité électrique

 Les fiches électriques doivent correspondre à la prise de courant. Ne modifiez jamais la fiche de quelque

manière que ce soit. N'utilisez pas de fiches adaptatrices avec des appareils mis à la terre. Les fiches non

modifiées et les prises assorties réduisent le risque de choc électrique.

 Évitez tout contact du corps avec des surfaces mises à la terre ou à la masse, telles que les tuyaux, les radiateurs,

les cuisinières et les réfrigérateurs. Le risque de décharge électrique est plus élevé si votre corps est mis à la

terre ou à la masse.

 N'abusez pas du cordon d'alimentation. Tenez le cordon à l'écart de la chaleur, de l'huile, des arêtes vives ou

des pièces mobiles. Si le cordon est endommagé ou si vous tirez dessus, débranchez-le de la prise électrique.

 Remplacez ou réparez correctement les cordons endommagés. Si le cordon est endommagé de quelque manière

que ce soit lorsqu'il est branché, tirez la rallonge de la prise murale.

 Le contact avec l'eau pendant le fonctionnement de la souffleuse peut entraîner une décharge électrique et des

blessures corporelles graves. N'utilisez pas la souffleuse dans des endroits humides ou mouillés et ne l'exposez

pas à la pluie. Ne manipulez pas la prise ou l'appareil avec des mains mouillées ou en restant debout dans l'eau.

 Rallonge électrique AVERTISSEMENT - Utilisez uniquement une rallonge électrique homologuée UL pour

une utilisation en EXTERIEUR, par tous les temps (généralement de couleur orange). La rallonge électrique

DOIT être de la bonne taille en fonction de sa longueur (voir page 31). Pour éviter que la rallonge électrique ne

se débranche pendant le fonctionnement, attachez-la autour du côté supérieur droit du châssis central avant de

la brancher à la souffleuse, comme indiqué dans la figure 2 de la page 32.

 Eteignez l'interrupteur et débranchez le câble d'alimentation avant d'inspecter, d'entretenir, de réparer ou de

nettoyer complètement l'arrêt de la souffleuse à neige.

 Ne déplacez pas ou ne transportez pas la souffleuse à neige lorsque la fiche est branchée sur la prise de courant

et que l'interrupteur est en position marche.

Sécurité personnelle

 Restez vigilant, surveillez ce que vous faites et faites preuve de bon sens lorsque vous utilisez la souffleuse.

 N'utilisez pas la machine lorsque vous êtes fatigué, malade ou sous l'influence de drogues, d'alcool ou de

médicaments. Un moment d'inattention peut entraîner des blessures graves.

 Portez des vêtements appropriés - Le port de bottes en caoutchouc offre une protection supplémentaire contre

les décharges électriques. Ne portez pas de vêtements amples ou de bijoux qui pourraient se prendre dans

l'appareil. Portez un casque de protection pour éloigner les cheveux des pièces tournantes de la machine. Les

lunettes de sécurité offrent une meilleure protection que les lunettes de tous les jours.

 Les pièces mobiles présentent des risques - Gardez votre visage, vos cheveux, vos vêtements, vos mains et vos

pieds loin des pièces mobiles. Tous les dispositifs de protection et les accessoires de sécurité doivent être

correctement installés avant d'utiliser l'appareil. Éteignez et débranchez le cordon avant de toucher toute pièce

autre que les poignées et l'interrupteur.

 Surfaces - Cette souffleuse à neige est destinée à être utilisée sur des surfaces pavées. Ne l'utilisez pas sur du

gravier, de la pierre ou d'autres surfaces non pavées, à moins que la souffleuse ne soit réglée pour ces surfaces

conformément aux instructions données dans le manuel d'utilisation.

La page charge ...

PowerSmart DB5021LED Manuel utilisateur

PowerSmart DB5021LED Manuel utilisateur

dans d''autres langues

Documents connexes

Autres documents