Pioneer DEH-X2900UI Manuel utilisateur

English Français Italiano Español Deutsch Nederlands Русский

CD RDS RECEIVER

AUTORADIO CD RDS

SINTOLETTORE CD RDS

REPRODUCTOR DE CD CON RECEPTOR RDS

CD RDS-EMPFÄNGER

CD RDS-ONTVANGER

CD RDS ПРИЕМНИК

DEH-X2900UI

Owner’s Manual

Mode d’emploi

Manuale d’istruzioni

Manual de instrucciones

Bedienungsanleitung

Handleiding

Руководство пользователя

2En

Before You Start....................................................................................... 2

Getting Started........................................................................................ 3

Radio.......................................................................................................... 4

CD/USB/iPod/AUX................................................................................... 5

App Mode................................................................................................. 7

Spotify®..................................................................................................... 7

Using Pioneer ARC APP.......................................................................... 8

Settings ..................................................................................................... 9

FUNCTION settings ................................................................................. 9

AUDIO settings...................................................................................... 10

SYSTEM settings ................................................................................... 10

ILLUMINATION settings....................................................................... 11

MIXTRAX settings................................................................................. 12

Connections/Installation ..................................................................... 12

Additional Information ........................................................................ 14

About this manual:

• In the following instructions, a USB memory or USB audio player are referred to as

“USB device”.

• In this manual, iPod and iPhone are referred to as “iPod”.

Table of Contents

Thank you for purchasing this PIONEER product

To ensure proper use, please read through this manual before using this product. It is especially

important that you read and observe WARNINGs and CAUTIONs in this manual. Please keep the

manual in a safe and accessible place for future reference.

Private households in the member states of the EU, in Switzerland and Norway may return their used

electronic products free of charge to designated collection facilities or to a retailer (if you purchase a

similar new one).

For countries not mentioned above, please contact your local authorities for the correct method of

disposal.

By doing so you will ensure that your disposed product undergoes the necessary treatment, recovery

and recycling and thus prevent potential negative effects on the environment and human health.

WARNING

• Do not attempt to install or service this product by yourself. Installation or servicing of this

product by persons without training and experience in electronic equipment and automotive

accessories may be dangerous and could expose you to the risk of electric shock, injury or other

hazards.

• Do not attempt to operate the unit while driving. Make sure to pull off the road and park your vehicle

in a safe location before attempting to use the controls on the device.

CAUTION

• Do not allow this unit to come into contact with moisture and/or liquids. Electrical shock could result.

Also, damage to this unit, smoke, and overheating could result from contact with liquids.

• Always keep the volume low enough to hear outside sounds.

• The Pioneer CarStereo-Pass is for use only in Germany.

• This product is evaluated in moderate and tropical climate condition under the Audio, video and

similar electronic apparatus - Safety requirements, IEC 60065.

Before You Start

If you want to dispose this product, do not mix it with general household waste. There is a separate

collection system for used electronic products in accordance with legislation that requires proper

treatment, recovery and recycling.

CAUTION

This product is a class 1 laser product classified under the Safety of laser products, IEC 60825-1:2007.

3En

English

If you experience problems

Should this unit fail to work properly, please contact your dealer or nearest authorized PIONEER Service

Station.

DEH-X2900UI

Optional remote control

The remote control CD-R320 is sold separately.

Frequently used operations

Getting Started

Basic operation

Purpose Operation

Turn on the power* Press SRC

/OFF to turn on the power.

Press and hold SR

C/OFF to turn off the

power.

Adjust the volume Turn the M.

C. dial.

Select a source Press SRC

/OFF repeatedly.

Change the display information Press DISP re

peatedly.

Detach button

Display window

M.C. (multi-control) dial

BAND/

DISP (display)

SRC (source)/OFF

USB port

(eject)

AUX input jack (3.5 mm stereo jack)

Disc loading slot

* When this unit’s blue/white lead is connected to the vehicle’s auto-antenna relay control terminal,

the vehicle’s antenna extends when this unit’s source is turned on. To retract the antenna, turn the

source off.

Display indication

Detach the front panel to prevent theft. Remove any cables and devices attached to the

front panel and turn off the unit before detaching it.

Important

• Avoid subjecting the front panel to excessive shock.

• Keep the front panel out of direct sunlight and high temperatures.

• Always store the detached front panel in a protective case or bag.

Return to the previous display/list Press BAND/ .

Return to the normal display from the menu Press and hold BAND/ .

Indication Description

Appears when a lower tier of the menu or folder exists.

Appears when the button is pressed.

Appears when the local seek tuning function is set (page 9).

Appears when a traffic program is received.

Appears when the TA (traffic announcements) function is set (page 9).

Appears when the sound retriever function is set (page 10).

Appears when random/shuffle play is set.

Appears when repeat play is set.

Appears when the iPod control function is set (page 6).

Detaching the front panel

Purpose Operation

Detach Attach

4En

When you turn the ignition switch to ON after installation, [SET UP :YES] appears in the

di

splay.

1 Press the M.C. dial.

The setup menu disappears after 30 seconds of no operation. If you prefer not to set

at

this time, turn the M.C. dial to select [NO], then press to confirm.

2 Turn the M.C. dial to select the options, then press to confirm.

To proceed to the next menu option, you need to confirm your selection.

3 [QUIT :YES] appears when all the settings have been made.

To return to the first item of the setup menu, turn the M.C

. dial to select [QUIT :NO],

then press to confirm.

4 Press the M.C. dial to confirm the settings.

NOTES

• You can cancel the menu setting by pressing SRC/OFF.

• These settings can be made at any time from the SYSTEM settings (page 10) and INITIAL settings

(page 4).

1 Press the M.C. dial to display the main menu.

2 Turn the M.C. dial to select [SYSTEM], then press to confirm.

3 Turn the M.C. dial to select [DEMO OFF], then press to confirm.

4 Turn the M.C. dial to select [YES], then press to confirm.

Setup menu

Menu Item Description

LANGUAGE Select the language to display the text information from a

c

ompressed audio file.

[ENG](English),

[РУС

](Russian),

[TUR](Turkish)

CLOCK SET Set the clock.

FM STEP Select the FM tuning step from 100 kHz or 50 kHz.

[100], [50]

Canceling the demonstration display (DEMO OFF)

1 Press and hold SRC/OFF until the unit turns off.

2 Press and hold SRC/OFF to display the main menu.

3 Turn the M.C. dial to select [INITIAL], then press to confirm.

4 Turn the M.C. dial to select an option, then press to confirm.

The tuner frequencies on this unit are allocated for use in Western Europe, Asia, the

M

iddle East, Africa and Oceania. Use in other areas may result in poor reception. The RDS

(radio data system) function only works in areas that broadcast RDS signals for FM

stations.

INITIAL settings

Menu Item Description

FM STEP Select the FM tuning step from 100 kHz or 50 kHz.

[100], [50]

SP-P/O MODE Select when there is a full-range speaker connected to the rear

s

peaker output leads and there is a subwoofer connected to the

RCA output.

[REAR/SUB.W]

[SUB.W/SUB.W] Select when there is a passive subwoofer connected directly to

the rear speaker output leads and there is a subwoofer

connected to the RCA output.

[REAR/REAR] Select when there are full-range speakers connected to the rear

s

peaker output leads and RCA output. If there is a full-range

speaker connected to the rear speaker output leads, and the

RCA output is not used, you may select either [REAR/SUB.W] or

[REAR/REAR].

S/W UPDATE Select to confirm the latest system information on the unit.

[SYSTEM INFO]

[SYSTEM UPDATE] Select to update the unit to the latest software and initialize the

u

nit settings. For details on the latest software and updating,

visit our website.

SYSTEM RESET Select [YES] to initialize the unit settings. The unit will be

restarted automatically.

(Some of the settings may be retained even after resetting the

uni

t.)

[YES], [NO]

Radio

5En

English

1 Press SRC/OFF to select [RADIO].

2 Press BAND/ to select the band from [FM1], [FM2], [FM3], [MW] or [LW].

3 Press a number button (1/ to 6/ ).

TIP

The / buttons can be also used to select a preset station when [SEEK] is set to [PCH] in the

FUNCTION settings (page 9).

The six strongest stations are stored on the number buttons (1/ to 6/ ).

1 After selecting the band, press the M.C. dial to display the main menu.

2 Turn the M.C. dial to select [FUNCTION], then press to confirm.

3 Turn the M.C. dial to select [BSM], then press to confirm.

To seek a station manually

1 After selecting the band, press / to select a station.

Press and hold / then release to seek an available station. Scanning stops

when the unit receives a station. To cancel seek tuning, press / .

NOTE

[SEEK] needs to be set to [MAN] in the FUNCTION settings (page 9).

To store stations manually

1 While receiving the station you want to store, press and hold one of the number

buttons (1/ to 6/ ) until it stops flashing.

The unit searches for a station by PTY (program type) information.

1 Press during FM reception.

2 Turn the M.C. dial to select a program type from [NEWS/INFO], [POPULAR],

[CLASSICS] or [OTHERS].

3 Press the M.C. dial.

Receiving preset stations

Best stations memory (BSM)

Using PTY functions

The unit begins to search for a station. When it is found, its program service name is

displayed.

NOTES

• To cancel the search, press the M.C. dial.

• The program of some stations may differ from that indicated by the transmitted PTY.

• If no station is broadcasting the type of program you searched for, [NOT FOUND] is displayed for

about two seconds and then the tuner returns to the original station.

Disconnect headphones from the device before connecting it to the unit.

CD

1 Insert a disc into the disc loading slot with the label side up.

To eject a disc, stop playback first then press .

USB devices (including Android™)/iPod

1 Open the USB port cover.

2 Plug in the USB device/iPod using an appropriate cable.

NOTE

To automatically switch to [USB] source when a USB device/iPod is connected to the unit, set [USB

AUTO] to [ON] in the SYSTEM settings (page 11).

CAUTION

Use an optional Pioneer USB cable (CD-U50E) to connect the USB device as any device connected

directly to the unit will protrude out from the unit, which could be dangerous.

Before removing the device, stop playback.

AOA connections

For details on AOA connection, see page 8.

MTP connection

A device installed with Android OS 4.0 or later can be connected to the unit via MTP, using the cable

supplied with the device. However, depending on the connected device and the numbers of the files in

the device, audio files/songs may not be able to be played back via MTP. Note that MTP connection is

not compatible with WAV file formats, and cannot be used with the MIXTRAX function.

CD/USB/iPod/AUX

Playing back

6En

NOTE

If you use an MTP connection, [ANDROID WIRED] needs to be set to [MEMORY] in the SYSTEM settings

(page 11).

AUX

1 Insert the stereo mini plug into the AUX input jack.

2 Press SRC/OFF to select [AUX] as the source.

NOTE

If [AUX] is set to [OFF] in the SYSTEM settings, [AUX] cannot be selected as a source (page 11).

You can make various adjustments in the FUNCTION settings (page 9).

Note that the following operations do not w

ork for an AUX device. To operate an AUX

device, use the device itself.

Operations

Purpose Operation

Select a folder/album*1 Press 1/ or 2/ .

Select a track/song (chapter) Press or .

Fast forward or reverse*3 Press and hold or .

Search for a file from a list 1 Press to display the list.

2 Tu

rn the M.C. dial to select the desired

file (folder) name or category, then press

to confirm.

3 Tu

rn the M.C. dial to select the desired

file, then press to confirm.

Playback starts.

View a list of the files in the selected folder/

category*1

Press the M.C. dial when a folder/category

is selected.

Play a song in the selected folder/

cat

egory*1

Press and hold the M.C. dial when a folder/

category is selected.

Alphabetical search (iPod only) 1 P

ress to display the list.

2 Tu

rn the M.C. dial to select the desired

category list, then press to enter the

alphabetical search mode.

(Turning the M.

C. dial twice also enters

the alphabetical search mode.)

3 Tu

rn the M.C. dial to select a letter, then

press to display the alphabetical list.

To cancel alphabetical search, press BA

ND/

.

*1 Compressed audio files only

*2 This function is disabled when USB is selected as a source and the MIXTRAX function is on.

*3 When you use the fast forward or reverse function while playing a VBR file, the playback time may

be not correct.

Link play mode

You can access songs based on the artist, album, or genre currently playing.

1 While listening to a song, press and hold to enter the link play mode.

2 Turn the M.C. dial to select the mode ([ARTIST], [ALBUM], [GENRE]), then press to

confirm.

The selected song/album will be played after the currently playing song.

NOTE

The selected song/album may be canceled if you use functions other than those from the link play

mode (e.g. fast forward and reverse).

iPod control

You can control the unit via a connected iPod.

The following iPod models are not compatible with this function.

–iPod nano 1st generation, iPod with video

1 Press BAND/ during playback, then select the control mode.

[CO

NTROL iPod]: The unit’s iPod function can be operated from the connected iPod.

Repeat play Press 6/ .

Random/shuffle play Press 5/ .

Shuffle all play (iPod only) Press and hold 5/ .

Pause/resume playback Press 4/PA

USE.

Sound retriever*1*2 Press 3/S.

Rtrv.

[1]: Effective for low compression rates

[2]: Effective for high compression rates

Return to root folder (CD/USB only)*1 Press and hold .

Switch between compressed audio and CD-

DA (

CD only)

Press BAND/ .

Change drives in USB device

(Devices that support the USB mass storage

device class protocol only)

Press BAND/ .

Useful functions for iPod

Purpose Operation

7En

English

[CONTROL AUDIO]: The unit’s iPod function can only be operated by the buttons on

the unit. In this mode, the connected iPod cannot be turned on or off.

NOTES

• Switching the control mode to [CONTROL iPod] pauses song playback. Use the connected iPod to

resume playback.

• The following operations are still accessible from the unit, even if the control mode is set to

[CONTROL iPod].

– Pause, fast forward/reverse, song/chapter selection

• The volume can only be adjusted from the unit.

The MIXTRAX function creates a non-stop mix of your music library, accompanied by

illumination effects. For details on MIXTRAX settings, see page 12.

NOTES

• This function is not compatible with an Android device connected via MTP.

• When USB is selected as a source and the MIXTRAX function is in use, the sound retriever function is

disabled.

• Depending on the file/song, sound effects may not be available.

• Turn the MIXTRAX function off if the illumination effects it produces interfere with driving.

1 Press MIX to turn MIXTRAX on/off.

You can enjoy listening to an application on an iPhone via the unit. In some cases, you

c

an control an application by using the unit.

For details on compatible devices, visit our website.

Important

Use of third party apps may involve or require the provision of personally identifiable information,

whether through the creation of a user account or otherwise, and for certain applications, the provision

of geolocation data.

ALL THIRD PARTY APPS ARE THE SOLE RESPONSIBILITY OF THE PROVIDERS, INCLUDING WITHOUT

LIMITATION COLLECTION AND SECURITY OF USER DATA AND PRIVACY PRACTICES. BY ACCESSING

THIRD PARTY APPS, YOU AGREE TO REVIEW THE TERMS OF SERVICE AND PRIVACY POLICIES OF THE

PROVIDERS. IF YOU DO NOT AGREE WITH THE TERMS OR POLICIES OF ANY PROVIDER OR DO NOT

CONSENT TO THE USE OF GEOLOCATION DATA WHERE APPLICABLE, DO NOT USE THAT THIRD PARTY

APP.

For iPhone users

This function is compatible with iPhones and iPod touches installed with iOS 5.0 or later.

About MIXTRAX (USB/iPod only)

App Mode

NOTE

PIONEER IS NOT LIABLE FOR ANY THIRD PARTY APPS OR CONTENT, INCLUDING WITHOUT LIMITATION

THEIR ACCURACY OR COMPLETENESS. THE CONTENT AND FUNCTIONALITY OF SUCH APPS ARE THE

SOLE RESPONSIBILITY OF THE APP PROVIDER.

1 Connect this unit with the mobile device.

• i

Phone via USB (page 5)

2 Press SRC/OFF to select [APP].

3 Operate the mobile device to start up the application.

Basic operations

You can make various adjustments in the FUNCTION settings (page 9).

(DEH-X2900UI is only compatible with Spotify installed on iPhone.)

Spotify is a music streaming distribution service not affiliated with Pioneer. More

i

nformation is available at http://www.spotify.com.

The Spotify application is available for compatible smartphones, please visit https://

sup

port.spotify.com/ for the latest compatibility information.

To enjoy Spotify as you drive, first download the Spotify app to your iPhone. You can

d

ownload it on the iTunes App Store. Choose a free account or a paid Premium account,

either in the app or at spotify.com. A Premium account gives you more features, like

offline listening.

Important

• This product incorporates Spotify software which is subject to 3rd party licenses found here:

www.spotify.com/connect/third-party-licenses.

• For information on the countries and regions where Spotify can be used, take a look at https://

www.spotify.com/us/select-your-country/.

Playback of an application via the unit

Purpose Operation

Select a track Press or .

Fast forward or reverse Press and hold or .

Pause/resume playback Press BA

ND/ .

Spotify®

8En

Update the firmware of the Spotify application to the latest version before use.

1 Connect this unit with the mobile device.

• iP

hone via USB (page 5)

2 Press SRC/OFF to select [SPOTIFY].

3 Launch the Spotify application on the mobile device and start playback.

Basic operations

You can make various adjustments in the FUNCTION settings (page 9).

NOTE

The available operations may vary according to the type of contents (track/album/artist/playlist/radio)

you want to play.

NOTE

Some functions of Spotify may not be operated from the unit.

Listening to Spotify

Purpose Operation

Skip a track Press or .

Search for a track from a list 1 Press (list) to display the list.

2 Tu

rn the M.C. dial to select the desired

category, then press to confirm.

3 Tu

rn the M.C. dial to select the desired

file, then press to confirm.

Playback starts.

Pause/resume playback Press 4/

PAUSE.

Thumbs Up (Only for radio) Press 1/ .

Thumbs Down (Only for radio) Press 2/ .

Random play (Only for track/album/artist/

pl

aylist)

Press 5/ .

Repeat play (Only for track/album/artist/

pl

aylist)

Press 6/ .

Start a radio channel based on the song

cur

rently being played.

1 Press and hold (list) to start a radio.

2 P

ress the M.C. dial.

• T

his function may not be available

depending on the selected song.

Store the information about the song

cur

rently being played.

Remove the song information stored.

1 Press and hold 3/S.Rtrv.

[SAVE]/[UNSAVE] appears.

2 P

ress the M.C. dial.

You can operate the unit from Pioneer ARC APP installed on an iPhone/Android device.

In some cases, you can control aspects of the application, such as source selection,

pause, etc., by using the unit.

For details on what operations are available on the application, see the application’s help

section.

WARNING

Do not attempt to operate the application while driving. Make sure to pull off the road and park your

vehicle in a safe location before attempting to use the controls on the application.

For iPhone users

This function is compatible with iPhones (iPhone 5 or later) and iPod touches installed

wit

h iOS 8.0 or later.

You can download Pioneer ARC APP on iTunes App Store.

For Android device users

This function is compatible with devices that have Android OS 4.1 or later installed and

also sup

port AOA (Android Open Accessory) 2.0.

You can download Pioneer ARC APP on Google Play™.

NOTE

Some Android devices connected via AOA 2.0 may not work properly or emit sounds due to their own

software design, regardless of the OS version.

1 Connect this unit with the mobile device.

• i

Phone/Android device via USB (page 5)

Proceed to step 6 if you select the USB connection for iPhone.

2 Press the M.C. dial to display the main menu.

3 Turn the M.C. dial to select [SYSTEM], then press to confirm.

4 Turn the M.C. dial to select [ANDROID WIRED], then press to confirm.

5 Turn the M.C. dial to select [APP CONTROL] for an Android device connected via

USB.

If [ON] is selected in [P.APP AUTO ON] (page 11), Pioneer ARC APP on the Android

device starts automatically, and all the steps are finished.

Using Pioneer ARC APP

Making a connection with Pioneer ARC APP

9En

English

NOTE

If Pioneer ARC APP has not been installed on your Android device yet, a message that prompts you

to install the application will appear on your Android device. Select [OFF] in [P.APP AUTO ON] to

clear the message (page 11).

6 Press SRC/OFF to select any source.

7 Launch Pioneer ARC APP on the mobile device.

NOTE

You can also launch the application by pressing and holding the M.C. dial for iPhone.

1 Press SRC/OFF to select [ANDROID].

Basic operations

You can adjust various settings in the main menu.

1 Press the M.C. dial to display the main menu.

2 Turn the M.C. dial to select one of the categories below, then press to confirm.

• FUNCTION settings (page 9)

• AUDIO settings (page 10)

• SYSTEM settings (page 10)

• ILLUMINATION settings (page 11)

• MIXTRAX settings (page 12)

3 Turn the M.C. dial to select the options, then press to confirm.

Listening to music on Android

Purpose Operation

Select a track Press or .

Fast forward or reverse Press and hold or .

Pause/resume playback Press 4/PA

USE.

Sound retriever Press 3/S.

Rtrv.

[1]: Effective for low compression rates

[2]: Effective for high compression rates

Settings

The menu items vary according to the source.

FUNCTION settings

Menu Item Description

FM SETTING

[TALK], [STANDARD], [MUSIC] Match the sound quality level with the broadcast

s

ignal conditions of the FM band signal.

(Available only when FM band is selected.)

BSM

Store the six strongest stations on the number

but

tons (1/ to 6/ ) automatically.

REGIONAL

[ON], [OFF] Limit the reception to the specific regional

programs when AF (alternative frequencies

search) is selected. (Available only when FM

band is selected.)

LOCAL

FM: [

OFF], [LV1], [LV2], [LV3], [LV4]

MW/LW: [O

FF], [LV1], [LV2]

Restrict the tuning station according to the

si

gnal strength.

TA

[ON], [OFF] Receive current traffic information if available.

(

Available only when FM band is selected.)

AF

[ON], [OFF] Allow the unit to retune to a different frequency

pro

viding the same station. (Available only when

FM band is selected.)

NEWS

[ON], [OFF] Interrupt the currently selected source with

n

ews programs. (Available only when FM band is

selected.)

SEEK

[MAN], [PCH] Assign or buttons to seek the stations

one by one (manual tuning) or select a station

f

rom the preset channels.

SAVE

Store the information about the song currently

bei

ng played to your music list on Spotify.

10En

UNSAVE

Remove the song information stored in [SAVE].

S.RTRV

[1] (effective for low compression

ra

tes),

[2] (effective for high

co

mpression rates),

[OFF]

Enhance compressed audio and restore rich

so

und.

Not available when:

• U

SB is selected as a source and the MIXTRAX

function is set to on.

• C

D-DA/CD-TEXT is played back.

AUDIO BOOK

[FASTER], [NORMAL], [SLOWER] Change the playback speed. (Not available when

[C

ONTROL iPod] is selected in the control mode.)

PAUSE

Pause or resume playback.

AUDIO settings

Menu Item Description

FADER*1

Adjust the front and rear speaker balance.

BALANCE

Adjust the left and right speaker balance.

EQ SETTING

[SUPER BASS], [POWERFUL],

[NATURAL], [VOCAL], [CUSTOM1],

[CUSTOM2], [FLAT]

Select an equalizer band and

level fo

r further customising.

Equalizer band: [80H

Z], [250HZ],

[800HZ], [2.5KHZ], [8KHZ]

Equalizer level: [+

6] to [–6]

Select or customise the equalizer curve.

[CUSTOM1] can be set separately for each source.

H

owever, each of the below combinations are set

to the same setting automatically.

• U

SB, iPod, ANDROID, SPOTIFY, and APP

(iPhone)

[CUSTOM2] is a shared setting used for all

so

urces.

LOUDNESS

[OFF], [LOW], [MID], [HI] Compensate for clear sound at low volume.

Menu Item Description

USB

iPod

*1 Not available when [SUB.W/SUB.W] is selected in [SP-P/O MODE] in the INITIAL settings (page 4).

*2 Not available when [REAR/REAR] is selected in [SP-P/O MODE] in the INITIAL settings (page 4).

*3 Not available when [OFF] is selected in [SUB.W].

You can also access to these menus when the unit is turned off.

SUB.W*2

[NOR], [REV], [OFF] Select the subwoofer phase.

SUB.W CTRL*2

*3

Cut-off frequency: [50H

Z],

[63HZ], [80HZ], [100HZ], [125HZ],

[160HZ], [200HZ]

Output level:

[–24] to [+6]

Slope level: [–12

], [–24]

Only frequencies lower than those in the

sel

ected range are output from the subwoofer.

BASS BOOST

[0] to [+6] Select the bass boost level.

HPF SETTING

Cut-off frequency: [

OFF], [50HZ],

[63HZ], [80HZ], [100HZ], [125HZ],

[160HZ], [200HZ]

Slope level: [–12

], [–24]

Only frequencies higher than the high-pass filter

(

HPF) cutoff are output from the speakers.

SLA

[+4] to [–4] Adjust the volume level for each source except

FM

.

Each of the below combinations are set to the

s

ame setting automatically.

• U

SB, iPod, ANDROID, SPOTIFY, and APP

(iPhone)

SYSTEM settings

Menu Item Description

LANGUAGE

[ENG](English), [РУС](Russian),

[TUR](Turkish)

Select the language to display the text

information from a compressed audio file.

CLOCK SET

Set the clock (page 4).

12H/24H

[12H], [24H] Select the time notation.

Menu Item Description

11En

English

* [PW SAVE] is canceled if the vehicle battery is disconnected and will need to be turned back on once

the battery is reconnected. When [PW SAVE] is off, depending on connection methods, the unit may

continue to draw power from the battery if your vehicle’s ignition does not have an ACC (accessory)

position.

AUTO PI

[ON], [OFF] Search for a different station with the same

pro

gramming, even if using a preset station.

AUX

[ON], [OFF] Set to [ON] when using an auxiliary device

c

onnected to the unit.

SPOTIFY

[ON], [OFF] Set to [ON] when using the Spotify function.

PW SAVE*

[ON], [OFF] Reduce the battery power consumption.

Turning on the source is the only operation

al

lowed when this function is on.

ANDROID WIRED

[MEMORY], [APP CONTROL] Select the appropriate connection method for an

A

ndroid device.

P.A P P AUTO O N

[ON], [OFF]

Select [ON] to automatically launch Pioneer ARC

APP when an Android device is connected to the

unit via AOA. (Not available when [MEMORY] is

selected in [ANDROID WIRED].)

USB AUTO

[ON], [OFF] Select [ON] to automatically switch to [USB]

so

urce when a USB device/iPod is connected to

the unit.

Select [OFF] when a USB device/iPod is being

connected to the unit just for charging.

Menu Item Description

ILLUMINATION settings

Menu Item Description

COLOUR

[KEY COLOUR], [DISP COLOUR],

[BOTH COLOUR]

Select colour for the keys/display of the unit from

12 preset colours, [SCAN] or [CUSTOM]*.

• [

SCAN]: Cycle through a variety of colours

automatically.

• [C

USTOM]*:

1 P

ress and hold the M.C. dial until the colour

setting display appears.

2 S

et the primary colour (R (red)/G (green)/B

(blue)) and brightness level ([0] to [60]).

You cannot select a level below 10 for all three

of

R (red), G (green), B (blue) at the same time.

You can also customise the preset colours. Select

o

ne of the preset colours, then press and hold

the M.C. dial until the colour setting display

appears.

* The CUSTOM setting is only available for [KEY

COLOUR] and [DISP COLOUR].

DIM SETTING

[SYNC ILLUMI], [SYNC CLOCK],

[MA

NUAL]

Change the display brightness.

BRIGHTNESS

[KEY], [DISP] Select the brightness for the keys/display of the

uni

t from [1] to [10].

The available setting ranges differ depending on

[D

IM SETTING].

ILLUMI FX

[ON], [OFF] The illumination effect can be seen when a CD is

in

serted/ejected.

The illumination effect will activate when the

A

CC power is turned on/off regardless of this

setting.

12En

MIXTRAX settings

Menu Item Description

SHORT PLAYBCK

[1.0 MIN], [1.5 MIN], [2.0 MIN],

[2.5 MIN], [3.0 MIN], [OFF]

Select the length of the playback time.

FLASH AREA

[KEY/DISPLAY], [KEY], [OFF] Select the area for the illumination effect.

When [OFF] is selected, the colour set under

th

e ILLUMINATION settings (page 11) is used as

the display colour.

FLASH PATTERN

[SOUND LEVEL 1] to [SOUND LEVEL

6]

Change the illumination effect according to

t

he sound and bass level.

The flash pattern changes according to the

so

und level.

[LOW PASS 1] to [LOW PASS 6] The flash pattern changes according to the

bas

s level.

[RANDOM1] The flash pattern changes randomly according

t

o the sound level mode and low pass mode.

[RANDOM2] The flash pattern changes randomly according

t

o the sound level mode.

[RANDOM3] The flash pattern changes randomly according

t

o the low pass mode.

DISPLAY FX

[ON], [OFF] Set the MIXTRAX special effects on/off.

CUT IN FX

[ON], [OFF] Turn the MIXTRAX sound effects on/off while

m

anually changing the tracks.

Important

• When installing this unit in a vehicle

without an ACC (accessory) position on

the ignition switch, failure to connect the

red cable to the terminal that detects

operation of the ignition key may result

in battery drain.

• Use of this unit in conditions other than

the following could result in fire or

malfunction.

–Vehicles with a 12-volt battery and

neg

ative grounding.

–When speaker output is used by 4

chan

nels, use speakers over 50 W

(maximum input power) and between 4

Ω to 8 Ω (impedance value). Do not use

1 Ω to 3 Ω speakers for this unit.

–When rear speaker output is used by 2

Ω

of subwoofer, use speakers over 70 W

(maximum input power).

* Please refer to connections for a

co

nnection method.

• T

o prevent a short-circuit, overheating or

malfunction, be sure to follow the

directions below.

–Disconnect the negative terminal of the

bat

tery before installation.

–Secure the wiring with cable clamps or

a

dhesive tape. Wrap adhesive tape

around wiring that comes into contact

with metal parts to protect the wiring.

– Place all cables away from moving parts,

su

ch as the shift lever and seat rails.

–Place all cables away

from hot places,

such as near the heater outlet.

–Do not connect the yellow cable to the

bat

tery by passing it through the hole

to the engine compartment.

–Cover any disconnected cable

co

nnectors with insulating tape.

–Do not shorten any cables.

–Never cut the insulation of the power

cabl

e of this unit in order to share the

power with other devices. The current

capacity of the cable is limited.

–Use a fuse of the rating prescribed.

–Never wire the negative speaker cable

di

rectly to ground.

–Never band together negative cables of

m

ultiple speakers.

• When t

his unit is on, control signals are

sent through the blue/white cable.

Connect this cable to the system remote

control of an external power amp or the

vehicle’s auto-antenna relay control

terminal (max. 300mA 12 V DC). If the

vehicle is equipped with a glass antenna,

connect it to the antenna booster power

supply terminal.

• Nev

er connect the blue/white cable to

the power terminal of an external power

amp. Also, never connect it to the power

terminal of the auto antenna. Doing so

may result in battery drain or a

malfunction.

• T

he black cable is ground. Ground cables

for this unit and other equipment

(especially, high-current products such as

power amps) must be wired separately. If

they are not, an accidental detachment

may result in a fire or malfunction.

• Th

e graphical symbol placed on

the product means direct current.

Connections/Installation

Connections

ACC position No ACC position

13En

English

This unit

Power cord input

Rear AUX IN | [Tel In] (3.5mm stereo jack)

A dedicated rear input that is only

com

patible with external Bluetooth

hands-free telephone kits. The audio

signal is muted during a phone call

when the yellow/black wire is

connected/activated.

Rear output or subwoofer output

Front output

Antenna input

Fuse (10 A)

Wired remote input

Hard-wired remote control adapter can

be connec

ted (sold separately).

Power cord

To power cord input

Depending on the kind of vehicle, the

function of and may be different.

In this case, be sure to connect to

and to .

Yel low

Back-up (or accessory)

Yel low

Connect to the constant 12 V supply

te

rminal.

Red

Accessory (or back-up)

Red

Connect to terminal controlled by the

ign

ition switch (12 V DC).

Connect leads of the same colour to

each other.

Black (chassis ground)

Blue/white

The pin position of the ISO connector

w

ill differ depending on the type of

vehicle. Connect and when Pin 5

is an antenna control type. In another

t

ype of vehicle, never connect and

.

Blue/white

Connect to the system control terminal

of

the power amp (max. 300 mA 12 V

DC).

Blue/white

Connect to the auto-antenna relay

c

ontrol terminal (max. 300 mA 12 V DC).

Speaker leads

White: Front left

White/black: Front left

Gray: Front right

Gray/black: Front right

Green: Rear left or subwoofer

Green/black: Rear left or subwoofer

Violet: Rear right or subwoofer

Violet/black: Rear right or subwoofer

Orange/white

Connect to a car’s illumination signal.

ISO connector

In some vehicles, the ISO connector

may be divided into two. In this case, be

sure to connect to both connectors.

NOTES

• Change the initial menu of this unit. Refer

to [SP-P/O MODE]

(page 4). The

subwoofer output of this unit is

mo

naural.

• W

hen using a subwoofer of 2 Ω, be sure

to connect the subwoofer to the violet

and violet/black leads of this unit. Do not

connect anything to the green and

green/black leads.

Power amp (sold separately)

Perform these connections when using the

optional amplifier.

System remote control

Connect to blue/white cable.

Power amp (sold separately)

Connect with RCA cables (sold

separately)

To front output

Front speaker

To rear output or subwoofer output

Rear speaker or subwoofer

Important

• Check all connections and systems before

final installation.

• Do not use unauthorized parts as this

may cause malfunctions.

• Consult your dealer if installation requires

drilling of holes or other modifications to

the vehicle.

• Do

not install this unit where:

– it may interfere with operation of the

vehicl

e.

– it may cause injury to a passenger as a

r

esult of a sudden stop.

• T

he semiconductor laser will be damaged

if it overheats. Install this unit away from

hot places such as near the heater outlet.

• Opt

imum performance is

obtained when the unit is

installed at an angle of less

than 60°.

• W

hen installing, to ensure proper heat

dispersal when using this unit, make sure

you leave ample space behind the rear

panel and wrap any loose cables so they

are not blocking the vents.

DIN mount installation

1 Insert the supplied mounting sleeve

into the dashboard.

2 Secure the mounting sleeve by using a

screwdriver to bend the metal tabs

(90°) into place.

Dashboard

Mounting sleeve

Installation

Leave ample

space

5 cm

14En

• Make sure that the unit is installed

securely in place. An unstable

installation may cause skipping or

other malfunctions.

When not using the supplied

mounting sleeve

1 Determine the appropriate position

where the holes on the bracket and

the side of the unit match.

2 Tighten two screws on each side.

Tapping screw (5 mm × 9 mm, not

supplied with product)

Mounting bracket

Dashboard or console

Removing the unit (installed with

the supplied mounting sleeve)

1 Remove the trim ring.

Trim ring

Notched tab

• R

eleasing the front panel allows easier

access to the trim ring.

• Wh

en reattaching the trim ring, point

the side with the notched tab down.

2 Insert the supplied extraction keys

into both sides of the unit until they

click into place.

3 Pull the unit out of the dashboard.

The display automatically returns to the

normal display.

→ No operations have been made for

about 30 seconds.

– Perform an operation.

The repeat play range changes

unexpectedly.

→ Depending on the repeat play range,

the selected range may change when

another folder or track is being selected

or during fast forwarding/reversing.

– Select the repeat play range again.

A subfolder is not played back.

→ Subfolders cannot be played when

[FLD] (folder repeat) is selected.

– Select another repeat play range.

The sound is intermittent.

→ You are using a device, such as a cellular

phone, that may cause audible

interference.

– Move electrical devices that may be

c

ausing the interference away from

the unit.

Common

AMP ERROR

→ This unit fails to operate or the speaker

connection is incorrect.

→ T

he protective circuit is activated.

– Check the speaker connection.

– Turn the ignition switch OFF and back

t

o ON again. If the message remains,

contact your dealer or an authorized

Pioneer Service Station for assistance.

NO XXXX (NO TITLE, for example)

→ There is no embedded text information.

– Switch the display or play another

tr

ack/file.

CD player

ERROR-07, 11, 12, 17, 30

→ The disc is dirty.

–Clean the disc.

→ T

he disc is scratched.

– Replace the disc.

ERROR-07, 10, 11, 12, 15, 17, 30, A0

→ There is an electrical or mechanical

error.

– Turn the ignition switch OFF and back

to

ON, or switch to a different source,

then back to the CD player.

ERROR-15

→ The inserted disc is blank.

– Replace the disc.

ERROR-23

→ Unsupported CD format.

– Replace the disc.

FORMAT READ

→ Sometimes there is a delay between the

start of playback and when you start to

hear any sound.

– Wait until the message disappears and

y

ou hear sound.

NO AUDIO

→ The inserted disc does not contain any

playable files.

– Replace the disc.

SKIPPED

→ The inserted disc contains DRM

protected files.

– The protected files are skipped.

Additional Information

Troubleshooting

Error messages

15En

English

PROTECT

→ All the files on the inserted disc are

embedded with DRM.

– Replace the disc.

USB device/iPod

FORMAT READ

→ Sometimes there is a delay between the

start of playback and when you start to

hear any sound.

– Wait until the message disappears and

y

ou hear sound.

NO AUDIO

→ There are no songs.

–Transfer the audio files to the USB

de

vice and connect.

→ The co

nnected USB device has security

enabled.

– Follow the USB device instructions to

d

isable the security.

SKIPPED

→ The connected USB device contains

DRM protected files.

– The protected files are skipped.

PROTECT

→ All the files on the connected USB

device are embedded with DRM.

– Replace the USB device.

N/A USB

→ The connected USB device is not

supported by this unit.

– Disconnect your device and replace it

wit

h a compatible USB device.

HUB ERROR

→ The USB device connected via a USB

hub is not supported by this unit.

– Connect the USB device directly to this

u

nit using a USB cable.

CHECK USB

→ The USB connector or USB cable has

short-circuited.

–Check that the USB connector or USB

cable is

not caught in something or

damaged.

→ The co

nnected USB device consumes

more than maximum allowable current.

–Disconnect the USB device and do not

use it

. Turn the ignition switch OFF

and back to ACC or ON. Connect only

compliant USB devices.

→ The

iPod operates correctly but does

not charge.

–Make sure the connection cable for

t

he iPod has not shorted out (e.g., not

caught in metal objects). After

checking, turn the ignition switch OFF

and back to ON, or disconnect the

iPod and reconnect.

ERROR-19

→ Communication failed.

–Perform one of the following

op

erations, then return to the USB

source.

• T

urn the ignition switch OFF and

back to ON.

• Di

sconnect the USB device.

• C

hange to a different source.

→ iP

od failure.

–Disconnect the cable from the iPod.

O

nce the iPod’s main menu is

displayed, reconnect the iPod and

reset it.

ERROR-23

→ USB device was not formatted properly.

–Format the USB device with FAT12,

FAT

16 or FAT32.

ERROR-16

→ The iPod firmware version is old.

–Update the iPod version.

→ iP

od failure.

–Disconnect the cable from the iPod.

O

nce the iPod’s main menu is

displayed, reconnect the iPod and

reset it.

STOP

→ There are no songs in the current list.

– Select a list that contains songs.

NOT FOUND

→ No related songs.

– Transfer songs to the iPod.

Apps

START UP APP

→ The application has not started running

yet.

– Operate the mobile device to start up

t

he application.

Spotify

CHECK APP

→ Connection to the Spotify application

failed.

– Follow the instructions that appear on

t

he screen.

Discs and player

• Use only discs that feature either of the

following two logos.

• Use 12-cm discs.

• U

se only conventional, fully circular discs.

• T

he following types of discs cannot be

used with this unit:

–DualDiscs

–8-cm discs: Attempts to use such discs

w

ith an adaptor may cause the unit to

malfunction.

–Oddly shaped discs

–Discs other than CDs

–Damaged discs, including discs that are

cra

cked, chipped or warped

–CD-R/RW discs that have not been

fi

nalized

• D

o not write on or apply chemicals to the

surface of the discs.

• T

o clean a CD, wipe the disc with a soft

cloth outward from the center.

• C

ondensation may temporarily impair

the player’s performance. Let it rest for

about one hour to adjust to a warmer

temperature. Also, wipe any damp discs

off with a soft cloth.

• W

hen using discs that can be printed on

label surfaces, check the instructions and

the warnings of the discs. Depending on

the discs, inserting and ejecting may not

be possible. Using such discs may result

in damage to this equipment.

• D

o not attach commercially available

labels or other materials to the discs.

– The discs may warp making the disc

unpl

ayable.

– The labels may come off during

play

back and prevent ejection of the

discs, which may result in damage to

the equipment.

USB storage device

• Connections via USB hubs are not

supported.

• F

irmly secure the USB storage device

before driving. Do not let the USB storage

device fall onto the floor, where it may

become jammed under the brake or

accelerator pedal.

• D

epending on the USB storage device,

the following problems may occur.

–Operations may vary.

– The storage device may not be

reco

gnized.

– Files may not be played back properly.

– The device may cause audible

int

erference when you are listening to

the radio.

Handling guidelines

16En

iPod

• Do not leave the iPod in places with high

temperatures.

• F

irmly secure the iPod when driving. Do

not let the iPod fall onto the floor, where

it may become jammed under the brake

or accelerator pedal.

• The se

ttings of the iPod such as the

equalizer and repeat play are changed

automatically when the iPod is

connected to the unit. Once the iPod is

disconnected, those settings will return

to the original settings.

• I

ncompatible text saved on the iPod will

not be displayed by the unit.

• Only the first 32 characters can be

displayed as a file name (including the file

extension) or a folder name.

• The uni

t may not work properly

depending on the application used to

encode WMA files.

• There m

ay be a slight delay at the start of

the playback of audio files embedded

with image data, or audio files stored on a

USB device with numerous folder

hierarchies.

• R

ussian text to be displayed on this unit

should be encoded in one of the

following character sets:

–Unicode (UTF-8, UTF-16)

–A character set other than Unicode that

is use

d in a Windows environment and

is set to Russian in the multi-language

setting

CAUTION

• Pioneer cannot guarantee compatibility

with all USB mass storage devices, and

assumes no responsibility for any loss of

data on media players, smartphones, or

other devices while using this product.

• Do not leave discs or a USB storage

device in any place that is subject to high

temperatures.

WMA files

MP3 files

WAV files

• WAV file formats cannot be connected via

MTP.

Compressed audio

compatibility

File extension .wma

Bit rate 48 kbps to 320 kbps

(CBR), 48 kbps to 384

kbps (VBR)

Sampling frequency 32 kHz, 44.1 kHz, 48

kHz

Windows Media™

Audio Professional,

Lossless, Voice/DRM

Stream/Stream with

video

Not compatible

File extension .mp3

Bit rate 8 kbps to 320 kbps

(CBR), VBR

Sampling frequency 8 kHz to 48 kHz (32

kHz, 44.1 kHz, 48 kHz

for emphasis)

Compatible ID3 tag

version

1.0, 1.1, 2.2, 2.3, 2.4

(ID3 tag Version 2.x is

given priority over

Version 1.x.)

M3u playlist Not compatible

MP3i (MP3

interactive), mp3 PRO

Not compatible

File extension .wav

Quantization bits 8 and 16 (LPCM), 4

(MSADPCM)

Sampling frequency 16 kHz to 48 kHz

(LPCM), 22.05 kHz and

44.1 kHz (MS ADPCM)

Disc

• Regardless of the length of the blank

section between the songs from the

original recording, compressed audio

discs play with a short pause between

songs.

USB device

• There may be a slight delay when starting

playback of audio files on a USB storage

device with numerous folder hierarchies.

This unit supports only the following iPod

models. Supported iPod software versions are

shown below. Older versions may not be

supported.

Made for

–iPod touch (1st through 6th generation)

–iPod classic

–iPod with video

–iPod nano (1st through 7th generation)

–iPhone 6s

– iPhone 6s Plus

–iPhone 6

–iPhone 6 Plus

–iPhone 5s

–iPhone 5c

–iPhone 5

–iPhone 4s

–iPhone 4

–iPhone 3GS

–iPhone 3G

–iPhone

• O

perations may vary depending on the

generation and/or software version of

the iPod.

• U

sers of iPod with the Lightning

Connector should use the Lightning to

USB Cable (supplied with iPod).

• U

sers of iPod with the Dock Connector

should use the CD-IU51. For details,

consult your dealer.

• Refer t

o the iPod manuals for information

about the file/format compatibility.

• A

udiobook, Podcast: Compatible

CAUTION

Pioneer accepts no responsibility for data

lost on the iPod, even if that data is lost

while this unit is used.

The user cannot assign folder numbers and

specify playback sequences with this unit.

Sequence of audio file depends on the

connected device.

Note that the hidden files in a USB device

can

not be played back.

Playable folder

hierarchy

Up to eight tiers (A

practical hierarchy is

less than two tiers.)

Playable folders Up to 99

Playable files Up to 999

File system ISO 9660 Level 1 and

2, Romeo, Joliet

Multi-session

playback

Compatible

Packet write data

transfer

Not compatible

Playable folder

hierarchy

Up to eight tiers (A

practical hierarchy is

less than two tiers.)

Playable folders Up to 500

Playable files Up to 15 000

Playback of copyright-

protected files

Not compatible

Partitioned USB

device

Only the first partition

can be played.

iPod compatibility

Sequence of audio files

17En

English

Example of a hierarchy

iTunes

Apple and iTunes are trademarks of Apple

I

nc., registered in the U.S. and other

countries.

WMA

Windows Media is either a registered

tr

ademark or trademark of Microsoft

Corporation in the United States and/or

other countries.

This product includes technology owned

by

Microsoft Corporation and cannot be

used or distributed without a license from

Microsoft Licensing, Inc.

iPod & iPhone

iPhone, iPod, iPod classic, iPod nano, and

iP

od touch are trademarks of Apple Inc.,

regi

stered in the U.S. and other countries.

Lightning is a trademark of Apple Inc.

“Made for iPod” and “Made for iPhone”

m

ean that an electronic accessory has

been designed to connect specifically to

iPod or iPhone, respectively, and has been

certified by the developer to meet Apple

performance standards. Apple is not

responsible for the operation of this device

or its compliance with safety and

regulatory standards. Please note that the

use of this accessory with iPod or iPhone

may affect wireless performance.

Android & Google Play

Android, Google Play, and the Google Play

l

ogo are trademarks of Google Inc.

MIXTRAX

MIXTRAX is a trademark of the PIONEER

COR

PORATION.

Spotify®

SPOTIFY and the Spotify logo are among

t

he registered trademarks of Spotify AB.

Compatible mobile digital devices and

premium subscription required, where

available, see https://www.spotify.com.

Russian character chart

Folder

Compressed

audio file

to : Playback sequence

01 to 05: Folder number

D: Display C: Character

Copyright and trademark

General

Power source: 14.4 V DC (10.8 V to 15.1 V

allowable)

Grounding system: Negative type

Maximum current consumption: 10.0 A

Dimensions (W × H × D):

DIN

Chassis: 178 mm × 50 mm × 165 mm

Nose: 188 mm × 58 mm × 17 mm

D

Chassis: 178 mm × 50 mm × 165 mm

Nose: 170 mm × 46 mm × 17 mm

Weight: 1 kg

Audio

Maximum power output:

• 50 W × 4 ch/4 Ω (for no subwoofer)

•

50 W × 2 ch/4 Ω + 70 W × 1 ch/2 Ω

(for subwoofer)

Continuous power output:

22 W × 4 (50 Hz to 15 000 Hz, 5 %

TH

D, 4 Ω load, both channels driven)

Load impedance: 4 Ω (4 Ω to 8 Ω allowable)

Preout maximum output level: 2.0 V

Loudness contour: +10 dB (100 Hz), +6.5

dB

(10 kHz) (volume: –30 dB)

Equalizer (5-Band Graphic Equalizer):

Frequency: 80 Hz/250 Hz/800 Hz/2.5

kHz

/8 kHz

Equalization range: ±12 dB (2 dB step)

Subwoofer (mono):

Frequency: 50 Hz/63 Hz/80 Hz/100

H

z/125 Hz/160 Hz/200 Hz

Slope: –12 dB/oct, –24 dB/oct

Gain: +6 dB to –24 dB

Phase: Normal/Reverse

CD player

System: Compact disc audio system

Usable discs: Compact disc

Signal-to-noise ratio: 94 dB (1 kHz) (IEC-A

ne

twork)

Number of channels: 2 (stereo)

MP3 decoding format: MPEG-1 & 2 Audio

La

yer 3

WMA decoding format: Ver. 7, 7.1, 8, 9, 10,

11, 12

(2 ch audio) (Windows Media

Player)

WAV signal format: Linear PCM & MS

A

DPCM (Non-compressed)

USB

USB standard specification: USB 2.0 full

speed

Maximum current supply: 1.5 A

USB Protocol:

MSC (Mass Storage Class)

MTP (Media Transfer Protocol)

AOA (Android Open Accessory) 2.0

File system: FAT12, FAT16, FAT32

MP3 decoding format: MPEG-1 & 2 Audio

La

yer 3

WMA decoding format: Ver. 7, 7.1, 8, 9, 10,

11, 12

(2 ch audio) (Windows Media

Player)

WAV signal format: Linear PCM & MS

A

DPCM (Non-compressed)

FM tuner

Frequency range: 87.5 MHz to 108.0 MHz

Usable sensitivity: 11 dBf (1.0 μV/75 Ω,

mon

o, S/N: 30 dB)

Signal-to-noise ratio: 72 dB (IEC-A network)

MW tuner

Frequency range: 531 kHz to 1 602 kHz

Usable sensitivity: 25 μV (S/N: 20 dB)

Signal-to-noise ratio: 62 dB (IEC-A network)

LW tuner

Frequency range: 153 kHz to 281 kHz

Usable sensitivity: 28 μV (S/N: 20 dB)

Signal-to-noise ratio: 62 dB (IEC-A network)

NOTE

Specifications and the design are subject

to modifications without notice.

Specifications

2Fr

Avant de commencer ............................................................................. 2

Mise en route ........................................................................................... 3

Radio.......................................................................................................... 5

CD/USB/iPod/AUX................................................................................... 6

Mode d’application................................................................................. 8

Spotify®..................................................................................................... 8

Utilisation de Pioneer ARC APP............................................................ 9

Réglages ................................................................................................. 10

Réglages FUNCTION ............................................................................ 10

Réglages AUDIO.................................................................................... 11

Réglages SYSTEM ................................................................................. 12

Réglages ILLUMINATION..................................................................... 13

Réglages MIXTRAX............................................................................... 13

Raccordements/Installation................................................................ 14

Informations complémentaires.......................................................... 16

À propos de ce mode d’emploi :

• Parmi les instructions suivantes, les clés USB ou les lecteurs audio USB sont

collectivement désignés sous le nom de « périphérique USB ».

• Dans ce mode d’emploi, les iPod et les iPhone sont collectivement désignés sous le

nom d’« iPod ».

Table des matières

Nous vous remercions d’avoir acheté cet appareil PIONEER

Pour garantir une utilisation correcte, lisez bien ce mode d’emploi avant d’utiliser cet appareil. Il est

particulièrement important que vous lisiez et respectiez les indications AT T E N T IO N et PRÉCAUTION

de ce mode d’emploi. Conservez-le dans un endroit sûr et facilement accessible pour toute

consultation ultérieure.

Dans les états membres de l’UE, en Suisse et en Norvège, les foyers domestiques peuvent rapporter

leurs produits électroniques usagés gratuitement à des points de collecte spécifiés ou à un revendeur

(sous réserve d’achat d’un produit similaire).

Dans les pays qui ne sont pas mentionnés ci-dessus, veuillez contacter les autorités locales pour vous

informer de la méthode correcte de mise au rebut.

En agissant ainsi vous assurerez que le produit que vous mettez au rebut est soumis au processus de

traitement, de récupération et de recyclage nécessaire et éviterez ainsi les effets négatifs potentiels sur

l’environnement et la santé publique.

ATTENTION

• N’essayez pas d’installer cet appareil ou d’en faire l’entretien vous-même. L’installation ou

l’entretien de cet appareil par des personnes sans formation et sans expérience en équipement

électronique et en accessoires automobiles peut être dangereux et vous exposer à des risques

d’électrocution ou à d’autres dangers.

• N’essayez pas de démonter ou de modifier cet appareil. Veillez à quitter la route et garer votre véhicule

en lieu sûr avant d’essayer d’utiliser les commandes de l’appareil.

PRÉCAUTION

• Ne laissez pas cet appareil entrer en contact avec de l’humidité et/ou des liquides. Cela pourrait

provoquer une décharge électrique. Tout contact avec des liquides pourrait également provoquer des

dommages, de la fumée et une surchauffe de l’appareil.

• Maintenez le niveau d’écoute à une valeur telle que vous puissiez entendre les sons provenant de

l’extérieur.

• Le Pioneer CarStereo-Pass est utilisable seulement en Allemagne.

• Ce produit est évalué sous des conditions climatiques modérées et tropicales conformément à la

norme CEI 60065 sur les Appareils audio, vidéo et appareils électroniques analogues - Exigences de

sécurité.

Avant de commencer

Si vous souhaitez vous débarrasser de cet appareil, ne le mettez pas à la poubelle avec vos ordures

ménagères. Il existe un système de collecte séparé pour les appareils électroniques usagés, qui

doivent être récupérés, traités et recyclés conformément à la législation.

3Fr

Français

Si vous rencontrez des problèmes

En cas d’anomalie, veuillez contacter votre revendeur ou le centre d’entretien agréé par PIONEER le plus

proche.

DEH-X2900UI

Télécommande en option

La télécommande CD-R320 est vendue séparément.

PRÉCAUTION

Cet appareil est un produit laser de Classe 1, classé selon l’article IEC 60825-1:2007 relatif à la Sécurité

des produits laser.

Mise en route

Fonctionnement de base

Touche de retrait

Fenêtre d’affichage

Molette M.C. (multi-contrôle)

BAND/

DISP (affichage)

SRC (source)/OFF

Port USB

(éjection)

Prise d’entrée AUX (prise stéréo 3,5 mm)

Fente de chargement des disques

Opérations fréquemment utilisées

* Si le fil bleu/blanc de l’appareil est relié à la borne de commande du relais d’antenne automatique du

véhicule, l’antenne se déploie lorsque la source de cet appareil est mise en service. Pour rétracter

l’antenne, mettez la source hors service.

Indication de l’affichage

Retirez la face avant pour empêcher tout vol. Débranchez tous les câbles et les

périphériques branchés à la face avant et mettez l’appareil hors tension avant de le

retirer.

Objectif Opération

Mettre l’appareil sous tension* Appuyez sur SR

C/OFF pour mettre

l’appareil sous tension.

Appuyez longuement sur SRC

/OFF pour

mettre l’appareil hors tension.

Régler le volume Tournez la molette M.

C..

Sélectionner une source Appuyez plusieurs fois sur SR

C/OFF.

Modifier les informations d’affichage Appuyez plusieurs fois sur DI

SP.

Revenir à l’affichage/la liste précédent(e) Appuyez sur BAND/ .

Revenir à l’affichage normal à partir du

menu

Appuyez longuement sur BAND/ .

Indication Description

Apparaît lorsqu’il existe un niveau inférieur de menu ou de dossier.

Apparaît lorsque vous appuyez sur la touche .

Apparaît lorsque la fonction d’accord sur une station locale est en service

(page 10).

Apparaît lorsqu’un programme d’informations routières est capté.

Apparaît lorsque la fonction TA (informations routières) est activée

(page 10).

Apparaît lorsque le sound retriever (correcteur de son compressé) est en

ser

vice (page 11).

Apparaît lorsque la lecture aléatoire est en service.

Apparaît lorsque la lecture répétée est en service.

Apparaît lorsque la fonction de commande d’iPod est en service (page 7).

Retrait de la face avant

4Fr

Important

• Évitez de soumettre la face avant à des chocs excessifs.

• Tenez la face avant à l’abri du soleil et des températures élevées.

• Stockez toujours la face avant détachée, dans un étui de protection ou un sac.

Lorsque vous mettez le contact sur ON après avoir installé l’appareil, [SET UP :YES]

s’affiche.

1 Appuyez sur la molette M.C..

Si vous n’utilisez pas l’appareil dans les 30 secondes qui suivent, le menu de

con

figuration disparaît. Si vous préférez ne pas effectuer la configuration pour

l’instant, tournez la molette M.C. pour sélectionner [NO], puis appuyez pour valider.

2 Tournez la molette M.C. pour sélectionner les options, puis appuyez pour valider.

Pour passer à l’option de menu suivante, vous devez valider votre sélection.

3 [QUIT :YES] apparaît lorsque tous les réglages sont terminés.

Pour revenir au premier élément du menu de configuration, tournez la molette M.

C.

pour sélectionner [QUIT :NO], puis appuyez pour valider.

4 Appuyez sur la molette M.C. pour valider les réglages.

Menu de configuration

Élément de menu Description

LANGUAGE Sélectionnez la langue d’affichage des informations textuelles à

par

tir d’un fichier audio compressé.

[ENG] (anglais),

[РУС

] (russe),

[TU

R] (turc)

CLOCK SET Réglez l’horloge.

FM STEP Sélectionnez l’incrément d’accord FM à partir de 100 kHz ou de

50 kHz.

[100], [50]

Retirer Fixer

REMARQUES

• Vous pouvez annuler le réglage du menu en appuyant sur SRC/OFF.

• Ces paramètres peuvent être ajustés à tout moment à partir des réglages SYSTEM (page 12) et des

réglages INITIAL (page 4).

1 Appuyez sur la molette M.C. pour afficher le menu principal.

2 Tournez la molette M.C. pour sélectionner [SYSTEM], puis appuyez pour valider.

3 Tournez la molette M.C. pour sélectionner [DEMO OFF], puis appuyez pour

valider.

4 Tournez la molette M.C. pour sélectionner [YES], puis appuyez pour valider.

1 Appuyez longuement sur SRC/OFF jusqu’à ce que l’appareil se mette hors

tension.

2 Appuyez longuement sur SRC/OFF pour afficher le menu principal.

3 Tournez la molette M.C. pour sélectionner [INITIAL], puis appuyez pour valider.

4 Tournez la molette M.C. pour sélectionner une option, puis appuyez pour valider.

Annulation de l’affichage de démonstration (DEMO

OFF)

Réglages INITIAL

Élément de menu Description

FM STEP Sélectionnez l’incrément d’accord FM à partir de 100 kHz ou de

50 kHz.

[100], [50]

SP-P/O MODE À sélectionner lorsqu’un haut-parleur à gamme étendue est

r

elié aux fils de sortie du haut-parleur arrière et qu’un haut-

parleur d’extrêmes graves est branché à la sortie RCA.

[REAR/SUB.W]

[SUB.W/SUB.W] À sélectionner lorsqu’un haut-parleur d’extrêmes graves passif

es

t directement relié aux fils de sortie du haut-parleur arrière et

qu’un haut-parleur d’extrêmes graves est branché à la sortie

RCA.

[REAR/REAR] À sélectionner lorsque des haut-parleurs à gamme étendue sont

rel

iés aux fils de sortie du haut-parleur arrière et à la sortie RCA.

Si un haut-parleur à gamme étendue est relié aux fils de sortie

du haut-parleur arrière et que la sortie RCA n’est pas utilisée,

vous pouvez sélectionner [REAR/SUB.W] ou [REAR/REAR].

La page charge ...

Pioneer DEH-X2900UI Manuel utilisateur

Pioneer DEH-X2900UI Manuel utilisateur

dans d''autres langues

Documents connexes