Dremel CKDR-01 Mode d'emploi

Marque: Dremel

Modèle: CKDR-01

Catégorie: Outils électroportatifs

Taper: Mode d'emploi

IMPORTANT: IMPORTANT : IMPORTANTE:

Read Before Using Lire avant usage Leer antes de usar

For English Version Version française Versión en español

See page 2 Voir page 18 Ver la página 34

Operating/Safety Instructions

Consignes de fonctionnement/sécurité

Instrucciones de funcionamiento y seguridad

1-800-4-DREMEL (1-800-437-3635) http://www.dremel.com

Call Toll Free for

Consumer Information

& Service Locations

Pour obtenir des informations

et les adresses de nos centres

de service après-vente,

appelez ce numéro gratuit

Llame gratis para

obtener información

para el consumidor y

ubicaciones de servicio

6300

DM 2610958399 06-09:DM 2610958399 02-09 6/16/09 2:14 PM Page 1

-2-

Work area safety

Keep work area clean and well lit. Cluttered

or dark areas invite accidents.

Do not operate power tools in explosive

atmospheres, such as in the presence of

flammable liquids, gases or dust. Power

tools create sparks which may ignite the dust

or fumes.

Keep children and bystanders away while

operating a power tool. Distractions can

cause you to lose control.

Electrical safety

Power tool plugs must match the outlet.

Never modify the plug in any way. Do not

use any adapter plugs with earthed

(grounded) power tools. Unmodified plugs

and matching outlets will reduce risk of electric

shock.

Avoid body contact with earthed or grounded

surfaces such as pipes, radiators, ranges

and refrigerators. There is an increased risk

of electric shock if your body is earthed or

grounded.

Do not expose power tools to rain or wet

conditions. Water entering a power tool will

increase the risk of electric shock.

Do not abuse the cord. Never use the cord

for carrying, pulling or unplugging the power

tool. Keep cord away from heat, oil, sharp

edges or moving parts. Damaged or entangled

cords increase the risk of electric shock.

When operating a power tool outdoors,

use an extension cord suitable for outdoor

use. Use of a cord suitable for outdoor use

reduces the risk of electric shock.

If operating the power tool in damp locations

is unavoidable use a Ground Fault Circuit

Interrupter (GFCI) protected supply. Use of

a GFCI reduce the risk of electric shock.

GFCI and personal protection devices like

electrician’s rubber gloves and footwear will

further enhance your personal safety.

Do not use AC only rated tools with a DC

power supply. While the tool may appear to

work, the electrical components of the AC

rated tool are likely to fail and create a hazard

to the operator.

Personal safety

Stay alert, watch what you are doing and

use common sense when operating a

power tool. Do not use a power tool while

you are tired or under the influence of drugs,

alcohol or medication. A moment of inattention

while operating power tools may result in

serious personal injury.

Use personal protective equipment. Always

wear eye protection. Protective equipment

such as dust mask, non-skid safety shoes, hard

hat, or hearing protection used for appropriate

conditions will reduce personal injuries.

Prevent unintentional starting. Ensure the

switch is in the off-position before connecting

to power source and / or battery pack,

picking up or carrying the tool. Carrying

power tools with your finger on the switch or

plugging in power tools that have the switch

on invites accidents.

Remove any adjusting key or wrench before

turning the power tool on. A wrench or a

key left attached to a rotating part of the power

tool may result in personal injury.

Do not overreach. Keep proper footing and

balance at all times. This enables better

control of the power tool in unexpected

situations.

Dress properly. Do not wear loose clothing

or jewelry. Keep your hair, clothing and

gloves away from moving parts. Loose

clothes, jewelry or long hair can be caught in

moving parts.

If devices are provided for the connection

of dust extraction and collection facilities,

ensure these are connected and properly

used. Use of dust collection can reduce dust-

related hazards.

Read all safety warnings and instructions. Failure to follow the warnings

and instructions may result in electric shock, fire and/or serious injury.

SAVE ALL WARNINGS AND INSTRUCTIONS

FOR FUTURE REFERENCE

The term “power tool” in all of the warnings listed below refers to your mains-operated

(corded) power tool or battery-operated (cordless) power tool.

WARNING

General Power Tool Safety Warnings

DM 2610958399 06-09:DM 2610958399 02-09 6/16/09 2:14 PM Page 2

-3-

Keep handles dry, clean and free from oil

and grease. Slippery hands cannot safely

control the power tool.

Power tool use and care

Do not force the power tool. Use the correct

power tool for your application. The correct

power tool will do the job better and safer at

the rate for which it was designed.

Do not use the power tool if the switch does

not turn it on and off. Any power tool that

cannot be controlled with the switch is

dangerous and must be repaired.

Disconnect the plug from the power source

and/or the battery pack from the power tool

before making any adjustments, changing

accessories, or storing power tools. Such

preventive safety measures reduce the risk of

starting the power tool accidentally.

Store idle power tools out of the reach of

children and do not allow persons unfamiliar

with the power tool or these instructions to

operate the power tool. Power tools are

dangerous in the hands of untrained users.

Maintain power tools. Check for misalignment

or binding of moving parts, breakage of

parts and any other condition that may

affect the power tools operation. If damaged,

have the power tool repaired before use.

Many accidents are caused by poorly

maintained power tools.

Keep cutting tools sharp and clean. Properly

maintained cutting tools with sharp cutting

edges are less likely to bind and are easier to

control.

Use the power tool, accessories and tool

bits etc. in accordance with these instructions,

taking into account the working conditions

and the work to be performed. Use of the

power tool for operations different from those

intended could result in a hazardous situation.

Use clamps or other practical way to secure

and support the workpiece to a stable

platform. Holding the work by hand or against

your body is unstable and may lead to loss of

control.

Service

Have your power tool serviced by a qualified

repair person using only identical

replacement parts. This will ensure that the

safety of the power tool is maintained.

Develop a periodic maintenance schedule

for your tool. When cleaning a tool be

careful not to disassemble any portion of

the tool since internal wires may be misplaced

or pinched or safety guard return springs

may be improperly mounted. Certain

cleaning agents such as gasoline, carbon

tetrachloride, ammonia, etc. may damage

plastic parts.

Risk of injury to user. The power cord must

only be serviced by a Dremel Service Facility.

SAVE ALL WARNINGS AND INSTRUCTIONS

FOR FUTURE REFERENCE

DM 2610958399 06-09:DM 2610958399 02-09 6/16/09 2:14 PM Page 3

-4-

Hold power tools by insulated gripping

surfaces when performing an operation

where the cutting tools may contact

hidden wiring. Contact with a "live" wire will

make exposed metal parts of the tool "live" and

shock the operator. Do not drill, fasten or break

into existing walls or other blind areas where

electrical wiring may exist. If this situation is

unavoidable, disconnect all fuses or circuit

breakers feeding this worksite.

Use a metal detector to determine if there

are gas or water pipes hidden in the work

area or call the local utility company for

assistance before beginning the operation.

Striking or cutting into a gas line will result in

explosion. Water entering an electrical device

may cause electrocution.

Always hold the tool firmly with both hands

for maximum control. Keep proper footing

and balance at all times. This enables better

control of the power tool in unexpected

situations.

Keep hands away from cutting area. Do

not reach under the material being cut. The

proximity of the blade to your hand is hidden

from your sight.

Do not use dull or damaged blades. Bent

blade can break easily or cause kickback.

Exercise extreme caution when handling

the accessories. The accessories are very

sharp.

Wear protective gloves when changing

cutting accessories. Accessories become

hot after prolonged usage.

Use thick cushioned gloves and limit the

exposure time by taking frequent rest

periods. Vibration caused by the tool may be

harmful to the hands and arms.

Before scraping, check workpiece for nails.

If there are nails, either remove them or set

them well below intended finished surface.

Striking a nail with accessory edge could

cause the tool to jump.

Do not wet sand with this tool. Liquids

entering the motor housing is an electrical

shock hazard.

Never work in area which is soaked with a

liquid, such as a solvent or water, or

dampened such as newly applied

wallpaper. There is an electrical shock

hazard when working in such conditions with a

power tool and heating of the liquid caused by

scraping action may cause harmful vapors to

be emitted from workpiece.

Always wear eye protection and a dust

mask for dusty applications and when

sanding overhead. Sanding particles can

be absorbed by your eyes and inhaled easily

and may cause health complications.

Use special precautions when sanding

chemically pressure treated lumber, paint

that may be lead based, or any other

materials that may contain carcinogens. A

suitable breathing respirator and protective

clothing must be worn by all persons entering

the work area. Work area should be sealed by

plastic sheeting and persons not protected

should be kept out until work area is

thoroughly cleaned.

Do not use sandpaper intended for larger

sanding pads. Larger sandpaper will extend

beyond the sanding pad causing snagging,

tearing of the paper or kick-back. Extra paper

extending beyond the sanding pad can also

cause serious lacerations.

Some dust created by

power sanding, sawing,

grinding, drilling, and other construction

activities contains chemicals known to

cause cancer, birth defects or other

reproductive harm. Some examples of

these chemicals are:

• Lead from lead-based paints,

• Crystalline silica from bricks and cement and

other masonry products, and

• Arsenic and chromium from chemically-

treated lumber.

Your risk from these exposures varies,

depending on how often you do this type of

work. To reduce your exposure to these

chemicals: work in a well ventilated area, and

work with approved safety equipment, such as

those dust masks that are specially designed

to filter out microscopic particles.

WARNING

Safety Rules for Oscillating Tools

DM 2610958399 06-09:DM 2610958399 02-09 6/16/09 2:14 PM Page 4

-5-

IMPORTANT: Some of the following symbols may be used on your tool. Please study them

and learn their meaning. Proper interpretation of these symbols will allow you to operate the

tool better and safer.

Symbol Name Designation/Explanation

V Volts Voltage (potential)

A Amperes Current

Hz Hertz Frequency (cycles per second)

W Watt Power

kg Kilograms Weight

min Minutes Time

s Seconds Time

Diameter Size of drill bits, grinding wheels, etc.

n0No load speed Rotational speed, at no load

.../min Revolutions or reciprocation per minute Revolutions, strokes, surface speed,

orbits etc. per minute

0 Off position Zero speed, zero torque...

1, 2, 3, ... Selector settings Speed, torque or position settings.

I, II, III, Higher number means greater speed

Infinitely variable selector with off Speed is increasing from 0 setting

Arrow Action in the direction of arrow

Alternating current Type or a characteristic of current

Direct current Type or a characteristic of current

Alternating or direct current Type or a characteristic of current

Class II construction Designates Double Insulated

Construction tools.

Earthing terminal Grounding terminal

Warning symbol Alerts user to warning messages

Li-ion RBRC seal Designates Li-ion battery recycling

program

Symbols

This symbol designates

that this tool is listed by

Underwriters Laboratories.

This symbol designates

that this tool is listed by

the Canadian Standards

Association.

This symbol designates that

this tool is listed by the

Canadian Standards

Association, to United States

and Canadian Standards. This symbol

designates

that

this tool

complies

to NOM

Mexican

Standards.

This symbol designates that

this tool is listed by

Underwriters Laboratories, to

United States and Canadian

Standards.

This symbol designates that this tool is listed by the Intertek Testing

Services, to United States and Canadian Standards.

DM 2610958399 06-09:DM 2610958399 02-09 6/16/09 2:14 PM Page 5

-6-

Functional Description and Specifications

Disconnect the plug from the power source before making any

assembly, adjustments or changing accessories. Such preventive safety

measures reduce the risk of starting the tool accidentally.

WARNING

NOTE: For tool specifications refer to the nameplate on your tool.

FIG. 1

Model 6300 Multi-Max Oscillating Power Tool

VARIABLE SPEED

CONTROL DIAL

ON/OFF

SWITCH

POWER

CORD

VENTILATION

OPENINGS

ACCESSORY

CLAMPING

SCREW

ACCESSORY HOLDER

Model number 6300

No load speed n010,000-21,000/min

Voltage rating 120 V 60 Hz

BLADE

WASHER

DM 2610958399 06-09:DM 2610958399 02-09 6/16/09 2:14 PM Page 6

Disconnect the plug from

the power source before

making any assembly, adjustments or

changing accessories. Such preventive

safety measures reduce the risk of starting the

tool accidentally.

For all work or when

changing accessories

always wear protective gloves. Such

preventive safety measures reduce the risk of

injury from sharp edges of the accessories.

Application tools can become very hot while

working. Danger of burns!

INSTALLING AND REMOVING

ACCESSORIES

Dremel cutting, scraper blades have a Quick-

Fit slot which allows for faster accessory

removal compared with other conventional

oscillating tool systems.

1. Loosen the clamping screw using the hex

key provided just enough so you can slide

the accessory between the accessory

holder and the blade washer (Fig. 2).

2. Clean accessory holder, accessory and the

clamping screw with a clean cloth.

3. Place the accessory onto the accessory

holder making sure the accessory engages

all pins in the holder and the accessory is

flush aganist the accessory holder.

4. Securely tighten the clamping screw with

the hex provided (Fig. 3).

NOTE: Some accessories, such as scrapers

or blades, may be mounted either straight on

the tool, or at an angle to enhance usability

(Fig. 4).

INSTALLING AND REMOVING

SANDING SHEETS

Your backing pad uses hook-and-loop backed

accessories, which firmly grip the backing pad

when applied with moderate pressure.

1. Align the sanding sheet and press it onto

the sanding plate by hand.

2. Firmly press the power tool with the

sanding sheet against a flat surface and

briefly switch the power tool on. This will

promote good adhesion and helps to

prevent premature wear.

3. To change, merely peel off the old sanding

sheet, remove dust from the backing pad if

necessary, and press the new sanding

sheet in place.

After considerable service the backing pad

surface will become worn, and the backing pad

must be replaced when it no longer offers a

firm grip. If you are experiencing premature

wear out of the backing pad facing, decrease

the amount of pressure you are applying

during operation of the tool.

For maximum use of abrasive, rotate pad 120

degrees when tip of abrasive becomes worn.

-7-

Assembly

WARNING

FIG. 4

BLADE

WASHER

CLAMPING

SCREW

FIG. 2

FIG. 3

ACCESSORY

HOLDER

HEX

KEY

HEX KEY

CLAMPING

SCREW

WASHER WITH

BEVEL UP

ACCESSORY

DM 2610958399 06-09:DM 2610958399 02-09 6/16/09 2:14 PM Page 7

-8-

Operating Instructions

LEARNING TO USE THE TOOL

Getting the most out of your oscillating tool is a

matter of learning how to let the speed and the

feel of the tool in your hands work for you.

The first step in learning to use the tool is to

get the “feel” of it. Hold it in your hand and feel

its weight and balance (Fig. 5). Depending on

the application, you will need to adjust your

hand position to achieve optimum comfort and

control. The unique comfort grip on the body of

the tool allows for added comfort and control

during use.

When holding tool, do not cover the air vents

with your hand. Blocking the air vents could

cause the motor to overheat.

IMPORTANT! Practice on scrap material first

to see how the tool’s high-speed action

performs. Keep in mind that your tool will

perform best by allowing the speed, along with

the correct accessory, do the work for you. Be

careful not to apply too much pressure.

Instead, lower the oscillating accessory lightly

to the work surface and allow it to touch the

point at which you want to begin. Concentrate

on guiding the tool over the work using very

little pressure from your hand. Allow the

accessory to do the work.

Usually it is better to make a series of passes

with the tool rather than to do the entire job

with one pass. To make a cut, for example,

pass the tool back and forth over the work. Cut

a little material on each pass until you reach

the desired depth.

FIG. 5

Thank you for purchasing the Dremel Multi-

Max.

This tool was designed to tackle home repair,

remodeling and restoration projects. The

Dremel Multi-Max tackles tasks that are

tedious, time consuming or simply next to

impossible to achieve with any other tool.

The ergonomic housing is designed for you

to hold and control in a comfortable manner

during operation.

It comes with an assortment of accessories

that are specifically designed for remodeling

work where you need precision and control.

Your Dremel Multi-Max has a robust electric

motor, is comfortable in the hand, and is

made to accept a large variety of accessories

including flush cut blades, scraper blades,

grout removal wheels and sanding pads.

Accessories come in a variety of shapes and

permit you to do a number of different jobs.

As you become familiar with the range of

accessories and their uses, you will learn just

how versatile your Dremel Multi-Max is.

Visit www.dremel.com to learn more about

what you can do with your Dremel Multi-Max.

INTENDED USE

This Dremel Multi-Max Tool is intended for

dry sanding of surfaces, corners, edges, for

scraping, for sawing soft metals, wood and

plastic components, and for grout removal

using the applicable tools and accessories

recommended by Dremel.

Introduction

DM 2610958399 06-09:DM 2610958399 02-09 6/16/09 2:14 PM Page 8

SLIDE "ON/OFF" SWITCH

The tool is switched "ON" by the slide switch

located on the topside of the motor housing.

TO TURN THE TOOL "ON", slide the switch

button forward.

TO TURN THE TOOL "OFF", slide the switch

button backward.

ELECTRONIC FEEDBACK

Your tool is equipped with an internal

electronic feedback system that provides a

“soft start”, which will reduce the stresses that

occur from a high torque start. The system

also helps to keep the preselected speed

virtually constant between no-load and load

conditions.

VARIABLE SPEED CONTROL DIAL

This tool is equipped with a variable speed

control dial (Fig. 6). The speed may be

controlled during operation by presetting the

dial in any one of ten positions.

OPERATING SPEEDS

The Dremel Multi-Max consists of an AC

universal motor and oscillating mechanism to

perform applications such as cutting, grout

removal, scraping, sanding and more.

The Dremel Multi-Max has a high oscillating

motion of 10,000 - 21,000 /min (OPM). The

high speed motion allows the Dremel Multi-

Max to achieve with excellent results. The

oscillating motion allows the dust to fall to the

surface rather than slinging particles into the

air.

To achieve the best results when working

with different materials, set the variable

speed control to suit the job (See Speed

Chart on Page 10 for guidance) . To select

the right speed for the accessory in use,

practice with scrap material first.

NOTE: Speed is affected by voltages

changes. A reduced incoming voltage will

slow the OPM of the tool, especially at the

lowest setting. If your tool appears to be

running slowly, increase the speed setting

accordingly. The tool may not start at the

lowest switch setting in areas where outlet

voltage is less than 120 volts. Simply move

the speed setting to a higher position to

begin operation.

The variable speed control settings are

marked on the speed control dial. The

settings for approximate /min (OPM) are:

Switch Setting Speed Range

/min (OPM)

2 10,000-11,000

4 11,000-13,000

6 13,000-16,000

8 16,000-19,000

10 19,000-21,000

You can refer to the charts on next page to

determine the proper speed, based on the

material and accessory being used. These

charts enable you to select both the correct

accessory and the optimum speed at a glance.

FIG. 6

-9-

VARIABLE SPEED

CONTROL DIAL

DM 2610958399 06-09:DM 2610958399 02-09 6/16/09 2:14 PM Page 9

-10-

Multi-Max Accessory Speed Settings Use only Dremel, high-performance accessories.



%("*

'((&&

%("*

'("%*

&&

#+)!+*#

&&

#+)!+*#

"&&*#

#+)!+*#

#*

-#

(&+*$&,#

#

(&+*$&,#

#

" "('(#

#."#('(

#

("*"$&%

'(



















































  











"









 

!















 











 























WOOD

1/4

3/4

1/2

WOOD

"

DM 2610958399 06-09:DM 2610958399 02-09 6/16/09 2:14 PM Page 10

-11-

APPLICATION

Your Dremel Multi-Max Tool is intended for

sanding and cutting wooden materials, plastic,

plaster and non-ferrous metals. It is especially

suitable for working close to edges, in tight

spaces, and for flush cutting. This tool must be

used only with Dremel accessories .

Below are some typical uses for your Dremel

Multi-Max Tool.

For all accessories, work

with the accessory away

from the body. Never position hand near or

directly in front of working area. Always hold

the tool with both hands and wear protective

gloves.

Flush Cutting

Remove excess wood from door jamb, window

sill and/or toekick. Removing excess copper or

PVC pipe.

Removal work

e.g. carpets & backing, old tile adhesives,

caulking on masonry, wood and other

surfaces.

Removal of excess materials

e.g. plaster, mortar splatters, concrete on tiles,

sills.

Preparation of surfaces

e.g. for new floors and tiles.

Detail sanding

e.g. for sanding in extremely tight areas

otherwise difficult to reach and require hand

sanding

CUTTING

Saw blades are ideal for making precise cuts

in tight areas, close to edges or flush to a

surface.

Select a medium to high speed for making

initial plunge, start off at medium speed for

increased control. After making your initial cut,

you can increase speed for faster cutting

ability.

Flush cutting blades are

intended to make precise cuts to

allow for installation of flooring or

wall material. When flush cutting

it is important not to force the tool during the

plunge cut. If you experience a strong vibration

in your hand during the plunge cut, this

indicates that you are applying too much

pressure. Back the tool out and let the speed

of the tool do the work. While keeping the teeth

of the blade in the work surface, move the

back of the tool in a slow sideways motion.

This motion will help expedite the cut.

When making a flush cut it is always a good

idea to have a piece of scrap material (tile or

wood) supporting the blade. If you need to rest

the flush cutting blade on a delicate surface,

you should protect the surface with cardboard

or masking tape.

The flat saw blade is ideal for

making precise cuts in wood,

plaster, drywall material.

Applications include cutting openings in

flooring for venting, repairing damaged

flooring, cutting openings for electrical boxes.

The blade works best on softer woods such as

pine. For harder woods, the blade life will be

limited.

Select a medium to high speed.

The flat saw blade can also be used for

window restoration making glazing easy to

remove. The saw blade can be placed directly

against the edge of the window frame, guiding

the blade through the glazing.

GROUT REMOVAL

Grout removal blades are ideal

for removing damaged or

cracked grout. Grout blades

come in different widths (1/16" and 1/8") to

tackle different grout line widths. Before

selecting a grout blade measure the grout line

width to pick the appropriate blade.

Select a medium to high speed.

To remove the grout, use a back and forth

motion, making several passes along the grout

line. The hardness of the grout will dictate how

many passes are needed. Try and keep the

grout blade aligned with the grout line and be

careful not to apply too much side pressure on

the grout blade during the process. To control

plunge depth use the carbide grit line on the

blade as an indicator. Be careful not to plunge

beyond the carbide grit line to avoid damage to

the backer board material.

The grout blades can handle both sanded and

unsanded grout. If you notice the blade

clogging during the grout removal process, you

can use a brass brush to clean the grit, thus

exposing the grit again.

The grout blade geometry is designed so that

the blade can remove all grout up to the

-11-

Operating Applications

WARNING

DM 2610958399 06-09:DM 2610958399 02-09 6/16/09 2:14 PM Page 11

-12-

surface of a wall or corner. This can be

accomplished by ensuring that the segmented

portion of the blade is facing the wall or corner.

SCRAPING

Scrapers are suitable for removing old coats of

varnish or adhesives, removing bonded

carpeting, e.g. on stairs/steps and other

small/medium size surfaces.

Select low to medium speed.

Rigid scrapers are for large area

removal, and harder materials

such as vinyl flooring, carpeting

and tile adhesives. When

removing strong, tacky adhesives, grease the

scraper blade surface with (petroleum jelly

or silicone grease) to reduce gumming up.

The carpet/vinyl flooring removes easier if

it is scored prior to removal so the scraper

blade can move underneath the flooring

material.

Flexible scrapers are used for

hard to reach areas and softer

material such as caulk.

Mount the scraper blade with the logo side

facing up. With the flexible scraper, make sure

that the screw head does not make contact

with surface during the scraping process (a 30

- 45 degree pitch is recommend). This can be

accomplished by making sure that the tool is at

an angle to the blade. You should be able to

see the blade flex during the scraping process.

If you are removing caulk from a delicate

surface such as a bath tub or tile back splash,

we recommend taping or protecting the

surface that the blade will rest on. Use rubbing

alcohol to clean the surface after the caulk

and/or adhesive is removed.

Turn the tool on and place desired accessory

on the area where material is to be removed.

Begin with light pressure. The oscillating

motion of accessory only occurs when

pressure is applied to the material to be

removed.

Excessive pressure can gouge or damage the

background surfaces (e.g,. wood, plaster).

SANDING

Sanding accessories are suitable

for dry sanding of wood, metal,

surfaces, corners and edges and

hard to reach areas.

Work with the complete surface of the sanding

pad, not only with the tip.

Corners may be finished using the tip or edge

of the selected accessory, which should

occasionally be rotated during use to distribute

the wear on the accessory and backing pad

surface.

Sand with a continuous motion and light

pressure. DO NOT apply excessive pressure -

let the tool do the work. Excessive pressure

will result in poor handling, vibration, and

unwanted sanding marks and premature wear

on the sanding sheet.

Always be certain that smaller workpieces are

securely fastened to a bench or other support.

Larger panels may be held in place by hand on

a bench or sawhorses.

Open-coat aluminum oxide sanding sheets are

recommended for most wood or metal sanding

applications, as this synthetic material cuts

quickly and wears well. Some applications,

such as metal finishing or cleaning, require

special abrasive pads which are available from

your dealer. For best results, use Dremel

sanding accessories which are of superior

quality and are carefully selected to produce

professional quality results with your oscillating

tool.

The following suggestions may be used as a

general guide for abrasive selection, but the

best results will be obtained by sanding a test

sample of the workpiece first.

Grit Application

Coarse For rough wood or metal

sanding, and rust or old

finish removal.

Medium For general wood or metal

sanding

Fine For final finishing of wood,

metal, plaster and other

surfaces.

With the workpiece firmly secured, turn tool on

as described above. Contact the work with the

tool after the tool has reached its full speed,

and remove it from the work before switching

the tool off. Operating your oscillating tool in

this manner will prolong switch and motor life,

and greatly increase the quality of your work.

Move the oscillating tool in long steady strokes

parallel to the grain using some lateral motion

to overlap the strokes by as much as 75%.

DO NOT apply excessive pressure - let the

tool do the work. Excessive pressure will result

in poor handling, vibration, and unwanted

sanding marks.

DM 2610958399 06-09:DM 2610958399 02-09 6/16/09 2:14 PM Page 12

-13-

Material Application Grit Size

All wooden materials (e.g.,

hardwood, softwood, chipboard,

building board) Metal materials–

Metal materials, fiberglass

and plastics

Paint, varnish, filling compound

and filler

Masonry, stone, cement

and thin set

Selecting Sanding/Grinding Sheets

GRINDING

The diamond paper accessory

allows for the Multi-Max to be used

for grinding away cement, plaster or

thin set. Preparing the surface for tile

replacement is a common application for this

accessory.

The diamond paper needs to be mounted to

the backing pad prior to use.

Select a low to high speed depending on the

material removal rate desired.

Corners may be finished using the tip or edge

of the selected accessory, which should

occasionally be rotated during use to distribute

the wear on the accessory and backing pad

surface.

Grind with a continuous motion and light

pressure. DO NOT apply excessive pressure -

let the tool do the work. Excessive pressure

will result in poor handling, vibration, and

premature wear on the diamond paper sheet.

For coarse-sanding, e.g. of

rough, unplanned beams and

boards

For face sanding and planing

small irregularities

For finish and fine sanding of

wood

For sanding off paint

For sanding primer (e.g., for

removing brush dashes, drops

of paint and paint run)

For final sanding of primers

before coating

For smoothing, shaping and

braking edges

Coarse

Medium

Fine

Coarse

Medium

Fine

Coarse

120

240

120

240

Sand Paper (Dark)

Sand Paper (White)

Diamond Paper

DM 2610958399 06-09:DM 2610958399 02-09 6/16/09 2:14 PM Page 13

-14-

FIG. 8FIG. 7

CORRECT: Sand with a smooth

back and forth motion, allowing the

weight of the tool to do the work.

INCORRECT: Avoid sanding with

only the tip of the pad. Keep as

much sand paper in touch with the

work surface as possible.

CORRECT: Always sand with the

pad and sandpaer flat against the

work surface. Work smoothly in a

back and forth motion.

INCORRECT: Avoid tipping the

pad. Always sand flat.

CORRECT: Always cut with a

smooth back and forth motion.

Never force the blade. Apply light

pressure to guide the tool.

INCORRECT: Do not twist the tool

while cutting.This can cause the

blade to bind.

CORRECT: Make sure flexible

scraper blade flexes enough

INCORRECT: Avoid screw head

touching surface with flexible

scraper blade.

DM 2610958399 06-09:DM 2610958399 02-09 6/16/09 2:14 PM Page 14

-15-

Service

NO USER SERVICEABLE

PARTS INSIDE. Preventive

maintenance performed by un au thorized

personnel may result in misplacing of

internal wires and components which

could cause serious hazard. We

recommend that all tool service be performed

by a Dremel Service Facility.

CARBON BRUSHES

The brushes and commutator in your tool have

been engineered for many hours of

dependable service.To maintain peak

efficiency of the motor, we recommend every

50 - 60 hours the brush es be serviced by a

Dremel Service Facility.

Cleaning

To avoid accidents always

dis connect the tool from

the power supply before cleaning or

performing any main tenance. The tool may

be cleaned most effectively with compressed

dry air. Always wear safety gog gles when

cleaning tools with compressed air.

Ventilation openings and switch levers must

be kept clean and free of foreign matter. Do

not at tempt to clean by inserting pointed

objects through openings.

Certain cleaning agents

and sol vents damage

plastic parts. Some of these are: gasoline,

carbon tetrachlo ride, chlo rinated cleaning

solvents, ammonia and house hold

detergents that contain ammonia.

WARNING

Maintenance Information

CAUTION

WARNING

If an extension cord is

necessary, a cord with

adequate size conductors that is capable

of carrying the current necessary for your

tool must be used. This will prevent

excessive voltage drop, loss of power or

overheating. Grounded tools must use 3-wire

extension cords that have 3-prong plugs and

receptacles.

NOTE: The smaller the gauge number, the

heav i er the cord.

RECOMMENDED SIZES OF EXTENSION CORDS

120 VOLT ALTERNATING CURRENT TOOLS

WARNING

Extension Cords

Tool’s

Ampere

Rating

Cord Size in A.W.G. Wire Sizes in mm2

3-6

6-8

8-10

10-12

12-16

18 16 16 14 0.75 0.75 1.5 2.5

18 16 14 12 0.75 1.0 2.5 4.0

16 16 14 12 1.0 2.5 4.0 —

14 12 —— ————

25 50 100 150 15 30 60 120

Cord Length in Feet Cord Length in Meters

DM 2610958399 06-09:DM 2610958399 02-09 6/16/09 2:14 PM Page 15

-16-

Accessory

MM11

Base plate for

sanding

MM411

3/8

HCS wood

flush cut blade

MM440

3/4

HCS wood

flush cut blade

MM422

3/4

BIM wood

metal flush cut

blade

MM450

HCS Flat

Saw Blade

MM500 MM501

Segmented

1/8", 1/16" grout

removal

MM600

Rigid scraper

blade

MM610

Flexible scraper

blade

MM900

60 grit diamond

paper

MM70P

Sand paper

MM70W

Sand paper

Material

Depends on sanding

sheet

Wood, plastic,

drywall and other

soft materials

Wood, plastic

drywall and other

soft materials

Non-ferrous metals,

wood, plastic and

other soft metals

Wood (limited use on

hard wood) plastic,

drywall and other

soft materials.

Grout joints

Vinyl, varnish and

carpeting

Caulk, adhesives,

paint and other soft

materials

Thinset, cement

motar and paint.

Varnish and paint

removal

Bare wood,

hardwood, softwood,

chipboard, metal

Application

Sanding surfaces close to edges, in

corners or hard to reach areas.

Depending on the sanding sheet for, e.g.,

sanding wood, paint, varnish, thinset

and cement.

Smaller cuts and flush cuts. Example:

Cut-outs in furniture for cable

connections.

Cutting and deep flush cuts; also for

sawing close to edges, in corners and

hard to reach areas.

Example: Flush cutting door jamb or

window sill, for flooring or tile installation.

Smaller cuts and plunge cuts.

Example: Sawing off water pipes

(copper) or cable ducts flush against

walls, floors or ceilings.

Cutting in existing trim or flooring. Cutting

close to edges in corners or hard to reach

areas. Examples: Installing floor vent or

repairing damaged wood flooring.

Removing grout from between wall or

floor tiles.

Example: Removing grout joints between

wall tiles for repair work.

Remove vinyl flooring and bonded

carpeting. Example: On stairs/steps or

other small/medium sized surfaces.

Scraping off old coats of varnish/paint or

other adhesive.

Removing caulk, coats of peeling paint

or soft adhesive.

Removing thinset or cement; Example:

Grinding away thinset after tile removal.

Removing paint or oil stains from cement.

For sanding primer and removing brush

strokes, drops of paint and paint run.

For detail sanding.

Multi-Max Accessories

HCS = High Carbon Steel BiM =BiMetal

DM 2610958399 06-09:DM 2610958399 02-09 6/16/09 2:14 PM Page 16

-17-

Your Dremel product is warranted against defective material or workmanship for a period of two years from

date of purchase. In the event of a failure of a product to conform to this written warranty, please take the

following action:

1. DO NOT return your product to the place of purchase.

2. Carefully package the product by itself, with no other items, and return it, freight prepaid, along with:

A. A copy of your dated proof of purchase (please keep a copy for yourself).

B. A written statement about the nature of the problem.

C. Your name, address and phone number to:

UNITED STATES

Dremel Service Center Dremel Service Center

4915 21st Street OR 4631 E. Sunny Dunes Road

Racine, WI 53406 Palm Springs, CA 92264

1-800-4-Dremel

CANADA OUTSIDE

Giles Tool Agency CONTINENTAL UNITED STATES

47 Granger Av. See your local distributor or write to

Scarborough, Ont Dremel, 4915 21st Street

Canada M1K 3K9 Racine, WI 53406

1-416-287-3000

We recommend that the package be insured against loss or in transit damage for which we cannot be

responsible.

This warranty applies only to the original registered purchaser. DAMAGE TO THE PRODUCT RESULTING

FROM TAMPERING, ACCIDENT, ABUSE, NEGLIGENCE, UNAUTHORIZED REPAIRS OR ALTERATIONS,

UNAPPROVED ATTACHMENTS OR OTHER CAUSES UNRELATED TO PROBLEMS WITH MATERIAL OR

WORKMANSHIP ARE NOT COVERED BY THIS WARRANTY.

No employee, agent, dealer or other person is authorized to give any warranties on behalf of Dremel. If

Dremel inspection shows that the problem was caused by problems with material or workman ship within the

limitations of the warranty, Dremel will repair or replace the product free of charge and return product

prepaid. Repairs made necessary by normal wear or abuse, or repair for product outside the warranty period,

if they can be made, will be charged at regular factory prices.

DREMEL MAKES NO OTHER WARRANTY OF ANY KIND WHATEVER, EXPRESSED OR IMPLIED, AND ALL

IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE WHICH

EXCEED THE ABOVE MENTIONED OBLIGATION ARE HEREBY DISCLAIMED BY DREMEL AND EXCLUDED

FROM THIS LIMITED WARRANTY.

This warranty gives you specific legal rights and you may also have other rights which vary from state to

state. The obligation of the warrantor is solely to repair or replace the product. The warrantor is not liable for

any incidental or consequential damages due to any such alleged defect. Some states do not allow the

exclusion or limitation of incidental or consequential damages, so the above limitations or exclusion may not

apply to you.

For prices and warranty fulfillment in the continental United States, contact your local Dremel distributor.

Exportado por: Robert Bosch Tool Corporation Mt. Prospect, IL 60056 -2230, E.U.A.

Importado a México por: Robert Bosch, S. de R.L. de C.V.

Calle Robert Bosch No. 405 - 50071 Toluca, Edo. de Méx. - México

Tel. 052 (722) 279 2300 ext 1160 / Fax. 052 (722) 216-6656

Dremel®Limited Warranty

DM 2610958399 06-09:DM 2610958399 02-09 6/16/09 2:14 PM Page 17

-18-

Veuillez lire tous les avertissements et toutes les consignes de sécurité. Si l'on

n'observe pas ces avertissements et ces consignes de sécurité, il existe un risque de

choc électrique, d'incendie et/ou de blessures corporelles graves.

CONSERVEZ TOUS LES AVERTISSEMENTS ET TOUTES LES CONSIGNES

DE SÉCURITÉ POUR RÉFÉRENCE FUTURE.

Dans toutes les mises en garde ci-dessous, le terme « outil électroportatif » se rapporte à des outils branchés

sur le secteur (avec fil) ou à des outils alimentés par piles (sans fil).

Avertissements généraux concernant la sécurité des outils électroportatifs

AVERTISSEMENT

Sécurité du lieu de travail

Maintenez le lieu de travail propre et bien éclairé.

Les risques d’accident sont plus élevés quand on

travaille dans un endroit encombré ou sombre.

N’utilisez pas d’outils électroportatifs dans des

atmosphères explosives, comme par exemple en

présence de gaz, de poussières ou de liquides

inflammables. Les outils électroportatifs produisent

des étincelles qui risquent d’enflammer les poussières

ou les vapeurs.

Éloignez les enfants et les visiteurs quand vous vous

servez d’un outil électroportatif. Vous risquez une

perte de contrôle si on vous distrait.

Sécurité électrique

Les fiches des outils électroportatifs doivent

correspondre à la prise. Il ne faut absolument jamais

modifier la fiche. N’utilisez pas d’adaptateur de prise

avec des outils électroportatifs munis d’une fiche de

terre. Le risque de choc électrique est moindre si on

utilise une fiche non modifiée sur une prise qui lui

correspond.

Évitez tout contact du corps avec des surfaces reliées

à la terre tels que tuyaux, radiateurs, gazinières ou

réfrigérateurs. Le risque de choc électrique augmente

si votre corps est relié à la terre.

N’exposez pas les outils électroportatifs à la pluie ou

à l’humidité. Si de l’eau pénètre dans un outil

électroportatif, le risque de choc électrique augmente.

Ne maltraitez pas le cordon. Ne vous en servez

jamais pour transporter l’outil électroportatif, pour le

tirer ou pour le débrancher. Éloignez le cordon de la

chaleur, des huiles, des arêtes coupantes ou des

pièces mobiles. Les cordons abîmés ou emmêlés

augmentent les risques de choc électrique.

Si vous utilisez un outil électroportatif à l’extérieur,

employez une rallonge conçue pour l’extérieur. Ces

rallonges sont faites pour l’extérieur et réduisent le

risque de choc électrique.

S'il est absolument nécessaire d'utiliser l'outil

électroportatif dans des endroits humides, utilisez

une alimentation protégée par un disjoncteur de fuite

de terre (GFCI). L'utilisation d'un disjoncteur GFCI

réduit les risques de choc électrique.

L’emploi d’un GFCI et de dispositifs de protection

personnelle tels que gants et chaussures d’électricien

en caoutchouc améliorent votre sécurité personnelle.

N’utilisez pas un outil conçu uniquement pour le C.A.

sur une alimentation en C.C. Même si l’outil semble

fonctionner, les composants électriques d’un outil prévu

pour le C.A. tomberont probablement en panne et

risquent de créer un danger pour l’utilisateur.

Sécurité personnelle

Restez concentré, faites attention à ce que vous

faites, et servez-vous de votre bon sens lorsque vous

utilisez un outil électroportatif. N'employez pas

d’outils électroportatifs quand vous êtes fatigué ou

sous l’emprise de drogues, d’alcool ou de

médicaments. Quand on utilise des outils

électroportatifs, il suffit d’un moment d’inattention pour

causer des blessures corporelles graves.

Utilisez des équipements de sécurité personnelle.

Portez toujours une protection oculaire. Le port

d'équipements de sécurité tels que des masques

antipoussières, des chaussures de sécurité

antidérapantes, des casques de chantier et des

protecteurs d'oreilles dans des conditions appropriées

réduira le risque de blessure corporelle.

Évitez les démarrages intempestifs. Assurez-vous que

l'interrupteur est dans la position arrêt (Off) avant de

brancher l'outil dans une prise de courant et/ou un

bloc-piles, de le ramasser ou de le transporter.

Transporter un outil électroportatif avec le doigt sur la

gâchette ou le brancher quand l’interrupteur est en

position “marche” (ON) présente des risques

d’accident.

Enlevez toutes les clés de réglage avant de mettre

l’outil électroportatif en marche. Si on laisse une clé

sur une pièce tournante de l’outil électroportatif, il y a

risque de blessure corporelle.

Ne vous penchez pas. Conservez toujours une bonne

assise et un bon équilibre. Ceci vous permettra de

mieux maîtriser l’outil électroportatif dans des situations

inattendues.

Habillez-vous de manière appropriée. Ne portez pas

de vêtements amples ou de bijoux. Attachez les

cheveux longs. N’approchez pas les cheveux, les

vêtements ou les gants des pièces en mouvement.

DM 2610958399 06-09:DM 2610958399 02-09 6/16/09 2:14 PM Page 18

-19-

Les vêtements amples, les bijoux ou les cheveux longs

risquent d’être happés par les pièces en mouvement.

Si l’outil est muni de dispositifs permettant le

raccordement d’un système d’aspiration et de

collecte des poussières, assurez-vous que ces

dispositifs sont raccordés et utilisés correctement.

L'utilisation d'un dépoussiéreur peut réduire les dangers

associés à l'accumulation de poussière.

Maintenez les poignées sèches et exemptes d’huile et

de graisse. On ne pas maîtriser un outil électroportatif

en toute sécurité quand on a les mains glissantes.

Utilisation et entretien des outils

électroportatifs

Ne forcez pas sur l’outil électroportatif. Utilisez l’outil

électroportatif qui convient à la tâche à effectuer.

L’outil qui convient à la tâche fait un meilleur travail et

est plus sûr à la vitesse pour lequel il a été conçu.

Ne vous servez pas de l’outil électroportatif si son

interrupteur ne parvient pas à le mettre en marche ou

à l’arrêter. Tout outil électroportatif qui ne peut pas

être commandé par son interrupteur est dangereux et

doit être réparé.

Débranchez la fiche de la prise ou enlevez le bloc-pile

de l’outil électroportatif avant tout réglage,

changement d’accessoires ou avant de ranger l’outil

électroportatif. De telles mesures de sécurité

préventive réduisent le risque de démarrage intempestif

de l’outil électroportatif.

Rangez les outils électroportatifs dont vous ne vous

servez pas hors de portée des enfants et ne permettez

pas à des personnes qui ne connaissent pas l’outil

électroportatif ou qui ignorent ces consignes de s’en

servir. Les outils électroportatifs sont dangereux dans

les mains d’utilisateurs inexpérimentés.

Entretenez les outils électroportatifs. Vérifiez que les

pièces mobiles sont alignées correctement et ne

coincent pas. Vérifiez qu’il n’y a pas de pièces

cassées ou d’autre circonstance qui risquent

d’affecter le fonctionnement de l’outil électroportatif.

Si l’outil est abîmé, faites-le réparer avant de

l’utiliser. De nombreux accidents sont causés par des

outils électroportatifs mal entretenus.

Maintenez les outils coupants affûtés et propres. Les

outils coupants entretenus correctement et dotés de

bords tranchants affûtés sont moins susceptibles de

coincer et sont plus faciles à maîtriser.

Utilisez l'outil électroportatif, les accessoires et les

embouts d'outil, etc. conformément à ces instructions,

en tenant compte des conditions de travail et des

travaux à réaliser. L'emploi d’outils électroportatifs

pour des tâches différentes de celles pour lesquelles ils

ont été prévus peut résulter en une situation

dangereuse.

Utilisez des brides ou d’autres moyens pratiques de

brider ou de supporter la pièce sur une plate-forme

stable. Tenir la pièce à la main ou contre le corps est

instable et risque de résulter en une perte de contrôle.

Entretien

Faites réparer votre outil électroportatif par un agent

de service qualifié n’utilisant que des pièces de

rechange identiques. Ceci assure que la sécurité de

l’outil électroportatif est préservée.

Créez un agenda d’entretien périodique pour votre

outil. Quand vous nettoyez un outil, faites attention de

n’en démonter aucune pièce car il est toujours

possible de mal remonter ou de pincer les fils

internes ou de remonter incorrectement les ressorts

de rappel des capots de protection. Certains agents de

nettoyage tels que l’essence, le tétrachlorure de

carbone, l’ammoniaque, etc. risquent d’abîmer les

plastiques.

Risque de blessure pour l'utilisateur. Le cordon

d'alimentation électrique ne doit être réparé que par

des centres de service après-vente agréés de Dremel.

CONSERVEZ TOUS LES AVERTISSEMENTS ET TOUTES LES CONSIGNES

DE SÉCURITÉ POUR RÉFÉRENCE FUTURE.

DM 2610958399 06-09:DM 2610958399 02-09 6/16/09 2:14 PM Page 19

-20-

Consignes de sécurité pour les outils oscillants

Tenez les outils électroportatifs par les surfaces

isolées de préhension en exécutant une opération

au cours de laquelle les outils de coupe peuvent

venir en contact avec les fils cachés. Le contact

avec un fil sous tension rendra les pièces métalliques

exposées de l'outil sous tension et causera des chocs

à l'opérateur. Ne percez, fixez et ne rentrez pas dans

des murs existants ou autres endroits aveugles

pouvant abriter des fils électriques. Si cette situation

est inévitable, débranchez tous les fusibles ou les

disjoncteurs alimentant ce site.

Utilisez un détecteur de métaux afin d’établir s’il y a

des tuyaux d’eau ou à gaz dissimulés dans l’aire de

travail ou appelez la compagnie de service public

locale pour assistance avant de commencer

l’opération. Le fait de frapper une conduite de gaz ou

de couper dans celle-ci provoquera une explosion.

L’eau pénétrant dans un appareil électrique peut

entraîner une électrocution.

Tenez toujours l’outil fermement à deux mains pour

mieux le maîtriser. Conservez toujours une bonne

assise et un bon équilibre. Ceci vous permettra de

mieux maîtriser l’outil électroportatif dans des situations

inattendues.

Tenez les mains à l'écart de l'aire de coupe. Ne

tendez pas la main sous la lame de scie ou à

proximité de celle-ci. La proximité de la lame par

rapport à votre main peut vous être dissimulée.

N'utilisez pas de lames émoussées ou

endommagées. Les lames pliées peuvent aisément se

fracturer ou causer un rebond.

Faites extrêmement attention lorsque vous

manipulez des accessoires. Les accessoires sont

très tranchants.

Portez des gants de protection lorsque vous

changez des accessoires de coupe. Les accessoires

deviennent très chauds après une utilisation

prolongée.

Utilisez des gants épais et rembourrés, et limitez la

durée d'exposition en faisant des pauses fréquentes.

Les vibrations causées par l'outil pourraient être

nuisibles aux mains et aux bras.

Avant de racler, vérifiez l'ouvrage pour y relever des

clous. Si vous relevez des clous, enlevez-les ou

enfoncez-les bien en dessous de la surface finie

recherchée. Le contact du bord de l'accessoire avec

un clou pourrait faire sauter l'outil.

Ne poncez pas par voie humide à l'aide de cette

outil. La pénétration de liquides dans le carter du

moteur constitue un risque de secousses électriques.

Ne travaillez jamais dans un endroit qui est imbibé

de liquide, tel que solvant ou eau, ou humecté tel

qu'un papier peint nouvellement appliqué. Il existe

un danger de secousses électriques en travaillant

dans ces conditions avec un outil électrique, et le

chauffage du liquide causé par le raclage peut faire

dégager des vapeurs nocives du matériau.

Portez toujours des lunettes de protection et un

masque anti-poussières pour les applications

poussiéreuses et lors du ponçage au-dessus de la

tête. Des particules de ponçage peuvent être

absorbées par vos yeux et inhalées facilement et

peuvent causer des problèmes de santé.

Utilisez des précautions spéciales en ponçant le

bois d'oeuvre traité chimiquement par pression, la

peinture pouvant contenir du plomb, ou tout autre

matériau qui peut contenir des agents

cancérigènes. Toutes les personnes pénétrant dans la

zone de travail doivent porter un respirateur et des

vêtements protecteurs adéquats. L'aire de travail doit

être scellée par des feuilles en plastique, et les

personnes non protégées doivent être maintenues à

l'extérieur jusqu'à ce que l'aire de travail soit dûment

nettoyée.

N'utilisez pas du papier de verre destiné à des blocs

de ponçage plus gros. Le papier de verre de

dimensions plus grandes fera saillie au-delà du bloc

de ponçage entraînant ainsi des accrocs, un

déchirement du papier ou un rebond. Le papier

supplémentaire faisant saillie au-delà du bloc de

ponçage peut également causer des lacérations

graves.

Les travaux à la machine

tel que ponçage, sciage,

meulage, perçage et autres travaux du bâtiment

peuvent créer des poussières contenant des produits

chimiques qui sont des causes reconnues de cancer,

de malformation congénitale ou d’autres problèmes

reproductifs. Ces produits chimiques sont, par

exemple :

• Le plomb provenant des peintures à base de plomb,

• Les cristaux de silices provenant des briques et du

ciment et d’autres produits de maçonnerie, et

• L’arsenic et le chrome provenant des bois traités

chimiquement

Le niveau de risque dû à cette exposition varie avec la

fréquence de ces types de travaux. Pour réduire

l’exposition à ces produits chimiques, il faut travailler

dans un lieu bien ventilé et porter un équipement de

sécurité approprié tel que certains masques à poussière

conçus spécialement pour filtrer les particules

microscopiques.

AVERTISSEMENT

DM 2610958399 06-09:DM 2610958399 02-09 6/16/09 2:14 PM Page 20

La page charge ...

Dremel CKDR-01 Mode d'emploi

Marque: Dremel

Modèle: CKDR-01

Catégorie: Outils électroportatifs

Taper: Mode d'emploi

Télécharger le PDF

rapport

dans d''autres langues

English: Dremel CKDR-01 User guide
español: Dremel CKDR-01 Guía del usuario

Documents connexes

Autres documents

Genesis GMT35T Manuel utilisateur