OPERATOR’S MANUAL
MANUEL D’UTILISATION
MANUAL DEL OPERADOR
26CC STRING TRIMMERS
TAILLE-BORDURES À LIGNE 26 CC
RECORTADORAS DE HILO 26 CC
26CS
UT33600
26SS
UT33650
Your string trimmer has been engineered and manufactured to Homelite’s high standard for dependability, ease of operation,
and operator safety. When properly cared for, it will give you years of rugged, trouble-free performance.
WARNING: To reduce the risk of injury, the user must read and understand the operator’s manual before
using this product.
Thank you for buying a Homelite product.
GUARDE ESTE MANUAL PARA
FUTURAS CONSULTAS
CONSERVER CE MANUEL POUR
FUTURE RÉFÉRENCE
To register your Homelite product, please visit:
http://register.homelite.com/
Pour enregistrer votre produit de Homelite, s’il vous
plaît la visite : http://register.homelite.com/
Para registrar su producto de Homelite, por favor visita:
http://register.homelite.com/
Cette taille-bordures à ligne a été conçue et fabriquée conformément
aux strictes normes de fiabilité, simplicité d’emploi et sécurité
d’utilisation de Homelite. Correctement entretenue, elle vous
donnera des années de fonctionnement robuste et sans problème.
AVERTISSEMENT : Pour réduire les risques de
blessures, l’utilisateur doit lire et veiller à bien comprendre le
manuel d’utilisation avant d’employer ce produit.
Merci d’avoir acheté un produit Homelite.
Su recortadora de hilo ha sido diseñada y fabricada de
conformidad con las estrictas normas de Homelite para brindar
fiabilidad, facilidad de uso y seguridad para el operador. Con el
debido cuidado, le brindará muchos años de sólido y eficiente
funcionamiento.
ADVERTENCIA: Para reducir el riesgo de lesiones,
el usuario debe leer y comprender el manual del operador antes
de usar este producto.
Le agradecemos la compra de un producto Homelite.
SAVE THIS MANUAL FOR FUTURE REFERENCE
NOTICE AVIS AVISO
Do not use E15 or E85 fuel in this product. It is a violation of federal law and will damage the unit and
void your warranty. Only use unleaded gasoline containing up to 10% ethanol.
Ne pas utiliser d’essence E15 ou E85 dans ce produit. Une telle utilisation représente une violation
de la loi fédérale et endommagera l’appareil et annulera la garantie. Utiliser seulement de l’essence sans plomb ne contenant
pas plus de 10 % d’éthanol.
No utilice combustibles E15 o E85 con este producto. Esto constituye una violación a la ley federal, dañará la unidad y anulará
la garantía. Use únicamente gasolina sin plomo con un contenido de hasta 10 % de etanol.
ii
See this fold-out section for all of the figures
referenced in the operator’s manual.
Consulter l’encart à volets afin d’examiner
toutes les figures mentionnées dans le manuel
d’utilisation.
Consulte esta sección desplegable para ver todas
las figuras a las que se hace referencia en el
manual del operador.
iii
A - REEL-EASY
™
tap advance string head (avance de la ligne de coupe à tapant
REEL-EASY
™
, sistema de avance de hilo por golpe REEL-EASY
™
)
B - Trimmer shaft (arbre du taille-bordures, eje de la recortadora)
C - Front handle (poignée avant, mango delantero)
D - Power head shaft (arbre du bloc moteur, eje del cabezal motor)
E - Starter grip and rope (poignée du lanceur et corde, mango del arrancador y cuerda)
F - Muffler (silencieux, silenciador)
G - Stop switch (commutateur d’arrêt, interruptor del apagado)
H - Primer bulb (poire d’amorçage, bomba de cebado)
I - Fuel cap (bouchon de carburant, tapa del tanque)
J - Choke lever (levier de volet de départ, palanca de arranque)
K - Throttle trigger (gâchette d’accélérateur, gatillo del acelerador)
L - Curved shaft grass deflector (déflecteur d’herbe d’arbre courbe, deflector de pasto del eje curvo)
M- Straight shaft grass deflector (déflecteur d’herbe d’arbre droit, deflector de pasto para eje recto)
N - Hex key (not shown) (clé hexagonale [non illustré], llave hexagonal [no se muestra])
Fig. 1
26CS
A
B
B
C
A
C
D
D
H
H
G
G
J
J
I
I
L
M
Fig. 2
A - Front handle (poignée avant,
mango delantero)
B - Wing nut (écrou à oreilles, tuerca
de mariposa)
C - Bolt (boulon, perno)
A
B
C
A - Wing nut (écrou à oreilles, tuerca de
mariposa)
B - Bolt (boulon, perno)
C - Grass deflector (déflecteur d’herbe, deflector
de pasto)
D - Bracket (support, soporte)
Fig. 3
A
B
C
26SS
E
F
F
E
D
K
K
A - Gear head (carter d’engrenages, cabezal de
engranajes)
B - Slot (fente, ranura)
C - Wing nut (écrou à oreilles, tuerca de
mariposa)
D - Mounting bracket (support de montage,
soporte de montaje)
E - Trimmer shaft (arbre du taille-bordures, eje
de la recortadora)
F - Grass deflector (déflecteur d’herbe, deflector
de pasto)
Fig. 4
A
C
D
E
F
B
iv
RUN
START
A
A - Throttle trigger (gâchette d’accélérateur,
gatillo del acelerador)
B - Starter grip and rope (poignée du lanceur et
corde, mango del arrancador y cuerda)
C - Stop switch (commutateur d’arrêt, interruptor
del apagado)
D - Primer bulb (poire d’amorçage, bomba de
cebado)
E - Choke lever (levier de volet de départ,
palanca de arranque)
Fig. 7
PROPER OPERATING
POSITION
BONNE POSITION
DE TRAVAIL
POSICIÓN
CORRECTA PARA
EL MANEJO DE LA
HERRAMIENTA
26CS
26SS
Fig. 8
Fig. 9
A - Curved shaft trimmer (taille-bordures à
arbre courbe, recortadora de eje curvo)
B - Dangerous cutting area (zone de coupe
dangereuse, área peligrosa de corte)
C - Best cutting area (zone d’efficacité
maximum, mejor área de corte)
D - Direction of rotation (sens de rotation,
sentido de rotación)
B
A
D
C
A - Trimmer shaft (arbre du taille-bordures,
eje de la recortadora)
B - Power head shaft (arbre du bloc moteur,
eje del cabezal motor)
C - Hex head screws (boulons à six pans,
tornillos de cabeza hexagonal)
D - Indentations (indentations, muescas)
E - Hex key (clé hexagonale, llave hexagonal)
F - Tighten (serrer, ajustar)
G - Loosen (desserrer, aflojar)
A
B
C
E
D
F
G
A - Start position (position de volet de départ
ouvert, posición de arranque)
B - Run position (position de marche, posición
de marcha)
C - Choke lever (levier de volet de départ,
palanca de arranque)
C
Fig. 5
Fig. 6
D
A
B
C
E
C
A
B
A
A - Straight shaft trimmer (taille-bordures à
arbre droit, recortadora de eje recto)
B - Dangerous cutting area (zone de coupe
dangereuse, área peligrosa de corte)
C - Best cutting area (zone d’efficacité
maximum, mejor área de corte)
D - Direction of rotation (sens de rotation,
sentido de rotación)
B
A
C
D
RUN
START
A
v
Fig. 13
Fig. 14
A - Idle speed screw (vis de ralenti, tornillo de
ajuste de la velocidad en vacío)
B - Air filter cover (couvercle du filtre à air, tapa
del filtro de aire)
A
B
Fig. 11
Fig. 12
A - Straight shaft trimmer line cut-off blade
(lame de sectionnement de ligne du taille-
bordures à arbre droit, cuchilla de corte de
hilo de la recortadora de eje recto)
B - Curved shaft trimmer line cut-off blade
(lame de sectionnement de ligne du taille-
bordures à arbre courbe, cuchilla de corte
de hilo de la recortadora de eje recto)
Fig. 10
B
A
Fig. 16
C
A - Latch (loquet, pestillo)
B - Air filter cover (couvercle du filtre à air, tapa
del filtro de aire)
C - Slots (fentes, ranuras)
B
C
A - Latches (loquets, pestillos)
B - Air filter (filtre à air, filtro de aire)
C - Air filter cover (couvercle du filtre à air, tapa
del filtro de aire)
D - Slots (fentes, ranuras)
A
A
D
D
Fig. 15
A
B
A - Eyelet (œillet, ojillo)
B - Arrows (flèches, flechas)
C - Pull strings (tirer vers l’extérieur, tira del
hilo)
D - Rotate the bump knob (tourner le capuchon
du mécanisme de coup dans le sens horaire,
gire a la derecha el perilla percusiva)
B
A
D
C
A - String head housing (boîtier de tête de
coupe, alojamiento del cabezal de hilo)
B - Depress tabs (appuyer sur les languettes,
presione los orejetas)
B
B
A
A - Upper string head housing (boîtier
supérieure de tête de coupe, alojamiento
superior del cabezal de hilo)
B - Tabs (languettes, lengüetas)
C - Lower string head housing (boîtier inférieur
de tête de coupe, alojamiento del cabezal de
hilo)
D - Spool (bobine, carrete)
E - Bump knob (capuchon du mécanisme de
coup, perilla percusiva)
F - Spool slots (fentes de bobine, ranuras de
carrete)
G - Knob ribs (côte de bouton, costillas de la
perilla)
B
A
D
F
G
E
Page / Página 2
Introduction ......................................................................................................................................................................2
Introduction / Introducción
General Safety Rules .....................................................................................................................................................3-4
Règles de sécurité générales / Reglas de seguridad generales
Specific Safety Rules ........................................................................................................................................................ 4
Règles de sécurité particulières / Reglas de seguridad específicas
Symbols ............................................................................................................................................................................ 5
Symboles / Símbolos
Features ............................................................................................................................................................................6
Caractéristiques / Características
Assembly .......................................................................................................................................................................6-7
Assemblage / Armado
Operation ..................................................................................................................................................................... 8-10
Utilisation / Funcionamiento ............................................................................................................................................................ 7-10
Maintenance ..............................................................................................................................................................10-12
Entretien / Mantenimiento .................................................................................................................................................. 10-12 / 10-13
Troubleshooting .............................................................................................................................................................. 13
Dépannage / Corrección de problema......................................................................................................................................... 13 / 14
Warranty ......................................................................................................................................................................... 14
Garantie / Garantía ....................................................................................................................................................................... 14 / 15
Parts Ordering and Service ...............................................................................................................................Back Page
Commande de pièces et réparation / Pedidos de piezas y servicio................................................. Page arrière / Pág. posterio
TABLE OF CONTENTS
TABLE DES MATIÈRES / ÍNDICE DE CONTENIDO
This product has many features for making its use more pleasant and enjoyable. Safety, performance, and dependability
have been given top priority in the design of this product making it easy to maintain and operate.
* * *
Ce produit offre de nombreuses fonctions destinées à rendre son utilisation plus plaisante et satisfaisante. Lors de la
conception de ce produit, l’accent a été mis sur la sécurité, les performances et la fiabilité, afin d’en faire un outil facile à
utiliser et à entretenir.
* * *
Este producto ofrece numerosas características para hacer más agradable y placentero su uso. En el diseño de este producto
se ha conferido prioridad a la seguridad, el desempeño y la fiabilidad, por lo cual se facilita su manejo y mantenimiento.
INTRODUCTION
INTRODUCTION / INTRODUCCIÓN
Page 3 — English
GENERAL SAFETY RULES
WARNING:
READ AND UNDERSTAND ALL INSTRUCTIONS.
Failure to follow all instructions listed below may result
in electric shock, fire and/or carbon monoxide poisoning
which will cause death or serious personal injury.
READ ALL INSTRUCTIONS
For safe operation, read and understand all instructions
before using this product. Follow all safety instructions.
Failure to follow all safety instructions listed below, can
result in serious personal injury.
Do not allow children or untrained individuals to use this
unit.
Do not start or operate the engine in a confined space,
building, near open windows, or in other unventilated
space where dangerous carbon monoxide fumes can
collect. Carbon monoxide, a colorless, odorless, and
extremely dangerous gas, can cause unconsciousness
or death.
Clear the work area before each use. Remove all objects
such as rocks, broken glass, nails, wire, or string which
can be thrown or become entangled in the cutting line
or blade.
Always wear eye protection with side shields marked to
comply with ANSI Z87.1, along with hearing protection.
Failure to do so could result in objects being thrown into
your eyes and other possible serious injuries.
Wear heavy, long pants, long sleeves, boots, and gloves.
Do not wear loose fitting clothing, short pants, sandals,
or go barefoot. Do not wear jewelry of any kind.
Heavy protective clothing may increase operator fatigue,
which could lead to heat stroke. During weather that is
hot and humid, heavy work should be scheduled for early
morning or late afternoon hours when temperatures are
cooler.
Never operate this unit on the operator’s left side.
Secure long hair above shoulder level to prevent entangle-
ment in moving parts.
Keep all bystanders, children, and pets at least
50 ft. away. Bystanders should be encouraged to wear
eye protection. If you are approached, stop the engine
and cutting attachment. In the case of bladed units, there
is the added risk of injury to bystanders from being struck
with the moving blade in the event of a blade thrust or
other unexpected reaction of the saw.
Do not operate this unit when you are tired, ill, upset, or
under the influence of alcohol, drugs, or medication.
Do not operate in poor lighting.
Keep firm footing and balance. Do not overreach. Over-
reaching can result in loss of balance or exposure to hot
surfaces. Keep cutting attachment below waist.
Do not use on a ladder or unstable support. Stable foot-
ing on a solid surface enables better control of the unit
in unexpected situations.
Keep all parts of your body away from any moving part.
To avoid hot surfaces, never operate the unit with the
bottom of the engine above waist level.
Do not touch area around the muffler or cylinder of the
unit, these parts get hot from operation. Contact with hot
surfaces could result in possible serious personal injury.
Always stop the engine and remove the spark plug wire
before making any adjustments or repairs except for
carburetor adjustments.
Inspect the unit before each use for loose fasteners, fuel
leaks, etc. Replace any damaged parts before use.
Never use blades, flailing devices, wire, or rope on trim-
mer attachment. Never use flailing devices, wire, or rope
on any attachment.
The cutting attachment should never rotate at idle during
normal use. The cutting attachment may rotate at idle
during carburetor adjustments.
It has been reported that vibrations from hand-held tools
may contribute to a condition called Raynaud’s Syndrome
in certain individuals. Symptoms may include tingling,
numbness, and blanching of the fingers, usually apparent
upon exposure to cold. Hereditary factors, exposure to
cold and dampness, diet, smoking, and work practices
are all thought to contribute to the development of these
symptoms. It is presently unknown what, if any, vibrations
or extent of exposure may contribute to the condition.
There are measures that can be taken by the operator to
possibly reduce the effects of vibration:
a) Keep your body warm in cold weather. When operating
the unit wear gloves to keep your hands and wrists
warm. It is reported that cold weather is a major factor
contributing to Raynaud’s Syndrome.
b) After each period of operation, exercise to
increase blood circulation.
c) Take frequent work breaks. Limit the amount of
exposure per day.
d) Keep the product well maintained, fasteners
tightened and worn parts replaced.
If you experience any of the symptoms of this condition,
immediately discontinue use and see your physician about
these symptoms.
Mix and store fuel in a container approved for gasoline.
Mix fuel outdoors where there are no sparks or flames.
Wipe up any fuel spillage. Move 30 ft. away from refueling
site before starting engine. Slowly remove the fuel cap
after stopping engine. Do not smoke when refueling.
Stop the engine and allow to cool before refueling or
storing the unit.
Page 4 — English
Inspect before use. Replace damaged parts. Make sure
fasteners are in place and secure. Check for fuel leaks.
Replace string head if cracked, chipped, or damaged
in any way. Be sure the string head is properly installed
and securely fastened. Failure to do so can cause serious
injury.
Make sure all guards, straps, deflectors, and handles are
properly and securely attached.
Never use blades, flailing devices, wire, or rope. Use only
the manufacturer’s recommended or equivalent replace-
ment line in the cutting head. Do not use any other cutting
attachment. To install any other brand of cutting head to
this string trimmer can result in serious personal injury.
Never operate unit without the grass deflector in place
and in good condition.
Maintain a firm grip on both handles while trimming. Keep
string head below waist level. Never cut with the string
head located over 30 in. or more above the ground.
This product is intended for infrequent use by homeown-
ers and other occasional users for such general applica-
tions as trimming light and heavy vegetation, etc. It is not
intended for prolonged use. Prolonged periods of opera-
tion can cause circulatory problems in the user’s hands
due to vibration. For such use, it may be appropriate to
use a product having an anti-vibration feature.
Save these instructions. Refer to them frequently and use
them to instruct others who may use this tool. If you loan
someone this tool, loan them these instructions also.
SPECIFIC SAFETY RULES
GENERAL SAFETY RULES
Allow the engine to cool; empty the fuel tank into a con-
tainer approved for gasoline and secure the unit from
moving before transporting in a vehicle.
Wear your protective equipment and observe all safety
instructions. Be sure the cutting attachment stops turning
when the engine idles. When the unit is turned off make
sure the cutting attachment has stopped before the unit
is set down.
We recommend taking your equipment to a qualified
service center for repair, as service performed by
inexperienced or unqualified persons may damage the
equipment, create unsafe conditions, injury to user and/
or void your warranty.
Page 5 — English
SYMBOLS
Some of the following symbols may be used on this product. Please study them and learn their meaning for safe
operation of this product.
SYMBOL NAME EXPLANATION
Safety Alert Indicates a potential personal injury hazard.
Read Operator’s Manual
To reduce the risk of injury, user must read and under-
stand operator’s manual before using this product.
Eye and Hearing Protection
Always wear eye protection with side shields marked to
comply with ANSI Z87.1 along with hearing protection
when operating this equipment.
Wear Gloves
Wear non-slip, heavy-duty protective gloves when
handling this equipment.
Wear Safety Footwear
Wear non-slip safety footwear when using this
equipment.
Keep Bystanders Away Keep all bystanders at least 50 ft. away.
Ricochet
Thrown objects can ricochet and result in personal injury
or property damage.
No Blade
Do not install or use any type of blade on a product dis-
playing this symbol.
Hot Surface
To reduce the risk of injury or damage, avoid contact
with any hot surface.
Gasoline and Lubricant
Use unleaded gasoline intended for motor vehicle use
with an octane rating of 87 [(R + M) / 2] or higher. This
product is powered by a 2-cycle engine and requires
pre-mixing gasoline and 2-cycle lubricant.
The following signal words and meanings are intended to explain the levels of risk associated with this product.
SYMBOL SIGNAL MEANING
DANGER:
Indicates a hazardous situation, which, if not avoided, will result in death or
serious injury.
WARNING:
Indicates a hazardous situation, which, if not avoided, could result in death or
serious injury.
CAUTION:
Indicates a hazardous situation, that, if not avoided, may result in minor or
moderate injury.
NOTICE:
(Without Safety Alert Symbol) Indicates information considered important, but
not related to a potential injury (e.g. messages relating to property damage).
Page 6 — English
FEATURES
FEATURES
PRODUCT SPECIFICATIONS
Line Cutting Width
Curved Shaft ............................................................................................................................................................17 in.
Straight Shaft ...........................................................................................................................................................18 in.
Engine Displacement.......................................................................................................................................................26cc
Line Diameter ............................................................................................................................................................0.095 in.
KNOW YOUR STRING TRIMMER
See Figure 1.
The safe use of this product requires an understanding of
the information on the tool and in this operator’s manual as
well as a knowledge of the project you are attempting. Before
use of this product, familiarize yourself with all operating
features and safety rules.
GRASS DEFLECTOR
The trimmer includes a grass deflector that helps protect
you from flying debris.
REEL-EASY
™
TAP ADVANCE SYSTEM
The REEL-EASY
™
Tap Advance System allows easy line
advance during trimmer operation.
TOP-MOUNTED MOTOR
The top-mounted motor improves balance and is located
away from the dust and debris of the cutting area.
ASSEMBLY
UNPACKING
This product requires assembly.
Carefully remove the product and any accessories from
the box. Make sure that all items listed in the packing list
are included.
WARNING:
Do not use this product if any parts on the Packing List
are already assembled to your product when you unpack
it. Parts on this list are not assembled to the product by
the manufacturer and require customer installation. Use
of a product that may have been improperly assembled
could result in serious personal injury.
Inspect the product carefully to make sure no breakage
or damage occurred during shipping.
Do not discard the packing material until you have care-
fully inspected and satisfactorily operated the product.
If any parts are damaged or missing, please call
1-800-242-4672 for assistance.
PACKING LIST
Power Head Shaft
Trimmer Shaft
Front Handle
Hex Key
Curved Shaft Grass Deflector – 26CS
PACKING LIST (continued)
Straight Shaft Grass Deflector – 26SS
Bottle of 2-Cycle Lubricant
Operator’s Manual
WARNING:
If any parts are damaged or missing, do not operate this
product until the parts are replaced. Use of this product
with damaged or missing parts could result in serious
personal injury.
WARNING:
Do not attempt to modify this product or create acces-
sories not recommended for use with this product. Any
such alteration or modification is misuse and could result
in a hazardous condition leading to possible serious
personal injury.
WARNING:
To prevent accidental starting that could cause serious
personal injury, always disconnect the engine spark plug
wire from the spark plug when assembling parts.
Page 7 — English
ASSEMBLY
FRONT HANDLE
See Figure 2.
Loosen and remove the wing nut, washer, and bolt from
the handle.
Install the handle on the power head shaft at the location
indicated by the label on the shaft.
Adjust handle up or down, if necessary, to desired operat-
ing position.
Reinstall the bolt, washer, and wing nut. Tighten wing nut
to secure.
Slightly loosen the wing nut on the handle.
Rotate the handle on the drive shaft housing at the loca-
tion indicated by the label on the shaft.
Retighten the wing nut to secure the handle in place.
ATTACHING THE GRASS DEFLECTOR
WARNING:
The line cutting blade on the grass deflector is sharp.
Avoid contact with the blade. Failure to avoid contact
can result in serious personal injury.
TO ATTACH THE CURVED SHAFT GRASS
DEFLECTOR – 26CS
See Figure 3.
Remove the bolt and wing nut from grass deflector.
Press the grass deflector onto the bottom of the curved
shaft as shown.
Insert the bolt through the grass deflector and the bracket
on the curved shaft.
Place the wing nut on the bolt and tighten securely.
TO ATTACH THE STRAIGHT SHAFT GRASS
DEFLECTOR – 26SS
See Figure 4.
Remove the wing nut and mounting bracket from the grass
deflector.
Assemble straight shaft grass deflector to drive shaft so
that the pin in the grass deflector fits in the locator hole
in the lower side of the drive shaft near the gear head.
Place the mounting bracket over the drive shaft so the
square tab on the mounting bracket fits into the slot in
the straight shaft grass deflector.
Rotate the mounting bracket so the screw on the grass
deflector goes into the slot on the mounting bracket.
Reinstall the wing nut and tighten securely.
CONNECTING THE POWER HEAD SHAFT AND
TRIMMER SHAFT
See Figure 5.
WARNING:
Never install, remove, or adjust any attachment while
power head is running. Failure to stop the engine can
cause serious personal injury.
Align the two indentations in the trimmer shaft with the
screws in the power head shaft. Insert the trimmer shaft
into the power head shaft.
Push the two sections together until the trimmer shaft
stops.
Using a hex key, turn each of the two screws until securely
tightened.
WARNING:
Be certain the shafts are locked into place before oper-
ating string trimmer; check it periodically for tightness
during use to avoid possible disconnection of shafts,
which could result in serious personal injury.
CAUTION:
Be careful when sliding the two shafts together to avoid
pinching your hands or fingers.
WARNING:
This string trimmer is designed to use only the provided
trimmer shaft and string head. It is not capable of using
other attachments or cutting heads. Attempting to use
other attachments or cutting heads could result in seri-
ous personal injury.
Page 8 — English
WARNING:
Do not allow familiarity with this product to make you
careless. Remember that a careless fraction of a second is
sufficient to inflict serious injury.
WARNING:
Always wear eye protection with side shields marked to
comply with ANSI Z87.1, along with hearing protection.
Failure to do so could result in objects being thrown into
your eyes and other possible serious injuries.
WARNING:
Never use blades, flailing devices, wire, or rope on this prod-
uct. Do not use any attachments or accessories not rec-
ommended by the manufacturer of this product. The use of
attachments or accessories not recommended can result
in serious personal injury.
NOTICE:
The spark arrestor on this product has not been evalu-
ated by the USDA Forest Service and cannot be used on
U.S. forest lands. In addition, product users must comply
with Federal, State, and local fire prevention regulations.
Check with appropriate authorities. Contact customer
service or a qualified service center to purchase a re-
placement spark arrestor.
NOTICE:
Before each use, inspect the entire product for damaged,
missing, or loose parts such as screws, nuts, bolts, caps,
etc. Tighten securely all fasteners and caps and do not
operate this product until all missing or damaged parts
are replaced. Please contact customer service or a quali-
fied service center for assistance.
ETHANOL-BLENDED FUELS
NOTICE:
Do not use E15 or E85 fuel in this product. It is a viola-
tion of federal law and will damage the unit and void
your warranty. Only use unleaded gasoline containing
up to 10% ethanol.
NOTE: To improve performance when using oxygenated
fuels, we recommend the use of Ethanol Shield 2-cycle
lubricant.
FUELING AND REFUELING THE TRIMMER
WARNING:
Gasoline and its vapors are highly flammable and ex-
plosive. To prevent serious personal injury and property
damage, handle it with care. Keep away from ignition
sources and open flames, handle outdoors only, do not
smoke and wipe up spills immediately.
FUEL MIXTURE
This product is powered by a 2-cycle engine and requires
pre-mixing gasoline and 2-cycle lubricant. Pre-mix unleaded
gasoline and 2-cycle engine lubricant in a clean container
approved for gasoline. DO NOT mix quantities larger than
usable in a 30-day period.
Recommended fuel: This engine is certified to operate on
unleaded gasoline intended for automotive use.
NOTE: We recommend you use Ethanol Shield 2-cycle
lubricant, Homelite premium 2-cycle lubricant, or an equiv-
alent high-quality synthetic 2-cycle lubricant in this prod-
uct. Mix at 2.6 oz. per gallon (US).
Do not use automotive lubricant or 2-cycle outboard
lubricant.
HIGH QUALITY 2-CYCLE ENGINE LUBRICANT
GASOLINE LUBRICANT
1.0 gal. (US) (3.8 liter) 2.6 oz. (76 ml)
FILLING TANK
Clean surface around fuel cap to prevent contamination.
Loosen fuel cap slowly. Rest the cap on a clean surface.
Carefully pour fuel mixture into the tank. Avoid spillage.
Prior to replacing the fuel cap, clean and inspect the
gasket.
Immediately replace fuel cap and hand tighten. Wipe up
any fuel spillage.
NOTE: It is normal for smoke to be emitted from a new
engine after first use.
WARNING:
Always shut off engine before fueling. Never remove
fuel cap or add fuel to a machine with a running or hot
engine. Make sure the unit is sitting on a flat, level sur-
face and only add fuel outdoors. If the engine is hot, let
the unit cool for at least five minutes before adding fuel.
After fueling, immediately replace fuel cap and tighten
securely. Move at least 30 ft. from refueling site before
starting engine. Do not smoke and stay away from open
flames and sparks! Failure to follow these instructions
could result in a fire and cause serious personal injury.
OPERATION
Page 9 — English
OPERATION
WARNING:
To avoid burns from hot surfaces, never operate unit with
the bottom of the engine above waist level.
Hold the trimmer with your right hand on the rear handle
and your left hand on the front handle. Keep a firm grip with
both hands while in operation. Trimmer should be held at a
comfortable position with the rear handle about hip height.
Always operate trimmer at full throttle. Cut tall grass from the
top down. This will prevent grass from wrapping around the
shaft housing and string head which may cause damage from
overheating. If grass becomes wrapped around the string
head, STOP THE ENGINE, disconnect the spark plug wire,
and remove the grass. Prolonged cutting at partial throttle
will result in lubricant dripping from the muffler.
WARNING:
Always hold the string trimmer away from the body keep-
ing clearance between the body and the product. Any
contact with the housing or string trimmer cutting head
can result in burns and/or other serious personal injury.
CUTTING TIPS
See Figures 8 - 9.
Avoid hot surfaces by always keeping the tool away from
your body. (Proper operating position shown in figure 8.)
Keep the trimmer tilted toward the area being cut; this is
the best cutting area.
The curved shaft trimmer cuts when passing the unit from
right to left. The straight shaft trimmer cuts when passing
the unit from left to right. This will avoid throwing debris at
the operator. Avoid cutting in the dangerous area shown
in figure 9.
Use the tip of line to do the cutting; do not force string
head into uncut grass.
Wire and picket fences cause extra line wear, even break-
age. Stone and brick walls, curbs, and wood may wear
line rapidly.
Avoid trees and shrubs. Tree bark, wood moldings, siding,
and fence posts can easily be damaged by the line.
ADVANCING LINE USING THE REEL-EASY
™
TAP ADVANCE SYSTEM
Line advance is controlled by tapping string head on grass
while running engine at full throttle.
Run engine at full throttle.
Tap string head on ground to advance line. Line advances
each time the head is tapped.
Several taps may be required until line strikes the cut off
blade.
Resume trimming.
STARTING AND STOPPING
See Figures 6 - 7.
Trimmer should be on a flat, bare surface for starting.
To start a cold engine:
Slowly press the primer bulb 10 times.
Set the choke lever to the START (A) position.
Squeeze the throttle trigger fully and pull the starter grip
and rope until the engine runs. Do not pull the starter grip
more than six (6) times.
NOTE: Keep throttle trigger squeezed fully through re-
maining steps. If the engine does not start, start over at
the first step with pressing the primer bulb.
Allow the engine to warm up, then set the choke lever to
the RUN (B) position.
NOTE: There is a detent location between positions A
and B to help ease starting and warm up, if needed.
To restart a warm engine:
Slowly press the primer bulb 10 times.
Set the choke lever to the RUN (B) position.
Squeeze the throttle trigger fully and pull the starter grip
and rope until the engine runs.
To stop the engine:
To stop the engine, depress the STOP switch to the stop
position “ ”.
IF ASSISTANCE IS REQUIRED FOR THIS PRODUCT:
Do not return this product to the retail store where it was
purchased. Please call our Customer Service Department
for any issues you may have.
For Help Call: 1-800-242-4672
OPERATING THE TRIMMER
See Figure 8.
WARNING:
Engine housing can become hot during trimmer opera-
tion. Do not rest or place your arm, hand, or any body
part against the engine housing during trimmer operation.
Only hold the trimmer as shown in Figure 8 with all body
parts clear of engine housing. Extended contact with
the engine housing can result in burns or other injuries.
WARNING:
Always position the unit on the operator’s right side. The
use of the unit on the operator’s left side will expose the
operator to hot surfaces and can result in possible burn
injury.
Page 10 — English
Normal maintenance, replacement or repair of emission con-
trol devices and systems may be performed by any qualified
repair establishment or individual with original or equivalent
parts. Warranty and recall repairs must be performed by a
authorized service center; please contact customer service
for assistance.
WARNING:
Before inspecting, cleaning, or servicing the machine,
shut off engine, wait for all moving parts to stop, and
disconnect spark plug wire and move it away from spark
plug. Failure to follow these instructions can result in
serious personal injury or property damage.
WARNING:
Always wear eye protection with side shields marked to
comply with ANSI Z87.1, along with hearing protection.
Failure to do so could result in objects being thrown into
your eyes and other possible serious injuries.
WARNING:
When servicing, use only recommended or equivalent
replacement parts. Use of any other parts could create
a hazard or cause product damage.
NOTICE:
Periodically inspect the entire product for damaged,
missing, or loose parts such as screws, nuts, bolts, caps,
etc. Tighten securely all fasteners and caps and do not
operate this product until all missing or damaged parts
are replaced. Please contact customer service or a quali-
fied service center for assistance.
OPERATION
NOTE: The line trimming cut-off blade on the grass deflector
will cut the line to the correct length.
NOTE: If the line is worn too short you may not be able to
advance the line by tapping it on the ground. If so, STOP
THE ENGINE, disconnect the spark plug wire, and manually
advance the line.
ADVANCING THE LINE MANUALLY
With the engine off and the spark plug wire disconnected,
push the spool retainer down while pulling on line(s) to manu-
ally advance the line.
GRASS DEFLECTOR LINE TRIMMING CUT-OFF
BLADE
See Figure 10.
The trimmer is equipped with a line trimming cut-off blade on
the grass deflector. For best cutting, advance line until it is
trimmed to length by the cut-off blade. Advance the line when-
ever you hear the engine running faster than normal, or when
trimming efficiency diminishes. This will maintain best perfor-
mance and keep the line long enough to advance properly.
MAINTENANCE
GENERAL MAINTENANCE
Avoid using solvents when cleaning plastic parts. Most
plastics are susceptible to damage from various types of
commercial solvents and may be damaged by their use.
Use clean cloths to remove dirt, dust, lubricant, grease, etc.
WARNING:
Do not at any time let brake fluids, gasoline, petroleum-
based products, penetrating lubricants, etc., come in con-
tact with plastic parts. Chemicals can damage, weaken or
destroy plastic which could result in serious personal injury.
LINE REPLACEMENT
See Figures 11.
Use only .095 in. trimmer line. Use original manufacturer’s
replacement line for best performance.
Stop the engine and disconnect the spark plug wire.
Rotate the bump knob clockwise as necessary to align
the arrows on the bump knob with the eyelets in the string
head housing.
Cut one piece of trimmer line 18 ft. long. Insert the line
into the eyelet on the string head housing. Push until the
end of the line comes out the other side of the housing.
Pull the line until equal amounts of line appear on both
sides of the housing.
NOTE: Line may jam if more than 18 ft. is loaded.
Rotate the bump knob clockwise to wind the line on the
spool until approximately 6 in. of line is showing on each
side.
Push the bump knob down while pulling on line(s) to
manually advance the line.
Page 11 — English
CLEARING LINE JAM AND/OR REPLACING
BUMP KNOB
See Figures 12 - 13.
Stop the engine and disconnect the spark plug wire.
Depress the tabs on the side of the string head housing
to remove the lower string head housing.
NOTE: The housing is spring loaded and will self eject
when the tabs are depressed. It is not necessary to re-
move the upper string head housing from the drive shaft.
Push the spool and bump knob through the string head
housing and remove the string from the spool.
If replacing the bump knob, remove the old knob from
the spool. Align the knob ribs with the spool slots and
place the new bump knob onto the spool. If you are not
replacing the bump knob, skip this step.
Insert the bump knob and spool assembly through the
opening in the string head housing.
Align the slots on the lower string head housing with the
tabs on the upper string head housing.
Push the housing together until the tabs snap into place.
NOTE: Hold the spool by the knob while completing the
installation.
Install line as described in Line Replacement.
CLEANING THE EXHAUST PORT, MUFFLER,
AND SPARK ARRESTOR
NOTICE:
The spark arrestor on this product has not been evalu-
ated by the USDA Forest Service and cannot be used on
U.S. forest lands. In addition, product users must comply
with Federal, State, and local fire prevention regulations.
Check with appropriate authorities. Contact customer
service or a qualified service center to purchase a re-
placement spark arrestor.
NOTE: Depending on the type of fuel used, the type and
amount of lubricant used, and/or your operating conditions, the
exhaust port, muffler, and/or spark arrestor screen may be-
come blocked with carbon deposits. If you notice a power
loss with your gas powered tool, you may need to remove
these deposits to restore performance. We highly recommend
that only qualified service technicians perform this service.
The spark arrestor must be cleaned or replaced every 50
hours or yearly to ensure proper performance of your prod-
uct. Spark arrestors may be in different locations depending
on the model purchased. Please contact your nearest service
dealer for the location of the spark arrestor for your model.
IDLE SPEED ADJUSTMENT
See Figure 14.
WARNING:
The cutting head will move when adjusting the idle speed.
Wear all protective clothing and keep all bystanders,
children, and pets at least 50 ft. away. Make adjustments
with the unit supported by hand so that the cutting head
does not contact the ground or any object. Keep all parts
of your body away from the cutting head and muffler.
Failure to follow these instructions could result in serious
personal injury.
If the cutting attachment turns at idle, the idle speed screw
needs adjusting on the engine. Turn the idle speed screw
counterclockwise to reduce the idle RPM and stop the cut-
ting attachment movement. If the cutting attachment still
moves at idle speed, contact a service dealer for adjustment
and discontinue use until the repair is made.
WARNING:
The cutting attachment should never turn at idle. Turn
the idle speed screw counterclockwise to reduce the
idle RPM and stop the cutting attachment, or contact a
service dealer for adjustment and discontinue use until
the repair is made. Serious personal injury could result
from the cutting attachment turning at idle.
CLEANING THE AIR FILTER
See Figures 15 - 16.
For proper performance and long life, keep air filter clean.
Remove the air filter cover by pushing down on the latches
while gently pulling off the cover.
Remove the air filter.
Clean the foam filter element with warm soapy water.
Rinse and let dry.
NOTE: If the foam filter element is damaged, it should be
replaced.
Apply a light coat of engine oil to the foam filter element,
then squeeze it out.
Reinstall the air filter.
NOTE: Make sure the filter is seated properly inside the
cover. Installing the filter incorrectly will allow dirt to enter
the engine, causing rapid engine wear.
Replace the air filter cover by placing the slots on the air
filter cover over the latches on the housing, then push
the cover down until it snaps securely in place.
MAINTENANCE
Page 12 — English
MAINTENANCE
FUEL CAP, TANK, AND LINES
WARNING:
Check for fuel leaks. A leaking fuel cap, tank, or lines
are a fire hazard and must be replaced immediately. If
you find any leaks, correct the problem before using the
product. Failure to do so could result in a fire that could
cause serious personal injury.
The fuel cap contains a non-serviceable filter and a check
valve. A clogged fuel filter will cause poor engine perfor-
mance. If performance improves when the fuel cap is loos-
ened, check valve may be faulty or filter clogged. Replace
fuel cap if required.
SPARK PLUG REPLACEMENT
This engine uses a Champion RCJ-6Y, Torch L7RTC, or
equivalent spark plug with .025 in. electrode gap. Use a rec-
ommended or equivalent replacement and replace annually.
NOTICE:
Be careful not to cross-thread the spark plug. Cross-
threading will seriously damage the product.
STORING THE PRODUCT
Clean all foreign material from the product. Store idle unit
indoors in a dry, well-ventilated area that is inaccessible
to children. Keep away from corrosive agents such as
garden chemicals and de-icing salts.
Abide by all ISO and local regulations for the safe storage
and handling of gasoline.
When storing 1 month or longer:
Drain all fuel from tank into a container approved for
gasoline. Run engine until it stops.
HIGH ALTITUDE ENGINE OPERATION
Your engine is configured for operation below 2000 feet
altitude at the factory. Your engine must be re-configured
for operation above 2000 feet altitude. Operating the engine
with the wrong engine configuration at a given altitude may
increase its emissions, decrease fuel efficiency, degrade per-
formance and cause irreversible damage. Engines configured
for high altitude operation cannot be operated in standard
altitude conditions. A qualified service center should ensure
that your engine is properly configured for your location.
THIS PRODUCT WAS MANUFACTURED WITH A CATALYST MUFFLER
Congratulations! You have made an investment toward protecting the environment. In order to maintain this product’s
original emission level, please refer to the maintenance section below.
MAINTENANCE SCHEDULE
Inspect For Clean Replace Replace
Maintenance Damage Before Every Every 25 Hours Every
Part Each Use 5 Hours or Yearly 50 Hours
* CATALYTIC MUFFLER ASSEMBLY..................................................................................................................X
SPARK SCREEN ...............................................................................................................................................X
* AIR FILTER ASSY
includes:
Filter Screen ........................................................................ X
* CARBURETOR ASSY
includes:
Gaskets ........................................ X
* FUEL TANK ASSY
includes:
Fuel Lines ..................................... X
Fuel Cap ....................................... X
Fuel Filter................................................................................................................... X
* IGNITION ASSY
includes:
Spark Plug ................................................................................................................. X
* NOTICE: THE USE OF EMISSION CONTROL COMPONENTS OTHER THAN THOSE DESIGNED FOR THIS UNIT
IS A VIOLATION OF FEDERAL LAW.
Page 13 — English
TROUBLESHOOTING
PROBLEM POSSIBLE CAUSE SOLUTION
1. Clean or replace spark plug. Reset spark plug gap.
Refer to Spark Plug Replacement earlier in this
manual.
2. Push primer bulb until bulb is full of fuel. If bulb does
not fill, primary fuel delivery system is blocked.
Contact a qualified service center. If primer bulb
fills, engine may be flooded, proceed to next item.
3. Set the choke lever to the START position. Squeeze
the trigger and pull the starter grip and rope
repeatedly until the engine starts and runs.
NOTE: Depending on the severity of the flooding,
this may require numerous pulls of the starter grip
and rope.
1. Use fresh fuel and the correct 2-cycle lubricant mix.
(50:1).
2. Clean air filter screen. Refer to Cleaning Air Filter
earlier in this manual.
3. Contact a qualified service center.
4. Clean or replace spark plug. Reset spark plug gap.
Refer to Spark Plug Replacement earlier in this
manual.
1. Turn idle speed screw clockwise to increase idle
speed. See Figure 15.
1. Lubricate line with silicone spray.
2. Install more line. Refer to the applicable line re-
placement section in this manual.
3. Pull lines while alternately pressing down on and
releasing spool retainer.
4. Remove line from spool and rewind. Refer to the
applicable line replacement section in this manual.
5. Advance line at full throttle.
Engine will not start
Engine does not reach full
speed and emits excessive
smoke
Engine starts, runs, and ac-
celerates but will not idle
Line will not advance
1. No spark.
2. No fuel.
3. Engine is flooded.
1. Incorrect lubricant/fuel mixture.
2. Air filter is dirty.
3. Spark arrestor screen is dirty.
4. Spark plug fouled.
1. Idle speed screw on carburetor
needs adjustment.
1. Line is welded to itself.
2. Not enough line on spool.
3. Line is worn too short.
4. Line is tangled on spool.
5. Engine speed is too slow.
1. Clean threads and lubricate with grease - if no
improvement, replace the spool retainer.
1. Cut tall grass from the top down to prevent
wrapping.
2. Operate trimmer at full throttle.
1. Reassemble shafts. Refer to Connecting the
Power Head Shaft and Trimmer Shaft in the
Assembly section of this manual.
Spool retainer hard to turn
Grass wraps around drive
shaft housing and string head
Engine starts and runs but
string head does not turn
1. Screw threads are dirty or damaged.
1. Cutting tall grass at ground level.
2. Operating trimmer at part throttle.
1. Shafts are incorrectly assembled.
If problem persists after trying the above solutions, contact customer service or a qualified service center for assistance.
NOTICE:
As the equipment owner, you are responsible for the performance of the required maintenance listed in the Maintenance
section. It is recommended that you retain all receipts covering maintenance on your equipment. Neglecting or failing to
perform the required maintenance may increase emissions, decrease fuel efficiency, degrade performance, cause irrevers-
ible engine damage and/or void your warranty.
Page 14 — English
WARRANTY
LIMITED WARRANTY STATEMENT
Homelite Consumer Products, Inc., (“Homelite”) warrants
to the original retail purchaser that this HOMELITE brand
outdoor product is free from defect in material and
workmanship and agrees to repair or replace, at Homelite’s
discretion, any defective product free of charge within these
time periods from the date of purchase.
Two years for all models if used for personal, family, or
household use;
90 days for any unit used for other purposes, such as
rental or commercial.
This warranty extends to the original retail purchaser only
and commences on the date of the original retail purchase.
Any part of the this product manufactured or supplied
by Homelite and found in the reasonable judgment of
Homelite to be defective in material or workmanship will
be repaired or replaced without charge for parts and labor
by a Homelite authorized service center.
The product, including any defective part, must be returned
to an authorized service dealer within the warranty period.
The expense of delivering the product to the dealer for
warranty work and the expense of returning it back to the
owner after repair or replacement will be paid by the owner.
Homelite’s responsibility in respect to claims is limited to
making the required repairs or replacements and no claim
of breach of warranty shall be cause for cancellation or
rescission of the contract of sale of any HOMELITE brand
product. Proof of purchase will be required by the dealer
to substantiate any warranty claim. All warranty work must
be performed by a Homelite authorized service center.
This warranty is limited to ninety (90) days from the date of
original retail purchase for any HOMELITE brand product
that is used for rental or commercial purposes, or any other
income-producing purpose.
This warranty does not cover any HOMELITE brand product
that has been subject to misuse, neglect, negligence, or
accident, or that has been operated in any way contrary
to the operating instructions as specified in this operator’s
manual. This warranty does not apply to any damage to
the product that is the result of improper maintenance or
to any product that has been altered or modified. The
warranty does not extend to repairs made necessary
by normal wear or by the use of parts or accessories
which are either incompatible with the HOMELITE
brand product or adversely affect its operation,
performance, or durability. In addition, this warranty does
not cover:
A. Tune-ups – Spark Plugs, Carburetor, Carburetor
Adjustments, Ignition, Filters
B. Wear items – Bump Knobs, Outer Spools, Cutting Lines,
Inner Reels, Starter Pulleys, Starter Ropes, Drive Belts,
Tines, Felt Washers, Hitch Pins, Mulching Blades,
Blower Fans, Blower and Vacuum Tubes, Vacuum
Bags and Straps, Guide Bars, Saw Chains
Homelite reserves the right to change or improve the design
of any HOMELITE brand product without assuming any
obligation to modify any product previously manufactured.
ALL IMPLIED WARRANTIES ARE LIMITED IN DURATION
TO THE STATED WARRANTY PERIOD. ACCORDINGLY,
ANY SUCH IMPLIED WARRANTIES INCLUDING
MERCHANTABILITY, FITNESS FOR A PARTICULAR
PURPOSE, OR OTHERWISE, ARE DISCLAIMED IN
THEIR ENTIRETY AFTER THE EXPIRATION OF THE
APPROPRIATE TWO-YEAR OR NINETY-DAY WARRANTY
PERIOD. HOMELITE’S OBLIGATION UNDER THIS
WARRANTY IS STRICTLY AND EXCLUSIVELY LIMITED
TO THE REPAIR OR REPLACEMENT OF DEFECTIVE
PARTS AND HOMELITE DOES NOT ASSUME OR
AUTHORIZE ANYONE TO ASSUME FOR THEM ANY
OTHER OBLIGATION. SOME STATES DO NOT ALLOW
LIMITATIONS ON HOW LONG AN IMPLIED WARRANTY
LASTS, SO THE ABOVE LIMITATION MAY NOT APPLY
TO YOU. HOMELITE ASSUMES NO RESPONSIBILITY
FOR INCIDENTAL, CONSEQUENTIAL, OR OTHER
DAMAGES INCLUDING, BUT NOT LIMITED TO, EXPENSE
OF RETURNING THE PRODUCT TO AN AUTHORIZED
HOMELITE SERVICE CENTER AND EXPENSE OF
DELIVERING IT BACK TO THE OWNER, MECHANIC’S
TRAVEL TIME, TELEPHONE OR TELEGRAM CHARGES,
RENTAL OF A LIKE PRODUCT DURING THE TIME
WARRANTY SERVICE IS BEING PERFORMED, TRAVEL,
LOSS OR DAMAGE TO PERSONAL PROPERTY, LOSS
OF REVENUE, LOSS OF USE OF THE PRODUCT, LOSS
OF TIME, OR INCONVENIENCE. SOME STATES DO NOT
ALLOW THE EXCLUSION OR LIMITATION OF INCIDENTAL
OR CONSEQUENTIAL DAMAGES, SO THE ABOVE
LIMITATION OR EXCLUSION MAY NOT APPLY TO YOU.
This warranty gives you specific legal rights, and you may
also have other rights which vary from state to state.
This warranty applies to all HOMELITE brand products
manufactured by or for Homelite and sold in the United
States and Canada.
To locate your nearest Homelite authorized service
center, dial 1-800-242-4672 or log on to our website at
www.homelite.com.
Page 3 — Français
RÈGLES DE SÉCURITÉ GÉNÉRALES
AVERTISSEMENT :
LIRE ET VEILLER À BIEN COMPRENDRE TOUTES
LES INSTRUCTIONS. Le non respect des instructions
ci-dessous peut entraîner un choc électrique, un incendie
et / ou des blessures graves.
LIRE TOUTES LES INSTRUCTIONS
Pour travailler en toute sécurité, lire et veiller à bien
comprendre toutes les instructions avant d’utiliser ce
produit. Respecter toutes les instructions de sécurité.
Le non respect des instructions de sécurité ci-dessous
peut entraîner des blessures graves.
Ne pas laisser des enfants ou personnes n’ayant pas reçu
une formation adéquate utiliser cet outil.
Ne pas démarrer ou faire tourner le moteur dans un
espace confine, de bâtiment, à proximité des fenêtres
ouverts, autre ou des zones sans ventilation où des
vapeurs toxiques de monoxyde de carbone peuvent
s’accumuler. Le monoxyde de carbone, un gaz incolore,
inodore et extrêmement toxique peut causer une perte
de conscience et être mortel.
Déblayer la zone de travail avant chaque utilisation. La
débarrasser de tous les objets tels que cailloux, verre brisé,
clous, fils métalliques, cordes, etc. risquant d’être projetés
ou de se prendre dans la ligne de coupe ou la lame.
Toujours porter une protection oculaire avec écrans
latéraux certifiée conforme à la norme ANSI Z87.1 ainsi
qu’un protection auditive lors de l’utilisation de ce produit.
Si cette précaution n’est pas prise, des objets peuvent
être projetés dans les yeux et causer des lésions graves.
Porter des pantalons longs, manches longues, des
chaussures de travail et des gants épais. Ne pas porter
de vêtements amples, bijoux, shorts, sandales et ne pas
travailler pieds nus. Ne porter aucun bijou.
Le fait de porter des vêtements de protection lourds
peut augmenter la fatigue de l’utilisateur, ce qui pourrait
entraîner un coup de chaleur. Si le temps est chaud et
humide, effectuer les gros travaux le matin ou en fin
d’après-midi, alors qu’il fait plus frais.
Ne jamais utiliser cet outil en le tenant du côté gauche.
Attacher les cheveux longs pour les maintenir au-dessus
des épaules, afin qu’ils ne se prennent pas dans les
pièces en mouvement.
Garder les badauds, enfants et visiteurs à une distance de
15 m (50 pi). Recommander aux personnes présente de
porter une protection oculaire. Si quelqu’un s’approche
pendant l’utilisation de l’outil, arrêter le moteur et
l’accessoire de coupe. Le risque de blessure est accru
si on utilise un outil à lames. En effet, les personnes se
trouvant à proximité risquent d’être heurtés par une lame
en marche advenant qu’elle ricoche, ou à la suite de toute
autre réaction inattendue de la scie.
Ne pas utiliser cet outil en état de fatigue, si l’on est
souffrant ou contrarié ou sous l’influence de l’alcool, de
drogues ou de médicaments.
Ne pas travailler sous un éclairage insuffisant.
Se tenir bien campé et en équilibre. Ne pas travailler
hors de portée. Le travail hors de portée risque de faire
perdre l’équilibre ou de causer un contact avec les pièces
brûlantes.
Ne pas utiliser l’outil sur une échelle ou un support
instable. Une bonne tenue et un bon équilibre permettent
de mieux contrôler l’unité en cas de situation imprévue
Garder toutes les parties du corps à l’écart des pièces
en mouvement.
Pour éviter le contact avec les parties brûlantes, ne jamais
travailler avec le bas du moteur au-dessus du niveau de
la taille.
Ne pas toucher les alentours de l’échappement ou du
cylindre, qui deviennent brûlants pendant l’utilisation.
Contact avec les surfaces chaudes pourrait entraîner des
blessures graves.
Toujours arrêter le moteur et débrancher le fil de la bougie
avant d’effectuer tout entretien ou réglage, à l’exception
des réglages du carburateur.
Inspecter l’outil avant chaque utilisation pour s’assurer
qu’il n’y a pas de pièces desserrées, de fuites ce
carburant, etc. Remplacer les pièces endommagées
avant utilisation.
Ne jamais utiliser des lames, de dispositifs coudés, un
fil ou une corde avec ce accessoire taille-bordures. Ne
jamais utiliser des lames, un dispositif fouetteur, un fil ou
une corde sur une accessoire.
Lors d’une utilisation normale, l’accessoire de coupe ne
doit jamais tourner au ralenti. La rotation au ralenti est
toutefois permise lors du réglage du carburateur.
Il a été rapporté que, chez certaines personnes, les
vibrations produites par les outils à main motorisés peuvent
contribuer au développement d’une affection appelée
syndrome de Raynaud. Les symptômes peuvent inclure
des picotements, l’insensibilisation et le blanchissement
des doigts et sont habituellement provoqués par
l’exposition au froid. L’hérédité, l’exposition au froid et à
l’humidité, le régime alimentaire, la fumée et les habitudes
de travail sont tous des facteurs considérés comme
contribuant au développement de ces symptômes. Il
n’existe actuellement aucune preuve qu’un certain type
de vibration ou le degré d’exposition contribue réellement
au développement de cette affectation. Certaines
mesures, susceptibles de réduire les effets des vibrations,
peuvent être prises par l’opérateur :
a) Garder le corps au chaud par temps froid. Pendant
l’utilisation, porter des gants afin de tenir les mains et
les poignets au chaud. Il a été établi que le froid est
l’une des principales causes du symptôme de Raynaud.
Page 4 — Français
Inspecter l’outil avant chaque utilisation. Remplacer les
pièces endommagées. S’assurer que toutes les pièces
de boulonnerie sont en place et bien serrées. S’assurer
de l’absence de fuites de carburant.
Si la tête de coupe est fendue, brisée ou endommagée
de quelque façon que ce soit, la remplacer. S’assurer que
la tête de coupe est correctement installée et solidement
assujettie. S’il ne le sont pas, l’opérateur court des risques
de blessures graves.
S’assurer que tous les dispositifs de protection,
déflecteurs et poignées sont correctement installés et
solidement assujettis.
Ne jamais utiliser de lames ou de dispositifs à fléau, fil
et cordes. Utiliser exclusivement des lignes de coupe
recommandées ou équivalentes. Ne pas utiliser d’autres
accessoires de coupe. L’utilisation d’une tête de coupe
d’autre marque sur ce taille-bordures peut entraîner des
blessures graves.
Ne jamais utiliser l’outil si le déflecteur d’herbe n’est pas
en place et en bon état.
Tenir fermement les deux poignées pendant le travail.
Tenir la tête de coupe au-dessous du niveau de la taille.
Ne jamais tailler avec la tête de coupe à plus de 762 mm
(30 po) du sol.
Ce produit est conçu pour les personnes qui prévoient
l’utiliser de manière peu fréquente pour des applications
générales par exemple, tailler la végétation faible et dense
etc.; l’outil peut également convenir à d’autres utilisateurs
occasionnels. Elle n’est pas conçue pour un usage
prolongé. Les périodes d’utilisation prolongée peuvent
entraîner des problèmes circulatoires dans les mains
de l’opérateur, causés par les vibrations. Pour ce type
d’application, il peut être bon d’utiliser une scie équipée
d’un dispositif anti-vibrations.
Conserver ces instructions. Les consulter fréquemment et
les utiliser pour instruire les autres utilisateurs éventuels.
Si cet outil est prêté, il doit être accompagné de ces
instructions.
RÈGLES DE SÉCURITÉ PARTICULIÈRES
RÈGLES DE SÉCURITÉ GÉNÉRALES
b) Après chaque période d’utilisation, faire des exercices
pour accroître la circulation.
c) Faire des pauses fréquentes. Limiter la durée
d’exposition quotidienne.
d) Garder l’outil bien entretenu, toutes les pièces de
boulonnerie serrées et remplacer les pièces usées.
En cas d’apparition de l’un ou plusieurs des symptômes
décrits ci-dessus, cesser d’utiliser l’outil et consulter un
médecin.
Mélanger et conserver le carburant dans un bidon ou
jerrican approuvé pour l’essence.
Mélanger le carburant à l’extérieur, loin de toute flamme
ou source d’étincelles. Essuyer tout carburant répandu.
S’éloigner de 9 m (30 pi) du point d’approvisionnement
avant de lancer le moteur. Desserrer le bouchon du
réservoir de carburant lentement une fois que le moteur
est arrêté. Ne pas fumer pendant le ravitaillement en
carburant.
Arrêter le moteur et le laisser refroidir avant de faire le
plein ou de le remiser.
Laisser refroidir le moteur ; pour le transport dans un
véhicule, le réservoir doit être vidé dans un bidon ou
jerrycan approuvé pour l’essence et l’outil bien arrimé.
Porter un équipement de protection et respecter toutes
les instructions de sécurité. S’assurer que l’accessoire de
coupe s’immobilise lorsque le moteur tourne au ralenti.
Lorsque le moteur est arrêté, s’assurer que l’accessoire
de coupe est immobilisé avant de poser l’outil.
Il est recommandé d’apporter la équipement à un
centre de réparations qualifié pour la faire réparer pour
éviter que des réparations effectuées par une personne
inexpérimentée ou non qualifiée puissent endommager
la équipement, créer des conditions dangereuses, des
blessures à l’utilisateur et annuler la garantie.
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
-
1
-
2
-
3
-
4
-
5
-
6
-
7
-
8
-
9
-
10
-
11
-
12
-
13
-
14
-
15
-
16
-
17
-
18
-
19
-
20
-
21
-
22
-
23
-
24
-
25
-
26
-
27
-
28
-
29
-
30
-
31
-
32
-
33
-
34
-
35
-
36
-
37
-
38
-
39
-
40
-
41
-
42
-
43
-
44
Homelite UT33650 Manuel utilisateur
- Catégorie
- Coupe-herbe
- Taper
- Manuel utilisateur
dans d''autres langues
- English: Homelite UT33650 User manual
- español: Homelite UT33650 Manual de usuario
Documents connexes
-
Homelite ut33600, ut33650 Le manuel du propriétaire
-
-
Homelite ZR33600 Manuel utilisateur
-
-
-
-
-
-
-