Panasonic DMWMCTZ3E Le manuel du propriétaire

Operating Instructions

Bedienungsanleitung

Mode d’emploi

Instrucciones de funcionamiento

Istruzioni d’uso

Marine Case

Model No. DMW-MCTZ3

VQT1F26

Before use, please read these instructions completely.

Bitte lesen Sie diese Bedienungsanleitung vor der Inbetriebnahme des

Gerätes vollständig durch.

Lire intégralement ces instructions avant d’utiliser l’appareil.

Antes del uso, lea completamente estas instrucciones.

Leggere completamente queste istruzioni prima dell’uso.

E

VQT1F26.book 1 ページ２００７年２月６日　火曜日　午前１１時１８分

2

VQT1F26

Contents

Before Use . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3

Accessories . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5

Handling and Care . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6

Components. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8

What is the O-ring? . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9

Preparation -Setting the O-ring-. . . . . . . . . . . . . . . . . . . . . 10

Preparation -Checking the Case is Waterproof- . . . . . . . . 14

Preparation -Attaching the Digital Camera- . . . . . . . . . . . . 15

Taking Pictures . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18

Tips for Taking Pictures in the Water. . . . . . . . . . . . . . . . . 19

After Use . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20

Cleaning and Storing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21

Caution for Use . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21

Specifications. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23

Sales and Support Information

Customer Care Centre

• For customers within the UK:

08705 357357

• For customers within the Republic of

Ireland: 01 289 8333

• Visit our website for product information

• E-mail: customer[email protected]

Direct Sales at Panasonic UK

• Order accessory and consumable items

for your product with ease and

confidence by phoning our Customer

Care Centre Monday–Thursday

9.00 a.m.–5.30 p.m., Friday 9.30 a.m.–

5.30 p.m.

(Excluding public holidays)

• Or go on line through our Internet

Accessory ordering application at

www.panasonic.co.uk.

• Most major credit and debit cards

accepted.

• All enquiries transactions and distribution

facilities are provided directly by

Panasonic UK Ltd.

• It couldn’t be simpler!

• Also available through our Internet is

direct shopping for a wide range of

finished products, take a browse on our

website for further details.

Interested in purchasing an extended

guarantee?

Please call 0870 240 6284 or visit our

website www.panasonic.co.uk/guarantee

.

VQT1F26.book 2 ページ２００７年２月６日　火曜日　午前１１時１８分

3

VQT1F26

Before Use

≥ This Marine Case is designed for Panasonic Digital Camera.

You can enjoy taking pictures underwater at depths up to 40 m.

≥ In the case of water leakage due to insufficient care, Matsushita is in no way liable

for damage to any products (digital camera, batteries, card etc.) inside this Case,

photography costs or any other expenses.

≥ Matsushita also offers no compensation for accidents resulting in injury or damage

to property.

≥ Read the operating instructions for your digital camera.

≥ Before attaching the digital camera, submerge the case in water for about

3 minutes or more to check that there is no water leakage.

∫ About handling this Case

≥ Use under the following conditions.

• Water depth: Up to 40 m

• Ambient temperature: 0 °C

to

40 °C

≥ Do not use the Case in water over 40 °C. The heat may damage the Case or cause

water leakage.

≥ The Case is made of impact resistant polycarbonate however be careful when you

are using it. It can be easily scratched when taking pictures in rocky places etc. and

can be damaged by the impact if dropped etc. When travelling, pack the Case

carefully to prevent any direct impact if it is dropped etc. and do not leave the digital

camera in the Case. Only attach the digital camera to the case if you are

transporting it a short distance such as from the airport to the diving spot. (You

cannot reuse the material the Case was packed in at the time of purchase to

transport it.)

≥ When boarding a plane, the change in atmospheric pressure may cause the inside

of the Case to expand causing damage to the Case. Remove the O-ring before

boarding a plane.

≥ Do not leave the digital camera in the Case for a long period of time in a car, a

ship, exposed to direct sunlight etc. The Case is an airtight device so the

temperature inside the Case will become very high and the digital camera may

stop operating properly. Do not let the temperature inside the Case become

too high.

ENGLISH

VQT1F26.book 3 ページ２００７年２月６日　火曜日　午前１１時１８分

4

VQT1F26

Before Use (continued)

∫ Using the Case in high or low temperatures

≥ If you open or close the Case where it is humid or hot and then move to a place that

is cold or dive underwater, condensation may appear inside the Case, the glass

surface may become cloudy and the digital camera may be damaged.

≥ If you suddenly move the Case from a cold place or cold water to a warm place, the

glass surface may become cloudy. Wait until the Case becomes close to the air

temperature before taking pictures.

∫ About preparation

≥ Do not open or close the Case where it may be splashed by water or sand may

get in it. We recommend opening or closing the Case indoors.

≥ Replace the battery, card etc. and attach the digital camera indoors where there is

little moisture.

≥ If you must open or close the Case at the diving spot to replace the battery or

the card, be sure to follow the steps below.

• Select a place where the Case will not be splashed by water and sand will not get

in it.

• Blow off any drops of water in the gap between the rear case and the front case

and on the buckle. Thoroughly wipe off any remaining drops of water with a dry

cloth.

• Thoroughly wipe off any drops of water on your body or hair.

• Be particularly careful about any water coming from the sleeves of your thermal

suit.

• Do not touch the digital camera if your hands are wet from sea water. Wet a towel

with fresh water and place it in a polyester bag beforehand. Use this towel to wipe

off any drops of water or sand on your hands or body.

≥ This Case does not absorb shock. If you place a heavy object on the Case or cause

shock to it, the digital camera may be damaged. Be careful when you are using the

case.

VQT1F26.book 4 ページ２００７年２月６日　火曜日　午前１１時１８分

5

VQT1F26

Accessories

When you first open the package, check that the Case and all the

accessories are included and that there has been no damage to the

Case or any of the accessories during distribution or

transportation. If you find something unusual, consult your dealer

before using the Case.

Do not use any accessories except those specified below.

O-ring

VMG1798

Silica Gel (Desiccant)

(1 g /5 pieces)

VZG0371

Grease (for O-ring)

VZG0372

Hand Strap

VFC4190

Weights (2)

VMP8844

Weights attachment

screw

VHD1930

Diffuser

VYK2D90

≥ You can remove this diffuser when not using it.

Removing Attaching

Attach as shown in the diagram.

VQT1F26.book 5 ページ２００７年２月６日　火曜日　午前１１時１８分

6

VQT1F26

Handling and Care

≥ Do not place the Case where it may fall.

• If the Case falls on your head or foot, it will injure you and cause the Case to

malfunction.

≥ Never alter the Case.

• If water leaks into the digital camera because the Case was altered, the digital

camera may be damaged beyond repair.

• If you continue to use the digital camera after water has leaked into it, this may

cause a fire.

≥ Do not use the Case while scuba diving without proper training.

• You should only operate the Case while scuba diving if you have been properly

trained and certified for this sport.

≥ Never place the Case, grease, silica gel or O-ring within the reach of

infants.

• If any part of an infant’s body is caught in the Case, it may cause an injury.

• Infants may accidentally swallow the grease, silica gel or O-ring.

• Consult a doctor immediately if you think an infant may have swallowed the

grease, silica gel or O-ring.

≥ Do not hang the strap around your neck underwater.

• It may become wound around your neck causing suffocation or other serious

injuries.

≥ Thoroughly wash off any grease on your hands.

• Do not allow the grease on your hands to come into contact with your mouth or

eyes.

≥ If water leaks into the case, stop using it immediately.

• This may cause an electric shock, burning or a fire.

• Consult your dealer.

≥ If anything abnormal occurs while using the Case underwater, please

follow all necessary procedures and guidelines for decompressing

when you ascend.

• If you ascend too quickly, you may get caisson disease.

≥ If smoke or abnormal heat, smells or sounds come from the Case,

stop using it immediately.

• These may cause an electric shock, burning or fire.

• Remove the digital camera from the Case and then immediately remove the

battery from the digital camera.

• Consult your dealer.

≥ Be careful when opening the Case after water leakage.

• The leaked water may blow out or the rear case may flip.

VQT1F26.book 6 ページ２００７年２月６日　火曜日　午前１１時１８分

7

VQT1F26

≥ Do not leave the Case where the temperature is high.

• The temperature inside the Case becomes very high particularly when it is

exposed to direct sunlight on a beach, a ship etc. or when it is left in an airtight car

in the summer. The heat may damage the Case or its inner parts.

• If a digital camera is attached to the Case, it may also be damaged.

• If you use the attached digital camera when the temperature inside the Case is

very high, it may cause leakage, short-circuiting or insulation failure resulting in

fire or malfunction.

≥ Do not handle the digital camera or the battery with wet hands.

• This may cause an electric shock or malfunction.

∫ When taking pictures with the flash

≥ When taking pictures with the flash, the corners of the picture may be vignetted or

the picture may not be lit evenly.

≥ When taking pictures with the flash, the available flash range is less underwater

than on land.

VQT1F26.book 7 ページ２００７年２月６日　火曜日　午前１１時１８分

8

VQT1F26

Components

1. Zoom Lever

2. Strap Eyelet

(for attaching the supplied hand

strap and diffuser)

3. Shutter Button

4. Mode Dial

5. Front Case

6. Diffuser (supplied)

7. Front Glass

8. Camera ON/OFF Switch

9. 3/Exposure Compensation/

Auto Bracket/White Balance

Fine Adjustment/Backlight

Compensation In Simple

Mode Button

10. 1/Flash Setting Button

11. [MENU/SET] Button

12. [FUNC]/Delete button

13. 4/[REV] Button

14. [DISPLAY/LCD MODE] But-

ton

15. 2/Self-timer Button/AF Lock

16. Rear Case

17. Buckle

18. Lock Release Lever

12 3 4 5

6

8

9

10

11

12

17

18

13141516

7

VQT1F26.book 8 ページ２００７年２月６日　火曜日　午前１１時１８分

9

VQT1F26

What is the O-ring?

≥ The O-ring is a waterproofing packing used for underwater cameras, watches and

diving equipment.

≥ The O-ring keeps the Case waterproof by sealing the gap between the rear case

and the front case.

∫ How the O-ring keeps the Case waterproof

The gum comes into contact with the sides of the Case making the

Case waterproof and stopping water from entering from the gap.

When the O-ring is crushed by water pressure, the surface of

the O-ring expands and the Case is sealed more tightly.

The O-ring prevents water leakage by coming into uniform

contact with the sides of the Case. Therefore, good care of the

O-ring is very important. Incorrect care of the O-ring may

cause water leakage.

O-ring

Digital Camera

Front Case

Rear Case

O-ring

Water

pressure

VQT1F26.book 9 ページ２００７年２月６日　火曜日　午前１１時１８分

10

VQT1F26

Preparation -Setting the O-ring-

Be sure to set the O-ring before attaching a digital camera.

Thoroughly wash and dry your hands before handling the O-ring. Place

the O-ring where there is no sand or dust.

1

Loosen the O-ring with your fingers to remove it.

≥

Loosen part of the O-ring with the tips of two fingers and then lift the loosened

part. Be careful not to scratch the O-ring with your fingernails.

∫ Note

≥

Do not use a pointed object to remove the O-ring. This may scratch the O-ring.

O-ring

VQT1F26ENG-BODY.fm 10 ページ２００７年２月７日　水曜日　午後３時２分

11

VQT1F26

2

Check the O-ring.

≥ Check that there is no dirt, sand, hair, dust, salt crystals, lint or old grease on

the O-ring. If you find any of these, remove them with a soft, dry cloth.

≥ There may be dirt on the O-ring that you cannot see. Check if there is any dirt by

rubbing your finger over the O-ring.

≥ Be careful not to leave any fibers from the dry cloth on the O-ring when wiping it.

≥ Check that the O-ring is not ripped, twisted, squashed, frayed or scratched and

that there is no sand sticking to it. Replace the O-ring in these cases.

3

Inspect the O-ring groove.

≥ Grains of sand or hardened salt crystals may get into the O-ring groove.

Remove them carefully with an air spray or a cotton swab. If you use a cotton

swab, be careful not to leave any fibers from it in the O-ring groove.

3Dirt

3Sand

3

Hair

3Dust

3Salt crystals 3Lint

3Ripped

3Twisted

3Squashed 3Frayed

3Scratched 3Sand sticking

VQT1F26.book 11 ページ２００７年２月６日　火曜日　午前１１時１８分

12

VQT1F26

Preparation -Setting the O-ring- (continued)

4

Inspect the opposite side of the O-ring in the same way.

5

Apply the grease (supplied).

≥ Apply a rice-grain size of grease (supplied) evenly to the O-ring with the tip of

your finger.

≥ Dirt or dust will stick to the O-ring if you apply too much grease.

≥

Use only the specified grease. If you use other types of grease, the

surface of the O-ring may be damaged causing water leakage.

≥ Do not apply the grease with paper or a cloth. The fibers from the paper or cloth

may stick to the O-ring.

6

Fit the O-ring evenly into the O-ring groove.

Check the following:

≥ There is no dirt sticking to the O-ring.

≥ The O-ring has not come out.

≥ The O-ring is not twisted.

≥ The O-ring is not stretched too much.

CORRECT

INCORRECT

VQT1F26.book 12 ページ２００７年２月６日　火曜日　午前１１時１８分

13

VQT1F26

7

Inspect the O-ring one last time.

Check the following one more time:

≥ There is no dirt sticking to the O-ring.

≥ The O-ring has not come out.

≥ The O-ring is not twisted.

≥ There are no scratches or squashed parts on the O-ring.

Thoroughly wipe any grease off your hands with a dry cloth and then

wash your hands with water.

8

Close the buckle.

≥ Check that no foreign materials are sticking to the outer surface of the O-ring and

the buckle on the front case and then close the Case.

∫

Notes

≥ To keep the Case completely airtight, do not scratch the surface of the O-ring that

comes into contact with the sides of the Case.

≥ Never use an O-ring that has been scratched or damaged by dirt etc. This will cause

water leakage.

≥ Each time you use the Case, remove the O-ring and check that there is no dirt,

sand, hair or other foreign materials in the O-ring groove and then apply a thin coat

of grease (supplied). If you apply too much grease, dirt and the dust may stick to the

O-ring causing water leakage.

≥ Be sure to bring a spare O-ring in case the O-ring that you are using becomes

damaged or scratched.

1

2

VQT1F26.book 13 ページ２００７年２月６日　火曜日　午前１１時１８分

14

VQT1F26

Preparation -Checking the Case is Waterproof-

After setting the O-ring, check that no water leaks into the Case by

submerging it in a water tank, bath tub etc. for more than about

3 minutes before attaching a digital camera.

≥ Do not use the Case in water over 40 °C. The heat may damage the Case or cause

water leakage.

‘

Carry out the same test after attaching the digital camera to the Case. (P15)

∫

Notes

≥ If bubbles rise from the Case when it is submerged in water or there is water inside

the Case when you take it out the water, there is water leakage. In these cases,

consult your dealer.

≥ If water leaks into the Case while you are using it and the digital camera is

submerged in water, remove the battery immediately. Hydrogen gas can cause

burning or explosion if there is a fire nearby.

≥ If you dive quickly while holding the Case or throw the Case from a ship into the sea,

some water leakage may occur because of high pressure. This is not a malfunction

of the Case. Always dive slowly into the water.

≥ The Case is designed to be used at a depth of up to 40 m. If you dive deeper than

40 m, part of the Case may be damaged beyond repair.

≥ When closing the Case, be careful that no foreign materials get caught between the

O-ring and the O-ring groove. Even one strand of hair or one grain of sand can

cause water leakage.

VQT1F26.book 14 ページ２００７年２月６日　火曜日　午前１１時１８分

15

VQT1F26

Preparation -Attaching the Digital Camera-

Check that the ON/OFF Switch on the camera and the case is set to

[OFF].

≥ Remove the strap from the digital camera.

1

Push

2

up with your finger while sliding

1

to open the buckle.

2

Attach the digital camera to the Case.

≥ Be careful not to catch the shading ring 1.

3

Insert the silica gel (supplied).

≥ Always use new silica gel.

1

2

1

Silica gel

VQT1F26.book 15 ページ２００７年２月６日　火曜日　午前１１時１８分

16

VQT1F26

Preparation -Attaching the Digital Camera- (continued)

≥ When inserting the silica gel, bend it as shown in the illustration below

and then insert it as far as possible. If you close the Case with the silica

gel not fully inserted, the silica gel will get caught in the O-ring causing

water leakage.

≥ If the air temperature is high and the water temperature is low, condensation

may appear inside the Case. To prevent condensation, make sure that the silica

gel (supplied) does not come into contact with the digital camera lens. To

prevent the Case from becoming fogged up, insert the silica gel about 1 to

2 hours before using the Case.

4 Close the buckle.

‘

Check that the buckle is closed firmly.

Do not insert the strap etc. in the buckle.

5 After you have attached the digital camera, check one more time that

no water leaks into the Case. (P14)

1

2

VQT1F26.book 16 ページ２００７年２月６日　火曜日　午前１１時１８分

17

VQT1F26

∫ Notes

≥

Check one more time that the O-ring is fitted evenly into the O-ring groove.

≥ Avoid opening or closing the Case where there is a lot of sand or dust and in humid

or wet places.

≥

If there is a sudden change in temperature, condensation may appear inside the Case.

≥ If sunscreen or sun oil sticks to the Case, wash it off immediately with lukewarm

water to prevent reduced waterproofness or discolouration.

∫ Attaching the weights

About using the weights

Attach the weights to adjust to the preferred buoyancy when using the marine case.

Use them as necessary.

Refer to the following about buoyancy underwater.

1 If you use the digital camera and the marine case only:

They will float slowly in fresh water or seawater. (Plus buoyancy)

2 If you use the digital camera, the marine case and 1 weight:

They will float even more slowly in fresh water or seawater than

1.

(Plus buoyancy)

3 If you use the digital camera, the marine case and 2 weights:

They will sink slowly in fresh water or seawater. (Minus buoyancy)

How to attach the weights

If you use 1 weight, align the protruding part of

the weight with the tripod receptacle on the

marine case and then use the supplied screw

to attach it. If you use 2 weights, align the

projecting part of the second weight with the

indented part of the first weight so that the

weights do not overlap and then attach them

to the tripod receptacle.

∫ Note

≥

To prevent rusting, detach the weights after use, wipe off any salt and then store

them.

VQT1F26.book 17 ページ２００７年２月６日　火曜日　午前１１時１８分

18

VQT1F26

Taking Pictures

∫ Before taking pictures underwater

Check the following before diving.

≥

Is there sufficient remaining battery power?

≥ Is there sufficient memory in the card?

≥ Is the O-ring fitted evenly into the O-ring groove?

≥ Have you checked that no water leaks into the Case?

≥ Is the buckle closed firmly?

∫ Taking pictures

1 Turn the camera on.

2 Display the scene mode menu and then set [UNDERWATER].

≥

Read the operating instructions of the digital camera for details.

3 Aim the AF area on the LCD monitor at the subject you want to focus

on.

4 Press 2 ( ) to focus.

•Press 2 () again to cancel.

5 Press the shutter button fully to take the picture.

∫ Notes

≥

Before attaching the camera to the Case, we recommend setting the clock again.

(Read the operating instructions of the digital camera for details.)

≥ If there are any particles floating in front of the camera, it may focus on them instead

of the subject.

≥ If there are drops of water or dirt sticking to the front glass, you may not be able to

focus properly. Be sure to wipe the front glass before taking pictures.

ONOFF

1

2

ONOFF

Press 1 to release the lock

and then set to [ON].

Press 2 to lock.

VQT1F26.book 18 ページ２００７年２月６日　火曜日　午前１１時１８分

19

VQT1F26

Tips for Taking Pictures in the Water

When the image is too bluish in the water

1 Press 3 ( ) several times until [] appears.

2 Press 2 ()1 ()

to adjust the white balance.

3 Press [MENU/SET] to finish.

≥ You can also press the shutter button halfway to finish.

Select the best picture

Set the flash to [ ].

Using the auto bracket function (For models with an auto bracket function)

≥ Each time the shutter button is pressed, 3 pictures with different exposures are

automatically recorded. You can select the desired picture from the 3 pictures.

Use Burst mode

≥ When taking pictures of a fast-moving subject (a clownfish etc.), you can select

your favourite picture after taking the pictures using burst mode.

∫

Note

≥ For more information, read the operating instructions of the digital camera.

VQT1F26.book 19 ページ２００７年２月６日　火曜日　午前１１時１８分

20

VQT1F26

After Use

After finishing taking pictures, follow the steps below.

1

Submerge the Case in fresh water for about 30 minutes or more

without removing the digital camera to remove any salt crystals etc.

≥

Press all the operation buttons etc. on the Case to wash away any

seawater. If the salt crystals are not removed from the buttons etc., they

will harden and the buttons will become unoperable.

≥

Do not wash the Case with fast-running or pressurized water etc. as it may

cause water leakage.

2

Wipe the water with a dry cloth that has no salt crystals sticking to it

and then dry the Case completely.

≥ Do not dry the Case by exposing it to direct sunlight. This may

discolour

or

damage the Case or may hasten deterioration of the O-ring.

3

Open the rear case to remove the digital camera.

VQT1F26.book 20 ページ２００７年２月６日　火曜日　午前１１時１８分

La page charge ...

Panasonic DMWMCTZ3E Le manuel du propriétaire

Ce manuel convient également à

Panasonic DMWMCTZ3E Le manuel du propriétaire

dans d''autres langues

Documents connexes

Autres documents