Maytag MLG20PRCWW1 Guide d'installation

Marque: Maytag

Modèle: MLG20PRCWW1

Catégorie: Machines à laver

Taper: Guide d'installation

Ce manuel convient également à

I STALLATI

I CTI

COMMERCIAL STACKED WASHER/DRYER

GAS OR ELECTRIC

I CTI

LAVEUSE/SECHEUSE SUPERPOSEES

A USAGE COMMERCIAL

A GAZ OU ELECTRIGUE

TABLE OF CONTENTS

Page

Stacked Washer/Dryer Safety ................................................................ 2

Tools & Parts .............................................................................................. 5

Alternate Parts and Accessories ............................................................ 6

Dimensions/Clearances .......................................................................... 7

Stacked Washer/Gas Dryer Installation Requirements ................... 8

Stacked Washer/Electric Dryer

Installation Requirements ..................................................................... 10

Dryer Venting Requirements ............................................................... 12

Dryer Gas Supply Requirements ....................................................... 15

Installing Stacked Washer/Dryer ........................................................ 16

Washer Drain System ........................................................................... 19

Leveling ...................................................................................................... 20

Complete Installation .............................................................................. 21

Reversing Dryer Door Swing ................................................................ 22

Stacked Washer/Dryer Maintenance Instructions ........................... 24

If You Need Assistance .......................................................................... 25

Electronic Control Setup Instructions ............................................... 26

Warranty ................................................................................................... 32

TABLE DES MATII_RES

Page

Securite de la laveuse/secheuse superposees ............................... 33

Outils et pieces ...................................................................................... 36

Pieces supplGmentaires et accessoires ............................................ 37

Dimensions/Distances de degagement ........................................... 38

Exigences d'installation pour la laveuse/sGcheuse & gaz

superposees ............................................................................................. 39

Exigences d'installation pour la laveuse/sGcheuse 61ectriques

superposees .......................................................................................... 41

Exigences concernant 1'Gvacuation de la secheuse ...................... 43

Specifications de I'alimentation en gaz de la secheuse ............... 46

Installation de la laveuse/secheuse superposees ........................... 47

Systeme d'Gvacuation de la laveuse ................................................... 50

Nivellement ................................................................................................ 51

Achever I'installation ................................................................................ 52

Inversion du sens d'ouverture de la porte de la secheuse ............. 53

Instructions d'entretien de la laveuse/secheuse superposees ....55

Si vous avez besoin d'assistance ........................................................ 56

Instructions de reglage du tableau

de commande 61ectronique .................................................................. 57

Garanfie ................................................................................................... 64

W10434041 B www.maytagcom mercialla und ry.com

STACKED WASHER/DRYER SAFETY

Your safety and the safety of others are very important.

We have provided many important safety messages in this manual and on your appliance. Always read and obey all safety

messages.

This is the safety alert symbol.

This symbol alerts you to potential hazards that can kill or hurt you and others.

All safety messages will follow the safety alert symbol and either the word "DANGER" or "WARNING."

These words mean:

You can be killed or seriously injured if you don't immediately

follow instructions.

You can be killed or seriously injured if you don't follow

instructions.

All safety messages will tell you what the potential hazard is, tell you how to reduce the chance of injury, and tell you what can

happen if the instructions are not followed.

WARNING - of

=Clothes dryer installation must be performed by a qualified installer,

= install the clothes dryer according to the manufacturer's instructions and local codes.

- Do not install a clothes dryer with flexible plastic venting materials or flexible metal

(foil type) duct. if flexible metal duct is installed, it must be of a specific type identified

by the appliance manufacturer as suitable for use with clothes dryers. Flexible venting

materials are known to collapse, be easily crushed, and trap lint. These conditions will

obstruct clothes dryer airflow and increase the risk of fire.

- To reduce the risk of severe injury or death, follow all installation instructions,

=Save these instructions.

It is recommended that the owner post, in a prominent location, instructions for the customer's use in the event the customer

smells gas. This information should be obtained from your gas supplier.

m Post the following warning in a prominent location.

i FOR YOUR SAFETY

Do not store or use gasoline or other flammable vapors and liquids in the vicinity of this or any other appliance.

STACKED WASHER/DRYER SAFETY

WARNING: For your safety, the information in this manual must be followed to minimize I

the risk of fire or explosion, or to prevent property damage, personal injury, or death, j

- Do not store or use gasoline or other flammable vapors and liquids in the vicinity of this

or any other appliance.

- WHAT TO DO iF YOU SMELL GAS:

= Do not try to light any appliance.

• Do not touch any electrical switch; do not use any phone in your building.

• Clear the room, building, or area of all occupants.

o Immediately call your gas supplier from a neighbor's phone. Follow the gas supplier's

instructions.

• if you cannot reach your gas supplier, call the fire department.

- Installation and service must be performed by a qualified installer, service agency, or

the gas supplier.

WARNING: Gas leaks cannot always be detected by smell.

Gas suppliers recommend that you use a gas detector approved by UL or CSA.

For more information, contact your gas supplier.

If a gas leak is detected, follow the "What to do if you smell gas" instructions.

iMPORTANT: The gas installation must conform with local codes, or in the absence of local codes, with the Canadian Natural Gas

and Propane Installation Code, CSA B149.1.

The dryer must be electrically grounded in accordance with local codes, or inthe absence of local codes, with the Canadian

Electrical Code, CSA C22.1.

STACKED WASHER/DRYER SAFETY

iMPORTANT SAFETY iNSTRUCTiONS

WARNING: To reduce the risk of fire, electric shock, or injury to persons when using the washer/dryer, follow basic

precautions, including the following:

[] Read all instructions before using the washer/dryer.

[] Do not place items exposed to cooking oils in your dryer.

items contaminated with cooking oils may contribute to a

chemical reaction that could cause a load to catch fire.

[] Do not wash or dry articles that have been previously

cleaned in, washed in, soaked in, or spotted with gasoline,

dry-cleaning solvents, other flammable, or explosive

substances as they give off vapors that could ignite or

explode.

[] Do not add gasoline, dry=cleaning solvents, or other

flammable, or explosive substances to the wash water.

These substances give off vapors that could ignite or

explode.

[] Do not allow children to play on or in the washer/dryer.

Close supervision of children is necessary when the

washer/dryer is used near children.

[] Before the washer/dryer is removed from service or

discarded, remove the doors to the washer/dryer

compartments.

[] Do not reach into the washer/dryer if the tub, agitator or

drum is moving.

[] Do not install or store the washer/dryer where it will be

exposed to the weather.

[] Do not tamper with controls.

[] Clean dryer lint screen before or after each load.

[] Under certain conditions, hydrogen gas may be produced

in a hot water system that has not been used for 2 weeks

or more. HYDROGEN GAS iS EXPLOSIVE. if the hot water

system has not been used for such a period, before using

the washing machine, turn on all hot water faucets and let

the water flow from each for several minutes. This will

release any accumulated hydrogen gas. As the gas is

flammable, do not smoke or use an open flame during

this time.

[] Do not repair or replace any part of the washer/dryer or

attempt any servicing unless specifically recommended in

this Use and Care Guide or in published user=repair

instructions that you understand and have the skills to

carry out.

[] Do not use fabric softeners or products to eliminate static

unless recommended by the manufacturer of the fabric

softener or product.

[] Do not use heat to dry articles containing foam rubber or

similarly textured rubber-like materials.

[] Keep area around the exhaust opening and adjacent

surrounding areas free from the accumulation of lint, dust,

and dirt.

[] The interior of the machine and dryer exhaust vent should

be cleaned periodically by qualified service personnel

[] See "Electrical Requirements" section of the Installation

Instructions booklet for grounding instructions.

SAVE THESE iNSTRUCTiONS

Tools Needed:

8" (203 ram)

or I0" (254 ram)

Pipe Wrench

Torx _ T-20 Security

Screwdriver or Bit

Level

TOOLS & PARTS

8" (203 mm) or 10" (254 ram)

Adj ustable Wrench

That Opens to 1" (25 ram)

1" (25 ram) Hex-Head

Socket Wrench

Utility Knife

Flat-Blade Screwdriver

5/16" Socket Wrench

1/4" (6 ram) Nut Driver

Phillips Screwdriver

Pliers

(that open to 19/10"[39 mini)

Locking Pliers

Caulk Gun and Caulk Vent Clamps Pipe-Joint Compound

(for installing new exhaust vent) Suitable for Gas Type

27" (686 ram) Wood Block

Flashlight (optional)

112" (13 ram) and 9/16"

(14 ram) Open-End Wrenches

Ruler or Measuring Tape

Parts Supplied:

Water Inlet Hoses (2)

Beaded Tie Strap

Inlet Hose Washers (4)

Drain Hose/Clamp

U-Shaped Hose Form Transit Bolt Hole Plug (4)

t-_:' TORX is a registered trademark of Saturn Fasteners, Inc. 5

ALTERNATE PARTS AND ACCESSORIES

Alternate Parts

Your installation may require additional parts. If you are interested

in purchasing one of the items listed here, call the toIFfree number

in the "If You Need Assistance" section.

If You Have You Will Need to Buy

Overhead sewer Standard 20 gal. (76 L) 39"

(990 mm) tall drain tub or utility sink,

sump pump and connectors (available

from local plumbing suppliers)

1" (25 mm) standpipe 2" (51 mm) diameter to 1" (25 mm)

diameter Standpipe Adapter

Part Number 3363920

Connector Kit Part Number 285835

Drain hose too short Extension Drain Hose Part

Number 285863

Connector Kit Part Number 285835

Lint clogged drain Drain Protector Part Number 367031

Connector Kit Part Number 285835

Floor drain system Siphon break, Part Number 285834

Connector Kit (x2) Part Number

285835

Extension Drain Hose Part

Number 285863

Water faucets

beyond reach

of fill hoses

2 longer water fill hoses:

6 ft. (1.8 m) 90 ° bend hose

Part Number 76314

10 ft. (3.0 m) Part Number 350008

Accessories

Enhance your washer/dryer with these premium accessories.

For more high-quality items or to order,

call 1-800-807-6777 or visit us at

www.whirlpoolparts.ca.

Part Number Accessory

8212526 Washer drip tray, fits under all

31682 AIFpurpose appliance cleaner

1903WH Laundry supply storage cart

279818 3-way dryer venting kit

285834 Siphon break kit

DiM ENS iONS/CLEARANCES

Dimensions

Front View Side View Back View

74"

(188(ram)

_ 27" _

(686 ram)

5J "

(1295 ram)

74"

1880 ram)

i_,, 291/2" _ _,,

(25 ram) (751 ram) (25 ram)

27 _l

_ 61/2''

(165 ram)

1ii

(25 mm)

661/4 ''

(1683 ram)

61/. ''

{159 ram)

41/8'' 69"

(105 ram) (1753 ram)

36"

(914 mm)

Clearances

Side Clearances

Back/Top Clearances

O" _ '._ O"

(O ram) (O ram)

j__ j_

,.,,i-..--O" 4 "-'''i_

(Omm) ('102mm)

STACKED WASHER/GAS DRYER iNSTALLATiON

REQUIREMENTS

Stacked Washer/Gas Dryer Location

Explosion Hazard

Keep flammable materials and vapors, such as

gasoline, away from dryer.

Do not install in a garage.

Failure to do so can result in death, explosion, or fire.

Selecting the proper location for your washer/dryer improves

performance and minimizes noise and possible washer "walk"

Your washer/dryer can be installed in a basement, laundry room, or

recessed area. See "Drain System:'

Companion appliance location requirements should also be

considered.

IMPORTANT: Do not install or store the washer/dryer where it will

be exposed to the weather. Do not store or operate the washer/

dryer in temperatures at or below 32°F (0°C). Some water can

remain in the washer and can cause damage in low temperatures.

Proper installation is your responsibility.

You will need:

m A water heater set to deliver 120°F (49°C) water to the washer.

m Hot and cold water faucets located within 4 ft. (1.2 m) of the

hot and cold water fill valves, and water pressure of 20-100

psi (137.9-689.6 kPa).

m A level floor with a maximum slope of 1" (25 mm) under

entire washer/dryer. Installing the washer/dryer on soft floor

surfaces, such as carpets or surfaces with foam backing, is not

recommended.

A sturdy and solid floor to support the washer/dryer with

a total weight (water and load) of 450 Ibs (204 kg).

m A floor drain under the bulkhead. Prefabricated bulkheads with

electrical outlets, water inlet lines, and drain facilities should be

used only where local codes permit.

Stacked washer/gas dryer installation clearances

m The location must be large enough to allow the washer

and dryer doors to be fully opened.

m Additional spacing should be considered for ease of installation

and servicing. The doors open more than 180 °. The washer

door is not reversible.

m Additional clearances might be required for wall, door, and floor

moldings.

m Additional spacing of 1" (25 mm) on all sides of the washer/

dryer is recommended to reduce noise transfer.

m Companion appliance spacing should also be considered.

When installing a gas dryer:

IMPORTANT: Observe all governing codes and ordinances.

m Check code requirements: Some codes limit or do not

permit installation of clothes dryers in garages, closets,

or sleeping quarters. Contact your local building inspector.

m Make sure that lower edges of the cabinet, plus the back and

bottom sides of the washer, are free of obstructions to permit

adequate clearance of air openings for combustion air. See

"Recessed Area Installation Instructions" below for minimum

spacing requirements.

Recessed Area Installation Instructions

This washer/dryer may be installed in a recessed area. For

recessed area installations, minimum clearances can be found

on the warning label on the rear of the dryer or in "Dimensions/

Clearances_'

The installation spacing is in inches and is the minimum allowable.

Additional spacing should be considered for ease of installation,

servicing, and compliance with local codes and ordinances.

The dryer must be exhausted outdoors.

iii

STACKED WASHER/GAS DRYER iNSTALLATiON

REQUIREMENTS

Stacked Washer/Gas Dryer Electrical Requirements Stacked Washer/Gas Dryer Gas Supply

IM PORTANT: The washer/dryer must be electrically grounded

in accordance with local codes and ordinances or, in the

absence of local codes, with the Canadian Electrical Code, CSA

C22.1. If codes permit and a separate ground wire is used, it is

recommended that a qualified electrical installer determine that the

ground path is adequate.

A copy of the above code standards can be obtained from:

CSA International

8501 East Pleasant Valley Road

Cleveland, Ohio 44131-5575

lu Do not ground to a gas pipe.

lu Do not have a fuse in the neutral or ground circuit.

In A 120 volt, 60 Hz, AC only, 15- or 20-amp, fused electrical

circuit is required. A time-delay fuse or circuit breaker is also

recommended. It is recommended that a separate circuit

serving only this washer/dryer be provided.

In If codes permit and a separate ground wire is used, it is

recommended that a qualified electrician determine that the

ground path is adequate.

In Check with a qualified electrician if you are not sure the

washer/dryer is properly grounded.

Explosion Hazard

Use a new CSA International approved gas supply line.

Install a shut=off valve.

Securely tighten all gas connections.

If connected to LP, have a qualified person make sure

gas pressure does not exceed 13" (330 ram) water

column.

Examples of a qualified person include:

licensed heating personnel,

authorized gas company personnel, and

authorized service personnel.

Failure to do so can result in death, explosion, or fire.

Stacked Washer/Gas Dryer Grounding

GROUNDING INSTRUCTIONS

For a permanently connected washer/dryer:

This appliance must be connected to a grounded metal,

permanent wiring system, or an equipment grounding

conductor must be run with the circuit conductors and

connected to the equipment=grounding terminal or lead

on the appliance.

WARNING" Improper connection of the equipment-

grounding conductor can result in a risk of electric shock.

Check with a qualified electrician or service representative

or personnel if you are in doubt as to whether the appliance

is properly grounded.

SAVE THESE INSTRUCTIONS

I MPORTANT: Observe all governing codes and ordinances.

This installation must conform with all local codes and ordinances.

In the absence of local codes, installation must conform with CAN/

CSA B149.

A copy of the above code standards can be obtained from:

CSA International

8501 East Pleasant Valley Road

Cleveland, Ohio 44131-5575

The design of this washer/dryer has been certified by CSA

International for use at altitudes up to 10,000 feet (3048 m) above

sea level at the B.T.U. rating indicated on the model/serial plate.

Burner input adjustments are not required when the washer/dryer

is operated up to this elevation.

When installed above 10,000 feet (3048 m), a four percent (40/0)

reduction of the burner B.T.U. rating shown on the model/serial

plate is required for each 1,000 foot (305 m) increase in elevation.

For assistance when converting to other gas types and/or installing

above 10,000 feet (3048 m) elevation, contact your local service

company.

STACKED WASHER/ELECTRIC DRYER iNSTALLATiON

REQUIREMENTS

Stacked Washer/Electric Dryer Location

Explosion Hazard

Keep flammable materials and vapors, such as

gasoline, away from dryer.

Do not instafl in a garage.

Failure to do so can result in death, explosion, or fire.

Selecting the proper location for your washer/dryer improves

performance and minimizes noise and possible washer "walk/'

Your washer/dryer can be installed in a basement, laundry room, or

recessed area. See "Drain System/'

Companion appliance location requirements should also be

considered.

IM PORTANT: Do not install or store the washer/dryer where it will

be exposed to the weather. Do not store or operate the washer/dryer

in temperatures at or below 32°F (0°C). Some water can remain

in the washer and can cause damage in low temperatures. Proper

installation is your responsibility.

You will need:

m A water heater set to deliver 120°F (49°0) water to the washer.

m Hot and cold water faucets located within 4 ft. (1.2 m) of the

hot and cold water fill valves, and water pressure of 20-100 psi

(137.9-689.6 kPa).

m A level floor with a maximum slope of 1" (25 mm) under

entire washer/dryer. Installing the washer/dryer on soft floor

surfaces, such as carpets or surfaces with foam backing, is not

recommended.

m A sturdy and solid floor to support the washer/dryer with a total

weight (water and load) of 450 Ibs (204 kg).

m A floor drain under the bulkhead. Prefabricated bulkheads with

electrical outlets, water inlet lines, and drain facilities should be

used only where local codes permit.

Stacked washer/electric dryer installation clearances

m The location must be large enough to allow the washer and

dryer doors to be fully opened.

In Additional spacing should be considered for ease of installation

and servicing. The doors open more than 180 °. The washer

door is not reversible.

In Additional clearances might be required for wall, door, and floor

moldings.

In Additional spacing of 1" (25 mm) on all sides of the washer/

dryer is recommended to reduce noise transfer.

m Companion appliance spacing should also be considered.

Recessed Area Installation Instructions

This washer/dryer may be installed in a recessed area. For

recessed area installations, minimum clearances can be found on

the warning label on the rear of the dryer.

The installation spacing is in inches and is the minimum allowable.

Additional spacing should be considered for ease of installation,

servicing, and compliance with local codes and ordinances.

The dryer must be exhausted outdoors.

STACKED WASHER/ELECTRIC DRYER iNSTALLATiON

REQUIREMENTS

Stacked Washer/Electric Dryer Electrical

Requirements

Washer Electrical Requirements

Do not have a fuse in the neutral or ground circuit.

m If codes permit and a separate ground wire is used, it is

recommended that a qualified electrician determine that

the ground path is adequate.

m Check with a qualified electrician if you are not sure the washer

is properly grounded.

Stacked Washer/Electric Dryer Grounding

GROUNDING iNSTRUCTiONS

For a permanently connected washer/dryer:

This appliance must be connected to a grounded metal,

permanent wiring system, or an equipment grounding

conductor must be run with the circuit conductors and

connected to the equipment-grounding terminal or lead

on the appliance.

WARNING: Improper connection of the equipment-

grounding conductor can result in a risk of electric shock.

Check with a qualified electrician or service representative

or personnel if you are in doubt as to whether the appliance

is properly grounded.

SAVE THESE iNSTRUCTiONS

Dryer Electrical Requirements

It isyour responsibility:

m To contact a qualified electrical installer.

m To be sure that the electrical connection is adequate and in

conformance with the Canadian Electrical Code.

The Canadian Electrical Code requires a 4-wire power supply

connection.

m To supply the required 4 wire, single phase, 240 volt, 60 Hz.,

AC only electrical supply (or 4 wire, 120/208 volt electrical

supply, if specified on the serial/rating plate) on a separate

40-amp circuit, fused on both sides of the line. A time delay

fuse or circuit breaker is recommended. Connect to an

individual branch circuit. Do not have a fuse in the neutral

or grounding circuit.

m Do not use an extension cord.

m If codes permit and a separate ground wire is used, it is

recommended that a qualified electrician determine that the

ground path is adequate.

Electrical Connection

This dryer is supplied/fitted with an electrical

supply cord and plug. It should be connected

to a 4-wire electrical supply receptacle of

NEMA Type 14-50P, at the voltage shown

on the rating plate. The dryer must be

positioned so that the plug is clearly visible and

accessible. This plug also provides the function

of an emergency stop control for the user. If the

fitted plug is not used, the electrical connection

4-Wire Receptacle

(14-50P)

must be carried out by a competent electrician in accordance with

local or national codes.

If the supply cord is damaged, it must be replaced with a specially

terminated cord by an authorized service agent or a similarly

competent person in order to avoid a hazard.

DRYER VENTING REQUIREMENTS

Fire Hazard

Use a heavy metal vent.

Do not use a plastic vent.

Do not use a metal foil vent,

Failure to follow these instructions can result in death

or fire.

WARN ING: To reduce the risk of fire, this dryer MUST BE

EXHAUSTED OUTDOORS.

IMPORTANT: Observe all governing codes and ordinances.

Dryer exhaust must not be connected into any gas vent, chimney,

wall, ceiling, attic, crawlspace, or a concealed space of a building.

Only rigid or flexible metal vent shall be used for exhausting.

4" (102 ram) heavy, metal exhaust vent

[] Only a 4" (102 mm) heavy, metal exhaust vent and clamps may

be used.

[] Do not use plastic or metal foil vent.

Rigid metal vent:

[] Recommended for best drying performance and to avoid

crushing and kinking.

Flexible metal vent: (Acceptable only if accessible to

clean)

[] Must be fully extended and supported in final dryer location.

[] Remove excess to avoid sagging and kinking that may result in

reduced airflow and poor performance.

[] Do not install in enclosed walls, ceilings, or floors.

[] The total length should not exceed 73/4ft. (2.4 m).

NOTE: If using an existing vent system, clean lint from entire length

of the system and make sure exhaust hood is not plugged with

lint. Replace plastic or metal foil vents with rigid metal or flexible

metal vents. Review "Vent System Chart" and if necessary, modify

existing vent system to achieve best drying performance.

Elbows:

[] 45 ° elbows provide better airflow than 90 ° elbows.

Clamps:

[] Use clamps to seal all joints.

[] Exhaust vent must not be connected or secured with screws

or other fastening devices that extend into interior of duct and

catch lint. Do not use duct tape.

Improper venting can cause moisture and lint to collect

indoors, which may result in:

[] Moisture damage to woodwork, furniture, paint, wallpaper,

carpets, etc.

[] Housecleaning problems and health problems.

DRYER VENTING REQUIREMENTS

Vent Hoods

4" (102 mm) Diameter Exhaust Hoods

Box Hood Louvered Hood Angled Hood

Exhaust hood must be at least 12" (305 mm) from the ground or

any object that may be in the path of the exhaust (such as flowers,

rocks, bushes, or snow).

Vent System Length

Maximum Vent Length/Vent Connection

Maximum length of vent system depends upon the type of vent

used, number of elbows, and type of exhaust hood.

3. Tighten hose clamp with Phillips screwdriver.

Vent System Chart (Rigid Metal Vent)

No. of Box and Angled

90° Turns Louvered Hood Hood

135 ft. (41.2 m)

125 ft. (38.1 m)

115 ft. (35.1 m)

106 ft. (32.3 m)

98 ft. (29.9 m)

129 ft. (39.3 m)

119 ft. (36.3 m)

109 ft. (33.2 m)

100 ft. (30.5 m)

92 ft. (28.0 m)

For vent systems not covered by the vent specification chart, see

your parts distributor.

Provision must be made for enough air for combustion and

ventilation. (Check governing codes and ordinances.) See

"Recessed Area Installation Instructions" in the "Stacked Washer/

Gas Dryer Location" and "Stacked Washer/Electric Dryer

Location" sections.

A 4" (102 mm) outlet hood is preferred. However, a 21/2'' (64 mm)

outlet exhaust hood may be used. A 21/2'' (64 mm) outlet creates

greater back pressure than other hood types. For permanent

installation, a stationary vent system is required.

Connect Vent

1. If connecting to existing vent, make sure the vent is clean.

2. Using a 4" (102 ram) clamp, connect vent to exhaust outlet in

dryer.

jyvoo,oo,,o,

4. Make sure the vent is secured to exhaust hood with a 4"

(102 ram) clamp.

5. Move dryer into final position. Do not crush or kink vent. Make

sure dryer is level.

NOTE: Do not remove vent collar.

DRYER VENTING REQUIREMENTS

If an Exhaust Hood Cannot be Used

The outside end of main vent should have a sweep elbow directed

downward.

*M,n,mumclearanceabove_--

a_c_mulation of snow ice ory

debris such as leaves

If main vent travels vertically through the roof, rather than through

wall, install a 180 ° sweep elbow on end of vent at least 2 fl.

(610 mm) above surface of roof.

The opening in wall or roof shall have a diameter 1/2" (13 mm)

larger than vent diameter. Vent should be centered in opening.

Do not install screening over end of vent for best performance.

Multiple Dryer Venting

A main vent can be used for venting a group of dryers. The

main vent should be sized to remove 200 CFM of air per dryer.

Large-capacity lint screens of proper design may be used in main

vent if checked and cleaned frequently. The room where the dryers

are located should have make-up air equal to or greater than CFM

of all the dryers in the room.

Back-draft Damper Kit, Part No. 339191 O, is available from your

distributor and should be installed in the vent of each dryer to

keep exhausted air from returning into dryers and to keep exhaust

in balance within main vent. Unobstructed return air openings are

required.

Each vent should enter the main vent at an angle pointing in

the direction of the airflow. Vents entering from the opposite side

should be staggered to reduce the exhausted air from interfering

with the other vents.

The maximum angle of each vent entering the main vent should be

no more than 30 °,

DRYER GAS SUPPLY REQUIREMENTS

Type of Gas

This dryer is equipped for use with natural gas. It is design-certified

by CSA International for LP (propane and butane) gases with

appropriate conversion. No attempt shall be made to convert dryer

from gas specified on serial/rating plate for use with a different gas

without consulting the serving gas supplier. Conversion must be

done by a qualified service technician.

Gas conversion kit part numbers are listed on gas valve burner

base.

Gas Supply Line

Recommended Method

Provide a gas supply line of 1/2" (1 3 mm) rigid (IPS) pipe to dryer

location. Pipe joint compounds that resist action of LP gas must be

used. Do not use TEFLON Rttape. With LP gas, piping or tubing

size can be 1/2" (1 3 mm) minimum. Usually, LP gas suppliers

determine size and materials used in the system.

Flexible Metal Appliance Connector

It is recommended that a new flexible stainless steel gas line,

design-certified by CSA International, be used for connecting the

dryer to the gas supply line. (The gas pipe which extends through

the lower rear of the dryer is provided with 3/8" (10 mm) male pipe

thread.)

Gas Supply Pressure Testing

A 1/8" (3 mm) NPT minimum plugged tapping, accessible for

gauge testing, must be installed immediately downstream of the

installed shut-off valve to the dryer (as shown above). The dryer

must be disconnected from the gas supply piping system during

any pressure testing of the system at test pressures in excess of

1/2" psig (352 kg/m2).

AIternate Method

The gas supply may also be connected using 3/8" (10 mm)

approved copper or aluminum tubing. If the total length of the

supply line is more than 20 ft. (6.1 m), larger tubing will be

required.

If using natural gas, do not use copper tubing. Pipe joint

compounds that resist action of type of gas supplied must

be used.

Shut-off valve required

The supply line must be equipped with an individual manual

shut-off valve installed within 6 ft. (1.8 m) of dryer in accordance

with the B149 installation codes CAN/CGA B149.1 and CAN/

CGA B149.2. This valve should be located in same room as dryer.

It should be in a location that allows ease of opening and closing.

Do not block access to shut-off valve.

NOTE: Do not kink or damage the flexible stainless steel gas line

when moving the door.

Rigid Pipe Connection

The rigid pipe connection requires a combination of pipe fittings to

obtain an in-line connection to dryer.

t-_TEFLON isa registeredtrademarkof E.I.DuPont DeNemoursandCompany.

iNSTALLiNG STACKED WASHER/DRYER

Remove Transport System

NOTE: Slide washer/dryer onto cardboard or hardboard before

moving to avoid damaging floor covering.

Excessive Weight Hazard

Use two or more people to move and install washer/dryer,

Failure to do so can result in back or other injury.

IM PORTANT: Position the washer/dryer so that the rear of the

washer is within approximately 3 ft. (900 mm) of its final location.

There are 4 shipping bolts in the rear panel of the washer that

support the suspension system during transportation. These bolts

also retain the power cord inside the washer until the bolts are

removed.

1. Keep the washer/dryer in the upright position while removing

the shipping bolts.

2. Using a 1/2" (13 mm) wrench, loosen each of the bolts.

4. Close the bolt holes with the 4 transport bolt hole plugs.

IMPORTANT: If the washer/dryer is to be transported, call your

product distributor or installer. To avoid suspension and structural

damage, your washer/dryer must be properly set up for relocation

by a trained professional.

3. Once the bolt is loose, move it to the center of the hole

and completely pull out the bolt, including the plastic spacer

covering the bolt. Once all 4 bolts are removed, discard the

bolts and spacers.

iNSTALLiNG STACKED WASHER/DRYER

Connect Inlet Hoses

Insert new hose washers (supplied) into each end of the inlet

hoses. Firmly seat the washers in the couplings.

Washer Coupming

Connect Inlet Hoses to Water Faucets

Make sure the washer drum is empty.

1. Attach a hose to the hot water faucet. Screw on coupling

by hand until it is seated on the washer.

Connect Inlet Hoses to Washer

1. Attach the cold water hose to the washer's cold water inlet

valve. Screw on coupling by hand until it is seated on the

washer.

2. Attach the hot water hose to the washer's hot water inlet valve,

Screw on coupling by hand until it is seated on the washer,

2. Attach a hose to the cold water faucet. Screw on coupling

by hand until it is seated on the washer.

3. Using pliers, tighten the couplings with an additional two-thirds

turn.

3. Using pliers, tighten the couplings with an additional

two-thirds turn.

NOTE: Do not overtighten or use tape or sealants on the valve.

Damage to the valves can result,

Clear Water Lines

m Run water through both faucets and inlet hoses, into a laundry

tub, drainpipe, or bucket, to get rid of particles

in the water lines that might clog the inlet valve screens.

m Check the temperature of the water to make sure that the hot

water hose is connected to the hot water faucet and that the

cold water hose is connected to the cold water faucet.

NOTE: Do not overfighten. Damage to the valve can result,

4. Turn on the water faucets completely and check for leaks,

NOTE: Replace inlet hoses after 5 years of use to reduce the

risk of hose failure. Record hose installation or replacement

dates on the hoses for future reference.

Periodically inspect and replace hoses if bulges, kinks, cuts,

wear, or leaks are found.

iNSTALLiNG STACKED WASHER/DRYER

Route Drain Hose

Proper routing of the drain hose avoids damage to your floor due to 3. Once the drain hose is in place, release the pliers.

water leakage. Read and follow these instructions.

Remove drain hose from the washer drum

1. Using locking pliers, squeeze hose clamp tabs together and

insert over the end of the drain hose.

4. The washer drain system can be installed using a floor drain,

wall standpipe, floor standpipe, or laundry tub.

2. Slide the drain hose onto the washer connection.

Laundry tub drain or standpipe drain

Connect the drain hose form to the corrugated drain hose.

Snap either end of the drain hose form to the drain

hose at the point where the corrugation begins.

Bend drain hose over drain hose form and snap

into place.

NOTE: Hose must not extend more than 1"

(25 mm) past the end of the U bend.

To keep drain water from going back into the washer:

Do not straighten the drain hose, do not force excess drain

hose into standpipe. Hose should be secure, but loose enough

to provide a gap for air.

m Do not lay excess hose on the bottom of the laundry tub.

Floor drain

You may need additional parts. See "Alternate Parts_'

Secure Drain Hose

1. Drape the power cord over the washer top.

2. Move the washer to its final location.

3. Place the drain hose in the "_

laundry tub or standpipe as

shown.

4. Secure the drain hose using ---

41/2""

the supplied beaded tie strap. (114 ram)

5. If the washer faucets and the drain

standpipe are recessed, put the

hooked end of the drain hose in

the standpipe as shown.

NOTES:

m Do not force excess drain hose

back into the rear of the washer.

m To avoid siphoning, do not seal

the drain hose into the standpipe.

WASHER DRAIN SYSTEM

The washer can be installed using the standpipe drain system

(floor or wall), the laundry tub drain system, or the floor drain

system.

Standpipe drain system - wall or floor

The standpipe drain requires a minimum diameter standpipe of 2"

(50 ram). The minimum carry-away capacity can be no less than

10 gal. (38 L) per minute.

Wall

Laundry tub drain system

The laundry tub needs a minimum 20 gal. (76 L) capacity. The top

of the laundry tub must be at least 30" (762 mm) above the floor.

30"

(762 ram)

The top of the standpipe must be at least 30" (762 mm) high and

no higher than 96" (2.4 m) from the bottom of the washer.

Floor

30" rain.

Floor drain system

The floor drain system requires a siphon break that may be

purchased separately.

The siphon break (Part Number 285834) must be a minimum of

28" (710 mm) from the bottom of the washer. Additional hoses

might be needed.

Syphon-

break _

28"

LEVELING

Leveling Stacked Washer/Dryer

Leveling your washer/dryer properly reduces excess noise and

vibration.

Excessive Weight Hazard

Use two or more people to move and install washer/dryer.

Failure to do so can result in back or other injury.

1. Remove cardboard from beneath washer/dryer. Place a level on

top edges of washer/dryer, checking each side and front. If not

level, tip washer/dryer and adjust feet up or down as shown in

Steps 3 and 4, repeating as necessary.

If washer/dryer is not level, use a 9/16" or 14 mm openend

or adjustable wrench to turn jam nuts clockwise (as viewed

from above) on feet until they are about 1/2" (13 mm)

from the washer/dryer cabinet. Then turn the leveling foot

counterclockwise to lower the washer/dryer or clockwise to raise

the washer/dryer. Recheck levelness of washer/dryer and that all

four feet are firmly in contact with the floor. Repeat as needed.

HELPFUL TIP: You may want to prop up front of washer/dryer

about 4" (102 mm) with a wood block or similar object that will

support weight of washer/dryer.

4. When washer/dryer is level and all four feet are firmly in contact

with the floor, use a 9/16" or 14 mm open-end or adjustable

wrench to turn jam nuts counterclockwise (as viewed from

above) on leveling feet tightly against washer/dryer cabinet.

HELPFUL TiP: You may want to prop washer/dryer with

wooden block.

Not Level LEVEL Not Level

2. Grip washer/dryer from top and rock back and forth, making

sure all four feet are firmly on floor. Repeat, rocking washer/dryer

from side to side. If washer/dryer rocks, go to Step 3 and adjust

leveling feet. If all four feet are in firm contact with floor, go to

Step 4.

La page charge ...

Maytag MLG20PRCWW1 Guide d'installation

Marque: Maytag

Modèle: MLG20PRCWW1

Catégorie: Machines à laver

Taper: Guide d'installation

Ce manuel convient également à

Télécharger le PDF

rapport

dans d''autres langues

English: Maytag MLG20PRCWW1 Installation guide

Maytag MLG20PRCWW1 Guide d'installation

Ce manuel convient également à

Maytag MLG20PRCWW1 Guide d'installation

dans d''autres langues

Documents connexes

Autres documents