Amana ABB1921DEQ Manuel utilisateur

Marque: Amana

Modèle: ABB1921DEQ

Catégorie: Frigos

Taper: Manuel utilisateur

Refrigerator

Form No. A/01/06 Part No. 12828152 www.amana.com Litho U.S.A.

Use & Care Guide

Important Safety Instructions . . . . . . . . . . . . . . . 1-2

Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-9

Temperature Controls . . . . . . . . . . . . . . . . . . . . 10-11

Fresh Food Features . . . . . . . . . . . . . . . . . . . . . 12-14

Freezer Features . . . . . . . . . . . . . . . . . . . . . . . . . . . 15

Ice and Water . . . . . . . . . . . . . . . . . . . . . . . . . . . 16-17

Water Filter . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17-19

Food Storage Tips . . . . . . . . . . . . . . . . . . . . . . . 20-22

Care and Cleaning . . . . . . . . . . . . . . . . . . . . . . 23-26

Operating Sounds . . . . . . . . . . . . . . . . . . . . . . . . . . 27

Troubleshooting . . . . . . . . . . . . . . . . . . . . . . . . 28-30

Warranty & Service . . . . . . . . . . . . . . . . . . . . . . . . . 31

Guide d’utilisation et d’entretien . . . . . . . . . . . . . 32

Guía de uso y cuidado . . . . . . . . . . . . . . . . . . . . . . 64

Bottom Freezer

Important Safety Instructions

WARNING – Hazards or unsafe practices which

COULD result in severe personal injury or death.

WARNING

DANGER – Immediate hazards which WILL result

in severe personal injury or death.

DANGER

CAUTION

What You Need to Know About

Safety Instructions

Warning and Important Safety Instructions appearing in

this guide are not meant to cover all possible

conditions and situations that may occur. Common

sense, caution and care must be exercised when

installing, maintaining or operating appliance.

Always contact the manufacturer about problems or

conditions you do not understand.

Recognize Safety Symbols, Words,

Labels

This appliance is equipped with a three-prong

grounded plug for your protection against possible

electrical shock hazards. It must be plugged into a

properly grounded wall receptacle. Where a standard

two-prong wall receptacle is encountered, it is the

personal responsibility and obligation of the customer

to have it replaced with a properly grounded three-

prong wall receptacle.

Do not, under any

circumstances, cut or remove the third (ground)

prong from the power cord. Do not

use an adapter

plug.

Power supply cord with

three-prong grounded plug

Properly

grounded type

wall receptacle

To reduce risk of injury or death, follow basic

precautions, including the following:

Important:

Child entrapment and suffocation are

not problems of the past. Junked or abandoned

refrigerators are still dangerous – even if they sit out

for “just a few days.” If you are getting rid of your old

refrigerator, please follow the instructions below to

help prevent accidents.

Before you throw away your old

refrigerator or freezer:

• Take off the doors.

• Leave the shelves in place so

children may not easily climb

inside.

• Cut off power cord plug.

DANGER

Installer: Please leave this guide with this appliance.

Consumer: Please read and keep this Use and

Care Guide for future reference; it provides the

proper use and maintenance information.

Keep sales receipt and/or canceled check as proof

of purchase.

Call: 1-800-688-9900 USA

1-800-688-2002 Canada

Have complete model and serial number

identification of your refrigerator. This is located on a

data plate inside the fresh food compartment, on the

upper right side. Record these numbers below for

easy access.

Model Number _______________________________

Serial Number ________________________________

Date of Purchase______________________________

In our continuing effort to improve the quality and

performance of our appliances, it may be necessary

to make changes to the appliance without revising

this guide.

CAUTION – Hazards or unsafe practices which COULD

result in minor personal injury or property damage.

Important Safety Instructions

SAVE THESE INSTRUCTIONS

To reduce risk of fire, electric shock, serious

injury or death when using your refrigerator,

follow basic precautions, including the following:

1. Read all instructions before using the refrigerator.

2. Observe all local codes and ordinances.

3. Be sure to follow grounding instructions.

4. Check with a qualified electrician if you are not

sure this appliance is properly grounded.

Do not ground to a gas line.

Do not ground to a cold-water pipe.

7. Refrigerator is designed to operate on a separate

115 volt, 15 amp., 60 cycle line.

Do not modify plug on power cord. If plug does

not fit wall receptacle, have proper receptacle

installed by a qualified electrician.

Do not use a two-prong adapter, extension cord

or power strip.

10. Do not remove warning tag from power cord.

11.

Do not tamper with refrigerator controls.

12.

Do not service or replace any part of refrigerator

unless specifically recommended in Use and Care

Guide or published user-repair instructions.

Do not attempt service if instructions are not

understood or if they are beyond personal skill

level.

13. Always disconnect refrigerator from electrical

supply

before attempting any service. Disconnect

power cord by grasping the plug, not the cord.

14. Install refrigerator according to Installation

Instructions. All connections for water, electrical

power and grounding must comply with local

codes and be made by licensed personnel when

required.

15. Keep your refrigerator in good condition. Bumping

or dropping refrigerator can damage refrigerator

or cause refrigerator to malfunction or leak. If

damage occurs, have refrigerator checked by

qualified service technician.

16. Have worn power cords and/or loose plugs

replaced by a qualified service technician.

17. Always read and follow manufacturer’s storage

and ideal environment instructions for items being

stored in refrigerator.

18. Your refrigerator

should not be operated in the

presence of explosive fumes.

19. Children should not climb, hang or stand on any

part of the refrigerator.

20. Clean up spills or water leakage associated with

water installation.

WARNING

Installation

Materials Needed:

•

⁄8” hex head driver

• Carpenter’s level.

1. Remove toe grille.

• Grasp firmly and pull

outward to unclip.

2. Using hex head driver, turn

the front adjustment screws

(A) on each side to

raise or lower the front of the refrigerator (see

illustration below).

3. Using the hex head driver, turn each of these

adjustment screws

(B) to raise or lower the rear of

the refrigerator.

4. Using a carpenter’s level, make sure front of

refrigerator is

⁄4” (6 mm) or

⁄2 bubble higher than

back of refrigerator and that the refrigerator is level

from side to side.

5. Turn stabilizing legs

against floor.

6. Turn adjustment screws

(A) counterclockwise to

allow the full weight of the refrigerator to rest on

the stabilizing legs.

7. Replace the toe grille.

Your refrigerator was packed carefully for shipment.

Remove and discard shelf packaging and tape.

Do not

remove the serial plate.

Location

• Do not install refrigerator near oven, radiator or other

heat source. If not possible, shield refrigerator with

cabinet material (contact a qualified contractor).

•

Do not install where temperature falls below 55° F

(12° C) or rises above 110° F (43° C). Malfunction may

occur at this temperature.

•

Refrigerator is designed for indoor household

application only.

Measuring the Opening

When installing your refrigerator, measure carefully.

Allow

⁄2” space at top and

⁄2” space behind the machine

compartment cover (located in the rear) for proper air

circulation.

Subflooring or floor coverings (i.e. carpet, tile, wood

floors, rugs) may make your opening smaller than

anticipated.

Some clearance may be gained by using the leveling

procedure under

Leveling.

Important: If refrigerator is to be installed into a recess

where the top of the refrigerator is completely covered,

use distance from floor to top of hinge cap to verify

proper clearance.

Transporting Your Refrigerator

• NEVER transport refrigerator on its side. If an upright

position is not possible, lay refrigerator on its back.

Allow refrigerator to sit upright for approximately 30

minutes

before plugging it in to assure oil returns to

the compressor. Plugging the refrigerator in

immediately may cause damage to internal parts.

• Use an appliance dolly when moving refrigerator.

ALWAYS truck refrigerator from its side or

back–

NEVER from its front.

• Protect outside finish of refrigerator during transport

by wrapping cabinet in blankets or inserting padding

between the refrigerator and dolly.

• Secure refrigerator to dolly firmly with straps or

bungee cords. Thread straps through handles when

possible.

Do not over-tighten. Over-tightening

restraints may dent or damage outside finish.

To protect property and refrigerator from

damage, observe the following:

• Protect vinyl or other flooring with cardboard, rugs,

or other protective material.

•

Do not use power tools when performing leveling

procedure.

CAUTION

To enhance the appearance and maintain performance,

the refrigerator should be leveled per instructions

below.

Notes:

• Complete any required water supply connection

before leveling.

• Some models only have adjustment screws

(A).

• Align the toe grille mounting clips with the lower

cabinet slots.

• Push the toe grille firmly until it snaps into place.

Leveling

Installation

To avoid electrical shock which can cause

severe personal injury or death, observe the

following:

• Disconnect power to refrigerator before removing

doors or drawer. Connect power only after

replacing doors or drawer.

WARNING

To avoid damage to walls and flooring, protect vinyl

or other flooring with cardboard, rugs or other

protective material.

CAUTION

Door and Drawer Removal

Some installations require door/drawer removal to

transport the refrigerator to its final location.

Pullout Freezer Drawer

To avoid electrical shock, which can cause severe

personal injury or death, disconnect power to

refrigerator

before removing doors. After replacing

doors, connect power.

WARNING

To prevent accidental child entrapment or

suffocation risk,

do not remove the divider in the

top freezer basket.

DANGER

To avoid possible injury, product, or property

damage, you will need two people to perform the

following instructions.

CAUTION

6. Lift top of drawer front to

unhook supports from rail

system. Lift door front out to

remove.

To Remove:

1. Pull drawer open to full extension.

2. Pull upper basket out to full extension and lift out

to remove.

3. Lift lower basket straight up and out to remove.

4. On each side rail is a

basket cradle with two snap

attachments. To release

each cradle, unlatch the

snaps by pushing them

inward, away from the side

rail system. Lift the cradles

off of the rails.

5. Remove Phillips screw from

each side of rail system (select

models).

1. Unplug power cord from power source.

2. Remove toe grille (see page 3).

3. Remove top hinge cover from

refrigerator door by removing Phillips

screw and retain screw and cover for

later use.

4. Unscrew

⁄16” hex head screws from

top hinge to remove hinge and retain

all screws for later use.

5. Lift refrigerator door from center

hinge pin.

6. Remove plastic sleeve, if present.

Remove center hinge pin with a

⁄16” hex

head driver. Retain hinge pin and

plastic sleeve for later use.

7. Remove Phillips screws to remove

center hinge and retain all

screws for later use.

8. Remove bottom hinge or

stabilizing bracket with

⁄8” hex

head driver and retain screws

for later use. Lift out bottom

hinge pin (on freezer door

models).

9. See pages 4-5 for drawer removal

instructions.

Installation

Reinstallation of the Doors

1. Install hinge assemblies:

• Install top hinge loosely with

⁄16” hex head

screws.

• Install center hinge with Phillips screws.

•

Freezer door models: Install bottom hinge with

⁄8” hex head screws.

Freezer door models: Insert bottom

hinge pin.

• Locate bottom hinge hole closest to

outside edge of cabinet, and insert

bottom hinge pin. Replace any door

shims, if present.

Freezer door models: Place hinge

side of freezer door on bottom hinge

pin and hold freezer door upright

while installing center hinge pin with

⁄16” hex head driver.

• Replace plastic sleeve.

• Replace any applicable door shims.

• Make sure the hinge pin is installed tightly.

4. Place hinge side of refrigerator

door on center hinge pin.

5. While holding refrigerator door

upright, tighten down top hinge

with

⁄16” hex head driver and

replace hinge cover.

Door Reversal

In some installations, reversing the door swing allows

for more convenient access to stored items. Both

doors can be reversed on freezer door models and the

fresh food door is reversible on freezer drawer models.

1. Remove door(s) (see page 4).

2. Transfer cabinet plugs and cabinet

screws to opposite side of cabinet.

• Remove cabinet plugs with flat

blade of screwdriver tip wrapped

in masking tape.

• Remove center mullion screws

with

⁄16” hex head screwdriver.

•

Freezer door models: Remove

bottom mullion screws with

⁄8” hex head driver.

2. While supporting door front,

hook supports into tabs

located on inside of rail.

To Install:

1. Pull both rails out to full

extension.

3. Lower door front into

final position.

4. Replace and tighten Phillips screws that were

removed from each side of rail system (select

models).

5. Place the basket cradles back onto the side rails.

Align snaps with the slots on the side rails and

press each snap towards the rail until it clicks.

6. With rails pulled out to full extension, set the

basket straight down into the basket cradles.

7. Slide upper basket into freezer. Make sure that rear

of basket hooks behind rail catch.

Basket cradle

snap attachments

Installation

3. Transfer door stops from bottom edge of fresh food

door and freezer door, if applicable, to opposite

side of door edge.

• Use a Phillips screwdriver

for removal and installation.

4. Install handles (see below

and page 7).

5. Reinstall the door(s).

Handles

Remove and discard handle packaging and tape.

Handle design varies from refrigerator to refrigerator.

Please reference the appropriate instructions for your

model below.

Fresh Food Handles

Standard Front Mount Handle

Materials Needed:

• Phillips screwdriver

•

⁄16” hex head driver

To Install:

1. Remove

⁄4” hex head screws from

door face with hex head driver, and

Phillips screw from top of door.

• If reversing door, remove door

plugs from opposite side of door and insert in

screw holes.

2. Align handle holes with screw holes on

door face and secure with two door face

screws from step 1.

To avoid possible injury and damage to property:

• Place doors on a nonabrasive surface protected by

towels or rugs while working directly on doors.

CAUTION

Note: If not installed, the handle is located in the

interior of the fresh food section or attached to the

back of your refrigerator.

4. Ensure the door handle is snug to the

door panel.

To Remove:

Reverse installation procedure.

Upper

Handle

Lower

Handle

3. Locate handle trim in literature pack and

install over top and bottom of handle, as

illustrated.

• Secure top handle trim with remaining

screw removed in step 1.

• Snap bottom trim over bottom portion

of handle.

To Remove:

1. Remove top handle trim by removing top

handle screw.

• Retain trim and screw for later

replacement.

2. Pry bottom handle trim from handle with

screwdriver flat blade wrapped in

masking tape.

• Retain trim for later replacement.

3. Remove two hex head screws.

• Retain screws for later replacement.

Side Mount Handle

Materials Needed:

• Phillips screwdriver

To Install:

1. Remove screws from the side of the

door.

2. Align the side mount handle with the

predrilled holes in the door panel.

3. Insert the screws in the sequence as

shown.

Installation

Notes:

• There is a slight curve to

this style of freezer handle.

• For proper installation, be

sure handle is oriented as

shown.

Freezer Handles

Partial-Width Handle

Materials Needed:

• Phillips screwdriver

To Install:

1. Install handle by fastening with

screws removed from edge of door.

• If reversing freezer door, remove

door plugs from top edge of door

and insert into screw holes.

To Remove:

1. Remove handle screws with Phillips

screwdriver and retain screws for

later use.

Front Mount Plastic Freezer Handle

To Install:

1. Align door handle

clips to the studs

attached to the

freezer door.

2. Ensure the large

hole in the

mounting clip is

positioned to the

right on both ends

of the handle.

3. Rotate the handle so that the handle is flat against

the door.

4. Grasp the handle firmly and slide handle to the

right.

To Remove:

1. With both hands, firmly grasp the handle toward

the right side.

2. Slide toward the

left, lift and remove from the

surface.

Handle

Clip

Handle

Base

Door Stud

Installation

Connecting the Water Supply

To reduce the risk of injury or death, follow

basic precautions, including the following:

• Read all instructions before installing ice maker.

•

Do not attempt installation if instructions are not

understood or if they are beyond personal skill

level.

• Observe all local codes and ordinances.

•

Do not service ice maker unless specifically

recommended in Use & Care Guide or published

user-repair instructions.

• Disconnect power to refrigerator

before installing

ice maker.

• Water damage due to an improper water

connection may cause mold/mildew growth. Clean

up spills or leakage immediately!

WARNING

To avoid property damage or possible injury,

follow basic precautions, including the

following:

• Consult a plumber to connect

⁄4” O.D. copper

tubing to household plumbing to assure

compliance with local codes and ordinances.

• Confirm water pressure to water valve is between

35 and 100 pounds per square inch, 20 pounds

per square inch without filter.

•

Do not use a self-piercing or

⁄16” saddle valve.

Both reduce water flow and can become clogged

over time, and may cause leaks if repair is

attempted.

• Tighten nuts by hand to prevent cross threading.

Finish tightening nuts with pliers and wrenches.

Do not over-tighten.

• Wait two to three hours

before placing refrigerator

into final position to check and correct any water

leaks. Recheck for leaks after 24 hours.

• Verify the copper tubing under the sleeve is

smooth and free from defects.

Do not reuse an

old sleeve.

CAUTION

Materials Needed:

•

⁄4” outer diameter flexible copper tubing

• Shut-off valve (requires a

⁄4” hole to be drilled into

water supply line

before valve attachment)

• Adjustable wrench (2)

•

⁄4” hex nut driver

Notes:

• Use copper tubing only for installation. Plastic is

less durable and can cause damage.

• Add 8’ to tubing length needed to reach water

supply for creation of service loop.

1. Create service loop with copper

tubing (minimum 2’ diameter).

Avoid kinks in the copper tubing

when bending the service loop.

Do not use plastic tubing.

2. Remove plastic cap from water valve

inlet port.

3. Place brass nut

(A) and sleeve (B)

on copper tube end as illustrated.

Reminder: Do not use an old

sleeve. The nut and sleeve are

provided in the Use and Care

packet.

4. Place end of copper tubing into

water valve inlet port. Shape

tubing slightly.

Do not kink – so

that tubing feeds straight into inlet

port.

2’ diameter

minimum

Installation

5. Slide brass nut over sleeve and

screw nut into inlet port.

Place adjustable wrench on nut

(1) attached to plastic waterline

and maintain position.

Using second adjustable wrench

turn the lower nut

(2)

counterclockwise and fully tighten

while holding the upper nut in

place.

Important: Do not over-tighten. Crossthreading

may occur.

6. Pull on tubing to confirm

connection is secure. Connect

tubing to frame with water

tubing clamp

water supply. Check for leaks

and correct if necessary.

Continue to observe the water

supply connection for two to

three hours prior to moving the

refrigerator to its permanent

location.

7. Monitor water connection for 24

hours. Correct leaks, if necessary.

1. Create service loop with copper

tubing (minimum 2’ diameter).

Avoid kinks in the copper tubing

when bending the service loop.

Do not use plastic tubing.

2. Remove plastic cap from water

valve inlet port.

3. Place brass nut

(A) and sleeve (B)

on copper tube end as illustrated.

Reminder: Do not use old sleeve.

The nut and the sleeve are

provided in the use and care

packet.

4. Place end of copper

tubing into water valve

inlet port. Shape tubing

slightly.

Do not kink –

so that tubing feeds

straight into inlet port.

5. Slide brass nut over sleeve and screw nut

into inlet port. Tighten nut with wrench.

Important: Do not over-tighten.

Crossthreading may occur.

6. Pull on tubing to confirm connection is

secure. Connect tubing to frame with

water tubing clamp

water supply. Check for leaks and

correct if necessary. Continue to observe

the water supply connection for two to

three hours prior to moving the

refrigerator to its permanent location.

7. Monitor water connection for 24 hours.

Correct leaks, if necessary.

2’ diameter

minimum

Alternate connection (select models)

Materials Needed:

•

⁄4” outer diameter flexible copper tubing

• Shut-off valve (requires a

⁄4” hole to be drilled into

water supply line before valve attachment)

• Adjustable wrench

•

⁄4” hex nut driver

Notes:

• Use copper tubing only for installation. Plastic is

less durable and can cause damage.

• Add 8’ to tubing length needed to reach water

supply for creation of service loop.

Temperature Controls

Dial Temperature Controls

(select models)

The controls are located at the top front of the

refrigerator and freezer compartments.

Note: The freezer control turns the cooling system

on. Neither section will cool if freezer control is set

to OFF.

Refrigerator Control

Freezer Control

Initial Control Settings

After plugging the refrigerator in, set the controls.

• To adjust the controls, turn the control knob to the

left or right as desired.

• The temperature control range for both

compartments is 1 through 7 (coldest).

• Set the Freezer control on

• Set the Refrigerator control on

• Let the refrigerator run at least 8 to 12 hours

before

adding food.

Warm Cabinet Surfaces

At times, the front of the refrigerator cabinet may be

warm to the touch. This is a normal occurrence that

helps prevent moisture from condensing on the

cabinet. This condition will be more noticeable when

you first start the refrigerator, during hot weather and

after excessive or lengthy door openings.

Adjusting the Controls

• 24 hours after adding food, you may decide that one

or both compartments should be colder or warmer. If

so, adjust the control(s) as indicated in the

Temperature Control Guide table below. See page 20

for instructions on checking compartment

temperature.

• Except when starting the refrigerator,

do not change

either control more than one number at a time.

• Allow 24 hours for temperatures to stabilize.

• Changing either control will have some effect on the

temperature of the other compartment.

Temperature Control Guide

Refrigerator too warm

Refrigerator too cold

Freezer too warm

Freezer too cold

Turn refrigerator OFF

Turn the Refrigerator control

to next higher number.

Turn the

Refrigerator

control to next lower number.

Turn the

Freezer control to

next higher number.

Turn the

Freezer control to

next lower number.

Turn the

Freezer control to

OFF.

Note: Turning freezer control to OFF stops cooling

in both compartments. It does not shut off power to

the refrigerator.

Temperature Controls

Touch Temperature Controls

(select models)

The controls are located at the top front of the

refrigerator compartment.

Control

Initial Control Settings

After plugging the refrigerator in, set the controls.

• Pressing the or pads adjusts the controls

to the desired setting.

• The temperature control range for both

compartments is 1 through 7 (coldest).

• Set the Freezer control on

• Set the Refrigerator control on

• Let the refrigerator run at least 8 to 12 hours

before

adding food.

Warm Cabinet Surfaces

At times, the front of the refrigerator cabinet may be

warm to the touch. This is a normal occurrence that

helps prevent moisture from condensing on the

cabinet. This condition will be more noticeable when

you first start the refrigerator, during hot weather and

after excessive or lengthy door openings.

Adjusting the Controls

• 24 hours after adding food, you may decide that one

or both compartments should be colder or warmer. If

so, adjust the control(s) as indicated in the

Temperature Control Guide table below. See page 20

for instructions on checking compartment

temperature.

• Except when starting the refrigerator,

do not change

either control more than one number at a time.

• Allow 24 hours for temperatures to stabilize.

Temperature Control Guide

Refrigerator too warm

Refrigerator too cold

Freezer too warm

Freezer too cold

Turn refrigerator OFF

Set the Refrigerator control

to next higher number by

pressing the pad.

Set the Refrigerator control

to next lower number by

pressing the pad.

Set the Freezer control to

next higher number by

pressing the pad.

Set the Freezer control to

next lower number by

pressing the pad.

Press the

Refrigerator or

Freezer pad until a dash

(–) appears in the display.

Fresh Food Features

Shelves

To avoid personal injury or property damage,

observe the following:

• Never attempt to adjust a shelf that is loaded with

food.

• Confirm shelf is secure

before placing items on

shelf.

• Handle tempered glass shelves carefully. Shelves

may break suddenly if nicked, scratched, or

exposed to sudden temperature change.

CAUTION

Door Storage

Dairy Center

The Dairy Center provides

convenient door storage for

spreadable items such as butter

and margarine. This compartment can be moved to

different locations to accommodate storage needs. To

use the dairy center, raise the cover.

To Remove:

• Raise the cover, pull upward and tilt out.

To Install:

• Reverse above procedure.

Door Buckets

Door Buckets can be moved to

meet storage needs.

To Remove:

• Slide bucket up and pull straight out.

To Install:

• Slide bucket in and down until firmly seated in the

door liner.

Full-Width Door Shelf

Full-Width Door Shelf removes for easy cleaning.

To Remove:

• Slide shelf up and pull straight out.

To Install:

• Reverse above procedure.

Your refrigerator has either Spillsaver™ or non-sealed

shelves. The Spillsaver™ shelves have a spill retainer

edge which allows for easier clean up and some are

equipped with the EasyGlide™ slide out feature. To

slide out (select models), grasp the front of the shelf

and pull forward. Push in the shelf to return to the

original position.

To Remove a Shelf:

• Slightly tilt up the front and lift up

the rear of the shelf, then pull the

shelf straight out.

To Lock the Shelf Into Another Position:

• Tilt up the front edge of the shelf.

• Insert the hooks into the desired frame openings and

let the shelf settle into place.

• Be sure the shelf is securely locked at the rear.

The Crisper Top serves as the lower fresh food shelf.

To Remove the Crisper Top:

• Remove drawers as indicated on pages 13 and 14.

• Place hand under the frame to push up the glass. Lift

glass out.

• Lift frame from refrigerator liner rails.

• To install, repeat above instructions in reverse order.

Fresh Food Features

Note: For best results, keep the crispers tightly

closed.

To Remove:

• Pull drawer out to full extension. Tilt up front of

drawer and pull straight out.

To Install:

• Insert drawer into frame rails and push back into

place.

Storage Drawers

Snack Drawer (select models)

The Snack Drawer can be used for

storage of miscellaneous items or

extra produce.

To Remove:

• Pull drawer out to full extension. Tilt up front

of drawer and pull straight out.

To Install:

• Insert drawer into frame rails and push back into

place.

Crisper Drawers

The Crisper Drawers provide a higher humidity

environment for fresh fruit and vegetable storage.

Controls

The Crisper Controls regulate the amount of humidity

in the crisper drawer. Slide the control toward the low

setting for produce with outer skins. Slide the control

toward the high setting for leafy produce.

Beverage Chiller™

(select models)

The Beverage Chiller™ keeps

beverages and other items cooler

than the rest of the fresh food

section. A cold air inlet allows air from the freezer

section to pass into the beverage chiller.

The Beverage Chiller™ control is located

on the left wall of the fresh food

compartment. The control adjusts the

amount of cold air allowed in to the

beverage chiller. For a cooler temperature

in the Beverage Chiller™, slide the control

down.

To Remove:

• First remove the pick off

shelf to the left of the

Beverage Chiller™.

• Firmly hold each side of

beverage chiller, lift up

and away from door liner.

To Install:

• Reverse above procedure.

Note: Cold air diverted into the Beverage Chiller™

can decrease the main refrigerator temperature.

Refrigerator control may need to be adjusted.

Fresh Food Features

Beverage Organizer™ (select models)

The Beverage Organizer™ slides out from underneath

the Spillsaver™ shelf. The Beverage Organizer™ holds

up to twelve 12-ounce beverage cans.

To Remove:

• Pull out to full extension. Tilt up the front of the

Beverage Organizer™ and pull straight out.

To Install:

• Insert Beverage Organizer™ into frame rails and push

back into place.

Accessories

Wine Trivet/Can Rack (select models)

The Wine Trivet/Can Rack

accessory fits in the Chef’s Pantry™

or on a shelf.

Bottles or cans can be laid crosswise,

or a single bottle may be laid in the

center depression.

Grip Pads (select models)

The Grip Pads prevent objects from sliding in the door

buckets. Grip Pads are removable

and are top-rack dishwasher safe for

easy cleaning.

Temperature-Controlled Drawer

(select models)

The Chef’s Pantry™ drawer is a full-width drawer with

adjustable temperature control. This drawer can be

used for large party trays, deli items, beverages or

miscellaneous items.

There is a temperature control which adjusts the

amount of cold air allowed into the Chef’s Pantry™.

The control is located on the right side of the drawer.

Depending on your model, it is either on the front of

the drawer or under the lid.

Set the control to

cold or to provide a normal

refrigerator temperature. Set the drawer on the

coldest or setting when a temperature colder than

the main refrigerator compartment is desired. Use the

coldest setting when storing meats.

To Remove:

• Lift lid (select models). Pull drawer out to full

extension. Tilt up front of pantry and pull straight out.

To Install:

• Push metal glide rails to the back of the refrigerator

(select models). Place drawer onto rails and slide

drawer back until it falls into place.

Some models feature a divider to organize the Chef’s

Pantry™ into sections.

To Remove:

• Pull drawer completely out and raise the front of the

divider to unhook it from the rear wall of the pantry

and lift it out.

To Install:

• Hook back of divider over rear wall of pantry and

lower into place.

Notes:

• Cold air directed to the Chef’s Pantry™ can

decrease refrigerator temperature. Refrigerator

control may need to be adjusted.

•

Do not place leafy vegetables in the Chef’s

Pantry™ drawer. Colder temperatures could

damage leafy produce.

Freezer Features

Accessories

Ice Cube Tray (select models)

The Ice Cube Tray provides an area to

freeze cubes for manual

dispensing of ice.

To release ice cubes from tray,

hold tray upside down over a

storage container and twist

both ends of tray until cubes release.

Ice Service Rack (select models)

The Ice Service Rack holds the ice cube tray.

To Install:

• Slide L-shaped groove of shelf

down over back wall screw.

Push rack back until screw is

stopped in L-shaped groove

(1). Slide front portion of shelf over front wall

screw (2).

To Remove:

• Perform above steps in reverse order.

Shelves and Baskets

Models with swing freezer door:

Freezer Shelf (select models)

Select models have a shelf divider.

To Remove:

• Pull shelf out to full

extension. Tilt up front of

shelf and pull straight out.

To Install:

• Insert shelf into freezer liner rails and push to back

of compartment.

Wire Basket (select models)

To Remove:

• Pull basket out to full

extension. Tilt up front of

basket and pull straight out.

To Install:

• Insert basket into freezer liner rails and push back

into place.

Freezer Door Shelf (select models)

The Freezer Door Shelf provides

convenient storage for frozen food

items in freezer door.

To Remove:

• Lift shelf from side liner tabs and pull

out.

To Install:

• Fit ends of shelf on liner tabs and slide down.

Note: Freezer Drawer Models: See page 5 for

lower basket and complete pullout drawer

instructions.

Upper Wire Basket

To Remove:

• Pull upper basket out to full extension and lift out to

remove.

To Install:

• Slide upper basket into freezer. Make sure that rear

of basket hooks behind rail catch.

To prevent accidental child entrapment or

suffocation risk, do not remove the divider in the

top freezer basket

DANGER

Models with pullout freezer drawer:

Ice and Water

Automatic Ice Maker

(select models)

Note: Energy rating guides that are posted on the

refrigerator at the time of purchase do not include

optional ice maker energy usage.

To avoid personal injury or property damage,

observe the following:

• Do not place fingers or hands on the automatic

ice making mechanism while the refrigerator is

plugged in. This will help protect you from possible

injury. It will also prevent interference with moving

parts of the ejector mechanism and the heating

element that releases the cubes.

• Under certain rare circumstances, ice cubes may

be discolored, usually appearing with a green-

bluish hue. The cause of this unusual discoloration

can be a combination of factors such as certain

characteristics of local waters, household

plumbing and the accumulation of copper salts in

an inactive water supply line which feeds the ice

maker. Continued consumption of such discolored

ice cubes may be injurious to health. If such

discoloration is observed, discard the ice cubes

and contact your dealer to purchase and install a

water line filter.

• Water damage due to improper water connection

may cause mold/mildew growth.

• Clean up water and ice spills to avoid personal

injury and to prevent mold/mildew growth.

WARNING

Some models are automatic ice maker ready. The

number of the appropriate ice maker kit is IC11B. The

kit contains installation instructions and water

connection instructions.

Other models have a factory installed ice maker.

Connect the ice maker to the water supply as

instructed on page 9.

Proper water flow and a level

refrigerator are essential for optimal ice maker

performance.

Operating Instructions

• Confirm ice bin is in place and ice maker arm is

down.

• After freezer section reaches

approximately 0° F (-18° C), ice

maker fills with water and begins

operating. You will have a complete

harvest of ice approximately every

three hours.

• Allow approximately 24 hours after installation to

receive first harvest of ice.

• Discard ice created within first 12 hours of operation

to assure system is flushed of impurities.

• Stop ice production by raising ice maker arm until

click is heard.

• Ice maker will remain in the off position until arm is

pushed down.

• The first one or two batches will probably contain

undersized and irregular cubes because of air in the

supply line.

• When the ice cubes are ejected it is normal for

several cubes to be joined together at the ends. They

can easily be broken apart. The ice maker will

continue to make ice until the supply of ice cubes

raises the sensor arm, shutting the ice maker off.

• Certain sounds may accompany the various cycles of

the ice maker. The motor may have a slight hum, the

cubes will rattle as they fall into an empty storage bin

and the water valve may click or “buzz” occasionally.

• If the ice is not used frequently, the ice cubes will

become cloudy, shrink, stick together and taste stale.

Empty the ice storage bin periodically and wash it in

lukewarm water. Be sure to dry the bin thoroughly

before replacing it.

• Beverages and foods

should not be placed in the

ice storage bin for quick chilling. These items can

block the sensor arm, causing the ice maker to

malfunction.

• Turn off (arm up) the ice maker when the water

supply is to be shut off for several hours.

To Remove the Ice Bin:

• Pull it forward, away from the ice maker. To avoid the

ice maker dumping ice while the bin is removed, turn

the ice maker off by raising the sensor arm.

To Install the Ice Bin:

• Reverse the above procedure. Turn the ice maker on

by lowering the sensor arm.

Ice and Water

Water Dispenser (select models)

The Water Dispenser is located on the left side wall of

the fresh food section. This design is for cold water

dispensing only.

Water Filter (select models)

Removal and Installation

To avoid serious illness or death, do not use

refrigerator where water is unsafe or of unknown

quality without adequate disinfection before or after

use of filter.

WARNING

After installing a new water filter, always

dispense water for two minutes before

removing the filter for any reason.

• The bypass cap does not filter water. Be sure to

have replacement cartridge available when filter

change is required.

• If water filtration system has been allowed to

freeze, replace filter cartridge.

• If system has not been used for a short period of

time, and water has an unpleasant taste or odor,

flush system by dispensing two to three glasses of

water. If unpleasant taste or odor persists, change

filter cartridge. If system has not been used for

three months or more, replace water filter

cartridge (see page 26).

CAUTION

Initial Installation

The water filter is located in the upper right hand

corner of the fresh food compartment.

1. Remove blue bypass cap and

retain for later use.

2. Remove sealing label from end

of filter and insert into filter

head.

3. Rotate gently clockwise until

filter stops. Snap filter cover

closed.

4. Reduce water spurts by flushing

air from system. Run water

continuously for two minutes through dispenser

until water runs steady. During initial use, allow

about a one- to two-minute delay in water

dispersal to allow internal water tank to fill.

• Additional flushing may be required in some

households where water is of poor quality.

Replacing Water Filter

Important: Air trapped in system may cause

water and cartridge to eject. Always dispense

water for two minutes before removing the filter

for any reason. Use caution when removing.

1. Turn filter counterclockwise until it releases from

filter head.

2. Drain water from filter into sink, and dispose in

normal household trash.

3. Wipe up excess water in filter cover and continue

with

Initial Installation, steps 2 and 4.

The filter should be changed at least every 12 months.

Important: Condition of water and amount used

determines life span of water filter cartridge. If water

use is high, or if water is of poor quality, replacement

may need to take place more often.

To purchase a replacement water filter cartridge,

contact your dealer or call 1-877-232-6771 USA or

1-800-688-8408 Canada.

The dispenser feature may be used without a water

filter cartridge. If you choose this option, replace filter

with blue bypass cap.

To Dispense Water:

• Hold container under spout and

press dispenser pad.

Water Filter (select models)

System Specification and Performance Data Sheet

Refrigerator Water Filter Cartridge Model UKF8001AXX

Specifications

Service Flow Rate (Maximum).............................................0.78 GPM (2.9 L/min)

Rated Service Life UKF8001AXX-750 (Maximum)......750 gallons/2838 liters

Maximum Operating Temperature .....................................100° F / 38° C

Minimum Pressure Requirement........................................35 psi /241 kPA

Minimum Operating Temperature......................................33° F/1° C

Maximum Operating Pressure.............................................120 psi /827 kPA

Performance Data

1000 Apollo Road

Eagan, Minnesota 55121-2240

651.450.4913

EPA EST #35917-MN-1

100834/B

The PuriClean

II retractable water filtration system

uses a UKF8001AXX replacement cartridge. Timely

replacement of filter cartridge is essential for

performance satisfaction from this filtration system.

Please refer to the applicable section of your Use &

Care Guide for general operation, maintenance

requirements and troubleshooting.

This system has been tested according to ANSI/NSF 42

and 53 for reduction of the substance listed above. The

concentration of the indicated substances in water

entering the system was reduced to a concentration less

than or equal to the permissible limit for water leaving

the system, as specified in ANSI/NSF 42 and 53.

* Tested using a flow rate of 0.78 gpm; pressure of 60 psig; pH of 7.5 + 0.5; temp. of

68° + 5° F (20° + 3° C)

** Measurement in Particles /ml. Particles used were 0.5 - 1 microns

*** NTU - Nephelometric Turbidity Units

General Use Conditions

Read this Performance Data Sheet and compare the

capabilities of this unit with your actual water

treatment needs.

DO NOT use this product where water is

microbiologically unsafe or of unknown quality

without adequate disinfection before or after the

system. System certified for cyst reduction may be

used on disinfected water that may contain

filterable cysts.

USE ONLY WITH COLD WATER SUPPLY. CHECK

FOR COMPLIANCE WITH THE STATE AND LOCAL

LAWS AND REGULATIONS.

Standard No. 42: Aesthetic Effects

Taste and Odor Reduction

Chlorine Taste & Odor

Mechanical Filtration Unit

Particulate Reduction Class 1

Standard No. 53: Health Effects

Chemical Reduction Unit

Lead, Atrazine, Lindane, Benzene,

Carbofuran, 1,4-Dichlorobenzene,

Mercury & Toxaphene Reduction

Mechanical Filtration Unit

Cyst, Turbidity and Asbestos Reduction

Tested and certified by NSF International against ANSI/NSF Standards 42 & 53

in models UKF8001AXX-750 for the reduction of:

Parameter

Chlorine

T & O

Particulate**

USEPA

MCL

—

Standard No. 42: Aesthetic Effects

Influent

Challenge Concentration

2.0 mg/L ± 10%

—

at least 10,000 particles/ml

Influent

Average

1.88 mg/L

—

5,700,000 #/ml

Average

<0.05136364 mg/L

—

30,583 #/ml

Maximum

0.06 mg/L

—

69,000 #/ml

Average

>97.26%

—

99.52%

Minimum

96.84%

—

98.94%

Min. Required

Reduction

50%

—

85%

Effluent % Reduction

Parameter

Turbidity

Cysts

Asbestos

Lead at pH 6.5

Lead at pH 8.5

Mercury at pH 6.5

Mercury at pH 8.5

Atrazine

Benzene

Carbofuran

1,4-Dichlorobenzene

Lindane

Toxaphene

USEPA

MCL

1 NTU**

99.5% Reduction

99% Reduction

0.015 mg/L

0.002 mg/L

0.003 mg/L

0.005 mg/L

0.04 mg/L

0.075 mg/L

0.0002 mg/L

0.003 mg/L

Standard No. 53: Health Effects

Influent

Challenge Concentration

11 ± 1 NTU***

Minimum 50,000/L

fibers/L; fibers >10 micrometers in length

0.15 mg/L + 10%

.006 mg/L ± 10%

0.009 mg/L + 10%

0.015 mg/L ± 10%

0.08 mg/L ± 10%

.225 mg/L ± 10%

0.002 mg/L + 10%

0.015 ± 10%

Influent

Average

10.7 NTU

166,500 #/L

155 MF/L

0.153 mg/L

0.150 mg/L

0.006 mg/L

0.009 mg/L

0.014 mg/L

0.081 mg/L

0.208 mg/L

0.002 mg/L

0.015 mg/L

Average

0.31 NTU

<1 #/L

<1 MF/L

<.001 mg/L

0.0003 mg/L

0.0008 mg/L

<0.002 mg/L

0.0006 mg/L

<0.001 mg/L

<0.0005 mg/L

0.000 mg/L

<0.001 mg/L

Maximum

.049 NTU

<1 #/L

<1 MF/L

<.001 mg/L

0.0005 mg/L

0.0015 mg/L

0.002 mg/L

0.0011 mg/L

<0.001 mg/L

<0.0005 mg/L

<0.0001 mg/L

<0.001 mg/L

Average

97.09%

>99.99%

>99.35%

>99.33%

95.70%

86.22%

76.99%

95.71%

98.74%

99.76%

98.72%

92.97%

Minimum

95.20%

>99.99%

>99.29%

90.91%

75.93%

75.31%

92.14%

98.46%

99.74%

96.50%

91.67%

Min. Required

Reduction

0.5 NTU

>99.95%

99%

0.10 mg/L

0.002 mg/L

0.003 mg/L

0.005 mg/L

0.04 mg/L

0.075 mg/L

0.0002 mg/L

0.003 mg/L

Effluent % Reduction

Water Filter (select models)

State of California

Department of Health Services

Water Treatment Device

Certificate Number

03 - 1583

Date Issued: September 16, 2003

Trademark /Model Designation Replacement Elements

PuriClean

II UKF8001AXX750 UKF8001AXX

Manufacturer: PentaPure Inc.

The water treatment device(s) listed on this certificate have met the testing requirements pursuant to Section 116830 of the

Health and Safety Code for the following health related contaminants:

Microbiological Contaminants and Turbidity Inorganic/Radiological Contaminants

Cysts Asbestos

Turbidity Lead

Mercury

Organic Contaminants

Atrazine

Lindane

Toxaphene

Rated Service Capacity: 750 gal. Rated Service Flow: 0.78 gpm

Conditions of Certification:

Do not use where water is microbiologically unsafe or with water of unknown quality, except that systems certified for cyst

reduction may be used on disinfected waters that may contain filterable cysts.

La page charge ...

Amana ABB1921DEQ Manuel utilisateur

Marque: Amana

Modèle: ABB1921DEQ

Catégorie: Frigos

Taper: Manuel utilisateur

Télécharger le PDF

rapport

dans d''autres langues

español: Amana ABB1921DEQ Manual de usuario
português: Amana ABB1921DEQ Manual do usuário

Amana ABB1921DEQ Manuel utilisateur

Amana ABB1921DEQ Manuel utilisateur

dans d''autres langues

Documents connexes

Autres documents